Download PDF Manual

If this message appears, stop the car as soon as it is safe to do so and allow the engine to idle until the message has gone out. The selector lever should be in position P.


93U SM 06.book Page 175 Friday, February 18, 2005 1:15 PM


Lock-up The transmission’s torque converter has a lock-up function. This can lock the torque converter, thus reducing the engine speed and fuel consumption. Kick-down When the accelerator is pressed down fully, a down change is made to optimize acceler- ation, e.g. for overtaking. Following this, the next higher gear will be selected at the optimum engine speed, unless you ease off the accelerator before reaching this. Driving in hilly country with a heavy load The transmission fluid can overheat when the gearbox is strained, for example, when driving with a trailer on hilly roads. To avoid the transmission fluid overheating, always drive with the selector lever in the D posi- tion. The adaptive gear change patterns are then active. High air temperatures or a faulty oil cooler can also cause the transmission fluid to overheat. Overheating reduces the service life of the fluid.


WARNING


Remember to use the braking effect of the engine (1st, 2nd or 3rd gear) when you are descending long or steep hills to spare the brakes. Overheating can cause the brakes to fade!


Towing Towing of cars with automatic transmission, see page 205. Descending hills If the speed of the car increases while descending a steep hill, despite the acceler- ator being released, the control module will change down. If you desire more powerful engine braking, manually select a lower gear (see page 178).


Starting and driving


175


Limp-home


NOTICE


Do not tow a trailer if limp-home mode is engaged.


If the transmission malfunctions, the control module will activate limp-home mode. Driv- ability will be affected to varying degrees. The following message is shown on the SID:


Gearbox malfunction. Limited performance. Contact Saab dealer.


In this mode, only 2nd and 5th gears are available. Select 2nd gear when driving at low speeds and 5th gear at higher speeds. 2nd gear must be selected manually. Select 5th gear manually or move the selector lever to D (see page 178).


Cars with 5-speed transmission In this mode, only 2nd and 5th gears are available. Select 2nd gear when driving at low speeds and 5th gear at higher speeds. 2nd gear must be selected manually. Select 5th gear manually or move the selector lever to D, see page 178.


Cars with 6-speed transmission 3 (cid:127) The car may be totally powerless. If this is case, have the car transported to a work- shop to have the problem rectified.


93U SM 06.book Page 176 Friday, February 18, 2005 1:15 PM


176


Starting and driving


(cid:127) The car may feel weak but can be driven carefully to a workshop to have the prob- lem rectified.


(cid:127) Drivability may barely be affected. Irrespective of the drivability of the car, the car must be taken to a workshop to have the problem checked and rectified.


Temporary override of Park Brake Shift Lock


NOTICE


Due to electrical problems it may not be possible to move the selector lever out of the park position, even if the ignition is ON. If for some reason the selector lever has to be moved out of the park position (i.e. to tow the car a short distance) do as described below.


1 Apply the parking brake. 2 Lift up the rubber mat in the storage compartment ahead of the selector lever.


3 Under the floor of the storage compart- ment is a yellow plastic lever. Use a thin tool, such as a screwdriver, to press and hold the plastic lever while moving the selector lever from P to N.


4 Remove the tool. 5 Release the parking brake if the car is to


be moved immediately, otherwise it should remain on.


Check fuse 6 in the engine bay fuse box. If the fuse is OK the battery may be dead. Contact a workshop to have the problem checked and rectified. We recommend that you contact a Saab dealer.


Temporary override of Park Brake Shift Lock


93U SM 06.book Page 177 Friday, February 18, 2005 1:15 PM


Selector lever positions


The selector lever is locked and the transmission is mechanically blocked. The engine can be started. To move the selector lever out of the P position, depress the brake pedal and press in the detent (catch) on the selector lever. Only select the park position (P) when the car is stationary.


Only select the reverse position (R) when the car stationary. The detent release button must be pressed before the selector lever can be moved to R. Wait until reverse gear has engaged before touching the accelerator.


Starting and driving


177


You must press the brake pedal to move the selector lever from the neutral position (N). In neutral, the transmission is disengaged from the engine. The engine can be started but make sure the parking brake is on to prevent unexpected movement. To prevent the engine and transmission becoming hotter than necessary, select N for long stops with the engine running, e.g. when stuck in a traffic jam. At traffic lights, leave the selector lever in the drive position (D).


The drive position (D) is the normal one for forward driving. The transmission shifts automatically between all gears from 1st to 5th, the timing of which depends on factors such as the current accelerator position and the speed of the car. Pause for a moment before applying the acce- lerator, to allow the gears to engage.


93U SM 06.book Page 178 Friday, February 18, 2005 1:15 PM


178


Starting and driving


Sentronic, manual gear selection Move the selector lever to the manual position (M) (to the left position D) to select gear manually. Select a higher gear by pressing the selector lever forward or a lower gear by pulling it back. The selector lever will return to a position adjacent to the letter M after each gear change. An example of when you may wish to make manual gear changes is when overtaking, to enable you to remain in a low gear for an extended period of time. If the road surface is slippery, you may wish to start off in 2nd or 3rd to reduce the risk of wheel spin. When descending steep hills you should select a low gear to increase the braking effect of the engine and thus spare the brakes.


Steering wheel controls for manual gear selection3


Manual gear selections are displayed on the main instrument panel. The letter M and the current gear are displayed. When the selector lever is in the M position, as opposed to the D position, the engine is much more responsive to changes in accel- erator position. The accelerator has a different feel. When changing down, the desired gear can be selected but the transmission will not change down until the engine speed is low enough to avoid overrevving.


Certain variants also have steering wheel controls for manual gear selection. On these models, it is possible to change gear manually using the selector lever and the steering wheel controls. The steer- ing wheel controls are only active when the selector lever is in the M position. Select a higher gear by pressing the right-hand button and a lower gear by pressing the left-hand button.


93U SM 06.book Page 179 Friday, February 18, 2005 1:15 PM


Cruise control (Cruise control system)


WARNING


Do not use the cruise control system in wet or icy conditions, in dense traffic or on winding roads.


For safety reasons (brake system func- tion), the brakes must be applied once when the engine has started, before the cruise control system can be activated. The following message is shown on the SID:


Tap brakes lightly before using cruise control.


Starting and driving


179


To set the desired speed 1 Slide the switch to ON. 2 Move the thumbwheel up to SET/+ or SET/– when the car has reached the desired speed (above 15 mph (25 km/ h)).


To increase the preset speed You can increase the speed in any of the following ways: (cid:127) Accelerate to the desired speed. Jog the


control to SET/+ or SET/–.


(cid:127) Jog the control to SET/+ to increase the


speed by 1 mph (1.6 km/h) (when cruise control already engaged).


(cid:127) Hold the control in the SET/+ position until


the desired speed is reached (when cruise control already engaged).


Cruise control switches


The system has the following functions: 1 ON: engaged 2 OFF: disengaged 3 SET/+: sets the speed and increases


the set speed


4 SET/ –: sets the speed and decreases


the set speed


5 RESUME: re-engages the system at the


set speed


The CRUISE indicator light in the main instrument panel comes on when the switch is slid to ON. If you switch off the engine while the cruise control is ON, the system will be ON the next time the engine is started.


93U SM 06.book Page 180 Friday, February 18, 2005 1:15 PM


180


Starting and driving


To reduce the preset speed You can reduce speed in any of the follow- ing ways: (cid:127) Brake to the desired speed. Jog the


control to SET/+ or SET/–.


(cid:127) Jog the control to SET/– to reduce the


speed by 1 mph (1.6 km/h).


(cid:127) Hold the control in the SET/– position until


the desired speed is reached.


Temporary increase in speed Accelerate, without shifting down (manual transmission), to exceed the set speed such as for overtaking. When you release the accelerator, the car will return to the set speed. To disengage the system temporarily Slide the switch to the left towards OFF, but only as far as to disengage the cruise con- trol. Allow the switch to spring back.


To re-engage the system Slide the switch to RESUME. The car will return to the previously set speed. Vehicle speed must exceed 15 mph (25 km/h). To disengage the system The system will be disengaged: (cid:127) As soon as the brake or clutch pedal is depressed (cars with manual transmis- sion).


(cid:127) When the switch is slid towards OFF. See also heading "To disengage the system temporarily".


(cid:127) When the switch is slid to OFF. (cid:127) When the TCS/ESP system is operative. (cid:127) When position N is selected (cars with


automatic transmission).


Braking It is good practice to try your brakes period- ically while driving. This is particularly important when driving in heavy rain, on roads with a lot of surface water, in snow or in salty slush. In such conditions a slight delay in the braking effect may be noticed. To minimize this delay, dry the brakes by applying them lightly now and again. This should also be done after the car has been washed, and in extremely damp weather. To avoid the brakes becoming overheated, such as when negotiating long descents with a drop of several hundred yards (hun- dred metres), select a low gear to utilize the braking effect of the engine. If the car has automatic transmission, select 1st or 2nd gear. You can help to prolong the life of the brakes by thinking ahead and braking harder over short periods, rather than braking more moderately over long stretches.


Starting and driving


181


The brake system provides Electronic Brakeforce Distribution (EBD). This distri- butes the brake pressure between the front and rear wheels, in such a way as to achieve optimum braking performance irrespective of the car’s speed or load. The ABS has a built-in diagnostics function which will switch on the ABS warning light if a fault is detected in the system (see page 84). The following message will appear on the SID (and corresponding symbol on main instrument unit) if a fault is detected:


Antilock brake malfunction. Contact Saab dealer.


93U SM 06.book Page 181 Friday, February 18, 2005 1:15 PM


WARNING


ABS brakes


(cid:127) It is prudent to try your brakes from


time to time, especially when driving in heavy rain, through water collected on the road, in snow, on a wet road surface or in salty slush. In such condi- tions, the brakes may take longer than normal to take effect. To rectify this, touch the brake pedal periodically to dry the brakes out.


(cid:127) The same applies after the car has


been washed or when the weather is very humid.


(cid:127) Avoid parking the car with wet brakes. Before parking, and if the traffic condi- tions allow, brake quite heavily so that the brake discs and pads warm up and dry.


(cid:127) The brakes are power assisted and it should be kept in mind that the servo unit only provides the power assis- tance when the engine is running.


(cid:127) The brake pressure required when the


engine is off, (e.g. when the car is being towed) is roughly four times the normal pedal force required. The pedal also feels hard and unrespon- sive.


(cid:127) Overheating can cause the brakes to


fade!


WARNING


(cid:127) The additional safety afforded by the ABS system is not designed to allow drivers to drive faster but to make normal driving safer.


(cid:127) To stop as quickly as possible, without


loss of directional stability, whether the road surface is dry, wet or slippery, press the brake pedal down hard without letting up (do not pump the pedal), declutching simulta- neously, and steer the car to safety.


The Antilock Braking System (ABS) modu- lates the brake pressure to each wheel. The pressure is automatically reduced just before the wheel locks up and then increases again to the point at which the wheel is just about to lock. The wheel sen- sors send information to the brake system’s electronic control module for every 4 or so inches (decimetre) that the car rolls. This information is processed continuously to ensure that the adjustment of the brake pressure will be as exact as possible. Adjustment takes place up to 12 times per second.


93U SM 06.book Page 182 Friday, February 18, 2005 1:15 PM


182


Starting and driving


The ABS system will not reduce the braking distance on loose gravel, snow or ice but, because the wheels cannot lock up, steer- ing control is retained. When the ABS system operates you will feel the brake pedal pulsate and hear a ticking noise, both of which are perfectly normal. Apply the brake pedal with full force (you cannot press too hard), declutch and if nec- essary steer to safety. Do not release the brake pedal before the car has come to a halt or the danger is past! The above is critical. If the road is slippery, the ABS system will operate even when only light pressure is applied to the brake pedal. This means that the driver can brake gently to test the condi- tion of the road and adapt their driving accordingly. It is well worth practising the use of ABS brakes on a skid pan or other suitable facility.


Braking with ABS brakes. Indication that the system is operating: pulsating brake pedal and ticking noise


Braking with ABS – evasive steering


93U SM 06.book Page 183 Friday, February 18, 2005 1:15 PM


Hill Start Assist (HSA) 3


(Hillstarting assistance) This function facilitates starting on a hill. When the parking brake has been released and the foot is moved off the brake pedal it can take approx. 1.5 s before the brakes release. The brakes release as soon as the accelerator pedal is depressed within this time.


Traction Control System (TCS) Anti-spin system


WARNING


When driving normally, the TCS system helps to improve the car’s directional stability. The TCS must not be regarded as a system to enable the driver to main- tain higher speeds. The same precau- tions must be adopted as normal for safe cornering and driving on slippery roads.


How the system works The Traction Control System (TCS) is designed to prevent wheelspin. This enables the car to achieve the best possible grip and, hence, maximum tractive effort, together with greater stability. The TCS uses information from the ABS wheel sensors to detect when the front (driv- ing) wheels are rotating faster then the rear wheels. If the two front wheels are rotating faster than the rear wheels, the torque from the engine is reduced to eliminate the differ- ence. The process continues until all the wheels are rotating at the same speed. The advantages of the TCS become most apparent when the cohesion between the front wheels and the road surface is so low


Starting and driving


183


that one or both of the wheels would lose their grip were the car not equipped with the TCS, e.g.: (cid:127) When the car is pulling away or accelerat-


ing with the front wheels on different surfaces (e.g. one slippery and one dry), the TCS functions like an electronic differ- ential lock, making sure that both wheels rotate at the same speed. The system also functions when the car is reversing. (cid:127) When cornering, if the inside front wheel


rotates faster than the other wheels.


TCS OFF


lights up under the speedometer if:


(cid:127) a fault has been detected and the system


has therefore been switched off there is a fault in the ABS system the system has been switched off manually.


(cid:127) (cid:127) 93U SM 06.book Page 184 Friday, February 18, 2005 1:15 PM


184


Starting and driving


TCS button


TCS indicator When the remote control is turned to the ON position, the lamp is lit for about 4 seconds while the system performs self-diagnosis.


light under the speedometer


The comes on when the TCS is operative, that is when one of the wheels has lost its grip. The fact that the TCS is operative indicates that the limit for grip has been exceeded and that the driver must exercise greater care.


Turning the TCS off The TCS is switched on automatically when the engine is started. You can switch the system off manually with light the TCS button, whereupon the under the speedometer will come on. The TCS cannot be switched off if the car is trav- elling faster than 35 mph (60 km/h). It may be necessary to switch off the system if the car has become bogged down, for instance. Press TCS to switch it on again. If a fault is detected in the ABS, the TCS will be switched off automatically. The following message is shown on the SID:


Traction control failure. Contact Saab dealer.


The cruise control system (if active) will automatically be disengaged if the TCS is operative.


93U SM 06.book Page 185 Friday, February 18, 2005 1:15 PM


Electronic Stability Program (ESP) 3
Anti-skid system


WARNING


When driving normally, the ESP system helps to improve the car’s directional stability. The ESP must not be regarded as a system to enable the driver to main- tain higher speeds. The same precau- tions must be adopted as normal for safe cornering and driving on slippery roads must be adopted.


The Electronic Stability Program employs both the antilock braking system (ABS) and the traction control system (TCS). It is a system that helps the driver to stabilize the car in unusual circumstances that can oth- erwise be difficult to handle.


Starting and driving


185


How the ESP system works The Electronic Stability Program can help to prevent the car from skidding by braking one or several wheels independently of the driver. The engine output is then also reduced to prevent the driving wheels from spinning. The car has sensors that measure wheel speed, yaw rate, lateral acceleration, steering wheel position and braking pres- sure. The values provided by these sensors are used to calculate the actual direction of the car, the intentions of the driver and whether the ESP should be engaged. If this direction does not agree with that intended by the driver, calculated from the steering wheel position, the ESP is engaged. The ESP improves the driver’s chances of retaining control over the car in a critical situation.


Illustration of how the system applies the brakes on one or several wheels in order to reduce the likelihood of the car skidding


93U SM 06.book Page 186 Friday, February 18, 2005 1:15 PM


186


Starting and driving


ESP button


ESP OFF


lights up under the speedometer if:


(cid:127) a fault has been detected and the system


has therefore been switched off the system has been switched off manually


ESP indicator light When the remote control is turned to the ON position, the lamp is lit for about 4 seconds while the system performs self-diagnosis.


light under the speedometer


The comes on for a short period of time when the ESP system is operative. Operation of the ESP indicates reduced cohesion between the tires and the road, and that extra care should be taken by the driver. Turning ESP system off The system can be turned off manually with the ESP button, whereupon the light under the speedometer will come on. The car must be travelling slower than 35 mph (60 km/h). The TCS is also disengaged. The ESP is always engaged during braking, even if it has been switched off manually with the ESP button.


If a fault is detected in the system, the following message will be displayed on the SID:


Stability control failure. Contact Saab dealer.


The cruise control system (if active) will automatically be disengaged if the ESP is operative.


NOTICE


Changes to the chassis, such as a change of wheels, shock absorbers or springs, could affect the function of the ESP system. Always consult a workshop before chang- ing any chassis components. We recom- mend that you contact a Saab dealer.


(cid:127) Starting and driving


187


Parking


WARNING


(cid:127) Never leave children or pets unat- tended in the car. In warm, sunny weather, the temperature inside the car can reach 160–180°F (70–80°C). (cid:127) Park where the vehicle will not create


an obstruction or a hazard to other road users.


(cid:127) Do not park on dry grass or other


combustible material. The catalytic converter gets very hot and could start a fire.


(cid:127) Apply the parking brake, remove the


remote control and lock the car.


Correct hold


If the parking brake is applied when the car starts off, the following message will appear on the SID:


Release parking brake.


93U SM 06.book Page 187 Friday, February 18, 2005 1:15 PM


Parking brake


WARNING


(cid:127) Always apply the parking brake when


you park the car. If the car is to be left parked for a long time, refer to page 189.


(cid:127) Always apply the parking brake


before removing the remote control. (cid:127) Do not use the parking brake while


driving.


(cid:127) Grasp the parking brake lever in such a way that no fingers get trapped when you release the parking brake.


indicator light on the main instru-


The parking brake lever is situated between the front seats. The brake acts on the rear wheels. When the parking brake is applied, the ment panel will come on. To release the parking brake, lift the lever slightly, pull the release button on the under- side of the lever and lower the lever. If conditions allow, it is best if the brake pedal is not depressed, or only depressed as little as necessary so as to stop the car from rolling, when the parking brake is applied. To facilitate releasing the parking brake, depress the brake pedal. This is especially appropriate if the car is standing on a hill.


93U SM 06.book Page 188 Friday, February 18, 2005 1:15 PM


188


Starting and driving


NOTICE


Empty the car yourself and bear in mind: (cid:127) Never leave a mobile phone, camera, computer or similar object visible in the car.


(cid:127) Clothing, packages and bags attract


thieves.


(cid:127) Do not leave small objects such as CDs, sunglasses and coins visible.


(cid:127) If possible, park in a well-lit, conspicu-


ous parking space.


(cid:127) Thieves strike whenever and wher- ever they are given the opportunity.


Parking on a hill When parking on a steep hill, turn the front wheels so that they will be blocked by the curb if the car should move. If the car is parked with one front wheel touching the curb, for example, you may need to turn the steering wheel slightly when you insert the remote control to allow the steering wheel lock to unlock.


1 Downhill with curb.


Turn the wheels toward the curb and edge the car forwards until the wheel lightly touches the curb.


2 Uphill with curb. Turn


the wheels away from the curb and edge the car backward until the wheel lightly touches the curb.


3 Uphill or downhill with- out curb. Turn the wheel towards the edge of the road so that the car, should it move, will not roll towards the middle of the road.


Starting and driving


189


93U SM 06.book Page 189 Friday, February 18, 2005 1:15 PM


Long-term parking If the car is not going to be used for some time, e.g. three to four months, the following steps are recommended: (cid:127) Drain the washer fluid reservoir and


hoses.


(cid:127) Wash and wax the car. Clean the rubber seals on the hood, trunk lid and doors, and lubricate them with glycerol (glycerine).


(cid:127) After washing the car, dry the brake discs to avoid corrosion by taking the car out on the road and applying the brakes a few times.


(cid:127) Fill the fuel tank to prevent condensation


forming in it.


(cid:127) Top up the coolant and check the anti-


freeze before the onset of winter.


(cid:127) Park the car in a dry, covered and well- ventilated building. Leave the parking brake OFF!


(cid:127) Convertible: If the car is stored, the soft


top should be closed. If necessary, use wheel chocks and leave the parking brake off.


(cid:127) Disconnect the negative (–) battery lead. If frost is likely to occur during the storage period, remove the battery and store it in a frost-free place. If it is not possible to stand the car on axle stands, increase the tire pressure to 43 psi (3 bar).


Leave all the door windows open a crack and cover the car with a non-plastic tarpaulin – not one made of plastic which will not breath.


(cid:127) (cid:127) 93U SM 06.book Page 190 Friday, February 18, 2005 1:15 PM


Starting and driving


190
Saab Parking Assistance 3
Saab Parking Assistance


WARNING


Responsibility always lies with the driver when reversing. (cid:127) The parking assistance system can


facilitate parking and reversing.


(cid:127) Bear in mind that small objects, such


as a child lying on the ground, and narrow objects cannot always be detected by the system.


Saab Parking Assistance facilitates parking and reversing. There are four sensors in the rear bumper that detect objects up to 6 ft (1.8 meters) behind the car. If the car is heavily laden, the system may falsely indicate that there is an object within the detection range. This is since the sen- sors are angled towards the ground when the car is tail-heavy.


Area monitored by the sensors seen from the side


Area monitored by the sensors seen from above


The system uses four sensors in the rear bumper. These emit ultrasound signals that bounce back to the sensors off any objects behind the car. The system, however, cannot always detect small or narrow objects, such as a post, since the surface area presented to the car is too small.


The system is activated automatically when reverse is engaged or selected. Audible confirmation is given and the following text is shown on the SID:


Parking assistance active


If a warning message, such as the seatbelt reminder, is shown on the SID when reverse is engaged, the audible signals from the parking assistance system will not be heard since the warning message has priority. When the sensors detect an object within the monitored area, pulses of sound (- - - -) will be heard. The frequency of these pulses increases as the car comes closer to the object.


93U SM 06.book Page 191 Friday, February 18, 2005 1:15 PM


If you stop the car with reverse gear engaged, the sound pulse will stop after 2 seconds. The sound pulses will return if you continue to reverse. If the car rolls for- ward while reverse is engaged, the system is silenced. When the distance to the object is less than 1 ft. (30 cm), a continuous tone will be heard. When an object is approximately 3 ft. (90 cm) from the car, the sound pulses change character markedly (frequency increases). A distance of about 3 ft. (90 cm) is suitable if you wish to load or unload the trunk. If the distance between an object and a corner sensor does not change for 3 seconds, for example if you are reversing alongside a wall, the system will switch to monitoring straight back. The system indi- cates if the distance to the wall decreases again. If a trailer is hitched up and correctly con- nected to the trailer contact by the tow bar, the system is automatically deactivated.


Starting and driving


191


Cars with trailer hitch If the car has a trailer hitch and its wiring is correctly connected to the car’s electrical system, the Saab Parking Assistance auto- matically compensates for the protrusion of the tow bar. If a camper or trailer is hitched up and the trailer hitch wiring is correctly connected to the car’s electrics, the system is automati- cally deactivated. You can temporarily deactivate the Saab Parking Assistance as follows: (cid:127) Engage reverse and press the CLEAR


button on the SID control panel.


The system will be reactivated the next time you engage reverse.


NOTICE


The sensors must be kept clean to func- tion well. Ice, snow and dirt can affect their sensitivity. Large quantities of snow or dirt covering the sensors can prevent the parking assistance system from detecting any objects. Do not spray the sensors with a pressure washer, as this can damage them.


Reversing alongside a wall If the distance between an object and a corner sensor does not change for 2 seconds, for example if you are reversing alongside a wall, the system will switch to monitoring straight back. The system indi- cates if the distance to the wall decreases again.


93U SM 06.book Page 192 Friday, February 18, 2005 1:15 PM


192


Starting and driving


Error messages If the system malfunctions, the following message will appear on the SID:


Parking assistance malfunction. Contact Saab dealer.


If the system is subject to interference, the following message will be shown on the SID:


Parking assistance sensor interference.


If this message appears, clean the sensors. The sensors are located in the black trim on the rear bumper


The system can be switched off using Profiler. 1 Press the CUSTOMIZE button to go to


Profiler.


2 Select Park Assistance using the


INFO dial.


3 Press in the INFO dial. 4 Select SPA on or SPA off. 5 Confirm this selection by pressing the


INFO dial.


Park Assistance


SPA on SPA off


Explanation of SPA on and SPA off.


SPA on


Saab Parking Assistance is activated automatically when reverse is engaged. The system warns of objects behind the car. If a trailer is hitched up and correctly connected to the trailer connector, the system will be deactivated automati- cally. You can also deactivate the sys- tem temporarily with the CLEAR button if reverse has been engaged and the system is active.


SPA off


Saab Parking Assistance deactivated.


93U SM 06.book Page 193 Friday, February 18, 2005 1:15 PM


Economical driving Factors affecting fuel consumption The fuel consumption of a car is greatly affected by driving conditions, climate, road conditions, speed, driving technique, etc. Breaking-in Fuel consumption may be somewhat higher during the break-in period (the first 3,000–4,000 miles (5,000–7,000 km)). Weather conditions Summer temperatures give better fuel economy than winter ones. The difference can be as much as about 10%. Consump- tion increases in cold weather because the engine takes longer to reach its normal operating temperature. The transmission and wheel bearings also take longer to warm up. Even distance affects consump- tion: short journeys of 3–5 miles (5–8 km) do not give the engine enough time to reach its optimum temperature. Wind con- ditions also have a marked effect on fuel consumption.


How to read the diagram: If fuel consumption with the engine at normal temperature is 28 mpg (10 l/ 100 km), the actual fuel consumption 3 miles (5 km) after the engine has started from cold will be: – 23.5 mpg (12 l/100 km) at outside temp.


of 68°F (+20°C) (increase of 20%).


– 17.7 mpg (16 l/100 km) at outside temp.


of 32°F (0°C) (increase of 60%).


– 14 mpg (20 l/100 km) at outside temp.


of –4°F (–20°C) (increase of 100%).


It is clear from the diagram that both dis- tance driven and outside temperature have a significant impact on fuel consumption, after a cold start. If the car is normally driven on short jour- neys, 3–5 miles (5–8 km), for example to and from work, the average consumption will be 60–80% above the normal level.


Starting and driving


193


Percentage increase in fuel consumption of engine starting from cold compared to engine at normal temperature.


Driving techniques (cid:127) To obtain the best running economy, with regard to fuel consumption and general wear, the car must be serviced regularly.


(cid:127) High speed, unnecessary acceleration,


frequent braking and much changing down all give higher fuel consumption.


(cid:127) Frequent gear changing in traffic, starting in cold weather, the use of studded tires and roof racks, and towing a camper all increase fuel consumption.


(cid:127) Do not warm up the engine while the car


is stationary. If idling, the engine will take much longer to reach its optimum temperature, and


93U SM 06.book Page 194 Friday, February 18, 2005 1:15 PM


194


Starting and driving


engine wear is at its greatest during this period. Drive off as soon as possible after starting the engine and avoid high engine speeds.


(cid:127) Drive as smoothly and thoughtfully as


possible. Match your driving to the prevail- ing traffic conditions.


(cid:127) Driving in a low gear gives rise to higher fuel consumption than driving in a high gear because of the higher engine speed for any given road speed. Always shift up as soon as traffic conditions allow and drive in the highest gear as much as possible.


(cid:127) Check the tire pressure once a month.


Incorrect tire pressure increases tire wear. It is preferable for the tire pressure to be slightly high than too low. Under- pressure increases fuel consumption.


(cid:127) Check the fuel consumption regularly.


Increased fuel consumption can indicate that something is wrong and that the car needs to be checked. We recommend that you contact a Saab dealer.


Practical road tests have demonstrated that substantial savings in fuel consumption can be made if the above advice is followed.


WARNING


Never switch off the engine while driving as the effect of the brakes and power steering will be greatly reduced.


Road conditions Wet roads increase fuel consumption, as do unpaved roads and driving in hilly country (the amount of fuel saved driving downhill is less than the additional amount required to climb the hill).


Engine block heater 3
The following are just some of the benefits to the car and the environment of using an engine block heater: (cid:127) Lower fuel consumption. (cid:127) Reduced wear on the engine. Inside of car warms up faster.


(cid:127) Exhaust emissions substantially reduced


over short runs.


The engine heater is effective at outside temperatures up to 60–70°F (+15–+20°C). The warmer it is outside, the shorter the time the engine heater needs to be connected. Longer than 1.5 hours is unnecessary. If the car is equipped with a removable, electric cabin heater that is not in use, store this in the trunk.


(cid:127) Starting and driving


195


93U SM 06.book Page 195 Friday, February 18, 2005 1:15 PM


Driving in cold weather In cold weather, special attention should be paid to the following: (cid:127) Before driving off, make sure that the


wiper blades have not frozen to the wind- shield.


(cid:127) Remove any snow from the heating


system air intakes between the hood and the windshield. If necessary, inject oil into the locks to prevent them from freezing. Use molyb- denum-sulphide oil (MoS2). If the locks freeze, exercise care when unlocking the car (manual unlocking) to avoid breaking the key. Warm up the key or use a de-icer. It is particularly important when the roads are slippery that the brakes and tires are in good condition.


(cid:127) For how to check the level of antifreeze in


the engine coolant, see page 222.


(cid:127) Add gasoline anti-freeze when refueling several times before the onset of winter. This will prevent condensation water in the fuel tank from freezing and causing interruptions in the fuel supply. The likeli- hood of condensation is lowest when the fuel tank is full. If the car is parked outside and the temperature is below zero, gasoline anti- freeze is of little use as it cannot remove water that has already frozen. Park the car in a warm place so that any ice that may have built up melts, then add gaso- line anti-freeze when refueling.


Condensation is caused by temperature fluctuations, either in the outside temper- ature alone or when the car is alternately parked outdoors and in a garage.


(cid:127) Convertible: Avoid operating the soft top


at temperatures below 23°F (–5°C).


(cid:127) The car is equipped with tires designed to provide optimum grip on both wet and dry roads, although this has been achieved at the expense of somewhat reduced grip on snow and ice. For regular driving on snow and ice, we therefore recommend that winter tires be fitted. However, winter tires achieve this extra grip at the expense of grip on bare road surfaces.


Winter tires, particularly studded tires, gen- erally make driving safer on snow and ice. Acquaint yourself with the legal provi- sions governing the use of different types of winter tires and snow chains. Studded tires are not allowed in some countries. If winter tires are fitted, the same type must be fitted to all four wheels. Your Saab dealer will be pleased to advise you on the best tires for your car.


(cid:127) (cid:127) 93U SM 06.book Page 196 Friday, February 18, 2005 1:15 PM


196


Starting and driving


Remember that tires age: it may therefore be necessary to change winter tires before they reach the legal wear limit, as they grad- ually lose their friction properties with age. If you get into a front wheel skid and the car has a manual transmission, the best response is to freewheel, which means declutching so that the wheels neither drive nor brake, and to cautiously steer in the desired direction. If the car has automatic transmission, ease off the accelerator slightly and steer cau- tiously in the desired direction. If you get into a rear wheel skid, steer in the same direction as the movement of the rear of the car.


Driving with tire chains 3
Snow chains must only be fitted to the wheel and tire dimensions that Saab recommends in "Technical data" on page 293. We recommend that you contact a Saab dealer regarding approved tire chains. See also page 263.


WARNING


(cid:127) Do not drive at speeds above 30 mph (50 km/h) when tire chains are fitted.


(cid:127) Tire chains can reduce directional


stability.


(cid:127) Do not fit tire chains to the car’s rear


wheels.


NOTICE


(cid:127) Check the links frequently for wear. (cid:127) Check that the chains do not foul the


wheel arch liner at full lock.


(cid:127) Refer to the "Technical data" section


on page 293, for information on wheel and tire dimensions approved for the fitting of tire chains.


Starting and driving


197


93U SM 06.book Page 197 Friday, February 18, 2005 1:15 PM


Driving in hot climates Always check the coolant level before start- ing a journey. When the engine is cold, the coolant must not lie above the KALT/COLD mark on the expansion tank (boundary between the upper and lower sections of the tank). At the end of a journey, allow the engine to idle for 2–3 minutes before switching it off. If the needle on the temperature gauge enters the red zone, the following message will be shown on the SID:


Hot engine. Make a safe stop. Run engine on idle.


1 Stop the car but do not switch off the


engine. Do not remove the cap on the cooling system expansion tank, even if the tank is empty. The engine tempera- ture should decrease. If the temperature continues to rise with the engine idling, the engine must be switched off.


2 If the engine is idling and the needle on the temperature gauge falls, wait until a normal temperature is shown (about in the middle of the scale) before switching off the engine. If the coolant needs to be topped up, carefully unscrew the expansion tank cap. Fill as required with a mixture of 50 % antifreeze and 50 % clean water. Use an antifreeze approved by Saab.


WARNING


(cid:127) Exercise care when opening the hood


if the engine is overheated. Never remove the expansion tank cap completely when the engine is hot. (cid:127) The cooling system is pressurized - hot coolant and vapour can escape. These can cause injury to your eyes and burns. Open the cap slowly to release the pressure before removing it.


3 Have the car’s cooling system checked. We recommend that you contact a Saab dealer.


93U SM 06.book Page 198 Friday, February 18, 2005 1:15 PM


Starting and driving


198
Towing a trailer 3


WARNING


(cid:127) Do not drive with a trailer on inclines steeper than 15 %. The load on the drive (front) wheels will be so low that the wheels can start to spin and prevent further progress.


(cid:127) In addition, the car’s parking brake


may not always be sufficient to hold the car and trailer securely, as the wheels may start to slide.


(cid:127) Always apply the trailer’s parking


brake when unhitching it. There is otherwise a risk of personal injury or damage to the bumper should the trailer start to roll.


(cid:127) When you hitch up the trailer be sure to attach its safety chains to the holes by the hitch.


Make sure you are familiar with the legal requirements regarding speed limits for towing, maximum trailer weights, trailer braking requirements, and also any spe- cial driving licence provisions.


Trailer hitch attachment 3
Trailer hitch attachments are available as accessories. These are designed for a max- imum trailer weight of 3500 lbs (1588 kg), with trailer brakes. An electrical connection 3 for the towbar and an electrical unit are provided in the electrical centre on the left-hand side of the luggage compartment. The Saab genuine electrical socket enables a battery in the trailer on tow to be charged while driving. Also, if the car has SPA, this is deactivated automatically if a trailer is hitched up and correctly connected to the Saab genuine trailer socket. Saab recommendations: (cid:127) Use a genuine Saab trailer hitch that is


designed and tested for your Saab.


(cid:127) Contact your Saab dealer for advice on


which trailer hitch is designed for your car.


93U SM 06.book Page 199 Friday, February 18, 2005 1:15 PM


NOTICE


(cid:127) We recommend you to use a genuine Saab trailer hitch, since other models can damage the car’s bodywork and electrical system.


(cid:127) We recommend that you contact a


Saab dealer for guidance on how to connect a trailer hitch.


(cid:127) Exercise care when driving on uneven roads or against the curb if the car is heavily laden. This particularly applies to cars with 17" wheels.


Recommendations for cars with automatic transmission The following driving time limits are based on the capacity of the cooling system in hot weather, i.e. approximately 86°F (+30°C). Gradient of hill, %


Time limit, minutes


Max. trailer weight, lbs. (kg) 3330 (1500) unlimited 3080 (1400) max. 15
2645 (1200) max. 15
2200 (1000) max. 15


6-8
9-11
12-14
max. 15


The following driving time limits are based on the capacity of the cooling system in hot weather, i.e. approximately 104°F (+40°C). Gradient of hill, %


Time limit, minutes


Max. trailer weight, lbs. (kg) 2200 (1000) unlimited 1760 (800) max. 15
1100 (500) max. 15
880 (400) max. 15


6-8
9-11
12-14
max. 15


When negotiating long hills, bear the follow- ing important considerations in mind. Rises in coolant temperature are indicated by the temperature gauge in the main instru- ment panel. The following steps are taken in order as the temperature of the transmission increases: (cid:127) Gear change pattern is altered (cid:127) A/C compressor is switched off (cid:127) Max. engine torque is reduced


Starting and driving


199


The following message will be displayed on the SID if the transmission fluid becomes too hot:


Gearbox too hot. Make a safe stop. Open hood to cool down.


If this message appears, stop the car as soon as it is safe to do so and allow the engine to idle until the message has gone out. The selector lever should be in position P. When continuing your journey, manually select a low gear in which the engine speed is about 3,500 rpm until the incline eases (see page 178).


WARNING


Remember to use engine-braking (selec- tor position M1, M2, or M3) to spare the brakes when you are driving on a long or steep downhill slope. Overheating can cause the brakes to fade!


93U SM 06.book Page 200 Friday, February 18, 2005 1:15 PM


200


Starting and driving


Recommendations for cars with manual transmission Rises in coolant temperature are indicated by the temperature gauge in the main instru- ment panel. When the needle is just outside the red zone, the A/C compressor will be switched off and, on certain engine variants, the max- imum engine torque will be limited. When continuing your journey, select a low gear in which the engine speed is about 3,500 rpm until the incline eases.


WARNING


Remember to use engine-braking (selec- tor position 1, 2, or 3) to spare the brakes when you are driving on a long or steep downhill slope. Overheating can cause the brakes to fade!


Trailer hitch load The weight distribution on the trailer makes a lot of difference to the handling properties of the car and trailer combination. With a two-wheel trailer, concentrate the load over the wheels and keep it as low as possible. The trailer should be loaded so that the load on the towball is 110–165 lbs. (50–75 kg). Note that this load must be included in the total load for the car. If this now exceeds the specified load capacity, the load in the trunk may have to be reduced by the correspond- ing amount.


Distribution of load in trailer a Light b Moderate c Heavy


Starting and driving


201


Reversing Get someone to help you keep an eye out behind the trailer as the door mirrors do not always provide sufficient rearward vision when reversing.


Driving considerations Always take extra care when towing a trailer, as the car’s handling will be different and its braking performance reduced. The trailer’s braking system and suspension also have a considerable effect on these characteristics. See also "Driving with a load" on page 204. Drive carefully: (cid:127) descending hills (cid:127) on uneven roads (cid:127) over railway crossings (cid:127) when meeting large vehicles If the car has automatic transmission, select gear M1 when ascending or descending steep hills.


93U SM 06.book Page 201 Friday, February 18, 2005 1:15 PM


Checks before driving Make sure that the car and trailer are in good working order. This is essential since towing a trailer increases the strain on the car. (cid:127) Check and if necessary adjust the tire


pressure of the car and trailer.


(cid:127) Make sure all wheel bolts are properly


tightened.


(cid:127) Make sure that the equipment joining the


car and trailer is properly secured and adjusted.


(cid:127) Make sure the trailer’s electrical cable is


properly connected and is not so long that it drags along the ground. Also, make sure the cable is not too short and risks break- ing when turning a corner.


(cid:127) Check all bulbs. (cid:127) Check the car and trailer brakes. (cid:127) Make sure that all items on or in the


camper or trailer are properly secured.


(cid:127) Make sure that the trailer’s jockey wheel is


raised and locked.


(cid:127) Check the distribution of the load so that


the car and trailer are well balanced.


(cid:127) Check that the rearview mirrors provide


the best possible rearward vision.


(cid:127) Make sure the trailer’s safety cable is


correctly attached.


93U SM 06.book Page 202 Friday, February 18, 2005 1:15 PM


Starting and driving


202
Driving with a roof rack load


WARNING


(cid:127) A roof load will affect the car’s center


of gravity and aerodynamics. Be aware of this when cornering and driv- ing in crosswinds.


(cid:127) Adjust your speed to the prevailing


conditions.


(cid:127) Due to higher aerodynamics drag, fuel economy may suffer when driving with a roof rack.


The maximum permissible roof load is 220 lbs. (100 kg). Note that the roof load must be included in the car’s maximum per- missible payload and axle load. Strong, sturdy roof carriers designed spe- cially for your car are available from your Saab dealer. Always secure roof loads securely.


Fitting roof carriers 3


Sport Sedan and SportCombi without roof rails 1 Open the four covers on the roof of the


car.


2 Insert a screw with washer into each roof carrier foot. Fit a seal onto each screw. 3 The roof carriers are marked front and


back.


4 Bolt the roof carriers to the brackets in


the roof.


5 Check that the roof carriers are firmly


mounted.


Mounting holes for roof carrier


Starting and driving


203


93U SM 06.book Page 203 Friday, February 18, 2005 1:15 PM


Fitting roof carriers 3


SportCombi with roof rails 1 Clean the car’s roof rails. 2 Check the markings on the cross


members to see which is the front and which is the rear roof carrier.


3 Place the cross members on the roof rails, on their respective sides of the centre supports. The cross members must not be placed beyond the front or rear joint on the rail. Ensure that the distance between the cross members is at least 700 mm. If a roof box is to be fitted, the cross members must be positioned so that the tailgate can be opened fully without hitting the roof box.


4 Using your thumb, press the bracket


so that it lies snugly against the outside of the roof rail. Make sure that the roof carriers are seated centrally on the rubber spacers and that these sit correctly on the roof rail. Pull the spacers down slightly on the inside of the roof rail.


5 Centre the roof carriers so that they


protrude equally on both sides.


6 Tighten the roof carriers by hand.


Ensure that the tightening knobs are upright once the roof carriers have been tightened.


7 Make sure the roof carriers are securely


in place.


Driving with the trunk lid open


WARNING


Avoid driving with the trunk lid partly or fully open, since exhaust fumes can be drawn into the cabin.


If you must drive with the trunk lid open, close all windows and the sunroof (if equipped) and set the cabin fan to its high- est speed setting.


Driving in deep water


NOTICE


Do not drive in puddles or water deeper than 7 in. (20 cm) and do not drive faster than 3–4 mph. Water can otherwise be sucked into the engine. The engine will be seriously damaged if water enters the intake system.


93U SM 06.book Page 204 Friday, February 18, 2005 1:15 PM


Starting and driving


204
Driving with a load The handling characteristics are affected by how the car is loaded.


NOTICE


(cid:127) Place the heaviest load as far forward


and as low as possible in the trunk. (cid:127) Secure the load to the lashing eyes


(see page 149).


(cid:127) Heavy loads mean that the car’s


center of gravity is further back. As a result, the car will sway more during evasive steering.


(cid:127) Never exceed the permissible load of the roof box, even if there is room for more.


(cid:127) Ensure that the tire pressure is correct – slight overinflation is preferable to underinflation.


(cid:127) The braking distance of a loaded car is always greater. Keep your distance from the vehicle in front.


(cid:127) Do not exceed the car’s permissible


gross vehicle weight or axle load (see page 294).


(cid:127) Roof loads can negatively affect tele-


communication.


For further information on tires see page 256.


93U SM 06.book Page 205 Friday, February 18, 2005 1:15 PM


Driving at night Bear in mind the following points, especially when driving at night: (cid:127) Nighttime driving requires your full


concentration


(cid:127) Do not rush. Count on your journey taking


slightly longer.


(cid:127) The number of drivers under the influence of drugs is likely to be greater at night than during the day.


(cid:127) Do not stare at the headlights of oncom-


ing vehicles.


(cid:127) Avoid driving at night if you have poor


eyesight. Night vision deteriorates with age.


(cid:127) Keep your car’s headlights, windows and mirrors clean. Also, if you wear glasses, make sure they are clean.


(cid:127) Make sure you are well rested before


starting a long journey. Take a break every other hour.


(cid:127) Only eat light meals. Heavy meals have a


tendency to induce tiredness.


(cid:127) Wild animals prefer to move at dusk and


dawn.


(cid:127) Check the headlight levelling setting (see


page 102).


Towing the car


Front towing eye


Starting and driving


205


WARNING


(cid:127) Make sure that the towing eye is


screwed in tightly. It has a left-hand thread!


(cid:127) The towing eye is only designed for


towing the car on roads. It must not be used to pull the car out of a ditch, for example.


(cid:127) Make sure that all bystanders keep a suitable distance, in case the towing eye or tow rope should snap. The towing eye or tow rope could catapult off and cause seriously injury.


(cid:127) Never drive with the towing eye fitted


to the front bumper. Return it to its designated storage space.


WARNING


(cid:127) Remember that the brake servo does


not operate when the engine is off. Much greater pressure than normal will therefore be required to operate the brake pedal.


(cid:127) Nor does the steering servo operate when the engine is off. The steering will therefore be much heavier than usual.


(cid:127) The towing vehicle should always be


heavier than the vehicle on tow.


(cid:127) Never allow passengers to ride in the


car when it is on tow.


(cid:127) Always seek professional help if the


car needs to be recovered.


(cid:127) The ignition switch must be in the ON position if the car is moved with the engine not running.


(cid:127) The steering wheel lock must be


disengaged before towing the car.


(cid:127) The steering wheel lock disengages when the remote control is inserted into the ignition switch, if the battery has sufficient charge.


93U SM 06.book Page 206 Friday, February 18, 2005 1:15 PM


206


Starting and driving


Front towing eye fitted. The towing eye has a left-hand thread!


Rear towing eye


Never use the towing eyes to pull the car unstuck.


The front towing eye is stowed by the spare wheel. On the left-hand side of the bumper is a cover concealing the attachment point (tapped hole) for the towing eye. 1 Press the knob on the upper section of this cover at the same time as pulling out the lower edge.


2 Screw in the towing eye. The towing


eye has a left-hand thread!


3 Insert the wheel wrench into the eye to


tighten it properly.


To refit the cover: Start by inserting the top edge of the cover. Then click in the lower edge, one corner at a time.


Rear towing eye The car has a permanent towing eye at the rear under the bumper. If the car is equipped with a towbar, this can be used instead of the towing eye.


Towing the car


NOTICE


Never use the towing eyes to pull the car unstuck.


Engage neutral (automatic transmission: move the selector lever to N). Turn on the parking lights. Drive carefully and do not exceed the speed limit for vehicles on tow.


Starting and driving


207


Transporting the car


NOTICE


If a car with sports (lowered) chassis is transported, for example on a flat bed truck, take extra care not to damage the spoiler and/or underbody.


93U SM 06.book Page 207 Friday, February 18, 2005 1:15 PM


Always try to keep the towrope taut by gently applying the brake of the car on tow, as necessary. This will avoid the towrope being jerked violently.


Cars with automatic transmission:


NOTICE


(cid:127) The car must be towed front first. (cid:127) If the car is to be towed with the front wheels off the ground, make sure the parking brake is off, as this acts on the rear wheels.


Always observe the speed limit for vehicles on tow. Whatever the speed limit, the car must not be towed at speeds exceeding 30 mph (50 km/h) nor for a distance of more than 30 miles (50 km). If the car needs to be transported over a longer distance, a tow truck or flatbed truck must be called out. The engine cannot be started by towing or pushing the car. In an emergency, the engine can be started as described under "Jump starting" on page 208.


Attachment points for anchorage straps


Vehicle recovery If the car has to be transported on a flatbed truck, or similar, it must be securely strapped down. There are attachment points for this purpose on the underside of the car. The attachment points are oblong hole that have been reinforced to cope with the stresses that arise during this type of transport.


93U SM 06.book Page 208 Friday, February 18, 2005 1:15 PM


Starting and driving


208
Driving with the compact spare tire


WARNING


(cid:127) Do not exceed 50 mph (80 km/h). The tire can overheat affecting the car’s roadholding.


(cid:127) Tire pressure: refer to page 304. (cid:127) The spare tire or punctured tire must be stowed under the trunk floor, and secured in place with the retaining nut.


Observe the following when the compact spare tire is fitted: (cid:127) The compact spare is light and easy to


handle when changing a tire.


(cid:127) Do not drive further than necessary with the compact spare fitted - the maximum life of the tire is only just over 2,000 miles (approx. 3,500 km).


(cid:127) Refit the standard tire as soon as possi-


ble.


Important considerations when driving with a compact spare tire: (cid:127) The car’s ground clearance is reduced. (cid:127) The car must not be driven with more than


one compact spare tire at a time.


(cid:127) Avoid driving against the curb. (cid:127) Do not use snow chains. (cid:127) Do not fit the wheel cover - this would


conceal the warning text.


NOTICE


To avoid damaging a alloy wheel of a punctured tire, this can be temporarily placed outside up in the spare wheel well but only while driving to the closest work- shop. As a general rule, all heavy loads must be well secured in the trunk (see page 149).


Jump starting


WARNING


(cid:127) When working on the battery, highly explosive gas can build up. A spark could ignite this gas that collects around the battery. Therefore, always avoid sparks and open flames in the vicinity of the battery.


(cid:127) The battery contains corrosive sulphu- ric acid. Always wear a face mask or goggles when working on the battery.


(cid:127) If battery acid gets into the eyes or


splashes onto skin or clothing, wash the affected area liberally with water. If acid gets into the eyes or a large quan- tity makes contact with the skin, seek medical help.


93U SM 06.book Page 209 Friday, February 18, 2005 1:15 PM


NOTICE


NOTICE


Starting and driving


209


Ignoring these steps could result in costly damage to your vehicle that would not be covered by your warranty. Trying to start your car by pushing or pull- ing it could damage your vehicle, even if you have a manual transmission. If you have an automatic transmission, your vehicle cannot be started by pushing or pulling it.


It is essential when a donor battery is to be used to jump start the car that the jump leads be connected correctly to prevent arcing. To jump start your vehicle: 1 Check the other vehicle. It must have a 12-volt battery with a negative ground system.


If the other system is not a 12-volt system with a negative ground, both vehicles can be damaged.


2 Get the vehicles close enough so the


jumper cables can reach, but be sure the vehicles are not touching each other. If a poor connection on the negative jumper cable should exist, it is possible for damage to be caused to electrical systems/components of either vehicle should inadvertent contact be made. You would not be able to start your car and bad grounding could damage the electrical systems.


WARNING


You could be injured if the vehicles roll. Set the parking brake firmly on each vehi- cle. Put an automatic transmission in P (Park) or a manual transmission in Neutral.


3 Turn off the ignition on both vehicles.


Turn off lights that are not needed, and radios. This will avoid sparks and help save both batteries and it could save your radio.


Jump starting


NOTICE


If you leave your radio on, it could be badly damaged. The repairs would not be covered by your warranty.


4 Open the hood and locate the battery. Find the positive (+) and negative (–) termi- nals on the battery.


WARNING


An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.


93U SM 06.book Page 210 Friday, February 18, 2005 1:15 PM


210


Starting and driving


WARNING


Using a match or flame of any kind near a battery can cause battery gas to explode. You can suffer burns or be blinded. Use a flashlight if you need more light. Be sure the electrolyte in the battery is not frozen. Discharged batteries will freeze. When connecting jumper cables to a frozen battery, gas from the chemical reaction inside the battery can build up under the ice and cause an explosion. Battery fluid contains acid that can burn you. Do not get it on you. If you acciden- tally get it in your eyes or on your skin, flush the area with water and get medical help immediately.


5 Check that the jumper cables do not


have loose or missing insulation. If they do, you could get a shock and also the vehicles could be damaged. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) and negative (–) will go to negative (–). Do not connect (+) to (–) or you will get a short that could injure you or would damage the battery and maybe other parts as well.


6 Connect the red positive (+) cable to the positive (+) terminal of the vehicle with the discharged battery.


7 Do not let the other end touch metal.


Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.


8 Now connect the negative (–) cable to


the good battery’s negative terminal.


9 Attach the cable to the discharged


battery’s negative terminal.


10 Start the vehicle with the good battery


and run the engine for a while. 11 Try to start the vehicle with the


discharged battery. If it does not start after a few tries, it probably needs service. Note. If the current in the low battery is too low it might be necessary to wait several minutes with the cables connected before you can start the engine with the low battery.


12 Remove the cables in reverse order to prevent electrical shorting. Take care that they do not touch each other or any other metal.


Using a battery charger 3/starter unit To avoid damaging the car’s electrical system and electronics, the following rules must be followed when charging the battery or jump starting the car.


If the charger or starter unit can be set to different voltages (6V/12V/18V/24V), 12V must be selected.


(cid:127) Follow the manufacturer’s instructions


supplied with the charger or starter unit. (cid:127) No other apparatus that are grounded or


connected to the mains must be connected to the car during charging or jump starting.


(cid:127) The charger or starter unit must under no


conditions produce a voltage greater than: (cid:127) 16V continuous (cid:127) 18V for 60 min.


If you are unsure about the charge rating of the unit, disconnect the battery clamp from the positive terminal before connecting the unit to the battery.


(cid:127) Starting and driving


211


93U SM 06.book Page 211 Friday, February 18, 2005 1:15 PM


For long trips Before starting off on a long journey, it is advisable to have your car inspected by your Saab dealer. Obtain a few important items to take along on your journey, such as spare bulbs, wiper blades, fuses, a drive belt (poly-V-belt) and the like. You can check some points yourself before- hand: (cid:127) Check that no oil or fuel leaks out of the


Loading...
x