Login- Download PDF Manual
-
to ensure efficient heating and defrosting. Since the condenser is located in front of the radiator, this area should be kept clean because cooling performance is impaired by any accumulation of insects and leaves on the condenser.
& Efficient cooling after parking
in direct sunlight
After parking in direct sunlight, drive with the windows open for a few minutes to allow outside air to circulate into the
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (158,1)
& Air conditioner compressor
shut-off when engine is heavily loaded
To improve acceleration and gas mileage, the air conditioner compressor is designed to temporarily shut off during air condi- tioner operation whenever the accelerator is fully depressed such as during rapid acceleration or when driving on a steep upgrade.
& Refrigerant for your climate
control system
Your air conditioner uses ozone friendly refrigerant HFC134a. Therefore, the meth- od of adding, changing or checking the refrigerant is different from the method for CFC12 (Freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty.
Air filtration system
If your vehicle’s air conditioning system is equipped with an air filtration system, replace the filter element according to the replacement schedule shown in the following. This schedule should be fol- lowed to maintain the filter’s dust collec- tion ability. Under extremely dusty condi- tions, the filter should be replaced more frequently. is recommended that you have your filter checked or replaced by your SUBARU dealer. For replacement, use only a genuine SUBARU air filter kit.
It
Replacement schedule:
Every 12 months or 7,500 miles (12,000
km) whichever comes first4-12 Climate control
heated interior. This results in quicker cooling by the air conditioner. Keep the windows closed during the operation of the air conditioner for maximum cooling efficiency.
& Lubrication oil circulation in
the refrigerant circuit
Operate the air conditioner compressor at a low engine speed (at idle or low driving speeds) a few minutes each month during the off-season to circulate its oil.
& Checking air conditioning
system before summer sea- son
Check the air conditioner unit for refriger- ant leaks, hose conditions and proper operation of each spring. Have your SUBARU dealer perform this check.
& Cooling and dehumidifying in
high humidity and low tem- perature weather conditions Under certain weather conditions (high relative humidity, low temperatures, etc.) a small amount of water vapor emission from the air outlets may be noticed. This condition is normal and does not indicate any problem with the air conditioning system.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
& Replacing the air filter
Black plate (159,1)
Climate control 4-13
CAUTION
The arrow mark on the filter must point down.
5. Reinstall the air filter cover.
2. Unhook the hooks of the air filter cover and remove the cover.
1. Remove the glove box. (1) Open the glove box. (2) Remove the nine screws and the one clip securing the glove box. (3) Disconnect connector.
the glove box light
3. Draw out the air filter element. 4. Replace the air filter element with new one.
6. Connect the connector, and reinstall the glove box. 7. Close the glove box.
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (160,1)
4-14 Climate control
1) Service label 2) Caution label
8. LABEL installation
CAUTION
Contact your dealer if the following occurs, even if it is not yet time to change the filter: . Reduction of the air flow through
the vents.
. Windshield gets easily fogged or
misted.
NOTE The filter can influence the air condi- tioning, heating and defroster perfor- mance if not properly maintained.
the information on the
(1) Fill out service label (small). (2) Attach the service label to the driver side door pillar and the caution label the instrument panel.
to the driver side end of
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (9,1)
Audio
Antenna system .................................................. Printed antenna................................................... FM reception ....................................................... Installation of accessories.................................. Audio set ............................................................. Type A audio set ................................................. Type B audio set ................................................. In-dash 6 CD auto changer (Optional audio unit – if equipped)....................................................... Type A audio set (if equipped) ........................... Radio operation...................................................
5-2
5-2
5-2
5-2
5-3
5-3
5-35-3
5-4
5-4Compact disc player operation............................. CD changer control (if optional in-dash CD
changer is connected) .......................................
Type B audio set (if equipped).......................... Radio operation ................................................. Built-in CD changer control................................ Auxiliary unit operation...................................... In-dash 6 CD auto changer (if equipped)......... Loading and unloading compact discs ...............
Precautions to observe when handling a
compact disc...................................................
5-7
5-9
5-11
5-11
5-15
5-20
5-23
5-235-25
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (164,1)
! Wagon and OUTBACK SPORT
Installation of accessories
Always consult your SUBARU dealer before installing a citizen band radio or other transmitting device in your vehicle. Such devices may cause the electronic control system to malfunction if they are incorrectly installed or they are not suited for the vehicle.
if
The antenna is printed on the inner surface of the rear window glass.
& FM reception Although FM is normally static free, reception can be affected by the surround- ing area, atmospheric conditions, station strength and transmitter distance. Build- ings or other obstructions may cause momentary static, flutter or station inter- ference. reception continues to be unsatisfactory, switch to a stronger station.
If
5-2 Audio
Antenna system & Printed antenna
CAUTION
Do not use sharp instruments or window cleaner containing abra- sives to clean the inner surface of the window on which the antenna is printed. Doing so may damage the antenna printed on the window.
! Sedan
The antenna is printed on the inner surface of the rear window glass.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Audio set
& Type B audio set
Your SUBARU may be equipped with one of the following audio sets. See the pages indicated in this section for operating details.
& Type A audio set
Black plate (165,1)
Audio 5-3
& In-dash 6 CD auto changer
(Optional audio unit – if equipped)
. Radio operation: refer to page 5-11
. Built-in CD changer control: refer to page 5-15
. Auxiliary unit operation: refer to page 5- 20. Loading and unloading compact discs: refer to page 5-23
. Radio operation: refer to page 5-4
. Compact disc player operation: refer to page 5-7
. CD changer control: refer to page 5-9北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
5-4 Audio
Type A audio set (if equipped)
The audio set will operate only when the ignition switch is in the “Acc” or “ON” position. & Radio operation
(1) Scan button (2) Power switch, Volume control, Bass/Treble control and Fader/Balance control dial (3) Tuning buttons (4) FM/AM selection button (5) Preset buttons (6) Tone/Balance button
Black plate (166,1)
! Power switch and volume/bass/tre- ble/fader/balance control (ON/VOL) The dial (2) is used for both power (ON/ OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial. ! Tone and balance control (2) normally The volume control dial functions as volume control. This dial becomes a control for Treble, Bass, Fader or Balance when you select the appro- priate audio mode. for each Choose desired volume level mode by turning the volume control dial. The control function returns to volume control mode after approximately 5 sec- onds.
To change control modes: Each brief the “T/B” button (6) changes press of control modes in the following sequence starting from volume control mode. (When the radio is first the control mode is in the volume control.)
turned on,
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Display
Control mode
Black plate (167,1)
Audio 5-5
BAS
TRE
BAL
FAD
VOL
Bass control
Treble control
Balance control
Fader control
Volume control
! FM/AM selection button (FM/AM) Push the “FM/AM” button (4) when the radio is off to turn on the radio. Push the “FM/AM” button when the radio is on to select FM1, FM2 or AM reception. Each time this button is pressed, the band will change in the following order:
Turn counterclockwise
For less bass sound
For less treble sound
Turn clockwise
For more bass sound
For more treble sound
To increase left speaker volume and de-
crease right speaker volume
To increase right speaker volume and
decrease left speaker volume
To increase rear speaker volume and
decrease front speaker volume
To increase front speaker volume and
decrease rear speaker volume
For less volume
For more volume
! Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received.
The display indicates which one is cur- rently selected.
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (168,1)
! Selecting preset stations Presetting a station with a preset button (5) allows you to select that station in a single operation. Up to six AM, FM1 and FM2 stations each may be preset. ! How to preset stations 1. Press the “FM/AM” button (4) to select AM, FM1 or FM2 reception. 2. Press the “SCAN” button (1) or tune the radio manually until the desired station frequency is displayed. 3. Press one of the preset buttons (5) for at least 2 seconds to store the frequency. The frequency of the station will flash once on the display at this time. If the button is pressed for the preceding selection will remain in memory.
less than 2 seconds,
NOTE . If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stations stored in the this preset buttons are cleared. occurs, the preset buttons. . If a cell phone is placed near the radio, it may cause the radio to emit noise when it receives calls. This noise does not indicate a radio fault.
If is necessary to reset
it
5-6 Audio
” side of
! Manual tuning (TUNE) Push the “ ” side of the tuning button (3) to increase the tuning frequency and press the “ the button to decrease it. Each time the button is pressed, the frequency changes 10 kHz in the AM waveband and 0.2 MHz in the FM wave- band. Constant pressure on the button causes a continuous change in the frequency. ! Automatic tuning (SCAN) Press the “SCAN” button (1) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for 5 seconds while displaying the frequency, after which scanning will con- tinue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only. Automatic tuning may not function prop- erly if the station reception is weakened by distance from the station or proximity to tall buildings and hills.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
& Compact disc player operation
(7) Eject button (8) Disc slot (9) Disc button (10) Repeat/Random button (11) Track selection buttons
Black plate (169,1)
Audio 5-7
! To play back a compact disc ! When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it into the slot (with the label side up) and the player will automatically pull the disc into position. An 8 cm/3 inch CD may also be used without any adapter. NOTE . Make sure to always insert a disc with the label side up. . After the last the player will automatically return to track 1 (the first track on the disc). ! When CD is in the player Press the “DISC” button (9). The display will show “CD” and the player will start playback. NOTE After the last track finishes, playback will automatically return to track 1 (the first track on the disc).
track finishes,
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
5-8 Audio
Black plate (170,1)
! To select a track from its beginning ! Forward direction Briefly press the “ ” side of the button (11) to skip to the beginning of the next track. Each time this side of the button is pressed, the indicated track number will increase. ! Backward direction Briefly press the “ ” side of the button (11) to skip to the beginning of the current track. Each time this side of the button is pressed, the indicated track number will decrease. ! Fast-forwarding and fast-reversing ! Fast-forwarding Press the “ continuously to fast-forward the disc. Release the button to stop fast-forwarding. ! Fast-reversing Press the “ continuously to fast-reverse the disc. Release the button to stop fast-reversing. ! Repeat playback Press the “RPT” button (10) while a track is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the
the button (11)
the button (11)
” side of
” side of
repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored. ! Random playback Press the “RDM” button (10) and hold it in more than 2 seconds while a disc is being played back to play all songs on the disc in a random order. The “RDM” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RDM” indicator goes out, and normal playback mode is restored. ! To eject a disc from the player When a disc is being played back or when a disc is in the player, press the eject button “ ” (7). The disc will be ejected. The disc may be removed even when the ignition switch is in the “LOCK” position. NOTE Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
& CD changer control (if optional in-dash CD changer is con-
nected)
An optional CD changer can be connected to this audio unit. Consult the instructions that accompany the CD changer for operating the CD changer itself (e.g., how to load or unload CDs). See your SUBARU dealer for more information.
(12) Track selection buttons (13) Disc button (14) Repeat/Random button (15) Disc selection buttons
Black plate (171,1)
Audio 5-9
! To start playback When the “DISC” button (13) is pressed, the CD changer will start playback. The display shows the current disc number, track number and the elapsed time during playback. NOTE . If a disc is in the player, the “DISC” button is used to change from CD player operation to CD changer opera- tion. Each time the “DISC” button is pressed, the operating mode will change alternately. . At the end of the disc, the player automatically continues with the next disc. . After playback on the last disc finishes, playback will automatically return to the first disc. . If you have loaded fewer than 6
discs, any missing disc is automati- cally skipped.– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
5-10 Audio
! Selection of a desired disc You can select a desired disc from among the discs contained in the CD changer only by pressing the corresponding num- ber on one of the disc selection buttons (15). If you are to listen to the 5th disc in the CD changer, press the “5” button of the disc selection buttons (15). All other discs in the CD changer can also be selected in a similar way. NOTE . No disc change takes place if the button corresponding to the storage tray in which no disc is loaded is pressed. . If the disc selection button (15) corresponding to the disc now in play- back is pressed again, the disc will be replayed from its beginning.
! To select a song from its beginning ! Forward direction Briefly press the “ ” side of the button (12) to skip to the beginning of the next track. Each time this side of the button is pressed, the indicated track number will increase. ! Backward direction Briefly press the “ ” side of the button (12) to skip to the beginning of the current
the disc,
” side of
the button (12)
track. Each time this side of the button is pressed, the indicated track number will decrease. ! Fast-forwarding and fast-reversing ! Fast-forwarding Press the “ continuously to fast-forward the disc. Release the button to stop fast-forwarding. If you continue fast-forwarding to the end of the CD changer will auto- matically stop fast-forwarding and start playback beginning with the first track on the current disc. ! Fast-reversing Press the “ continuously to fast-reverse the disc. Release the button to stop fast-reversing. If you continue fast-reverse to the begin- ning of the CD changer will automatically stop fast-reverse and start playback beginning with the first track on the current disc. ! Repeat playback Use this to play a certain track repeatedly. During playback, press the “RPT” button (14) and release it in less than 2 seconds. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button
the button (12)
” side of
the disc,
Black plate (172,1)
again. Then the “RPT” indicator goes out, and normal playback mode is restored. ! Random playback Use this to play the tracks on the disc in random order. During playback, press the “RDM” button (14) and hold it in for more than 2 seconds. The “RDM” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RDM” indicator goes out, and normal playback mode is restored.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Type B audio set (if equipped)
The audio set will operate only when the ignition switch is in the “Acc” or “ON” position. & Radio operation
Black plate (173,1)
Audio 5-11
(1) Power switch, Volume, Brightness con-
trol dial
(2) FM/AM selection button (3) Seek button (4) Scan button (5) Sound/Tune control dial (6) Preset buttons
! Power switch and volume/bright-
ness control (POWER/VOL/ BRIGHT)
The dial (1) is used for both power (ON/ OFF) and volume control. The radio is turned ON and OFF by pushing the dial, and the volume is controlled by turning the dial. ! Sound control and tune/folder se-
lect/channel control (SOUND/TUNE/ FOLDER/CH)
The dial (5) is used for selecting the sound control mode with each brief press of the dial, and turn it to adjust each level. It is also used for tuning the radio/folder selection (only when playing MP3 or WMA)/channel selection (satellite radio*) when the “FM/AM”, “CD/AUX” and “SAT” are selected. (*: Use of satellite radio (Sirius) requires a tuner, antenna and a service contract. For details, please contact your SUBARU dealer.)
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (174,1)
5-12 Audio
Display
Control mode
BASS
MIDDLE
TREBLE
FADER
BALANCE
VOLUME
Bass control
Midrange control
Treble control
Fader control
Balance control
Volume control
Turn counterclockwise
For less bass sound
Turn clockwise
For more bass sound
For less midrange sound
For more midrange sound
For less treble sound
For more treble sound
To increase rear speaker volume and
decrease front speaker volume
To increase front speaker volume and
decrease rear speaker volume
To increase left speaker volume and de-
crease right speaker volume
To increase right speaker volume and
decrease left speaker volume
For less volume
For more volume
! Sound control The dial (5) controls the Bass, Midrange, Treble, Balance and Fader when you select the appropriate sound control mode. Choose the desired setting for each mode by depressing the “SOUND” control dial function
(5). The control
returns to last mode after approximately 5 seconds.
the “SOUND” control dial
To change control modes: Each brief press of (5) changes control modes in the following sequence starting from bass control mode.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
! Display illumination dimness cance-
lation (BRIGHT)
The brightness of the radio display dims when the light switch is in the “ ” or “ ” position. If this makes the display difficult to read, press the volume dial for more than 2 seconds to return the display to original brightness. Subsequently pressing the volume dial again for more than 2 seconds or if you can safely do so, turning the light switch to the OFF position and back to the “ ” position makes the radio display dim again. ! FM/AM selection button (FM/AM) Push the “FM/AM” button (2) when the radio is on to select FM1, FM2 or AM reception. Each time this button is pressed, the band will change in the following order:
” or “
The display indicates which one is cur- rently selected. ! Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received.
! Manual tuning (TUNE) Turn the tuning dial (5) clockwise to increase the tuning frequency and turn the dial counterclockwise to decrease it. Each click the dial is turned, the frequency changes 10 kHz in the AM waveband and 0.2 MHz in the FM waveband. ! Seek tuning When the “ ” side of the “SEEK/TRACK/ CAT” button (3) is depressed, the radio will begin to automatically seek up for recei- vable frequencies and will stop at the first one found. For the “ ” side, the radio will begin to automatically seek down. This function may not be available, however, when radio signals are weak. In such a situation, perform manual tuning to select the desired station. ! Automatic tuning (SCAN) Press the “SCAN” button (4) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at a receivable station for 5 seconds while displaying the frequency by blinking, after which scanning will continue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for
Black plate (175,1)
Audio 5-13
automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only. Automatic tuning may not function properly if the station recep- tion is weakened by distance from the station or proximity to tall buildings and hills. ! Selecting preset stations Presetting a station with a preset button (6) allows you to select that station in a single operation. Up to six AM, FM1 and FM2 stations each may be preset. ! How to preset stations 1. Press the “FM/AM” button (2) to select AM, FM1 or FM2 reception. 2. Press the “SCAN” button (4) or tune the radio manually until the desired station frequency is displayed. 3. Press one of the preset buttons (6) for at least 2 seconds to store the frequency. The frequency of the station will flash once on the display at this time.
NOTE . If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stations stored in the this preset buttons are cleared. occurs, the – CONTINUED –
If is necessary to reset
it
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (176,1)
5-14 Audio
preset buttons. . If a cell phone is placed near the radio, it may cause the radio to emit noise when the phone receives calls. This noise does not indicate a problem with the radio.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
& Built-in CD changer control
Black plate (177,1)
Audio 5-15
(7) CD button (8) Eject button (9) Disc slot (10) Track selection buttons (11) Repeat/Random button (12) Disc number indicator (13) Load button (14) Folder selection dial (15) Disc selection buttons (16) Display button
NOTE . Make sure to always insert a disc with the label side up. . If a disc is inserted during a radio broadcast, the disc will interrupt the broadcast. . The player is designed to be able to play music CD-Rs and music CD-RWs, but it may not be able to play certain ones. . 8 cm/3 inch CDs are not supported, and if inserted, they will be immediately ejected.
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (178,1)
5-16 Audio
it means that
! How to insert a CD(s) ! Inserting a CD 1. Briefly press the “LOAD” button (13). If the magazine in the player has an idle position where you can insert a disc, the disc number indicator associated with the If no indicator idle position will blink. blinks, there is no idle position in the magazine. 2. When “IN” is displayed, insert the disc. Once you have inserted the disc, the disc number indicator will stop blinking. The disc will be then automatically drawn in, and the player will begin to play back the first track of the disc. . To insert more discs in succession, repeat Steps 1 and 2. The magazine will be loaded with discs in the ascending order of position number. If you do not insert any disc within 15 seconds after you have pressed the “LOAD” button and “IN” is displayed, the player will begin to play back the first track of the last disc you have inserted. . While the player is in the loading mode, if you press the “FM/AM” button (2), the player will enter the standby mode. Press the “CD/AUX” button (7) to start playback.
! Inserting a disc in a desired position 1. Briefly press the “LOAD” button (13). If the magazine in the player has an idle position where you can insert a disc, the disc number indicator (12) associated with the idle position will blink. 2. Press the disc selection button (15) at the position where you want to insert a disc. The associated disc number indica- tor will blink. 3. If you insert a disc during the 15- second period while “IN” is displayed, the disc will be automatically drawn in, and the player will start playback of the disc, beginning with the first track. . To insert more discs in succession, repeat Steps 1 and 3. . While the player is in the loading mode, if you press the “FM/AM” button (2), the player will enter standby mode. Press the “CD/AUX” button (7) to start playback. ! Loading all the magazine (Full disc
loading mode) If you continue to press the “LOAD” 1. button (13) for more than 2 seconds, the player will enter the full disc loading mode. 2. The disc number indicator (12) asso- ciated with the idle position will blink. The magazine will be loaded with discs in the ascending order of position number.
3. When the loading of a disc is com- plete, the next disc number indicator (12) will blink. Then repeat Step 2. 4. When the magazine is filled with discs by repeating Steps 2 and 3, the player will start playback of the discs, beginning with the one inserted first. If you fail to insert any disc during each 15 seconds interval, the full disc loading mode will be can- celed, and the player will start playback of the disc inserted first.
! How to play back a CD or make a
pause
! When there is no CD inserted: Insert a CD by referring to “How to insert a CD(s)”. When a CD is loaded, the player will start playback of the CD, beginning with the first track. ! When there are CDs loaded: Depress the “CD/AUX” button to turn on the CD (when the last mode of the player is CD) and press a desired one of the disc selection buttons (15). The player will then start playback of the selected CD, begin- ning with the first track.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
! To select a track from its beginning ! Forward direction Briefly press the “ ” side of the button (10) to skip to the beginning of the next track. Each time the button is pressed, the indicated track number will increase. ! Backward direction Briefly press the “ ” side of the button (10) to skip to the beginning of the current track. Each time the button is pressed, the indicated track number will decrease. ! To select a folder (for MP3/WMA
audio)
” side of
Turn the “TUNE/FOLDER/CH” dial (14) to select the folder. ! Fast-forwarding and fast-reversing ! Fast-forwarding Press the “ the button (10) continuously to fast-forward the disc. Release the button to stop fast-forwarding. ! Fast-reversing Press the “ the button (10) continuously to fast-reverse the disc. Release the button to stop fast-reversing. ! Repeat playback Depress the “RPT/RDM” button (11) while a song is playing to play the song
” side of
repeatedly. Each time this button is pressed, the repeat play mode will change in the following order:
The “RPT” indicator will come on and the song will be played continuously. When the “RPT” the repeat OFF is selected, indicator goes out and normal playback mode is restored. . The repeat play mode will be can- celed if you perform any of the follow- ing steps: . Press the “RPT/RDM” button to select the repeat OFF. . Press the eject button. . Press the “LOAD” button. . Select the radio mode. . Turn the “TUNE/FOLDER/CH” dial (for MP3/WMA audio). . Turn off equipment. . Turn the ignition switch to the “OFF” position. ! Random playback Press the “RPT/RDM” button (11) for more than 2 seconds while a disc is being played back to play all songs on the disc in
the power of
the audio
Black plate (179,1)
Audio 5-17
a random order.
The “RDM” indicator will come on and all songs on the disc will be played in a random order. When the random OFF is the “RDM” indicator goes out selected, and normal playback mode is restored. . The random play mode will be canceled if you perform any of the following steps: . Press the “RPT/RDM” button to select the random OFF. . Press the eject button. . Press the “LOAD” button. . Select the radio mode. . Turn the “TUNE/FOLDER/CH” dial (for MP3/WMA audio). . Turn off equipment. . Turn the ignition switch to the “OFF” position. ! How to unload CDs from the player ! Ejecting a CD from the player Of the discs loaded, you can select and remove only one disc. 1. Press the disc selection button (15) of the disc whose disc number indicator (12) is ON. 2. Press the eject button (8). Then the – CONTINUED –
the power of
the audio
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
5-18 Audio
disc number indicator associated with the disc you have selected will blink, and the disc will be ejected. To remove more discs in succession, repeat Steps 1 and 2. If you press the eject button after turning OFF the ignition switch, only one disc will be ejected.
! Ejecting all discs from the player (All
disc ejection mode) 1. If you continue to press the eject button (8) for more than 2 seconds, the player will enter the all disc ejection mode. 2. Remove the disc that has been the display indicates “CD ALL ejected, EJECT” (when the ignition switch is in the “Acc” or “ON” position) and disc indicator will blink. The other discs loaded will then be ejected one after another. If you do not remove the ejected disc within 15 sec- onds, the “All disc ejection mode” will be canceled.
NOTE Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out.
CAUTION
Do not attempt to insert two or more
discs into the slot at a time. Doing so can cause mechanical damage to the CD changer.
! Title display selection If you briefly press the “DISP” button (16) during playback, the indication will change to the next one in the following sequence. . For MP3/WMA:
. For Satellite radio:
The display mode that you selected will not be changed until you select the display mode again. When you depress the “DISP” button for more than 2 seconds, the title will be scrolled so you can see all of it. You will see 12 characters at a time. . The page scroll mode will be can- celed if you perform any of the follow- ing steps: . When you do not operate any button within 10 seconds. . Press any button to select another
Black plate (180,1)
” or “
” button.
play mode. . Press the eject button. . Press the disc selection button. . Select the radio mode. . Press the “ . Turn off equipment. . Turn the ignition switch to the “OFF” position. NOTE When the disc has no title, the display indicates “NO TITLE”.
the power of
the audio
! When the following messages are
displayed
If one of the following messages is displayed while operating the CD player, determine the cause based on the follow- ing information. If you cannot clear those messages, please contact your SUBARU dealer. ! When “PUSH EJECT” is displayed This message means that there is a mechanical error. Depress the eject button to unload the disc. Check the disc for damage or deformation, and also check that the correct disc is inserted. Do not try to unload the disc forcibly. 8 cm/3 inch CDs are not supported, and if inserted, they will be immediately ejected and this
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
error message will be displayed. If the disc cannot be unloaded or the error message remains displayed, please contact your SUBARU dealer. ! When “CHECK DISC” is displayed Press the eject button to unload the discs. Check that the disc is not damaged or scratched, and also check that the disc is inserted correctly. Some CD-RW discs may be causing this error message to appear. Check that the disc type (i.e., 8
cm/3 inch CDs are not supported) and data format are correct. This player can only play MP3 and WMA data formats. If the disc cannot be unloaded or the error message remains displayed, please con- tact your SUBARU dealer.Black plate (181,1)
Audio 5-19
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
5-20 Audio
& Auxiliary unit operation
Black plate (182,1)
(17) AUX button (18) Category button (19) Scan button (20) Satellite radio* button (21) Category selection button (22) Preset buttons (23) Channel selection dial
(*: Use of satellite radio (Sirius) requires a tuner, antenna and a service contract. For details, please contact your SUBARU dealer.) “Satellite Radio mode” and “AUX mode” are available as well as the CD changer mode when the unit is in the Auxiliary unit mode. NOTE . For use of the In-dash CD changer, refer to the section of “In-dash 6 CD auto changer” in this chapter. . Use of satellite radio (Sirius) re- quires a tuner, antenna and a service contract. For details, please contact your SUBARU dealer. . The “AUX mode” can be used when the appropriate device is connected to the AUX terminal. . The output sound of the portable audio player is not loud, and the sound via the vehicle’s speakers that are connected to the vehicle audio set is very quiet. If you turn up the volume of
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
the audio set, the volume becomes louder. However, when you change the audio to the radio mode or to a CD player, the sound becomes a lot louder. Remember to turn down the volume when you change between them.
! AUX terminal (if equipped) The AUX terminal is located behind the lid under the climate controls. Push gently on the lid to open it.
Black plate (183,1)
Audio 5-21
NOTE Use of satellite radio (Sirius) requires a tuner, antenna and a service contract. For details, please contact your SUBARU dealer. or Visit Sirius Satellite Radio at sirius.com or call 1-888-539-SIRIUS (7474) for more information. Sirius, the Sirius dog logo, channel names and logos are trademarks of SIRIUS Satellite Radio Inc. ! Satellite radio reception Satellite radio signals are best received in areas with a clear view of the open sky. In areas where there are tall buildings, trees, tunnels or other structures that may obstruct the signal of the satellites, there may be signal interruptions. Other circum- stances that may result loss include driving near a wall, steep cliff or hill, or driving on the lower level of a multi- tiered road or inside a parking garage.
in signal
To help reduce this condition, satellite radio providers have installed ground- based repeaters in heavily populated areas. However, you may still experience reception problems in some areas.
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
! Satellite Radio mode Press the “SAT” button (20) to select the “Satellite radio mode” (when the SR-BB is connected).
5-22 Audio
! Displaying Sirius ID of tuner When you activate Sirius, you should have your Sirius tuner ID ready because each tuner is identified by its unique Sirius tuner ID. The Sirius ID will be needed when you activate Sirius and receive Sirius custo- mer support. The Sirius ID can be found on the audio display by tuning the channel to “0”. Turn the “TUNE/FOLDER/CH” dial (23) to select the satellite radio channel. ! Channel selection Turn the “TUNE/FOLDER/CH” dial (23) to select the radio channel. Turn the tuning dial clockwise to change the channel upward and turn the dial counterclockwise to change the channel downward with each click of the dial. ! Category selection Press the “SEEK/TRACK/CAT” button (18) radio channel. Press the “ ” side of the button (18) to change the category upward and the “ ” side of the button to downward with each press of the button. ! Channel preset Presetting a channel with a preset button (22) allows you to select that station in a single operation. Up to six SR1, SR2 and
the category of
to select
SR3 channels each may be preset. Press one of the preset buttons for at least 2 seconds to store the channel. The number of the channel will flash once on the display, and the unit produces a beep sound at this time. ! Channel scan Press the “SCAN” button (19) to change the radio to the SCAN mode. In this mode, the radio scans through the channel until a station is found. The radio will stop at the station for 5 seconds while displaying the channel number, after which scanning will continue until the entire channel has been scanned from the low end to the high end. Press the “SCAN” button (19) again to cancel the SCAN mode and to stop on any displayed station. When the “SCAN” button is pressed for automatic tuning, stations are only scanned in an upward direction. ! Category mode Press the “CAT” button (21) for at least 2
seconds to turn the category mode on. In this mode, the radio operations (channel selection, channel scan) are performed only in the selected category. To cancel the category mode, press the “CAT” button (21) for at least 2 seconds again.Black plate (184,1)
! Band selection Push the “SAT” button (20) when the radio is on to select SR1, SR2 or SR3 reception. Each time this button is pressed, the band will change in the following order:
! AUX mode Press the “CD/AUX” button (17) to select the “AUX mode” (when the AUX unit is connected to the AUX terminal).
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
In-dash 6 CD auto changer (if equipped) & Loading and unloading compact discs
Black plate (185,1)
Audio 5-23
CAUTION
. Do not attempt to insert two or more discs into the slot at a time. Doing so can cause mechanical damage to the CD changer.
. Use only music CDs identified by
mark.
. Do not use CDs listed in the following which could cause da- mage to the CD player. . 3 inch (8 cm) compact disc . Any disc with a peel-off or seal
on it
. Any disc with scratches and/
or dust
. Bent disc . Cleaning disc . CD accessory (e.g., 3 inch (8
cm) disc adapter)
. Do not insert or remove any disc when the automatic transmission selector lever is in the park position; the selector lever in that position can interfere with disc insertion or removal, causing scratches on the disc surface (for AT vehicles).
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
(1) Disc slot (2) Disc indicators (disc No. 1 to 6) (3) Disc selection buttons (disc No. 1 to 6)
(4) Eject button (5) Disc slot indicator
5-24 Audio
! To insert a disc 1. Press one of the disc selection buttons (3) (numbered from 1 to 6) for which the disc indicator light (2) is off. The disc indicator lights are located directly above the corresponding disc selection buttons. 2. The indicator will begin blinking. The blinking will last for 15 seconds. During this period, insert a desired disc, and the disc will begin to play. (If any disc is not inserted during this period, the disc slot (1) door will close. Repeat Step 1.) Be sure to hold a disc with the label side (the side where titles are printed) up. 3. To insert another disc, repeat Steps 1
and 2 choosing a different disc selection button.! To insert six discs at a time 1. Press and hold the disc selection button (3) number 1 until all disc indicators begin blinking (approximately 1.5 sec- onds). 2. The indicators will blink for 15 sec- onds. During this period, insert six discs. 3. When all discs are loaded, the first disc will begin to play. (If no disc is inserted within this 15 seconds, the entire disc load sequence will be canceled.)
! To remove a disc 1. Press the desired disc selection button (3) (numbered from 1 to 6) for which the disc indicator light is on. 2. Press the eject button “ ” (4). The selected disc will be ejected and the indicator light will begin blinking. 3. To remove another disc, repeat Steps 1 and 2 choosing a different disc selection button. (To remove discs when the ignition switch is in the “LOCK” position, press the eject button “ ”, and the first disc will be ejected. Press the eject button “ ” again, and the next disc will be ejected and so on. At this time, the disc selection buttons are disabled.)
! To remove all discs at one time 1. Press and hold the eject button “ ” (4) until all disc indicators begin blinking (approximately 1.5 seconds), and the first disc will be ejected. 2. When the disc is removed, the next one will be ejected, and so on.
! To replace a playing disc with
another
Simply press the desired one of disc selection buttons (3) (numbered from 1
Black plate (186,1)
to 6) or press the disc selection button on the radio unit to select the desired disc, and the disc will begin to play. ! Disc indicators Lit: when the corresponding storage tray is occupied by a disc. Blinking: Disc player is either in loading, eject or changing mode. OFF: No disc is loaded or the ignition switch is in the “LOCK” position. ! Open/Closed disc slot indicator When the disc slot is open, indicators on both sides of illuminate. ! Function control Refer to CD changer control operating instructions described in the “Type A audio set” or “Type B audio set” section.
the disc the slot
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Precautions to observe when handling a compact disc
Use only compact discs (CDs) that have the mark shown in the following illustra- tion.
You may also use compact discs (CD-Rs and CD-RWs) that have the following marks, but you may not use some discs if they were produced using writing meth- ods not compatible with your vehicle’s audio system.
. You cannot use a DualDisc in the CD player. If you insert a DualDisc into the player, the disc may not come out again, possibly causing the player to malfunction. . In cold and/or rainy weather, dew can form inside the CD player, preventing
Black plate (187,1)
Audio 5-25
If
normal operation. this happens, eject the CD and wait for the player to dry out. . Skipping may occur when the CD player is subjected to severe vibration (for example, when the vehicle is driven on a rough surface). . To remove a disc from the case, press the center of the case and hold both edges of the disc. If the disc surface is touched directly, contamination could cause poor tone quality. Do not touch the disc surface. . Use a clean disc whenever possible. If there are deposits, wipe the disc surface from the center outward with a dry, soft cloth. Be sure not to use a hard cloth, thinner, benzine, alcohol, etc. . Do not use any disc that is scratched, deformed, or cracked. Also, do not use any disc that has a non-standard shape (for example, a heart shape). Malfunctions or problems might result. . A disc is vulnerable to heat. Never keep it either in places exposed to direct sunlight, near heaters or in vehicles parked in the sun or on hot days.
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
5-26 Audio
Black plate (188,1)
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Interior lights ....................................................... Dome light .......................................................... Cargo area light (if equipped) .............................. Map light (if equipped)........................................ Sun visors ........................................................... Vanity mirror (if equipped) ................................... Storage compartment ......................................... Glove box ........................................................... Center console.................................................... Coin tray............................................................. Pocket (if equipped) ............................................ Cup holders ......................................................... Front passenger’s cup holder .............................. Rear passenger’s cup holder (if equipped) ...........
6-2
6-2
6-2
6-2
6-3
6-3
6-4
6-4
6-4
6-4
6-5
6-5
6-5
6-6Black plate (11,1)
Interior equipment
Accessory power outlets ....................................
6-6
Use with a cigarette lighter
(Canada only, if equipped).................................. Ashtray (Canada only, if equipped) .................... Floor mat (if equipped)........................................ Coat hooks........................................................... Cargo area cover (Wagon – if equipped) ......... Using the cover ................................................. To remove the cover .......................................... Stowage of the cover ......................................... To install the cover housing ...............................
Cargo tie-down hooks
(Wagon – if equipped) .................................... Cargo area bars (Wagon) .................................. Under-floor storage compartment
(Wagon – if equipped) ....................................
6-7
6-8
6-9
6-9
6-10
6-10
6-10
6-11
6-116-11
6-126-12
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (190,1)
6-2 Interior equipment
Interior lights
When leaving your vehicle, make sure the light goes out to avoid battery discharge.
& Dome light
tion in chapter 2 for detailed information. OFF: The light stays off.
& Cargo area light (if equipped)
Map light (if equipped)
The dome light switch has three positions:
ON: The light stays on continuously. DOOR (middle position): The light comes on when any of the doors (or the rear gate on wagon) is opened. The light remains on for several seconds and gradually goes out after all doors (and the rear gate on the wagon) are closed or if the key is turned to the “ON” position. The light also can be turned on by use of the remote keyless entry transmitter. See the “Remote keyless entry system” sec-
Vehicle with moonroof
DOOR: The light comes on only when the rear gate is opened. OFF: The light stays off.
Vehicle without moonroof
To turn on the map light, push the switch. To turn it off, push the switch again.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
When leaving the vehicle, make sure the light to avoid battery dis- charge.
is turned off
Sun visors
Black plate (191,1)
Interior equipment 6-3
& Vanity mirror (if equipped)
CAUTION
Keep the vanity mirror cover closed while the car is being driven to avoid dazzle.
To block out glare, swing down the visors. To use the sun visor at a side window, swing it down and move it sideways.
To use the vanity mirror, swing down the sun visor and open the vanity mirror cover.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (192,1)
6-4 Interior equipment
Storage compartment
& Glove box
& Center console
CAUTION
. Always keep the storage com- partment closed while driving to reduce the risk of injury in the event of a sudden stop or an accident.
. Do not store spray cans, contain- ers with flammable or corrosive liquids or any other dangerous items in the storage compart- ment.
Lock
1) 2) Unlock
To open the glove box, pull the handle. To close it, push the lid firmly upward.
To lock the glove box, insert the key and turn it clockwise.
To open the lid, pull up the lock release.
& Coin tray
To open the coin tray, pull the upper edge
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (193,1)
Interior equipment 6-5
of the lid.
& Pocket (if equipped)
Cup holders
CAUTION
Take care to avoid spills. Beverages, if hot, might burn you or your passengers. Spilled beverages may also damage upholstery, carpets or audio equipment.
& Front passenger’s cup holder
CAUTION
A dual cup holder is built in the center console, beside the parking brake lever.
Do not pick up a cup from the cup holder or put a cup in the holder while you are driving, as this may distract you and lead to an accident.
CAUTION
Do not use the pocket as an ashtray or leave a lighted cigarette in the pocket. This could cause a fire.
To use the pocket, push lightly on the lid below the climate controls.
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
6-6 Interior equipment
& Rear passenger’s cup holder
(if equipped)
Accessory power outlets
CAUTION
When not in use, always keep the cup holder stored while driving to reduce the risk of injury in the event of a sudden stop or an accident.
Power outlet beside front pocket
A dual cup holder is located at the back of the center console. To use the cup holder, open the lid by pulling its upper edge.
Power outlet in cargo area (if equipped)
Accessory power outlets are provided beside the front pocket and in the cargo
Black plate (194,1)
area. Electrical power (12V DC) from the battery is available at any of the outlets when the ignition switch is in either the “Acc” or “ON” position. You can use an in-car electrical appliance by connecting it to an outlet. The maximum power rating of an appli- ance that can be connected varies among outlets as shown in the following. Do not use an appliance which exceeds the indicated wattage for each outlet. Outlet beside front pocket: 80W or less Outlets in cargo area: 120W or less When using appliances connected to two outlets simultaneously, the total power consumed by them must not exceed 120W.
CAUTION
. Do not attempt to use a cigarette lighter in the cargo area power outlet.
. Do not place any foreign objects, especially metal ones such as coins or aluminum foil, into the accessory power outlet. That could cause a short circuit. Al- ways put the cap on the acces- sory power outlet when it is not in use.
. Use only electrical appliances
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
which are designed for 12V DC. The maximum power rating of an appliance that can be connected varies among outlets as shown in the following. Do not use an appliance which exceeds the in- dicated wattage for each outlet. Outlet beside front pocket: 80W or less Outlet less When using appliances con- nected to two outlets simulta- neously, the total power con- sumed by them must not exceed 120W. Overloading the accessory power outlet can cause a short circuit. Do not use dual adapters or more than one electrical appli- ance.
in cargo area: 120W or
. If the plug on your electric appli- ance is either too loose or too tight for the accessory power outlet, this can result in a poor contact or cause the plug to get stuck. Only use plugs that fit properly.
. Use of an electric appliance in the accessory power outlet for a long period of time while the engine is not running can cause battery
discharge.
. Before driving your vehicle, make sure that the plug and the cord on your electrical appliance will not interfere with your shifting gears and operating the accel- erator and brake pedals. If they do, do not use the electrical appliance while driving.
& Use with a cigarette lighter (Canada only, if equipped)
To use the accessory power outlet beside the front pocket as a cigarette lighter socket, purchase the cigarette lighter plug, which is an optional accessory. A cigarette lighter plug is available from
Black plate (195,1)
Interior equipment 6-7
your SUBARU dealer. The cigarette lighter operates only when the ignition switch is in the “ON” or “Acc” position. To use the cigarette lighter, push in the knob and wait a few moments. It will automatically spring up when ready for use.
WARNING
To avoid being burned, never grasp the lighter by the end with the heating element. Doing so could result in injury and could also damage the heating element.
CAUTION
. Do not hold the lighter pushed in,
because it will overheat.
. The electrical power socket lo- cated on the lower part of the instrument panel is originally de- signed to use a genuine SUBARU cigarette lighter plug. Do not use a non-genuine cigarette lighter plug in the socket. Doing so may cause a short-circuit and overheating, resulting in a fire.
. If the socket is ever used for a
– CONTINUED –
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (196,1)
6-8 Interior equipment
plug-in accessory such as a cell phone, that may damage the portion of the socket’s internal mechanism that causes a cigar- ette lighter plug to “pop out” after its lighter element is heated. Therefore, do not place a cigar- ette lighter plug in a socket that has been used, even once, to power a plug-in accessory. Doing so may cause the plug to stick and overheat, creating a potential fire hazard.
Ashtray (Canada only, if equipped)
CAUTION
Do not use ashtrays as waste re- ceptacles or leave a lighted cigarette in an ashtray. This could cause a fire.
To remove the ashtray for cleaning, hold the right and left sides of the ashtray and pull it out. NOTE
It is possible to install an ashtray, which is an optional accessory, in the front pocket. The ashtray is available from your SUBARU dealer. To open the ashtray, push lightly on the lid below the climate controls. Fully close the lid after using it to help reduce residual smoke.
Particles of ash and tobacco will accu- mulate around the hinges of the ash- tray’s inner lid. Clean them off using a toothbrush or other narrow-ended im- plement.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Floor mat (if equipped)
Coat hooks
Black plate (197,1)
Interior equipment 6-9
A retaining pin is located on the driver’s side of the vehicle next to the fuel filler door release. The floor mat is secured using the built-in grommet, by placing the grommet over the pin and pushing downward.
CAUTION
Make sure the driver’s floor mat is placed back in its proper location and correctly secured on its retain- ing pin. If the floor mat slips forward and interferes with the movement of the pedals during driving, it could cause an accident.
The coat hook is attached to the rear left and rear right passenger’s hand grip.
CAUTION
Never hang anything on the coat hook that might obstruct the driver’s view or that could cause injury in a sudden stop or in a collision. And do not hang items on the coat hook that weigh 2.2 lbs (1 kg) or more.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
Black plate (198,1)
& To remove the cover 1. Rewind the cover.
2. Pull either sleeve on the end of the cover housing to shorten the cover’s length. 3. Take it off the retainer.
WARNING
Do not place anything on the ex- tended cover. Putting excessive weight on the extended cover can break it and an object on the cover could tumble forward in the event of a sudden stop or collision. This could cause serious injury.
CAUTION
Be careful not to scratch the rear gate stays while extending and rewinding the cover. Scratches on the stays could cause leakage of gas from the stays, which may result in their inability to hold the rear gate open.
6-10 Interior equipment
Cargo area cover (Wagon – if equipped)
The cargo area cover is provided for covering the cargo area and to protect its contents from direct sunlight. This cover is detachable to make room for additional cargo.
& Using the cover
To extend the cover, pull the end of the cover out of the housing, then insert its hooks into the catches as shown. To rewind it, unhook it from the catches and it will rewind automatically. You should hold on to the cover and guide it back into the cover housing while it is rewinding.
北米Model "A1920BE-B" EDITED: 2006/ 9/ 19
& Stowage of the cover
& To install the cover housing 1. Pull either sleeve on the end of the cover housing to shorten the cover’s length.
Black plate (199,1)
Interior equipment 6-11
Cargo tie-down hooks (Wa- gon – if equipped)
For the vehicles equipped with an under- floor storage compartment, the cargo area cover can be stowed under the cargo floor.
