2006 Saab 9 3 Owners Manual

tires or wheels. See “When It Is Time for New Tires” on page 259 and “Wheel Replacement” on page 262 for more infor- mation. The purpose of regular rotation is to achieve more uniform wear for all tires on the vehi- cle. The first rotation is the most important. When rotating your tires, always use the correct rotation pattern. Left front tire to left rear. Left rear tire to right front. Right front to right rear. Right rear to left front. Don’t include the compact spare tire in your tire rotation.

93U SM 06.book Page 259 Friday, February 18, 2005 1:15 PM

Flat spotting All tires get hot, especially on long journeys or when the car is driven hard. After the car has been parked with hot tires and the tires have cooled down, a flat spot can form in the tire, where it is in contact with the ground. The same can occur if the car has not been moved for a long time. Flat spots can cause vibration that can be felt through the steering wheel, similar to that experienced when the wheels need bal- ancing. Flat spots of this type disappear once the tires get hot again, usually after 10–15 miles (20–25 km) of driving at cruising speed. If the outdoor temperature is low it takes a longer distance.

When It Is Time for New Tires One way to tell when it’s time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. You need a new tire if any of the following statements are true: (cid:127) You can see the indicators at three or

more places around the tire.

(cid:127) You can see cord or fabric showing

through the tire’s rubber.

(cid:127) The tread or sidewall is cracked, cut or snagged deep enough to show cord or fabric.

(cid:127) The tire has a bump, bulge or split. (cid:127) The tire has a puncture, cut or other damage that can’t be repaired well because of the size or location of the damage.

Car care

259

Treadwear indicator

Treadwear indicators The tires incorporate wear indicators in the form of smooth, treadless strips across the width, which become visible when only 2/32" (1.6 mm) of tread remains. As soon as the indicators become visible, new tires should be fitted without delay. Make sure you are familiar with the legal limit for minimum tread depth in your country and also any regulations gov- erning the use of winter (snow) tires.

93U SM 06.book Page 260 Friday, February 18, 2005 1:15 PM

260

Car care

Buying New Tires To find out what kind and size of tires you need, look at the Tire-Loading Information label. If you wish to fit other tires or wheels than those supplied with the car, consult your Saab dealer first as to the possibilities available. Wheels/tires combinations that are not approved by Saab can negatively affect the car’s directional stability, steering and brak- ing in both wet and dry conditions.

The wheels and tires have been carefully matched to the characteristics of the car and play a key role in its outstanding roadhold- ing and handling. Do not take it for granted that a wheel/tire combination will work in the best possible way, just because it can be fitted to the car. To ensure that the speedometer is as accu- rate as possible it should be reprogrammed if wheels of a different dimension are fitted. Contact a Saab dealer. Because of front wheel drive, the front tires tend to wear faster than the rear ones. New tires should always be fitted in pairs, so that tires on the same axle have the same amount of tread. Store wheels lying flat or hanging – never standing upright.

NOTICE

Always consult your Saab dealer before changing the car’s wheels or tires on your Saab. Wide wheels and tires with side walls that are too low can: (cid:127) be damaged in potholes, etc.

(cid:127) cause springs, shock absorbers and wheel bearings and body mountings to be overloaded.

(cid:127) affect the function of the Electronic

Stability Program (ESP).

The speed and load limits of the tires must not be exceeded; see page 266.

Wheels larger than 17" must not be fitted on the Saab 9-3 for reasons above. The permissible offset is 1.61 inch (41 mm).

93U SM 06.book Page 261 Friday, February 18, 2005 1:15 PM

WARNING

Mixing tires could cause you to lose control while driving. If you mix tires of different sizes or types (radial and bias- belted tires), the vehicle may not handle properly, and you could have a crash. Using tires of different sizes may also cause damage to your vehicle. Be sure to use the same size and type tires on all wheels. It’s all right to drive with your compact spare temporarily, it was devel- oped for use on your vehicle. See “Compact spare” on page 270.

WARNING

If you use bias-ply tires on your vehicle, the wheel rim flanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on your vehicle.

Uniform Tire Quality Grading Quality grades can be found where applica- ble on the tire sidewall between tread shoul- der and maximum section width. For exam- ple:

Treadwear 200 Traction AA Temperature The following information relates to the system developed by the United States National Highway Traffic Safety Administra- tion, which grades tires by treadwear, trac- tion and temperature performance. (This applies only to vehicles sold in the United States.) The grades are molded on the side- walls of most passenger car tires. The Uni- form Tire Quality Grading system does not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-pro- duction tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Perfor- mance Criteria (TPC) standards.

Car care

261

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the govern- ment course as a tire graded 100. The rela- tive performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service prac- tices and differences in road characteristics and climate.

Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades repre- sent the tire’s ability to stop on wet pave- ment as measured under controlled condi- tions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warn- ing: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.

93U SM 06.book Page 262 Friday, February 18, 2005 1:15 PM

262

Car care

Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dis- sipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temper- ature can lead to sudden tire failure. The grade C corresponds to a level of perfor- mance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Wheel Alignment and Tire Balance The wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall per- formance. Scheduled wheel alignment and wheel bal- ancing are not needed. However, if you notice unusual tire wear or your vehicle pull- ing one way or the other, the alignment may need to be reset. If you notice your vehicle vibrating when driving on a smooth road, your wheels may need to be rebalanced.

Wheel Replacement Replace any wheel that is bent, cracked or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer if any of these conditions exist. Your dealer will know the kind of wheel you need. Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new Saab original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle.

WARNING

Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts and wheel nuts for replacement.

93U SM 06.book Page 263 Friday, February 18, 2005 1:15 PM

Notice: The wrong wheel can also cause problems with bearing life, brake cool- ing, speedometer or odometer calibra- tion, headlamp aim, bumper height, vehi- cle ground clearance and tire or tire chain clearance to the body and chassis. See “Changing a tire” on page 273.

WARNING

When fitting just one new pair of tires, these should be fitted to the rear wheels, as these are more critical to the direc- tional stability of the car (e.g. on braking or in a skid). The existing rear wheels should therefore be moved to the front.

Used Replacement Wheels

Tire Chains

WARNING

WARNING

Car care

263

Putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how far it’s been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.

If your vehicle has 235/45 R17 size tires, don’t use tire chains, there’s not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts. The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash. Use another type of traction device only if its manufacturer recommends it for use on your vehicle and tire size combination and road conditions. Follow that manu- facturer’s instructions. To help avoid damage to your vehicle, drive slowly, readjust or remove the device if it’s contacting your vehicle, and don’t spin your wheels. If you do find traction devices that will fit, install them on the front tires.

93U SM 06.book Page 264 Friday, February 18, 2005 1:15 PM

264

Car care

Notice: If your vehicle does not have 235/45R17 size tires, use tire chains only where legal and only when you must. Contact your Saab dealer regarding suit- able snow chains. Install them on the front tires and tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer’s instructions. If you can hear the chains contacting your vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage your vehicle.

If a Tire Goes Flat It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blowout”, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire will create a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to main- tain lane position, and then gently brake to a stop well out of the traffic lane. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you’d use in a skid. In any rear blowout, remove your foot from the acceler- ator pedal. Get the vehicle under control by steering the way you want the vehicle to go. It may be very bumpy and noisy, but you can still steer. Gently brake to a stop – well off the road if possible. If a tire goes flat, the next part shows how to use your jacking equipment to change a flat tire safely.

Tire Sidewall Labeling Useful information about a tire is molded into it´s sidewall. Tire size: The tire size ia a combination of letters and numbers used to define a partic- ular tire´s width, height, aspect ratio, con- struction type and service description. Department of Transportation (DOT): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety standards. Tire Identification Number (TIN): The let- ters and numbers following DOT code are the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manu- factured. The TIN is molded onto both sides of the tire. Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread.

93U SM 06.book Page 265 Friday, February 18, 2005 1:15 PM

Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on the performance factors: treadwear, traction and temperature resis- tance. For more information see “Uniform Tire Quality Grading” on page 261. Maximum Cold Inflation Load Limit: Max- imum load that can be carried and the max- imum pressure needed to support that load. For information on recommended tire pres- sure see “Recommended lowest tire pres- sure, cold tires” on page 306 and “Loading Your Vehicle” on page 267.

Tire Size The following illustration shows an example of a typical passenger car tire size.

215 / 55 R 16 93 H

a Tire Width b Aspect Ratio c Belt Rating d Rim diameter e Load range f Speed rating

Tire Width: The three-digit number indi- cates the tire section width in millimeters from sidewall to sidewall.

Car care

265

Aspect ratio: A two-digit number that indi- cates the tire height-to-width measure- ments. For example, if the tire size aspect ratio is “55”, as shown in item “C” of the illus- tration, it would mean that the tire´s sidewall is 55% as high as it is wide. Belt Rating: A letter code is used to indicate the type of ply construction in the tire. The letter “R” means radial ply construction; the letter “D” means diagonal or bias ply con- struction; and the letter “B” means belted- bias ply construction. Rim Diameter: Diameter of the wheel in inches. Load range: The load range represents the load carry capacity a tire is certified to carry. Speed Rating: The maximum speed that a tire is certified to carry a load. Speed ratings range from “A” to “Z”.

93U SM 06.book Page 266 Friday, February 18, 2005 1:15 PM

266

Car care

Tire markings An example of the meaning of the different markings in a tire size is given below for a tire size of 225/45 R17 94H:

225 Tire section width, mm

Aspect ratio, i.e. the section height as a percentage of the section width

45
R Radial ply

Wheel rim diameter 17 in at bead seats

17
94 Tire load index H Speed rating

Tire load indices

Tire approved for max. 1355 lbs. (615 kg)

91
93 Max. 1433 lbs. (650 kg) 94 Max. 1477 lbs. (670 kg) 95 Max. 1521 lbs. (690 kg) 97 Max. 1609 lbs. (730 kg)

Speed ratings

Tire approved for speeds up to 100 mph (160 km/h)

S Max. 112 mph (180 km/h) T Max. 118 mph (190 km/h) H Max. 130 mph (210 km/h) V Max. 149 mph (240 km/h) W Max. 168 mph (270 km/h) Y Max. 186 mph (300 km/h)

TIN-code a Manufacturer´s Identification Mark b Tire Size c Tire Type Code d Date of Manufacture

93U SM 06.book Page 267 Friday, February 18, 2005 1:15 PM

Loading Your Vehicle

This label can only be found on vehicles sold in the U.S. Vehicles sold in Canada have the tire information label in the glove box, see page307.

This is an example of what your vehicle´s Tire-Loading Information/Certification label might look like. It is located on the B-pillar and shows how much weight your vehicle may properly carry. The label tells you the proper size, and recommended inflation pressures for the tires on your vehicle. It also gives you important information about the number of people that can be in your vehicle and the total weight that you can carry. This weight is called the Vehicle Capacity Weight, and includes the weight of all occupants, cargo and all nonfactory- installed options.

Tire Terminology and Definitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the com- bined weight of optional accessories, for example, automatic transmission, power steering, power brakes, power windows, power seats, radio and air conditioning. Aspect Ratio: The relationship of a tire´s height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other rein- forcing materials. Bias Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at alternate angles substantially less than 90 degrees to the centerline of the tread. Cold Inflation Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascal (kPa), before a tire has built up heat from driving. See “Inflation - Tire Pressure” on page 257. Curb weight: This means the weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil and coolant, without passengers and cargo.

Car care

267

DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation motor vehicle safety stan- dards. The DOT code includes the Tire Identification Number (TIN), an alphanu- meric designator which can also identify the tire manufacturer, production plant, brand and date of production. GVWR: Gross Vehicle Weight Rating see “Loading Your Vehicle” on page 267. GAWR FRT: Gross Axle Weight Rating for the front axle, see “Loading Your Vehicle” on page 295. GAWR RR: Gross Axle Weight Rating for the rear axle, see “Loading Your Vehicle” on page 267. Intended Outboard Sidewall: The side of an asymmetrical tire that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. There are 6.9 kPa to one psi. Light Truck (LT-Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles. Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire.

93U SM 06.book Page 268 Friday, February 18, 2005 1:15 PM

268

Car care

Maximum Load rating: The load rating for a tire at the maximum permissible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehi- cle capacity weight; and production options weight. Maximum Permissible Inflation Pres- sure: The maximum cold inflation pressure to which a tire may be inflated. Normal occupant weight: The number of occupants a vehicle is designed to seat mul- tipled by 150 pounds (68 kg). See “Loading Your Vehicle” on page 267. Occupant Distribution: Designated seat- ing positions. Outward Facing Sidewall: The side of a asymmetrical tire that has a particular side that faces outward when mounted on a vehi- cle. The side of the tire that contains a white- wall bears white lettering or bears manufac- turer, brand and or model name molding on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles.

Recommended Inflation Pressure: Vehi- cle manufacturer´s recommended tire infla- tion pressure shown on the tire placard, see “Inflation - Tire Pressure” on page 257 and “Loading Your Vehicle” on page 267. Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at substantially 90 degrees to the cen- terline of the tread. Rim: A metal support for a tire or a tire and tube assembly upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip pro- vided. Treadwear Indicators: Narrow bands, sometimes called “wear bars”, that show across the tread of a tire when only 2/32 inch of tread remains. See “When It Is Time for New Tires” on page 259.

Tread Width: The width of the tire´s tread. UTQGS: Uniform Tire Quality Grade Stan- dards, a tire information system that pro- vides consumers with ratings for a tire´s traction, temperature and treadwear. Rat- ings are determined by tire manufacturers using government testing procedures. The rating are molded into the sidewall of the tire. See “Uniform Tire Quality Grading” on page 261. Vehicle Capacity Weight: Is the number of designated seating positions multipled by 150 pounds (68 kg) plus the rated cargo load. See “Loading Your Vehicle” on page 267. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight and cargo weight. Vehicle Placard: A label permanently attached to a vehicle showing original equipment tire size and the recommended cold inflation pressure. See “Loading Your Vehicle” on page 267.

93U SM 06.book Page 269 Friday, February 18, 2005 1:15 PM

Steps for Determining Correct Load Limit 1 Locate the statement “The

combined weight of occupants and cargo should never exceed XXX pounds” on your vehicle´s placard.

2 Determine the combined weight of the driver and passengers that will be riding in your vehicle.

3 Substract the combined weight of

the driver and passengers from XXX kilograms or XXX pounds.

4 The resulting figure equals the avail- able amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of avail- able cargo and luggage load capac- ity is 650 lbs. (1400–750 (5x150) = 650 lbs.).

5 Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calcu- lated in Step 4.

6 If your vehicle will be towing a trailer,

load from your trailer will be trans- ferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehi- cle.

Car care

269

Winter tires Winter (snow) tires are recommended for winter climates where the majority of your driving will be done on snow and ice. Winter tires should be fitted to all four wheels to maintain a proper balance. Your Saab dealer can advise you of to the correct size tire for your car (if different from the original size) and also supply Saab approved winter tires pre-mounted on steel or alloy rims. Winter tires normally use a different speed rating compared to summer/all season tires. Make sure not to exceed the stated speed rating on the tires you use.

93U SM 06.book Page 270 Friday, February 18, 2005 1:15 PM

270

Car care

Date code

Tire date code Tires should be regarded as perishable goods. As the tires age, the rubber becomes progressively harder, and the roadholding ability of the tires diminishes. This is partic- ularly true on winter tires. Tires have a code that specifies their date of manufacture. The first two digits denote the week number and the last two digits the year. Accordingly, a date code of 3701 signifies that the tire was manufactured in week 37, 2001.

The spare tire, the tools and the jack with its crank are carried under a panel in the trunk. Fold the carpeting forward to ease access to the tools and spare tire. The screwdriver handle has a “button” for removing plastic rivets. This type of rivet must be removed when changing the light bulb in the trunk lid (see page 241). Your Saab is equipped with a trip computer and you can use its “Speed warning” func- tion, to monitor driving speed since you must not exceed 50 mph (80 km/h), see page 94.

Compact spare

WARNING

The spare tire or punctured tire must be stowed under the trunk floor, and secured in place with the retaining nut.

The compact spare is light and easy to handle when changing the tire. Its use is only permitted when a standard tire has sus- tained a puncture. The maximum life of the tire is only just over 2,000 miles (3,500 km). Do not exceed 50 mph (80 km/h) with the compact spare fitted. The tire pressure should be 60 psi (420 kPa). Put the punctured tire in the spare wheel well under the trunk floor. “Driving with the compact spare tire”, see page 208. Have the standard tire repaired and refitted as soon as possible.

93U SM 06.book Page 271 Friday, February 18, 2005 1:15 PM

Car care

271

life of the tire is only just over 2,000 miles (approx. 3,500 km).

(cid:127) Refit the standard tire as soon as possi-

ble.

Important considerations when driving with a compact spare tire: (cid:127) The car’s ground clearance is reduced. (cid:127) The car must not be driven with more than

one compact spare tire at a time.

(cid:127) Avoid driving against the curb. (cid:127) Do not use snow chains. (cid:127) Do not fit the wheel cover - this would

conceal the warning text.

Tools under a panel in the trunk

NOTICE

To avoid damaging a alloy wheel of a punctured tire, this can be temporarily placed outside up in the spare wheel well but only while driving to the closest work- shop. As a general rule, all heavy loads must be well secured in the trunk (see page 149).

Driving with a compact wheel fitted

WARNING

(cid:127) Do not exceed 50 mph (80 km/h). The tire can overheat affecting the car’s roadholding.

(cid:127) Tire pressure: refer to page 304. (cid:127) The spare tire or punctured tire must be stowed under the trunk floor, and secured in place with the retaining nut.

Observe the following when the compact spare tire is fitted: (cid:127) The compact spare is light and easy to

handle when changing a tire.

(cid:127) Do not drive further than necessary with the compact spare fitted - the maximum

93U SM 06.book Page 272 Friday, February 18, 2005 1:15 PM

272

Car care

93U SM 06.book Page 273 Friday, February 18, 2005 1:15 PM

Changing a tire

WARNING

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. The jack provided with your vehicle is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. Use the jack provided with your vehicle only for chang- ing a flat tire.

Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving:

1 Set the parking brake firmly. 2 If you have an automatic transmis-

sion, put the shift lever in PARK (P). For a manual transmission, leave the car in gear (1st or REVERSE (R)).

3 Turn off the engine and do not restart

while the vehicle is raised.

4 Do not allow passengers to remain in

the vehicle.

To be even more certain the vehicle won't move, you should put blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire, on the other side, at the opposite end of the vehicle.

(cid:127) The car jack is designed solely for use

in changing a tire or fitting snow chains. It must not be used to support the car during repair work or servicing.

(cid:127) Never crawl under a car that is

supported only by a jack. Always use axle stands.

(cid:127) Raising your vehicle too high or with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle, and raise the vehicle only far enough off the ground so there is enough room for the spare tire to fit (no more than 25 mm or 1 inch clearance between the ground and the bottom of the tire).

(cid:127) Switch on the hazard warning lights if

the car is on a road.

Car care

273

(cid:127) The jack should be stored correctly under the carpeting in the trunk. If it lies loose in the car, it could thrown forward and cause personal injury in the event of a crash or if the car rolls over.

(cid:127) Grit, salt and rust can clog the inner

threads of the wheel bolts if the car has been driven for several years exclu- sively with alloy wheels. If steel wheels are being installed, the bolt hole threads in the brake hubs should be cleaned before the thinner steel wheels are fitted. It may other- wise not be possible to achieve the correct clamping force, despite tight- ening the wheel bolts to the correct torque.

93U SM 06.book Page 274 Friday, February 18, 2005 1:15 PM

274

Car care

When the car has to be lifted, the jack must be positioned at one of the four jacking points (front or rear) under the sill members. If a floor jack is used, the lifting plate must be positioned under the normal jacking points, see illustration. If the car is equipped with a towbar, the jack can also be placed under this.

NOTICE

Apply the jack only to the jacking points indicated on the body.

1 Wind the jack up to a suitable height

before placing it under the jacking point. Each jacking point is indicated by an arrow on the sill (see illustration). Make sure that the jack fully engages the jacking point in the underside of the sill member and that the entire foot of the jack is steady and flat on the ground. The jack must not stand on snow, ice or similar. Wind up the jack until it just begins to lift the car.

Marking of jacking points

Jacking points

2 It is not necessary to remove the wheel

cover. If, none the less, you wish to remove the wheel cover, take hold of the outer edge and pull it straight out. Loosen the wheel bolts half a turn.

3 Wind the jack to raise the wheel clear of the ground. Remove the wheel bolts and lift off the wheel.

4 Clean any rust or dirt from the contact surfaces between the wheel and brake disc. Do not wipe away the grease in the wheel hub.

5 Add a thin layer of grease on the bolts

before fitting, see page 276. Fit the wheel and screw in the bolts in the sequence shown on page 276 (opposite pairs). Tighten the bolts enough for the bolts and wheel to be seated correctly.

6 Lower the car and tighten the wheel

bolts to torque in sequence as shown on page 276. Tightening torque: Light-alloy wheels: 80 ft.lb. (110 Nm). Steel wheels: 80 ft.lb. (110 Nm).

93U SM 06.book Page 275 Friday, February 18, 2005 1:15 PM

Car care

275

Jacking points for floor jack

Clean any rust or dirt from the contact sur- faces between the wheel and brake disc.

Do not wipe away the grease in the wheel hub.

NOTICE

(cid:127) Do not overtighten the bolts using a

impact wrench: not only can this damage the wheels but it can also make it impossible to undo the bolts using the wheel wrench in the car’s toolkit.

(cid:127) When refitting a wheel cover, make

sure that the valve protrudes through the marked recess in the wheel cover.

7 Retouching the wheel bolts after twenty

or so miles. Tightening torque: Light-alloy wheels: 80 ft.lb. (110 Nm). Steel wheels: 80 ft.lb. (110 Nm).

We advise against using wheels with large ventilation slots in winter, as the brake com- ponents are then more exposed to slush, road salt and grit. If you fit wheels of a different dimension, the speedometer can be reprogrammed to ensure it is as accurate as possible. We rec- ommend that you contact a Saab dealer. Driving with tire chains 3, see page 196

93U SM 06.book Page 276 Friday, February 18, 2005 1:15 PM

276

Car care

Grease the surfaces indicated with a thin layer of grease

Tightening sequence, wheel bolts

Upholstery and trim To remove fluff and hairs from the seats, door armrests and headlining, use a vacuum cleaner, a moist lint-free cloth, or a clothes brush. Remove spots and dirt using a cloth moistened with lukewarm soapy water. When using a stain remover, always work from the outside towards the centre to avoid leaving a ring. If a soiled ring or spot should remain, it can usually be removed using lukewarm soapy water or water alone. Spots left by liquids, such as soft drinks or thin oil, must be removed at once with an absorbent material, such as kitchen towel- ling. Then clean with a stain remover. White spirit is recommended for removing grease and oil stains. A medium stiff brush may also be used.

Safety belts

WARNING

If the car is involved in a crash, the safety belts, belt pretensioners and other asso- ciated components must be inspected. We recommend that you contact a Saab dealer. Never make any alterations or repairs to the safety belts yourself. We recommend that you contact a Saab dealer dealer.

Check the function of the safety belts regu- larly as follows: (cid:127) Hold the diagonal strap and pull it sharply. The safety belt should lock and it should not be possible to withdraw it further.

Check the anchorage points in the floor. They must not have suffered rust damage. If a belt is worn or has any fraying edges, it should be replaced. Safety belts must not come into contact with substances such as polishes, oil or chemi- cals. If the belts get dirty, wash them with warm water and a detergent or have them replaced.

93U SM 06.book Page 277 Friday, February 18, 2005 1:15 PM

Cleaning and caring for leather upholstery The principal reason for treating leather upholstery is to maintain its elegant appear- ance and to provide it with a protective film. Disco lour at ion caused by dust and wear mainly affects the lighter shades, although this is not detrimental to the leather, indeed, the patina resulting from use is often consid- ered desirable in leather. But if the leather is allowed to become too grubby, it can start to look shabby. The leather upholstery should be cleaned and reconditioned twice a year in conjunc- tion with spring and autumn inspections. In very warm, dry climates the leather may need more regular reconditioning. Use con- ventional leather care products. Follow the instructions on the packaging. Do not use unknown harsh polishing agents, cleaning agents, sprays, coarse soap or hot water.

Textile carpeting Textile carpeting should be vacuum cleaned regularly. Carpeting can also be cleaned using a brush or sponge and carpet shampoo. For safety reasons, vacuum cleaners that are not earthed (grounded) must not be used out of doors.

Engine bay The engine bay should be cleaned with an engine decreasing and rinsed with hot water. The headlights must be covered over. Do not use a pressure washer. Avoid spraying electrical components and con- nectors. Do not use petrol as a cleaning agent or sol- vent when carrying out repairs or mainte- nance. Saab recommends the use of envi- ronmentally-friendly decrescendos.

Car care

277

Washing The bodywork must be washed frequently. When the car is new, the body should be washed by hand using plain cold water and a clean, soft brush through which the water flows. Automatic caresses should be avoided when the car is new. After 5–6 months the paintwork will have hardened. To facilitate cleaning, a suitable detergent can be added to the water, which should be lukewarm. Remove any bird droppings without delay, as these can discolor the paintwork and prove difficult to polish out. Lay a wad of wet paper on the patch of dirt and leave it for a minute or so. It will then be easy to wash off the dirt. Use a soft cloth moistened with white spirit to remove splashes of tar or asphalt. Do not use strong cleaners, as these can dry out the paintwork.

NOTICE

Do not use alcohol-based cleaners on the plastic lenses of the front or rear lights, as these can cause a crackling effect on the lenses. The door mirrors should be folded in before the car enters an automatic car wash.

The underside of the car also needs wash- ing regularly, and this should be done extra

93U SM 06.book Page 278 Friday, February 18, 2005 1:15 PM

278

Car care

thoroughly at the end of winter. Clean the underside of the car by hand if the car is usu- ally washed in an automatic car wash with- out special facilities for underbody cleaning. Never wash or leave the car to dry in the sun, but wipe it dry with a chamois leather immediately after washing to avoid smears and streaks. Clean the inside of window glass using a proprietary window cleaner. This is particu- larly important when the car is new, as upholstery and trim have a tendency to sweat a little at first. Keep the glass well polished, as this helps to prevent misting. Clean the outside of the windows with Saab washer fluid. This is especially important if the car has been washed in an automatic car wash, as sometimes a wax treatment is used that can contaminate the windshield and impair the performance of the wipers. In the U.S., Saab offers a full complement of car care products. See your dealer or visit us at www.saabcatalog.com.

Convertible: (cid:127) Wash the soft top with a mild soap solu-

tion and lukewarm water. For spot clean- ing the top, a finger nail brush can also be used. Stroke the brush in the direction of the fabric, not across the threads. If a pressure washer is used be heedful of the following recommendations: (cid:127) on the lower part of the car (not higher than the door handles): max pressure of 100 bar and not closer than 8 in. (20 cm).

(cid:127) on the upper part of the car: tax pres- sure of 100 bar and not closer than 32 in. (80 cm).

(cid:127) Do not use any drying chemicals or water-

proofing agents.

(cid:127) Avoid automatic car washes.

NOTICE

(cid:127) Try your brakes on leaving a car wash.

Wet brake discs reduce the perfor- mance of the brakes.

(cid:127) Fixed antennae, such as for a mobile

phone, must be removed if the car goes through an automatic car wash.

(cid:127) Cars with Saab Parking Assistance: Do not spray the sensors or closer than 8 in. (20 cm) to the sensors with a pressure washer, as this can damage them.

(cid:127) 93U SM 06.book Page 279 Friday, February 18, 2005 1:15 PM

Waxing and polishing Do not wax a new car during the first three or four months. In fact, there is no need to polish the car before the paintwork has started to dull through oxidation. Other than in exceptional cases, do not use abrasive polishes containing a cutting agent on a new car. Always wash the car thoroughly before waxing or polishing.

Touching up the paint Damaged paintwork should be treated as soon as it is discovered: the longer it is left, the greater the risk of corrosion. The anti- corrosion warranty does not cover corrosion resulting from untreated defects. Paintwork damage sustained in a crash is usually extensive and can only be properly restored by professionals. However, you can repair small scratches and stone chip damage yourself. The nec- essary tools and materials, such as primer, touch-up paint and brushes, are available from a workshop. We recommend that you contact a Saab dealer. In the case of minor flaws in the paintwork, where the metal has not been exposed and an undamaged layer of paint remains, touch-up paint can usually be applied directly, after any dirt has been scraped away using a pointed knife. If corrosion has already set in, such as the result of stone-chip damage, use a pointed knife to scrape off all surface rust. If possi-

Car care

279

Surface treatment composition 1 Body panel 2 Zinc (certain components only) 7.5 µm 3 Phosphate coating 3 –5 µm 4 Cathodic ED 23 µm 5 Intermediate coat 35 µm 6 Metallic base/solid base 11 µm 7 Clear enamel 45 µm

ble, the damaged area should be taken back to the bare metal. The metal should then be primed with two thin coats of primer applied by brush. After the primer has dried, apply several thin layers of topcoat until the surface of the repaired area is flush with the surrounding paintwork. Stir both primer and touch-up paint thor- oughly before use and allow each coat to dry before applying the next. Two-coat enamel As the name implies, two-coat enamel is applied in two operations. The first coat, the base color, contains the pigment, metal flakes and binder. The second coat consists of a clear enamel, which provides the final gloss for the paintwork and protects the base from moisture and environmental con- taminants. Touch-up stone-chip damage as follows: 1 Thoroughly clean the damaged area. 2 Then apply the primer, base color and finally, the clear enamel. To achieve the best finish, apply two or three coats of primer.

93U SM 06.book Page 280 Friday, February 18, 2005 1:15 PM

Car care

280
Anti-corrosion treatment The entire car undergoes a series of anti- corrosion processes during production. These include electrophoretic priming, PVC-based coating to protect against stone chip damage and corrosion, and treatment of body cavities and members with thin, penetrating rustproofing oil. In addition, most body panels, such as the hood, doors and floor pan are galvanized. The anti-corrosion treatment on some parts of the car is constantly exposed to wear and prone to damage. This applies particularly to the underside of the car and inside the wheel arches, where grit, road salt and the like that are thrown up can give rise to cor- rosion where the underseal has worn away. The extent of this obviously depends on the conditions in which the car is used. Accordingly, make it a habit to hose the underside of the car often and to inspect the condition of the underseal. The anti-corro- sion warranty does not relieve the car owner of the need to carry out normal maintenance to the rustproofing and to make good any damage.

Use a hose to clean the underside of the car thoroughly. After it has dried, use a brush or spray to apply a viscous anti-corrosion agent to any worn or damaged areas, to prevent the onset of corrosion. Even after the anti-corrosion warranty has expired, it makes good sense to continue to maintain the rustproofing. Seams in the body, especially those in the doors and trunk lid, are particularly vulnera- ble to corrosion from the outside, caused by grit and salt thrown up from the road, and to corrosion from the inside, largely as a result of condensation. Keep the seams clean and at the first sign of any rust, apply a thin, pen- etrating, anti-corrosion oil. Your Saab dealer will be pleased to give you further advice.

What causes rust? Steel body panels of automobiles are sub- ject to rusting whenever air and moisture manage to penetrate the protective finish. Body panels may rust through if the process is unchecked. Rusting can occur wherever water is trapped or where the car’s panels are continuously damp. Damage to paint and undercoating by stones, gravel and minor crashes immedi- ately exposes metal to air and moisture. Road salts used for de-icing will collect on the bottom of the car and promote rusting. Areas of the country with high humidity have a greater potential for rust problems, espe- cially where salt is used on roads or there is moist sea air. Industrial pollution (fallout) may also damage paint and promote rust- ing.

Car care

281

Inspect the undercoating and touch up if necessary. Pay particular attention to the fenders and wheel housings, which are exposed to abrasion by flying gravel, etc. If the composition has worn or flaked off, the steel must be thoroughly cleaned and dried before a fresh coat is applied. The cleaning is best done with a scraper and a steel wire brush, followed by washing with solvent. Apply the new coating thinly, otherwise it may run off or fall off when dry.

93U SM 06.book Page 281 Friday, February 18, 2005 1:15 PM

Preventive maintenance The following procedures are necessary to help protect against rusting. Refer also to the terms and conditions of the Performa- tion Limited Warranty described in the war- ranty booklet. 1 Wash the car frequently, and wax at

least twice a year. Under adverse conditions, where there is a rapid buildup of dirt, sand or road salt, wash your car at least once a week. After extreme exposure to salted snow or slush, evidenced by a white film on the car, wash the car immediately. Frequent washing will prevent paint damage from acid rain and other airborne contami- nants such as tree sap and bird drop- pings. If any of these contaminants are noticed on the car the finish should be washed immediately. (cid:127) Begin washing by rinsing the entire car with water to loosen and flush off heavy concentrations of dirt (include the underbody).

(cid:127) Sponge the car with a solution of either a good quality car soap or mild general purpose (dish washing) detergent and water.

(cid:127) Rinse car thoroughly with clean water. (cid:127) After washing, check and clear all drains in doors and body panels.

(cid:127) Wipe the car dry, preferably using a

chamois.

2 Clean the underside of the car during the winter. Use high pressure water to clean the car’s underside (floor panels, wheel wells) at least at mid-winter and in the spring.

3 Inspect the car frequently for leaks or

damage, and arrange for needed repairs promptly. After washing or after heavy rain, check for leaks. When wash- ing the car inspect body surfaces for paint damage. While checking for leaks, lift the floor mats and check underneath them. Water can collect in these areas and remain for prolonged periods. Dry any wet areas including the floor mats. Have leaks repaired as soon as possi- ble. Use touch-up paint to repair small scratches or minor finish damage. Areas where metal is exposed will rust quickly and MUST be repaired immediately by touch-up or professional repainting. Rust must be removed, the bare metal primed and painted. Major body damage should be repaired immediately and new panels or exposed areas should be undercoated with anti- corro- sion material. Repairs of this type are the owner’s responsibility and are not covered under warranty.

93U SM 06.book Page 282 Friday, February 18, 2005 1:15 PM

Car care

282
Recovery and/or recycling of automotive materials A typical car consists of metals (65–75 %), plastics (10–15 %), rubber (5 %) and small quantities of glass, wood, paper and tex- tiles. The recycling of metals has been com- monplace for a long time now. To facilitate the sorting of other materials, plastic parts, for instance, have been marked to identify the precise nature of the plastic.

Air conditioning (A/C)

WARNING

(cid:127) All repairs and adjustments to the A/C system must be carried out at a Saab dealer authorized for this kind of work. (cid:127) The A/C system is pressurized. Do not break any connections or undo A/C system components.

(cid:127) Escaping gas can cause eye injury or

other personal injury.

NOTICE

(cid:127) The A/C system is designed for use

with R134a refrigerant.

(cid:127) Refrigerant handling requires special equipment and special procedures for charging and draining the system.

(cid:127) Never mix R 134a with other refriger-

ants.

Troubleshooting If a fault occurs in the A/C system, there are a number of checks you can perform your- self. If the fault persists, however, have the system checked at a workshop. We recom- mend that you contact a Saab dealer.

Note: When the A/C system is running, the intake air is dehumidified. The resultant condensa- tion that forms on the evaporator is drained off under the car. When the car is parked, this may result in a small puddle forming on the ground. The warmer the air and the higher the relative humidity, the more con- densation will be produced. Inadequate cooling a Check that the controls for temperature and air distribution are correctly set; see “Manual climate-control system 3” on page 110.

b Check that the condenser (in front of the radiator) has not become clogged with dirt and insects.

c Make sure that the compressor drive

belt does not slip (see page 229).

d Check the fuses for the ventilation fans

and compressor (see page 249).

93U SM 06.book Page 283 Friday, February 18, 2005 1:15 PM

Maintenance

NOTICE

Do not use a pressure washer when cleaning the condenser or radiator due to the risk of damage.

(cid:127) The compressor drive belt should be inspected under the regular service program.

(cid:127) Clean away dirt and insects from the

condenser and radiator to prevent clog- ging. When washing the car, use the hose to spray the radiator and condenser (located in front of the radiator) from both sides (both from the front of the car and from inside the engine bay). Do not use a pressure washer. Caution: Do not hose down the radia- tor and condenser while the engine is hot.

Other than in extremely cold weather, do not screen the radiator, e.g. with netting, as this will greatly diminish its cooling capacity. (cid:127) Applicable to the manual climate control system - During cold months the air condi- tioning should be switched on once or twice a month and run for 5–10 minutes during highway driving once the engine is warm. This action saves the gaskets in the compressor from being spoiled. The compressor uses a lubricant that circu- lates with the coolant.

Note: The A/C system cannot be switched on when the outside temperature is below 32°F (0°C). Turn on the A/C system when the car is standing in a warm place. Simplest is to always have the A/C button pressed in. The A/C system will then cut in automatically when the outside temperature is high enough.

Car care

283

Headlight aiming

WARNING

Before checking/adjusting the headlight aiming, switch off the engine to avoid danger of fingers and hands being injured by moving parts. The radiator fan can start up even when the engine is switched off.

The vehicle has a visual optical headlight aiming system equipped with vertical aiming device. The aim has been preset at the factory and should normally not need further adjustments. If your headlights are damaged in a crash, the headlight aim may be affected. If you believe your headlights need to be re- aimed, we recommend that you take it to your Saab dealer for service. However, it is possible for you to re-aim your headlights as described in the following procedure.

NOTICE

To make sure that your headlights are aimed properly read all instructions before beginning. Failure to follow these instructions could cause damage to headlight parts or a not correctly aimed headlight.

93U SM 06.book Page 284 Friday, February 18, 2005 1:15 PM

284

Car care

1 Wall or garage door. 2 25 ft (7.6 m) between wall and headlight lens. 3 Measurement from the ground to the low beam aiming marker on the headlight lens. 4 Same measurement as (3) but substract 2 inches.

Vertical aiming device

To check the aim, the vehicle should be properly prepared as follows: (cid:127) The vehicle shall be placed so that the

headlights are 25 ft (7.6 m) from a light colored wall or other flat surface. The aiming area should be darkened, this will improve your ability to see the beam of the low beam headlight being aimed. An optical headlamp aimer can also be used and will than replace the wall.

(cid:127) The vehicle must have all four wheels on a perfectly level surface which is level all the way to the wall or other flat surface. (cid:127) The vehicle should be placed so it is per- pendicular to the wall or other flat surface.

(cid:127) The vehicle should be unloaded and fuel

tank full, and one person or 160 lbs. (75 kg) on the drivers seat.

(cid:127) The vehicle should be fully assembled

and all other work stopped while headlight aiming is being done.

(cid:127) The vehicle should not have any snow, ice

or mud attached to it.

(cid:127) Tires should be inflated to the prescribed

pressure.

(cid:127) Close all doors. (cid:127) Rock the vehicle to stabilize the suspen-

sion.

Headlight aiming is done with the vehicle low beam lamps. The high beam lamps will

1 Aiming marker on headlight lens

93U SM 06.book Page 285 Friday, February 18, 2005 1:15 PM

be correctly aimed if the low beam lamps are aimed properly. If you find that the headlight needs adjust- ment follow these steps: 1 Open the hood and locate the vertical aiming devices there are two vertical aiming devices which shall be turned simultaneously and the same amount of turns.

2 Locate the marker on the lens. 3 Measure the distance from the ground to

the aim marker No.1 on each lens. Subtract 2 inches.

4 At the wall or other flat surface, measure

from the ground to the recorded distance (see point 4) and draw a hori- zontal line the width of the vehicle.

5 Cars with xenon lights:

Xenon lights with automatic headlight levelling system must first do a refer- ence run before aiming: Start the engine and let the headlights do a reference run. Turn off the engine but leave the low beam on. Cars with halogen lights: Turn on the low beam headlights. Both variants: Place a piece of cardboard or equivalent (although not directly on the lens) in front of the headlight not being aimed. This should allow the beam cut-off of the headlight being aimed to be seen on the flat surface.

Car care

285

Horizontal line on wall or other flat surface Correctly adjusted low beam

Then follow the instructions in the optical headlight aimer instruction manual and point 1, 2, 5, and 6 in this instruction.

NOTICE

Do not cover a headlight directly on the lens to improve beam cut-off when aiming. Covering a headlight may cause excessive heat build-up that may cause damage to the headlight.

6 Turn the two vertical aiming screws

simultaneously in the same direction indicated on the headlight until the hori- zontal cut-off of the headlight is aligned with the horizontal line on the wall.

7 If an optical headlight aimer device is

used follow point 1 and 2 and center the lens of the optical headlight aimer device at the intersection of the two markers on the headlight lens.

93U SM 06.book Page 286 Friday, February 18, 2005 1:15 PM

286

Car care

(This page has been left blank.)

93U SM 06.book Page 287 Friday, February 18, 2005 1:15 PM

287
Customer Assistance and Information

Customer Assistance and Information

Maintenance schedule __ 288 Owner assistance ______ 290 Reporting Safety Defects

(USA) _______________ 291

Reporting Safety Defects

to the Canadian government__________ 291

Vehicle Data Collection

and Event Data Recorders ___________ 292

3 Asterisk means: equipment not fitted in all cars (can depend on model variant, engine variant, market specification, options or accessories).

Customer Assistance and Information

93U SM 06.book Page 288 Friday, February 18, 2005 1:15 PM

288
Maintenance schedule The Maintenance Schedule prescribes a service program to the purchaser/operator of a Saab that is reasonable and necessary to ensure the proper emission control sys- tems function, safety and reliability of the Saab automobile in normal use. Additional maintenance is recommended for specific components when the car is operated under certain severe conditions. Proper mainte- nance is always a good practice! Authorized Saab dealers are equipped and trained to meet your Saab’s service needs. They regularly receive up-to-date Saab ser- vice manuals and parts and technical ser- vice bulletins from Saab and are able, through their franchise agreement, to attend Saab service schools, obtain Saab special tools and technical assistance and pur- chase original equipment service and replacement parts. Today’s complex automobiles should only be entrusted to the most knowledgeable service professionals. A Saab dealer is your best choice.

TIME FOR MAIN SERVICE will be set when additional maintenance is necessary, such as air filter or spark plug replacement. When the message Time for service. is displayed, contact your Saab Dealer for a service appointment. Failure to perform scheduled maintenance in a timely manner may result in serious damage to key components or systems.

SERVICE INTERVALS A time for service message will illuminate on the Saab Instrument Display (SID) when the car is due for regular maintenance. There are three different messages that will appear:

TIME FOR INTERMEDIATE SERVICE indicates that an oil/filter change is required along with several inspections. This mes- sage is set by the engine management system which calculates service intervals based on several factors including driving habits, ambient temperature, number of cold starts, mileage driven and elapsed time since the last service. If mileage accumula- tion does not occur, the message will be set, and maintenance required at a maximum of 2 years.

TIME FOR MAIN AND INTERMEDIATE SERVICE indicates that an oil/filter change is required along with several inspections and addi- tional maintenance such as air filter or spark plug replacement.

93U SM 06.book Page 289 Friday, February 18, 2005 1:15 PM

Customer Assistance and Information

289

Engine oil and filter changes Changing the engine oil and filter is required at every service point. Use only a Saab approved long-life oil filter and engine oils meeting the SAE viscosity ratings and API service classifications stated in the “Techni- cal data” section of this Owner’s Manual. The use of extra additives in the oil is not necessary and is not recommended, and may be harmful to turbochargers. More frequent oil changes are recom- mended if your vehicle is operated under any of the following conditions: (cid:127) Most trips are less than 5–10 miles (8– 16 km). This is particularly important when outside temperatures are below freezing.

(cid:127) Most trips include extensive idling

(frequent stop-and-go traffic).

(cid:127) Most trips are through dusty areas (such

as construction zones). If the vehicle is used for delivery service, police, taxi or other commercial applica- tions.

If your driving habits match this description, have the engine oil and filter changed in- between normal services. These conditions cause the engine oil to break down faster. The Warranties and Service Record Book- let has provisions to record extra oil changes.

Service record retention It is the owner’s responsibility to retain ser- vice records. If possible, you should keep copies of all shop work orders for all service and repairs, whenever performed. As indi- cated in the new car and emission control system warranties, it is important to docu- ment that all necessary maintenance has been done.

HOW THE SERVICE RECORD IS ORGA- NIZED The service record is comprised of a series of coupons on which to record services as they are performed. There are additional coupons for documenting extra engine oil and filter changes, extra automatic trans- mission fluid services necessary for severe service conditions, and brake fluid changes.

HOW TO USE THE SERVICE RECORD COUPONS When the car is brought to a Saab dealer for scheduled maintenance, present the War- ranties & Service Record Booklet to the ser- vice manager. When the technician has completed the service, the technician will sign the maintenance record. The person responsible for quality assurance at the dealership will also sign and stamp the record with the dealer identification stamp.

Service costs Dealer pricing practices and labor for ser- vice work vary. Saab’s recommended ser- vice times for each service point do not include the labor required to replace wear items, such as wiper blades, brake pads or tires. Nor is labor to perform other service or repairs found to be necessary as a result of the inspections included in these times. Additional labor and parts will be charged for such work when necessary, except as covered under an applicable Saab warranty or any optional extended service contract. Transmission fluid changes or suspension alignment, when necessary, are also addi- tional. Dealer charges for general shop material, regulated hazardous waste removal, recy- cling expenses or other operation costs may also be applied to service and repair invoices and are apt to vary by dealer and location.

(cid:127) Customer Assistance and Information

93U SM 06.book Page 290 Friday, February 18, 2005 1:15 PM

290
Owner assistance Warranties and service problem assistance For complete information about all applica- ble warranties, including the New Car War- ranty, Perforation Warranty, Vehicle Emis- sion Warranty and Emission Perforation Warranty, consult the Warranties and Ser- vice Record Booklet which accompanies this Owner’s Manual. It also contains owner assistance information including Saab Roadside Assistance. If the booklet is lost or misplaced, a new one may be ordered through a Saab dealer or by contacting Saab. In the U.S. there is a national Customer Assistance Center at Saab Cars USA, Inc. The toll-free number to call from all 50 states is 1-800-955-9007. In Canada, please call the Saab Customer Assistance Centre at 1-800-263-1999. A list of authorized Saab sales and service dealers is available for those planning to travel in the United States and Canada. Canadian or U.S. travelers may call the Customer Assistance Center in the country in which they are traveling.

Change of Address Notification (U.S. and Canada) Two change of address cards are provided at the end of the Warranties and Service Record Booklet. Knowing your current address allows Saab to contact you in the event of a recall or service campaign. Please help us keep our records up to date for your own peace of mind. Service information Factory Service Manuals for the Saab 9-3 and 9-5 car lines can be ordered through your dealer. These are comprehensive manuals on CD rom, geared to use by pro- fessional technicians. Consult your Saab dealer for prices for your model.

93U SM 06.book Page 291 Friday, February 18, 2005 1:15 PM

Customer Assistance and Information

291

Reporting Safety Defects (USA) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to noti- fying Saab Cars USA, Inc. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Saab Cars USA, Inc. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424- 9393 (or 202/366-0123 in Washington D.C. area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline.

Reporting Safety Defects to the Canadian government If you live in Canada, and believe that your vehicle has a safety defect, you should immediately notify Transport Canada, in addition to notifying General Motors of Canada Limited. You may write to Transport Canada at Box 8880, Ottawa, Ontario, K1G 3J2. In addition to notifying Transport Canada in a situation like this, we certainly hope you will notify us. In Canada, please call our Saab Customer Assistance Centre at 1- 800-263-1999. Or write: General Motors of Canada Limited Customer Assistance Centre, 1908 Colonel Sam Drive, Oshawa, Ontario, L1H 8P7.

93U SM 06.book Page 292 Friday, February 18, 2005 1:15 PM

292

Customer Assistance and Information

Vehicle Data Collection and Event Data Recorders Your vehicle, like other modern motor vehi- cles, has a number of sophisticated com- puter systems that monitor and control sev- eral aspects of the vehicle’s performance. Your vehicle uses on-board vehicle comput- ers to monitor emission control components to optimize fuel economy, to monitor condi- tions for air bag deployment and, if so equipped, to provide anti-lock braking and to help the driver control the vehicle in diffi- cult driving situations. Some information may be stored during regular operations to facilitate repair of detected malfunctions; other information is stored only in a crash event by computer systems commonly called event data recorders (EDR). In a crash event, computer systems, such as the Air Bag Sensing and Diagnostic Module (SDM) in your vehicle may record information about the condition of the vehi- cle and how it was operated, such as data related to engine speed, brake application, throttle position, vehicle speed, steering wheel angle, lateral acceleration, safety belt usage, air bag readiness, air bag perfor- mance, and the severity of a collision. This information has been used to improve vehi- cle crash performance and may be used to improve crash performance of future vehi- cles and driving safety. Unlike the data recorders on many airplanes, these on- board systems do not record sounds, such as conversation of vehicle occupants.

To read this information, special equipment is needed and access to the vehicle or the SDM is required. Saab will not access information about a crash event or share it with others other than (cid:127) with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee, in response to an official request of police or similar government office,

(cid:127) as part of Saab’s defense of litigation

through the discovery process, or

(cid:127) as required by law. In addition, once Saab collects or receives data, Saab may (cid:127) use the data for Saab research needs, (cid:127) make it available for research where

appropriate confidentiality is to be main- tained and need is shown, or

(cid:127) share summary data which is not tied to a specific vehicle with non-Saab organiza- tions for research purposes.

Others, such as law enforcement, may have access to the special equipment that can read the information if they have access to the vehicle or SDM. If your vehicle is equipped with OnStar®, please check the OnStar® subscription ser- vice agreement or manual for information on its operations and data collection.

(cid:127) 93U SM 06.book Page 293 Friday, February 18, 2005 1:15 PM

3 Asterisk means: equipment not fitted in all cars (can depend on model variant, engine variant, market specification, options or accessories).

Technical data 293
Technical data

General data __________ 294 297 Engine _______________ Engine oil_____________ 298 Fuel__________________ 299 Engines ______________ 300 Electrical system_______ 300 301 Drive belt _____________ Manual transmission ___ 301 302 Automatic transmission _ 302 Suspension ___________ Steering ______________ 302 Brake system__________ 303 Wheels and tires _______ 304 Plates and labels _______ 307

93U SM 06.book Page 294 Friday, February 18, 2005 1:15 PM

294

Technical data

General data Overall length, including bumpers: ___

Sport Sedan and Convertible _________ 182.5'' (4635 mm) SportCombi_______________________ 183.2'' (4654 mm) 80.2'' (2038 mm) 60.6'' (1539 mm) 105.3'' (2675 mm)

Overall width, including door mirrors __ Maximum height _________________ Wheelbase _____________________ Track:

Front ____________________________ 59.8'' (1524 mm) Rear ____________________________ 59.3'' (1506 mm) approx. 120 mm

Ground clearance at GVW _________ Number of seats (incl. driver):

Sport Sedan and SportCombi ________ 5
Convertible _______________________ 4

Turning circle:

Measured at vehicle extremities _______ 37.4 ft. (11.4 m) cars with V6 engine ________________ 40.0 ft. (12.2 m)

V.I.N. label on vehi- cles sold in U.S.A.

V.I.N. label on vehicles sold in Canada

Permissible load (in addition to the driver) = GVW minus curb weight. The maximum permissible axle load, front or rear, must not be exceeded. The precise curb weight of the vehicle and load capacity are specified in the vehicle registration documents.

Trunk length, Sport Sedan:

Rear seat raised ___________________ Rear seat lowered _________________

Trunk length, Convertible __________ Trunk length, SportCombi:

40.8'' (1036 mm) 69.8'' (1774 mm) 29.1" (740 mm)

Rear seat raised ___________________ Rear seat lowered _________________

39.9'' (1013 mm) 70.0'' (1777 mm)

Trunk volume (VDA):

Sport Sedan ______________________ Convertible, soft top raised___________ Convertible, soft top folded___________ SportCombi ______________________ SportCombi with rear seat lowered ____

15.0 cu.ft. (425 l) 12.4 cu.ft. (352 l) 8.3 cu.ft. (235 l) 14.8 cu.ft. (419 l) 45.0 cu.ft. (1273 l)

Technical data

295

Maximum roof load, Sport Sedan and Sport-

Combi ________________________

220 lbs. (100 kg)

Maximum load in trunk, Sport Sedan, Con-

vertible and SportCombi__________ The combined weight of occupants and

cargo should never exceed: Sport Sedan and SportCombi ________ Convertible _______________________

Maximum combined weight of driver and

passengers ___________________ Sport Sedan and SportCombi (5x150 lbs.)_______________________ Convertible (4x150 lbs.) _____________

175 lbs. (80 kg)

925 lbs. (420 kg) 775 lbs. (352 kg)

750 lbs. (340 kg) 600 lbs. (272 kg)

93U SM 06.book Page 295 Friday, February 18, 2005 1:15 PM

Curb weight

(i.e. with full fuel tank, full washer fluid res- ervoir, standard tools and spare wheel): Sport Sedan ______________________ 3200–3420 lbs. (1450–1550 kg) Convertible _______________________ 3570–3700 lbs. (1620–1680 kg)

SportCombi_______________________ xx

Gross vehicle weight (GVW):

Sport Sedan ______________________ 4120–4340 lbs. (1870–1970 kg) Convertible _______________________ 4460–4520 lbs. (2025–2050 kg)

SportCombi_______________________ xx

Maximum axle load:

Sport Sedan, front _________________ 2480 lbs. (1125 kg) Sport Sedan, rear __________________ 2230 lbs. (1010 kg) Convertible, front __________________ 2540 lbs. (1150 kg) Convertible, rear ___________________ 2310 lbs. (1050 kg) SportCombi_______________________ xx SportCombi_______________________ xx

Weight distribution:

Curb weight + driver (150 lbs. (68 kg)), front/rear, Sport Sedan and SportCombi GVW, front/rear, Sport Sedan and Sport- Combi ___________________________ approx. 50/50 %

approx. 60/40 %

93U SM 06.book Page 296 Friday, February 18, 2005 1:15 PM

296

Technical data

WARNING

(cid:127) The GVW and maximum axle loads must not be exceeded.

Note that if some accessories (e.g. towbar, CD changer) are fitted, the available load capacity is reduced by the weight of these.

(cid:127) When carrying a load in the trunk, make sure that it is lashed down securely, particularly when part or all of the rear seat is folded down.

Trailer: Trailer with brakes ________________