Download PDF Manual

(21 seconds after turning ON the ignition switch), the warning lights will alternate between flashing and steady illumination at 15-second intervals, and the chime will sound while the warning light is flashing. Alternate flashing and steady illumination of the warning lights and sounding of the chime will continue until the driver fastens the seatbelt.


Black plate (124,1)


NOTE . If the driver unfastens the seatbelt after fastening, the seatbelt warning device operates as follows according to the vehicle speed.


. At speeds lower than approxi- mately 9 mph (15 km/h) The warning light will alternate between flashing and steady illumi- nation at 15-second intervals. The chime will not sound. . At speeds higher than approxi- mately 9 mph (15 km/h) The warning light will alternate between flashing and steady illumi- nation at 15-second intervals and the chime will sound while the warning light is flashing.


. It is possible to cancel the warning operation that follows the 6-second warning after turning ON the ignition switch. When the ignition switch is the turned ON next complete sequence of the warning operation resumes. For further details about canceling the warning operation, please contact your SUBARU dealer.


time, however,


& SRS airbag system


warning light


When the ignition switch is turned to the


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


“ON” position, the SRS airbag system warning light will come on for approxi- mately 6 seconds and go out. This shows the SRS airbag and SRS side airbag (if equipped) and seatbelt pretensioners are in normal operation.


WARNING


If the warning light exhibits any of the following conditions, there may be a malfunction in the seatbelt pretensioners and/or SRS airbag system. Immediately take your vehi- cle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS airbag will not operate properly in the event of a collision, which may increase the risk of injury. . Flashing or flickering of the warn-


ing light


. No illumination of


the warning light when the ignition switch is first turned to the “ON” position the


. Continuous illumination of


warning light


. Illumination of the warning light


while driving


& Front passenger’s frontal


airbag ON and OFF indica- tors


ON or


or


: Front passenger’s frontal airbag ON indicator : Front passenger’s frontal airbag OFF indicator


The front passenger’s frontal airbag ON and OFF indicators show you the status of the front passenger’s SRS frontal airbag. The indicators are located next to the clock in the center portion of the dash- board. When the ignition switch is turned to the “ON” position, both the ON and OFF indicators illuminate for 6 seconds during which time the system is checked. Follow- ing the system check, both indicators


Black plate (125,1)


Instruments and controls 3-15


extinguish for 2 seconds. After that, one of the indicators illuminates depending on the status of the front passenger’s SRS frontal airbag determined by the Subaru advanced frontal airbag system monitor- ing. If the front passenger’s SRS frontal airbag is activated, the passenger’s frontal airbag ON indicator will illuminate while the OFF indicator will remain extinguished. If the front passenger’s SRS frontal airbag the passenger’s frontal is deactivated, airbag ON indicator will remain extin- guished while the OFF indicator will illuminate. With the ignition switch turned to the “ON” position, if both the ON and OFF indica- tors remain lit or extinguished simulta- neously even after the system check period, the system is faulty. Contact your SUBARU dealer immediately for an in- spection.


– CONTINUED –


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


3-16 Instruments and controls


& CHECK ENGINE warn- ing light/Malfunction in- dicator lamp


CAUTION


If the CHECK ENGINE light comes on while you are driving, have your vehicle checked/repaired by your SUBARU dealer as soon as possi- ble. Continued vehicle operation without having the emission control system checked and repaired as necessary could cause serious da- mage, which may not be covered by your vehicle’s warranty.


If this light comes on steadily or blinks while the engine is running, it may indicate that there is a problem or potential problem somewhere in the emission con- trol system. ! If the light comes on steadily: If the light comes on steadily while driving or does not go out after the engine starts, an emission control system malfunction has been detected. You should have your vehicle checked by an authorized SUBARU dealer immedi- ately.


NOTE This light also comes on when the fuel filler cap is not tightened until it clicks. If you have recently refueled your vehicle, the cause of the CHECK ENGINE warning light/malfunction indicator lamp coming on could be a loose or missing fuel filler cap. Remove the cap and retighten it until it clicks. Make sure nothing is interfering with the sealing of the cap. Tightening the cap will not make the CHECK ENGINE warning light turn off immediately. It may take several driving trips. If the light does not go out, take your vehicle to your authorized SUBARU dealer immediately. ! If the light is blinking: If is blinking while driving, an engine misfire condition has been de- tected which may damage the emission control system. To prevent serious damage to the emis- sion control system, you should do the following. . Reduce vehicle speed. . Avoid hard acceleration. . Avoid steep uphill grades. . Reduce the amount of cargo, if possi- ble. . Stop towing a trailer as soon as possible.


the light


Black plate (126,1)


The CHECK ENGINE warning light may stop blinking and come on steadily after several driving trips. You should have your vehicle checked by an authorized SUBARU dealer immediately. & Charge warning light If this light comes on when the engine is running, it may indicate that the charging system is not working properly.


If the light comes on while driving or does not go out after the engine starts, stop the the first safe opportunity and engine at check the alternator belt. is the belt loose, broken or if is in good condition but the light remains on, contact your nearest SUBARU dealer immedi- ately. & Oil pressure warning


If the belt


light


If this light comes on when the engine is running, it may indicate that the engine oil pressure is low and the lubricating system is not working properly. If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the engine oil level. If the oil level is low, add oil immediately. If the engine oil is at the proper level but the light remains on,


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


contact your nearest SUBARU dealer immediately.


CAUTION


Do not operate the engine with the oil pressure warning light on. This may cause serious engine damage.


er for service immediately. & Rear differential oil


temperature warning light (WRX-STI)


CAUTION


& AT OIL TEMPerature


warning light (AT vehi- cles)


The AT oil temperature warning light comes on when the ignition switch is turned to the “ON” position and goes out after the engine has started. If this light comes on when the engine is running, it may indicate that the automatic transmission fluid temperature is too hot.


If the light comes on while driving, it is unnecessary to stop the vehicle, but avoid driving up steep grades or in stop and go traffic. ! Automatic transmission control


system warning


If the light flashes after the engine starts, it may indicate that the automatic transmis- sion control system is not working prop- erly. Contact your nearest SUBARU deal-


Reduce vehicle speed and park the vehicle in a safe place as soon as possible if the R.DIFF TEMP light comes on. Continued driving with this light on can damage the rear differential and other parts of the powertrain.


it may indicate that


If this light comes on when the engine is running, the rear differential oil temperature is too hot. the driver’s control center At differential will automatically cancel the current torque-distribution ratio setting and adopts its minimum ratio.


this time,


If the light comes on while driving, reduce vehicle speed and stop the vehicle at the nearest safe place. Park the vehicle for several minutes. After the light goes out, you can start driving. If the light does not go out, contact the nearest SUBARU dealer for service.


Black plate (127,1)


Instruments and controls 3-17


NOTE . If the tire pressures are not correct and/or the tires are not all the same size and brand, the rear differential will be heavily loaded when the vehicle is driven, resulting in an abnormally high oil temperature. . The rear differential oil will deterio- rate if its temperature increases en- ough for the rear differential oil tem- perature warning light to come on. It is advisable to have the rear differential oil replaced as soon as possible.


& ABS warning light The ABS warning light comes on when the ignition switch is turned to the “ON” position and goes out after approximately 2 seconds. This is an indication that the ABS system is working properly.


CAUTION


If the warning light behaves as follows, the ABS system may not work properly. When the warning light is on, the ABS function shuts down; however, the conventional brake system con- tinues to operate normally.


– CONTINUED –


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


3-18 Instruments and controls


. The warning light does not come on when the ignition switch is turned to the “ON” position.


. The warning light comes on when the ignition switch is turned to the “ON” position, but it does not go out even when the vehicle speed exceeds approximately 8
mph (12 km/h).


. The warning light comes on dur-


ing driving.


If any of these conditions occur, have the ABS system repaired at the first available opportunity by your SUBARU dealer.


With a vehicle equipped with an EBD system, the ABS warning light comes on together with the brake system warning light if the EBD system becomes faulty. For further details of the EBD system fault warning, refer to “Brake system warning light”. NOTE If described in the following, system may be considered normal. . The warning light comes on right after the engine is started but goes out immediately, remaining off. . The warning light remains on after


the warning light behavior is as the ABS


the engine has been started, but it goes out when the vehicle speed reaches approximately 8 mph (12 km/h). . The warning light comes on during driving, but it goes out immediately and remains off. When driving with an insufficient battery voltage such as when the engine is jump started, the ABS warning light may come on. This is due to the low battery voltage and does not indicate a malfunction. When the battery becomes fully charged, the light will go out. & Brake system warning


light


WARNING


. Driving with the brake system warning light on is dangerous. This indicates your brake system may not be working properly. If the light remains on, we recom- mend that you have the brakes inspected by a SUBARU dealer immediately.


. If at all in doubt about whether the brakes are operating prop- erly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for re-


Black plate (128,1)


pair.


This light has the following three functions: ! Parking brake warning The light comes on with the parking brake applied while the ignition switch is in the “ON” position. It goes out when the parking brake is fully released. ! Brake fluid level warning This light comes on when the brake fluid level has dropped to near the “MIN” level of the brake fluid reservoir with the ignition switch in the “ON” position and with the parking brake fully released.


If


this occurs,


If the brake system warning light should come on while driving (with the parking brake fully released and with the ignition switch positioned in “ON”), it could be an indication of leaking of brake fluid or worn brake pads. immediately stop the vehicle at the nearest safe place and check the brake fluid level. If the fluid is below the “MIN” mark in the level reservoir, do not drive the vehicle. Have the vehicle towed to the nearest SUBARU dealer for repair. ! Electronic Brake Force Distribution


(EBD) system warning


The brake system warning light also


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


illuminates if a malfunction occurs in the EBD system. In that event, it comes on together with the ABS warning light. The EBD system may be malfunctioning if the brake system warning light and ABS warning light illuminate simultaneously during driving. Even if the EBD system fails, the conven- tional braking system will still function. However, the rear wheels will be more prone to locking when the brakes are applied harder than usual and the vehi- cle’s motion may therefore become some- what harder to control. If the brake system warning light and ABS warning light illuminate simultaneously, take the following steps: 1. Stop the vehicle in the nearest safe, flat place. 2. Shut down the engine, apply the parking brake and then restart it. If both 3. Release the parking brake. warning lights go out, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights come on again and stay illuminated after the engine has been restarted, shut down the engine again, apply the parking brake, and check the brake fluid level.


If the brake fluid level is not below the 5. “MIN” mark, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspected. 6. is below the “MIN” mark, DO NOT drive the vehicle. Instead, have the vehicle towed to the nearest SUBARU dealer for repair. & Door open warning


the brake fluid level


If


light


The door open warning light comes on if any door or the rear gate is not fully closed.


Always make sure this light is out before you start to drive. & All-Wheel Drive warn-


ing light (AWD AT vehicles – if equipped)


The All-Wheel Drive warning light comes on when the ignition switch is turned to the “ON” position and goes out after the engine has started. This light comes on when All-Wheel Drive is disengaged and the drive mechanism is switched to Front Wheel Drive for main- tenance or similar purposes (Non-turbo vehicles).


Black plate (129,1)


Instruments and controls 3-19


It flashes if the vehicle is driven with tires of differing diameters fitted on the wheels or with an excessively low air pressure in any of the tires.


CAUTION


Continuing to drive with the AWD warning light flashing can damage the powertrain. If the AWD warning light starts to flash, promptly park in a safe place and check whether the tires have differing diameters and whether any of the tires has an excessively low inflation pressure.


& Intercooler water spray


warning light (WRX-STI)


This light comes on when the water level in the intercooler water spray tank falls to the lower limit (approximately 0.4 US qt, 0.4 liter, 0.4 Imp qt).


– CONTINUED –


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


3-20 Instruments and controls


& Selector lever position indi-


cator (AT vehicles)


& High beam indicator


light


This light shows that the headlights are in the high beam mode. This indicator light also comes on when the headlight flasher is operated. & Cruise control indica-


tor light


The cruise control indicator light comes on when the ignition switch is turned to the “ON” position and goes out after approxi- mately 3 seconds. This light comes on when the “CRUISE” main switch is pressed. If you move the cruise control lever or press the main switch button while turning the ignition switch “ON”, the cruise control function is deactivated and the “CRUISE” flashes. To reactivate the indicator light turn the ignition cruise control function, switch back to the “Acc” or “LOCK” position, and then turn it again to the “ON” position. & Cruise control set in-


dicator light


The cruise control set light comes on when the ignition switch is turned to the “ON” position and goes out


indicator


This indicator shows the position of the selector lever. & Turn signal indicator


lights


These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to the “Replacing bulbs” section in chapter 11.


Black plate (130,1)


after approximately 3 seconds. This light comes on when vehicle speed has been set. & Driver’s control center differential auto indica- tor light (WRX-STI)


This light functions while the ignition switch is “ON”. When on, it indicates that the driver’s control center differential is set to AUTO mode. It goes off when the driver’s control center differential’s manual mode switch is pressed. For details, refer “Driver’s Control Center to Chapter 7, Differential (DCCD) (WRX-STI)”.


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


& Driver’s control center differ- ential indicator and warning lights (WRX-STI)


! Indicator lights


! Warning light


Black plate (131,1)


Instruments and controls 3-21


& REV indicator light


(WRX-STI)


This light comes on when the engine speed reaches a level set by driver and when the tachometer needle enters the red zone.


When illuminated, one of these indicator lights indicates the initial limited slip differential (LSD) torque currently selected for the center differential.


failure of


The bottom indicator light “ ” flashes in the the driver’s control event of center differential. Have the vehicle in- spected by your SUBARU dealer. For details, refer to Chapter 7, “Driver’s Con- trol Center Differential (WRX- STI)”. & Lights indicator light


(DCCD)


(WRX-STI)


This light comes on when the headlight switch is placed in the “ ” position.


” or



北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


Black plate (132,1)


3-22 Instruments and controls


Clock


Light control switch


& Headlights


The light switch operates only when the ignition switch is in the “ON” position.


WARNING


To prevent battery discharge result- ing from accidentally leaving your lights on when your vehicle is parked, the light switch operates only when the ignition switch is in the “ON” position. In any other position, the vehicle’s lights will be out. If you park your vehicle on a road- side at night, use the hazard warn- ing flasher to alert the other drivers.


To turn on the headlights, turn the knob on the end of the turn signal lever.


first position


Parking lights, instrument panel illumina- tion, tail lights, front side marker lights and license plate light are on.


second position


illumination,


Headlights, parking lights, instrument pa- nel front side marker lights, and license plate light are on.


lights,


tail


To set the hour, press the “H” button. To set the minutes, press the “M” button. To reset the minutes to “00” with a radio time signal, push the “SET” button.


CAUTION


To ensure safety, do not attempt to set the time during driving, as an accident from inadequate attention to the road could result.


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


Black plate (133,1)


& Headlight flasher


& Daytime running light system


Instruments and controls 3-23


& High/low beam change (dim-


mer)


To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indicator light “ ” on the instru- ment panel is also on. To switch back to low beam, pull the lever back to the detent position.


To flash the headlights, pull the lever toward you and then release it. The high beam will stay on for as long as you hold the lever. The headlight flasher works even though the light switch is in the “OFF” position.


When the headlights are on high beam, the high beam indicator light “ ” on the instrument panel also comes on.


CAUTION


Do not hold the lever in the flashing position for more than just a few seconds.


! WRX-STI The low beam headlights, side marker lights, tail lights, parking lights, and license plate lights will automatically come on when the engine has started, under the following conditions: . The parking brake is fully released. . The light switch is in the “OFF” or “ position. . The automatic transmission selector lever is set at other than the “P” position.



WARNING


The light switch must always be turned to the “ ” position when it is dark outside.


! Except WRX-STI The low beam headlights will automati- cally come on at reduced brightness when the engine has started, under the following conditions: . The parking brake is fully released. . The light switch is in the “OFF” or “ position. . The automatic transmission selector lever is set at other than the “P” position.



– CONTINUED –


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


Black plate (134,1)


3-24 Instruments and controls


WARNING


Turn signal lever


return automatically to the neutral position when you release it.


The tail lights, parking lights, and side marker lights are not turned on by the daytime running light system. The light switch must always be turned to the “ ” position when it is dark outside.


1) Right turn 2) 3) 4)


Left turn Lane change for right Lane change for left


To activate the right turn signal, push the lever up. To activate the left turn signal turn signal, push the turn signal lever down. When the turn is finished, the lever will return automatically. If the lever does not return after cornering, return the lever to the neutral position by hand.


To signal a lane change, push the turn signal lever up or down slightly and hold it during the lane change. The turn signal indicator lights will flash in the direction of the turn or lane change. The lever will


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


Black plate (135,1)


Instruments and controls 3-25


Illumination brightness con- trol


Headlight beam leveler (U.S.- spec. WRX-STI)


Parking light switch


” When the headlight switch is in the “ or “ ” position, you can adjust bright- ness of the instrument panel illumination for better visibility.


To brighten, turn the control dial upward. To darken, turn the control dial downward.


The WRX-STI version has High-Intensity Discharge (HID) headlights on the low beam setting. The HID headlights gener- ate more light than conventional halogen headlights. Therefore a driver of an oncoming vehicle may experience too much glare when your headlight beam height adjustment is high due to the vehicle carrying heavy load. The headlight beam leveler can be used to adjust beam height to avoid such a condition.


The higher the number the knob is turned to, the lower the beam becomes.


The parking light switch operates regard- less of the ignition switch position.


By pushing the front end of this switch, following lights will come on. – Parking lights – Front side marker lights – Tail lights – License plate lights


To turn off, push the rear end of parking light switch. Avoid leaving these lights on for a long time because that will run down the battery.


the


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


3-26 Instruments and controls


Front fog light button (if equipped)


The front fog lights operate only when the headlights are on low beam. Push the front fog light button to turn the front fog lights on. Press the button again to turn them off. The indicator light located on the button will illuminate when the front fog lights are on.


Black plate (136,1)


Wiper and washer


WARNING


In freezing weather, do not use the windshield washer until the wind- shield is sufficiently warmed by the defroster. Otherwise the washer fluid can freeze on the windshield, blocking your view.


CAUTION


. Do not operate the washer con- tinuously for more than 10 sec- onds, or when the washer fluid tank is empty. This may cause overheating of the washer motor. Check the washer fluid level frequently, such as at fuel stops. . Do not operate the wipers when the windshield or rear window is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield or rear window, always use the wind- shield washer.


. In freezing weather, be sure that the wiper blades are not frozen to the windshield or rear window before switching on the wipers. Attempting to operate the wiper with the blades frozen to the window glass could cause not only the wiper blades to be damaged but also the wiper mo- tor to burn out. the wiper blades are frozen to the window glass, be sure to operate the defroster, windshield wiper dei- cer (if equipped) or rear window defogger before turning on the wiper.


If


. If the wipers stop during opera- tion because of ice or some other obstruction on the window, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the “LOCK” position and clean the window glass to allow proper wiper op- eration.


. Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent.


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


face of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the window glass and wiper blades with clean water. The glass is clean if no beads form on the glass when you rinse with water. . If you cannot eliminate the streaking even after following this procedure, replace the wiper blades with new ones. Refer to the “Replacement of wiper blades” section (chapter 11) for replacement instructions.


(See the “Windshield washer fluid” section in chapter 11.) Also, when driving the vehicle when there are freezing tempera- tures, use non-freezing type wi- per blades.


. Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzene. This will cause deterioration of the wiper blades.


NOTE . The wiper operates only when the ignition switch is in the “ON” or “Acc” position. . Clean your wiper blades and win- dow glass periodically with a washer solution to prevent streaking, and to remove accumulations of road salt or road film. Keep the washer button depressed at least for 1 second so that washer solution will be sprinkled all over the windshield or rear window. . Grease, wax, insects or other mate- rial on the windshield or the wiper blade results in jerky wiper operation and streaking on the glass. If you cannot remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer sur-


Black plate (137,1)


Instruments and controls 3-27


& Windshield wiper and washer


switches


! Windshield wipers


OFF: Park


: Intermittent LO: Low speed HI: High speed


To turn the wipers on, push the wiper control lever down. To turn the wipers off, return the lever to the “OFF” position.


– CONTINUED –


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


3-28 Instruments and controls


! Wiper intermittent time control


! Mist (for a single wipe)


” When the wiper switch is in the “ position, turn the dial to adjust the operat- ing interval of the wiper.


The operating interval can be adjusted in four steps. Two click stop positions of the dial may help you to aim at your desired interval.


For a single wipe of the wipers, pull the lever toward you. The wipers operate until you release the lever. ! Washer


Black plate (138,1)


To wash the windshield, push the washer button at the end of the wiper control lever. The washer fluid sprays until you release the washer button. The wipers operate while you push the button.


& Rear window wiper and washer switch – Wagon


: Washer (accompanied by wiper operation)


ON: Normal OFF: Park : Washer


! Rear wiper The rear wiper offers intermittent opera- tion only. To turn the rear wiper on, turn the knob on the end of the wiper control lever to the “ON” position.


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


To turn the wiper off, return the knob to the “OFF” position. ! Washer To wash the rear window while the rear wiper is operating, turn the knob clockwise to the “ fluid sprays until you release the knob. To wash the rear window when the rear wiper is not in use, turn the knob counter- clockwise to the “ ” position. The washer fluid sprays and the wiper operates until you release the knob.


” position. The washer


Rear window defogger but- ton


The rear window defogger operates only when the ignition switch is in the “ON” position. The rear window defogger button is located on the climate control panel. To turn on the defogger, push the button. To turn it off, push the button again. The indicator light located on the button lights up while the rear window defogger is operating.


If


The defogger will automatically shut off after approximately 15 minutes. the window clears before that time, push the button to turn it off. It also turns off when the ignition switch is turned to the “Acc” or “LOCK” position. If defrosting or defogging is desired when you restart your vehicle, you have to push the button to turn it on again.


Black plate (139,1)


Instruments and controls 3-29


Manual climate control system


Automatic climate control system NOTE . If your vehicle is equipped with the outside mirror defogger, the outside mirror defogger operates while the rear – CONTINUED –


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


3-30 Instruments and controls


window defogger is operating. . Turn on the rear window defogger if the wiper is frozen to the glass.


Windshield wiper deicer (if equipped)


CAUTION


. Do not use sharp instruments or window cleaner containing abra- sives to clean the inner surface of the rear window. They may damage the conductors printed on the window.


. To prevent the battery from being discharged, do not operate the defogger continuously for any longer than necessary.


The windshield wiper deicer operates only when the ignition switch is in the “ON” position.


Before turning on the windshield wiper deicer, remove any snow from the wind- shield. To turn on the windshield wiper deicer, push the button. The indicator light located on the button lights up while the windshield wiper deicer is operating. The windshield wiper deicer will automa- tically shut off after approximately 15
minutes. the windshield wiper blades have been deiced completely before that time, push the button to turn it off. It also turns off when the ignition switch is turned


If


Black plate (140,1)


to the “Acc” or “LOCK” position. If deicing is not complete when you restart your vehicle, you have to push the button to turn the deicer on again. NOTE If your vehicle is equipped with the outside mirror defogger, the outside mirror defogger operates while the windshield wiper deicer is operating.


CAUTION


To prevent the battery from being discharged, do not operate the windshield wiper deicer continu- ously for any longer than necessary.


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


Intercooler water spray switch (WRX-STI)


NOTE


Pressing this switch causes water to be sprayed into the intercooler. It can be used to help maintain adequate intercooler performance when the outside tempera- ture is high.


Water is sprayed for approximately 2
seconds every time the switch is pressed and then released.


. The intercooler water spray warning light comes on when the water level in the tank has dropped to the lower limit. If the warning light illuminates, refill the tank with water. The tank is located on the right-hand side of the trunk. For the tank refilling method, refer to the “Intercooler water spray (WRX-STI)” section in chapter 11. . In cold weather (when you do not use the intercooler water spray), keep the tank half-empty or below in case the water freezes. A larger amount of water could break the tank if it froze.


Black plate (141,1)


Instruments and controls 3-31


CAUTION


Do not press the switch when the warning light is illuminated. If the switch is kept pressed when the tank is short of water, the water pump motor could overheat.


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


Black plate (142,1)


3-32 Instruments and controls


Mirrors


Always check that the inside and outside mirrors are properly adjusted before you start driving.


& Inside mirror


! Auto-dimming mirror/compass (if


equipped)


illuminated compass reading will appear in the lower part of the mirror.


Even with the mirror in anti-glare mode, the mirror surface turns bright the transmission is shifted into reverse. This is to ensure good rearward visibility during reversing. ! Photosensors


if


The inside mirror has a day and night position. Pull the tab at the bottom of the mirror toward you for the night position. Push it away for the day position. The night position reduces glare from head- lights.


Left button


1) 2) Auto dimming indicator 3) Photosensor 4) Right button


The auto-dimming mirror has an anti-glare feature which automatically reduces glare coming from headlights of vehicles behind you. It also contains a built-in compass. . By pressing and releasing the left button, the automatic dimming function is toggled on or off. When the automatic dimming function is on, the auto dimming indicator light (green) located to the right of the button will illuminate. . By pressing and releasing the right button, the compass display is toggled on or off. When the compass is on, an


The mirror has a photosensor attached on both the front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors detect it and make the reflection surface of the mirror dimmer to help prevent you from being blinded. For this reason, use care not to cover the sensors with stickers, or other similar items. Periodically wipe the sensors clean using a piece of dry soft


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


cotton cloth or an applicator. ! Compass calibration 1. For optimum calibration, switch off all nonessential electrical accessories (rear window defogger, heater/air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive to an open, level area away from large metallic objects or structures and make certain the ignition switch is in the “ON” position. 3. Press and hold the left button for 3
seconds then release, and the compass will enter the calibration mode. “CAL” and direction will be displayed. 4. Drive slowly in a circle until “CAL” disappears from the display (approxi- mately two or three circles). The compass is now calibrated. 5. Further calibration may be necessary should outside. Influences cause the mirror to read inaccurately. You will know that this has occurred if your compass begins to read in only limited directions. Should you encounter this situation, return to step one of the above procedure and recalibrate the mirror.


Black plate (143,1)


Instruments and controls 3-33


! Compass zone adjustment


exit the zone setting mode.


& Outside mirrors


Compass calibration zones


1. The zone setting is factory preset to Zone 8. Refer to the “Compass calibration zone” map shown above or one attached to the end of this manual to verify that the compass zone setting is correct for your geographical location. 2. Press and hold the right button for 3
seconds then release, and the word “ZONE” will briefly appear and then the zone number will be displayed. 3. Press the right-hand button repeatedly to cycle the display through all possible zone settings. Stop cycling when the correct zone setting for your location is displayed. 4. Releasing the button for 3 seconds will


! Convex mirror (Passenger side)


WARNING


Objects look smaller in a convex mirror and farther away than when viewed in a flat mirror. Do not use the convex mirror to judge the distance of vehicles behind you when changing lanes. Use the inside mirror (or glance backwards) to determine the actual size and dis- tance of objects that you view in convex mirror.


– CONTINUED –


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


3-34 Instruments and controls


! Remote control mirror switch


! Outside mirror defogger (if


equipped)


1) Selection switch 2) Direction control switch


The remote control mirrors operate only when the ignition switch is in the “ON” or “Acc” position. 1. Press either end of switch, “L” for the left, “R” for the right. 2. Move the direction control switch in the direction you want to move the mirror. 3. Return the selection switch to the neutral position to prevent unintentional operation.


the selection


The mirrors can also be adjusted manu- ally.


Manual climate control system


Automatic climate control system


The outside mirror defogger shares the button with rear window defogger.


Black plate (144,1)


The outside mirror defogger operates only when the ignition switch is in the “ON” position. To turn on the outside mirror defogger, push the button. To turn it off, push the button again. The indicator light located on the button lights up while the outside mirror defogger is operating.


If


The defogger will automatically shut off after approximately 15 minutes. the mirror clears before that time, push the button to turn it off. It also turns off when the ignition switch is turned to the “Acc” or “LOCK” position. If defrosting or defogging is desired when you restart your vehicle, you have to push the button to turn it on again. NOTE While the outside mirror defogger is operating, the rear window defogger also operates.


CAUTION


To prevent the battery from being discharged, do not operate the de- fogger continuously for any longer than necessary.


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


Black plate (145,1)


Instruments and controls 3-35


Tilt steering wheel


WARNING


Horn


Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and result in personal injury.


1. Adjust the seat position. Refer to the “Front seats” section (chapter 1). 2. Push the tilt lock lever down. 3. Move the steering wheel to the desired level. 4. Pull the lever up to lock the steering wheel in place. 5. Make sure that the steering wheel is securely locked by moving it up and down.


To sound the horn, push the horn pad.


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


Black plate (7,1)


Climate control


Ventilator.............................................................. Air flow selection ................................................ Center and side ventilators..................................


Manual climate control system


(if equipped) ..................................................... Control panel ...................................................... Heater operation ................................................. Air conditioner operation


(if equipped)......................................................


Automatic climate control system


(if equipped) ..................................................... Control panel ...................................................... To use as full-automatic climate control


system..............................................................


To use as semi-automatic climate control


system.............................................................. Fan speed control dial......................................... Temperature control dial...................................... Air flow control dial.............................................


4-2
4-2
4-3


4-3
4-3
4-5


4-7


4-8
4-8


4-8


4-8
4-9
4-9
4-9


Air inlet selection button .................................... Air conditioner button ........................................ Temperature sensors .........................................


Operating tips for heater and air


conditioner ...................................................... Cleaning ventilation grille................................... Efficient cooling after parking in direct


sunlight ...........................................................


Lubrication oil circulation in the refrigerant


circuit.............................................................. Checking air conditioning system before summer season ............................................................ Cooling and dehumidifying in high humidity and low temperature weather conditions ................. Air conditioner compressor shut-off when engine is heavily loaded.............................................. Refrigerant for your climate control system ........ Air filtration system ........................................... Replacing the air filter........................................


4-10
4-10
4-11


4-11
4-11


4-11


4-12


4-12


4-12


4-12
4-12
4-12
4-13


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


Black plate (148,1)


4-2 Climate control


Ventilator & Air flow selection


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


& Center and side ventilators


! Side ventilators


! Center ventilators


1) Open 2) Close


Move the tab up and down or right and left to adjust the flow direction.


Move the knob in any direction you prefer to adjust the flow direction. To open the ventilator, counterclockwise. To close the ventilator, clockwise.


turn the knob


turn the knob


Black plate (149,1)


Climate control 4-3


Manual climate control sys- tem (if equipped) & Control panel


1) Air inlet selection lever 2) Air conditioner button 3) Rear window defogger button (Refer to the “Rear window defogger button” sec- tion in chapter 3.)


4) Air flow control dial 5) 6)


Fan speed control dial Temperature control dial


! Temperature control dial This dial regulates the temperature of air flow from the air outlets over a range from the blue side (cool) to red side (warm).


– CONTINUED –


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


4-4 Climate control


! Fan speed control dial The fan operates only when the ignition switch is turned to the “ON” position. The fan speed control dial is used to select 4
fan speeds. ! Air flow control dial This dial has the following five positions:


: Air flows through the instrument panel


outlets.


: Air flows through the instrument panel


outlets and the foot outlets.


: Air flows through the foot outlets and some through the windshield defroster outlets.


: Air


flows through the windshield


defroster outlets and foot outlets.


: Air


flows through the windshield


defroster outlets. NOTE . You will find the notation “USE WITH ” on the air flow control dial plate. This is intended to remind you to set the air inlet selection lever in the “ ” position when defogging the wind- shield. Defogging with the air inlet selection lever set in the “ ” position provides


” position.


the position of


better defogging performance than in the “ . When the dial is placed in the “ ” or “ ” position, the air conditioner compressor operates automatically re- gardless of the air conditioner button to defog the wind- shield quickly. However the indicator on the air con- ditioner button will not come on. Also, you cannot stop the air condi- tioner compressor by pressing the air conditioner button.


! Air conditioner button (if equipped)


The air conditioner operates only when the engine is running.


Push the air conditioner button while the


Black plate (150,1)


fan is in operation to turn on the air conditioner. The indicator light will come on.


Push it again to turn off the air conditioner. ! Air inlet selection lever


(Recirculation): Interior air is recircu-


lated inside the vehicle. Place the air inlet selection lever in the “ ” position for fast cooling with the air conditioner or when driving on a dusty road.


(Outside air): Outside air is drawn into


the passenger compartment. Place the air inlet selection lever in the “ ” position when the interior has cooled to a comfortable temperature and the road is no longer dusty.


WARNING


Continued operation in the “ ” position may fog up the windows. Switch to the “ ” position as soon as the outside dusty condition clears.


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


& Heater operation


! Defrosting or defogging the wind-


shield


the air conditioner button to


position of defog the windshield quickly. However, the air conditioner indicator light does not come on at this time. NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corre- sponding knob clockwise.


! Heating and defrosting


” position.


To direct warm air to the windshield and front door windows: 1. Set the air inlet selection lever to the “ 2. Set the air flow control dial to the “ position. 3. Turn the temperature control dial all the way to the right. 4. Set the fan speed control dial to the highest speed.



If your vehicle is equipped with an air conditioner, when the “ ” position is selected, the air conditioner compressor automatically operates regardless of the


” or “


To direct warm air toward the floor and the windshield: 1. Set the air inlet selection lever to the “ 2. Set the air flow control dial to the “ position. 3. Set the temperature control dial to the


” position.



Black plate (151,1)


Climate control 4-5


most comfortable level. 4. Set the fan speed control dial to the desired speed.


” or “


If your vehicle is equipped with an air conditioner, when the “ ” position is selected, the air conditioner compressor automatically operates regardless of the position of the air conditioner button to defog the windshield quickly. However, the air conditioner indicator light does not come on at this time. NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corre- sponding knob clockwise.


– CONTINUED –


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


Black plate (152,1)


4-6 Climate control


! Heating


! Bi-level heating


outlets and the air from the foot outlets. ! Ventilation


” position.


To direct warm air toward the floor: 1. Set the air inlet selection lever to the “ 2. Set the air flow control dial to the “ position. 3. Set the temperature control dial to the most comfortable level. 4. Set the fan speed control dial to the desired speed.



NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corre- sponding knob clockwise.


This setting allows you to direct air of different temperatures from the instrument panel and foot outlets. The air from the foot outlets is slightly warmer than from the instrument panel outlets. 1. Set the air inlet selection lever to the “ 2. Set the air flow control dial to the “ position. 3. Set the temperature control dial to the desired temperature level. 4. Set the fan speed control dial to the desired speed.


” position.



Setting the temperature control dial fully turned to the red area or blue area decreases the temperature difference between the air from the instrument panel


” position.


To force outside air through the instrument panel outlets: 1. Set the air inlet selection lever to the “ 2. Set the air flow control dial to the “ position. 3. Set the temperature control dial all the way left. 4. Set the fan speed control dial to the desired speed.



When driving on a dusty road, set the air inlet selection lever to the “ ” position.


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


Black plate (153,1)


Climate control 4-7


4. Set the fan speed control dial at the highest speed.


in the “


The air conditioner compressor automati- cally operates when the air flow control ” position to dial set provide better defogging performance. However, the air conditioner indicator light does not come on at this time.


” or “


WARNING


Continued operation in the “ ” position may fog up the windows. Switch to the “ ” position as soon as the outside dusty condition clears.


& Air conditioner operation (if


equipped)


! Cooling or dehumidifying



2. Set the air flow control dial to the “ position. 3. Set the air conditioner button to the “ON” position. 4. Set the temperature control dial to the blue side. 5. Set the fan speed control dial at the desired speed.


! Defrosting or defogging


For cooling and dehumidification of the passenger compartment, performing the following steps will allow air to flow through the instrument panel outlets: 1. Set the air inlet selection lever to the “


” position.


” position.


To direct warm air to the windshield and front door windows: 1. Set the air inlet selection lever to the “ 2. Set “ 3. Set the temperature control dial to the red side.


the air outlet control dial to the


” position.


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


4-8 Climate control


Automatic climate control system (if equipped)


Although this climate control system can be used as a full-automatic climate control system, it can also, if desired, be used as a semi-automatic climate control system. When it is used as a full-automatic climate control system, the outlet air temperature, fan speed, air flow distribution, air inlet control, and air conditioner compressor operation are all automatically controlled to maintain a constant, comfortable tem- perature inside the vehicle. NOTE . Operate the automatic climate con- trol system when the engine is running. . When the engine coolant is cold, the blower does not run. . In the “AUTO” mode, when the air temperature in the passenger compart- ment is sufficiently cool, the air condi- tioner compressor does not operate. For efficient defogging or dehumidify- ing in cold weather, press the “A/C” button to operate the air conditioner compressor. . Even when cooling is not necessary, setting the temperature much lower than the current outlet air temperature turns on the air conditioner compres-


sor automatically and the “A/C” indi- cator light on the control panel comes on.


& Control panel


Fan speed control dial Temperature control dial


1) Air flow control dial 2) 3) 4) Air conditioner button 5) Air inlet selection button 6) Rear window defogger button (Refer to the “Rear window defogger button” sec- tion in chapter 3.)


& To use as full-automatic cli-


mate control system


Place the temperature control dial in the position for your desired temperature, then set the other dials and buttons as de-


Black plate (154,1)


scribed in the following. The system’s functions will then switch to AUTO mode and be controlled automatically. . Air flow control dial: AUTO position . Fan speed control dial: AUTO position . Air inlet selection button: Press for at least 1 second. (Indicator will flash twice.) . Air conditioner button: Press for at least 1 second. (Indicator will flash twice.)


& To use as semi-automatic


climate control system


Each function can be individually set to AUTO mode independently of the others. Any function set to AUTO mode is con- trolled automatically. Any function not set to AUTO mode can be manually adjusted as desired. The temperature can be set within a range of 65 to 858F (20 to 308C).


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


& Fan speed control dial


NOTE With the fan speed control dial in the AUTO position and the air flow control dial in the “ ”, or “ ” position, the fan does not operate during engine warm-up until the engine coolant tem- perature exceeds approx. 1228F (508C).


”, “


& Temperature control dial


The fan operates only with the ignition switch in the ON position. The fan speed control dial is used to select the AUTO (automatic control) mode or to select the desired fan speed. The dial’s positions and their functions are as follows: OFF: The fan does not operate. AUTO: The fan speed is adjusted auto- matically in accordance with the air temperature inside and outside the pas- senger compartment, the intensity of sun- light, and other factors. SUBARU recom- mends using the AUTO position. Other positions: The fan speed can be adjusted in 25 steps.


This dial is used to set the desired interior temperature. With the dial set to your desired temperature, the system automa- tically adjusts the temperature of air supplied from the outlets such that the desired temperature is achieved and maintained. If the dial is turned fully counterclockwise, the system gives maximum cooling per-


Black plate (155,1)


Climate control 4-9


formance. If the dial is turned fully clock- wise, the system gives maximum heating performance.


& Air flow control dial


This dial has the following six positions. The outlets from which air is supplied in each position are as follows: AUTO: The air flow control is adjusted automatically in accordance with the air temperature inside and outside the pas- senger compartment, the intensity of sun- light, and other factors. SUBARU recom- mends using the AUTO position.


: Instrument panel outlets


Instrument panel outlets and foot


outlets


: Foot outlets and windshield defroster – CONTINUED –


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


4-10 Climate control


outlets (relatively little air from windshield defroster outlets)


: Windshield defroster outlets and foot


outlets


: Windshield defroster outlets


NOTE When the dial is placed in the “ ” or “ ” position, the air conditioner com- pressor operates automatically to de- fog the windshield quickly. At the same time, the air inlet selection is automa- tically set to “outside air” mode.


& Air inlet selection button


ON position (Recirculation): Interior air is recirculated inside the vehicle. Push the air inlet selection button to the ON position


for fast cooling with the air conditioner or when driving on a dusty road. The indicator light will come on. OFF position (Outside Air): Outside air is drawn into the passenger compartment. Push the air inlet selection button to the OFF position when the interior has cooled to a comfortable temperature and the road is no longer dusty. The indicator light will go off. AUTO: When the air inlet selection button is pressed for at least one second, the indicator flashes twice. The air inlet control is then adjusted automatically in accor- dance with the air temperature inside and outside the passenger compartment, the intensity of sunlight, and other factors. Pressing the air inlet selection button cancels the “AUTO” mode. SUBARU recommends using the AUTO position.


WARNING


Continued operation in the ON posi- tion may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears.


Black plate (156,1)


& Air conditioner button


The button’s positions and their functions are as follows: ON: The air conditioner operates while the fan is running. Push the button to select this position. The indicator light will illuminate. OFF: The air conditioner does not oper- ate. Push the button again to select position. The indicator light will go off. AUTO: When the button is pressed for at least one second, the indicator flashes twice. The air conditioner compressor operation is then adjusted automatically in accordance with the air temperature inside and outside the passenger com- partment, the intensity of sunlight, and


this


北米Model "A1920BE-B" EDITED: 2006/ 9/ 19


Black plate (157,1)


Climate control 4-11


other factors. Pressing the button cancels the “AUTO” mode. SUBARU recommends using the AUTO position. NOTE The air conditioner’s compressor does not operate with an outside tempera- ture of 328F (08C) or lower.


& Temperature sensors


cautions: – Do not subject the sensors to impact. – Keep water away from the sensors. – Do not cover the sensors.


Operating tips for heater and air conditioner & Cleaning ventilation grille


The sensors are located as follows: – Solar sensor: beside windshield defros- ter grille – Interior air temperature sensor: beside the fan speed control dial – Outside temperature sensor: behind front grille.


Interior air temperature sensor


1) 2) Solar sensor


The automatic climate control system employs several sensors. These sensors are delicate. treated properly and become damaged, the sys- tem may not be able to control the interior temperature correctly. To avoid damaging the sensors, observe the following pre-


they are not


If


Always keep the front ventilator inlet grille free of snow, leaves, or other obstructions

Loading...
x