Login- Download PDF Manual
-
dealer/retailer within 100 miles (161 kilometers) of driving to have the tire inspected and repaired. If the sealant is not removed from the tire within 100 miles (161 kilometers) of driving, it is more likely that the tire can get damaged and have to be replaced.
A. Air Compressor B. Tire Sealant
Canister
C. Air Compressor Accessory Plug
D. On/Off Switch E. Air Pressure Gage F. Air Compressor
Inflator Hose
G. Sealant Filling Hose
321
Accessing the Tire Inflator Kit To access the tire inflator kit: 1. Open the trunk. See Trunk on page 97 for
more information.
Tire Sealant The kit contains a liquid sealant that when injected into a flat tire, can temporarily repair nail holes or cuts in the tread area of the tire. The tire sealant cannot repair tire damage caused while driving on a flat tire or a tire that has had a “blow out”, or a tire that has punctures in the sidewall areas. The tire sealant solution is to be used for a single tire and can only be used once. Check the tire sealant expiration date on the sealant canister. The sealant might not be as effective beyond the expiration date. If needed, see your dealer/retailer for a replacement canister.
2. Remove the tire inflator kit strap by turning
the wing nut counterclockwise.
3. Remove the inflator kit from its foam container.
322
Using the Tire Inflator Kit To use the tire inflator kit: 1. Place the inflator kit on the ground and unwrap the sealant filling hose from the compressor.
2. Remove the air compressor accessory plug from the unit. To do this, pull the top portion of the wrapped cord out first, then the bottom, and then unsnap the plug. Do not insert the plug into an accessory outlet yet.
3. Remove the valve stem cap from the flat tire
by turning it counterclockwise. If an object, such as a nail, has penetrated the tire, do not remove it.
4. Attach the sealant filling hose (A) onto the tire
valve stem. Turn it clockwise until it is tight. Make sure the inflator kit on/off switch (B) is in the O (off) position.
5. Plug the air compressor accessory plug (C)
into an accessory power outlet in the vehicle. See Accessory Power Outlet(s) on page 153
for more information.323
{CAUTION:
{CAUTION:
Idling the engine in a closed-in place or with the climate control system off can cause deadly carbon monoxide (CO). See Engine Exhaust on page 123.
6. Start the vehicle. See Starting the Engine
(Automatic Engine Start/Stop) on page 110
for more information. The vehicle must be running while using the air compressor.Inflating something too much can make it explode, and you or others could be injured. Be sure to read the inflator instructions, and inflate the tire to its recommended pressure. Do not exceed 36 psi (248 kPa).
7. Push the inflator kit switch to the I (on)
position. The inflator kit forces sealant and air into the tire. Sealant could leak from the puncture hole until the vehicle is driven and the hole has sealed.
324
8. Make sure there is a proper connection
between the tire valve stem and the sealant filling hose by looking at the air pressure gage. If there is not a pressure reading while the compressor is running, the connection between the inflator kit and the tire is bad. Check the attachment between the sealant filling hose and the tire valve stem.
9. Inflate the tire up to the recommended
inflation pressure, found on the Tire and Loading Information label located on the vehicle’s center pillar (B-pillar) below the vehicle’s door latch, using the air pressure gage on the top of the unit. The pressure gage reading is slightly high while the compressor is on. Turn the compressor off to get an accurate pressure reading.
If the recommended pressure cannot
Notice: be reached after 15 minutes, the vehicle should not be driven farther. Damage to the tire is severe and the sealant will not be effective. Remove the air compressor plug from the accessory power outlet and unscrew the inflating hose from the tire valve. See Roadside Assistance Program on page 377. 10. Push the inflator kit switch to the O (off) position once the correct tire pressure is obtained.
11. Turn off the engine.
325
12. Unplug the air compressor accessory plug
from the accessory power outlet in the vehicle.
13. Disconnect the sealant filling hose from the
tire valve stem, by turning it counterclockwise, and replace the tire valve stem cap. Be careful when handling the tire inflator components as they could be hot after usage.
14. Wrap the sealant filling hose around the air compressor channel to stow it in its original location.
15. Stow the air compressor accessory plug back in the air compressor. To do this, wrap the air compressor accessory plug, snap in the plug, and then push in the bottom and then the top of the wrapped air compressor accessory plug.
16. If the flat tire was
able to inflate to the recommended inflation pressure, remove the maximum speed label from the sealant canister.
Place it in a highly visible location such as the inside of the upper left corner of the windshield or to the face of the radio/clock. The maximum speed label reminds you to drive cautiously and not to exceed 55 mph (90 km/h) until you have the damaged tire inspected and repaired.
326
17. Return the equipment to the proper storage
location in the trunk of your vehicle. Turn the wing nut clockwise to secure the tire inflator kit.
{CAUTION:
Storing the tire inflator kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire inflator kit in the proper place.
18. Immediately drive the vehicle 5 miles (8 km)
to distribute the sealant evenly in the tire. Stop at a safe location and check the tire pressure, refer to Steps 1 through 8 under “Using the Air Compressor without Sealant” next in this section. If the tire pressure has fallen more then 10 psi (68 kPa), below the recommended inflation pressure, stop driving the vehicle. The tire is too damaged for the sealant to work. See Roadside Assistance Program on page 377.
327
Using the Air Compressor without Sealant To use the air compressor by itself to inflate a tire: 1. Remove the air compressor accessory plug
from the air compressor.
If the tire pressure has not dropped more than 10 psi (68 kPa) from the recommended inflation pressure, inflate the tire back up to the recommended inflation pressure.
19. Dispose of the sealant canister at a local dealer/retailer or in accordance with local state codes and practices. After using the sealant canister, replace it with a new canister from your dealer/retailer. 20. After temporarily repairing a tire with the
emergency flat tire repair kit, take your vehicle to your dealer/retailer to have the tire inspected and repaired.
2. Unlock the air compressor hose from the
sealant canister by pulling up on the lever.
3. Pull the air compressor inflator hose from the
sealant canister.
328
4. Push the air compressor inflator hose onto the
tire valve stem and push the lever down to secure in place.
5. Plug the air compressor accessory plug into
an accessory power outlet in the vehicle. See Accessory Power Outlet(s) on page 153 for more information.
{CAUTION:
Idling the engine in a closed-in place or with the climate control system off can cause deadly carbon monoxide (CO). See Engine Exhaust on page 123.
6. Start the vehicle. See Starting the Engine
(Automatic Engine Start/Stop) on page 110
for more information. The vehicle must be running while using the air compressor.{CAUTION:
Inflating something too much can make it explode, and you or others could be injured. Be sure to read the inflator instructions, and inflate the tire to its recommended pressure. Do not exceed 36 psi (248 kPa).
7. Push the inflator kit switch to the I (on)
position.
8. Make sure there is a proper connection between the tire valve stem and the air compressor hose by looking at the air pressure gage. If there is not a pressure reading while the compressor is running, the connection between the inflator kit and the tire is bad. Check the attachment between the air compressor hose and the tire valve stem.
329
9. Inflate the tire up to the recommended
inflation pressure using the air pressure gage on the top of the unit.
10. Turn off the air compressor by moving the
switch to the O (off) position.
11. Disconnect the compressor inflator hose and wrap the hose in the bottom of the inflator kit.
{CAUTION:
Storing the tire inflator kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire inflator kit in the proper place.
12. Place the equipment in the original location in
the trunk of your vehicle.
330
Removal and Installation of the Sealant Canister To remove the sealant canister:
1. Unlock the air compressor inflator hose from
the sealant canister by pulling the lever up. 2. Disconnect the air compressor inflator hose
from the sealant canister.
3. Unwrap the sealant filling hose from the
compressor.
To install a new sealant canister: 1. Align the sealant filling hose with the slot in
the air compressor.
2. Push the sealant canister down and turn it
clockwise.
3. Wrap the sealant filling hose around the air compressor channel to stow it in its original location.
4. Push the air compressor inflator hose onto the sealant canister inlet and push the lever down.
331
4. Turn the sealant canister so the inflator filling
hose is aligned with the slot in the compressor.
5. Lift the sealant canister from the compressor and replace with a new sealant canister. See your dealer/retailer for more information.
Appearance Care
Cleaning the Inside of Your Vehicle Your vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on your upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from your upholstery. It is important to keep your upholstery from becoming and remaining heavily soiled. Soils should be removed as quickly as possible. Your vehicle’s interior may experience extremes of heat that could cause stains to set rapidly. Lighter colored interiors may require more frequent cleaning. Use care because newspapers and garments that transfer color to your home furnishings may also transfer color to your vehicle’s interior. When cleaning your vehicle’s interior, only use cleaners specifically designed for the surfaces being cleaned. Permanent damage may result from using cleaners on surfaces for which they were not intended. Use glass cleaner only on
332
If you use abrasive cleaners when
glass. Remove any accidental over-spray from other surfaces immediately. To prevent over-spray, apply cleaner directly to the cleaning cloth. Notice: cleaning glass surfaces on your vehicle, you could scratch the glass and/or cause damage to the rear window defogger. When cleaning the glass on your vehicle, use only a soft cloth and glass cleaner. Many cleaners contain solvents that may become concentrated in your vehicle’s breathing space. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning your vehicle’s interior, maintain adequate ventilation by opening your vehicle’s doors and windows. Dust may be removed from small buttons and knobs using a small brush with soft bristles. Your retailer has a product for cleaning your vehicle’s glass. Should it become necessary, you can also obtain a product from your retailer to remove odors from your vehicle’s upholstery.
Do not clean your vehicle using the following cleaners or techniques: (cid:129) Never use a knife or any other sharp object to
remove a soil from any interior surface.
(cid:129) Never use a stiff brush. It can cause damage
to your vehicle’s interior surfaces. (cid:129) Never apply heavy pressure or rub
aggressively with a cleaning cloth. Use of heavy pressure can damage your interior and does not improve the effectiveness of soil removal.
(cid:129) Use only mild, neutral-pH soaps. Avoid
laundry detergents or dishwashing soaps with degreasers. Using too much soap will leave a residue that leaves streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide.
(cid:129) Do not heavily saturate your upholstery while
cleaning.
(cid:129) Damage to your vehicle’s interior may result from the use of many organic solvents such as naptha, alcohol, etc.
Fabric/Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats. For soils, always try to remove them first with plain water or club soda. Before cleaning, gently remove as much of the soil as possible using one of the following techniques: (cid:129) For liquids: gently blot the remaining soil
with a paper towel. Allow the soil to absorb into the paper towel until no more can be removed.
(cid:129) For solid dry soils: remove as much as
possible and then vacuum.
333
To clean, use the following instructions: 1. Saturate a lint-free, clean white cloth with
water or club soda.
2. Wring the cloth to remove excess moisture. 3. Start on the outside edge of the soil and gently
rub toward the center. Continue cleaning, using a clean area of the cloth each time it becomes soiled.
4. Continue to gently rub the soiled area until the
cleaning cloth remains clean.
5. If the soil is not completely removed, use a mild soap solution and repeat the cleaning process that was used with plain water.
If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness first. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface. After the cleaning process has been completed, a paper towel can be used to blot excess moisture from the fabric or carpet.
334
Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt. Never use spot lifters or removers on plastic surfaces. Many commercial cleaners and coatings that are sold to preserve and protect soft plastic surfaces may permanently change the appearance and feel of your interior and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean your vehicle’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Some commercial products may increase gloss on your instrument panel. The increase in gloss may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions.
Care of Safety Belts Keep belts clean and dry.
{CAUTION:
Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.
Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required. See Recommended Fluids and Lubricants on page 365.
Washing Your Vehicle The paint finish on your vehicle provides beauty, depth of color, gloss retention, and durability. The best way to preserve your vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water. Do not wash your vehicle in the direct rays of the sun. Use a car washing soap. Do not use strong soaps or chemical detergents. Be sure to rinse the vehicle well, removing all soap residue completely. You can get approved cleaning products from your retailer. See Vehicle Care/Appearance Materials on page 340. Do not use cleaning agents that are petroleum based, or that contain acid or abrasives. All cleaning agents should be flushed promptly and not allowed to dry on the surface, or they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter your vehicle.
335
Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing Your Vehicle on page 335.
Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish. You can get approved cleaning products from your Saturn retailer. See Vehicle Care/Appearance Materials on page 340. Your vehicle has a basecoat/clearcoat paint finish. The clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish.
Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/clearcoat paint finish on your vehicle. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather, and chemical fallout that can take their toll over a period of years. You can help to keep the paint finish looking new by keeping your vehicle in a garage or covered whenever possible.
336
Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner. Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer fluid or a mild detergent. Wash the windshield thoroughly when cleaning the blades. Bugs, road grime, sap, and a buildup of vehicle wash/wax treatments may cause wiper streaking. Replace the wiper blades if they are worn or damaged. Wipers can be damaged by: (cid:129) Extreme dusty conditions (cid:129) Sand and salt (cid:129) Heat and sun (cid:129) Snow and ice, without proper removal
Aluminum Wheels Notice: Chrome wheels and other chrome trim may be damaged if you do not wash your vehicle after driving on roads that have been sprayed with magnesium, calcium or sodium chloride. These chlorides are used on roads for conditions such as ice and dust. Always wash your vehicle’s chrome with soap and water after exposure. Notice: abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels, you could damage the surface of the wheel(s). The repairs would not be covered by your warranty. Use only approved cleaners on aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied.
If you use strong soaps, chemicals,
337
Notice: Using chrome polish on aluminum wheels could damage the wheels. The repairs would not be covered by your warranty. Use chrome polish on chrome wheels only. The surface of these wheels is similar to the painted surface of the vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because the surface could be damaged. Do not use chrome polish on aluminum wheels. Notice: If you drive your vehicle through an automatic car wash that has silicone carbide tire cleaning brushes, you could damage the aluminum or chrome-plated wheels. The repairs would not be covered by your warranty. Never drive a vehicle equipped with aluminum or chrome-plated wheels through an automatic car wash that uses silicone carbide tire cleaning brushes.
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.
338
Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your Saturn retailer. Larger areas of finish damage can be corrected in your Saturn retailer’s body and paint shop.
Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan and exhaust system even though they have corrosion protection.
At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of the frame should be loosened before being flushed. Your Saturn retailer or an underbody car washing system can do this for you.
Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on your vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, we will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within 12 months or 12,000 miles (20 000 km) of purchase, whichever occurs first.
339
Vehicle Care/Appearance Materials
Description
Usage
Description
Usage
Swirl Remover Polish
Polishing Cloth Wax-Treated
Tar and Road Oil Remover
Interior and exterior polishing cloth.
Removes tar, road oil, and asphalt.
Chrome Cleaner and Polish
Use on chrome or stainless steel.
White Sidewall Tire Cleaner
Removes soil and black marks from whitewalls.
Vinyl Cleaner
Cleans vinyl.
Glass Cleaner
Chrome and Wire Wheel Cleaner
Finish Enhancer
Removes dirt, grime, smoke, and fingerprints.
Removes dirt and grime from chrome wheels and wire wheel covers.
Removes dust, fingerprints, and surface contaminants. Spray on wipe off.
Cleaner Wax
Foaming Tire Shine Low Gloss
Wash Wax Concentrate
Spot Lifter
Odor Eliminator
Removes swirl marks, fine scratches, and other light surface contamination.
Removes light scratches and protects finish.
Cleans, shines, and protects in one easy step. No wiping necessary.
Medium foaming shampoo. Cleans and lightly waxes. Biodegradable and phosphate free.
Quickly and easily removes spots and stains from carpets, vinyl, and cloth upholstery.
Odorless spray odor eliminator used on fabrics, vinyl, leather, and carpet.
340
Vehicle Identification
Vehicle Identification Number (VIN)
This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration.
Engine Identification The eighth character in the VIN is the engine code. This code helps you identify your vehicle’s engine, specifications, and replacement parts.
Service Parts Identification Label This label is on the inside of the glove box. It is very helpful if you ever need to order parts. The label has the following information: (cid:129) Vehicle Identification Number (VIN) (cid:129) Model designation (cid:129) Paint information (cid:129) Production options and special equipment Do not remove this label from the vehicle.
341
Electrical System
Add-On Electrical Equipment Notice: Do not add anything electrical to your vehicle unless you check with your retailer first. Some electrical equipment can damage your vehicle and the damage would not be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should. Your vehicle has an airbag system. Before attempting to add anything electrical to your vehicle, see Servicing Your Airbag-Equipped Vehicle on page 82.
Windshield Wiper Fuses The windshield wiper motor is protected by an internal circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem, have it fixed.
Power Windows and Other Power Options Fuses in the fuse block protect the power windows. When the current load is too heavy, the fuse opens protecting the circuit until the problem is fixed.
342
Instrument Panel Fuse Block
Fuses The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible links. This greatly reduces the chance of damage caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure to replace a bad fuse with a new one of the identical size and rating. There are three fuse blocks in your vehicle: one in the center of the instrument panel, one in the engine compartment and one in the trunk. There is a fuse puller located on the instrument panel fuse block. It can be used to easily remove fuses from the fuse block.
The instrument panel fuse block is located on the passenger’s side of the vehicle, on the lower portion of the instrument panel near the floor. Remove the panel cover to access the fuse block, then remove the fuse block cover to access the fuses.
343
Your vehicle might not have all the fuses and features listed.
344
Fuses
Usage
Fuses
Usage
POWER MIRRORS NOT INSTALLED Not Used
Power Mirrors
RUN/CRANK
Cruise Control Switch, Passenger Airbag Status Indicator Heating Ventilation Air Conditioning Blower - High Speed Relay
HVAC BLOWER HIGH CLUSTER/THEFT Instrument Panel Cluster, Theft Deterrent System OnStar® ONSTAR NOT INSTALLED Not Used AIRBAG (IGN)
Airbag (Ignition) Heating Ventilation Air Conditioning Control Diagnostic Link Connector (Battery) Adjustable Pedals Windshield Wiper/Washer Switch Ignition Switch
Steering Wheel Illumination
HVAC CTRL (BATT)
PEDAL WIPER SW IGN SENSOR STRG WHL ILLUM NOT INSTALLED Not Used RADIO INTERIOR LIGHTS
Audio System
Interior Lamps
Not Used
Power Windows
REAR WIPER POWER WINDOWS HVAC CTRL (IGN) Heating Ventilation Air Conditioning Control (Ignition) Heating Ventilation Air Conditioning Blower Switch Door Locks
HVAC BLOWER
Sunroof, Power Windows
DOOR LOCK ROOF/HEAT SEAT NOT INSTALLED Not Used NOT INSTALLED Not Used AIRBAG (BATT) SPARE FUSE HOLDER SPARE FUSE HOLDER SPARE FUSE HOLDER SPARE FUSE HOLDER FUSE PULLER
Airbag (Battery)
Spare Fuse Holder
Spare Fuse Holder
Spare Fuse Holder
Spare Fuse Holder
Fuse Puller
345
Engine Compartment Fuse Block Your vehicle might not have all the fuses and features listed. The engine compartment fuse block is located on the driver side of the engine compartment, near the battery. Notice: Spilling liquid on any electrical components on your vehicle may damage it. Always keep the covers on any electrical component.
346
Fuses
11
12
13
1415
16
17
1819
Usage Air Conditioner Clutch Electronic Throttle Control Belt Alternator Starter (BAS) IGN Transmission, Transmission Control Module Ignition 1
Belt Alternator Starter (BAS) Pumps Emission Left Headlamp Low-Beam Horn Right Headlamp Low-Beam Left Headlamp High-Beam Right Headlamp High-Beam Engine Control Module BATT Windshield Wiper Anti-lock Brake System (ABS) (IGN 1) Engine Control Module (IGN 1) Cooling Fan 1
Cooling Fan 2
Run Relay, Heating, Ventilation, Air Conditioning BlowerFuses
20
21
22
23
24
25
26
4142
43
44
46
47
50
51
52
54Usage Body Control Module 1
Body Control Module Run/Crank Rear Electrical Center 1
Rear Electrical Center 2
Anti-lock Brake System (ABS) Body Control Module 2
Starter Electric Power Steering Transmission Control Module Battery Ignition Module Injectors Daytime Running Lamps Center High-Mounted Stoplamps Driver Power Window Belt Alternator Starter (BAS) BATT Transmission Pump Motor Battery Voltage Sense347
Relays
Usage
Rear Compartment Fuse Block
28
29
30
31
32
33
34
35
37
38
39
40
48
49
53Cooling Fan 1
Cooling Fan Series/Parallel Cooling Fan 2
Starter Run/Crank, Ignition Powertrain Air Conditioning Clutch High-Beam Headlamp Horn Low-Beam Headlamp Windshield Wiper 1
Windshield Wiper 2
Daytime Running Lamps (DRL) Stoplamps Transmission Pump MotorDiodes
27
Wiper
Usage
348
The rear compartment fuse block is located in the trunk of the vehicle. Access the fuse block through the trunk panel on the driver’s side of the rear cargo area.
Fuses
Usage
Fuses
Usage
Passenger Seat Controls Driver Seat Controls Not Used Not Used
Belt Alternator Starter (BAS) Park Lamps, Instrument Panel Dimming Not Used Not Used
349
Fuses
Usage
Relays
10
11
12
13
14
1516
17
18
19
20
21
22
23
24
25Not Used Sunroof Controls Not Used Not Used Audio Amplifier Heated Seat Controls Not Used Remote Keyless Entry (RKE) System, XM™ Satellite Radio Back-up Lamps Not Used Not Used Auxiliary Power Outlets Not Used Trunk Release Rear Defog Heated Mirrors Fuel Pump
26
27
28
29
30
31
32
33
34
35
36
3738 (Diode)
Usage
Rear Window Defogger Park Lamps Not Used Not Used Not Used Not Used Not Used Back-up Lamps Not Used Not Used Trunk Release Fuel Pump Cargo Lamp
350
Capacities and Specifications The following approximate capacities are given in English and metric conversions. Please refer to Recommended Fluids and Lubricants on page 365 for more information.
Application
Air Conditioning Refrigerant R134a
Capacities
English
Metric
For the air conditioning system refrigerant charge amount, see the refrigerant caution label located
under the hood. See your retailer for more
information.
7.7 L Cooling System 6.6 L Transaxle (Bottom Pan Removal) 4.7 L Engine Oil with Filter 61.7 L Fuel Tank 140 Y Wheel Nut Torque All capacities are approximate. When adding, be sure to fill to the appropriate level, as recommended in this manual.
8.1 qt 7.0 qt 5.0 qt 16.3 gal 100 lb ft
Engine 2.4L L4
VIN Code
Transaxle Automatic
Spark Plug Gap
0.040 inches (1.01 mm)
Engine Specifications
351
✍ NOTES
352
Section 6
Maintenance Schedule
Maintenance Schedule ................................ 354
Introduction ............................................... 354
Maintenance Requirements ........................ 354
Your Vehicle and the Environment ............ 354
Using the Maintenance Schedule ............... 354
Scheduled Maintenance ............................. 356
Additional Required Services ..................... 359
Maintenance Footnotes .............................. 360Owner Checks and Services ..................... 362
At Each Fuel Fill ....................................... 362
At Least Once a Month ............................. 362
At Least Once a Year ............................... 363
Recommended Fluids and Lubricants ........ 365
Normal Maintenance Replacement Parts ... 366
Engine Drive Belt Routing ......................... 367
Maintenance Record .................................. 368353
Maintenance Schedule
Introduction Important: Keep engine oil at the proper level and change as recommended.
Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition. Any damage caused by failure to follow scheduled maintenance might not be covered by warranty.
Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. All recommended maintenance is important. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle. To help protect our environment, and to keep your vehicle in good condition, be sure to maintain your vehicle properly.
Using the Maintenance Schedule We at Saturn want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather. You may use your vehicle in making deliveries. Or you may drive it to work, to do errands, or in many other ways.
354
Because of all the different ways people use their vehicles, maintenance needs vary. You may need more frequent checks and replacements. So please read the following and note how you drive. If you have any questions on how to keep your vehicle in good condition, see your Saturn retailer. This schedule is for vehicles that:
carry passengers and cargo within recommended limits. You will find these limits on the Tire and Loading Information label. See Loading Your Vehicle on page 242. are driven on reasonable road surfaces within legal driving limits. use the recommended fuel. See Gasoline Octane on page 255.
The services in Scheduled Maintenance on page 356 should be performed when indicated. See Additional Required Services on page 359 and Maintenance Footnotes on page 360 for further information.
{CAUTION:
Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job. If you have any doubt, see your retailer to have a qualified technician do the work. See Doing Your Own Service Work on page 254.
Some maintenance services can be complex. So, unless you are technically qualified and have the necessary equipment, you should have your Saturn retailer do these jobs. When you go to your Saturn retailer for your service needs, you will know that Saturn-trained and supported service technicians will perform the work using genuine Saturn parts.
355
(cid:129) (cid:129) (cid:129) If you want to purchase service information, see Service Publications Ordering Information on page 387. Owner Checks and Services on page 362 tells you what should be checked, when to check it, and what you can easily do to help keep your vehicle in good condition. The proper replacement parts, fluids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 365 and Normal Maintenance Replacement Parts on page 366. When your vehicle is serviced, make sure these are used. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle. We recommend the use of genuine Saturn parts.
Scheduled Maintenance When the CHANGE OIL SOON message in the Driver Information Center (DIC) comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year. However, the engine oil and filter must be changed at least once a year and at this time the system must be reset. Your dealer/retailer has trained service technicians who will perform this work using genuine parts and reset the system. If the engine oil life system is ever reset accidentally, you must service your vehicle within 3,000 miles (5 000 km) since your last service. Remember to reset the oil life system whenever the oil is changed. See Engine Oil Life System on page 268 for information on the Engine Oil Life System and resetting the system.
356
When the CHANGE OIL SOON message appears, certain services, checks, and inspections are required. Required services are described in the following for “Maintenance I” and “Maintenance II.” Generally, it is recommended that your first service be Maintenance I, your second service be Maintenance II, and that you alternate Maintenance I and Maintenance II thereafter. However, in some cases, Maintenance II might be required more often.
Maintenance I — Use Maintenance I if the message comes on within 10 months since the vehicle was purchased or Maintenance II was performed. Maintenance II — Use Maintenance II if the previous service performed was Maintenance I. Always use Maintenance II whenever the message comes on 10 months or more since the last service or if the message has not come on at all for one year.
Scheduled Maintenance
Service
Maintenance I Maintenance II
Change engine oil and filter. See Engine Oil on page 265. Reset oil life system. See Engine Oil Life System on page 268. An Emission Control Service. Visually check for any leaks or damage. See footnote (j). Inspect engine air cleaner filter. If necessary, replace filter. See Engine Air Cleaner/Filter on page 270. See footnote (k). Rotate tires and check inflation pressures and wear. See Tire Inspection and Rotation on page 310 and At Least Once a Month on page 362.
•
•
•
•
•
•
•
357
Scheduled Maintenance (cont’d) Service
Maintenance I Maintenance II
Inspect brake system. See footnote (a). Check engine coolant and windshield washer fluid levels and add fluid as needed. Perform any needed additional services. See “Additional Required Services” in this section. Inspect suspension and steering components. See footnote (b). Inspect engine cooling system. See footnote (c). Inspect wiper blades. See footnote (d). Inspect restraint system components. See footnote (e). Lubricate body components. See footnote (f). Inspect throttle system. See footnote (g).
•
•
•
•
•
•
• • • • • •
358
Additional Required Services The following services should be performed at the first maintenance service (I or II) after the indicated miles (kilometers) shown for each item.
Service and Miles (Kilometers)
Additional Required Services 75,000
25,000
(40 000)50,000
(80 000)(120 000)
•
•
•
•
•
•
•
•
Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components. Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 270. Change automatic transmission fluid and filter (severe service only). See footnote (h). Replace spark plugs. Inspect spark plug wires. An Emission Control Service. Engine cooling system service (or every five years, whichever occurs first). An Emission Control Service. See footnote (i). Inspect engine accessory drive belt. An Emission Control Service. See footnote (m).
100,000
(160 000)125,000
(200 000)150,000
(240 000)•
•
•
•
•
•
•
•
•
•
•
•
•
359
Maintenance Footnotes (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect other brake parts, including calipers, parking brake, etc. (b) Visually inspect front and rear suspension and steering system for damaged, loose, or missing parts or signs of wear. Inspect electric power steering cables for proper hook-up, binding, cracks, chafing, etc. (c) Visually inspect hoses and have them replaced if they are cracked, swollen, or deteriorated. Inspect all pipes, fittings and clamps; replace with genuine parts as needed. To help ensure proper operation, a pressure test of the cooling system and pressure cap and cleaning the outside of the radiator and air conditioning condenser is recommended at least once a year.
(d) Inspect wiper blades for wear, cracking, or contamination. Clean the windshield and wiper blades, if contaminated. Replace wiper blades that are worn or damaged. See Windshield Wiper Blade Replacement on page 297 and Windshield and Wiper Blades on page 337 for more information. (e) Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors, and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced. Also look for any opened or broken airbag coverings, and have them repaired or replaced. The airbag system does not need regular maintenance. (f) Lubricate all key lock cylinders, door hinges and latches, hood hinges and latches, and trunk lid hinges and latches. More frequent lubrication may be required when exposed to a corrosive environment. Applying silicone grease on weatherstrips with a clean cloth will make them last longer, seal better, and not stick or squeak.
360
(g) Check system for interference or binding and for damaged or missing parts. Replace parts as needed. Replace any components that have high effort or excessive wear. Do not lubricate accelerator or cruise control cables. (h) Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:
− In heavy city traffic where the outside
temperature regularly reaches 90°F (32°C) or higher.
− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police, or delivery
service.
If you do not use your vehicle under any of these conditions, the fluid and filter do not require changing.
(i) Drain, flush, and refill cooling system. This service can be complex; you should have your dealer/retailer perform this service. See Engine Coolant on page 272 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap, and filler neck. Pressure test the cooling system and pressure cap. (j) A fluid loss in any vehicle system could indicate a problem. Have the system inspected and repaired and the fluid level checked. Add fluid if needed. (k) If you drive regularly under dusty conditions, inspect the filter at each engine oil change. (m) Visually inspect belt for fraying, excessive cracks, or obvious damage. Replace belt if necessary.
361
Engine Coolant Level Check Check the engine coolant level and add DEX-COOL® coolant mixture if necessary. See Engine Coolant on page 272. Windshield Washer Fluid Level Check Check the windshield washer fluid level in the windshield washer fluid reservoir and add the proper fluid if necessary.
At Least Once a Month Tire Inspection and Inflation Check Inspect your vehicle’s tires for wear and make sure they are inflated to the correct pressures. See Inflation - Tire Pressure on page 304.
Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure the safety, dependability, and emission control performance of your vehicle. Your Saturn retailer can assist you with these checks and services. Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to your vehicle, make sure they are the proper ones, as shown in Recommended Fluids and Lubricants on page 365.
At Each Fuel Fill It is important to perform these underhood checks at each fuel fill. Engine Oil Level Check Notice: regularly and keep it at the proper level. Failure to keep the engine oil at the proper level can cause damage to the engine not covered by your warranty. Check the engine oil level and add the proper oil if necessary. See Engine Oil on page 265.
It is important to check the engine oil
362
At Least Once a Year Starter Switch Check
{CAUTION:
When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.
1. Before you start, be sure you have enough
room around the vehicle.
2. Firmly apply both the parking brake and the
regular brake. See Parking Brake on page 119. Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts.
3. Try to start the engine in each gear. The vehicle should start only in PARK (P) or NEUTRAL (N). If the vehicle starts in any other position, contact your Saturn retailer for service.
Automatic Transaxle Shift Lock Control System Check
{CAUTION:
When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.
1. Before you start, be sure you have enough
room around the vehicle. It should be parked on a level surface.
2. Firmly apply the parking brake. See Parking
Brake on page 119. Be ready to apply the regular brake immediately if the vehicle begins to move. 3. With the engine off, turn the ignition to ON,
but do not start the engine. Without applying the regular brake, try to move the shift lever out of PARK (P) with normal effort. If the shift lever moves out of PARK (P), contact your Saturn retailer for service.
363
Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. (cid:129) To check the parking brake’s holding ability:
With the engine running and transaxle in NEUTRAL (N), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking brake only.
(cid:129) To check the PARK (P) mechanism’s holding
ability: With the engine running, shift to PARK (P). Then release the parking brake followed by the regular brake.
Contact your Saturn retailer if service is required. Underbody Flushing Service At least every spring, use plain water to flush any corrosive materials from the underbody. Take care to clean thoroughly any areas where mud and other debris can collect.
Ignition Transaxle Lock Check While parked, and with the parking brake set, try to turn the ignition to OFF in each shift lever position. (cid:129) The ignition should turn to OFF only when the
shift lever is in PARK (P).
(cid:129) The ignition key should come out only in OFF. Contact your Saturn retailer if service is required. Parking Brake and Automatic Transaxle Park (P) Mechanism Check
{CAUTION:
When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.
364
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer/retailer.
Usage
Engine Oil
Engine Coolant
Hydraulic
Brake System
Windshield
Washer
Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol. To determine the proper viscosity for your vehicle’s engine, see Engine Oil on page 265. 50/50 mixture of clean, drinkable water and use only DEX-COOL® Coolant. See Engine Coolant on page 272. Delco® Supreme 11 Brake Fluid or equivalent DOT-3 brake fluid.
Optikleen® Washer Solvent.
Usage
Automatic
Transmission
Key Lock Cylinders
Fluid/Lubricant
DEXRON®-VI Automatic Transmission Fluid. Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474).
Hood Latch Assembly, Secondary
Latch, Pivots, Spring Anchor, and Release
Pawl
Hood and
Door Hinges
Weatherstrip Conditioning
Lubriplate Lubricant Aerosol (GM Part No. U.S. 12346293, in Canada 992723) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB.
Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 109435474). Weatherstrip Lubricant (GM Part No. U.S. 3634770, in Canada 10953518) or Dielectric Silicone Grease (GM Part No. U.S. 12345579, in Canada 992887).
365
Normal Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your Saturn retailer.
Part
Part Numbers
Engine Air Cleaner/Filter Engine Oil Filter Spark Plugs Windshield Wiper Blades
Driver’s Side – 23.6 inches (60.0 cm) Passenger’s Side – 21.0 inches (53.0 cm)
22676970
12605566
1259800415779416
15779415ACDelco® Part
Numbers A1627C PF457G 41-103
— —
366
Engine Drive Belt Routing
The engine drive belt on this hybrid vehicle is under a higher tension than the engine drive belt on a non-hybrid vehicle and requires the use of a special kind of tool to service. See your dealer/retailer for service.
367
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 354. Any additional information from Owner Checks and Services on page 362 can be added on the following record pages. You should retain all maintenance receipts.
Date
Odometer Reading
Serviced By
Maintenance I or Maintenance II
Services Performed
Maintenance Record
368
Date
Odometer Reading
Serviced By
Maintenance I or Maintenance II
Services Performed
Maintenance Record (cont’d)
369
Date
Odometer Reading
Serviced By
Maintenance I or Maintenance II
Services Performed
Maintenance Record (cont’d)
370
Section 7
Customer Assistance Information
Customer Assistance and Information ....... 372
Customer Satisfaction Procedure ............... 372
Online Owner Center ................................. 375
Customer Assistance for TextTelephone (TTY) Users .......................... 376
Customer Assistance Offices ..................... 376
GM Mobility Reimbursement Program ........ 377
Roadside Assistance Program ................... 377
Courtesy Transportation ............................. 380
Collision Damage Repair ........................... 382Reporting Safety Defects ............................ 386
Reporting Safety Defects to the
United States Government ..................... 386
Reporting Safety Defects to the
Canadian Government ............................ 386
Reporting Safety Defects to Saturn ............ 387
Service Publications Ordering Information .... 387
Vehicle Data Recording and Privacy ......... 389
Event Data Recorders ............................... 389
OnStar ...................................................... 390
Navigation System ..................................... 391
Radio Frequency Identification (RFID) ........ 391371
Customer Assistance and Information
Customer Satisfaction Procedure Your satisfaction and goodwill are important to your retailer and to Saturn. Together we are committed to providing our customers with unparalleled service, before, during, and after the purchase of a Saturn vehicle, for total customer satisfaction. We call this the Saturn Difference. Normally, any concerns with the sales transaction or the operation of your vehicle are resolved by your retailer’s sales or service departments. If, for any reason, your ownership experience falls below your expectations, we suggest you take the following action:
STEP ONE: Contact the Retail Customer Assistance Liaison. Any member of the retail management team has the authority and the desire to resolve your concerns. Normally, concerns can be quickly resolved at this level.
STEP TWO: Should you need additional assistance, in the U.S., contact the Saturn Customer Assistance Center by calling 1-800-553-6000. In Canada, contact the Saturn Customer Communication Centre at 1-800-263-1999. A Saturn Customer Assistance Center team member will handle your call and assist in providing product and warranty information, the nearest retailer location, roadside assistance, brochures, literature and discuss any concerns you may have. We encourage you to call the toll-free number in order to give your inquiry prompt attention. Please have the following information available to give the Customer Assistance Representative: (cid:129) Vehicle Identification Number (VIN). This
17-digit number can be found on the vehicle registration or title, on the upper driver side corner of the dash, or on your roadside assistance key card.
(cid:129) The name of your selling and servicing retail
facility.
(cid:129) Vehicle delivery date and present mileage. (cid:129) Your daytime and evening phone numbers.
372
When contacting Saturn, please remember that your concern will likely be resolved at a retailer’s facility. That is why we suggest you follow Step One first if you have a concern.
STEP THREE (U.S. Owners): Both Saturn and its retailers are committed to making sure you are completely satisfied with your Saturn vehicle. However, if you continue to remain unsatisfied after following the procedure outlined in Steps One and Two, Saturn and its retailers offer the additional assistance of a neutral party through our voluntary participation in a mediation/arbitration program called Better Business Bureau (BBB) Auto Line. The BBB Auto Line Program is an out-of-court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty. This program is available at no cost to you, our customer.
Although you may be required to resort to this informal dispute resolution program prior to filing a court action, use of the program is free of charge and your case is generally heard within 40 days. If you do not agree with the decision given in your case, you can reject it and proceed with any other venue for relief available to you. Contact the BBB Auto Line Program by using the toll-free telephone number or by writing them at the following address:
BBB Auto Line Program Council of Better Business Bureaus, Inc. 4200 Wilson Boulevard Suite 800
Arlington, VA 22203-1838
Telephone: 1-800-955-5100This program is available in all 50 states and the District of Columbia. Eligibility is limited by vehicle age, mileage and other factors. Saturn Corporation reserves the right to change eligibility limitations and/or discontinue its participation in this program.
373
STEP THREE (Canadian Owners): General Motors Participation in the Mediation/Arbitration Program In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2, General Motors of Canada Limited has committed to binding arbitration of owner disputes involving factory-related vehicle service claims. The program provides for the review of the facts involved by an impartial third party arbiter, and may include an informal hearing before the arbiter. The program is designed so that the entire dispute settlement process, from the time you file your complaint to the final decision, should be completed in approximately 70 days. We believe our impartial program offers advantages over courts in most jurisdictions because it is informal, quick, and free of charge.
For further information concerning eligibility in the Canadian Motor Vehicle Arbitration Plan (CAMVAP), call toll-free 1-800-207-0685. Alternatively, you may call the Saturn Customer Communication Centre, 1-800-263-1999, or you may write to:
Mediation/Arbitration Program c/o Customer Communication Centre General Motors of Canada Limited Mail Code: CA1-163-005
1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7
Telephone: 1-800-955-5100Your inquiry should be accompanied by your Vehicle Identification Number (VIN).
374
Online Owner Center Online Owner Center (United States only) The Owner Center is a resource for your Saturn ownership needs. Specific vehicle information can be found in one place. The Online Owner Center allows you to: (cid:129) Get e-mail service reminders. (cid:129) Access information about your specific vehicle, including tips and videos and an electronic version of this owner manual. (cid:129) Keep track of your vehicle’s service history
and maintenance schedule.
(cid:129) Find Saturn retailers for service nationwide. (cid:129) Receive special promotions and privileges only
available to members.
My GM Canada (Canada only) My GM Canada is a password-protected section of gmcanada.com where you can save information on GM vehicles, get personalized offers, and use handy tools and forms with greater ease. Here are a few of the valuable tools and services you will have access to:
− My Showroom: Find and save information on
vehicles and current offers in your area.
− My Dealers/Retailers: Save details such as
address and phone number for each of your preferred GM Dealers or Retailers.
− My Driveway: Receive service reminders and
helpful advice on owning and maintaining your vehicle.
− My Preferences: Manage your profile,
subscribe to E-News and use tools and forms with greater ease.
Refer to www.saturn.com on the web for updated information and to register your vehicle.
To sign up to My GM Canada, visit the My GM Canada section within www.gmcanada.com.
375
Customer Assistance for Text Telephone (TTY) Users To assist owners who have hearing difficulties, Saturn has installed special TDD (Telecommunication Devices for the Deaf) equipment in its Saturn Customer Assistance Center. Any hearing- or speech-impaired customer who has access to a TDD or to a conventional Text Telephone (TTY) can communicate with Saturn by dialing 1-800-TDD-6000. TTY users in Canada may dial 1-800-263-3830.
Customer Assistance Offices Saturn encourages customers to call the toll-free number for assistance. If a customer wishes to write to Saturn, the letter should be addressed to:
Saturn Customer Assistance Center 100 Saturn Parkway Mail Code 371-999-S24
Spring Hill, TN 37174-1500
1-800-553-6000
1-800-833-6000 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-553-6000In Canada, write to:
Saturn Customer Communication Centre General Motors of Canada Ltd. CA1-163-005
1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7
www.gmcanada.com 1-800-263-1999
1-800-263-3830 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-268-6800376
GM Mobility Reimbursement Program
This program, available to qualified applicants, can reimburse you up to $1,000 toward eligible aftermarket driver or passenger adaptive equipment you may require for your vehicle such as hand controls, wheelchair/scooter lifts, etc. The offer is available for a limited period of time from the date of vehicle purchase/lease. For more details, or to determine your vehicle’s eligibility, visit your Saturn retailer or call the Saturn Customer Assistance Center at 1-800-553-6000. Text telephone (TTY) users, call 1-800-833-6000.
In Canada, customers may call the Saturn Customer Communication Centre at 1-800-263-1999. TTY users in Canada may call 1-800-263-3830.
Roadside Assistance Program For vehicles purchased in the U.S., call 1-800-553-6000; (Text Telephone (TTY): 1-800-833-6000). For vehicles purchased in Canada, call 1-800-268-6800. Service is available 24 hours a day, 365 days a year. As the owner of a new Saturn vehicle, you are automatically enrolled in the Saturn Roadside Assistance Program. Who is Covered? Roadside Assistance coverage is for the vehicle operator, regardless of ownership. In Canada, a person driving this vehicle without the consent of the owner is not eligible for coverage.
377
(cid:129) Flat Tire Change: Installation of a spare tire in
good condition, when equipped and properly inflated, is covered at no charge. The customer is responsible for the repair or replacement of the tire if not covered by a warrantable failure. Jump Start: A battery jump start is covered at no charge if the vehicle does not start.
(cid:129) Trip Routing Service (Canada only): Upon request, Roadside Assistance will send you detailed, computer personalized maps, highlighting your choice of either the most direct route or the most scenic route to your destination, anywhere in North America, along with helpful travel information pertaining to your trip. Please allow three weeks before your planned departure date. Trip routing requests are limited to six per calendar year.
Services Provided The following services are provided in the U.S. and Canada up to 5 years/100,000 miles (160 000 km), whichever comes first, and, in Canada only, up to a maximum of $100. (cid:129) Fuel Delivery: Delivery of enough fuel for the
vehicle to get to the nearest service station (approximately $5 Canada). In Canada, service to provide diesel may be restricted. For safety reasons, propane and other alternative fuels are not provided through this service.
(cid:129) Lock-out Service: Lock-out service is covered at no charge if you are unable to gain entry into your vehicle. A remote unlock may be available if you have an active OnStar® subscription. To ensure security, the driver must present personal identification before lock-out service is provided. In Canada, the vehicle registration is also required.
(cid:129) Emergency Tow From a Public Roadway
or Highway: Tow to the nearest Saturn
