Login- Download PDF Manual
-
operating the starter for 5 to 10
seconds, wait for 10 seconds or more before trying again.NOTE . It may be difficult to start the engine when the battery has been discon- nected and reconnected (for mainte- nance or other purposes). This diffi- culty is caused by the electronically controlled throttle’s self-diagnosis function. To overcome it, keep the ignition switch in the “ON” position for approximately 10 seconds before starting the engine. . For non-turbo models, to protect the engine while the shift lever is in the neutral position (MT models)/select lever is in the “P” or “N” position (AT models), the engine is controlled so that the engine speed may not become too high even if the accelerator pedal is depressed hard.
& MT models 1. Apply the parking brake. 2. Turn off unnecessary lights and ac- cessories. 3. Depress the clutch pedal to the floor and shift the shift lever into neutral. Hold the clutch pedal to the floor while starting the engine. The starter motor will only operate when the clutch pedal is depressed fully to the floor. 4. Turn the ignition switch to the “ON” position and check the operation of the lights. Refer warning and indicator to “Warning and indicator lights” F3-13. 5. Turn the ignition switch to the “START” position without depressing the accelera- tor pedal. Release the key immediately after the engine has started. If following.
the engine does not start,
try the
for at
(1) Turn the ignition switch to the “OFF” position and wait least 10 seconds. After checking that the parking brake is firmly set, turn the ignition switch to the “START” position while depressing the accelerator pedal slightly (approximately a quarter of the full stroke). Release the accelerator pedal as soon as the engine starts. (2) If this fails to start the engine, turn
Black plate (277,1)
Starting and operating 7-9
for at
the ignition switch back to the “OFF” position and wait least 10
seconds. Then fully depress the accel- erator pedal and turn the ignition switch to the “START” position. If the engine starts, quickly release the accelerator pedal. (3) If this fails to start the engine, turn the ignition switch again to the “OFF” position. After waiting for 10 seconds or longer, turn the ignition switch to the “START” position without depressing the accelerator pedal. (4) If the engine still refuses to start, contact your nearest SUBARU dealer for assistance.6. Confirm that all warning and indicator lights have turned off after the engine has started. The fuel injection system auto- matically lowers the idle speed as the engine warms up.
& AT models 1. Apply the parking brake. 2. Turn off unnecessary lights and ac- cessories. 3. Shift the select lever to the “P” or “N” position (preferably the “P” position). The starter motor will only operate when the select lever is at the “P” or “N” position. 4. Turn the ignition switch to the “ON”
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
7-10 Starting and operating
position and check the operation of the warning and indicator lights. Refer to “Warning and indicator lights” F3-13. 5. Turn the ignition switch to the “START” position without depressing the accelera- tor pedal. Release the key immediately after the engine has started.
the engine does not start,
If following.
try the
for at
(1) Turn the ignition switch to the “OFF” position and wait least the 10 seconds. After checking that parking brake is firmly set, turn the ignition switch to the “START” position while depressing the accelerator pedal slightly (approximately a quarter of the full stroke). Release the accelerator pedal as soon as the engine starts. (2) If this fails to start the engine, turn the ignition switch back to the “OFF” position and wait least 10
seconds. Then fully depress the accel- erator pedal and turn the ignition switch to the “START” position. If the engine starts, quickly release the accelerator pedal. (3) If this fails to start the engine, turn the ignition switch again to the “OFF” position. After waiting for 10 seconds or longer, turn the ignition switch to the “START” position without depressing the accelerator pedal.for at
Black plate (278,1)
(4) If the engine still refuses to start, contact your nearest SUBARU dealer for assistance.
6. Confirm that all warning and indicator lights have turned off after the engine has started. The fuel injection system auto- matically lowers the idle speed as the engine warms up.
While the engine is warming up, make sure that the select lever is at the “P” or “N” position and that the parking brake is applied.
CAUTION
If you restart the engine while the vehicle is moving, shift the select lever into the “N” position. Do not attempt to place the select lever of a moving vehicle into the “P” posi- tion.
Stopping the engine
The ignition switch should be turned off only when the vehicle is stopped and the engine is idling.
WARNING
Do not stop the engine when the vehicle is moving. This will cause loss of power to the power steering and the brake booster, making steer- ing and braking more difficult. It could also result in accidental acti- vation of the “LOCK” position on the ignition switch, causing the steering wheel to lock.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Remote engine start system (dealer option)
WARNING
(e.g.,
. Do not start the engine using the remote start system in an en- closed environment in a closed garage). Prolonged opera- tion of a motor vehicle in an enclosed environment can cause a harmful build-up of Carbon Monoxide. Carbon Monoxide is harmful to your health. Exposure to high levels of Carbon Monox- ide can cause headaches, dizzi- ness or in extreme cases uncon- sciousness and/or death.
. Before performing any servicing of the vehicle, temporarily place the remote engine start system in service mode to prevent the system from unexpectedly start- ing the engine.
& Starting your vehicle The remote engine start system is acti- vated by pressing the “ ” button twice within 3 seconds on your remote engine start transmitter. The system will check certain pre-conditions before starting, and if all safety parameters are correct, the engine will start within 5 seconds. While the vehicle is operating via remote engine start, the vehicle’s power window features will be disabled. Also, the system has a timer and will shut down after 15 minutes if you do not operate the vehicle. Press and hold the “ ” button for 2 seconds again to turn the vehicle off. If the vehicle’s starter cranks but does not start or starts and stalls, the remote engine start system will power off then attempt to start the vehicle
Black plate (279,1)
Starting and operating 7-11
an additional four times. If the vehicle fails to start after the additional attempts, the remote engine start system will abort and return to a non-activated state.
& Remote start safety features For safety and security reasons, the system will fail to start and beep the horn twice or shut down the engine during remote start operation if any of the following conditions occur. . The brake pedal is depressed before the vehicle ignition switch is turned “on”. . The key was already in the ignition switch. . The engine hood is opened. . The vehicle’s engine idle speed has reached a level over 3,000 rpm. . The alarm is triggered by opening a door or the rear gate. NOTE . The security indicator light on the combination meter will stop flashing while under remote engine start opera- tion, but the vehicle is still protected. . If the vehicle is entered during remote engine start operation, the system will not record entry in the alarm history.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (280,1)
7-12 Starting and operating
& Entering the vehicle while it is running via remote start
turn off.
1. Unlock the vehicle doors using the remote keyless entry system. If the vehi- cle’s doors are unlocked manually using the key, the vehicle’s alarm system will trigger and the remote engine start system will Inserting the key into the ignition switch and turning it to the “ON” position or pressing the unlock button “ ” on the remote keyless entry transmitter will disarm the alarm system. Refer to “Alarm system” F2-16. 2. Enter the vehicle. Do not depress the brake pedal. 3. Insert the key into the ignition switch and turn to the “ON” position. If the ignition switch is accidentally turned to the “START” position, the system’s “starter anti-grind” feature will prevent the starter from re-cranking. 4. Depress the brake pedal. The remote the vehicle’s power starter disengages, window features are re-enabled and the vehicle will operate normally.
& Entering the vehicle follow-
ing remote engine start shut- down
An alarm trigger may occur if the vehicle is opened by the remote keyless entry
transmitter within a few seconds immedi- ately following remote engine start shut- down.
& Pre-heating or pre-cooling the interior of the vehicle
Before exiting the vehicle, set the tem- perature controls to the desired setting and operation. After the system starts the vehicle, the heater or air-conditioning will activate and heat or cool the interior to your setting.
& Service mode In service mode, the remote start function is temporarily disabled to prevent the system from unexpectedly starting the engine while being serviced. ! To engage the service mode Turn the ignition switch to the “ON” position, depress and hold the brake ” pedal, button on the remote engine start trans- mitter three times. The system will pause for 1 second and then flash the turn signal lights and honk the horn three times indicating that the system is in service mode. When attempting to activate the remote start system while in service mode, the turn signal lights will flash and the horn will honk two times and will not
then press and release the “
then press and release the “
start. ! To disengage the service mode Turn the ignition switch to the “ON” position, depress and hold the brake ” pedal, button on the remote engine start trans- mitter three times. The system will pause for 1 second and flash the turn signal lights once indicating that the system has exited service mode. NOTE When taking your vehicle in for service, it is recommended that you inform the service personnel that your vehicle is equipped with a remote engine start system.
& Remote engine start trans-
mitter programming and pro- grammable feature option
New transmitters can be programmed to the remote engine start system in the event that remote engine start transmitters are lost, stolen or damaged. The remote engine start system also has one pro- grammable feature that can be adjusted for user preference. The remote engine start system can be programmed to either make an audible horn chirp upon remote start activation or
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Insert the key into the vehicle’s ignition
not. Remote engine start transmitter pro- gramming and feature programming can be adjusted using the following procedure. 1. Open the driver’s door (the driver’s door must remain opened throughout the entire process). 2. switch and turn to the “ON” position. 3. Locate the small black programming button behind the fuse box cover, on the driver’s side left under the dashboard panel. 4. Press and hold the black programming button for 10 to 15 seconds. The horn will honk and the turn signal lights will flash three times to indicate that the system has entered programming mode. At this point you can proceed to either step 5 or step 6. 5. To program a remote engine start transmitter: press and release the “ ” button on each transmitter. The horn will honk and the turn signal lights will flash one time to indicate a successful trans- mitter learn each time the “ ” button is pressed. You can program up to eight transmitters. 6. To toggle the Horn Confirmation chirps ON/OFF: depress and release the brake pedal to toggle the feature. The horn will chirp and the turn signal lights will flash one time to indicate Confirmation Horn Chirps are “OFF”. The horn will honk and
the turn signal lights will flash 2 times to indicate Confirmation Horn Chirps are “ON”. Depressing the brake pedal repeat- edly will toggle the feature ON or OFF each time. 7. To exit the remote engine start trans- mitter and feature programming mode, turn the ignition switch to the “LOCK” position, remove the key from the ignition switch and test operation of the remote engine start transmitter(s) and horn con- firmation feature.
& System maintenance ! Changing the batteries
CAUTION
. Do not let dust, oil or water get on or in the remote engine start transmitter when replacing the battery.
. Be careful not
to damage the printed circuit board in the re- mote engine start transmitter when replacing the battery.
. Be careful not to allow children to touch the battery and any re- moved parts; children could swallow them.
. There is a danger of explosion if
Black plate (281,1)
Starting and operating 7-13
an incorrect replacement battery is used. Replace only with the same or equivalent type of bat- tery.
. Batteries should not be exposed to excessive heat such as sun- shine, fire or the like.
The two 3-volt lithium batteries (model CR-1220) supplied in your remote engine start transmitter should last approximately 3 years, depending on usage. When the batteries begin to weaken, you will notice a decrease in range (distance from the vehicle that your remote engine start system operates). Follow the instructions below to change the remote engine start transmitter batteries.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
7-14 Starting and operating
1. Carefully pry the remote engine start transmitter halves apart using a small flat- head screwdriver.
Black plate (282,1)
pressly approved by the party re- sponsible for compliance could void the user’s authority to operate the equipment.
NOTE This device complies with Part 15 of the FCC Rules and RSS-Gen of IC to the Rules. Operation is subject following two conditions: (1) this de- vice may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
2. Remove the circuit board from the bottom half of the case and slide the white plastic battery holder out from under the battery tab releasing the batteries. Re- move the old batteries and replace with new ones. Be sure to observe the (+) sign on the old batteries before removing them to ensure that the new batteries are inserted properly (battery “+” should be pointed away from the transmitter circuit board on both batteries). 3. Carefully snap the case halves back together, then test the remote engine start system.
CAUTION
FCC WARNING Changes or modifications not ex-
Manual transmission – 6
speeds (STI)The manual transmission is a fully syn- chromeshed, 6-forward-speed and 1-re- verse-speed transmission. The shift pattern is shown on the shift lever knob.
Black plate (283,1)
Starting and operating 7-15
WARNING
& Selecting reverse gear
. Do not drive the vehicle with the clutch disengaged (i.e., when the clutch pedal is depressed) or with the shift lever in the neutral position. Engine braking has no effect in either of these condi- tions and the risk of an accident is consequently increased.
. Do not engage the clutch (i.e., release the clutch pedal) sud- denly when starting the vehicle. By doing so the vehicle might unexpectedly accelerate or the transmission could malfunction.
1) Slider
You must raise the slider and hold it in that position before you can move the shift lever to the “R” position.
To change gears, fully depress the clutch pedal, move the shift lever, and gradually let up on the clutch. If it is difficult to shift into gear, put the transmission in neutral, release the clutch pedal momentarily, and then try again.
CAUTION
Shift into reverse ONLY when the vehicle has completely stopped. It may cause damage to the transmis- sion to try shifting into reverse when
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
7-16 Starting and operating
the vehicle is moving.
economy.
& Shifting speeds ! Recommended shifting speeds The best compromise between fuel econ- omy and vehicle performance during normal driving is ensured by shifting up at the speeds listed in the following table.
Shift up
1st to 2nd
2nd to 3rd
3rd to 4th
4th to 5th
5th to 6th
mph (km/h)
15 (24)
25 (40)
40 (64)
45 (72)
50 (80)
! Maximum allowable speeds The following table shows the maximum speeds that are possible with each differ- ent gear. The tachometer’s needle will enter the red area if these speeds are exceeded. With the exception of cases where sudden acceleration is required, the vehicle should not be driven with the tachometer’s needle inside the red area. Failure to observe this precaution can lead to excessive engine wear and poor fuel
Gear
1st
2nd
3rd
4th
mph (km/h)
31 (50)
50 (81)
74 (119)
99 (159)
WARNING
When shifting down a gear, ensure that the vehicle is not travelling at a speed exceeding the Maximum Al- lowable Speed for the gear which is about to be selected. Failure to observe this precaution can lead to engine over-revving and this in turn can result in engine damage. In addition, sudden application of engine brakes when the vehicle is travelling on a slippery surface can lead to wheel locking; as a conse- quence, control of the vehicle may be lost and the risk of an accident increased.
NOTE Never exceed posted speed limits.
Black plate (284,1)
& Driving tips Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standstill on an upgrade. Either of those actions may cause clutch damage. Do not drive with your hand resting on the shift lever. This may cause wear on the transmission components.
When it is necessary to reduce vehicle speed due to slow traffic, turning corners, or driving up steep hills, downshift to a lower gear before the engine starts to labor.
On steep downgrades, downshift the transmission to 5th, 4th, 3rd or 2nd gear as necessary; this helps to maintain a safe speed and to extend brake pad life. In this way, the engine provides a braking effect. Remember, if you “ride” (over use) the brakes while descending a hill, they may overheat and not work properly.
The engine may, on rare occasions, knock when the vehicle rapidly accelerates or rapidly pulls away from a standstill. This phenomenon does not indicate a malfunc- tion.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Manual transmission – 5
speeds (except STI)The manual transmission is a fully syn- chromeshed, 5-forward-speed and 1-re- verse-speed transmission. The shift pattern is shown on the shift lever knob. When shifting from 5th gear to reverse gear, first return the shift lever to the neutral position then shift into reverse gear.
To change gears, fully depress the clutch pedal, move the shift lever, and gradually let up on the clutch pedal. If it is difficult to shift into gear, put the transmission in neutral, release the clutch pedal momentarily, and then try again.
WARNING
. Do not drive the vehicle with the clutch disengaged (i.e., when the clutch pedal is depressed) or with the shift lever in the neutral position. Engine braking has no effect in either of these condi- tions and the risk of an accident is consequently increased.
. Do not engage the clutch (i.e., release the clutch pedal) sud- denly when starting the vehicle. By doing so the vehicle might unexpectedly accelerate or the transmission could malfunction.
CAUTION
Shift into reverse ONLY when the vehicle has completely stopped. It may cause damage to the transmis- sion to try shifting into reverse when the vehicle is moving.
Black plate (285,1)
Starting and operating 7-17
& Shifting speeds ! Recommended shifting speeds The best compromise between fuel econ- omy and vehicle performance during normal driving is ensured by shifting up at the speeds listed in the following table.
Shift up
1st to 2nd
2nd to 3rd
3rd to 4th
4th to 5th
mph (km/h)
15 (24)
25 (40)
40 (64) 45 (72)
! Maximum allowable speeds The following tables show the maximum speeds that are possible with each differ- ent gear.
Never exceed the speed limit listed in the following table for each gear position except for brief acceleration in an emer- gency. The tachometer’s needle will enter the red area if these speeds are ex- ceeded. Failure to observe this precaution can lead to excessive engine wear and poor fuel economy.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (286,1)
7-18 Starting and operating
Non-turbo models
1st
2nd
3rd
Turbo models
1st
2nd
3rd
mph (km/h)
32 (51)
53 (86) 76 (122)
mph (km/h)
35 (56)
58 (94) 85 (137)
WARNING
When shifting down a gear, ensure that the vehicle is not travelling at a speed exceeding the Maximum Al- lowable Speed for the gear which is about to be selected. Failure to observe this precaution can lead to engine over-revving and this in turn can result in engine damage. In addition, sudden application of engine brakes when the vehicle is travelling on a slippery surface can lead to wheel locking; as a conse- quence, control of the vehicle may be lost and the risk of an accident increased.
NOTE Never exceed the posted speed limit.
Driver’s Control Center Dif- ferential (DCCD) (STI)
& Driving tips Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standstill on an upgrade. Either of those actions may cause clutch damage. Do not drive with your hand resting on the shift lever. This may cause wear on the transmission components.
When it is necessary to reduce vehicle speed due to slow traffic, turning corners, or driving up steep hills, downshift to a lower gear before the engine starts to labor.
the On steep downgrades, downshift transmission to 4th, 3rd or 2nd gear as necessary; this helps to maintain a safe speed and to extend brake pad life. In this way, the engine provides a braking effect. Remember, if you “ride” (over use) the brakes while descending a hill, they may overheat and not work properly.
The engine may, on rare occasions, knock when the vehicle rapidly accelerates or rapidly pulls away from a standstill. This phenomenon is not an indication of a problem in your vehicle.
WARNING
Always use the utmost care when driving. Being overconfident be- cause you are driving a vehicle with a driver’s control center differential could easily lead to a serious acci- dent.
CAUTION
All the indicator lights will flash in the event that the driver’s control center differential has a malfunc- tion. Have the vehicle inspected by your SUBARU dealer.
limitation of
The driver’s control center differential allows you to freely change the degree of the differential action (limited slip differential (LSD) torque) of your vehicle’s center differential. By using the center differential control switch, you can set an initial LSD torque to match the road surface conditions, driving conditions and your driving style.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (287,1)
Starting and operating 7-19
& Auto mode
tial and rear differential. This sound occurs because of the structure of the center differential. It does not indicate a problem.
& To change mode of driver’s
control center differential
LSD torque Traction torque Initial LSD torque (maximum) Initial LSD torque (minimum) Initial LSD torque (adjustable)
1) 2) 3) 4) A) B) Mechanical LSD torque
The driver’s control center differential has an auto mode and a manual mode. In the the system automatically auto mode, adjusts the initial LSD torque. In the manual mode, you can change to the desired mode manually by using the center differential control switch. NOTE If you rapidly depress and release the accelerator pedal while driving at low speed, you may hear a knocking sound from the vicinity of the center differen-
In the auto mode, the system estimates the driving and road conditions using signals from the wheel speed sensor, throttle position sensor, steering angle sensor and brake switch, etc. According to the result, it electronically and auto- matically controls the degree of limitation of the differential action (LSD torque) to optimize the differential action of the center differential. When the ignition switch is turned ON, the “AUTO” indicator light on the combination meter illuminates.
Press the “AUTO-MANU” switch on the center console to switch from auto mode to manual mode or vice versa. When you select the auto mode, the “AUTO” indica- tor light illuminates. When you select the manual mode, the “AUTO” indicator light turns off.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
7-20 Starting and operating
The auto mode has 3 modes as follows.
Mode
AUTO [+]
Operation
This mode emphasizes traction control and strengthens the limitation of differential action that is suitable for driving on slippery roads for vehicle stabi- lity.
AUTO
This mode is suitable for most driving situations.
AUTO [−]
This mode is suitable when you seek quick response from the steering wheel and smooth driving.
! Mode setting method In most situations, it is recommended that the “AUTO” mode is selected.
Push the control switch forward to select
Black plate (288,1)
the “AUTO [+]” mode. After setting the mode, “ ” on the combination meter illuminates.
& Manual mode
In the manual mode, you can use the center differential control switch to adjust the initial LSD torque as desired. When this mode is selected, the “AUTO” indica- tor light on the combination meter turns off.
Pull the control switch rearward to select the “AUTO [−]” mode. After setting the mode, “ ” on the combination meter illuminates. When the “AUTO [+]” mode is selected, pull the control switch rearward to change to the “AUTO” mode. When the “AUTO [−]” mode is set, push the control switch forward to change to the “AUTO” mode.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
! Center differential control switch
and indicator light
Push the switch forward to increase the initial LSD torque; when the “LOCK” indicator light illuminates, the initial LSD torque setting is maximum. The center differential will then be almost completely locked.
The control switch is located beside the parking brake lever. By pushing the control switch forward or pulling it rear- ward, it is possible to change the initial LSD torque. The center differential indicator lights on the combination meter give six levels of indication. The indicator lights and control switch are linked; when the switch is pushed or pulled to change the initial LSD torque, the illumination position of the indicator lights changes accordingly.
Black plate (289,1)
Starting and operating 7-21
Pull the switch rearward to reduce the initial LSD torque. When the lowest posi- tion of the driver’s control center differen- tial the initial LSD torque will be minimum. Under this condition, only the Mechanical LSD torque will limit the differential action.
indicator light
illuminates,
CAUTION
. Do not operate the control switch when a wheel slippage occurs. Wait until the wheelspin has been brought under control.
. Under any of the following con- ditions after setting to the man- ual mode, pull the center differ- ential control switch to minimize the initial LSD torque:
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (290,1)
7-22 Starting and operating
. When a temporary spare tire is
installed
. When your vehicle is towed . When the vehicle is stopped with the manual mode se- lected
NOTE . A higher initial LSD torque setting gives the vehicle greater traction when driving straight ahead but makes cor- nering more difficult. Remember this when adjusting the initial LSD torque. In general, higher initial LSD torque settings assist driving on slippery roads and lower settings for non-slip- pery roads. When the vehicle is stuck in snow or mud, setting the initial LSD torque to the maximum will help to free the vehicle. . The setting of the initial LSD torque will remain even when the auto mode is selected or the ignition switch is turned to the “OFF” position. However, the initial LSD torque will be minimized when the battery is disconnected and reconnected. . During cornering or when making turns (especially when going into the garage), the rotational difference be- tween the front and rear wheels may
cause a braking effect accompanied by vibration and noise. This does not indicate a problem. The phenomenon will disappear when setting the initial LSD torque to the minimum. In the auto mode, it controls the initial LSD torque automatically. While in the auto mode, this phenomenon some- times occurs depending on the driving condition, however, it does not indicate a problem. . Use the center differential indicator light only as a rough indication of the initial LSD torque. . If you operate the center differential control switch while quickly accelerat- ing or turning a tight corner, you may feel slight shocks. This is due to differential action by the center differ- ential and does not indicate a problem.
& Temporary release When the driver stops the vehicle and pulls the parking brake lever after manu- ally setting the initial LSD torque, the LSD torque is temporarily minimized. However the indicator on the combination meter continues to show the driver’s selected initial LSD torque. When the driver re- leases the parking brake lever, the initial LSD torque set by the driver is restored.
Automatic transmission
The automatic transmission is electroni- cally controlled and provides 4 forward speeds and 1 reverse speed. Also, it has a manual mode and a SPORT mode.
WARNING
Do not shift from the “P” or “N” position into the “D” or “R” position while depressing the accelerator pedal. This may cause the vehicle to jump forward or backward.
CAUTION
. Shift into the “P” or “R” position only after the vehicle is comple- tely stopped. Shifting while the vehicle is moving may cause damage to the transmission.
. Do not race the engine for more than 5 seconds in any position except the “N” or “P” position when the brake is set or when chocks are used in the wheels. This may cause the automatic transmission fluid to overheat.
. Avoid shifting from one of the forward driving positions into the
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
“R” position or vice versa until the vehicle has completely stopped. Such shifting may cause damage to the transmis- sion.
. When parking the vehicle, first securely apply the parking brake and then place the select lever in the “P” position. Avoid parking for a long time with the select lever in any other position as doing so could result in a dead battery.
NOTE . When the engine coolant tempera- ture is still low, the automatic transmis- sion will upshift to higher engine speeds than when the coolant tempera- ture is sufficiently high in order to shorten the warm-up time and improve driveability. The gearshift timing will automatically shift to the normal timing after the engine has warmed up. . Immediately after ATF (automatic transmission fluid) is replaced, you may feel that the automatic transmis- sion operation is somewhat unusual. This results from invalidation of data which the on-board computer has collected and stored in memory to
allow the transmission to shift at the most appropriate times for the current condition of your vehicle. Optimized shifting will be restored as the vehicle continues to be driven for a while.
& Select lever
: Shifting is possible with the brake pedal
depressed.
: Shifting is possible whether the brake
pedal is depressed or not. However, while the ignition switch is in the “LOCK” or “Acc” position, shifting is not possible if the brake pedal is not depressed. Depress the brake pedal and move the select lever.
: Shifting is possible whether the brake
pedal is depressed or not.
The select lever has four positions, “P”, “R”, “N”, “D” and also has manual gate for
Black plate (291,1)
Starting and operating 7-23
using “SPORT” mode or manual mode. ! P (Park) This position is for parking the vehicle and starting the engine. In this position, the transmission is me- chanically locked to prevent the vehicle from rolling freely.
When you park the vehicle, first set the parking brake fully, then shift into the “P” position. Do not hold the vehicle with only the transmission. To shift the select lever from the “P” to any other position, you should depress the brake pedal fully then move the select lever. This prevents the vehicle from lurching when it is started. ! R (Reverse) This position is for backing the vehicle. To shift from the “N” to “R” position, stop the vehicle completely then move the lever to the “R” position. ! N (Neutral) This position is for restarting a stalled engine. In this position the wheels and transmis- sion are not locked. In this position, the transmission is neutral; the vehicle will roll freely, even on the slightest incline unless
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (292,1)
7-24 Starting and operating
the parking brake or foot brake is applied. Avoid coasting with the transmission in neutral. During coasting, there is no engine brak- ing effect.
WARNING
Do not drive the vehicle with the lever in the “N” (neutral) select position. Engine braking has no effect in this condition and the risk of an accident is consequently in- creased.
NOTE If the select lever is in the “N” position when you stop the engine for parking, you may not subsequently be able to move it to the “R” or “P” position. If this happens, turn the ignition switch to the “ON” position. You will then be able to move the select lever to the “P” position. For details, refer to “Shift lock function” F7-24. ! D (Drive) This position is for normal driving. The transmission automatically shifts into a suitable gear from 1st to 4th according to the vehicle speed and the acceleration you require.
When more acceleration is required in this position, depress the accelerator pedal fully to the floor and hold that position. The transmission will automatically downshift to 3rd, 2nd or 1st gear. When you release the pedal, the transmission will return to the original gear position. To use the “SPORT” mode, move the lever from this position into the manual gate. To use the manual mode, move the lever from this position into the manual gate then move it toward the “+” and “−” ends. ! While climbing a grade When driving up a hill, undesired upshift to 4th gear is prevented from taking place when the accelerator is released. This minimizes the chance of subsequent downshifting to a lower gear when accel- erating again. This prevents repeated upshifting and downshifting resulting in a smoother operation of the vehicle. NOTE The transmission may downshift to 2nd or 1st gear, depending on the way the accelerator pedal is depressed to ac- celerate the vehicle again. ! While going down a hill When you are descending a hill or any other slope while braking with the “SPORT” mode selected, the transmission
may downshift to 3rd or 2nd gear depend- ing on how hard you depress the brake pedal, causing engine braking to work. Reacceleration for a short time will cause the transmission to upshift normally. NOTE . A 4th-to-3rd automatic downshift will not occur at speeds above 50
mph (80 km/h) and a 3rd-to-2nd auto- matic downshift will not occur at speeds above 24 mph (38 km/h). . Automatic downshifts to 3rd or 2nd may occur even when driving on a level road depending on conditions, such as how hard you depress the brake pedal.& Shift lock function The shift lock function helps prevent the improper operation of the select lever. . The select lever cannot be operated unless the ignition switch is turned to the “ON” position and the brake pedal is depressed. . The select lever cannot be moved from the “P” position to any other position before the brake pedal is depressed. Depress the brake pedal first, and then operate the select lever. . Only the “P” position allows you to turn the key from the “Acc” position to the
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
“LOCK” position and remove the key from the ignition key cylinder. . If the ignition switch is turned to the “LOCK” position while the select lever is in the “N” position, the select lever may not be moved to the “P” position after a period of time. Therefore, move the select lever to the “P” position with the brake pedal depressed soon after the ignition switch is turned to the “LOCK” position.
! Shift lock release If the select lever cannot be operated, turn the ignition switch back to the “ON” position then move the select lever to the “P” position with the brake pedal de- pressed.
the select
lever cannot be
If lever does not move after performing the above procedure, perform the following steps. . When the select shifted from “P” to “N”: Refer to “Shift lock release using the shift lock release button” F7-25. . When the select shifted from “N” to “R”, “P”: Within 60 seconds after placing the igni- tion switch in the “Acc” position, move the select lever to the “R” or “P” position with the brake pedal depressed.
lever cannot be
Black plate (293,1)
Starting and operating 7-25
cover. NOTE To prevent damage to the shift lock cover, cover the tip of the flat-head screwdriver with vinyl tape or a cloth before removing the cover.
If you must perform the above procedure, the shift lock system (or the vehicle control system) may be malfunctioning. Contact a SUBARU dealer for an inspection as soon as possible.
the select
If lever does not move after performing the above procedure, refer to “Shift lock release button” F7-25. ! Shift lock release using the shift
lock release using the shift
lock release button
Perform the following procedure to release the shift lock. 1. Apply the parking brake and stop the engine.
2. Remove the shift lock cover using a flat-head screwdriver. The shift lock re- lease button is located under the shift lock
3. While depressing the brake pedal, insert a screwdriver into the hole, press the shift lock release button using a screwdriver, and then move the select lever.
the select
If lever does not move after performing the above procedure, the shift lock system may be malfunctioning. Con- tact a SUBARU dealer for an inspection as soon as possible.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (294,1)
7-26 Starting and operating
& Selection of manual mode NOTE Please read the following points care- fully and bear them in mind when using the manual mode. . If you attempt to shift down when the engine speed is too high, i.e., when a downshift would push the tachometer needle beyond the red zone, beeps will be emitted to warn you that the down- shift is not possible. . If you attempt to shift up when the vehicle speed is too low, the transmis- sion will not respond. . You can perform a skip-shift (for example, from 4th to 2nd) by operating the select lever twice in rapid succes- sion. . The transmission automatically se- lects 1st gear when the vehicle stops moving. . If the temperature of the automatic transmission fluid becomes too high, the “AT OIL TEMP” warning light will illuminate and upshifts to 4th gear will not be possible. Immediately stop the vehicle in a safe place and let the engine idle until the warning light turns off.
With the vehicle either moving or station- ary, move the select lever from the “D” position to the manual gate then move it to the “+” end or “−” end of the manual gate to select manual mode.
1) Upshift indicator 2) Downshift indicator 3) Gear position indicator
When the manual mode is selected, the gear position indicator and upshift indica- tor and/or downshift indicator on the combination meter illuminate. The gear position indicator shows the currently selected gear in the 1st-to-4th-gear range. The upshift and downshift indicators show when a gear shift is possible. When the ” is illuminated, up- upshift shifting is possible. When the downshift indicator “ ” is illuminated, downshifting is possible. When both indicators are illuminated, upshifting and downshifting are both possible. When the vehicle stops (for example, at traffic signals), the down- shift indicator turns off.
indicator “
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Gear shifts can be performed by using the select lever (all models) or the paddle shift switch behind the steering wheel (if equipped). ! Using the select lever
! Using the paddle shift (if equipped)
to the next-higher gear by briefly lever toward the “+”
Shift pushing the select end of the manual gate. Shift pulling the select lever end of the manual gate.
to the next-lower gear by briefly toward the “−”
Pull the “+” of the paddle shift to upshift one level. Pull the “−” of the paddle shift to downshift one level.
To deselect the manual mode, return the select lever to the “D” position from the manual gate. While driving, if you change the gear by paddle shifting, the gear position indicator illuminates and shows the current gear condition. At this time, the normal mode temporarily changes to the manual mode, and after driving for a short period of time, the transmission mode returns to the normal mode. (The timing of the gear change and return is different, depending on the driving condition when paddle shifting.)
Black plate (295,1)
Starting and operating 7-27
if you subsequently ease off
Also, the accelerator pedal and then accelerate again, the transmission will automatically switch back from manual mode to normal mode.
CAUTION
The paddle shift lever could be accidentally changed if accessories or other materials are placed on the paddle shift. Do not place acces- sories and other materials on the paddle shift lever.
& Driving tips . On a road surface where there is a risk of wheelspin (for example, a snow- or gravel-covered road), you can pull away from a standstill (safely and easily) by first selecting the 2nd gear of the manual mode. . Always apply the foot or parking brake when the vehicle is stopped in the “D” or “R” position. . Always set the parking brake when parking your vehicle. Do not hold the vehicle with only the transmission. . Do not keep the vehicle in a stationary position on an uphill grade by using the “D” position. Use the brake instead.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
7-28 Starting and operating
. The engine may, on rare occasions, knock when the vehicle rapidly acceler- ates or rapidly pulls away from a standstill. This phenomenon does not indicate a problem.
& SPORT mode
When selected, the SPORT mode indica- tor light on the combination meter will illuminate. To deselect SPORT mode, move the select lever to the “D” position or select manual mode. To subsequently reselect SPORT mode, move the select lever to the “D” position and from there to the manual gate. In this mode, the transmission shifts up at higher vehicle speeds and shifts down more responsively than in normal mode.
SPORT mode is used when power is needed for rapid acceleration or for uphill driving. To select this mode, move the select lever from the “D” position to the manual gate.
Black plate (296,1)
SI-DRIVE (STI)
SI-DRIVE (SUBARU Intelligent Drive) works to maximize engine performance, control and efficiency. This system consists of three modes: Intelligent (I), Sport (S), and Sport Sharp (S#). By adjusting the SI-DRIVE selector, the character of the power unit changes.
& Intelligent (I) mode ! For smooth, efficient performance
driving
The Intelligent (I) mode provides well- balanced performance with greater fuel efficiency and smooth driveability without stress. Power delivery is moderate during acceleration for maximum fuel efficiency.
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (297,1)
& Sport (S) mode ! For all-around performance driving
& Sport Sharp (S#) mode ! For maximum performance driving
Starting and operating 7-29
This is ideal for around-town driving and situations that do not require full power output. It provides better control in difficult driving conditions, such as slippery roads or loose surfaces, due to gentler throttle response.
When Intelligent (I) mode is selected, a shift-up indicator “ ” on the combination meter will blink to signal the best time to shift gears for maximum fuel efficiency.
The Sport (S) mode provides the engine power desired by those who want to make the driving experience their own personal adventure. The linear acceleration characteristic of this versatile mode is ideal for normal driving use.
For sports-minded drivers, the Sport Sharp (S#) mode offers an exhilarating level of engine performance and control. The throttle becomes more responsive regardless of the engine speed. Delivering maximum driving enjoyment, this mode is ideal for tackling twisting roads and for merging or overtaking other vehicles on the freeway with confidence.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Black plate (298,1)
there is a possibility that
the same mode as when the engine was turned off. . While the engine is running, if the CHECK ENGINE warning light/malfunc- tion indicator lamp illuminates, the SI- DRIVE mode changes to the Sport (S) mode. In this case, it is not possible to change to the Sport Sharp (S#) mode or Intelligent (I) mode. . If the engine could overheat because of a temperature increase of the engine coolant, it is not possible to change to the Sport Sharp (S#) mode. While the vehicle is in the Sport Sharp (S#) mode, it changes to the Sport (S) mode when the engine coolant temperature in- creases. . If any of the SI-DRIVE indicators the SI-DRIVE system may be blink, malfunctioning. Contact your SUBARU dealer.
Limited slip differential (LSD) (STI)
The LSD provides optimum distribution of power according to the difference in revolutions between the right and left wheels that may be caused by certain driving conditions, thereby improving driv- ing stability on snow-covered, muddy or other slippery roads or when high speed driving.
CAUTION
. Never start the engine while a tire on one side is jacked up, as the vehicle may move.
. If one tire is spinning in mud, avoid continued spinning at high speed as this could adversely affect the LSD.
. If you use a temporary spare tire to replace a flat tire, be sure to use the original temporary spare tire stored in the vehicle. Using other sizes will adversely affect the LSD.
7-30 Starting and operating
& SI-DRIVE selector When you rotate the SI-DRIVE selector to the left, the current SI-DRIVE mode changes to Sport (S) mode. When you rotate it to the right, the mode changes to Sport Sharp (S#) mode, and when you push it, the mode changes to Intelligent (I) mode. After performing this operation, the switch returns to its original location.
NOTE . The next time you turn on the engine, after you turned off the engine in the Sport Sharp (S#) mode, the SI- DRIVE mode changes to the Sport (S) mode. . The next time you turn on the engine, after you turned off the engine in the Sport (S) mode or Intelligent (I) mode, the SI-DRIVE mode will stay in
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
Power steering
The power steering system operates only when the engine is running. If you lose power steering assist because the engine stops or the system fails to function, you can steer but take much more effort.
it will
CAUTION
Do not hold the steering wheel at the fully locked position left or right for more than 5 seconds. This may damage the power steering pump.
NOTE Right after the engine has been started and before it has warmed up, you may hear a noise coming from areas adja- cent to the power steering pump which is located at the right-front area of the engine compartment. This noise is normal. indicate power steering system trouble.
It does not
Braking & Braking tips
WARNING
Never rest your foot on the brake pedal while driving. This can cause dangerous overheating of the brakes and needless wear on the brake pads and linings.
! When the brakes get wet When driving in rain or after washing the vehicle, the brakes may get wet. As a result, brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly depressing the brake pedal to heat up the brakes. ! Use of engine braking Remember to make use of engine braking in addition to foot braking. When descend- ing a grade, if only the foot brake is used, the brakes may start working improperly because of brake fluid overheating, caused by overheated brake pads. To help prevent this, shift into a lower gear to get stronger engine braking. ! Braking when a tire is punctured Do not depress the brake pedal suddenly when a tire is punctured. This could cause
Black plate (299,1)
Starting and operating 7-31
a loss of control of the vehicle. Keep driving straight ahead while gradually reducing speed. Then slowly pull off the road to a safe place.
& Brake system ! Two separate circuits Your vehicle has two separate circuit brake systems. Each circuit works diag- onally across the vehicle. If one circuit of the brake system should fail, the other half of the system still works. If one circuit fails, the brake pedal will go down much closer to the floor than usual and you will need to press it down much harder. And a much longer distance will be needed to stop the vehicle. ! Brake booster The brake booster uses engine manifold vacuum to assist braking force. Do not turn off the engine while driving because that will turn off the brake booster, result- ing in poor braking power. The brakes will continue to work even when the brake booster completely stops functioning. If this happens, however, you will have to depress the pedal much harder than normal and the braking dis- tance will increase.
– CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
7-32 Starting and operating
! Brake assist system
WARNING
Do not be overconfident about the brake assist. It is not a system that brings more braking ability to the vehicle beyond its braking capabil- ity. Always use the utmost care when driving regarding vehicle speed and safe distance.
CAUTION
When you need to brake suddenly, continue depressing the brake pedal strongly to bring the effect of the brake assist.
Brake assist is a driver assistance system. It assists the brake power when the driver cannot depress the brake pedal strongly and the brake power is insufficient. Brake assist generates the brake power according to the speed at which the driver depresses the brake pedal. NOTE When you depress the brake pedal strongly or suddenly, the following phenomena occur. However, even though these occur, they do not indi-
cate any malfunctions, and the brake assist system is operating properly. . You might feel that the brake pedal is applied by lighter force and gener- ates a greater braking force. . You might hear the sound of ABS operating from the engine compart- ment.
& Disc brake pad wear warning
indicators
The disc brake pad wear warning indica- tors on the disc brakes give a warning noise when the brake pads are worn. If a squeaking or scraping noise is heard from the disc brakes while braking, im- mediately have your vehicle checked by your SUBARU dealer.
Black plate (300,1)
ABS (Anti-lock Brake Sys- tem)
The ABS system prevents the lock-up of wheels which may occur during sudden braking or braking on slippery road sur- faces. This helps prevent the loss of steering control and directional stability caused by wheel lock-up.
When the ABS system is operating, you may hear a chattering noise or feel a slight vibration in the brake pedal. This is normal when the ABS operates.
The ABS system will not operate when the vehicle speed is below approximately 6
mph (10 km/h).WARNING
Always use the utmost care in driving – overconfidence because you are driving with an ABS equipped vehicle could easily lead to a serious accident.
CAUTION
. The ABS system does not always decrease stopping distance. You should always maintain a safe following distance from other
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
vehicles.
. When driving on badly surfaced roads, gravel roads, icy roads, or over deep newly fallen snow, stopping distances may be long- er for a vehicle with the ABS system than one without. When driving under these conditions, therefore, reduce your speed and leave ample distance from other vehicles.
. When you feel the ABS system operating, you should maintain constant brake pedal pressure. Do not pump the brake pedal since doing so may defeat the operation of the ABS system.
& ABS system self-check Just after the vehicle is started, you may feel on the brake pedal a vibration similar to when the ABS operates, and you may also hear the sound of the ABS working from the engine compartment. This is caused by an automatic functional test of the ABS system being carried out and does not indicate any abnormal condition.
& ABS warning light Refer to “ABS warning light” F3-21.
Black plate (301,1)
Electronic Brake Force Dis- tribution (EBD) system
& Steps to take if EBD system
malfunctions
Starting and operating 7-33
The EBD system maximizes the effective- ness of the brakes by allowing the rear brakes to supply a greater proportion of the braking force. It functions by adjusting the distribution of braking force to the rear wheels in accordance with the vehicle’s loading condition and speed. The EBD system is an integral part of the ABS system and uses some of the ABS system’s components to perform its func- tion of optimizing the distribution of brak- ing force. If any of the ABS components used by the EBD system malfunction, the EBD system also stops working.
When the EBD system is operating, you may hear a chattering noise or feel a slight vibration in the brake pedal. This is normal and does not indicate a malfunction.
Turbo models
Non-turbo models
If a malfunction occurs in the EBD system, the system stops working and the brake – CONTINUED –
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
7-34 Starting and operating
system warning light and ABS warning light illuminate simultaneously.
The EBD system may be malfunctioning if the brake system warning light and ABS warning light illuminate simultaneously during driving. Even if the EBD system malfunctions, the conventional braking system will still func- tion. However, the rear wheels will be more prone to locking when the brakes are applied harder than usual and the vehicle’s motion may therefore become somewhat harder to control. If the brake system warning light and ABS warning light illuminate simultaneously, take the following steps. 1. Stop the vehicle in the nearest safe, flat location. 2. Shut down the engine, apply the parking brake, and then restart it. 3. Release the parking brake. If both warning lights turn off, the EBD system may be malfunctioning. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights illuminate again and remain illuminated after the engine has been restarted, shut down the engine again, apply the parking brake, and check the brake fluid level. Refer to “Brake fluid” F11-25.
If the brake fluid level is not below the 5. “MIN” mark, the EBD system may be malfunctioning. Drive carefully to the nearest SUBARU dealer and have the system inspected. 6. is below the “MIN” mark, DO NOT drive the vehicle. Instead, have the vehicle towed to the nearest SUBARU dealer for repair.
the brake fluid level
If
WARNING
. Driving with the brake system warning light illuminated is dan- gerous. This indicates your brake system may not be working properly. the light remains illuminated, have the brakes in- spected by a SUBARU dealer immediately.
If
. If at all in doubt about whether the brakes are operating prop- erly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for re- pair.
Black plate (302,1)
Vehicle Dynamics Control system
WARNING
Always use the utmost care in driving – overconfidence because you are driving with a Vehicle Dy- namics Control system equipped vehicle could easily lead to a ser- ious accident.
CAUTION
. Even if your vehicle is equipped with Vehicle Dynamics Control system, winter tires should be used when driving on snow-cov- ered or icy roads; in addition, vehicle speed should be reduced considerably. Simply having a Vehicle Dynamics Control sys- tem does not guarantee that the vehicle will be able to avoid accidents in any situation.
. Activation of
the Vehicle Dy- namics Control system is an indication that the road being travelled on has a slippery sur- face; since having Vehicle Dy- namics Control is no guarantee
北米Model "A1110BE-C" EDITED: 2010/ 12/ 17
that full vehicle control will be maintained at all times and under all conditions, its activation should be seen as a sign that the speed of the vehicle should be reduced considerably.
. Whenever suspension compo- nents, steering components, or an axle are removed from a vehicle, have an inspection of that system performed by an authorized SUBARU dealer.
. The following precautions should be observed in order to ensure that the Vehicle Dynamics Con- trol system is operating properly: – All four wheels should be fitted with tires of the same size, type, and brand. Further- more, the amount of wear should be the same for all four tires.
– Keep the tire pressure at the proper level as shown on the vehicle placard attached to the driver’s side door pillar.
– Use only the specified tem- porary spare tire to replace a flat tire. With a temporary spare tire, the effectiveness of the Vehicle Dynamics Con-
trol system is reduced and this should be taken into ac- count when driving the vehi- cle in such a condition.
. If non-matching tires are used, the Vehicle Dynamics Control system may not operate cor- rectly.
. The Vehicle Dynamics Control system helps prevent unstable vehicle motion such as skidding using control of the brakes and engine power. Do not turn off the Vehicle Dynamics Control sys- tem unless it is absolutely ne- cessary. If you must turn off the Vehicle Dynamics Control sys- tem, drive very carefully based on the road surface condition.
In the event of wheelspin and/or skidding on a slippery road surface and/or during cornering and/or an evasive maneuver, the Vehicle Dynamics Control system adjusts the engine’s output and the wheels’ respective braking forces to help maintain traction and directional control. . Traction Control Function The traction control function is designed to prevent spinning of the driving wheels on slippery road surfaces, thereby helping to maintain traction and directional control.
Black plate (303,1)
Starting and operating 7-35
Activation of this function is indicated by steady illumination of the Vehicle Dy- namics Control operation indicator light. . Skid Suppression Function The skid suppression function is designed to help maintain directional stability by suppressing the wheels’ tendency to slide sideways during steering operations. Acti- vation of this function is indicated by flashing of the Vehicle Dynamics Control operation indicator light. NOTE . The Vehicle Dynamics Control sys- tem may be considered normal when the following conditions occur.
the brake
twitching of
– Slight pedal is felt. – The vehicle or steering wheel shakes to a small degree. – An operating sound from the engine compartment is heard briefly when starting the engine and when driving off after starting the engine. – The brake pedal seems to jolt when driving off after starting the engine.
. In the circumstances listed in the the vehicle may be more
