2007 Saturn AURA Hybrid Owners Manual

Download PDF Manual
on and stays on, you may be able to restart your engine if you turn it off. Your PASS-Key® III+ system, however, is not working properly and must be serviced by your dealer/retailer. Your vehicle is not protected by the PASS-Key® III+ system at this time. If you lose or damage your PASS-Key® III+ key, see your dealer/retailer or a locksmith who can service PASS-Key® III+ to have a new key made. Do not leave the key or device that disarms or deactivates the theft deterrent system in the vehicle. Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: (cid:129) Do not drive at any one constant speed, fast or slow, for the ﬁrst 500 miles (805 km). Do not make full-throttle starts. Do not exceed 5,000 engine rpm. Avoid downshifting to brake, or slow, the vehicle. (cid:129) Avoid making hard stops for the ﬁrst 200 miles (322 km) or so. During this time the new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this breaking-in guideline every time you get new brake linings. (cid:129) Do not tow a trailer during break-in. See Towing a Trailer on page 250 for the trailer towing capabilities of your vehicle and more information. Following break-in, engine speed and load can be gradually increased. 107 Ignition Positions With the key in the ignition switch, you can turn it to four different positions. Notice: Using a tool to force the key from the ignition switch could cause damage or break the key. Use the correct key and turn the key only with your hand. Make sure the key is in all the way. If none of this works, then your vehicle needs service. 9(OFF): This is the only position from which you can remove the key. It also locks the ignition and transaxle. A warning chime sounds if the driver’s door is opened while the ignition is off and the key is left in the ignition. 108 ACC (ACCESSORY): This position lets you use things like the radio and windshield wipers while the engine is not running. Use this position if your vehicle must be pushed or towed, but never try to push-start your vehicle. See Recreational Vehicle Towing on page 247. R(ON): This position unlocks the ignition. It is also the position to where the key returns after you release the switch and the engine starts. The switch will stay in this position while the engine is running. But even while the engine is not running, you can use ON to operate the electrical accessories, and to display some instrument panel warning lights. The battery could be drained if you leave the key in the ACC or ON position with the engine off. You might not be able to start your vehicle if the battery is allowed to drain for an extended period of time. /(START): This position starts the engine. When the engine starts, release the key. The ignition switch will return to the ON position for normal driving. Key In the Ignition Never leave your vehicle with the keys inside, as it is an easy target for joy riders or thieves. If you leave the key in the ignition and park your vehicle, a chime sounds, when the driver’s door is opened. Always remember to remove the key from the ignition and take it with you. This locks your ignition and transaxle. Also, always remember to lock the doors. The battery could be drained if the key is left in the ignition while your vehicle is parked. You might not be able to start your vehicle after it has been parked for an extended period of time. Retained Accessory Power (RAP) These vehicle accessories can be used for up to 10 minutes after the engine is turned off: (cid:129) Audio System (cid:129) Power Windows (cid:129) Heated Seats (if equipped) (cid:129) Sunroof (if equipped) These features continue to work up to 10 minutes after the ignition is turned to LOCK/OFF. The power windows, heated seats, and sunroof will work until any door is opened. The radio continues to work until the driver’s door is opened. All these features operate when the key is in the ON/RUN or ACC/ACCESSORY. 109 Your vehicle has a Computer-Controlled Cranking System. This feature assists in starting the engine and protects components. If the key is turned to the START position, and then released when the engine begins cranking, the engine continues cranking for a few seconds or until the vehicle starts. If the engine does not start and the key is held in START for many seconds, cranking stops after 15 seconds to prevent cranking motor damage. To prevent gear damage, this system also prevents cranking if the engine is already running. Engine cranking can be stopped by turning the ignition switch to the ACC or LOCK position. Starting the Engine (Automatic Engine Start/Stop) The shift lever must be in PARK (P) or NEUTRAL (N) for the vehicle to start. To restart when the vehicle is already moving, use NEUTRAL (N) only. Notice: Shifting into PARK (P) with the vehicle moving could damage the transaxle. Shift into PARK (P) only when your vehicle is stopped. Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition key to START. When the engine starts, let go of the key. The idle speed goes down as your engine gets warm. Do not race the engine immediately after starting it. Operate the engine and transaxle gently to allow the oil to warm up and lubricate all moving parts. 110 Notice: Cranking the engine for long periods of time, by returning the key to the START position immediately after cranking has ended, can overheat and damage the cranking motor, and drain the battery. Wait at least 15 seconds between each try, to let the cranking motor cool down. 2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or −18°C), it could be ﬂooded with too much gasoline. Try pushing the accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for up to a maximum of 15 seconds. Wait at least 15 seconds between each try, to allow the cranking motor to cool down. When the engine starts, let go of the key and accelerator. If the vehicle starts brieﬂy but then stops again, do the same thing. This clears the extra gasoline from the engine. Do not race the engine immediately after starting it. Operate the engine and transaxle gently until the oil warms up and lubricates all moving parts. Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your retailer. If you do not, your engine might not perform properly. Any resulting damage would not be covered by your vehicle’s warranty. 111 Automatic Engine Start/Stop {CAUTION: Exiting your vehicle, without ﬁrst shifting into PARK (P), may cause the vehicle to move, you or others may be injured. Because your vehicle has the Automatic Engine Start/Stop feature, your vehicle’s engine might seem to be shut off, however, once the brake pedal is released, the engine could start up again. Shift to PARK (P) and turn the ignition to OFF, before exiting the vehicle. Your vehicle has an automatic engine start/stop feature. After the engine is started and has reached operating temperature, the AUTO STOP feature may cause the engine to turn off when you apply the brakes and come to a complete stop. When you take your foot off the brake pedal or press the accelerator pedal, the engine will start. The engine will continue to run until the next AUTO STOP. The AUTO STOP symbol on the tachometer signiﬁes that the engine is in AUTO STOP mode. See Auto Stop Mode on page 178 for more information. When the vehicle is turned off, the tachometer will move to OFF. If the driver’s door is opened while in AUTO STOP mode, a chime will sound. To restart the engine during the AUTO STOP, release the brake pedal or press the accelerator pedal. The engine starts immediately. The vehicle continues to run until the next stop. There are several conditions which may prevent an AUTO STOP or cause an AUTO START. 112 The Engine Will Remain Running When: (cid:129) The engine, transaxle, or hybrid battery is not warmed up yet. (cid:129) The outside temperature is approximately −4°F (−20°C). (cid:129) When the A/C is in Normal Mode. (cid:129) A/C is in Hybrid Mode and the climate control system is working to cool the vehicle. See Automatic Climate Control System on page 154 for more information. (cid:129) Defrost is selected. (cid:129) The shift lever is in PARK (P), NEUTRAL (N), REVERSE (R), INTERMEDIATE (I) or LOW (L). (cid:129) The hybrid battery pack charge is low. (cid:129) The 12V vehicle battery charge is low, or loads are high. (cid:129) The hood is not fully closed. The Engine Will Restart When: (cid:129) The brake pedal is released. (cid:129) The accelerator pedal is applied. (cid:129) When shifting out of DRIVE (D) to any other gear. If the A/C button is selected, the duration of the AUTO STOP will depend on the outside temperature. This economy mode improves fuel economy by limiting the effects of the air conditioning. The warmer it is outside, the shorter the time before the engine is restarted to provide cabin cooling. (cid:129) The climate control system is turned from Off to On (econ or normal A/C, or ﬂoor/ defog/defrost) See Automatic Climate Control System on page 154 for more information. 113 (cid:129) (cid:129) The engine is required to run for either heater or climate control performance. See “Air Conditioning Engine Start/Stop” under Automatic Climate Control System on page 154 for more information. (cid:129) The hybrid battery pack charge is low and requires recharging. (cid:129) Auto Stop time is greater than two minutes. Engine Coolant Heater Your vehicle may have this feature. In very cold weather, 0°F (−18°C) or colder, the engine coolant heater can provide easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle. At temperatures above 32°F (0°C), use of the coolant heater is not required. Your vehicle may also have an internal thermostat in the plug end of the cord. This will prevent operation of the engine coolant heater when the temperature is at or above 0°F (−18°C) as noted on the cord. 114 To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The engine coolant heater cord is located near the air cleaner box on the passenger side of the engine compartment. See Engine Compartment Overview on page 264 for more information on location. 3. Plug the cord into a normal, grounded 110-volt AC outlet. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you do not, it could be damaged. How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your retailer in the area where you will be parking your vehicle. The dealer/retailer can give you the best advice for that particular area. {CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ﬁre. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 115 Automatic Transaxle Operation The shift lever is located on the console between the seats. There are several different positions for the automatic transaxle. PARK (P): This position locks the front wheels. It is the best position to use when you start the engine because your vehicle cannot move easily. {CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). See Shifting Into PARK (P) on page 120. 116 Make sure the shift lever is fully in PARK (P) before starting the engine. Your vehicle has an automatic transaxle shift lock control system. You have to fully apply the regular brakes ﬁrst and then press the shift lever button before shifting from PARK (P) while the ignition key is in RUN. If you cannot shift out of PARK (P), ease pressure on the shift lever and push the shift lever all the way into PARK (P) while maintaining brake application. Then press the shift lever button and move the shift lever into another gear. See Shifting Out of PARK (P) on page 122. REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transaxle, see If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 241. NEUTRAL (N): In this position, the engine does not connect with the wheels. To restart the engine while your vehicle is already moving, use NEUTRAL (N) only. Also, use NEUTRAL (N) when your vehicle is being towed. {CAUTION: Shifting into a drive gear while the engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed. Notice: Shifting out of PARK (P) or NEUTRAL (N) while the engine is running at high speed may damage the transaxle. The repairs would not be covered by your warranty. Be sure the engine is not running at high speeds when shifting your vehicle. 117 DRIVE (D): This position is for normal driving with the automatic transaxle. It provides the best fuel economy for your vehicle. If you need more power for passing, and you are: (cid:129) Going less than about 35 mph (55 km/h), push the accelerator pedal about halfway down. (cid:129) Going above 35 mph (55 km/h), push the accelerator all the way down. Downshifting the transaxle in slippery road conditions could result in skidding, see “Skidding” under Loss of Control on page 226. INTERMEDIATE (I): This position is also used for normal driving. However, it reduces vehicle speed without using your brakes for slight downgrades where the vehicle would otherwise accelerate due to the steepness of the grade. If constant upshifting or downshifting occurs while driving up steep hills, this position can be used to prevent repetitive types of shifts. You might choose INTERMEDIATE (I) instead of DRIVE (D) when driving on hilly, winding roads, so that there is less shifting between gears. 118 The engine will not Auto Stop when the shifter is in INTERMEDIATE (I). See Starting the Engine (Automatic Engine Start/Stop) on page 110 for more information. LOW (L): This position reduces vehicle speed more than INTERMEDIATE (I) without actually using the brakes. It can be used on very steep hills, or in deep snow or mud. If the shift lever is put in LOW (L), the transaxle will not shift into LOW (L) until the vehicle is going slowly enough. The engine will not Auto Stop when the shifter is in LOW (L). See Starting the Engine (Automatic Engine Start/Stop) on page 110 for more information. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transaxle. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes, or parking brake to hold the vehicle in place. Parking Brake To set the parking brake, push down the parking brake pedal with your left foot. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 168. To release the parking brake, hold the regular brake pedal down with your right foot. Push down momentarily on the parking brake pedal with your left foot until you feel the pedal release. If the parking brake is not released when you begin to drive, the brake system warning light will be on and a chime will sound warning you that the parking brake is still on. The PUSH PARK PEDAL message will also appear in the Driver Information Center (DIC) to remind you to release the parking brake. See DIC Warnings and Messages on page 182. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before driving. Regenerative Braking Your vehicle has a regenerative braking system. Regenerative braking takes some of the energy from the moving vehicle and turns it back into electrical energy. This energy is then stored back into the vehicle’s hybrid battery system, contributing to increased fuel efficiency. The system works whenever you take your foot off the accelerator pedal while your vehicle is moving in a forward gear. This causes your vehicle to slow down slightly faster. It may feel like the brake pedal is being pressed, even when it is not. 119 Shifting Into PARK (P) {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. 1. Hold the brake pedal down with your right foot and set the parking brake. 2. Move the shift lever into PARK (P) by pressing the button on the shift lever while pushing the shift lever all the way toward the front of the vehicle. 3. Turn the ignition key to OFF. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). 120 Leaving Your Vehicle With the Engine Running {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Do not leave your vehicle with the engine running. If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and the parking brake is ﬁrmly set before leaving it. After moving the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ﬁrst pushing the shift lever button. If you can, it means that the shift lever was not fully locked in PARK (P). Torque Lock If you are parking on a hill and you do not shift the transaxle into PARK (P) properly, the weight of the vehicle can put too much force on the parking pawl in the transaxle. It could be difficult to pull the shift lever out of PARK (P). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see Shifting Into PARK (P) on page 120. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you might need to have another vehicle push your vehicle a little uphill to take some of the pressure from the parking pawl in the transaxle, this should let you pull the shift lever out of PARK (P). 121 Shifting Out of PARK (P) Your vehicle has an automatic transaxle shift lock control system. To shift out of PARK (P): 1. Apply the regular brake pedal. 2. Then press the shift lever button. 3. Move the shift lever to the desired gear. If you are still unable to shift out of PARK (P): 1. Fully release the shift lever button. 2. While holding down the brake pedal, press the shift lever button again. 3. Move the shift lever to the desired gear. If you still cannot move the shift lever from PARK (P), consult your dealer/retailer. 122 Parking Over Things That Burn {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:129) The exhaust system sounds strange or different. (cid:129) Your vehicle gets rusty underneath. (cid:129) Your vehicle was damaged in a collision. CAUTION: (Continued) (cid:129) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:129) Repairs were not done correctly. (cid:129) Your vehicle or the exhaust system has been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:129) Drive it only with all the windows down to blow out any CO; and (cid:129) Have your vehicle ﬁxed immediately. CAUTION: (Continued) 123 {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 123. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 237. Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: There is something about your vehicle that can make it move suddenly, and you or others can be seriously injured. This can happen if the vehicle is in the Auto Stop mode, and the shift lever is in DRIVE (D). Because your vehicle has the Automatic Engine Start/Stop feature, your vehicle’s engine might seem to be shut off when you come to a complete stop. However, if you then start to exit the vehicle, as soon as you take your foot off the brake pedal, the engine will start again and the vehicle can move forward. If you are going to exit your vehicle, ﬁrst shift to PARK (P) and turn the ignition to LOCK. Then exit. 124 {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set the parking brake and move the shift lever to PARK (P). Follow the proper steps to be sure your vehicle will not move. See Shifting Into PARK (P) on page 120. Mirrors Manual Rearview Mirror When you are sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Hold the mirror in the center to move it up or down and side to side. The day/night adjustment allows you to adjust the mirror to avoid glare from the lamps behind you. Push the tab forward for daytime use and pull it for nighttime use. Manual Rearview Mirror with OnStar® When you are sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Hold the mirror in the center to move it up or down and side to side. The day/night adjustment allows you to adjust the mirror to avoid glare from the lamps behind you. Push the tab forward for daytime use and pull it for nighttime use. There are also OnStar® buttons located at the bottom of the mirror face. See your dealer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 127 for more information about the services OnStar® provides. 125 Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror housing. Outside Power Mirrors The controls for the outside power mirrors are located on the inside of the vehicle near the driver’s side mirror. Use the selector switch located above the four-way control panel to choose either the left or right outside mirror. Then press the control pad to move the selected mirror in the desired direction. Adjust each mirror so you can see the side of your vehicle and the area beside and behind your vehicle. Heated Outside Mirrors If your vehicle has this feature, the surface of the outside mirrors will heat when the rear window defogger is activated. See “Rear Window Defogger” under Automatic Climate Control System on page 154 for more information. 126 OnStar® System OnStar® uses several innovative technologies and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar® Emergency advisors who can request emergency services be sent to your location. If you lock your keys in the vehicle, call OnStar® at 1-888-4-ONSTAR and they can send a signal to unlock your doors. If you need roadside assistance, press the OnStar® button and they can contact Roadside Service for you. OnStar® service is provided to you subject to the OnStar® Terms and Conditions. You may cancel your OnStar® service at any time by contacting OnStar®. A complete OnStar® Owner’s Guide and the OnStar® Terms and Conditions are included in the vehicle’s OnStar® Subscriber glove box literature. For more information, visit onstar.com or onstar.ca, contact OnStar® at 1-888-4-ONSTAR (1-888-466-7827) or TTY 1-877-248-2080, or press the OnStar® button to speak with an OnStar® advisor 24 hours a day, 7 days a week. Not all OnStar® features are available on all vehicles. To check if your vehicle is equipped to provide the services described below, or for a full description of OnStar® services and system limitations, see the OnStar® Owner’s Guide in your glove box or visit onstar.com. OnStar® Services For new vehicles with OnStar®, the Safe & Sound Plan, or the Directions & Connections® Plan is included for one year from the date of purchase. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions & Connections® Plan. For more information, press the OnStar® button to speak with an advisor. Some OnStar® services (such as Remote Door Unlock or Stolen Vehicle Location Assistance) may not be available until you register with OnStar®. 127 Available Services with Safe & Sound® Plan (cid:129) Automatic Notiﬁcation of Airbag Deployment (cid:129) Advanced Automatic Crash Notiﬁcation (AACN) (If equipped) Link to Emergency Services (cid:129) Roadside Assistance (cid:129) Stolen Vehicle Location Assistance (cid:129) AccidentAssist (cid:129) Remote Door Unlock/Vehicle Alert (cid:129) OnStar® Vehicle Diagnostics (cid:129) GM Goodwrench® On Demand Diagnostics (cid:129) OnStar® Hands-Free Calling with 30 complimentary minutes (cid:129) OnStar® Virtual Advisor (U.S. Only) Available Services included with Directions & Connections® Plan (cid:129) All Safe and Sound Plan Services (cid:129) Driving Directions - Advisor delivered or OnStar® Turn-by-Turn Navigation (If equipped) (cid:129) RideAssist Information and Convenience Services OnStar® Hands-Free Calling OnStar® Hands-Free Calling allows eligible OnStar® subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar® Pre-Paid Minute Packages. Hands-Free Calling may also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility. To ﬁnd out more, refer to the OnStar® Owner’s Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak with an OnStar® advisor by pressing the OnStar® button or calling 1-888-4-ONSTAR (1-888-466-7827). 128 (cid:129) (cid:129) OnStar® Virtual Advisor OnStar® Virtual Advisor is a feature of OnStar® Hands-Free Calling that uses your minutes to access location-based weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. See the OnStar® Owner’s Guide for more information (Only available in the continental U.S.). OnStar® Steering Wheel Controls Your vehicle may have a Talk/Mute button that can be used to interact with OnStar® Hands-Free Calling. See Audio Steering Wheel Controls on page 206 for more information. On some vehicles, you may have to hold the button for a few seconds and give the command “ONSTAR” in order to activate the OnStar® Hands-Free Calling feature. On some vehicles, the mute button can be used to dial numbers into voicemail systems, or to dial phone extensions. See the OnStar® Owner’s Guide for more information. How OnStar® Service Works In order to provide you with OnStar® services, your vehicle’s OnStar® system has the capability of recording and transmitting vehicle information. This information is automatically sent to an OnStar® Call Center at the time of an OnStar® button press, Emergency button press or if your airbags or AACN system deploys. The vehicle information usually includes your GPS location and, in the event of a crash, additional information regarding the accident that your vehicle has been involved in (e.g. the direction from which your vehicle was hit). When you use the Virtual Advisor feature of OnStar® Hands-Free Calling, your vehicle also sends OnStar® your GPS location so that we can provide you with location-based services. 129 OnStar® service cannot work unless your vehicle is in a place where OnStar® has an agreement with a wireless service provider for service in that area. OnStar® service also cannot work unless you are in a place where the wireless service provider OnStar® has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar® service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times. OnStar® service that involves location information about your vehicle cannot work unless GPS satellite signals are unobstructed and available in that place as well. Your vehicle must have a working electrical system (including adequate battery power) for the OnStar® equipment to operate. There are other problems OnStar® cannot control that may prevent OnStar® from providing OnStar® service to you at any particular time or place. Some examples are damage to important parts of your vehicle in an accident, hills, tall buildings, tunnels, weather or wireless phone network congestion. Your Responsibility You may need to increase the volume of your radio to hear the OnStar® advisor. If the light next to the OnStar® buttons is red, this means that your system is not functioning properly and should be checked by your dealer/retailer. If the light appears clear (no light is appearing), your OnStar® subscription has expired. You can always press the OnStar® button to conﬁrm that your OnStar® equipment is active. 130 Storage Areas Cupholder(s) Glove Box Open the glove box by lifting up on the lever. Close the glove box with a ﬁrm push. There are two removable cupholders and additional storage areas located at the rear of the shift lever. To access, push the button and the cover will slide back automatically. To close, slide the cover forward and lock into place. 131 Center Console Storage Area Your vehicle has a center console with two storage areas. To access the upper tray storage, lift the passenger side lever. To access the lower storage area, lift the driver side lever. Convenience Net Your vehicle may have a convenience net located on each side of the trunk to help keep small loads, like grocery bags, in place during sharp turns or quick stops and starts. The net is not designed for larger, heavier items. Pull down the door on the back of the center console to use the rear seat cupholders. 132 A deﬂector will automatically raise when the sunroof is opened. The deﬂector will retract when the sunroof is closed. To close the sunroof, press the front of the switch and hold it until the sunroof is closed. The sunroof will stop if the switch is released. Close the sunshade by hand. The sunroof glass panel cannot be opened or closed if the vehicle has an electrical failure. Notice: the sliding glass panel, damage will occur and the sunroof may not open or close properly. Always close the glass panel before closing the sunshade. If you force the sunshade forward of Sunroof If your vehicle has a sunroof, the switch is located on the headliner between the map lamps. The sunroof will only operate while the ignition is in ON or in ACC, or if Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 109. Press the back of the switch and release it to open the sunroof to the vent position. From the vent position, press and release the back of the switch to express-open the sunroof. To stop the sunroof from express opening, press the switch again. If the sunshade is closed, it will open automatically when the sunroof opens past the vented position. 133 ✍ NOTES 134 Section 3 Instrument Panel Instrument Panel Overview ........................ 138 Hazard Warning Flashers .......................... 140 Other Warning Devices ............................. 140 Horn .......................................................... 140 Tilt and Telescopic Steering Wheel ............ 140 Turn Signal/Multifunction Lever .................. 141 Turn and Lane-Change Signals ................. 142 Headlamp High/Low-Beam Changer .......... 142 Flash-to-Pass ............................................ 142 Windshield Wipers ..................................... 143 Windshield Washer .................................... 144 Cruise Control ........................................... 145 Headlamps ................................................ 148 Headlamps on Reminder ........................... 148 Headlamps Off in PARK (P) ...................... 149 Delayed Headlamps .................................. 149 Daytime Running Lamps (DRL) ................. 149 Automatic Headlamp System ..................... 150 Instrument Panel Brightness ...................... 151 Dome Lamp .............................................. 151 Entry/Exit Lighting ...................................... 151 Parade Dimming ........................................ 152 Overhead Console Reading Lamps ........... 152 Trunk Lamp ............................................... 152 Battery Run-Down Protection ..................... 152 Accessory Power Outlet(s) ........................ 153 Climate Controls ......................................... 154 Automatic Climate Control System ............. 154 Outlet Adjustment ...................................... 160 Warning Lights, Gages, and Indicators ..... 161 Instrument Panel Cluster ........................... 162 Speedometer and Odometer ...................... 163 Trip Odometer ........................................... 163 Tachometer ............................................... 163 Safety Belt Reminder Light ........................ 163 Passenger Safety Belt Reminder Light ....... 164 Airbag Readiness Light ............................. 164 Passenger Airbag Status Indicator ............. 165 Charging System Light .............................. 167 Brake System Warning Light ..................... 168 Antilock Brake System Warning Light ........ 169 Low Tire Pressure Warning Light .............. 170 Traction Control System (TCS) Warning Light ........................................ 170 Electronic Stability Control Indicator Light ........................................ 171 135 Section 3 Instrument Panel Engine Coolant Temperature Warning Light ........................................ 171 Malfunction Indicator Lamp ........................ 172 Oil Pressure Light ..................................... 175 Security Light ............................................ 176 Cruise Control Light .................................. 176 Highbeam On Light ................................... 176 Fuel Gage ................................................. 177 Auto Stop Mode ........................................ 178 Charge/Assist Gage ................................... 178 Fuel Economy Light .................................. 179 Driver Information Center (DIC) .................. 179 DIC Operation and Displays ...................... 180 DIC Warnings and Messages .................... 182 DIC Vehicle Personalization ....................... 187 Audio System(s) ......................................... 192 Setting the Time ........................................ 194 Radio with CD (MP3) ................................ 195 Using an MP3 ........................................... 200 Theft-Deterrent Feature ............................. 206 Audio Steering Wheel Controls .................. 206 Radio Reception ........................................ 207 Care of Your CDs ..................................... 207 Care of the CD Player .............................. 207 Backglass Antenna .................................... 208 136 ✍ NOTES 137 Instrument Panel Overview 138 The main components of your instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 160. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 141. C. Instrument Panel Cluster. See Instrument Panel Cluster on page 162. J. Horn. See Horn on page 140. K. Audio Steering Wheel Controls (If Equipped). See Audio Steering Wheel Controls on page 206. L. Ignition Switch. See Ignition Positions on page 108. D. Windshield Wiper and Washer Lever. See Windshield Wipers on page 143 and Windshield Washer on page 144. M. Automatic Climate Control System. See Automatic Climate Control System on page 154. E. Hazard Warning Flashers Button. See Hazard Warning Flashers on page 140. F. Passenger Airbag Status Indicator. See Passenger Airbag Status Indicator on page 165. G. Instrument Panel Brightness Control. See Instrument Panel Brightness on page 151. H. Cruise Controls. See Cruise Control on page 145. Driver Information Center (DIC) Buttons. See Driver Information Center (DIC) on page 179. I. Tilt Lever. See Tilt and Telescopic Steering Wheel on page 140. N. Traction Control Button. See Traction Control System (TCS) on page 217. Electronic Stability Control Button. See Electronic Stability Control on page 219. O. Shift Lever. See Automatic Transaxle Operation on page 116. P. Audio System. See Audio System(s) on page 192. Q. Glove Box. See Glove Box on page 131. 139 Hazard Warning Flashers The hazard warning ﬂashers let you warn the police and others that you have a problem. The front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located towards the center of the instrument panel. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. While the hazard warning ﬂashers are on, the turn signals do not work. The hazard warning ﬂashers work no matter what position the key is in, and even if the key is not in the ignition switch. Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. Horn Press near or on the horn symbols on the steering wheel pad to sound the horn. Tilt and Telescopic Steering Wheel A tilt and telescope wheel lets you adjust the steering wheel before you drive. The steering wheel can be raised to the highest level to give your legs more room when you enter and exit the vehicle. The lever that lets you tilt and telescope the steering wheel is located on the left side of the steering column. 140 To tilt and telescope the steering wheel, pull down the lever. Then move the steering wheel up or down or backward or forward into a comfortable position. Pull the lever up to lock the steering wheel in place. Do not adjust the tilt and telescope lever while driving. Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: (cid:129) G Turn and Lane-Change Signals. See Turn and Lane-Change Signals on page 142. (cid:129) 53 Headlamp High/Low-Beam Changer. See Headlamp High/Low-Beam Changer on page 142. (cid:129) Flash-to-Pass. See Flash-to-Pass on (cid:129) O Exterior Lamp Control. See Headlamps on page 142. page 148. 141 Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions let you signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever returns automatically to the normal position. An arrow on the instrument panel cluster ﬂashes in the direction of the turn or lane change. To signal a lane change, raise or lower the lever until the arrow starts to ﬂash. Hold it there until you complete your lane change. The lever returns by itself when it is released. If the arrows ﬂash rapidly or do not go on at all as you signal a turn or lane change, a signal bulb could be burned out and other drivers will not see your turn signal. Replace burned out bulbs to help avoid an accident. Also, check the appropriate fuses. See Fuses on page 343. 142 Headlamp High/Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal/multifunction lever toward the front of the vehicle. This light on the instrument panel cluster comes on if the high beam lamps are turned on while the ignition is on. To change the headlamps from high beam to low beam, pull the turn signal lever toward the rear of the vehicle. Flash-to-Pass This feature lets you use your high-beam headlamps to signal a driver in front of you that you want to pass. To use it, pull the turn signal/multifunction lever toward you until the high-beam headlamps come on, then release the lever to turn them off. Windshield Wipers Use this lever, located on the right side of the steering wheel, to operate the windshield wipers. 9(Off): Move the lever to this position to turn off the windshield wipers. &(Intermittent; Speed Sensitive Wipers): Move the lever to this position for intermittent or speed sensitive operation. The amount of delay time varies between wiping cycles due to the delay setting selected or the speed of the vehicle. x(Delay): While the lever is in the intermittent position, turn the intermittent adjust band with this symbol on it up or down to select a shorter or longer delay between wiping cycles. To the left of the adjust band are bars, increasing in size from bottom to top, that indicate the frequency of the wipes. Smaller bars mean the wipers movement is less frequent. Larger bars mean the movement is more frequent. 6 (Low Speed): Move the lever up to the ﬁrst setting past intermittent, for steady wiping at low speed. 1 (High Speed): Move the lever up to the second setting past intermittent, for wiping at a high speed. 8(Mist): Move the lever all the way down to this position for a single wiping cycle. Hold it there until the windshield wipers start; then let go. The windshield wipers stop after one wiping cycle. If additional wiping cycles are needed, hold the lever down longer. 143 Damaged wiper blades can prevent you from seeing well enough to drive safely. Clear ice and snow from the wiper blades before using them to prevent damage. If the wiper blades are frozen to the windshield, carefully loosen or thaw them. If your blades do become damaged, get new blades. Heavy snow or ice can overload the wiper motor. A circuit breaker stops the motor until it cools. Clear away snow or ice to prevent an overload. If the motor gets stuck, turn the wipers off, clear away the snow or ice, and then turn the wipers back on. As an added safety feature, if the wipers are on for more than 15 seconds, the vehicle’s headlamps turn on automatically. They turn off 15 seconds after the wipers are turned off. Windshield Washer To wash the windshield, press the button at the end of the lever until the washers begin. {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. When the button is released, the washers stop, but the wipers continue to wipe about three times or resume the previous speed. 144 Cruise Control Cruise control lets you maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below 25 mph (40 km/h). {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads. Setting Cruise Control {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. The cruise control buttons are located on the steering wheel. I (On/Off): Press I to turn the cruise control system on and off. 145 RES+ (Resume): Press RES+ to resume a set speed and to accelerate the speed. SET− (Set): Press SET– to set a speed and to decrease the speed. To set a speed do the following: 1. Press I to turn cruise control on. The indicator light on the button comes on. 2. Get up to the desired speed. 3. Press the SET− and release it. The cruise symbol displays in the instrument panel cluster to show the system is engaged. 4. Take your foot off the accelerator pedal. When the brakes are applied, the cruise control shuts off. If the vehicle is in cruise control and the Traction Control System (TCS) begins to limit wheel spin, the cruise control automatically disengages. See Traction Control System (TCS) on page 217. When road conditions allow, the cruise control can be used again. Resuming a Set Speed Suppose you set the cruise control at a desired speed and then apply the brakes. This disengages the cruise control. The cruise symbol in the instrument panel cluster also goes out indicating cruise is no longer engaged. To return to the previously set speed, you do not need to go through the set process again. Once the vehicle is at a speed of about 25 mph (40 km/h) or more, you can brieﬂy press the RES+. This takes the vehicle back up to the previously chosen speed and stays there. Increasing Speed While Using Cruise Control There are two ways to go to a higher speed. If the cruise control system is already engaged, press the RES+. Hold it there until you reach the desired speed, and then release the button. (cid:129) To increase the vehicle’s speed in very small amounts, brieﬂy press the RES+ and then release it. Each time this is done, the vehicle goes about 1 mph (1.6 km/h) faster. 146 (cid:129) When the brakes are applied this turns off the cruise control. Many drivers ﬁnd this to be too much trouble and do not use cruise control on steep hills. Ending Cruise Control There are two ways to disengage the cruise control: (cid:129) Step lightly on the brake pedal; when cruise control disengages, the cruise symbol in the instrument panel cluster goes out. (cid:129) Press the on/off button, to turn off the cruise control system. Erasing Speed Memory The cruise control set speed memory is erased, when the cruise control or the ignition is turned off. Reducing Speed While Using Cruise Control If the cruise control system is already engaged: (cid:129) Push and hold the SET− until the desired lower speed is reached, then release it. (cid:129) To slow down in very small amounts, brieﬂy push the SET−. Each time this is done, the vehicle goes about 1 mph (1.6 km/h) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase the vehicle’s speed. When you take your foot off the pedal, the vehicle slows down to the previous cruise control speed that was set earlier. Using Cruise Control on Hills How well your cruise control works on hills depends upon the vehicle’s speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle’s speed. When going downhill, you might have to brake or shift to a lower gear to keep the vehicle at a lower speed. 147 Headlamps The band on the lever on the outboard side of the steering column operates the exterior lamps. The exterior lamp control has the following four positions: 2(Headlamps): Turn the band to this position to turn on the headlamps, parking lamps, and taillamps. ;(Parking Lamps): Turn the band to this position to turn on the parking lamps and taillamps only. 148 AUTO (Automatic Headlamp System): Turn the band to this position to automatically turn on the Daytime Running Lamps during daytime, and the headlamps, parking lamps, and taillamps at night. P(Off/On): Turn the band to this position to turn on the Automatic Headlamp System. In Canada, this position only works when a vehicle is in the PARK (P) position. To turn on the Automatic Headlamp System, turn the switch to off/on. To turn them off, turn the switch to off/on again. This is a momentary control switch that springs back when released. The Automatic Headlamp System always turns on at the beginning of an ignition cycle. Headlamps on Reminder If you open the driver’s door and turn off the ignition while leaving the lamps on, you will hear a warning chime. Headlamps Off in PARK (P) This feature works when the ignition is ON and it is dark outside. To turn the headlamps off when it is dark outside but keep other exterior lights on, turn the exterior lamp control to the parking lamp position. In this position, the parking lamps, sidemarker lamps, taillamps, license plate lamps and instrument panel lights are on, but the headlamps are off. To turn on the headlamps along with the other lamps when it is dark outside, turn the exterior lamp control to the AUTO or headlamp position. This feature will not work for Canadian vehicles. Delayed Headlamps The delayed headlamps feature keeps the headlamps on for 20 seconds after the key is turned to OFF, then the headlamps automatically turn off. To override the 20 second delayed headlamp feature while it is active turn the turn signal/multifunction lever up one position and then back to AUTO. Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL are helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional DRL are required on all vehicles ﬁrst sold in Canada. The vehicle has a light sensor on top of the instrument panel that controls the DRL. Make sure it is not covered, or the head lamps will be on when they are not needed. The DRL system makes the low-beam headlamps come on at a reduced brightness when the following conditions are met: (cid:129) The ignition is on. (cid:129) The exterior lamps control is in AUTO. (cid:129) The exterior lamps control is in the parking lamps only position (This applies only to vehicles that are ﬁrst sold in Canada). (cid:129) The light sensor detects daytime light. (cid:129) The parking brake is released or the vehicle is not in PARK. 149 When the DRL system is on, the taillamps, sidemarker lamps, parking lamps, and instrument panel lights are not on unless you turn the exterior lamps control to the parking lamp position. As with any vehicle, you should turn on the regular headlamp system when they are needed. Automatic Headlamp System When it is dark enough outside, the automatic headlamp system turns on the headlamps at the normal brightness along with other lamps such as the taillamps, sidemarker, parking lamps, and the instrument panel lights. The radio lights will also be dim. Your vehicle has a light sensor on top of the instrument panel that controls the automatic headlamp system. Make sure it is not covered or the automatic headlamp system will be on when it is not needed. There is a delay in the transition between the daytime and nighttime operation of the DRL and the automatic headlamp systems so that driving under bridges or bright overhead street lights does not affect the system. The DRL 150 and automatic headlamp systems will only be affected when the light sensor sees a change in lighting lasting longer than this delay. If you start your vehicle in a dark garage, the automatic headlamp system comes on immediately. Once you leave the garage, it takes about one minute for the automatic headlamp system to change to DRL if it is light outside. During that delay, the instrument panel cluster may not be as bright as usual. Make sure the instrument panel brightness control is in the full bright position. See “Instrument Panel Brightness Control” under Instrument Panel Brightness on page 151. To idle your vehicle with the automatic headlamp system off, turn the ignition on and set the exterior light switch to the off/on position. For Canadian vehicles, the transmission must stay in PARK (P) for this function. As with any vehicle, you should turn on the regular headlamps when they are needed. Instrument Panel Brightness The control for this feature is located on the instrument panel to the left of the steering wheel. Turn the knob clockwise or counterclockwise to brighten or dim the lights. Dome Lamp Your vehicle might have a dome lamp without a switch. If the dome lamp has a switch, the following are the settings. 9(Off): Move the lever to this position to turn the lamp off, even when a door is open. 1(Door): Move the lever to this position so that the lamp comes on when a door is opened. +(On): Move the lever to this position to turn the dome lamp on. Entry/Exit Lighting The lamps inside the vehicle come on when any door is opened. These lamps fade out about 20 seconds after all of the doors have been closed or when the ignition is turned to ON. They also go on when you press the unlock symbol button or the horn symbol on the Remote Keyless Entry (RKE) system transmitter. The lamps inside the vehicle stay on for about 20 seconds after the key is removed from the ignition to provide light as you exit. 151 Battery Run-Down Protection Your vehicle has a battery run-down feature designed to protect the vehicle’s battery. When any interior lamp (trunk, reading lamps, or dome lamp) is left on when the ignition is turned off, the battery run-down protection system automatically shuts the lamp off after 20 minutes. This prevents draining of the battery. To reactivate the interior lamps, do one of the following: (cid:129) Open any door. (cid:129) Press any Remote Keyless Entry (RKE) transmitter button. (cid:129) Press the power door lock switch. (cid:129) Press the remote trunk release. (cid:129) Turn the lamp that was left on to off and then to on again. Parade Dimming Parade dimming is a separate lighting mode that comes on while the parking lamps are turned on during the day. It prevents the display lights and indicator lights from being dim, while the parking lamps are used during the day. Overhead Console Reading Lamps The vehicle may have reading lamps on the overhead console. These lamps come on when the doors are opened if the lamp switch is not in the OFF position. Press the side of each lamp to turn them on and off, while the doors are closed. Overhead Ambient Lighting These lamps will automatically turn on and off as controlled by the light sensor located on top of the instrument panel. Trunk Lamp The trunk lamp comes on when the trunk is open and turns off when it is closed. 152 Accessory Power Outlet(s) Accessory power outlets can be used to connect auxiliary electrical equipment such as a cellular telephone or CB radio. There are two accessory power outlets. One accessory power outlet is inside the center storage console and the other is located on the center storage console below the climate controls. To use an outlet, lift the protective cap. When not in use, always cover the outlet with the protective cap. The accessory power outlet is operational at all times. Notice: Leaving electrical equipment plugged in for an extended period of time while the vehicle is off will drain the battery. Power is always supplied to the outlets. Always unplug electrical equipment when not in use and do not plug in equipment that exceeds the maximum 20 ampere rating. Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your retailer for additional information on the accessory power outlet. Notice: Adding any electrical equipment to your vehicle can damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer/retailer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Notice: Improper use of the power outlet can cause damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. 153 The following are climate control settings that use more fuel: (cid:129) Normal air conditioning mode. (cid:129) The defrost mode. (cid:129) Extreme temperature settings, such as 60°F (15°C) / 90F (32°C). (cid:129) High fan speed settings. The following can help reduce fuel consumption: (cid:129) Use of the full automatic control method as described under Automatic Operation. (cid:129) Use hybrid air conditioning, instead of the normal air conditioning. (cid:129) Select a temperature setting that is higher in hot weather and lower in cold weather. (cid:129) Only use defrost to clear the windows. These suggestions will help to reduce fuel consumption, but may reduce overall comfort. Climate Controls Automatic Climate Control System You can automatically control the heating, cooling, and ventilation in your vehicle. Climate Control Inﬂuence on Hybrid Operation and Fuel Economy The climate control system is dependent upon other vehicle systems for heat and power input. Certain climate control settings can lead to higher fuel consumption and/or fewer Auto Stops. 154 Automatic Operation AUTO (Automatic): Select AUTO on both the fan speed knob and the air delivery mode knob to activate the automatic system. When automatic operation is active the system controls the inside temperature and air delivery. Use the steps below to place the entire system in full automatic control: 1. Turn the fan knob and the mode knob to the AUTO position. The current set temperature displays. When AUTO is selected, the air conditioning operation and air inlet is automatically controlled. The air conditioning compressor runs while the outside temperature is over about 40°F (4°C). The air inlet is normally set to outside air. If it is hot outside, the air inlet can automatically switch to recirculate inside air to help quickly cool down your vehicle. 2. Set the temperature. An initial setting of 73°F (23°C) is recommended. Allow about 20 minutes for the system to regulate. Press the w or x arrow temperature buttons to adjust the temperature setting as necessary. If the temperature is set at 60°F (15°C) the system remains at the maximum cooling setting. If the temperature is set at 90°F (32°C) the system remains at the maximum heat setting. Choosing either maximum setting does not cause the vehicle to heat or cool any faster. Be careful not to cover the sensor located on the top of the instrument panel near the windshield. This sensor regulates air temperature based on the intensity of the sun. Also do not cover the sensor grille on the lower right side of the climate control faceplate, as this regulates the inside temperature. To avoid blowing cold air at engine start-up in cold weather, the system delays turning on the fan until warm air is available. The length of delay depends on the engine coolant temperature. Turning the fan knob overrides this delay and changes the fan to the selected speed. 155 Manual Operation The air delivery mode or fan speed, can manually be adjusted. Fan Speed Knob 9(Off): Select this position to turn off the fan. Outside air still enters the vehicle. The direction can be changed by changing the mode position. The temperature can also be adjusted using either the up or down arrow temperature buttons. 9(Fan): Turn the knob with the fan symbol to manually adjust the fan speed. w x Temperature Control: Press the w and x arrows to increase or decrease the temperature inside the vehicle. Air Delivery Mode Knob H(Vent): Use this mode to direct air to the instrument panel outlets. )(Bi-Level): Use this mode to direct half of the air to the instrument panel outlets, and the remaining air to the ﬂoor outlets. 156 6(Floor): Use this mode to direct most of the air to the ﬂoor outlets with some air directed to the side window outlets. The right knob can also be used to select defog or defrost modes. Information on defogging and defrosting can be found later in this section. #(Normal Air Conditioning): Press this button to turn the air conditioning compressor on and off. A light above the button comes on while the air conditioning is on. When air conditioning is selected or is in AUTO mode, the system runs the air conditioning automatically to cool and dehumidify the air entering the vehicle. While in this mode, the hybrid system does not shut the engine down at complete stops. On hot days, open the windows long enough to let hot inside air escape. This reduces the time it takes for your vehicle to cool down. Then keep your windows closed for the air conditioner to work its best. On cool, but sunny days while using manual operation of the automatic system, use bi-level to deliver warm air to the ﬂoor and cooler air to the instrument panel outlets. To warm or cool the air delivered, press the temperature buttons to the desired setting. In AUTO mode the system cools and dehumidiﬁes the air inside the vehicle. Also while in AUTO mode, the system maximizes its performance by using recirculation as necessary. Heating: On cold days when using manual operation of the automatic system, use ﬂoor mode to deliver air to the ﬂoor outlets. To warm or cool the air delivered, push the temperature buttons to the desired setting. To use the automatic mode, turn the knob to AUTO and adjust the temperature by pressing the temperature buttons. When the heater is in use, there might be slight noise or vibration during Auto Stops. This is due to the coolant circulation pump that continues to circulate heat through the system during the engine Auto Stop. The heater works best if the windows are kept closed. h (Recirculation): Press the button to turn on the recirculation mode. The air inside the vehicle recirculates through the climate control system and the vehicle, not from outside your vehicle. This mode is helpful when trying to limit odors from entering the vehicle and for maximum air conditioning performance in hot weather. When the button is pressed, an indicator light above the button comes on. The recirculation indicator light blinks three times if recirculation is used in a mode in which it cannot function. Only use this mode when it is needed for comfort, since window fogging rapidly occurs if the air conditioning compressor is not engaged. Press this button to cancel the auto recirculation feature. Each time the vehicle is started, the system reverts to the auto recirculation function. If you select recirculation while in defrost, defog or ﬂoor, the light on the button ﬂashes three times and then goes out to indicate that this is not allowed. This is to prevent window fogging. 157 When the weather is cool or damp, operating the system in recirculation for extended periods of time can cause fogging of the vehicle’s windows. To clear the fog, select either defog or defrost. Make sure the air conditioning is on. Allow the air conditioning to run automatically to help dehumidify the air. N (Hybrid Air Conditioning): The hybrid A/C function tries to balance fuel economy and air conditioning comfort. When hybrid A/C is used in warm weather, your vehicle gets better fuel economy and/or more frequent autostops at the expense of cabin cooling performance compared to normal air conditioning. Maximum Air Conditioning On hot days, open the windows to let hot inside air escape; then close them. This helps to reduce the time it takes for your vehicle to cool down. It also helps the system to operate more efficiently. For quick cool down on hot days, do the following: 1. Select the C vent mode. 2. Select the highest fan speed. 3. Select # air conditioning. 4. Select the h recirculation mode. 5. Select the coolest temperature. Using these settings together for long periods of time may cause the air inside of your vehicle to become too dry. To prevent this from happening, after the air in your vehicle has cooled, turn the recirculation mode off. 158 Defogging and Defrosting Fog on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to choose from to clear fog or frost from the windshield. Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. -(Defog): Turn the mode knob to this position to select the defog setting, which delivers air to the ﬂoor and windshield outlets. Use this setting to clear the windows of fog or moisture. 0(Defrost): Turn the mode knob to this position to defrost the windshield. The system automatically controls the fan speed if defrost is selected from the AUTO mode. If the outside temperature is 40°F (4°C) or warmer, the air conditioning compressor automatically runs to help dehumidify the air and dry the windshield. The air conditioning indicator light blinks three times if the compressor is turned off while in this mode. The engine will not perform Auto Stops when the defrost mode is on. Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. <(Rear): Press this button to turn the rear window defogger on or off. An indicator light above the button comes on to show that the rear window defogger is activated. If driving below 50 mph (80 km/h), the rear window defogger turns off about 15 minutes after the button is pressed. If additional warming time is needed, press the button again. If the vehicle’s speed is maintained above 50 mph (80 km/h), the rear window defogger remains on once the button is pressed. If your vehicle has heated outside mirrors, the surface of the outside mirrors also heat when the rear window defogger is activated. See Outside Power Mirrors on page 126. Notice: Do not use a razor blade or sharp object to clear the inside rear window. Do not adhere anything to the defogger grid lines in the rear glass. These actions may damage the rear defogger. Repairs would not be covered by your warranty. 159 Operation Tips (cid:129) Clear away any ice, snow, or leaves from the air inlets at the base of the windshield that can block the ﬂow of air into your vehicle. (cid:129) Do not use non-GM approved hood deﬂectors as they could adversely affect the performance of the system. (cid:129) Keep the path under the front seats clear of objects to help circulate the air inside of your vehicle more effectively. (cid:129) When an objectionable odor outside the vehicle is encountered, use the recirculation mode, with the temperature knob at a comfortable setting to prevent the odor from entering the vehicle through the ventilation system. This can be helpful when driving through a long tunnel with poor ventilation. However, extended usage of this mode in cold or cool weather can cause window fogging. Outlet Adjustment There are four main air outlets on the instrument panel. Use the lever located in the center of each outlet by moving it either side-to-side or up and down, to change the direction and amount of airﬂow in the vehicle. The center thumbwheel does not control the main outlets. Dedicated Rear Seat Air Outlet For vehicles with this feature, the dedicated rear seat air outlet is located in the center of the instrument panel above the two main center outlets. This outlet is aimed to provide comfort to the rear seat passengers, especially while using air conditioning in warm weather. Use the thumbwheel in the center of the outlet to turn the airﬂow on or off. This can be adjusted to improve front seat passenger comfort if there are no rear seat passengers. The direction of airﬂow cannot be adjusted since it is directed towards the rear seat passengers. Do not attempt to move the horizontal vent vane, as breakage can occur. 160 Warning Lights, Gages, and Indicators This part describes the warning lights and gages on your vehicle. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As the details show on the next few pages, some warning lights come on brieﬂy when you start the engine just to let you know they are working. If you are familiar with this section, you should not be alarmed when this happens. Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there is a problem with your vehicle. When one of the warning lights comes on and stays on as you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual’s advice. Waiting to do repairs can be costly and even dangerous. So please get to know your vehicle’s warning lights and gages. They can be a big help. 161 Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, how much fuel you are using, and many other things you will need to drive safely and economically. Your vehicle has this instrument panel cluster, which includes indicator warning lights and gages that are explained on the following pages. United States version shown, Canada Similar 162 Speedometer and Odometer Your speedometer lets you see your speed in miles per hour (mph) or kilometers per hour (km/h). See DIC Vehicle Personalization on page 187 for more information. Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). Your vehicle has a tamper resistant odometer. The digital odometer will read 999,999 if someone tries to turn it back. You may wonder what happens if your vehicle needs a new odometer installed. If the new one can be set to the mileage total of the old odometer, then it must be. But if it can’t, then it is set at zero and a label must be put on the driver’s door to show the old mileage reading when the new odometer was installed. Trip Odometer The trip odometer can tell you how far you have driven since you last reset it. The trip odometer is accessed and reset through the Driver Information Center (DIC). See DIC Operation and Displays on page 180 for more information. Tachometer Your tachometer displays the engine speed in revolutions per minute (rpm). Your vehicle has auto stop and the indicator for this is on the tachometer. For more information see Auto Stop Mode on page 178. Safety Belt Reminder Light When the key is turned to ON or START, a chime will come on for several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is already buckled. The safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more. This chime and light is repeated if the driver remains unbuckled and the vehicle is in motion. If the driver’s belt is already buckled, neither the chime nor the light will come on. 163 Passenger Safety Belt Reminder Light Several seconds after the key is turned to ON or START, a chime will sound for several seconds to remind the front passenger to buckle their safety belt. This would only occur if the passenger airbag is enabled. See Passenger Sensing System on page 77 for more information. The passenger safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more. Airbag Readiness Light There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 67. This chime and light are repeated if the passenger remains unbuckled and the vehicle is in motion. This light will come on when you start your vehicle, and it will ﬂash for a few seconds. Then the light should go out. This means the system is ready. If the passenger’s safety belt is buckled, neither the chime nor the light will come on. If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away. 164 {CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle. The airbag readiness light should ﬂash for a few seconds when you turn the ignition key to ON. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. Passenger Airbag Status Indicator Your vehicle has the passenger sensing system. Your instrument panel has a passenger airbag status indicator. United States Canada When the ignition key is turned to ON or START, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger’s frontal airbag and seat-mounted side impact airbag. 165 If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger’s frontal airbag and seat-mounted side impact airbag are enabled (may inﬂate). Your vehicle has a rear seat that will accommodate a rear-facing child restraint. A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. {CAUTION: {CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag and seat-mounted side impact airbag. A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating airbag. Do not use a rear-facing child restraint in the right front passenger’s seat if the airbag is turned on. Even though the passenger sensing system is designed to turn off the passenger’s frontal airbag and seat-mounted side impact airbag if the system detects a rear-facing child restraint, no system is fail-safe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. We recommend that rear-facing child restraints be secured in the rear seat, even if the airbag is off. 166 If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger’s frontal airbag and seat-mounted side impact airbag. See Passenger Sensing System on page 77 for more on this, including important safety information. If, after several seconds, all status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your retailer for service. {CAUTION: If the off indicator and the airbag readiness light ever come on together, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger seat may not have the protection of the airbags. See Airbag Readiness Light on page 164. Charging System Light The charging system light will come on for a few seconds when you turn on the ignition as a check to indicate it is working. If the light stays on, or comes on while you are driving and you hear a chime, there could be a problem with the electrical charging system. This could indicate that there is a loose generator drive belt or another electrical problem. Have it checked right away. Driving while this light is on could drain the battery and result in the engine and headlights suddenly shutting off. If you must drive a short distance with this light on, turn off accessories, such as the radio, air conditioner and heater fan. 167 When the ignition is on, the brake system warning light will also come on when you set your parking brake. The light will stay on if your parking brake does not release fully. If it stays on after your parking brake is fully released, it means you have a brake problem. The Driver Information Center (DIC) may display a BRAKE FLUID message. See DIC Warnings and Messages on page 182 for more information. If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push or the pedal may go closer to the ﬂoor. It may take longer to stop. Try turning off and restarting the vehicle one or two times, if the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 247. Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on, there is a brake problem. Have your brake system inspected right away. United States Canada This light should come on brieﬂy when you turn the ignition key to ON. If it does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. 168 {CAUTION: Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident. If the light is still on after you have pulled off the road and stopped carefully, have

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2007 Saturn AURA Hybrid Owners Manual