to damage the printed circuit board in the trans- mitter when replacing the battery. . Be careful not to allow children to touch the battery and any re- moved parts; children could swallow them.
. There is a danger of explosion if an incorrect replacement battery is used. Replace only with the same or equivalent type of bat- tery.
. Batteries should not be exposed to excessive heat such as sun- shine, fire or the like.
When the transmitter battery begins to get weak, range will begin to decrease. Replace the battery as soon as possible.
transmitter
1. Open the transmitter case using a flat- head screwdriver.
2. Remove the old battery from the holder.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
2-12 Keys and doors
1) Negative (−) side facing up
3. Replace with a new battery (type CR2025 or equivalent) making sure to install the new battery with the negative (−) side facing up. 4. Refit the removed half of the transmit- ter case.
After the battery is replaced, the trans- mitter must be synchronized with the remote keyless entry system’s control unit. Press either the “ ” or “ ” button six times to synchronize the unit. & Replacing lost transmitters to If you lose a transmitter or want transmitters (up to purchase additional four can be programmed), you should re- program all of your transmitters for secur-
ity reasons. It is recommended that you have your dealer program all of your transmitters into your system. ! Programming the transmitters The remote keyless entry system is equipped with a special code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmitter codes. The four transmitter codes may be the same or different. Programming transmitter codes into system:
Bag containing transmitter
Black plate (102,1)
Transmitter circuit board
To register a new transmitter with the
remote keyless entry system, it is neces-
sary to program the transmitter’s code
(identification number) into the system. A
label showing the code is affixed to the
bag containing the transmitter, and an-
other is affixed to the circuit board inside
the transmitter. If there is no bag, open the
transmitter case and make a note of the
eight-digit number. Program the number
into the system in accordance with the
following procedure:
1. Firmly close the doors and the rear
gate, or trunk lid.
2. Open the driver’s door, sit
driver’s seat, and close the door.
3. Perform the following steps within 45
seconds.
in the
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (103,1)
Keys and doors 2-13
position to the “ON” position 10 times within 15 seconds.
NOTE . When you complete step (2), an electronic tone will sound once. . If you do not perform steps (1) and (2) within 45 seconds, an error will occur. Neither an electronic tone nor the buzzer will sound, and the interior lamp will not flash. In this event, per- form the whole procedure again begin- ning with part 1. 4. Open and close the door once within 15 seconds. NOTE . When part 4 of the procedure is completed, an electronic tone will sound for 30 seconds. . If you do not perform the operations in part 4 within 15 seconds, an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with part 3 of the procedure.
Type A
Type B
5. Before the electronic tone stops sounding, push the lock side of the power door lock switch the same number of times as the leftmost digit of the transmit-
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
(1) Open and close the driver’s door once.
1) ON 2)
LOCK
(2) Insert the key into the ignition switch, then turn it from the “LOCK”
2-14 Keys and doors
ter code. For example, push the lock
switch eight times if the leftmost digit of
the code is 8.
NOTE
. The electronic tone will stop sound-
ing when you start entering the num-
ber.
. If you do not start entering the
number using the lock switch before
the electronic tone stops sounding, an
error will occur. In this event, perform
the registration steps again beginning
with part 3 of the procedure.
. If the interval between one push of
the switch and the next exceeds 5
seconds, an error will occur.
In this
event, perform the procedure again
beginning with part 4. If an error occurs
six times, perform the procedure again
starting with part 3.
Type A
Type B
6. When you have finished entering the number, push the unlock side of the lock switch within 5 seconds.
Black plate (104,1)
the remaining digits of
NOTE
. An electronic tone will sound.
. If you push the unlock side of the
lock switch when more than 5 seconds
have passed, an error will occur. In this
event, perform the procedure again
beginning with part 4. If an error occurs
six times, perform the procedure again
starting with part 3.
7. Perform parts 5 and 6 of the procedure
for each of
the
transmitter code beginning with the sec-
ond digit
(counting from the left) and
finishing with the eighth digit.
NOTE
. When you finish entering the eighth
digit, an electronic tone will sound for
30 seconds.
. If the interval between one push of
the switch and the next exceeds 5
seconds, an error will occur.
In this
event, perform the procedure again
beginning with part 4. If an error occurs
six times, perform the procedure again
starting with part 3.
8. Before the electronic tone stops
sounding, use the power door lock switch
to reenter the transmitter code beginning
with the leftmost digit.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
NOTE If you do not start entering the number using the lock switch before the elec- tronic tone stops sounding, an error will occur. In this event, perform the procedure again beginning with part 3. 9. When you have finished entering the code a second time, an electronic tone will sound for 1 second and automatic door locking and unlocking operation will take place once to indicate completion of registration, provided the code entered the second time is identical to that entered the first time. NOTE If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3. 10. If you wish to program another trans- mitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure begin- ning with part 4. When you have finished programming all of the necessary trans- mitter codes into the system, remove the key from the ignition switch.
11. Test every registered transmitter confirm correct operation.
to
lost
! Deleting old transmitter codes The control unit of the remote keyless entry system has four memory locations to store transmitter codes, giving it the ability to operate with up to four transmitters. When you lose a transmitter, the lost transmitter’s code remains in the memory. For security reasons, transmitter codes should be deleted from the mem- ory. To delete old transmitter codes, program four transmitter codes into the system. If you have only one current transmitter, program it If you have two current transmitters, program each one twice. If you have three current transmit- ters, program two of them once and the third one twice. This process will leave only current transmitter codes in the system’s memory. NOTE Make sure no one else is operating their keyless entry system within range of your vehicle when programming transmitters. If someone else were to operate their remote transmitter while you are programming your transmit- ters, it is possible that their transmitter
four times.
Black plate (105,1)
Keys and doors 2-15
code will be programmed into your system, allowing them unauthorized access to your vehicle.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
2-16 Keys and doors
Alarm system
The alarm system helps to protect your vehicle and valuables from theft. The horn sounds and the turn signal lights flash if someone attempts to break into your vehicle. The starter motor is also inter- rupted to prevent starting the vehicle without a key.
The system can be armed and disarmed with the remote transmitter. The system does not operate when the key is inserted into the ignition switch. Your vehicle’s alarm system has been set for activation at the time of shipment from the factory. You can set the system for deactivation yourself or have it done by your SUBARU dealer.
& System operation
The alarm system will sound the following
alarms when triggered.
. The vehicle’s horn will sound for 30
seconds.
. The turn signal
seconds.
lights will flash for 30
If any of the doors or the rear gate/trunk lid remains open after the 30-second period, the horn will continue to sound for a maximum of 3 minutes. If the door or the
rear gate/trunk lid is closed while the horn is sounding, the horn will stop sounding with a delay of up to 30 seconds.
The alarm is triggered by: . Opening any of the doors, the rear gate or trunk lid . Physical impact to the vehicle, such as forced entry (only models with shock sensors (dealer option)) NOTE The alarm system can be set to trigger the illumination of the following interior lights. . Dome light (illuminates only when the dome light switch is in the “DOOR” position) . Map lights (models with moonroof)
The notifications regarding the dome light and the map lights are deactivated as the factory setting. A SUBARU dealer can activate the system. Contact your SUBARU dealer for details.
& Activating and deactivating
the alarm system
To change the setting of your vehicle’s alarm system for activation or deactiva- tion, do the following. 1. Disarm the alarm system. Refer
to
Black plate (106,1)
“Disarming the system” F2-19. in the driver’s seat and shut all 2. Sit doors (and the rear gate if your vehicle is a 5-door). 3. Turn the ignition switch to the “ON” position. 4. Hold down the REAR (UNLOCK) side of the driver’s power door locking switch, open the driver’s door within the following 1 second, and wait 10 seconds without releasing the switch. The setting will then be changed as follows.
If the system was previously activated: The odometer/trip meter screen displays “AL oF” and the horn sounds twice, indicating that the system is now deacti- vated. If the system was previously deacti- vated: The odometer/trip meter screen displays “AL on” and the horn sounds once, indicating that the system is now acti- vated. NOTE You may have the above setting change done by your SUBARU dealer.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
& If you have accidentally trig-
gered the alarm system
! To stop the alarm Do any of the following operations: . Press any button on the remote trans- mitter. . Turn the ignition switch to the “ON” position. NOTE Only registered keys will stop the alarm. If the immobilizer transponder is not registered, the alarm will not stop.
& Arming the system ! To arm the system using remote
transmitter
1. Close all windows. 2. Remove the key from the ignition switch. 3. Open the doors and get out of vehicle. 4. Make sure that the engine hood (and the trunk lid on the 4-door) are locked. 5. Close all doors (and the rear gate on the 5-door).
the
Black plate (107,1)
Keys and doors 2-17
: Press to Arm the system.
: Press to Disarm the system.
Turbo models
Non-turbo models
6. Briefly press the “ ” button (for less than 2 seconds). All doors (and the rear gate on the 5-door) will lock, an electronic chirp will sound once, the turn signal lights will flash once, and the security indicator light will start flashing rapidly. After rapid flashing for 30 seconds (standby time), the indicator lights will then flash slowly (twice approximately every 2 seconds), indicat- ing that the system has been armed for surveillance.
If any of the doors, (rear gate or trunk lid) fully closed, an electronic chirp is not sounds five times, the turn signal lights flash five times to alert you that the doors (or the rear gate) are not properly closed. When you close the door, the system will automatically arm and doors will automa- – CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
2-18 Keys and doors
tically lock. ! To arm the system using power
door locking switches
1. Close all windows. 2. Remove the key from the ignition switch. 3. Open the doors and get out of vehicle. 4. Make sure that locked. 5. Close the doors (and the rear gate on the 5-door) but leave only the driver’s door or the front passenger’s door open.
the engine hood is
the
Type A
Black plate (108,1)
are fully closed before arming the system. . The 30-second standby time can be eliminated if you prefer. Have it per- formed by your SUBARU dealer. . If your vehicle is a 4-door and you unlock the trunk using the remote transmitter’s “ ” button with the alarm system armed, the system will be temporarily placed in a standby state. The system will go back to the surveillance state upon locking the trunk. . The system is in the standby mode for a 30-second period after locking the doors with the remote transmitter. The security indicator light will flash at short intervals during this period. . If any of the following actions are done during the standby period, the system will not switch to the surveil- lance state.
– Doors are unlocked using the remote transmitter. – Any door (including the rear gate of a 5-door or the trunk of a 4-door) is opened. – Ignition switch is turned to the “ON” position.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Type B
6. Push the front side (“LOCK” side) of the power door locking switch to set the door locks. 7. Close the door. An electronic chirp will sound once, the turn signal lights will flash once and the security indicator light will start flashing rapidly. After rapid flashing for 30 seconds (standby time), the indi- cator lights will then flash slowly (twice approximately every 2 seconds), indicat- ing that the system has been armed for surveillance.
NOTE . The system can be armed even if the engine hood and/or the windows are opened. Always make sure that they
& Disarming the system
Briefly press the “
” button (for less than
2 seconds) on the remote transmitter. The
driver’s door will unlock, an electronic
chirp will sound twice,
the turn signal
lights will flash twice. The flashing of the
security indicator light will
then change
slowly (once approximately every 3 sec-
onds from twice approximately every 2
seconds), indicating that the alarm system
has been disarmed.
NOTE
After disarming the alarm system,
briefly press the “
” button a second
time within 5 seconds to unlock all
other doors and the rear gate (5-door).
! Emergency disarming
If you cannot disarm the system using the
transmitter
is lost,
broken or the transmitter battery is too
weak), you can disarm the system without
using the transmitter as follows.
. Turn the ignition switch from the
“LOCK”
to the “ON” position with a
registered key.
the transmitter
(i.e.
& Valet mode When you choose the valet mode, the alarm system does not operate. In valet mode, the remote transmitter is used only
for locking and unlocking the doors and rear gate (5-door) and panic activation.
To enter the valet mode, change the setting of your vehicle’s alarm system for deactivation mode. Refer to “Activating and deactivating the alarm system” F2- 16. The security indicator light will con- tinue to flash once every 3 seconds indicating that the system is in the valet mode.
To exit valet mode, change the setting of your vehicle’s alarm system for activation mode. Refer to “Activating and deactivat- ing the alarm system” F2-16.
& Passive arming When passive arming mode has been programmed by the dealer, arming of the system is automatically accomplished without using the remote transmitter. Note that in this mode, DOORS MUST BE MANUALLY LOCKED. ! To enter the passive mode If you wish to program the passive arming mode, have it done by your SUBARU dealer.
Black plate (109,1)
Keys and doors 2-19
! Arming the system
CAUTION
In passive mode, the system will automatically activate the alarm but WILL NOT automatically lock the doors. In order to lock the doors you must either lock them as in- dicated in step 4 below or with the key once they have been closed. Failure to lock the doors manually will result in a higher security risk.
1. Turn the ignition switch to the “ON” position.
1) ON 2)
LOCK
2. Turn the ignition switch from “ON” to – CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (110,1)
2-20 Keys and doors
“LOCK” position and remove the key from the ignition switch. 3. Open the doors and get out of vehicle.
the
4. Before closing the doors, lock all doors with the inside door lock levers. 5. Close the doors. The system will automatically arm after 1 minute.
In the passive mode, the system can also be armed with the remote transmitter or with the power door locking switches. If the remote transmitter or power door locking switch is used to lock the vehicle, arming will take place immediately regard- less of whether or not the passive mode has been selected.
” button on the transmitter.
! Disarming the system To disarm the system, briefly press the “ & Tripped sensor identification The security indicator light flashes when the alarm system has been triggered. Also, the number of flashes indicates the location of unauthorized intrusion or the severity of impact on the vehicle.
When the ignition switch is turned to the “ON” position, the indicator light will light for 1 second and then flash as follows. . When a door or rear gate (5-door) was opened: 5 times . When a door or the trunk (4-door) was opened: 4 times . When the ignition switch was turned to the “ON” position: 3 times . When a strong impact or multiple impacts were sensed: twice (only models with shock sensors (dealer option)) . When a light impact was sensed: once (only models with shock sensors (dealer option)) NOTE Any of the above indicator light flash- ings will recur each time the ignition switch is turned to the “ON” position. Rearming the alarm system cancels the
flashing.
& Shock sensors (dealer op-
tion)
The shock sensors trigger
the alarm
system when they sense impacts applied
to the vehicle and when any of
their
electric wires are cut. The alarm system
causes the horn to sound and the turn
signal lights to flash for a short time when
the sensed impact is weak, but it warns of
a strong impact or multiple impacts by
sounding the horn and flashing the turn
signal lights, both lasting approximately 30
seconds.
If you desire, your SUBARU dealer can
connect them and set them for activation
or deactivation.
NOTE
. The shock sensors are not always
able to sense impacts caused by break-
ing in, and cannot sense an impact that
does not cause vibration (such as
breaking the glass using a rescue
hammer).
. The shock sensors may sense vi-
bration as indicated in the following
examples and trigger the alarm system.
Select the settings of the alarm system
and shock sensors appropriately de-
pending on where you usually park
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
your vehicle. Examples:
– Vibration from a construction site – Vibration in a multistory car park – Vibration from trains
. You can have the sensitivity of the shock sensors adjusted to your pre- ference by your SUBARU dealer.
Child safety locks
Each rear door has a child safety lock that prevents the door from being opened even if the inside door handle is pulled. When the child safety lock lever is in the lock position, the door cannot be opened from inside regardless of the position of the inner door handle lock lever. The door can only be opened from the outside.
WARNING
Always turn the child safety locks to the “LOCK” position when children sit in the rear seat. Serious injury could result if a child accidentally opens the door and falls out.
Black plate (111,1)
Keys and doors 2-21
Windows & Power windows
WARNING
To avoid serious personal injury caused by entrapment, always con- form to the following instructions without exception. . When operating the power win- dows, be extremely careful to prevent anyone’s fingers, arms, neck, head or other objects from being caught in the window.
. Always lock the passengers’ win- dows using the lock switch when children are riding in the vehicle. . Before leaving the vehicle, al- ways remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operat- ing the power window.
The power windows operate only when the ignition switch is in the “ON” position.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
2-22 Keys and doors
! Driver’s side switches
! Operating the driver’s window
(type A)
1) 2)
3) 4) 5)
Lock switch For driver’s window (with one-touch auto up and down feature (type A)/one-touch auto down feature (type B)) For front passenger’s window For rear left window For rear right window
All door windows can be controlled by the power window switch cluster at the driver side door.
1) Automatically open/close 2) Open/close
To open: Push the switch down lightly and hold it. The window will open as long as the switch is held. This switch also has a one-touch auto down feature that allows the window to be opened fully without holding the switch. Push the switch down until it clicks and release it, and the window will fully open. To stop the window halfway, pull the switch up lightly.
To close: Pull the switch up lightly and hold it. The window will close as long as the switch is
Black plate (112,1)
held. This switch also has a one-touch auto up feature that allows the window to be closed fully without holding the switch. Pull the switch up until it clicks and release it, and the window will fully close. To stop the window halfway, push the switch down lightly. NOTE If the vehicle’s battery is disconnected due to situations such as battery or fuse replacement, the one-touch auto up/down function is deactivated. Initi- alize the power window to reactivate the one-touch auto up/down function. Refer to “Initialization of power window (type A)” F2-24.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
! Operating the driver’s window
(type B)
1) Open 2) Automatically open 3) Close
To open: Push the switch down lightly and hold it. The window will open as long as the switch is held. This switch also has a one-touch auto down feature that allows the window to be opened fully without holding the switch. Push the switch down until it clicks and release it, and the window will fully open. To stop the window halfway, pull the switch up lightly.
To close: Pull the switch up lightly and hold it. The window will close as long as the switch is held. ! Anti-entrapment function (type A)
CAUTION
. Never attempt to test this func- tion using fingers, hands or other parts of your body.
. The anti-entrapment
function may not operate properly if some object gets trapped just before the window fully closes.
NOTE . If a window detects an impact simi- lar to that caused by trapping an object (for example, when the vehicle encoun- ters a deep pothole), the anti-entrap- ment function may operate. . The window cannot be operated for a few seconds after the anti-entrap- ment function operates. . If the vehicle’s battery is discon- nected due to situations such as battery or fuse replacement, the anti- entrapment function is deactivated. Initialize the power window to reacti- vate the anti-entrapment function. Re-
Black plate (113,1)
Keys and doors 2-23
if
fer to “Initialization of power window (type A)” F2-24. While closing the driver’s window auto- the window senses a sub- matically, stantial enough object trapped between the window and the window frame, it automatically moves down slightly and stops. ! Operating the passengers’ windows
To open: Push the appropriate switch down and hold it until the window reaches the desired position. To close: Pull the switch up and hold it until window reaches the desired position.
the
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
2-24 Keys and doors
! Locking the passengers’ windows
! Passengers’ side switches
Lock
1) 2) Unlock
1) Open 2) Close
Push the lock switch. When the lock switch is in the “LOCK” position, the passengers’ windows cannot be opened or closed. Push the switch again to cancel passengers’ window locking.
the
To open: Push the switch down and hold it until the window reaches the desired position. To close: Pull the switch up and hold it until window reaches the desired position.
the
When the lock switch on the power window switch cluster, located on the driver’s side door, is in the “LOCK” position, the passengers’ windows cannot be operated with the passengers’ switches.
Black plate (114,1)
! Initialization of power window (type
A)
If the vehicle’s battery is disconnected due to situations such as battery or fuse replacement, the following functions are deactivated. . One-touch auto up/down function . Anti-entrapment function
Initialize the power window using the
following procedure to reactivate these
functions.
1. Close the driver’s door.
2. Turn the ignition switch to the “ON”
position.
3. Open the driver’s side window halfway
by pushing down the power window
switch.
4. Pull up the power window switch and
close the window completely. Continue
pulling up the switch for approximately 1
second after the window is closed com-
pletely.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
2
Trunk lid (4-door)
& To open and close the trunk
lid from outside
& To lock and unlock the trunk
lid release lever
Black plate (115,1)
Keys and doors 2-25
WARNING
. To prevent dangerous exhaust gas from entering the vehicle, always keep the trunk lid closed while driving.
. Help prevent children, adults or animals from locking themselves in the trunk. On hot or sunny days, the temperature in the trunk could quickly become high enough to cause death or serious heat-related injuries including brain damage to anyone locked inside, particularly for small chil- dren.
. When leaving the vehicle, either close all windows and lock all doors. Also make certain that the trunk is closed.
The trunk lid can be opened using the remote keyless entry system. Refer to “Remote keyless entry system” F2-8. To close the trunk lid, trunk lid down until the latch engages. NOTE Do not trunk when you leave your vehicle.
leave your valuables in the
lightly press the
& To open the trunk lid from
inside
Pull the trunk lid release lever upward.
When you entrust your vehicle key to another person, you can lock the trunk lid release lever to prevent luggage in the trunk from being stolen. To lock the trunk lid release lever, insert the master key or submaster key into the key cylinder at the rear of the release lever and turn it counterclockwise. Then, entrust the per- son with the valet key only. To unlock the trunk lid release lever, turn the key clock- wise.
& Internal trunk lid release
handle
The internal trunk lid release handle is a device designed to open the trunk lid from
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
2-26 Keys and doors
inside the trunk. In the event children or adults become locked inside the trunk, the handle allows them to open the lid. The handle is located on the inside of the trunk lid.
To open the trunk lid from inside the trunk, pull the yellow handle upward as indicated by the arrow on the handle. This operation unlocks the trunk lid. Then, push up the lid.
that The handle is made of material remains luminescent for approximately an hour in the dark trunk space after it is exposed to ambient light even for a short time.
WARNING
Never allow any child to get in the trunk and play with the release handle. If the driver starts the vehi- cle without knowing that a child is inside the trunk and the child opens the lid using the release handle, the child could fall out and be killed or seriously injured.
CAUTION
. Do not close the lid while grip- ping the release handle. The handle may be damaged.
. Do not use the handle as a hook to fasten straps or ropes to secure your cargo in the trunk. Such use may result in damage of the handle.
. Load the trunk so that cargo can not strike the release handle. If the cargo hits the handle while the vehicle is being driven, the handle may be pulled up and the trunk lid may open. That may cause cargo to fall out of the trunk, which could create a traffic safety hazard.
Black plate (116,1)
! Inspection Perform the following steps at least twice a year to check the release handle for correct operation. 1. Open the trunk lid.
2. Use a flat-head screwdriver with a thin blade. Slide the screwdriver blade from the slit aperture of the lock assembly to the end until you hear a click.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
If the latch is not released, contact your SUBARU dealer. In that case, use the key to release the latch, then close the trunk lid. Also, the release handle feels restricted or not entirely smooth during operation, or the handle and/or handle base is cracked, contact your SUBARU dealer.
the movement of
if
This places the latch in the locked posi- tion.
3. Move the release handle, from outside the vehicle, in the direction of the arrow to check if the latch is released.
Black plate (117,1)
Keys and doors 2-27
Rear gate (5-door)
The rear gate can be locked and unlocked using any of the following systems. . Power door locking switch: Refer to “Power door locking switches” F2-6. . Remote keyless entry system: Refer to “Remote keyless entry system” F2-8.
To open: First unlock the rear gate lock then push the rear gate opener button.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
2-28 Keys and doors
To close: Lower the rear gate slowly and push down firmly until the latch engages. The rear gate can be lowered easily if you pull it down holding the recessed grip.
WARNING
. To prevent dangerous exhaust gas from entering the vehicle, always keep the rear gate closed while driving.
. Do not attempt to shut the rear gate while holding the recessed grip. Also avoid closing the rear gate by pulling on the recessed grip from inside the cargo space. There is a danger of your hand being caught and injured.
CAUTION
. Do not jam a plastic bag in or place cellophane tape on the rear gate stays or scratch the stays while loading or unloading cargo. That could cause leakage of gas from the stays, which may result in their inability to hold the rear gate open.
. Be careful not to hit your head or face on the rear gate when open- ing or closing the rear gate and when loading or unloading car- go.
Black plate (118,1)
NOTE If the rear gate cannot be unlocked due to a discharged vehicle battery, a malfunction in the door locking/unlock- ing system or other causes, you can unlock it by manually operating the rear gate lock release lever. For the procedure, refer to “Rear gate – if the rear gate cannot be unlocked” F9-18.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Moonroof (if equipped)
WARNING
Never let anyone’s hands, arms, head or any objects protrude from the moonroof. A person could be seriously injured if the vehicle stops suddenly or turns sharply or if the vehicle is involved in an accident. To avoid serious personal injury caused by entrapment, always con- form to the following instructions without exception. . Before closing the moonroof, make sure that no one’s hands, arms, head or other objects will be accidentally caught in the moonroof.
. Before leaving the vehicle, al- ways remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operat- ing the moonroof.
Black plate (119,1)
Keys and doors 2-29
. Never try to check the anti-en- trapment function by deliberately placing part of your body in the moonroof.
& Moonroof switches ! Tilting moonroof
CAUTION
. Do not sit on the edge of the open
moonroof.
. Do not operate the moonroof if falling snow or extremely cold conditions have caused it to freeze shut.
. The anti-entrapment
function does not operate when the moon- roof is being tilted down. Be sure to confirm that it is safe to do so before tilting the moonroof down.
The moonroof has both tilting and sliding functions.
The moonroof operates only when the ignition switch is in the “ON” position.
1) Raise 2) Lower
The tilting function will only operate when the moonroof is fully closed.
Push the rear side of switch to raise the moonroof. Push the front side of switch to lower the moonroof.
the “UP/DOWN”
the “UP/DOWN”
Release the switch after the moonroof has been raised or has been lowered com- pletely. Pushing the switch continuously may cause damage to the moonroof.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
2-30 Keys and doors
NOTE One-touch operation does not take place when the moonroof is lowered. Push the switch continuously to raise and lower the moonroof. ! Sliding moonroof
1) Open 2) Close
Push the “OPEN/CLOSE” switch rearward to open the moonroof. The sun shade will also be opened together with the moon- roof. Push the “OPEN/CLOSE” switch forward to close the moonroof. To stop the moonroof at a selected mid- way position while opening or closing it, momentarily push the switch to the “OPEN” side or “CLOSE” side.
After washing the vehicle or after it rains, wipe away water on the roof prior to opening the moonroof to prevent drops of water from falling into the passenger compartment. ! Anti-entrapment function When the moonroof senses a substantial enough object trapped between its glass and the vehicle’s roof during closure, it automatically moves back to the fully open position and stops there. The anti-entrap- ment function may also be activated by a strong shock on the moonroof even when there is nothing trapped.
CAUTION
Never attempt to test this function using fingers, hands or other parts of your body.
NOTE . For the sake of safety, it is recom- mended that you avoid driving with the moonroof fully opened. . If the moonroof cannot be closed through the switch operation because of system failure, it can be closed manually using a hex-head wrench. For the procedure, refer to “Moonroof – if moonroof cannot be closed” F9-19.
Black plate (120,1)
& Sun shade
The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Ignition switch ..................................................... LOCK.................................................................. Acc..................................................................... ON...................................................................... START ................................................................ Key reminder chime ............................................ Ignition switch light ............................................. Hazard warning flasher....................................... Meters and gauges.............................................. Combination meter illumination ........................... Canceling the function for meter/gauge needle
movement upon turning on the ignition switch...............................................................
3-3
3-3
3-4
3-4
3-4
3-5
3-5
3-5
3-6
3-6
3-6
Meter/Gauge needle illumination setting (turbo
3-7
models except STI)............................................
3-8
Speedometer.......................................................
3-8
Odometer/Trip meter............................................
3-9
Tachometer .........................................................
Fuel gauge......................................................... 3-10
Temperature gauge (turbo models) .....................
3-11
REV indicator light and buzzer (STI)................. 3-11
Setting the alarm-level engine speed................... 3-12
Deactivating the REV alarm system..................... 3-13
Warning and indicator lights ............................. 3-13
Seatbelt warning light and chime ........................ 3-14
SRS airbag system warning light ........................ 3-15
Front passenger’s frontal airbag ON and OFF
indicators......................................................... 3-16
CHECK ENGINE warning light/Malfunction
indicator lamp .................................................. 3-16
Black plate (5,1)
Instruments and controls
Coolant temperature low indicator light (non-
turbo models)/Coolant temperature high warning light (non-turbo models)...................... Charge warning light.......................................... Oil pressure warning light .................................. AT OIL TEMP warning light (AT models).............. Rear differential oil temperature warning light
(STI) ................................................................
Low tire pressure warning light (U.S.-spec.
models) ........................................................... ABS warning light.............................................. Brake system warning light................................ Low fuel warning light ....................................... Hill start assist warning light (MT models – if equipped)/Hill start assist OFF indicator light (STI) ................................................................ Door open warning light .................................... All-Wheel Drive warning light (AT models) .......... Vehicle Dynamics Control operation indicator
light ................................................................
Vehicle Dynamics Control warning light/Vehicle Dynamics Control OFF indicator light/Traction Control OFF indicator light (STI)....................... Security indicator light....................................... SPORT mode indicator light (AT models)............ SI-DRIVE indicator light (STI).............................. Shift-up indicator light (STI) ............................... Select lever/gear position indicator
(AT models) ..................................................... Turn signal indicator lights................................. High beam indicator light ................................... Cruise control indicator light..............................
3-17
3-18
3-18
3-18
3-19
3-19
3-21
3-21
3-22
3-22
3-23
3-23
3-23
3-23
3-25
3-25
3-26
3-26
3-26
3-26
3-26
3-26
北米Model "A1110BE-C" EDITED: 2010/ 11/ 17
Black plate (6,1)
Instruments and controls
Cruise control set indicator light......................... 3-27
Front fog light indicator light (if equipped) .......... 3-27
Headlight indicator light (if equipped) ................. 3-27
Driver’s control center differential auto indicator
light (STI) ......................................................... 3-27
Driver’s control center differential indicator and
warning lights (STI) .......................................... 3-27
REV indicator light (STI) ..................................... 3-28
Clock ................................................................... 3-28
Information display ............................................ 3-29
Outside temperature indicator ............................ 3-29
Current fuel consumption (if equipped) ............... 3-30
Average fuel consumption .................................. 3-30
Turn off display of fuel consumption
indicator .......................................................... 3-31
Light control switch ........................................... 3-31
Headlights.......................................................... 3-32
High/low beam change (dimmer)......................... 3-32
Headlight flasher ................................................ 3-32
Daytime running light system............................. Turn signal lever ................................................ Illumination brightness control......................... Headlight beam leveler (if equipped) ............... Front fog light switch (if equipped) .................. Wiper and washer.............................................. Windshield wiper and washer switches .............. Rear window wiper and washer switch – 5-door ............................................................. Mirrors ................................................................ Inside mirror...................................................... Auto-dimming mirror/compass (if equipped) ....... Auto-dimming mirror/compass with HomeLink®
(if equipped) .................................................... Outside mirrors ................................................. Defogger and deicer.......................................... Tilt/telescopic steering wheel ........................... Horn....................................................................
3-33
3-33
3-33
3-34
3-36
3-36
3-38
3-39
3-40
3-40
3-40
3-41
3-47
3-48
3-50
3-51
北米Model "A1110BE-C" EDITED: 2010/ 11/ 17
Ignition switch
WARNING
. Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, preventing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.
. Before leaving the vehicle, al- ways remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child or others. Children could operate the power windows, the moon- roof or other controls or even make the vehicle move.
CAUTION
Do not attach a large key holder or key case to either key. If it banged against your knees or hands while you are driving, it could turn the ignition switch from the “ON” posi-
if
tion to the “Acc” or “LOCK” posi- tion, thereby stopping the engine. Also, the key is attached to a keyholder or to a large bunch of other keys, centrifugal force may act on it as the vehicle moves, resulting in unwanted turning of the ignition switch.
The ignition switch has four positions: LOCK, Acc, ON and START. NOTE . Keep the ignition switch in the “LOCK” position when the engine is not running. . Using electrical accessories for a long time with the ignition switch in the “ON” or “Acc” position can cause the
Black plate (125,1)
Instruments and controls 3-3
battery to go dead. . If the ignition switch will not move from the “LOCK” position to the “Acc” position, turn the steering wheel slightly to the left and right as you turn the ignition switch.
& LOCK The key can only be inserted or removed in this position. The ignition switch will lock the steering wheel when you remove the key. If turn the steering wheel slightly to the right and left as you turn the key. ! AT models
turning the key is difficult,
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
3-4 Instruments and controls
The key can be turned from “Acc” to “LOCK” only when the select lever is in the “P” position. ! MT models
The key can be turned from “Acc” to “LOCK” only when the key is pushed in
while turning it.
& Acc In this position the electrical accessories (audio, accessory power outlet, etc.) can be used.
& ON This is the normal operating position after the engine is started.
& START The engine is started in this position. The starter cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON” position.
CAUTION
Do not turn the ignition switch to the “START” position while the engine is running.
If your registered key fails to start the engine, pull out the key once (the security indicator light will blink), and then insert the key in the ignition switch and turn it to the “START” position and again try to start the engine.
Black plate (126,1)
NOTE The engine may not start in the follow- ing cases:
. The key grip is touching another key or a metallic key holder.
. The key is near another key that
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
contains an immobilizer transponder. . The key is near or touching another transmitter.
& Key reminder chime The reminder chime sounds when the driver’s door is opened and the ignition switch is in the “LOCK” or “Acc” position.
the following
The chime stops under conditions. . when the ignition switch is turned to the “ON” position . when the key is removed from the ignition switch . when the driver’s door is closed
& Ignition switch light For easy access to the ignition switch in the dark, the ignition switch light illumi- nates when the driver’s door is opened or when the driver’s door is unlocked using the remote keyless entry transmitter.
The light remains illuminated for several tens of seconds and then gradually turns off under the following conditions. . when the driver’s door is closed . when the doors are unlocked using the remote keyless entry transmitter
The light turns off immediately under the
Black plate (127,1)
Instruments and controls 3-5
Hazard warning flasher
following conditions. . when the ignition switch is turned to the “ON” position . when all doors and the rear gate (5- door) are locked using the remote keyless entry transmitter
The hazard warning flasher is used to warn other drivers when you have to park your vehicle under emergency conditions. The hazard warning flasher works regard- less of the position of the ignition switch.
To turn on the hazard warning flasher, push the hazard warning button on the instrument panel. To turn off the flasher, push the button again. NOTE When the hazard warning flasher is on, the turn signals do not work.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
3-6 Instruments and controls
Meters and gauges
NOTE Liquid-crystal displays are used in some of the meters and gauges on the combination meter. You will find their indications hard to see if you wear polarized glasses.
& Combination meter illumina-
tion
When the ignition switch is turned to the “ON” position, the combination meter are illuminated in the following sequence:
the various parts of
Turbo models: 1. Warning lights, indicator lights, meter needles and gauge needles illuminate. 2. Meter needles and gauge needles each show MAX position. 3. Meter needles and gauge needles each show MIN position. 4. Meter and gauge dials, odometer and trip meter back light illuminate. 5. Regular illumination (for driving) be- gins.
Non-turbo models: 1. Warning lights, indicator lights, meter needles, gauge needles, odometer and
Black plate (128,1)
“Acc” position. Press the trip knob to show “ on the odometer and trip meter display.
” or “
”
The display can be switched as shown in the following illustration by pressing the trip knob.
trip meter back light illuminate. 2. Meter needles and gauge needles each show MAX position. 3. Meter needles and gauge needles each show MIN position. 4. Regular illumination (for driving) be- gins.
& Canceling the function for meter/gauge needle move- ment upon turning on the ignition switch
It is possible to activate or deactivate the movement of the meter needles and gauge needles that takes place when the ignition switch is turned to the “ON” position. Turn the ignition switch to the “LOCK” or
*1: STI only ” or *2:
“
”, and “
“ ” cannot be displayed when the ignition switch is in the “ON” position.
” or
“
*3: Turbo models except STI
To change the current setting, press the trip knob for at least 2 seconds.
: Activated
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
if
switch is in the “LOCK” position. The illumination of the needles turns off im- mediately after the ignition switch is turned from the “ON” position to the “LOCK” position. NOTE . Even during the illumination after the driver’s door is opened, the ignition switch is turned to the “ON” position, the combination meter will illuminate as usual. . If the doors are locked by the remote keyless entry system during the illumi- nation after the driver’s door is opened, the illumination will be turned off. . Even while the illumination gradu- ally turns off after the ignition switch is turned to the “LOCK” position, if the ignition switch is turned to the “ON” position, the combination meter illumi- nate as usual. To change the setting: 1. Turn the ignition switch to the “LOCK” or “Acc” position.
: Deactivated
NOTE . Your vehicle’s initial movement setting of the meter/gauge needles has been set for activation “ ” at the time of shipment from the factory. . It is not possible to cancel the initial movement setting of the meter/gauge needles when the ignition switch is in the “ON” position. Cancel the setting when the ignition switch is in the “LOCK” or “Acc” position.
& Meter/Gauge needle illumi-
nation setting (turbo models except STI)
When the setting is activated or deacti- vated, the meter needles and gauge needles illuminate and turn off as follows.
Activated: When the driver’s door is opened while the ignition switch is in the “LOCK” position, the needles illuminate and turn off after approximately 20 seconds. The illumination of the needles gradually turns off after the ignition switch is turned from the “ON” position to the “LOCK” position. Deactivated: The needles do not illuminate when the driver’s door is opened while the ignition
Black plate (129,1)
Instruments and controls 3-7
2. Press the trip knob to show “ ” or “ ” on the odometer and trip meter display. The display can be switched as shown in the following illustration by pressing the trip knob.
*: “
” or “
”, and “
” or “
” cannot
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (130,1)
3-8 Instruments and controls
be displayed when the ignition switch is in the “ON” position.
3. To change the current setting, press the trip knob for at least 2 seconds.
: Activated : Deactivated
NOTE The initial illumination setting of the meter/gauge needles of your vehicle has been set for activation “ ” at the time of shipment from the factory. & Speedometer The speedometer shows the vehicle speed.
& Odometer/Trip meter
the “LOCK”, “Acc” or “ON” position.
If you press the trip knob when the ignition switch is in the “LOCK” position, the odometer/trip meter will light up. is possible to switch the indications while the odometer/trip meter is lit up. If you do not press the trip knob within 10 seconds of illumination of the odometer/trip meter, the odometer/trip meter will turn off.
It
The display can be switched as shown in the following illustration by pressing the trip knob.
Turbo models
Non-turbo models 1)
Trip knob
This meter displays the odometer and two trip meters when the ignition switch is in
*1: STI only ” or *2:
“ ” cannot be displayed when the ignition
”, and “
” or
“
“
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
switch is in the “ON” position.
*3: Turbo models except STI ! Odometer
! Double trip meter
The odometer shows the total distance that the vehicle has been driven.
The trip meter shows the distance that the
vehicle has been driven since you last set
it to zero.
To set the trip meter to zero, select the A
trip or B trip meter by pushing the knob
and keep the knob pushed for more than 2
seconds.
CAUTION
To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result.
NOTE If the connection between the combina-
Black plate (131,1)
Instruments and controls 3-9
tion meter and battery is broken for any reason such as vehicle maintenance or fuse replacement, the data recorded on the trip meter will be lost.
& Tachometer The tachometer shows the engine speed in thousands of revolutions per minute.
CAUTION
Do not operate the engine with the pointer of the tachometer in the red zone. This may cause severe da- mage to the engine.
NOTE For non-turbo models, to protect the engine while the select lever is in the “P” or “N” position (for AT models) or the shift lever is in the neutral position (for MT models), the engine is con- trolled so that the engine speed may not become too high even if the accel- erator pedal is depressed hard.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
3-10 Instruments and controls
& Fuel gauge
Turbo models
When the ignition switch is in the “LOCK” or “Acc” position, the fuel gauge shows “E” even if the fuel tank contains fuel.
The gauge may move slightly during
braking, turning or acceleration due to fuel
level movement in the tank.
If you press the trip knob while the ignition
switch is in the “LOCK” or “Acc” position,
the fuel gauge will light up and indicate the
amount of fuel remaining in the tank.
If, while the fuel gauge is indicating the
amount of fuel remaining in the tank, you
(a) do not press the trip knob for 10
seconds or (b) open and close the driver’s
door, the fuel gauge indication will turn off.
NOTE
Non-turbo models 1)
Low fuel warning light
The fuel gauge shows the approximate amount of fuel remaining in the tank.
Black plate (132,1)
” sign in the fuel
You will see the “ gauge meter. This indicates that the fuel filler door (lid) is located on the right side of the vehicle. ! Low fuel warning light The low fuel warning light illuminates when the tank is nearly empty [approxi- mately 2.6 US gal (10.0 liters, 2.2 Imp gal)].
It only operates when the ignition switch is in the “ON” position. NOTE This light does not turn off unless the tank is replenished up to an internal fuel quantity of approximately 4.0 US gal (15 liters, 3.3 Imp gal).
CAUTION
Promptly put fuel in the tank when- ever the low fuel warning light illuminates. Engine misfires as a result of an empty tank could cause damage to the engine.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (133,1)
& Temperature gauge (turbo
models)
CAUTION
If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possible. Refer to “Engine overheating” F9- 13.
Instruments and controls 3-11
REV indicator light and buz- zer (STI)
1) Normal operating range
The temperature gauge shows engine coolant temperature when the ignition switch is in the “ON” position.
The coolant temperature will vary in accordance with the outside temperature and driving conditions.
We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range. Engine operation is optimum with the engine coolant at this temperature range and high revving operation when the engine is not warmed up enough should be avoided.
light
The REV alarm system issues a warning using the REV indicator (and a buzzer if additionally selected) when the engine speed reaches a level previously set using the trip knob. If you press the trip knob, the odometer/ trip meter will show the engine speed that has already been set.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (134,1)
3-12 Instruments and controls
NOTE Even if the REV alarm system is not set, the REV indicator light will illuminate whenever the engine speed enters the tachometer’s red zone.
& Setting the alarm-level en-
gine speed
1. Push the trip knob to select “REV” on the combination meter.
2. When the trip knob is pushed for more than 2 seconds, the thousands place flashes. 3. Release your finger from the trip knob once, then push and hold the trip knob again. The number will change sequen- tially from 2 to 7. Release your finger at the desired alarm-level engine speed.
the
4. When the trip knob is pushed,
hundreds place flashes.
5. Release your
from trip knob
finger
once, then push and hold the trip knob
again. The number will change sequen-
tially from 0 to 9. Release your finger at
the desired alarm-level engine speed.
6. When the trip knob is pushed,
the
buzzer sounds and the REV alarm system
will automatically enter
its new setting
mode (step 7 below), in which you can
activate or deactivate the buzzer.
7. Every time that the trip knob is pushed and held, the buzzer changes to activate or deactivate. b – on: Activated b – off: Deactivated When the mode is changed to “activate”, the buzzer sounds. 8. Push the trip knob to complete the setting procedure.
NOTE . The REV alarm system does not operate while settings are being en- tered. . The speed-setting mode terminates if “--00” rpm is selected. . The speed-setting mode is canceled if the ignition switch is turned from ON
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
to OFF, OFF to ON, or the vehicle starts moving before the setting procedure is finished. . Setting the speed is impossible when the vehicle is moving. . The set engine speed may differ from the engine speed shown by the tachometer. Use the engine speed shown by the tachometer as a rough guide. . If the setting operation is performed with the engine switch turned off, the REV indicator light turns off and the setting operation is aborted when you have stopped the setting operation for approximately 10 seconds. . If the setting operation is performed with the engine switch turned off, the REV indicator light turns off and the setting operation is aborted when you open and close the driver’s door. & Deactivating the REV alarm
system
To deactivate the REV indicator light and buzzer functions of the REV alarm system, set the thousands place of the alarm-level engine speed to “–”.
Warning and indicator lights
Several of the warning and indicator lights illuminate momentarily and then turn off when the ignition switch is initially turned to the “ON” position. This permits check- ing the operation of the bulbs. Apply the parking brake and turn the ignition switch to the “ON” position. For the system check,