Login- 2002 Subaru Forester Owners Manuals
- Subaru Forester Owners Manuals
- 2000 Subaru Forester Owners Manuals
- Subaru Forester Owners Manuals
- 2011 Subaru Forester Owners Manuals
- Subaru Forester Owners Manuals
- 2009 Subaru Forester Owners Manuals
- Subaru Forester Owners Manuals
- 2012 Subaru Forester Owners Manuals
- Subaru Forester Owners Manuals
- 2001 Subaru Forester Owners Manuals
- Subaru Forester Owners Manuals
- 2010 Subaru Forester Owners Manuals
- Subaru Forester Owners Manuals
- Download PDF Manual
-
harness to protect against possible damage. D Occasionally lubricate terminals of the four–pin connector using the terminal grease.
– CONTINUED –
8-27
Legacy U.S.A..(ENG.)A2290BE–A
Trailer towing
Your car is designed and intended to be used primarily as a passenger- carrying vehicle. Towing a trailer puts additional loads on your car’s en- gine, drivetrain, brakes, tires and suspension and has an adverse effect on fuel economy. If you do decide to tow a trailer, your safety and satisfaction depend upon proper use of correct equipment and cautious operation of your ve- hicle. Seek the advice of your SUBARU dealer to assist you in purchas- ing a hitch and other necessary towing equipment appropriate for your vehicle. In addition, be sure to follow the instructions on correct installa- tion and use provided by the trailer and other towing equipment manufacturers. SUBARU assumes no responsibility for injuries or vehicle damage that result from trailer towing equipment, or from any errors or omissions in the instructions accompanying such equipment or for your failure to fol- low the proper instructions.
B Warranties and maintenance SUBARU warranties do not apply to vehicle damage or malfunction caused by trailer towing. If you use your vehicle to tow a trailer, more frequent maintenance will be required due to the additional load. (Refer to “Maintenance schedule under severe driving conditions” in the “Warranty and Maintenance Booklet”.) Under no circumstances should a trailer be towed with a new vehicle or a vehicle with any new powertrain component (engine, transmis- sion, differential, wheel bearings, etc.) for the first 1,000 miles (1,600
km) of driving.B Maximum load limits
WARNING
Never exceed the maximum load limits explained below. Exceed- ing the maximum load limits could cause personal injury and/or vehicle damage.
8-28
Legacy U.S.A..(ENG.)A2290BE–A
Driving tips
CAUTION
D Adequate size trailer brakes are required when the trailer and its cargo exceed 1,000 lbs (453 kg) total weight. D Before towing a trailer, check the trailer total weight, GVW, GAWs and tongue load. Make sure the load and its distribution in your vehicle and trailer are acceptable.
n Total trailer weight The total trailer weight (trailer weight plus its cargo load) must never exceed the maximum weight shown below.
Model
Conditions
Maximum total trailer weight
MT models When towing a trailer without brakes.
1,000 lbs (453 kg)
When towing a trailer with brakes.
2,000 lbs (906 kg)
AT models When towing a trailer without brakes.
1,000 lbs (453 kg)
When towing a trailer with brakes.
When towing a trailer on a long uphill grade continuously for over 5 miles (8 km) with an outside temperature of 104°F (40°C) or above.
2,000 lbs (906 kg)
1,000 lbs (453 kg)
Total trailer weight
OM-H2781
– CONTINUED –
8-29
Legacy U.S.A..(ENG.)A2290BE–A
n Gross Vehicle Weight (GVW) and Gross Vehicle Weight Rating
(GVWR)
The Gross Vehicle Weight (GVW) must never exceed the Gross Vehicle Weight Rating (GVWR). Gross Vehicle Weight (GVW) is the combined total of the weight of the vehicle, driver, passengers, luggage, trailer hitch, trailer tongue load and any other optional equipment installed on your vehicle. Therefore, the GVW changes depending on the situation. Determine the GVW each time before going on a trip by putting your vehicle and trailer on a vehicle scale. GVWR is shown on the certification label located on the driver’s door of your vehicle.
Gross Vehicle Weight
OM-H2782
HBF019BB
B Gross Axle Weight (GAW) and Gross Axle Weight Rating
(GAWR)
The total weight applied to each axle (GAW) must never exceed the Gross Axle Weight Rating (GAWR). The front and rear GAWs can be adjusted by relocating passengers and luggage inside the vehicle. The front and rear GAWR are also shown on the certification label.
8-30
Legacy U.S.A..(ENG.)A2290BE–A
Gross Axle Weight
Driving tips
OM-H2784
HBF019BB
To check both GVWR and GAWR and to confirm that the total weight and weight distribution are within safe driving limits, you should have your vehicle and trailer weighed at a commercial weighing station. Be sure that all cargo is firmly secured to prevent a change in weight distribution while driving.
n Tongue load
WARNING
If the trailer is loaded with more weight in the back of trailer’s axle than in the front, the load is taken off the rear axle of the tow- ing vehicle. This may cause the rear wheels to skid, especially during braking or when vehicle speed is reduced during corner- ing, resulting in over-steer, spin out and/or jackknifing.
Ensure that the trailer tongue load is from 8 to 11 percent of the total trailer weight and does not exceed the maximum value of 200 lbs (90
kg). The tongue load can be weighed with a bathroom scale as shown in the illustration below. When weighing the tongue load, be sure to posi- tion the towing coupler at the height at which it would be during actual towing, using a jack as shown.– CONTINUED –
8-31
Legacy U.S.A..(ENG.)A2290BE–A
Tongue load
OM-H2785
OM-H2786
The tongue load can be adjusted by proper distribution of the load in the trailer. Never load the trailer with more weight in the back than in the front; approximately 60 percent of the trailer load should be in the front and approximately 40 percent in the rear. Also, distribute the load as evenly as possible on both the left and right sides. Be sure that all cargo is firmly secured to prevent a change in weight distribution while driving.
OM-H2787
8-32
Legacy U.S.A..(ENG.)A2290BE–A
Driving tips
B Trailer hitches
WARNING
Never drill the frame or under-body of your vehicle to install a commercial trailer hitch. If you do, dangerous exhaust gas, water or mud may enter the passenger compartment through the drilled hole. Exhaust gas contains carbon monoxide, a colorless and odorless gas which is dangerous, or even lethal, if inhaled. Also, drilling the frame or under-body of your vehicle could cause dete- rioration of strength of your vehicle and cause corrosion around the drilled hole.
CAUTION
D Do not modify the vehicle exhaust system, brake system, or other systems when installing a hitch or other trailer towing equipment. D Do not use axle-mounted hitches as they can cause damage to the axle housing, wheel bearings, wheels or tires.
Choose a proper hitch for your vehicle and trailer.
B OUTBACK wagon The use of a genuine SUBARU trailer hitch is recommended. A genu- ine SUBARU hitch is available from your SUBARU dealer. If use of a non-genuine hitch is unavoidable, be sure the hitch is suited to your vehicle and trailer. Consult with a professional hitch supplier to assist you in choosing an appropriate hitch for your vehicle. Be sure to follow all of the hitch manufacturer’s instructions for installation and use. Never use a hitch that mounts only to the rear bumper. The bumper is not designed to handle that type of load. For all types of hitches, regularly check that the hitch mounting bolts and nuts are tight.
– CONTINUED –
8-33
Legacy U.S.A..(ENG.)A2290BE–A
B All vehicles except OUTBACK wagon SUBARU does not offer accessory trailer hitches. Consult with a pro- fessional hitch supplier to assist you in choosing an appropriate hitch for your vehicle. Be sure to follow all of the hitch manufacturer’s instructions for installation and use. Never use a hitch that mounts only to the rear bumper. The bumper is not designed to handle that type of load. Regularly check that the hitch mounting bolts and nuts are tight.
B Connecting a trailer n Trailer brakes
WARNING
D Adequate size trailer brakes are required when the trailer and its cargo exceed 1,000 lbs (453 kg) total weight. D Do not directly connect your trailer’s hydraulic brake system to the hydraulic brake system in your vehicle. Direct connection would cause the vehicle’s brake performance to deteriorate and could lead to an accident.
If your trailer’s total weight (trailer weight plus its cargo weight) exceeds 1,000 lbs (453 kg), the trailer is required to be equipped with its own brake system. Electric brakes or surge brakes are recom- mended, and must be installed properly. Check that your trailer’s brakes conform with Federal, state/province and/or other applicable regulations. Your SUBARU’s brake system is not designed to be tapped into the trailer’s hydraulic brake system. Please ask your SUBARU dealer and professional trailer supplier for more information about the trailer’s brake system.
n Trailer safety chains
WARNING
Always use safety chains between your vehicle and the trailer. Towing trailer without safety chains could create a traffic safety hazard if the trailer separates from the hitch due to coupling dam- age or hitch ball damage.
8-34
Legacy U.S.A..(ENG.)A2290BE–A
Driving tips
In case the trailer hitch connector or hitch ball should break or become disconnected, the trailer could get loose and create a traffic safety hazard. For safety, always connect the towing vehicle and trailer with trailer safety chains. Pass the chains crossing each other under the trailer tongue to prevent the trailer from dropping onto the ground in case the trailer tongue should disconnect from the hitch ball. Allow suffi- cient slack in the chains taking tight-turn situations into account; how- ever, be careful not to let them drag on the ground. For more information about the safety chain connection, refer to the instructions for your hitch and trailer.
n Side mirrors After hitching a trailer to your vehicle, check that the standard side mirrors provide a good rearward field of view without significant blind spots. If significant blind spots occur with the vehicle’s standard side mirrors, use towing mirrors that conform with Federal, state/province and/or other applicable regulations.
HB0085
n Trailer lights
CAUTION
Direct splicing or other improper connection of trailer lights may damage your vehicle’s electrical system and cause a malfunction of your vehicle’s lighting system.
– CONTINUED –
8-35
Legacy U.S.A..(ENG.)A2290BE–A
Connection of trailer lights to your vehicle’s electrical system requires modifications to the vehicle’s lighting circuit to increase its capacity and accommodate wiring changes. To ensure the trailer lights are connected properly, please consult your SUBARU dealer. Check for proper operation of the turn signals, the brake lights and parking lights each time you hitch up.
n Tires
WARNING
Never tow a trailer when the temporary spare tire is used. The temporary spare tire is not designed to sustain the towing load. Use of the temporary spare tire when towing can result in failure of the spare tire and/or less stability of the vehicle.
Make sure that all the tires on your vehicle are properly inflated.
OUTBACK: The recommended cold tire pressure under trailer towing conditions is indicated on the tire placard located under the door striker on the driver’s side. Adjust the rear tire pressure to the recommended pressure shown on the tire placard when the tires are cold. Normal pressure should be maintained in the front tires. Other models: It is recommended to inflate the rear tires to 3 psi (20 kPa, 0.2 kg/cm2) above their normal operating pressure when the tires are cold. Normal pressure should be maintained in the front tires.
Trailer tire condition, size, load rating and proper inflation pressure should be in accordance with the trailer manufacturer’s specifications.
In the event your vehicle gets a flat tire when towing a trailer, ask a commercial road service to repair the flat tire.
If you carry a regular size spare tire in your vehicle or trailer as a pre- caution against getting a flat tire, be sure that the spare tire is firmly secured.
8-36
Legacy U.S.A..(ENG.)A2290BE–A
Driving tips
B Trailer towing tips
CAUTION
D Never exceed 45 mph (72 km/h) when towing a trailer in hilly country on hot days. D When towing a trailer, steering, stability, stopping distance and braking performance will be different from normal operation. For safety’s sake, you should employ extra caution when towing a trailer and you should never speed. You should also keep the fol- lowing tips in mind:
n Before starting out on a trip D Check that the vehicle and vehicle-to-hitch mounting are in good condition. If any problems are apparent, do not tow the trailer. D Check that the vehicle sits horizontally with the trailer attached. If the vehicle is tipped sharply up at the front and down at the rear, check the total trailer weight, GVW, GAWs and tongue load again, then confirm that the load and its distribution are acceptable. D Check that the tire pressures are correct. D Check that the vehicle and trailer are connected properly. Confirm that.
– the trailer tongue is connected properly to the hitch ball. – the trailer lights connector is connected properly and trailer’s brake lights illuminate when the vehicle’s brake pedal is pressed, and that the trailer’s turn signal lights flash when the vehicle’s turn signal lever is operated. – the safety chains are connected properly. – all cargo in the trailer is secured safety in position. – the side mirrors provide a good rearward field of view without a significant blind spot.
D Sufficient time should be taken to learn the “feel” of the vehicle/ trailer combination before starting out on a trip. In an area free of traf- fic, practice turning, stopping and backing up.
– CONTINUED –
8-37
Legacy U.S.A..(ENG.)A2290BE–A
n Driving with a trailer D You should allow for considerably more stopping distance when towing a trailer. Avoid sudden braking because it may result in skid- ding or jackknifing and loss of control. D Avoid abrupt starts and sudden accelerations. If your vehicle has a manual transmission, always start out in first gear and release the clutch at moderate engine revolution. D Avoid uneven steering, sharp turns and rapid lane changes. D Slow down before turning. Make a longer than normal turning radius because the trailer wheels will be closer than the vehicle wheels to the inside of the turn. In a tight turn, the trailer could hit your vehicle. D Crosswinds will adversely affect the handling of your vehicle and trailer, causing sway. Crosswinds can be due to weather conditions or the passing of large trucks or buses. If swaying occurs, firmly grip the steering wheel and slow down immediately but gradually. D When passing other vehicles, considerable distance is required because of the added weight and length caused by attaching the trailer to your vehicle. D Backing up with a trailer is difficult and takes practice. When back- ing up with a trailer, never accelerate or steer rapidly. When turning back, grip the bottom of the steering wheel with one hand and turn it to the left for a left turn, and turn it to the right for a right turn.
Left turn
Right turn
OM-H2791
D If the ABS warning light illuminates while the vehicle is in motion, stop towing the trailer and have repairs performed immediately by the
8-38
Legacy U.S.A..(ENG.)A2290BE–A
Driving tips
nearest SUBARU dealer.
n Driving on grades D Before going down a steep hill, slow down and shift into lower gear (if necessary, use 1st gear) in order to utilize the engine braking effect and prevent overheating of your vehicle’s brakes. Do not make sud- den downshifts. D When driving uphill in hot weather, the air conditioner may turn off automatically to protect the engine from overheating. D When driving uphill in hot weather, pay attention to the water tem- perature gauge pointer (for all vehicles) and AT OIL TEMP warning light (for AT vehicles) since the engine and transmission are relatively prone to overheating under these conditions. If the water temperature gauge pointer approaches the OVERHEAT zone or the AT OIL TEMP warning light illuminates, immediately switch off the air conditioner and stop the vehicle at the nearest safe place. Refer to the “Engine overheat” section in chapter 9, and “Warning and indicator lights” section in chapter 3. D If your vehicle has a automatic transmission, avoid using the accel- erator pedal to stay stationary on an uphill slope instead of using the parking brake or foot brake. That may cause the transmission fluid to overheat. Also, if your vehicle is equipped with an automatic transmis- sion, avoid driving with the gear selector lever in “D” when towing a heavy trailer to prevent fluid overheating.
n Parking on a grade Always block the wheels under both vehicle and trailer when parking. Apply the parking brake firmly. You should not park on a hill or slope. But if parking on a hill or slope cannot be avoided, you should take the following steps: 1. Apply the brakes and hold the pedal down. 2. Have someone place wheel blocks under both the vehicle and trailer wheels. 3. When the wheel blocks are in place, release the regular brakes slowly until the blocks absorb the load. 4. Apply the regular brakes and then apply the parking brake; slowly release the regular brakes.
– CONTINUED –
8-39
Legacy U.S.A..(ENG.)A2290BE–A
5. Shift into 1st or reverse gear (manual transmission) or “P” (auto- matic transmission) and shut off the engine.
8-40
Legacy U.S.A..(ENG.)A2290BE–A
In case of emergency
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
If you park your vehicle in an emergency Temporary spare tire Flat tires Jump starting Engine overheating Towing Moonroof — if the moonroof cannot be closed Maintenance tools
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jack and jack handle
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
9-2
9-3
9-4
9-11
9-14
9-15
9-25
9-26
9-27Legacy U.S.A..(ENG.)A2290BE–A
If you park your vehicle in an emergency
HB8002BA
The hazard warning flasher should be used in day or night to warn other drivers when you have to park your vehicle under emergency conditions. Avoid stopping on the road. It is best to safely pull off the road if a prob- lem occurs.
The hazard warning flasher can be activated regardless of the ignition switch position. Turn on the hazard warning by pushing the hazard warning flasher switch. Turn it off by pushing the switch again.
NOTE When the hazard warning flasher is on, the turn signals do not work.
9-2
Legacy U.S.A..(ENG.)A2290BE–A
Temporary spare tire
In case of emergency
WARNING
Never tow a trailer when the temporary spare tire is used. The temporary spare tire is not designed to sustain the towing load. Use of the temporary spare tire when towing can result in failure of the spare tire and/or less stability of the vehicle and may lead to an accident.
CAUTION
Never use any temporary spare tire other than the original. Using other sizes may result in severe mechanical damage to the drive train of your vehicle.
The temporary spare tire is smaller and lighter than a conventional tire and is designed for emergency use only. Remove the temporary spare tire and re-install the conventional tire as soon as possible because the spare tire is designed only for temporary use.
Check the inflation pressure of the temporary spare tire periodically to keep the tire ready for use. The correct pressure is 60 psi (420 kPa, 4.2
kg/cm2).When using the temporary spare tire, note the following:
D Do not exceed 50 mph (80 km/h). D Do not put a tire chain on the temporary spare tire. Because of the smaller tire size, a tire chain will not fit properly. D Do not use two or more temporary spare tires at the same time. D Do not drive over obstacles. This tire has a smaller diameter, so road clearance is reduced. D When the wear indicator appears on the tread, replace the tire.
– CONTINUED –
9-3
Legacy U.S.A..(ENG.)A2290BE–A
Indicator location mark
Tread wear indicator bar
HG0106
HB8003BB
NOTE [Automatic transmission vehicle not equipped with VDC (Vehicle Dy- namics Control)] Before driving your vehicle with the temporary spare tire, put a spare fuse inside the FWD connector located in the engine compartment and confirm that the Front-wheel drive warning light comes on. The all wheel drive capability of the vehicle has now been deactivated. After re-installing the conventional tire, remove the spare fuse from the FWD connector in order to reactivate all wheel drive.
Flat tires
WARNING
D Do not jack up the vehicle on an incline or a loose road sur- face. The jack can come out of the jacking point or sink into the ground and this can result in a severe accident. D Use only the jack provided with your vehicle. The jack sup- plied with the vehicle is designed only for changing a tire. Never get under the vehicle while supporting the vehicle with this jack. D Always turn the engine off before raising the flat tire off the ground using the jack. Never swing or push the vehicle sup- ported with the jack. The jack can come out of the jacking point due to a jolt and this can result in a severe accident.
9-4
Legacy U.S.A..(ENG.)A2290BE–A
In case of emergency
D Do not use oil or grease on the wheel studs or nuts when the spare tire is installed. This could cause the nuts to become loose and lead to an accident. D Never place a tire or tire changing tools in the passenger compartment after changing wheels. In a sudden stop or colli- sions, loose equipment could strike occupants and cause injury. Store the tire and all tools in the proper place.
If you have a flat tire while driving, never brake suddenly; keep driving straight ahead while gradually reducing speed. Then slowly pull off the road to a safe place.
1. Park on a hard, level surface, whenever possible, then stop the en- gine. 2. Set the parking brake securely and shift a manual transmission ve- hicle in reverse or an automatic transmission vehicle in the “P” (Park) position. 3. Turn on the hazard warning flasher and have everyone get out of the vehicle. 4. Put wheel blocks at the front and rear of the tire diagonally opposite the flat tire.
Jacking position
Wheel blocks
OM-H2259
– CONTINUED –
9-5
Legacy U.S.A..(ENG.)A2290BE–A
5. Take out the spare tire, jack, and wheel nut wrench.
Jack
Jack handle
Spare tire
HBF015CB
HB8004BD
Temporary spare tire
HB9003BB
HB6008BC
HS0252
The spare tire is stored under the floor of the trunk or cargo area. To remove the spare tire, proceed as follows: Sedan: Remove the floor cover from the trunk. Remove the storage tray. Turn the attaching bolt counterclockwise, then take the spare tire out. Station wagon: Open the lid and hang the hook provided on the under-
9-6
Legacy U.S.A..(ENG.)A2290BE–A
In case of emergency
side of the lid on the rear edge of the roof to keep the lid open. Remove the storage tray. Turn the attaching bolt counterclockwise, then take spare tire out.
If the spare tire provided in your vehicle is a temporary spare tire, care- fully read the section “Temporary spare tire” in this chapter and strictly follow the instructions.
HB9001BB
HB7008CD
The jack is stored on the left side of the trunk or cargo area.
To take out the jack: Remove the cover, turn the jackscrew counterclockwise to loosen it, then remove the jack.
The jack handle is stored under the spare tire cover.
NOTE Make sure the jack is well lubricated before using it.
– CONTINUED –
9-7
Legacy U.S.A..(ENG.)A2290BE–A
6. (If your vehicle has wheel covers) Insert the wheel nut wrench into the notch provided in the wheel cover, and pry it off.
HB9032BA
OM-H0376
7. Loosen the wheel nuts using the wheel nut wrench but do not remove the nuts. 8. Place the jack under the side sill at the front or rear jack-up point clos- est to the flat tire.
OM-H2262
HB9012BB
Turn the jackscrew by hand until the jack head engages firmly into the jack-up point. If your vehicle is equipped with side sill skirts, jack-up points are pointed to by arrow marks on the underside of the side sill skirt. Place the jack under the front or rear jack-up point closest to flat tire.
9-8
Legacy U.S.A..(ENG.)A2290BE–A
9. Insert the jack handle into the jackscrew, and turn the handle until the tire clears the ground. Do not raise the vehicle higher than necessary.
In case of emergency
OM-H2263
10. Remove the wheel nuts and the flat tire. 11. Before putting the spare tire on, clean the mounting surface of the wheel and hub with a cloth.
OM-H0172
HG0104
12. Put on the spare tire. Replace the wheel nuts. Tighten them by hand. 13. Turn the jack handle counterclockwise to lower the vehicle.
– CONTINUED –
9-9
Legacy U.S.A..(ENG.)A2290BE–A
14. Use the wheel nut wrench to securely tighten the wheel nuts to the specified torque, following the tightening order in the illustration.
OM-H0377
The torque for tightening the nuts is 58 to 72 ft-lb (78 to 98 N-m, 8 to 10
kg-m). This torque is equivalent to applying about 88 to 110 lbs (40 to 50
kg) at the top of the wheel nut wrench. Never use your foot on the wheel nut wrench or a pipe extension on the wrench because you may exceed the specified torque. Have the wheel nut torque checked at the nearest automotive service facility.15. Store the flat tire in the spare tire compartment.
Flat tire
Attaching bolt
Spacer
HS0153
When storing a conventional tire, put the spacer upside down and tight- en the attaching bolt firmly. Also store the jack and wheel nut wrench in their storage locations.
9-10
Legacy U.S.A..(ENG.)A2290BE–A
Jump starting
In case of emergency
WARNING
D Battery fluid is SULFURIC ACID. Do not let it come in contact with the eyes, skin, clothing or the vehicle. If battery fluid gets on you, thoroughly flush the exposed area with water immediately. Get medical help if the fluid has entered your eyes. If battery fluid is accidentally swallowed, immediately drink a large amount of milk or water, and obtain immediate medical help. Keep everyone including children away from the battery. D The gas generated by a battery explodes if a flame or spark is brought near it. Do not smoke or light a match while jump start- ing. D Never attempt jump starting if the discharged battery is frozen. It could cause the battery to burst or explode. D Whenever working on or around a battery, always wear suit- able eye protectors, and remove metal objects such as rings, bands or other metal jewelry. D Be sure the jumper cables and clamps on them do not have loose or missing insulation. Do not jump start unless cables in suitable condition are avail- able. D A running engine can be dangerous. Keep your fingers, hands, clothing, hair and tools away from the cooling fan, belts and any other moving engine parts. Removing rings, watches and ties is advisable.
When your vehicle does not start due to a run down (discharged) bat- tery, the vehicle may be jump started by connecting your battery to another battery (called the booster battery) with jumper cables.
Jump starting is dangerous if it done incorrectly. If you are unsure about the proper procedure for jump starting, consult a competent mechanic.
– CONTINUED –
9-11
Legacy U.S.A..(ENG.)A2290BE–A
B How to jump start 1. Make sure the booster battery is 12 volts and the negative terminal is grounded. 2. If the booster battery is in another vehicle, do not let the two ve- hicles touch. 3. Turn off all unnecessary lights and accessories. 4. Connect the jumper cables exactly in the sequence illustrated.
HB8007BC
9-12
Legacy U.S.A..(ENG.)A2290BE–A
In case of emergency
HB9031BB
1 Connect one jumper cable to the positive (+) terminal on the discharged battery. 2 Connect the other end of the jumper cable to the positive (+) terminal of the booster battery. 3 Connect one end of the other cable to the negative (–) terminal of the booster battery. 4 Connect the other end of the cable.
2.5 liter models: To the engine lifting bracket. 3.0 liter models: To the strut mounting nut.
Make sure that the cables are not near any moving parts and that the cable clamps are not in contact with any other metal.
5. Start the engine of the vehicle with the booster battery and run it at moderate speed. Then start the engine of the vehicle that has the dis- charged battery. 6. When finished, carefully disconnect the cables in exactly the re- verse order.
– CONTINUED –
9-13
Legacy U.S.A..(ENG.)A2290BE–A
Engine overheating
WARNING
Never attempt to remove the radiator cap until the engine has been shut off and has fully cooled down. When the engine is hot, the coolant is under pressure. Removing the cap while the engine is still hot could release a spray of boiling hot coolant, which could burn you very seriously.
If the engine overheats, safely pull off the road and stop the vehicle in a safe place.
B If steam is coming from the engine compartment Turn the engine off and get everyone away from the vehicle until it cools down.
B If no steam is coming from the engine compartment 1. Keep the engine running at idling speed. 2. Open the hood to ventilate the engine compartment. Confirm that the cooling fan is turning. If the fan is not turning, im- mediately turn the engine off and contact your authorized dealer for repair. 3. After the engine coolant temperature has dropped, turn off the en- gine. If the temperature gauge stays at the overheated zone, turn the en- gine off. 4. After the engine has fully cooled down, check the coolant level in the reserve tank. If the coolant level is below the “MIN” mark, add coolant up to the “MAX” mark. 5. If there is no coolant in the reserve tank, add coolant to the reserve tank. Then remove the radiator cap and fill the radiator with coolant.
If you remove the radiator cap from a hot radiator, first wrap a thick cloth around the radiator cap, then turn the cap counterclockwise slowly without pressing down until it stops. Release the pressure from
9-14
Legacy U.S.A..(ENG.)A2290BE–A
the radiator. After the pressure has been fully released, remove the cap by pressing down and turning it.
In case of emergency
Towing
WARNING
Never tow AWD vehicles (both AT and MT) with the front wheels raised off the ground while the rear wheels are on the ground, or with the rear wheels raised off the ground while the front wheels are on the ground. This will cause the vehicle to spin away due to the operation or deterioration of the center differential.
99
HG9013BA
If towing is necessary, it is best done by your SUBARU dealer or a com- mercial towing service. Observe the following procedures for safety.
B Towing and tie-down hooks
CAUTION
D Use only specified towing hooks and tie-down hooks. Never use suspension parts or other body parts for towing or tie-down purposes. D Never use the tie-down hook closest to the muffler under the vehicle for towing purposes. D Do not apply excessive lateral load to the towing hooks.
– CONTINUED –
9-15
Legacy U.S.A..(ENG.)A2290BE–A
HB9004BB
HB9005BB
Towing and tie-down hook HB8012BB
HB8013BB
9-16
Legacy U.S.A..(ENG.)A2290BE–A
In case of emergency
HB9010BB
The towing hooks should be used only in an emergency (e.g., to free a stuck vehicle from mud, sand or snow).
The front towing hook is located on the inside of the towing hook cov- er below the right-hand headlight.
n Towing hook cover removal procedure For except OUTBACK models:
1. Push at the notched portion A, and pull the towing hook cover to- ward you.
HB9013BB
– CONTINUED –
9-17
Legacy U.S.A..(ENG.)A2290BE–A
HB9014BB
2. Insert your fingers under the raised portion B. Then, pull it toward you so that the towing hook cover may swing open. Remove the cov- er. For OUTBACK models:
HB9017BB
HB9018BA
1. Pull the towing hook cover toward you while pushing up the portion A. The portion B will be raised.
9-18
Legacy U.S.A..(ENG.)A2290BE–A
In case of emergency
HB9019BB
HB9020BA
HB9021BB
HB9022BA
2. Pull the portion B toward you with your left hand. Simultaneously pull the portion C toward you while pushing the portion C with your right hand.
HB9023BB
HB9024BA
3. Push the portion D. Pull out the towing hook cover to remove it.
– CONTINUED –
9-19
Legacy U.S.A..(ENG.)A2290BE–A
n Towing hook cover installation procedure For except OUTBACK models:
HB9015BA
HB9016BA
1. Insert the towing hook cover into the clearance between the fog light (or bumper trim cover) and the bumper body.
HB9013CB
2. Push the towing hook cover in accordance with the pushing order given in the illustration.
9-20
Legacy U.S.A..(ENG.)A2290BE–A
For OUTBACK models:
In case of emergency
1. Insert the guide E into the hole F.
HB9025BA
HB9026BB
HB9027BB
2. Fit the flange G in the slit H from the left end. While holding the towing hook cover at the portion G, push at the portion I.
– CONTINUED –
9-21
Legacy U.S.A..(ENG.)A2290BE–A
HB9028BB
HB9029BB
3. Push at the portion J. Check that the tab of the portion K is fitted in the bumper as shown in the illustration.
4. Push the portion L.
HB9030BB
9-22
Legacy U.S.A..(ENG.)A2290BE–A
B Using a flat-bed truck
In case of emergency
HB8008AA
This is the best way to transport your vehicle. Use the following proce- dures to ensure safe transportation. 1. Shift the selector lever into the “P” position for automatic transmis- sion vehicles or “1st” for manual transmission vehicles. 2. Pull up the parking brake lever firmly. 3. Secure the vehicle onto the carrier properly with safety chains. Each safety chain should be equally tightened and care must be tak- en not to pull the chains so tightly that the suspension bottoms out.
B Towing with all wheels on the ground
WARNING
D Never turn the ignition switch to the “LOCK” position while the vehicle is being towed because the steering wheel and the direc- tion of the wheels will be locked. D Remember that the brake booster and power steering do not function when the engine is not running. Because the engine is turned off, it will take greater effort to operate the brake pedal and steering wheel.
– CONTINUED –
9-23
Legacy U.S.A..(ENG.)A2290BE–A
CAUTION
D If transmission failure occurs, transport your vehicle on a flat- bed truck. D Do not run the engine while being towed in this method. Trans- mission damage could result if the vehicle is towed with the engine running. D For vehicles with automatic transmission, the traveling speed must be limited to less than 20 mph (30 km/h) and the traveling distance to less than 31 miles (50 km). For greater speeds and distances, transport your vehicle on a flat-bed truck.
HB8010AA
1. Check the transmission and differential oil levels and add oil to bring it to the upper level if necessary. 2. Release the parking brake and put the transmission in neutral. 3. The ignition switch should be in the “ACC” position while the ve- hicle is being towed. 4. Take up slack in the towline slowly to prevent damage to the ve- hicle.
9-24
Legacy U.S.A..(ENG.)A2290BE–A
In case of emergency
Moonroof — if the moonroof cannot be closed
If the moonroof cannot be closed with the moonroof switch, you can close the moonroof manually.
B Sedan 1. Take out the hex-headed wrench from the glove compartment and screwdriver from the tool bag.
HB9006BA
HB9007BB
2. Remove the spot light lens by prying the edge of the lens with a regular screwdriver, then remove the switch body retaining screws and take off the moonroof switch.
HB9008BA
3. Insert the wrench in the end of the motor shaft. D To lower the moonroof, turn the wrench clockwise. D To close the moonroof, turn the wrench counterclockwise. Have your vehicle checked by an authorized SUBARU dealer.
– CONTINUED –
9-25
Legacy U.S.A..(ENG.)A2290BE–A
B Station wagon 1. Take out the hex-headed wrench from the glove compartment and screwdriver from the tool bag.
HB9033BA
HB9034BB
2. Remove the plug on the roof trim by inserting the end of the regular screwdriver between the roof and plug and prying it off. 3. Insert the wrench in the end of the motor shaft. To close the moonroof, turn the wrench clockwise.
Have your vehicle checked or repaired by an authorized SUBARU dealer.
Maintenance tools
Your vehicle is equipped with the following maintenance tools:
HB9011AA
9-26
Legacy U.S.A..(ENG.)A2290BE–A
In case of emergency
Screwdriver Wheel nut wrench Hex-headed wrench (for vehicles with moonroof)
J Jack and jack handle
Jack
Jack handle
Spare tire
HBF015CB
HB9001BA
HB8004BD
HB7008CA
The jack is stored on the left side of the trunk or cargo area.
To take out the jack, turn the jackscrew counterclockwise to loosen it, then remove the jack.
The jack handle is stored under the spare tire cover.
For how to use the jack, refer to “Flat tires”.
– CONTINUED –
9-27
Legacy U.S.A..(ENG.)A2290BE–A
Appearance care
Exterior care
Washing Waxing and polishing Cleaning aluminum wheels Cleaning fog light lens (for OUTBACK)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Corrosion protection Cleaning the interior
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-2
10-2
10-3
10-4
10-4
10-5
10-610
Legacy U.S.A..(ENG.)A2290BE–A
Exterior care
J Washing
CAUTION
D When washing the vehicle, the brakes may get wet. As a result, the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes. D Do not wash the engine compartment and areas adjacent to it. If water enters the engine air intake, electrical parts or the power steering fluid reservoir, it will cause engine trouble or faulty power steering respectively.
The best way to preserve your vehicle’s beauty is frequent washing. Wash the vehicle at least once a month to avoid contamination by road grime.
Wash dirt off with a wet sponge and plenty of lukewarm or cold water. Do not wash the vehicle with hot water and in direct sunlight.
Salt, chemicals, insects, tar, soot and bird droppings should be washed off by using a light detergent, as required. If you use a light detergent, make certain that it is a neutral detergent. Do not use strong soap or chemical detergents. All cleaning agents should be promptly flushed from the surface and not allowed to dry there. Rinse the vehicle thor- oughly with plenty of lukewarm water. Wipe the remaining water off with a chamois or soft cloth.
NOTE When having your vehicle washed in an automatic car wash, make sure beforehand that the car wash is of suitable type. If the vehicle is equipped with a rear/roof spoiler, it may be damaged by car wash brushes or other equipment.
10-2
Legacy U.S.A..(ENG.)A2290BE–A
Appearance care
B Washing the underbody Chemicals, salts and gravel used for deicing road surfaces are ex- tremely corrosive, accelerating the corrosion of underbody compo- nents, such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders, and suspension. Thoroughly flush the underbody and inside of the fenders with luke- warm or cold water at frequent intervals to reduce the harmful effects of such agents.
B Using a warm water washer D Keep a good distance of 12 in (30 cm) or more between the wash- er nozzle and the vehicle. D Do not wash the same area continuously. D If a stain will not come out easily, wash by hand. Some warm water washers are of the high temperature, high pressure type, and they can damage or deform the resin parts such as mouldings, or cause water to leak into the vehicle.
J Waxing and polishing Always wash and dry the vehicle before waxing and polishing. Use a good quality polish and wax and apply them according to the manufacturer’s instructions. Wax or polish when the painted surface is cool.
Be sure to polish and wax the chrome trim, as well as the painted sur- faces. Loss of wax on a painted surface leads to loss of the original lus- ter and also quickens the deterioration of the surface. It is recommended that a coat of wax be applied at least once a month, or whenever the surface no longer repels water.
If the appearance of the paint has diminished to the point where the lus- ter or tone cannot be restored, lightly polish the surface with a fine- grained compound. Never polish just the affected area, but include the surrounding area as well. Always polish in only one direction. A No. 2000
grain compound is recommended. Never use a coarse-grained com- pound. Coarser grained compounds have a smaller grain-size number and could damage the paint. After polishing with a compound, coat with– CONTINUED –
10-3
10
Legacy U.S.A..(ENG.)A2290BE–A
wax to restore the original luster. Frequent polishing with a compound or an incorrect polishing technique will result in removing the paint layer and exposing the undercoat. When in doubt, it is always best to contact your SUBARU dealer or an auto paint specialist.
J Cleaning aluminum wheels D Promptly wipe the aluminum wheels clean of any kind of grime or agent. If dirt is left on too long, it may be difficult to clean off. D Do not use soap containing grit to clean the wheels. Be sure to use a neutral cleaning agent, and later rinse thoroughly with water. Do not clean the wheels with a stiff brush or expose them to a high-speed wash- ing device. D Clean the vehicle (including the aluminum wheels) with water as soon as possible when it has been splashed with sea water, exposed to sea breezes, or driven on roads treated with salt or other agents.
J Cleaning fog light lens (for OUTBACK)
HBA017BB
1. Stop the vehicle in a safe place. 2. Stop the engine and turn off the fog lights. 3. Check that the fog lights are not hot. Then, grasp the protector and turn it approximately 10° counter-clockwise. 4. Pull the protector off the fog light. 5. Wash the lens with water. 6. Apply the protector to the lens at an angle of approximately 10° from
10-4
Legacy U.S.A..(ENG.)A2290BE–A
Appearance care
the fog light’s horizontal center line. Then, turn the protector clockwise until it stops. Finally, check that the protector’s horizontal bars are parallel with the fog light’s horizontal center line.
Corrosion protection
Your SUBARU has been designed and built to resist corrosion. Special materials and protective finishes have been used on most parts of the vehicle to help maintain fine appearance, strength, and reliable opera- tion.
B Most common causes of corrosion The most common causes of corrosion are: 1. The accumulation of moisture retaining dirt and debris in body panel sections, cavities, and other areas. 2. Damage to paint and other protective coatings caused by gravel and stone chips or minor accidents.
Corrosion is accelerated on the vehicle when: 1. It is exposed to road salt or dust control chemicals, or used in coastal areas where there is more salt in the air, or in areas where there is considerable industrial pollution. 2. It is driven in areas of high humidity, especially when temperatures range just above freezing. 3. Dampness in certain parts of the vehicle remains for a long time, even though other parts of the vehicle may be dry. 4. High temperatures will cause corrosion to parts of the vehicle which cannot dry quickly due to lack of proper ventilation.
B To help prevent corrosion Wash the vehicle frequently. If you drive on salted roads in the winter or if you live in a coastal area, you should flush the underbody with fresh water frequently.
After the winter has ended, it is recommended that the underbody be given a very thorough washing.
– CONTINUED –
10-5
10
Legacy U.S.A..(ENG.)A2290BE–A
Before the beginning of winter, check the condition of underbody components, such as the exhaust system, fuel and brake lines, brake cables, suspension, steering system, floor pan, and fenders. If any of them are found to be rusted, they should be given an appropriate rust prevention treatment or should be replaced. Contact your SUBARU dealer to perform this kind of maintenance and treatment if you need assistance.
Repair chips and scratches in the paint as soon as you find them.
Check the interior of the vehicle for water and dirt accumulation under the floor mats because that could cause corrosion. Occasionally check under the mats to make sure the area is dry.
Keep your garage dry. Do not park your vehicle in a damp, poorly ventilated garage. In such a garage, corrosion can be caused by dampness. If you wash the vehicle in the garage or put the vehicle into the garage when wet or covered with snow, that can cause dampness.
If your vehicle is operated in cold weather and/or in areas where road salts and other corrosive materials are used, the door hinges and locks, trunk lid lock, and hood latch should be inspected and lubri- cated periodically.
Cleaning the interior
Use a vacuum cleaner to get rid of the dust and dirt. Wipe the vinyl areas with a clean, damp cloth.
B Seat fabric Remove loose dirt, dust or debris with a vacuum cleaner. If the dirt is caked on the fabric or hard to remove with a vacuum cleaner, use a soft blush then vacuum it. Wipe the fabric surface with a tightly wrung cloth and dry the seat fabric thoroughly. If the fabric is still dirty, wipe using a solution of mild soap and lukewarm water then dry thoroughly.
If the stain does not come out, try a commercially-available fabric
10-6
Legacy U.S.A..(ENG.)A2290BE–A
Appearance care
cleaner. Use the cleaner on a hidden place and make sure it does not affect the fabric adversely. Use the cleaner according to its instruc- tions.
B Leather seat materials The leather used by SUBARU is a high quality natural product which will retain its distinctive appearance and feel for many years with proper care. Allowing dust or road dirt to build up on the surface can cause the material to become brittle and to wear prematurely. Regular cleaning with a soft, moist, natural fiber cloth should be performed monthly, taking care not to soak the leather or allow water to penetrate the stitched seams. A mild detergent suitable for cleaning woolen fabrics may be used to remove difficult dirt spots, rubbing with a soft, dry cloth afterwards to restore the luster. If your SUBARU is to be parked for a long time in bright sunlight, it is recommended that the seats and headrests be covered, or the windows shaded, to prevent fading or shrinkage. Minor surface blemishes or bald patches may be treated with a com- mercial leather spray lacquer. You will discover that each leather seat section will develop soft folds or wrinkles, which is characteristic of genuine leather.
B Synthetic leather upholstery The synthetic leather material used on the SUBARU may be cleaned using mild soap or detergent and water, after first vacuuming or brushing away loose dirt. Allow the soap to soak in for a few minutes and wipe off with a clean, damp cloth. Commercial foam-type clean- ers suitable for synthetic leather materials may be used when neces- sary.
NOTE Strong cleaning agents such as solvents, paint thinners, window cleaner or gasoline must never be used on leather or synthetic interior materials.
– CONTINUED –
10-7
10
Legacy U.S.A..(ENG.)A2290BE–A
Maintenance and service
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance schedule Maintenance precautions Engine hood Engine compartment overview Engine oil Cooling system Engine coolant
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air cleaner element Spark plugs Drive belts Manual transmission oil Automatic transmission fluid Front differential gear oil (AT vehicles) Rear differential gear oil Power steering fluid Brake fluid Clutch fluid (MT vehicles) Brake booster Brake pedal Clutch pedal (Manual transmission vehicles) Replacement of brake pad and lining Parking brake stroke Tires and wheels
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Types of tires Tire inspection Tire pressures and wear Wheel balance Wear indicators Tire rotation Tire replacement Wheel replacement Wheel covers
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aluminum wheels (If equipped) Windshield washer fluid Replacement of windshield wiper blades
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-3
11-3
11-5
11-7
11-9
11-14
11-15
11-18
11-20
11-22
11-23
11-24
11-26
11-27
11-29
11-30
11-32
11-33
11-34
11-35
11-36
11-37
11-38
11-38
11-39
11-39
11-42
11-43
11-44
11-44
11-45
11-46
11-47
11-47
11-4811
Legacy U.S.A..(ENG.)A2290BE–A
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Fuses Main fuse Installation of accessories Replacing bulbs
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight Front fog light (if equipped) Front turn signal light, parking light and marker light Rear combination lights License plate light Spot light, dome light, luggage compartment light
and door step light
Trunk light High mount stop light
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-51
11-52
11-54
11-54
11-55
11-57
11-59
11-59
11-61
11-6411-65
11-66
11-6711-2
Legacy U.S.A..(ENG.)A2290BE–A
Maintenance and service
Maintenance schedule
The scheduled maintenance items required to be serviced at regular in- tervals are shown in the “Warranty and Maintenance Booklet”.
For details of your maintenance schedule, read the separate “Warranty and Maintenance Booklet”.
Maintenance precautions
When maintenance and service are required, it is recommended that all work be done by an authorized SUBARU dealer.
If you perform maintenance and service by yourself, you should familiar- ize yourself with the information provided in this section on general main- tenance and service for your SUBARU.
Incorrect or incomplete service could cause improper or unsafe vehicle operation. Any problems caused by improper maintenance and service performed by you are not eligible for warranty coverage.
WARNING
D Testing of an All-Wheel Drive vehicle must NEVER be per- formed on a single two-wheel dynamometer or similar apparatus. Attempting to do so will result in transmission damage and in uncontrolled vehicle movement and may cause an accident or injuries to persons nearby. D Always select a safe area when performing maintenance on your vehicle. D Always be very careful to avoid injury when working on the ve- hicle. Remember that some of the materials in the vehicle may be hazardous if improperly used or handled, for example, battery acid. D Your vehicle should only be serviced by persons fully compe- tent to do so. Serious personal injury may result to persons not experienced in servicing vehicles.
– CONTINUED –
11-3
11
Legacy U.S.A..(ENG.)A2290BE–A
D Always use the proper tools and make certain that they are well maintained. D Never get under the vehicle supported only by a jack. Always use a safety stands to support the vehicle. D Never keep the engine running in a poorly ventilated area, such as a garage or other closed areas. D Do not smoke or allow open flames around the fuel or battery. This will cause a fire. D Because the fuel system is under pressure, replacement of the fuel filter should be performed only by your SUBARU dealer. D Wear adequate eye protection to guard against getting oil or fluids in your eyes. If something does get in your eyes, thorough- ly wash them out with clean water. D Do not tamper with the wiring of the SRS airbag system or seatbelt pretensioner system, or attempt to take its connectors apart, as that may activate the system or it can render it inopera- tive. The wiring and connectors of these systems are yellow for easy identification. NEVER use a circuit tester for these wiring. If your SRS airbag or seatbelt pretensioner needs service, con- sult your nearest SUBARU dealer.
J Before checking or servicing in the engine compart-
ment
D Always stop the engine and set the parking brake firmly to pre- vent the vehicle from moving. D Always let the engine cool down. Engine parts become very hot when the engine is running and remain hot for some time af- ter the engine is stopped. D Do not spill engine oil, engine coolant, brake fluid or any other fluid on hot engine components. This may cause a fire. D Always remove the key from the ignition switch. When the ignition switch is in the “ON” position, the cooling fan may oper- ate suddenly even when the engine is stopped.
11-4
Legacy U.S.A..(ENG.)A2290BE–A
Maintenance and service
J When you do checking or servicing in the engine
compartment while the engine is running
A running engine can be dangerous. Keep your fingers, hands, clothing, hair and tools away from the cooling fan, belts and any other moving engine parts. Removing rings, watches and ties is advisable.
Engine hood
WARNING
Always check that the hood is properly locked before you start driving. If it is not, it might fly open while the vehicle is moving and block your view, which may cause an accident and serious bodily injury.
HBB001BA
HBB002BA
11
– CONTINUED –
11-5
Legacy U.S.A..(ENG.)A2290BE–A
HBB003BA
To open the hood: 1. Pull the hood release knob under the instrument panel. 2. Release the secondary hood release located under the front grille by moving the lever toward the left. Lift up the hood, release the hood prop from its retainer and put the end of the hood prop into the slot in the hood.
To close the hood: 1. Lift the hood slightly and remove the hood prop from the slot in the hood and return the prop to its retainer. 2. Lower the hood until it approaches about 6 in. (15 cm) from the closed position and let it drop. 3. After closing the hood, be sure the hood is securely locked.
If this does not close the hood, release it from a slightly higher position. Do not push the hood forcibly to close it. It could deform the metal.
11-6
Legacy U.S.A..(ENG.)A2290BE–A
Maintenance and service
Engine compartment overview
B 2.5 liter models
1 Manual transmission oil level gauge (MT) (page 11-23) or Differential gear oil level gauge (AT) (page 11-26)
2 Air cleaner element
(page 11-18)
3 Clutch fluid reservoir
(page 11-32)
4 Automatic
transmission level gauge (page 11-24)
5 Brake fluid reservoir
(page 11-30)
6 Fuel filter
HBB036BB
7 Windshield washer tank
(page 11-47)
8 Fuse box (page 11-52) 9 Battery (page 11-51) Q Engine oil filler cap
(page 11-9)
W Engine coolant reservoir
(page 11-15)
11
fluid
E Radiator cap (page 11-15) R Engine oil level gauge
(page 11-9)
T Power steering fluid reservoir
(page 11-29)
– CONTINUED –
11-7
Legacy U.S.A..(ENG.)A2290BE–A
B 3.0 liter models
1 Air cleaner element
(page 11-18)
2 Differential gear oil level gauge
(AT) (page 11-26)
3 Automatic
transmission level gauge (page 11-24)
4 Brake fluid reservoir
(page 11-30)
5 Fuel filter 6 Windshield washer tank
(page 11-47)
11-8
HBB058BB
7 Fuse box (page 11-52) 8 Battery (page 11-51) 9 Engine oil filler cap
(page 11-9)
fluid
Q Engine coolant reservoir
(page 11-15)
W Engine oil level gauge
(page 11-9)
E Radiator cap (page 11-15) R Power steering fluid reservoir
(page 11-29)
Legacy U.S.A..(ENG.)A2290BE–A
Maintenance and service
Engine oil
B Checking the oil level Check the engine oil level at each fuel stop.
HBB004BA
HBB061BD
1. Park the vehicle on a level surface and stop the engine. 2. Pull out the dipstick, wipe it clean, and insert it again. 3. Be sure the dipstick is correctly inserted until it stops with the graphic symbol on its top appearing as shown in the illustra- tion. 4. Pull out the dipstick again and check the oil level on it. If it is below the lower level, add oil to bring the level up to the upper level.
CAUTION
Use only engine oil with the recommended grade and viscosity.
If you check the oil level just after stopping the engine, wait a few min- utes for the oil to drain back into the oil pan before checking the level. To prevent overfilling the engine oil, do not add any additional oil above the upper level when the engine is cold.
In 2.5-liter-engine models, the dipstick has a notch above the upper level. Just after driving or while the engine is warm, the engine oil level reading may be in a range between the upper level and the notch mark. This is caused by thermal expansion of the engine oil.
– CONTINUED –
11-9
11
Legacy U.S.A..(ENG.)A2290BE–A
B Changing the oil and oil filter Change the oil and oil filter according to the maintenance schedule in the “Warranty and Maintenance Booklet”. The engine oil and oil filter must be changed more frequently than listed in the maintenance schedule when driving on dusty roads, when short trips are frequently made, or when driving in extremely cold whether.
1. Warm up the engine by letting the engine idle for about 10 minutes to ease draining the engine oil. 2. Park the vehicle on a level surface and stop the engine. 3. Remove the oil filler cap.
HBB005BB
4. Drain out the engine oil by removing the drain plug while the en- gine is still warm. The used oil should be drained into an appropriate container and disposed of properly.
WARNING
Be careful not to burn yourself with hot engine oil.
5. Wipe the seating surface of the drain plug with a clean cloth and tighten it securely with a new sealing washer after the oil has com- pletely drained out.
11-10
Legacy U.S.A..(ENG.)A2290BE–A
Maintenance and service
HBB051BB
HBB054BA
HBB055BA
6. Remove three clips at the front of the cover under the oil filter. 7. Slide the cover toward the vehicle front to remove it. 8. Remove the oil filter with an oil filter wrench. 9. Before installing a new oil filter, apply a thin coat of engine oil to the seal. 10. Clean the rubber seal seating area of the lower crank case and install the oil filter by hand turning. Be careful not to twist or damage the seal. 11. Tighten it approximately two-thirds of a turn after the seal makes contact with the lower crank case.
CAUTION
Never over tighten the oil filter because that can result in an oil leak.
– CONTINUED –
11-11
11
Legacy U.S.A..(ENG.)A2290BE–A
12. Reinstall the cover under the oil filter. 13. Pour the specified amount of engine oil through the filler neck.
Oil capacity:
2.5 liter models: 4.2 US qt (4.0 liters, 3.5 Imp qt) 3.0 liter models: 6.1 US qt (5.8 liters, 5.1 Imp qt)
14. Start the engine and make sure that no oil leaks appear around the filter’s rubber seal. 15. Run the engine until it reaches the normal operating temperature. Then stop the engine and wait a few minutes to allow the oil drain back. Check the oil level again and if necessary, add more engine oil.
B Recommended grade and viscosity
CAUTION
Use only engine oil with the recommended grade and viscosity.
Oil grade: API classification SL or SJ with the words “ENERGY CONSERVING II” (if you cannot obtain the oil with SL or SJ grade, you may use SH grade oil.) or the new API certification mark (Starburst mark) dis- played on the container.
New API Certification Mark (Starburst Mark)
API Service label
1 Indicates the oil quality by API designations 2 Indicates the SAE oil viscosity grade 3 Indicates that the oil has fuel saving capabilities
11-12
Legacy U.S.A..(ENG.)A2290BE–A
Maintenance and service
In choosing an oil, you want the proper quality and viscosity, as well as one that will add to fuel economy. The following table lists the rec- ommended viscosities and applicable temperatures. When adding oil, different brands may be used together as long as they are the same API classification and SAE viscosity as those rec- ommended by SUBARU.
Engine oil viscosity (thickness) affects fuel economy. Oils of lower vis- cosity provide better fuel economy. However, in hot weather, oil of higher viscosity is required to properly lubricate the engine.
SAE viscosity numbr and applicable temperature
OM-H2756
B Recommended grade and viscosity under severe driving
conditions
If the vehicle is used in desert areas, in areas with very high tempera- tures, or used for heavy-duty applications such as a towing a trailer, use of oil with the following grade and viscosities is recommended.
API classification SL or SJ: SAE viscosity No.: 30, 40, 10W-50, 20W-40, 20W-50
11
– CONTINUED –
11-13
Legacy U.S.A..(ENG.)A2290BE–A
Cooling system
WARNING
Never attempt to remove the radiator cap until the engine has been shut off and has cooled down completely. Since the coolant is under pressure, you may suffer serious burns from a spray of boiling hot coolant when the cap is removed.
CAUTION
D The cooling system has been filled at the factory with a high quality, corrosion-inhibiting, year-around coolant which provides protection against freezing down to –33°F (–36°C). For adding, use genuine SUBARU coolant or an equivalent: a mixture of 50% soft water and 50% ethylene-glycol basis coolant. Use of improp- er coolants may result in corrosion in the cooling system. It is im- portant to maintain protection against freezing and corrosion, even if freezing temperatures are not expected. Never mix differ- ent kinds of coolant. D Do not splash the engine coolant over painted parts. The alco- hol contained in the engine coolant may damage the paint sur- face.
B Hose and connections Your vehicle employs an electric cooling fan which is thermostatically controlled to operate when the engine coolant reaches a specific tem- perature. If the radiator cooling fan does not operate even when the engine coolant temperature gauge exceeds the normal operating range, the cooling fan circuit may be defective. Check the fuse and replace it if necessary. If the fuse is not blown, have the cooling system checked by your SUBARU dealer. If frequent addition of coolant is necessary, there may be a leak in the engine cooling system. It is recommended that the cooling system and connections be checked for leaks, damage, or looseness.
11-14
Legacy U.S.A..(ENG.)A2290BE–A
Maintenance and service
J Engine coolant
B Checking the coolant level Check the coolant level at each fuel stop.
HBB004FB
1. Check the coolant level on the outside of the reservoir while the engine is cool. 2. If the level is close to or lower than the “LOW” level mark, add coolant up to the “FULL” level mark. If the reserve tank is empty, re- move the radiator cap and refill as required.
Rubber gaskets
11
HG0115
3. After refilling the reserve tank and the radiator, reinstall the caps and check that the rubber gaskets inside the radiator cap are in the proper position.
– CONTINUED –
11-15
Legacy U.S.A..(ENG.)A2290BE–A
B Changing the coolant
WARNING
Never attempt to remove the radiator cap until the engine has been shut off and has cooled down completely. Since the coolant is under pressure, you may suffer serious burns from a spray of boiling hot coolant when the cap is removed.
Change the engine coolant using the following procedures according to the maintenance schedule in the “Warranty and Maintenance Book- let”. 1. Remove the under cover. 2. Place a proper container under the drain plug and loosen the drain plug.
HBB006BB
HBB059BB
3. Loosen the radiator cap to drain the coolant from the radiator. Then drain the coolant from the reserve tank. Tighten the drain plug secure- ly.
11-16
Legacy U.S.A..(ENG.)A2290BE–A
Maintenance and service
HBB007CB
HBB004FB
4. Slowly pour the coolant and fill to the radiator filler neck and to the reserve tank’s “FULL” level mark. Do not pour the coolant too quickly, as this may lead to insufficient air bleeding and trapped air in the sys- tem.
Coolant capacity:
2.5 liter models
3.0 liter models
MT. 7.2 US qt (6.8 liters, 6.0 Imp qt) AT. 7.1 US qt (6.7 liters, 5.9 Imp qt) 8.4 US qt (7.9 liters, 7.0 Imp qt)
Rubber gaskets
11
HG0115
5. Put the radiator cap back on and tighten firmly. At this time, make sure that the rubber gasket in the radiator cap is correctly in place. 6. Start and run the engine for more than five minutes at 2,000 to 3,000 rpm.
– CONTINUED –
11-17
Legacy U.S.A..(ENG.)A2290BE–A
7. Stop the engine and wait until the coolant cools down (122 to 140°F [50 to 60°C]). If there is any loss of coolant, add coolant to the radiator’s filler neck and to the reserve tank’s “FULL” level. 8. Put the radiator cap and reservoir cap back on and tighten firmly.
Air cleaner element
WARNING
Do not operate the engine with the air cleaner element removed. The air cleaner element not only filters intake air but also stops flames if the engine backfires. If the air cleaner element is not installed when the engine backfires, you could be burned.
The air cleaner element functions as a filter screen. When the element is perforated or removed, engine wear will be excessive and engine life shortened.
The air cleaner element is a viscous type. It is unnecessary to clean or wash the element.
B Replacing the air cleaner element Replace the air cleaner element according to the maintenance sched- ule in the “Warranty and Maintenance Booklet”. Under extremely dusty conditions, replace it more frequently. It is recommended that you always use genuine SUBARU parts.
11-18
Legacy U.S.A..(ENG.)A2290BE–A
n 2.5 liter models
Maintenance and service
HBB063BB
HBB064BB
1. Remove the bolt securing the rear air cleaner element case. 2. Unsnap the three clamps holding the rear air cleaner element case. 3. Separate the rear air cleaner element case from the front air clean- er element case and remove the air cleaner element. 4. Clean the inside of the front and rear air cleaner element cases with a damp cloth and install a new air cleaner element. 5. Insert the four projections on the rear air cleaner element case into the slits on the front air cleaner element case and snap the three clamps on the rear air cleaner element case and then tighten the bolt.
n 3.0 liter models
11
1. Unsnap the two clamps holding the air cleaner case cover.
HBB056BA
– CONTINUED –
11-19
Legacy U.S.A..(ENG.)A2290BE–A
2. Open the air cleaner case cover and remove the air cleaner ele- ment. 3. Clean the inside of the air cleaner cover and case with a damp cloth and install a new air cleaner element.
HBB057BA
To install the air cleaner case cover, insert the two projections on the air cleaner case cover into the slits on the air cleaner case and then snap the two clamps on the air cleaner case cover.
Spark plugs
CAUTION
D When disconnecting the spark plug cables, always grasp the spark plug cap, not the cables. D Make sure the cables are replaced in the correct order.
11-20
Legacy U.S.A..(ENG.)A2290BE–A
Maintenance and service
HBA004BA
It may be difficult to replace the spark plugs. It is recommended that you have the spark plugs replaced by your SUBARU dealer.
The spark plugs should be replaced according to the maintenance schedule in the “Warranty and Maintenance Booklet”.
B Recommended spark plugs
2.5 liter models:
RC10YC4 (Champion) BKR6E-11 (NGK) BKR5E-11 (NGK)
