2007 Nissan Quest Owners Manual

pressure warning light OFF. If you have a flat tire, replace it with a spare tire as soon as possible.

c Although you can continue driving with a punctured MichelinT PAXT tire (if so equipped), remember that vehicle han- dling stability is reduced, which could lead to an accident and personal injury. Also, driving a long distance at high speeds may damage the tires.

c Do not drive at speeds above 50 MPH (80 km/h) and do not drive more than 125 miles (200 km) with a punctured MichelinT PAXT tire (if so equipped). The actual distance the vehicle can be driven on a flat tire depends on outside temperature, vehicle load, road condi- tions and other factors.

c Do not tow a trailer when a MichelinT

PAXT (if so equipped) tire is flat.

c When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

c Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.

c Do not inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors.

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

CHANGING A FLAT TIRE If you have a flat tire, follow the instructions be- low. Stopping the vehicle 1. Safely move the vehicle off the road and

away from traffic.

2. Turn on the hazard warning flashers.

3. Park on a level surface and apply the parking

brake. Shift the transmission into P (Park).

4. Turn off the engine.

5. Raise the hood to warn other traffic and to signal professional road assistance person- nel that you need assistance.

6. Have all passengers get out of the vehicle and stand in a safe place, away from traffic and clear of the vehicle.

WARNING

c Make sure the parking brake is securely applied and the automatic transmission is shifted into P (Park).

c Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous.

c Never change tires if oncoming traffic is close to your vehicle. Wait for profes- sional road assistance.

WCE0044

Blocking wheels Place suitable blocks s1 at both the front and back of the wheel diagonally opposite the flat tire s2 to prevent the vehicle from moving when it is jacked up.

WARNING

Be sure to block the wheel as the vehicle may move and result in personal injury.

In case of emergency 6-3

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

6. Turn the retainer counterclockwise and re-

move the spare tire.

Removing wheel cover (if so equipped)

CAUTION

Do not use your hands to pry off wheel caps or wheel covers. Doing so could re- sult in personal injury.

Use caution not to scratch the wheel cover or wheel surface.

LCE0078

Getting the spare tire and tools 1. Tip up the passenger side second row cap- tain(cid:146)s chair. Refer to (cid:147)Tip up for easy entry to 3rd row(cid:148) in the (cid:147)Safety (cid:151) seats, seat belts and supplemental restraint system(cid:148) section of this owner(cid:146)s manual.

2. Lift up the floor carpeting and remove the

jack.

6-4 In case of emergency

LCE0079
3. Stow the center tray table (if so equipped).

4. Move both front seats as forward as pos-

sible.

5. Lift up the floor carpeting s1 . Remove the

spare tire cover s2 and jack tool kit.

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

c Use the correct jack-up points. Never use any other part of the vehicle for jack support.

c Never jack up the vehicle more than

necessary.

c Never use blocks on or under the jack. c Do not start or run the engine while vehicle is on the jack. It may cause the vehicle to move. This is especially true for slip differentials.

vehicles

limited

with

c Do not allow passengers to stay in the

vehicle while it is on the jack.

c Never run the engine with a wheel(s) off the ground. It may cause the vehicle to move.

WSD0085

Jacking up vehicle and removing the damaged tire

WARNING

c Never get under the vehicle while it is supported only by the jack. If it is nec- essary to work under the vehicle, sup- port it with safety stands.

c Use only the jack provided with your vehicle to lift the vehicle. Do not use the jack provided with your vehicle on other vehicles. The jack is designed for lifting only your vehicle during a tire change.

In case of emergency 6-5

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

Always refer to the proper illustrations for the correct placement and jack-up points for your specific vehicle model and jack type. Carefully read the caution label attached to the jack body and the following instruc- tions.

1. Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut wrench. Do not remove the wheel nuts until the tire is off the ground.

6-6 In case of emergency

WCE0081
2. Place the jack directly under the jack-up point as illustrated so the top of the jack contacts the vehicle at the jack-up point. Align the jack head between the two notches in the front or the rear as shown. Also fit the groove of the jack head between the notches as shown. The jack should be used on firm and level ground.

3. To lift the vehicle, securely hold the jack lever and rod with both hands. Carefully raise the vehicle until the tire clears the ground. Re- move the wheel nuts, and then remove the tire.

WCE0056

Installing the spare tire The spare tire is designed for emergency use. See specific instructions under the heading (cid:147)Wheels and tires(cid:148) in the (cid:147)Mainte- nance and do-it-yourself(cid:148) section of this manual.

1. Clean any mud or dirt from the surface be-

tween the wheel and hub.

2. Carefully put the spare tire on and tighten

the wheel nuts finger tight.

3. With the wheel nut wrench, tighten wheel nuts alternately and evenly as illustrated until they are tight.

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

4. Lower

the vehicle slowly until

the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely in the sequence illustrated (sA , sB , sC , sD , sE ). Lower the vehicle completely.

WARNING c Incorrect wheel nuts or

improperly tightened wheel nuts can cause the wheel to become loose or come off. This could cause an accident.

c Do not use oil or grease on the wheel studs or nuts. This could cause the nuts to become loose.

c Retighten the wheel nuts when the ve- hicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).

As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench.

Wheel nut tightening torque:

83 ft-lb (112 N•m)

The wheel nuts must be kept tightened to specification at all is recom- mended that wheel nuts be tightened to specifications at each lubrication interval.

times.

It

c The spare tire is designed for emer- gency use. See specific instructions un- der the heading (cid:147)Wheels and tires(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) section of this manual.

Adjust tire pressure to the COLD pressure.

COLD pressure: After vehicle has been parked for three hours or more or driven less than 1 mile (1.6 km).

COLD tire pressures are shown on the Tire and Loading Information label affixed to the driver side center pillar.

After adjusting tire pressure to the COLD tire pressure, the display of the tire pres- sure information may show higher pres- sure than the COLD tire pressure after the vehicle has been driven more than 1 mile (1.6 km). This is because the tire pressur- izes as the tire temperature rises. This does not indicate a system malfunction.

5. Securely store the flat tire and jacking equip-

ment in the vehicle.

WARNING

c Always make sure that the spare tire and jacking equipment are properly se- cured after use. Such items can become dangerous projectiles in an accident or sudden stop.

In case of emergency 6-7

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

c Whenever working on or near a battery, always wear suitable eye protectors (for example, goggles or industrial safety spectacles) and remove rings, metal bands, or any other jewelry. Do not lean over the battery when jump starting.

c Do not attempt to jump start a frozen battery. It could explode and cause se- rious injury.

c Your vehicle has an automatic engine cooling fan. It could come on at any time. Keep hands and other objects away from it.

JUMP STARTING

To start your engine with a booster battery, the instructions and precautions below must be fol- lowed.

WARNING

c If done incorrectly, jump starting can lead to a battery explosion, resulting in severe injury or death. It could also damage your vehicle.

c Explosive hydrogen gas is always present in the vicinity of the battery. Keep all sparks and flames away from the battery.

c Do not allow battery fluid to come into contact with eyes, skin, clothing or painted surfaces. Battery fluid is a cor- rosive sulfuric acid solution which can cause severe burns. If the fluid should come into contact with anything, imme- diately flush the contacted area with water.

c Keep battery out of

children.

the reach of

c The booster battery must be rated at 12
volts. Use of an improperly rated battery can damage your vehicle.

6-8 In case of emergency

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

WARNING

Always follow the instructions below. Failure to do so could result in damage to the charging system and cause personal injury.

1.

If the booster battery is in another vehicle, position the two vehicles to bring their bat- teries near each other. Do not allow the two vehicles to touch.

2. Apply the parking brake. Shift the transmis- sion into P (Park). Switch off all unnecessary electrical systems (lights, heater, air condi- tioner, etc.).

WCE0054
3. Remove vent caps on the battery (if so equipped). Cover the battery with an old cloth to reduce explosion hazard.

4. Connect jumper cables in the sequence il-

lustrated (sA , sB , sC , sD ).

CAUTION

c Always connect positive (1) to positive (1) and negative (2) to body ground (for example, strut mounting bolt, engine lift bracket, etc.) (cid:151) not to the battery.

c Make sure the jumper cables do not touch moving parts in the engine com- partment and that the cable clamps do not contact any other metal.

5. Start the engine of the booster vehicle and

let it run for a few minutes.

6. Keep the engine speed of the booster ve- hicle at about 2,000 rpm, and start the en- gine of the vehicle being jump started.

CAUTION

Do not keep the starter motor engaged for more than 10 seconds. If the engine does not start right away, turn the key off and wait 3 to 4 seconds before trying again.

7. After starting the engine, carefully discon- nect the negative cable and then the positive cable.

8. Replace the vent caps (if so equipped). Be sure to dispose of the cloth used to cover the vent holes as it may be contaminated with corrosive acid.

In case of emergency 6-9

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

PUSH STARTING

IF YOUR VEHICLE OVERHEATS

CAUTION

Automatic transmission models cannot be push-started or tow-started. Attempt- ing to do so may cause transmission damage.

6-10 In case of emergency

If your vehicle is overheating (indicated by an extremely high temperature gauge reading), or if you feel a lack of engine power, detect abnormal noise, etc. take the following steps.

WARNING

c Do not continue to drive if your vehicle overheats. Doing so could cause engine damage or a vehicle fire.

c To avoid the danger of being scalded, never remove the radiator cap while the engine is still hot. When the radiator cap is removed, pressurized hot water will spurt out, possibly causing serious injury.

c Do not open the hood if steam is com-

ing out.

1. Move the vehicle safely off the road, apply the parking brake and move the shift lever to P (Park). Do not stop the engine.

2. Turn off the air conditioner. Open all the windows, move the heater or air conditioner temperature control to maximum hot and fan control to high speed.

3. Get out of the vehicle. Look and listen for steam or coolant escaping from the radiator before opening the hood. (If steam or cool- ant is escaping, turn off the engine.) Do not open the hood further until no steam or coolant can be seen.

4. Open the engine hood.

WARNING

If steam or water is coming from the en- gine, stand clear to prevent getting burned.

5. Visually check drive belts for damage or looseness. Also check if the cooling fan is running. The radiator hoses and radiator should not leak water. If coolant is leaking, the water pump belt is missing or loose, or the cooling fan does not run, stop the en- gine.

WARNING

Be careful not to allow your hands, hair, jewelry or clothing to come into contact with, or get caught in, engine belts or the engine cooling fan. The engine cooling fan can start at any time when the coolant temperature is high.

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

For information about towing your vehicle behind a recreational vehicle (RV), refer to (cid:147)Flat towing(cid:148) in the (cid:147)Technical and consumer information(cid:148) sec- tion of this manual.

6. After the engine cools down, check the cool- ant level in the engine coolant reservoir tank with the engine running. Add coolant to the engine coolant reservoir tank if necessary. Have your vehicle repaired at a NISSAN dealer.

TOWING YOUR VEHICLE

When towing your vehicle, all State (Provincial in Canada) and local regulations for towing must be followed. Incorrect towing equipment could dam- age your vehicle. Towing instructions are avail- able from a NISSAN dealer. Local service opera- tors are generally familiar with the applicable laws and procedures for towing. To assure proper towing and to prevent accidental damage to your vehicle, NISSAN recommends having a service operator tow your vehicle. It is advisable to have the service operator carefully read the following precautions:

WARNING

c Never ride in a vehicle that is being

towed.

c Never get under your vehicle after it has

been lifted by a tow truck.

CAUTION

c When towing, make sure that the trans- mission, axles, steering system and powertrain are in working condition. If any unit is damaged, dollies must be used.

c Always attach safety chains before

towing.

In case of emergency 6-11

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

(cid:150) Turn the ignition key to the OFF po- sition, and secure the steering wheel in a straight-ahead position with a rope or similar device. Never secure the steering wheel by turning the ig- nition key to the LOCK position. This may damage the steering lock mechanism.

(cid:150) Move the gearshift lever to the N

(Neutral) position.

c When towing automatic with the rear wheels on the ground (if you do not use towing dollies): Always release the parking brake.

WSD0087

CAUTION

c Never

tow automatic transmission models with the front wheels on the ground or four wheels on the ground (forward or backward), as this may cause serious and expensive damage to the transmission. If it is necessary to tow the vehicle with the rear wheels raised always use towing dollies under the front wheels.

c When towing with the front wheels on

towing dollies:

WSD0086

TOWING RECOMMENDED BY NISSAN NISSAN recommends that your vehicle be towed with the driving (front) wheels off the ground or place the vehicle on a flat bed truck as illustrated.

6-12 In case of emergency

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

CAUTION

c Tow chains or cables must be attached only to the main structural members of the vehicle or the towing hooks (if so equipped). Otherwise, the vehicle body will be damaged.

c Do not use the vehicle tie downs to free a vehicle stuck in sand, snow, mud, etc. Never tow the vehicle using the vehicle tie downs or recovery hooks.

c Always pull the cable straight out from the front or rear of the vehicle. Never pull the vehicle at an angle.

c Pulling devices should be routed so they do not touch any part of the sus- pension, steering, brake or cooling systems.

c Pulling devices such as ropes or canvas straps are not recommended for use in vehicle towing or recovery.

If your vehicle is stuck in sand, snow, mud, etc., use the following procedure:

1. Turn off the Vehicle Dynamic Control System

(if so equipped).

2. Make sure the area in front and behind the

vehicle is clear of obstructions.

WCE0120
VEHICLE RECOVERY (freeing a stuck vehicle) Front

WARNING

c Stand clear of a stuck vehicle. c Do not spin your tires at high speed. This could cause them to explode and result in serious injury. Parts of your vehicle could also overheat and be damaged.

3. Turn the steering wheel right and left to clear

an area around the front tires.

4. Slowly rock the vehicle forward and back-

ward. c Shift back and forth between R (Reverse)

and D (Drive).

c Apply the accelerator as little as possible

to maintain the rocking motion.

c Release the accelerator pedal before shifting between R (Reverse) and D (Drive).

c Do not spin the tires above 35 mph (55

km/h).

5.

If the vehicle can not be freed after a few tries, contact a professional towing service to remove the vehicle.

In case of emergency 6-13

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

MEMO

6-14 In case of emergency

7 Appearance and care

Cleaning exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Waxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Removing spots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Underbody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Aluminum alloy wheels . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Chrome parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Tire dressings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

Cleaning interior. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Floor mats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Corrosion protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5

Most common factors contributing to vehicle corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Environmental factors influence the rate of corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
To protect your vehicle from corrosion . . . . . . . . . . . . 7-5

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

CLEANING EXTERIOR

In order to maintain the appearance of your ve- hicle, it is important to take proper care of it.

To protect the paint surfaces, please wash your vehicle as soon as you can: c after a rainfall to prevent possible damage

from acid rain.

c after driving on coastal roads. c when contaminants such as soot, bird drop- pings, tree sap, metal particles or bugs get on the paint surface.

c when dust or mud builds up on the surface. Whenever possible, store or park your vehicle inside a garage or in a covered area.

When it is necessary to park outside, park in a shady area or protect the vehicle with a body cover. Be careful not to scratch the paint surface when putting on or removing the body cover. WASHING Wash dirt off with a wet sponge and plenty of water. Clean the vehicle thoroughly using a mild soap, a special vehicle soap or general purpose dishwashing liquid mixed with clean, lukewarm (never hot) water. 7-2 Appearance and care

CAUTION

c Do not wash the vehicle with strong household soap, strong chemical deter- gents, gasoline or solvents.

c Avoid using tight-napped or

c Do not wash the vehicle in direct sun- light or while the vehicle body is hot, as the surface may become water-spotted. rough cloths, such as washing mitts. Care must removing caked-on dirt or other foreign sub- stances so the paint surface is not scratched or damaged.

taken when

be

Rinse the vehicle thoroughly with plenty of clean water. Inside flanges, seams and folds on the doors, hatches and hood are particularly vulnerable to the effects of road salt. Therefore, these areas must be cleaned regularly. Take care that the drain holes in the lower edge of the door are open. Spray water under the body and in the wheel wells to loosen the dirt and wash away road salt. A damp chamois can be used to dry the vehicle to avoid water spots.

WAXING Regular waxing protects the paint surface and helps retain new vehicle appearance. Polishing is recommended to remove built-up wax residue and to avoid a weathered appearance before re-applying wax. A NISSAN dealer can assist you in choosing the proper product. c Wax your vehicle only after a thorough wash- ing. Follow the instructions supplied with the wax.

c Do not use a wax containing any abrasives, cutting compounds or cleaners that may damage the vehicle finish.

Machine compounding or aggressive polishing on a base coat/clear coat paint finish may dull the finish or leave swirl marks. REMOVING SPOTS Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store.

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

c Wipe off excess tire dressing using a dry towel. Make sure the tire dressing is com- pletely removed from the tire tread/grooves. c Allow the tire dressing to dry as recom-

mended by tire dressing manufacturer.

UNDERBODY In areas where road salt is used in winter, it is necessary to clean the underbody regularly in order to prevent dirt and salt from building up and causing the acceleration of corrosion on the un- derbody and suspension. Before the winter pe- riod and again in the spring, the underseal must be checked and, if necessary, retreated. GLASS Use glass cleaner to remove smoke and dust film from the glass surfaces. It is normal for glass to become coated with a film after the vehicle is parked in the hot sun. Glass cleaner and a soft cloth will easily remove this film.

CAUTION

When cleaning the inside of the windows, do not use sharp-edged tools, abrasive cleaners or chlorine-based disinfectant cleaners. They could damage the electri- cal conductors, radio antenna elements or rear window defroster elements.

ALUMINUM ALLOY WHEELS Wash the wheels regularly, especially during win- ter months in areas where road salt is used. If not removed, road salt can discolor the wheels. CHROME PARTS Clean all chrome parts regularly with a non- abrasive chrome polish to maintain the finish. TIRE DRESSINGS NISSAN does not recommend the use of tire dressings. Tire manufacturers apply a coating to the tires to help reduce discoloration of the rub- ber. If a tire dressing is applied to the tires, it may react with the coating and form a compound. This compound may come off the tire while driving and stain the vehicle paint. If you choose to use a tire dressing, take the following precautions: c Use a water-based tire dressing. The coat- ing on the tire dissolves more easily with an oil-based tire dressing.

c Apply a light coat of tire dressing to help prevent tire tread/grooves (where it would be difficult to remove).

from entering

the

it

Appearance and care 7-3

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

c Never use fabric protectors unless rec-

ommended by the manufacturer.

c Do not use glass or plastic cleaner on meter or gauge lens covers. It may dam- age the lens cover.

FLOOR MATS The use of genuine NISSAN floor mats can ex- tend the life of your vehicle carpet and make it easier to clean the interior. No matter what mats are used, be sure they are fitted for your vehicle and are properly positioned in the footwell to prevent interference with pedal operation. Mats should be maintained with regular cleaning and replaced if they be- come excessively worn.

CLEANING INTERIOR

Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft bristled brush. Wipe the vinyl and leather surfaces with a clean, soft cloth damp- ened in mild soap solution, then wipe clean with a dry, soft cloth.

Regular care and cleaning is required in order to maintain the appearance of the leather.

Before using any fabric protector, read the manu- facturer(cid:146)s recommendations. Some fabric pro- tectors contain chemicals that may stain or bleach the seat material.

Use a cloth dampened only with water to clean the meter and gauge lens.

CAUTION

c Never use benzine, thinner or any simi-

lar material.

c Small dirt particles can be abrasive and damaging to leather surfaces and should be removed promptly. Do not use saddle soap, car waxes, polishes, oils, cleaning fluids, solvents, deter- gents or ammonia-based cleaners as they may damage the leather(cid:146)s natural finish.

7-4 Appearance and care

WAI0006
Floor mat positioning aid (driver(cid:146)s side only) This vehicle includes a front floor mat bracket to act as a floor mat positioning aid. NISSAN floor mats have been specially designed for your ve- hicle model. The driver(cid:146)s side floor mat has a grommet hole incorporated in it. Position the mat by placing the floor mat bracket hook through the floor mat grommet hole while centering the mat in the footwell. Periodically check to make certain the mats are properly positioned.

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely in the shade before using them. See (cid:147)Seat belt maintenance(cid:148) in the (cid:147)Safety (cid:150) Seats, seat belts and supplemen- tal restraint system(cid:148) section of this manual.

WARNING

Do not allow wet seat belts to roll up in the retractor. NEVER use bleach, dye or chemical solvents to clean the seat belts, since these materials may severely weaken the seat belt webbing.

CORROSION PROTECTION

MOST COMMON FACTORS CONTRIBUTING TO VEHICLE CORROSION c The accumulation of moisture-retaining dirt and debris in body panel sections, cavities, and other areas.

c Damage to paint and other protective coat- ings caused by gravel and stone chips or minor traffic accidents.

ENVIRONMENTAL FACTORS INFLUENCE THE RATE OF CORROSION Moisture Accumulation of sand, dirt and water on the ve- hicle body underside can accelerate corrosion. Wet floor coverings will not dry completely inside the vehicle, and should be removed for drying to avoid floor panel corrosion. Relative humidity Corrosion will be accelerated in areas of high relative humidity, especially those areas where the temperatures stay above freezing and where atmospheric pollution exists and road salt is used.

Temperature High temperatures accelerate the rate of corro- sion to those parts which are not well ventilated. Air pollution Industrial pollution, the presence of salt in the air in coastal areas, or heavy road salt use acceler- ates the corrosion process. Road salt also accel- erates the disintegration of paint surfaces. TO PROTECT YOUR VEHICLE FROM CORROSION c Wash and wax your vehicle often to keep the

vehicle clean.

c Always check for minor damage to the paint

and repair it as soon as possible.

c Keep drain holes at the bottom of the doors

open to avoid water accumulation.

c Check the underbody for accumulation of sand, dirt or salt. If present, wash with water as soon as possible.

CAUTION

c NEVER remove dirt, sand or other de- bris from the passenger compartment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom.

Appearance and care 7-5

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

c Never allow water or other liquids to come in contact with electronic compo- nents inside the vehicle as this may damage them.

Chemicals used for road surface de-icing are extremely corrosive. They accelerate corrosion and deterioration of underbody components such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders. In winter, the underbody must be cleaned periodically. For additional protection against rust and corro- sion, which may be required in some areas, con- sult a NISSAN dealer.

7-6 Appearance and care

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

8 Maintenance and do-it-yourself

Maintenance requirements. . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
General maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Explanation of general maintenance items . . . . . . . . . 8-2
Maintenance precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
Engine compartment check locations . . . . . . . . . . . . . . . . 8-6
Engine cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
Checking engine coolant level . . . . . . . . . . . . . . . . . . . 8-7
Changing engine coolant . . . . . . . . . . . . . . . . . . . . . . . . 8-8
Engine oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
Checking engine oil level . . . . . . . . . . . . . . . . . . . . . . . . 8-8
Changing engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Changing engine oil filter . . . . . . . . . . . . . . . . . . . . . . . 8-10
5-speed automatic transmission fluid . . . . . . . . . . . . . . . 8-11
Power steering fluid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12
Window washer fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12
Window washer fluid reservoir . . . . . . . . . . . . . . . . . . 8-12
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-13
Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14
Drive belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15
Spark plugs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15
Replacing spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . 8-15

Air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
In-cabin microfilter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16
Windshield wiper blades . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
Brake Pedal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20
Parking brake and brake pedal . . . . . . . . . . . . . . . . . . . . . 8-20
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-20
Engine compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20
Passenger compartment . . . . . . . . . . . . . . . . . . . . . . . 8-21
Battery replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23
Keyfob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-24
Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24
Fog lights (if so equipped) . . . . . . . . . . . . . . . . . . . . . . 8-24
Exterior and interior lights. . . . . . . . . . . . . . . . . . . . . . . 8-26
Wheels and tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-30
Tire pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-30
Tire labeling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-34
Types of tires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-37
Tire chains. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-39
Changing wheels and tires . . . . . . . . . . . . . . . . . . . . . 8-40

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

MAINTENANCE REQUIREMENTS

GENERAL MAINTENANCE

Your new NISSAN has been designed to have minimum maintenance requirements with longer service intervals to save you both time and money. However, some day-to-day and regular maintenance is essential to maintain your NIS- SAN(cid:146)s good mechanical condition, as well as its emission and engine performance.

It is the owner(cid:146)s responsibility to make sure that the scheduled maintenance, as well as general maintenance, is performed.

As the vehicle owner, you are the only one who can ensure that your vehicle receives proper maintenance. You are a vital link in the mainte- nance chain. Scheduled maintenance

For your convenience, both required and optional scheduled maintenance items are described and listed in your (cid:147)NISSAN Service and Maintenance Guide.(cid:148) You must refer to that guide to ensure that necessary maintenance is performed on your NISSAN at regular intervals. General maintenance

General maintenance includes those items which should be checked during normal day-to-day op- eration. They are essential for proper vehicle op- eration. It is your responsibility to perform these maintenance procedures regularly as prescribed. 8-2 Maintenance and do-it-yourself

Performing general maintenance checks requires minimal mechanical skill and only a few general automotive tools. These checks or inspections can be done by you, a qualified technician, or, if you prefer, a NISSAN dealer. Where to go for service If maintenance service is required or your vehicle appears to malfunction, have the systems checked and corrected by a NISSAN dealer. NISSAN technicians are well-trained specialists who are kept up-to-date with the latest service information through technical bulletins, service tips, and in-dealership training programs. They are completely qualified to work on NISSAN ve- hicles before they work on your vehicle, rather than after they have worked on it. You can be confident that a NISSAN dealer(cid:146)s service department performs the best job to meet the maintenance requirements on your vehicle (cid:151) in a reliable and economical way.

During the normal day-to-day operation of the vehicle, general maintenance should be per- formed regularly as prescribed in this section. If you detect any unusual sounds, vibrations or smells, be sure to check for the cause or have a NISSAN dealer do it promptly. In addition, you should notify a NISSAN dealer if you think that repairs are required.

When performing any checks or maintenance work, closely observe the (cid:147)Maintenance precau- tions(cid:148) later in this section. EXPLANATION OF GENERAL MAINTENANCE ITEMS information on the following Additional items with (cid:147)*(cid:148) is found later in this section. Outside the vehicle The maintenance items listed here should be performed from time to time, unless otherwise specified. Doors and engine hood Check that the doors and engine hood operate properly. Also ensure that all latches lock securely. Lubricate hinges, latches, latch pins, rollers and links as necessary. Make sure that the secondary latch keeps the hood from opening when the primary latch is released.

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

When driving in areas using road salt or other corrosive materials, check lubrication frequently. Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Road wheel nuts* When checking the tires, make sure no wheel nuts are missing, and check for any loose wheel nuts. Tighten if necessary. Tire rotation* Tires should be rotated every 7,500 miles (12,000 km). Tires* Check the pressure with a gauge often and always prior to long distance trips. If neces- sary, adjust the pressure in all tires, including the spare, to the pressure specified. Check carefully for damage, cuts or excessive wear. Wheel alignment and balance If the vehicle should pull to either side while driving on a straight and level road, or if you detect uneven or abnormal tire wear, there may be a need for wheel alignment. If the steering wheel or seat vibrates at normal highway speeds, wheel balancing may be needed. c For additional

information regarding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Safety Information(cid:148) (Canada) in the Warranty Information Booklet .

Windshield Clean the windshield on a regular basis. Check the windshield at least every six months for cracks or other damage. Have a dam- aged windshield repaired by a qualified repair facility. Windshield wiper blades* Check for cracks or wear if they do not wipe properly. Inside the vehicle The maintenance items listed here should be checked on a regular basis, such as when per- forming periodic maintenance, cleaning the ve- hicle, etc. Additional information on the following items with an (cid:147)*(cid:148) is found later in this sec- tion.

Accelerator pedal Check the pedal for smooth operation and make sure the pedal does not bind or require uneven effort. Keep the floor mat away from the pedal. Automatic transmission P (Park) position mechanism On a fairly steep hill check that your vehicle is held securely with the selector lever in the P (Park) position without applying any brakes. Brake pedal* Check the pedal for smooth op- eration and keep the floor mat away from the pedal.

Brakes Check that the brakes do not pull the vehicle to one side when applied. Parking brake Confirm that your vehicle is held securely on a fairly steep hill with only the parking brake applied. Seats Check seat position controls such as seat adjusters, seatback recliner, etc. to ensure they operate smoothly and all latches lock securely in every position. Check that the head restraints move up and down smoothly and the locks (if so equipped) hold securely in all latched positions. Seat belts Check that all parts of the seat belt system (for example, buckles, anchors, adjusters and retractors) operate properly and smoothly, and are installed securely. Check the belt web- bing for cuts, fraying, wear or damage. Steering wheel Check for changes in the steer- ing system, such as excessive freeplay, hard steering or strange noises. Warning lights and chimes Make sure all warning lights and chimes are operating properly. Windshield wiper and washer* Check that the wipers and washer operate properly and that the wipers do not streak.

Maintenance and do-it-yourself 8-3

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

where mud and dirt may have accumulated. See the (cid:147)Appearance and care(cid:148) section of this manual. Windshield washer fluid* Check that there is adequate fluid in the reservoir.

in each cell.

Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner. Under the hood and vehicle The maintenance items listed here should be checked periodically (for example, each time you check the engine oil or refuel). Battery* Check the fluid level It should be between the MAX and MIN lines. Ve- hicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. Brake fluid levels* Make sure that the brake fluid level is between the MIN and MAX lines on the reservoir. Engine coolant level* Check the coolant level when the engine is cold. Engine drive belts* Make sure the drive belts are not frayed, worn, cracked or oily. Engine oil level* Check the level after parking the vehicle on a level surface with the engine off. Wait more than 10 minutes for the oil to drain back into the oil pan. Exhaust system Make sure there are no loose supports, cracks or holes. If the sound of the exhaust seems unusual or there is a smell of 8-4 Maintenance and do-it-yourself

immediately have the exhaust exhaust fumes, system inspected by a NISSAN dealer. See the carbon monoxide warning in the (cid:147)Starting and driving(cid:148) section of this manual. Fluid leaks Check under the vehicle for fuel, oil, water or other fluid leaks after the vehicle has been parked for a while. Water dripping from the air conditioner after use is normal. If you should notice any leaks or if gasoline fumes are evident, check for the cause and have it corrected imme- diately. Power steering fluid level* and lines Check the level when the fluid is cold, with the engine off. Check the lines for proper attachment, leaks, cracks, etc. Radiator and hoses Check the front of the radiator and clean off any dirt, insects, leaves, etc., that may have accumulated. Make sure the hoses have no cracks, deformation, rot or loose connections. Underbody The underbody is frequently ex- posed to corrosive substances such as those used on icy roads or to control dust. It is very important to remove these substances from the underbody, otherwise rust may form on the floor pan, frame, fuel lines and exhaust system. At the end of winter, the underbody should be thor- oughly flushed with plain water, in those areas

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

MAINTENANCE PRECAUTIONS

When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precau- tions which should be closely observed.

WARNING

c Park the vehicle on a level surface, ap- ply the parking brake securely and block the wheels to prevent the vehicle from moving. Move the shift selector lever to P (Park).

c Be sure the ignition key is in the OFF or LOCK position when performing any parts replacement or repairs.

c Never leave the engine or automatic transmission related component har- nesses disconnected while the ignition switch is in the ON position.

c Never connect or disconnect the battery or any transistorized component while the ignition switch is in the ON position. c Your vehicle is equipped with an auto- matic engine cooling fan. It may come on at any time without warning, even if the ignition key is in the OFF position and the engine is not running. To avoid injury, always disconnect the negative battery cable before working near the fan.

c If you must work with the engine run- ning, keep your hands, clothing, hair and tools away from moving fans, belts and any other moving parts.

c It is advisable to secure or remove any loose clothing and remove any jewelry, such as rings, watches, etc. before working on your vehicle.

c Always wear eye protection whenever

you work on your vehicle.

c If you must run the engine in an en- closed space such as a garage, be sure there is proper ventilation for exhaust gases to escape.

c Never get under the vehicle while it is supported only by a jack. If it is neces- sary to work under the vehicle, support it with safety stands.

c Keep smoking materials,

flame and sparks away from the fuel tank and battery.

c On gasoline engine models with the multiport fuel injection (MFI) system, the fuel filter or fuel lines should be serviced by a NISSAN dealer because the fuel lines are under high pressure even when the engine is off.

CAUTION

c Do not work under the hood while the engine is hot. Turn the engine off and wait until it cools down.

c Avoid contact with used engine oil and coolant. Improperly disposed engine oil, engine coolant and/or other vehicle fluids can damage the environment. Al- ways conform to local regulations for disposal of vehicle fluid.

This (cid:147)Maintenance and do-it-yourself(cid:148) section gives instructions regarding only those items which are relatively easy for an owner to perform. A genuine NISSAN service manual is also avail- able. See (cid:147)Owner(cid:146)s Manual/Service Manual or- der information(cid:148) in the (cid:147)Technical and consumer information(cid:148) section of this manual. You should be aware that incomplete or improper servicing may result in operating difficulties or excessive emissions, and could affect warranty coverage. If in doubt about any servicing, have it done by a NISSAN dealer.

Maintenance and do-it-yourself 8-5

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

ENGINE COMPARTMENT CHECK LOCATIONS

Power steering fluid reservoir Engine oil filler cap Air cleaner Brake fluid reservoir Battery Fuse/fusible link box Transmission dipstick Engine oil dipstick Radiator cap

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Drive belt location 11. Fuse block 12. Windshield washer fluid reservoir 13. Engine coolant reservoir NOTE: Engine cover removed for clarity.

8-6 Maintenance and do-it-yourself

WDI0515

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

ENGINE COOLING SYSTEM

NISSAN

Genuine

The engine cooling system is filled at the factory with Life Antifreeze/Coolant to provide year-round anti- freeze and coolant protection. The anti-freeze solution contains rust and corrosion inhibitors. Additional engine cooling system additives are not necessary.

Long

WARNING

c Never remove the radiator or coolant reservoir cap when the engine is hot. Wait until the engine and radiator cool down. Serious burns could be caused by high pressure fluid escaping from the radiator. See precautions in (cid:147)If your vehicle overheats(cid:148) found in the (cid:147)In case of emergency(cid:148) section of this manual. c The radiator is equipped with a pres- sure type radiator cap. To prevent en- gine damage, use only a genuine NISSAN radiator cap.

Outside temperature

down to

(cid:176)C

-35

(cid:176)F

-30

Demineral- ized or dis- tilled water

Genuine NISSAN Long Life Antifreeze/ Coolant or equivalent

50%

50%

CAUTION

When adding or replacing coolant, be sure to use only a Genuine NISSAN Long Life Antifreeze/Coolant (green) or equivalent with the proper mixture ratio of 50% anti- freeze and 50% demineralized or distilled water. The use of other types of coolant solutions or coolant colors, such as or- ange, may damage the engine cooling system.

LDI0350

CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir when the engine is cold. If the coolant level is below the MIN level, add coolant to the MAX level. If the reservoir is empty, check the coolant level in the radiator when the engine is cold. If there is insufficient coolant in the radiator, fill the radiator with coolant up to the filler opening and also add it to the reservoir up to the MAX level. If the cooling system frequently requires coolant, have it checked by a NISSAN dealer.

Maintenance and do-it-yourself 8-7

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

ENGINE OIL

CHANGING ENGINE COOLANT A NISSAN dealer can change the engine coolant. The service procedure can be found in the NISSAN Service Manual. Improper servicing can result in reduced heater performance and engine overheat- ing.

WARNING

c To avoid the danger of being scalded, never change the coolant when the en- gine is hot.

c Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator.

c Avoid direct skin contact with used coolant. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.

c Keep coolant out of the reach of chil-

dren and pets.

LDI0351

CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and apply

the parking brake.

2. Start the engine and let it idle until it reaches

operating temperature.

3. Turn off the engine. Wait more than 10
minutes for the oil to drain back into the oil pan.

Engine coolant must be disposed of properly. Check your local regulations.

4. Remove the dipstick and wipe it clean. Re-

insert it all the way.

8-8 Maintenance and do-it-yourself

WDI0175
5. Remove the dipstick again and check the oil level. It should be between the H (High) and L (Low) marks sB . This is the normal oper- ating oil level range. If the oil level is below the L (Low) mark sA , remove the oil filler cap and pour recommended oil through the opening. Do not overfill sC .

6. Recheck oil level with the dipstick. It is normal to add some oil between oil maintenance intervals or during the break-in period, depending on the severity of operating conditions.

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

CAUTION

Oil level should be checked regularly. Op- erating the engine with an insufficient amount of oil can damage the engine, and such damage is not covered by warranty.

If the oil filter is to be changed, remove and replace it at this time. See (cid:147)Changing engine oil filter(cid:148) later in this section.

WARNING

c Prolonged and repeated contact with used engine oil may cause skin cancer. c Try to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.

c Keep used engine oil out of reach of

children.

CAUTION

Be careful not to burn yourself. The engine oil may be hot.

c Waste oil must be disposed of prop-

erly.

c Check your local regulations.

6. Clean and reinstall the drain plug and a new washer. Securely tighten the drain plug with a wrench. Do not use excessive force. Drain plug tightening torque: 22 - 29 ft-lb (29 - 39 N•m)

Maintenance and do-it-yourself 8-9

WDI0493

CHANGING ENGINE OIL 1. Park the vehicle on a level surface and apply

the parking brake.

2. Start the engine and let it idle until it reaches

operating temperature, then turn it off.

3. Remove the oil filler cap sA by turning it

counterclockwise.

4. Place a large drain pan under the drain plug

sB .

5. Remove the drain plug sB with a wrench by turning it counterclockwise and completely drain the oil.

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

and

(cid:147)Capacities

7. Refill engine with recommended oil through the oil filler opening, then install the oil filler cap securely. See recommended fuel/lubricants(cid:148) in the (cid:147)Technical and con- sumer information(cid:148) section of this manual for drain and refill capacity. The drain and refill capacity depends on the oil temperature and drain time. Use these specifications for reference only. Always use the dipstick to determine when the proper amount of oil is in the engine.

5. Wipe the engine oil filter sealing surface with

a clean rag. Be sure to remove any old gasket material remaining on the sealing surface of the en- gine.

6. Coat the gasket on the new filter with clean

engine oil.

7. Screw on the oil filter until a slight resistance

is felt, then tighten an additional 2/3 turn.

8. Start

the engine and check for leakage

around the oil filter. Correct as required.

9. Turn the engine off and wait more than 10
minutes. Check the oil level. Add engine oil if necessary.

8. Start the engine. Check for leakage around the drain plug and oil filter. Correct as re- quired.

9. Turn the engine off and wait more than 10
minutes. Check the oil level with the dipstick. Add engine oil if necessary.

8-10 Maintenance and do-it-yourself

WDI0495

CHANGING ENGINE OIL FILTER 1. Park the vehicle on a level surface and apply

the parking brake.

2. Turn the engine off. 3. Place a large drain pan under the oil filter sA . 4. Loosen the oil filter wrench by turning it counterclockwise. Then remove the oil filter by turning it by hand.

filter sA with an oil

CAUTION

Be careful not to burn yourself. The engine oil may be hot.

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

CAUTION

c DO NOT OVERFILL. c Recommended

is NISSAN PSF or equivalent.

fluid

Genuine

5-SPEED AUTOMATIC TRANSMISSION FLUID

POWER STEERING FLUID

When checking or replacement is required, we recommend your NISSAN dealer for servicing.

WARNING

c Use only Genuine NISSAN Matic K ATF.

Do not mix with other fluids.

c Using automatic transmission fluid other than Genuine NISSAN Matic K ATF will cause deterioration in drive- ability and automatic transmission du- rability, and may damage the automatic transmission, which is not covered by the NISSAN new vehicle limited warranty.

The specified automatic transmission fluid is also described on caution labels located in the engine compartment.

WDI0256
The fluid level should be checked using the HOT MAX range on the power steering fluid reservoir at fluid temperatures of 122(cid:176) - 176(cid:176)F (50(cid:176) - 80(cid:176)C) or using the COLD MAX range on the power steering fluid reservoir at fluid tempera- tures of 32(cid:176) - 86(cid:176)F (0(cid:176) - 30(cid:176)C). If the fluid is below the MIN line, add Genuine NISSAN PSF. Remove the cap and fill through the opening.

Maintenance and do-it-yourself 8-11

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

BRAKE FLUID

WINDOW WASHER FLUID

to

For further brake fluid specification information, refer recommended fuel/lubricants(cid:148) in the (cid:147)Technical and consumer information(cid:148) section of this manual.

(cid:147)Capacities

and

WARNING

Use only new fluid from a sealed con- tainer. Old, inferior or contaminated fluid may damage the brake system. The use of improper fluids can damage the brake system and affect the vehicle(cid:146)s stopping ability.

CAUTION

Do not spill the fluid on any painted sur- faces. This will damage the paint. If fluid is spilled, immediately wash the surface with water.

8-12 Maintenance and do-it-yourself

WDI0512

LDI0355

BRAKE FLUID Check the brake fluid level in the reservoir. If the fluid level is below the MIN line or the brake warning light comes on, add Genuine NISSAN Super Heavy Duty Brake Fluid or equivalent DOT 3 fluid up to the MAX line. If fluid must be added frequently, the system should be checked by a NISSAN dealer.

WINDOW WASHER FLUID RESERVOIR Fill the window washer fluid reservoir periodically. Add window washer fluid when the low window washer fluid warning light comes on.

To fill the window washer fluid reservoir, lift the cap off the reservoir tank and pour the window washer fluid into the tank opening.

Add a washer solvent to the washer for better cleaning. In the winter season, add a windshield washer antifreeze. Follow the manufacturer(cid:146)s in- structions for the mixture ratio.

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

c When working on or near a battery, al- ways wear suitable eye protection and remove all jewelry.

c Battery posts, terminals and related ac- cessories contain lead and lead com- pounds. Wash hands after handling.

c Keep battery out of

children.

the reach of

Refill the reservoir more frequently when driving conditions require an increased amount of win- dow washer fluid. Recommended fluid is Genuine NISSAN Wind- shield Washer Concentrate Cleaner & Anti- freeze or equivalent.

CAUTION

c Do not substitute engine anti-freeze coolant for window washer solution. This may result in damage to the paint. c Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reser- voir tank.

c Pre-mix washer fluid concentrates with water to the manufacturer(cid:146)s recom- mended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concen- trate and water.

BATTERY

c Keep the battery surface clean and dry. Any corrosion should be washed off with a solu- tion of baking soda and water.

c Make certain the terminal connections are

clean and securely tightened.

c If the vehicle is not to be used for 30 days or longer, disconnect the negative (-) battery terminal cable to prevent discharge.

WARNING

c Do not expose the battery to flames or electrical sparks. Hydrogen gas gener- ated by the battery is explosive. Do not allow battery fluid to contact your skin, eyes, fabrics or painted surfaces. After touching a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 minutes and seek medical attention.

c Do not operate the vehicle if the fluid in the battery is low. Low battery fluid can cause a higher load on the battery which can generate heat, reduce bat- tery life, and in some cases lead to an explosion.

Maintenance and do-it-yourself 8-13

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. JUMP STARTING If jump starting is necessary, see (cid:147)Jump starting(cid:148) in the (cid:147)In case of emergency(cid:148) section of this manual. If the engine does not start by jump starting, the battery may have to be replaced. Contact a NISSAN dealer.

WDI0224
1. Remove the battery caps with a screwdriver as shown. Use a cloth to protect the battery case.

8-14 Maintenance and do-it-yourself

2. Check the fluid level

LDI0302
If it is necessary to add fluid, add only distilled water to bring the level up to the bottom of the filler opening. Do not overfill.

in each cell

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

DRIVE BELTS

SPARK PLUGS

2. Have the belts checked regularly for condi- tion and tension in accordance with the maintenance the (cid:147)NISSAN Service and Maintenance Guide(cid:148).

schedule

found

in

WDI0226

Power steering fluid pump

1. 2. Crankshaft 3. Generator 4.

Air conditioner

WARNING

Be sure the ignition key is in the OFF or LOCK position. The engine could rotate unexpectedly.

1. Visually inspect the belt(s) for signs of un- usual wear, cuts, fraying or looseness. If the belt is in poor condition or is loose, have it replaced or adjusted by a NISSAN dealer.

WDI0005

REPLACING SPARK PLUGS Platinum-tipped spark plugs It is not necessary to replace platinum-tipped spark plugs as frequently as conventional type spark plugs because they last much longer. Fol- low the maintenance log shown in the (cid:147)NISSAN Service and Maintenance Guide(cid:148). Do not service platinum-tipped spark plugs by cleaning or re- gapping. c Always replace spark plugs with rec-

ommended or equivalent ones.

Maintenance and do-it-yourself 8-15

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

AIR CLEANER

WARNING

Be sure the engine and ignition switch are off and that the parking brake is engaged securely.

CAUTION

Be sure to use the correct socket to re- move the spark plugs. An incorrect socket can damage the spark plugs.

If replacement is required, see your NISSAN dealer for assistance.

LDI0357
The air cleaner filter should not be cleaned and reused. Replace it according to the maintenance log shown in the (cid:147)NISSAN Service and Mainte- nance Guide.(cid:148) When replacing the filter, wipe the inside of the air cleaner filter housing and the cover with a damp cloth.

Loosen the screw.

To remove the air cleaner filter: s1
s2 Disconnect the electrical connector. s3 Unlatch the clips and remove the air cleaner

cover. Remove the air cleaner filter.

8-16 Maintenance and do-it-yourself

WARNING

c Operating the engine with the air cleaner removed can cause you or oth- ers to be burned. The air cleaner not only cleans the air, it stops the flame if the engine backfires. If it isn(cid:146)t there, and the engine backfires, you could be burned. Do not drive with the air cleaner removed, and be careful when working on the engine with the air cleaner removed.

c Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed. Doing so could result in serious injury.

IN-CABIN MICROFILTER The in-cabin microfilter restricts the entry of air- borne dust and pollen particles and reduces some objectionable outside odors. The filter is located behind the glove box. Refer to the (cid:147)NISSAN Service and Maintenance Guide(cid:148) for change intervals. If replacement is required, see your NISSAN dealer.

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

WINDSHIELD WIPER BLADES

CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water. Clean each blade by wiping it with a cloth soaked in a washer solution or a mild detergent. Then rinse the blades with clear water. If your wind- shield is still not clear after cleaning the blades and using the wiper, replace the blades.

CAUTION

Worn windshield wiper blades can dam- age the windshield and impair driver vision.

REPLACING Replace the wiper blades if they are worn. s1
Lift the wiper arm away from the windshield. s2 Push the release tab, then move the wiper

blade down the wiper arm to remove.

s3 Remove the wiper blade.

4.

WDI0194
Insert the new wiper blade onto the wiper arm until it clicks into place.

CAUTION

c After wiper blade replacement, return the wiper arm to its original position; otherwise it may be damaged when the hood is opened.

c Make sure the wiper blades contact the glass; otherwise the arms may be dam- aged from wind pressure.

Maintenance and do-it-yourself 8-17

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

WDI0337
Be careful not to let anything get into the washer nozzle sA . This may cause clogging or improper windshield washer operation. If something gets into the nozzle, remove it with a needle or small pin sB .

8-18 Maintenance and do-it-yourself

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

Rear window wiper blade s1

Lift the wiper arm away from the rear win- dow.

LDI0356

s2 Push the wiper blade in and pivot until the

s3

blade becomes free. Insert a new blade onto the wiper arm and snap into place.

Maintenance and do-it-yourself 8-19

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

BRAKE PEDAL

FUSES

Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes. The front and rear disc-type brakes self-adjust every time the brake pedal is applied.

WARNING

See a NISSAN dealer for a brake system check if the brake pedal height does not return to normal. Brake pad wear indicators The disc brake pads on your vehicle have audible wear indicators. When a brake pad requires re- placement, a high pitched scraping or screech- ing sound will be heard when the vehicle is in motion. The noise will be heard whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the wear indicator sound is heard. Under some driving or climate conditions, occa- sional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is normal and does not affect the function or performance of the brake system.

8-20 Maintenance and do-it-yourself

Proper brake inspection intervals should be followed. For more information regarding brake inspections, see the appropriate mainte- nance schedule information in the (cid:147)NISSAN Ser- vice and Maintenance Guide(cid:148).

LDI0358

ENGINE COMPARTMENT

CAUTION

Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.

If any electrical equipment does not come on, check for an open fuse.

1. Be sure the ignition switch and the headlight

switch are OFF.

2. Open the engine hood.

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

3. Remove the fuse box cover by pushing the

tab and lifting the cover up.

4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment.

5.

6.

WDI0452
If the fuse is open sA , replace it with a new fuse sB . If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.

Fusible links If the electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace with only genuine NISSAN parts.

LDI0516

PASSENGER COMPARTMENT

CAUTION

Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.

If any electrical equipment does not operate, check for an open fuse.

1. Be sure the ignition switch and the headlight

switch are OFF.

Maintenance and do-it-yourself 8-21

Z REVIEW COPY—2007 Quest (van) Owners Manual—USA_English (nna) 02/27/06—debbie X

2. Pull the sunglasses holder down to open s1 . 3. Pull up on the sunglasses holder s2 and

remove to expose the fuse panel.

4. Remove the fuse with the fuse puller.

WDI0452

LDI0456

5.

Type A

If the fuse is open sA , replace it with a known good fuse sB .

6. Push the fuse box cover to install. 7.

If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.