authorized repair shop. The engine oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. See (cid:147)Engine oil(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) section of this manual.
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
CAUTION
Running the engine with the engine oil pressure warning light on could cause se- rious damage to the engine almost imme- diately. Such damage is not covered by warranty. Turn off the engine as soon as it is safe to do so.
Low fuel warning light
This light comes on when the fuel level in the fuel tank is getting low. The low fuel warning chime will also sound under certain conditions. See (cid:147)Low fuel warning chime(cid:148) later in this section.
Refuel as soon as it is convenient, preferably before the fuel gauge reaches E (Empty). There will be a small reserve of fuel in the tank when the fuel gauge needle reaches E (Empty).
Low tire pressure warning light
After the ignition switch is turned ON, this light comes on for about 1 second and turns off. This light warns of low tire pressure. NISSAN(cid:146)s low tire pressure warning system is a tire pressure monitoring system. It monitors tire pressure of all tires except the spare. When the
tire pressure monitoring system warning light is lit, one or more of your tires is significantly under- inflated. You should stop and check your tires as soon as possible, and inflate them to the proper pressure as indicated on the vehicle(cid:146)s tire infor- mation placard. Driving on a significantly under- inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle(cid:146)s handling and stopping ability. Each tire, including the spare, should be checked monthly when cold and set to the recommended inflation pressure as specified in the vehicle plac- ard and owner(cid:146)s manual.
The recommended inflation pressure may also be found on the Tire and Loading Information Label. Low tire pressure warning:
If the vehicle is being driven with very low tire pressure (lower than 28 psi, 193 kPa), the light will illuminate and the chime will sound for about 10 seconds. If you select the tire pressure infor- mation in the display, the FLAT TIRE warning message will be displayed.
For additional information, see (cid:147)Low tire pressure warning system(cid:148) in the (cid:147)Starting and driving(cid:148) section and (cid:147)Low tire pressure warning system(cid:148) in the (cid:147)In case of emergency(cid:148) section.
WARNING
c If the light does not come on with the key switch turned ON, have the vehicle checked by a NISSAN dealer as soon as possible.
c If the light comes on while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If the light still comes on while driving after adjusting the tire pressure, a tire may be flat. If you have a flat tire, re- place it with a spare tire as soon as possible.
Instruments and controls 2-9
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
c When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated and the low tire pressure warning system will not function. Con- tact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.
CAUTION
c The low tire pressure warning system is not a substitute for the regular tire pres- sure check. Be sure to check the tire pressure regularly.
c If the vehicle is being driven at speeds of less than 20 MPH (32 km/h), the low tire pressure warning system may not operate correctly.
c Be sure to install the specified size of
tires to the 4 wheels correctly.
Low windshield washer fluid warning light
This light comes on when the windshield washer fluid is at a low level. Add windshield washer fluid as necessary. See (cid:147)Window washer fluid(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) section of this manual.
2-10 Instruments and controls
Seat belt warning light and chime
The light and chime remind you to fasten your seat belts. The light illuminates whenever the ignition key is turned to the ON or START position and remains illuminated until the driver(cid:146)s seat belt is fastened. At the same time, the chime sounds for about 6 seconds unless the driver(cid:146)s seat belt is securely fastened.
Refer to (cid:147)Seat belts(cid:148) in the (cid:147)Safety(cid:151)Seats, seat belts and supplemental restraint system(cid:148) section for precautions on seat belt usage.
Supplemental air bag warning light
When the ignition key is in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational.
the following conditions occur,
If any of the supplemental front air bag, supplemental side air bag (if so equipped), curtain side-impact air bags, and pre-tensioner seat belt systems need servicing and your vehicle must be taken to a NISSAN dealer: c The supplemental air bag warning light re-
mains on after approximately 7 seconds.
c The supplemental air bag warning light
flashes intermittently.
c The supplemental air bag warning light does
not come on at all.
Unless checked and repaired, the supplemental restraint system (air bag system) and/or the pre- tensioner seat belts may not function properly. For additional details see (cid:147)Supplemental restraint sys- tem(cid:148) in the (cid:147)Safety(cid:151)Seats, seat belts and supple- mental restraint system(cid:148) section of this manual.
WARNING
If the supplemental air bag warning light is on, it could mean that the supplemental front air bag, supplemental side air bag (if so equipped), curtain side-impact air bag systems and/or pre-tensioner seat belt systems will not operate in an accident. To help avoid injury to yourself or others, have your vehicle checked by a NISSAN dealer as soon as possible. INDICATOR LIGHTS
Automatic transmission posi- tion indicator light
When the ignition key is turned to the ON posi- tion, the indicator in the tachometer shows the automatic transmission selector lever position.
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
See (cid:147)Driving the vehicle(cid:148) in the (cid:147)Starting and driving(cid:148) section of this manual.
Cruise main switch indicator light
The light comes on when the cruise control main switch is pushed. The light goes out when the main switch is pushed again. When the cruise main switch indicator light comes on, the cruise control system is operational.
Cruise set switch indicator light
The light comes on while the vehicle speed is controlled by the cruise control system. If the light blinks while the engine is running, it may indicate the cruise control system is not functioning prop- erly. Have the system checked by a NISSAN dealer.
High beam indicator light (Blue)
This blue light comes on when the headlight high beams are on and goes out when the low beams are selected.
The high beam indicator light also comes on when the passing signal is activated.
Malfunction indicator lamp (MIL)
If this indicator lamp comes on steady or blinks while the engine is running, it may indicate a potential emission control malfunction.
The malfunction indicator lamp may also come on
steady if the fuel filler cap is loose or missing, or if
the vehicle runs out of fuel. Check to make sure
the fuel filler cap is installed and closed tightly,
and that the vehicle has at least 3 gallons (11.4
liters) of fuel in the fuel tank.
After a few driving trips, the
lamp should
turn off if no other potential emission control
system malfunction exists.
If this indicator lamp comes on steady for 20
seconds and then blinks for 10 seconds when
the engine is not running, it indicates that the
vehicle is not ready for an emission control sys-
tem inspection/maintenance test. See (cid:147)Readi-
ness for inspection/maintenance (I/M) test(cid:148) in the
(cid:147)Technical and consumer information(cid:148) section of
this manual.
Operation
The malfunction indicator lamp will come on in
one of two ways:
c Malfunction indicator lamp on steady (cid:151) An
emission control system malfunction has
been detected. Check the fuel filler cap. If the fuel filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The lamp should turn off after a few driving trips. If the lamp does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.
c Malfunction indicator lamp blinking (cid:151) An engine misfire has been detected which may damage the emission control system. To re- duce or avoid emission control system dam- age:
(cid:150) do not drive at speeds above 45 MPH
(72 km/h).
(cid:150) avoid hard acceleration or deceleration.
(cid:150) avoid steep uphill grades.
(cid:150) if possible, reduce the amount of cargo
being hauled or towed.
The malfunction indicator lamp may stop blinking and come on steady. Have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.
Instruments and controls 2-11
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
CAUTION
Security indicator light
Continued vehicle operation without hav- ing the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission con- trol system.
Overdrive off indicator light
This light comes on when the overdrive function is OFF.
The automatic transmission overdrive function is controlled by the overdrive switch.
See (cid:147)Driving the vehicle(cid:148) in the (cid:147)Starting and driving(cid:148) section of this manual.
or
Front passenger air bag status light
The front passenger air bag status light ( or ) will be lit and the passenger front air bag will be OFF depending on how the front passenger seat is being used.
For front passenger air bag status light operation, see (cid:147)Front passenger air bag and status light(cid:148) in the (cid:147)Safety (cid:151) Seats, seat belts and supplemental restraint system(cid:148) section of this manual.
2-12 Instruments and controls
This light blinks whenever the ignition switch is in the LOCK, OFF or ACC position. This function indicates the security system equipped on the vehicle is operational.
For additional tems(cid:148) later in this section.
information, see (cid:147)Security sys-
Slip indicator light
This indicator light will blink when the traction control system is limiting wheel spin. Slippery road conditions may exist if the slip indicator blinks on. If this happens, adjust your driving accordingly.
The slip indicator light also comes on when you turn the ignition key to the ON position. The light will turn off after about 2 seconds if the system is operational. If the light does not come on or go off, have the traction control system checked by a NISSAN dealer.
Traction control system off indicator light (if so equipped) This indicator light comes on when the traction control off switch is pushed to OFF. This indi- cates the traction control system is not operating.
Push the traction control off switch again or re- start the engine and the system will operate nor- mally. See (cid:147)Traction control system (TCS)(cid:148) in the (cid:147)Starting and driving(cid:148) section of this manual.
The traction control light also comes on when you turn the ignition key to the ON position. The light will turn off after about 2 seconds if the traction control system (TCS) is operational. If the light stays on or comes on along with the SLIP indica- tor light while you are driving, have the traction control system checked by a NISSAN dealer.
While the traction control system is operating, you might feel slight vibration or hear the system working when starting the vehicle or accelerat- ing, but this is normal.
Turn signal/hazard indicator lights
The appropriate light flashes when the turn signal switch is activated.
Both lights flash when the hazard switch is turned on.
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
Vehicle dynamic control off indicator light (if so equipped) This indicator light comes on when the vehicle dynamic control off switch is pushed to OFF. This indicates the vehicle dynamic control system is not operating. Push the vehicle dynamic control off switch again or restart the engine and the system will operate normally. See (cid:147)Vehicle dynamic control (VDC) system(cid:148) in the (cid:147)Starting and driving(cid:148) section of this manual. The vehicle dynamic control light also comes on when you turn the ignition key to the ON position. The light will turn off after about 2 seconds if the system is operational. If the light stays on or comes on along with the SLIP indicator light while you are driving, have the vehicle dynamic control system checked by a NISSAN dealer. While the vehicle dynamic control system is op- erating, you might feel slight vibration or hear the system working when starting the vehicle or ac- celerating, but this is normal.
AUDIBLE REMINDERS Brake pad wear warning The front disc brake pads have audible wear warnings. When a front brake pad requires re- placement, it makes a high pitched scraping sound when the vehicle is in motion, whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the warn- ing sound is heard. Key reminder chime A chime sounds if the driver(cid:146)s door is opened while the key is left in the ignition switch. Remove the key and take it with you when leaving the vehicle. Light reminder chime With the ignition switch in the OFF position, a chime sounds when the driver(cid:146)s door is opened if the headlights or parking lights are on. Turn the headlight control switch off before leav- ing the vehicle. Low fuel warning chime A chime sounds briefly when the low fuel warning light initially comes on. If the low fuel warning light turns off during the driving trip and then turns on again, the chime will not sound.
SECURITY SYSTEMS
WIC0834
Your vehicle has two types of security systems:
c Vehicle security system
c NISSAN Vehicle Immobilizer System(cid:151)NVIS
VEHICLE SECURITY SYSTEM
The vehicle security system provides visual and
audible alarm signals if someone opens the doors
when the system is armed. It is not, however, a
motion detection type system that activates when
a vehicle is moved or when a vibration occurs.
The system helps deter vehicle theft but cannot
prevent it, nor can it prevent the theft of interior or
exterior vehicle components in all situations. Al-
ways secure your vehicle even if parking for a
Instruments and controls 2-13
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
brief period. Never leave your keys in the ignition, and always lock the vehicle when unattended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible.
Many devices offering additional protection, such as component locks, identification markers, and tracking systems, are available at auto supply stores and specialty shops. Your NISSAN dealer may also offer such equipment. Check with your insurance company to see if you may be eligible for discounts for various theft protection features. How to arm the vehicle security sys- tem 1. Close all windows. (The system can be armed even if the windows are open.)
2. Remove the key from the ignition switch. 3. Close all doors. Lock all doors. The doors can be locked with the key, power door lock switch or with the keyfob. Keyfob operation: c Push the
button on the keyfob. All doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked.
c When the
button is pushed with all doors locked, the hazard lights flash
2-14 Instruments and controls
twice and the horn beeps once as a re- minder that the doors are already locked.
The horn may or may not beep. Refer to (cid:147)Personalized settings menu(cid:148) (vehicles with- out navigation system) or (cid:147)Vehicle electronic systems(cid:148) (vehicles with navigation system) in the (cid:147)Display screen, heater, air conditioner and audio systems(cid:148) section later in this manual.
4. Confirm that the
indicator light comes
on. The
light stays on for about 30
seconds. The vehicle security system is now
pre-armed. After about 30 seconds the ve-
hicle security system automatically shifts
into the armed phase. The
light begins
to flash once every 3 seconds. If, during the
30-second pre-arm time period, the door is
unlocked by the key or the keyfob, or the
ignition key is turned to ACC or ON, the
system will not arm.
c If the key is turned slowly when locking the door, the system may not arm. Fur- thermore, if the key is turned beyond the vertical position toward the unlock position to remove the key, the system may be disarmed when the key is re- moved. If the indicator light fails to glow for 30 seconds, unlock the door once and lock it again.
c Even when the driver and/or passen- gers are in the vehicle, the system will arm with all doors closed and locked with the ignition key in the OFF posi- tion.
Vehicle security system activation The vehicle security system will give the following alarm: c The headlights blink and the horn sounds
intermittently.
c The alarm automatically turns off after ap- proximately 50 seconds. However, the alarm reactivates if the vehicle is tampered with again. The alarm can be shut off by unlocking a door with the key, or by pressing the button on the keyfob. The alarm is activated by: c opening a door without using the key or keyfob (even if the door is unlocked by using the inside lock knob or the power door lock switch).
How to stop an activated alarm The alarm stops only by unlocking a door with the key, or by pressing the button on the key- fob.
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
Statement related to Section 15 of FCC Rules for NISSAN Vehicle Immobilizer Sys- tem (CONT ASSY (cid:151) IMMOBILIZER, ANT ASSY (cid:151) IMMOBILIZER) This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the follow- ing two conditions; (1) This device may not cause harmful in- terference, and (2) this device must accept any interference received, including inter- ference that may cause undesired opera- tion of the device. CHANGES OR MODIFICATIONS NOT EX- PRESSLY APPROVED BY THE MANUFAC- TURER FOR COMPLIANCE COULD VOID THE USER(cid:146)S AUTHORITY TO OPERATE THE EQUIPMENT.
NISSAN VEHICLE IMMOBILIZER SYSTEM (NVIS) The NISSAN Vehicle Immobilizer System (NVIS) will not allow the engine to start without the use of a registered NVIS key. If the engine fails to start using a registered NVIS key (for example, when interference is caused by another NVIS key, an automated toll road device or automatic payment device on the key ring), restart the engine using the following proce- dures: 1. Leave the ignition switch in the ON position
for approximately 5 seconds.
2. Turn the ignition switch to the OFF or LOCK position, and wait approximately 10 sec- onds.
3. Repeat steps 1 and 2. 4. Restart the engine while holding the device (which may have caused the interference) separate from the registered NVIS key.
If the no start condition re-occurs, NISSAN rec- ommends placing the registered NVIS key on a separate key ring to avoid interference from other devices.
LIC0474
Security indicator light The security indicator light blinks whenever the ignition switch is in the LOCK, OFF or ACC position. This function indicates the NISSAN Ve- hicle Immobilizer System (NVIS) is operational. If the NVIS is malfunctioning, the light will remain on while the ignition key is in the ON position. If the light still remains on and/or the en- gine will not start, see a NISSAN dealer for NVIS service as soon as possible. Please bring all NVIS keys that you have when visiting your NISSAN dealer for service.
Instruments and controls 2-15
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
WINDSHIELD WIPER AND WASHER SWITCH
WIC0843
SWITCH OPERATION The windshield wiper and washer operates when the ignition switch is in the ON position.
Push the lever down to operate the wiper at the
following speed:
s1
Intermittent (cid:151) intermittent operation can be adjusted by turning the knob toward sA (Slower) or sB (Faster). Also, the intermit- tent operation speed varies in accordance with the vehicle speed. (For example, when the vehicle speed is high, the intermittent operation speed will be faster.)
2-16 Instruments and controls
NOTE:
You can turn on or turn off the driving
speed dependent intermittent wiper func-
tion. Refer
to (cid:147)Personalized settings
menu(cid:148) (vehicles without navigation sys-
tem) or (cid:147)Vehicle electronic systems(cid:148) (ve-
hicles with navigation system) in the (cid:147)Dis-
play screen, heater, air conditioner and
audio systems(cid:148) section later in this manual.
s2
Low (cid:151) continuous low speed operation
s3 High (cid:151) continuous high speed operation
Push the lever up s4 to have one sweep opera-
tion of the wiper.
Pull the lever toward you s5
to operate the
washer. The wiper will also operate several times.
WARNING
In freezing temperatures the washer solu- tion may freeze on the windshield and obscure your vision which may lead to an accident. Warm the windshield with the defroster before you wash the windshield.
CAUTION
c Do not operate the washer continu-
ously for more than 30 seconds.
c Do not operate the washer if the reser-
voir tank is empty.
c Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reser- voir tank.
c Pre-mix washer fluid concentrates with water to the manufacturer(cid:146)s recom- mended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concen- trate and water.
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 08/09/04—tmchalpi X
REAR WINDOW WIPER AND WASHER SWITCH
REAR WINDOW AND OUTSIDE MIRROR (if so equipped) DEFROSTER SWITCH
WARNING
In freezing temperatures the washer solu- tion may freeze on the window and ob- scure your vision. Warm the rear window with the defroster before you wash the rear window.
CAUTION
c Do not operate the washer continu-
ously for more than 30 seconds.
c Do not operate the washer if the reser-
voir tank is empty.
c Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reser- voir tank.
c Pre-mix washer fluid concentrates with water to the manufacturer(cid:146)s recom- mended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concen- trate and water.
WIC0844
The rear window wiper and washer operate when
the ignition switch is in the ON position.
Turn the switch clockwise from the OFF position
to operate the wiper.
s1
Intermittent (cid:150) intermittent operation (not ad- justable)
Low (cid:150) continuous low speed operation
s2
Push the switch forward s3
to operate the
washer. The wiper will also operate several times.
Type A
LIC0782
To defrost the rear window glass and outside mirrors (if so equipped), start the engine and push the rear window defroster switch on. The rear window defroster indicator light comes on. Push the switch again to turn the defroster off. The rear window defroster automatically turns off after approximately 15 minutes.
CAUTION
When cleaning the inner side of the rear window, be careful not to scratch or dam- age the rear window defroster.
Instruments and controls 2-17
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 08/09/04—tmchalpi X
HEADLIGHT AND TURN SIGNAL SWITCH
LIC0488
LIC0560
LIC0687
Type B
Type A
HEADLIGHT CONTROL SWITCH Lighting s1 When turning the switch to the
posi- tion, the front parking, tail, license plate and instrument panel lights come on. s2 When turning the switch to the
posi- tion, the headlights come on and all the other lights remain on.
Type B
CAUTION
Use the headlights with the engine run- ning to avoid discharging the vehicle battery.
2-18 Instruments and controls
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
NOTE: Autolight activation sensitivity and the time delay for autolight shutoff can be ad- justed. See (cid:147)Personalized settings menu(cid:148) (vehicles without navigation system) or (cid:147)Vehicle electronic systems(cid:148) (vehicles with navigation system) in the (cid:147)Display screen, heater, air conditioner and audio systems(cid:148) section later in this manual. To turn on the autolight system: 1. Turn the headlight switch to the AUTO posi-
tion s1 .
2. Turn the ignition key to ON. 3. The autolight system automatically turns the
headlights on and off.
Initially, if the ignition switch is turned OFF and a door is opened and left open, the headlights remain on for 5 minutes. During that 5 minutes: c if all doors are closed, the headlights remain
on for 45 seconds, then turn off.
c if another door is opened, then the 5 minute
timer is reset.
To turn the autolight system off, turn the switch to the OFF,
position.
, or
Type C
LIC0688
LIC0561
Autolight system (if so equipped) The autolight system allows the headlights to be set so they turn on and off automatically. The autolight system can: c Turn on the headlights, front parking, tail, license plate and instrument panel lights au- tomatically when it is dark.
c Turn off all the lights when it is light. c Keep all the lights on for 45 seconds after you turn the key to OFF and all doors are closed.
Instruments and controls 2-19
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
After the headlights automatically turn off with the position, headlight switch in the the headlights will illuminate again for 5 minutes if the headlight switch is moved to the OFF position and then turned to the position.
or
or
LIC0515
Be sure you do not put anything on top of
the autolight sensor s1 located on top of
the instrument panel. The autolight sensor
controls the autolight; if it is covered, the
autolight sensor reacts as if it is dark out
and the headlights will illuminate. If this
occurs while parked with the engine off
and the key in the ON position, your vehi-
cle(cid:146)s battery could become discharged.
LIC0390
Headlight beam select s1 To select the high beam function, push the lever forward. The high beam lights come on and the
light illuminates.
s2 Pull the lever back to select the low beam. s3 Pulling and releasing the lever flashes the
headlight high beams on and off.
Battery saver system If the ignition switch is turned OFF while the headlight switch is in the posi- tion, the headlights will turn off after 5 minutes.
or
2-20 Instruments and controls
CAUTION
Even though the battery saver feature au- tomatically turns off the headlights after a period of time, you should turn the head- light switch to the OFF position when the engine is not running to avoid discharging the vehicle battery.
DAYTIME RUNNING LIGHT SYSTEM (Canada only) The headlights automatically illuminate at a re- duced intensity when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the position. Turn the OFF position or in the headlight switch to the position for full illumination when driving at night. If the parking brake is applied before the engine is started, the daytime running lights do not illumi- nate. The daytime running lights illuminate when the parking brake is released. The daytime run- ning lights will remain on until the ignition switch is turned off.
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
WARNING
When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.
LIC0392
LIC0563
INSTRUMENT BRIGHTNESS CONTROL The instrument cluster illuminates when the igni- tion switch is in ON position. The instrument brightness control operates when the the AUTO, Turn the control to adjust the brightness of instru- ment panel lights when driving at night. The instrument brightness control will not adjust the brightness when the headlights or parking lights are off.
headlight or
position.
control
switch
in
is
TURN SIGNAL SWITCH Turn signal s1 Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signals cancel automatically.
Lane change signal s2 To signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch.
Instruments and controls 2-21
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
HAZARD WARNING FLASHER SWITCH
LIC0393
FOG LIGHT SWITCH (if so equipped)
To turn the fog lights on, turn the headlight switch
to the
position, then turn the fog light
switch to the
position. To turn them off,
turn the fog light switch to the OFF position.
The headlights must be on and the low beams
selected for the fog lights to operate. The fog
lights automatically turn off when the high beam
headlights are selected.
2-22 Instruments and controls
AIC0102
LIC0394
CORNERING LIGHT The cornering light provides additional illumina- tion toward the turning direction. The cornering light will illuminate on the turning direction side when a turn is signaled with the headlights on.
Push the switch on to warn other drivers when you must stop or park under emergency condi- tions. All turn signal lights flash.
WARNING
c If stopping for an emergency, be sure to
move the vehicle well off the road.
c Do not use the hazard warning flashers while moving on the highway unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic.
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
HORN
HEATED SEAT (if so equipped)
c Turn signals do not work when the haz-
ard warning flasher lights are on.
The flashers will operate with the ignition switch in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving.
LIC0395
LIC0469
To sound the horn, push the center pad area of the steering wheel.
WARNING
Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tam- pering with the supplemental front air bag system may result in serious personal injury.
The front seats are warmed by built-in heaters (if so equipped). The switches are located at the sides of the seats.
1. Start the engine.
2. Push the
(low) or
(high) posi- tion of the switch, as desired, depending on the temperature. The indicator light in the switch will illuminate.
The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on.
Instruments and controls 2-23
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
3. When the seat is warmed or before you leave
the vehicle, be sure to turn the switch off.
CAUTION
c Do not use the seat heater for extended periods or when no one is using the seat. c Do not put anything on the seat which insulates heat, such as a blanket, cush- ion, seat cover, etc. Otherwise, the seat may become overheated.
c Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater.
c Any liquid spilled on the heated seat should be removed immediately with a dry cloth.
c When cleaning the seat, never use gasoline, benzine, thinner, or any simi- lar materials.
c If any abnormalities are found or the heated seat does not operate, turn the switch off and have the system checked by your NISSAN dealer.
c The battery could run down if the seat heater is operated while the engine is not running.
2-24 Instruments and controls
TRACTION CONTROL SYSTEM (TCS) OFF SWITCH (if so equipped)
VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH (if so equipped)
LIC0451
The vehicle should be driven with the Traction Con-
trol System (TCS) on for most driving conditions.
If the vehicle is stuck in mud or snow, the TCS reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine power is needed to free a stuck vehicle, turn the TCS off. To turn off the TCS, push the TCS OFF switch. The Push the (cid:147)TCS OFF(cid:148) switch again or restart the engine to turn ON the system. See (cid:147)Traction control system (TCS)(cid:148) in the (cid:147)Starting and driv- ing(cid:148) section.
indicator will come on.
WIC0534
The vehicle should be driven with the Vehicle
Dynamic Control (VDC) system on for most driv-
ing conditions.
If the vehicle is stuck in mud or snow, the VDC
system reduces the engine output to reduce
wheel spin. The engine speed will be reduced
even if the accelerator is depressed to the floor. If
maximum engine power is needed to free a stuck
vehicle, turn the VDC system off.
To turn off the VDC system, push the VDC OFF
switch. The
Push the VDC OFF switch again or restart the
engine to turn ON the system. See (cid:147)Vehicle dy-
namic control (VDC) system(cid:148) in the (cid:147)Starting and
driving(cid:148) section.
indicator will come on.
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
REAR SONAR SYSTEM OFF SWITCH (if so equipped)
POWER OUTLET
The rear sonar system can be disabled by push- ing the OFF switch. When the system is disabled, the indicator light on the switch will illuminate. The system will automatically reset the next time the ignition switch is turned on. See (cid:147)Rear sonar system(cid:148) in the (cid:147)Starting and driving(cid:148) section.
LIC0471
WARNING
The rear sonar system is a convenience but it is not a substitute for proper back- ing. Always turn and check that it is safe to do so before backing up. Always back up slowly.
The rear sonar system (if so equipped) is active when the ignition is in the ON position and the shift selector lever is in R (Reverse).
When sensors detect obstacles within 6 ft (1.8
m) of the rear bumper, a beeping tone is emitted.
WIC0838
Passenger compartment
The power outlets are for powering electrical accessories such as cellular telephones.
The power outlets located inside the center con- sole storage bin and in the cargo area are pow- ered directly by the vehicle(cid:146)s battery.
The power outlets located on the side of the center console and in the 2nd row are powered only when the ignition key is in the ACC or ON position.
Open the cap to use a power outlet.
Instruments and controls 2-25
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
Inside center console storage bin
2nd row
Cargo area
WIC0839
LIC0516
LIC0517
CAUTION
c The outlet and plug may be hot during
or immediately after use.
c This power outlet is not designed for
use with a cigarette lighter unit.
c Do not use with accessories that ex- ceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.
c Use power outlets with the engine run- ning to avoid discharging the vehicle battery.
2-26 Instruments and controls
c Avoid using power outlets when the air conditioner, headlights or rear window defroster is on.
c Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned OFF.
c Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal temperature fuse may open.
c When not in use, be sure to close the cap. Do not allow water to contact the outlet.
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
STORAGE
LIC0498
LIC0495
LIC0501
NOTE HOLDER Insert a card or photograph into the note holder.
WARNING
Do not use note holder while driving so full attention may be given to vehicle operation.
Driver(cid:146)s side
LOWER INSTRUMENT PANEL STORAGE TRAYS
WARNING
Do not place sharp objects in the trays to help prevent injury in an accident or sud- den stop.
UPPER INSTRUMENT PANEL STORAGE COMPARTMENT Push the button to release the lid to the 1st open position. You can raise and hold the lid by hand to the 2nd open position for improved access to the com- partment. Push the lid down to close.
WARNING
Keep storage bins closed while driving to help prevent injury in an accident or a sudden stop.
Instruments and controls 2-27
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
Passenger(cid:146)s side
LIC0500
LIC0518
PASSENGER SEAT STORAGE TRAY
(if so equipped)
Pull the tray to open it.
LIC0496
CENTER CONSOLE Storage tray The center console storage tray can be used to store a cellular telephone and other small items. A coin holder is also located inside the tray. Pull the latch to open the tray to the 1st or 2nd position. Push the tray to close.
WARNING
The storage tray should not be used while driving so full attention may be given to vehicle operation.
2-28 Instruments and controls
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
LIC0731
LIC0732
WIC0840
Portable devices
WARNING
Portable devices should not be used while driving so full attention may be given to vehicle operation.
For portable devices, such as cellular phones, a power cord can be routed to the power outlet inside the lower storage bin through the notch on the side of the tray. s1 Open the lower storage bin. Plug the por- table device charger into the power outlet and into the portable device.
s2 Open the storage tray. s3 Close the lower storage bin, using care not
to pinch the cord.
s4 With the access hole covers sA removed, adjust the divider and insert the portable device upright, allowing the portable device connector to pass through the hole in the storage tray. To prevent damage to the portable device cord, do not route the cord through the hole in the storage tray or attempt to close the storage tray with the portable device charger connected.
Lower storage bin Open the lower storage bin by pressing the but- ton down. Push the lid up to close.
Instruments and controls 2-29
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
c Do not leave sunglasses in the sun- glasses holder while parking in direct sunlight. The heat may damage the sunglasses.
LIC0499
LIC0508
GLOVE BOX Open the glove box by pulling the handle. Use the master key when locking s1 or unlocking s2 the glove box. The valet key cannot be used to lock or unlock the glove box.
WARNING
Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.
2-30 Instruments and controls
SUNGLASSES HOLDER To open the sunglasses holder, push and release.
WARNING
c The sunglasses holder should not be used while driving so full attention may be given to vehicle operation.
c Keep the sunglasses holder closed
while driving to prevent an accident.
CAUTION
c Do not use for anything other than
sunglasses.
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
LIC0502
LIC0519
LIC0520
CONVENIENCE HOOK Use the convenience hook to store items such as a purse, hat or small trash bag.
CAUTION
Do not apply a total load of more than 10
lbs (4.5 kg) to the convenience hook.
Front door
MAP POCKETS
Sliding door
Instruments and controls 2-31
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
LIC0503
LIC0504
LIC0505
SEATBACK POCKETS The seatback pockets are located on the back of the driver(cid:146)s and passenger(cid:146)s seats. The pockets can be used to store maps.
GROCERY HOOKS The grocery hooks allow for standard size plastic grocery bags to hang side by side.
CAUTION
Do not apply a total load of more than 18
lbs (8 kg) to a single grocery hook.
UMBRELLA HOLDER The net located on the back of the driver(cid:146)s seat can be used to hold an umbrella. Slide the um- brella in and out of either end.
2-32 Instruments and controls
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
LIC0513
LIC0512
Small storage bin Push the button to open the small storage bin. Push the lid up to close.
OVERHEAD CONSOLE
WARNING
Keep storage bins closed while driving to help prevent injury in an accident or a sudden stop. Large storage bin Push the button to open the storage bin. Use the net to keep small items in place. Push the lid up to close.
Instruments and controls 2-33
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
WIC0833
LIC0509
Front row
CAUTION
c Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger.
CUP HOLDERS To open the front cup holders, push the button. The lid springs open automatically. Push the lid to the full open position. Fold up the second cup holder ring, if desired. To close, pull the entire cupholder unit up to the original position.
WARNING
The cup holder should not be used while driving so full attention may be given to vehicle operation.
2-34 Instruments and controls
2nd row
CAUTION
c Use only soft cups in the cup holder. Hard objects can injure you in an accident.
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
LIC0521
LIC0507
LIC0506
Sliding door bottle holder
3rd row
CAUTION
c Do not use bottle holder for any other objects that could be thrown about in the vehicle and possibly injure people during sudden braking or an accident. c Do not use bottle holder for open liquid
containers.
3RD ROW ARMREST BIN Raise the lid to open the 3rd row armrest bin.
Instruments and controls 2-35
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
LIC0514
LIC0511
WIC0831
CARGO AREA STORAGE BIN To open the cargo area storage bin, turn the knob counterclockwise s1 . The lid can be removed. To close, replace the lid and turn the knob clock- wise s2 .
Type A
Type B
GARMENT HOOK To store garments, pull the garment hook down to the use position.
CAUTION
Do not apply a total load of more than 55
lbs (25 kg) to the hook.
2-36 Instruments and controls
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
LIC0522
HEAD RESTRAINT STORAGE The storage bag can be used to store up to three head restraints or other items. The bag can be retained on the universal fasten- ers located on the trim in the cargo area.
CAUTION
c The cargo contained in the storage bag
must not exceed 5 lbs (2.2 kg).
c Do not apply a total load of more than 55 lbs (25 kg) to the universal fasteners.
ROOF RACK Always distribute the luggage evenly on the roof rack. Do not load more than 125 lb (56 kg). Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or its Gross Axle Weight Rating (GAWR front and
LIC0530
rear). The GVWR and GAWR are located on the
Safety Compliance Certification Label (located
on the driver(cid:146)s door pillar). For more information
regarding GVWR and GAWR, refer to (cid:147)Vehicle
loading information(cid:148) in the (cid:147)Technical and con-
sumer information(cid:148) section later in this manual.
Instruments and controls 2-37
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
WINDOWS
POWER WINDOWS
WARNING
c Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows.
c Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls and become trapped in a window. Unattended chil- dren could become involved in serious accidents.
The front and rear cross bars (if so equipped) can be adjusted forward and backward by loosening the TorxT head fastener s1 with the tool provided in the jack tool kit. Place your luggage on the bars, adjust the bars, and secure the luggage with rope to the utility loops s2 on the bars. Always check the tightness of the crossbar TorxT head fasteners.
WARNING
Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, un- secured cargo could cause personal injury.
CAUTION
Use care when placing or removing items from the roof rack. If you cannot comfort- ably lift the items onto the roof rack from the ground, use a ladder or stool.
LIC0489
5.
1. Window lock button 2. 3. 4.
Power door lock switch Front passenger side automatic switch Right rear power vent window switch (if so equipped) Left rear power vent window switch (if so equipped) Driver side automatic switch
6. Driver(cid:146)s side power window switch The driver(cid:146)s side control panel is equipped with switches to open or close all of the windows.
2-38 Instruments and controls
The power windows operate when the ignition
switch is in the ON position, or for about 45
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
seconds after the ignition switch is turned to the OFF position. If the driver(cid:146)s or passenger(cid:146)s door is opened during this period of about 45 sec- onds, power to the windows is canceled. To open a window, push the switch and hold it down. To close a window, pull the switch and hold it up. To stop the opening or closing function at any time, simply release the switch.
LIC0490
Front passenger power window switch
The passenger window switch operates only the
corresponding passenger window. To open the
window, push the switch and hold it down s1 . To
close the window, pull the switch up s2 .
Locking passengers(cid:146) windows
When the window lock button is depressed, only
the driver side window can be opened or closed.
Push it again to cancel the window lock function.
LIC0410
Automatic operation To fully open a window equipped with automatic operation, press the window switch down (only driver(cid:146)s side shown) to the second detent and release it; it need not be held. The window auto- matically opens all the way. To stop the window, lift the switch up while the window is opening.
To fully close a window equipped with automatic operation, pull the switch up to the second detent and release it; it need not be held. Auto-reverse function The auto-reverse function can be activated when a window is closed by automatic operation.
Instruments and controls 2-39
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the window oc- curs.
WARNING
There are some small distances immedi- ately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the window.
If the control unit detects something caught in a window equipped with automatic operation as it is closing, the window will be immediately low- ered.
2-40 Instruments and controls
LIC0523
LIC0524
POWER VENT WINDOWS (if so equipped) Use the vent window switches on the driver(cid:146)s side window controls to open and close the power vent windows. To open a power vent window, press the switch down s1 . To close the window, lift the switch up s2 . The power vent windows operate when the igni- tion key is in the ON position, or for 45 seconds after the ignition key is turned to the OFF position. If the driver(cid:146)s or passenger(cid:146)s door is opened during this 45 second period, power to the vent windows is cancelled.
MANUAL VENT WINDOWS (if so equipped) To open a manual vent window, pull the latch handle toward you until it releases. To lock the window in the open position, push the latch handle rearward until it locks. To close a manual vent window, pull the latch handle toward you and push the rear portion of the latch toward the rear of the vehicle until it locks.
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
SKYVIEW(cid:153) ROOF (if so equipped)
SUNROOF (if so equipped)
LIC0525
To close the skyview roof sunshade, pull the tab
to draw out the shade. Lock the shade in place by
positioning the rod on the holder.
To open the shade, lift the rod from the holder and
ease the shade back into its stored position.
CAUTION
Do not pull the skyview roof sunshade straight down. This can damage the shade.
LIC0473
AUTOMATIC SUNROOF The sunroof will only operate when the ignition key is in the ON position. The automatic sunroof is operational for about 45 seconds, even if the ignition key is turned to the ACC or OFF position. If the driver(cid:146)s door or the front passenger(cid:146)s door is opened during this period of about 45 sec- onds, power to the sunroof is canceled. Sliding the sunroof To open the sunroof, slide the switch to the OPEN position. When the sunroof is tilted up, it will automatically tilt down and then open.
To close the sunroof, slide the switch to the CLOSE position.
The position of the sliding sunroof lid can be chosen by the position of the sliding switch.
To fully open or close the sunroof, move the switch completely to the OPEN or CLOSE posi- tion. Tilting the sunroof To tilt the sunroof up, push the tilt switch to the UP position. When the roof is open, it will auto- matically close and then tilt up. To tilt the sunroof down, push the tilt switch to the DOWN position. Restarting the sunroof sliding switch The sliding switch will become inoperable after the battery terminal is disconnected, the electri- cal supply interrupted and/or some abnormality detected. Use the following reset procedure to return sunroof operation to normal.
1.
If the sunroof lid is open, push the tilting switch repeatedly toward DOWN to fully close the lid.
2. Finally, push and hold the tilting switch for more than 2 seconds toward DOWN to reestablish the lid(cid:146)s home position.
The sunroof should now operate normally.
Instruments and controls 2-41
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
If the sunroof does not close Have your NISSAN dealer check and repair the sunroof.
Auto reverse function (when closing or tilting down the sunroof) The auto reverse function can be activated when the sunroof is closed or tilted down by automatic operation when the ignition key is in the ON position or for about 45 seconds after the ignition key is turned to the OFF position. Depending on the environment or driving conditions, the auto reverse function may be activated if an impact or load similar to something being caught in the sunroof oc- curs.
WARNING
There are some small distances immedi- ately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the sunroof.
When closing: If the control unit detects something caught in the sunroof as it moves to the front, the sunroof will immediately open backward. When tilting down: If the control unit detects something caught in the sunroof as it tilts down, the sunroof will immedi- ately tilt up. 2-42 Instruments and controls
If the auto reverse function malfunctions and re- peats opening or tilting up the sunroof, keep pushing the tilt down switch within 5 seconds after it happens, then the sunroof will fully close gradually. In this case, make sure nothing is caught in the sunroof.
WARNING
c In an accident you could be thrown from the vehicle through an open sunroof. Always use seat belts and child restraints.
c Do not allow anyone to stand up or extend any portion of their body out of the sunroof opening while the vehicle is in motion or while the sunroof is closing.
CAUTION
c Remove water drops, snow, ice or sand
from the sunroof before opening.
c Do not place heavy objects on the sun-
roof or surrounding area.
Sunshade Open and close the sunshade by sliding it for- ward or backward.
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
NOTE: The foot well and door step lights illumi- nate when the driver and passenger doors are open regardless of the lights on de- mand switch position. These lights will turn off automatically after 30 minutes while doors are open to prevent the battery from becoming discharged.
LIGHTS ON DEMAND SWITCH
LIC0472
The lights on demand switch allows the driver to
select one of three lighting modes for the interior
lights and puddle lamps (if so equipped). The
lights on demand switch operates regardless of
ignition switch position.
: The interior lights and puddle lamps (if so equipped) illuminate. The lights will turn off auto- matically after 30 minutes to prevent the battery from becoming discharged.
OFF: The interior lights and puddle lamps (if so equipped) do not illuminate.
: The interior lights and puddle lamps (if so
equipped) illuminate when a door is opened.
If the lights on demand switch is in the position, the lights will stay on for about 30 sec- onds when: c The doors are unlocked by the keyfob, a key or the power door lock switch while all doors are closed and the ignition switch is in the OFF position.
c The driver(cid:146)s door is opened and then closed while the key is removed from the ignition switch.
c The key is removed from the ignition switch
while all doors are closed.
The interior lights and puddle lamps (if so equipped) will turn off while the 30 second timer is activated when: c The driver(cid:146)s door is locked by the keyfob, a
key, or the power door lock switch.
c The ignition switch is turned ON. The lights will turn off automatically after 30 min- utes while doors are open to prevent the battery from becoming discharged.
Instruments and controls 2-43
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
PERSONAL LIGHTS
Type A
Type B
Type C
LIC0492
LIC0493
LIC0492
The rear seating positions have personal lights located on the headliner or on the overhead con- sole. There is also a light above the cargo area on the overhead trim. To operate a personal light located on the head- liner (Type A), push the light.
The personal lights on the overhead console (Type B) can be swiveled 360 degrees. To turn on the light, press the button. Press the button again to turn off the light.
The cargo light on the overhead trim (Type C) has a three-position switch. To operate, push the light. On: The light is illuminated Normal: The light illuminates when any door is opened or unlocked by the keyfob. The light turns off after 30 seconds or when all doors are closed. Off: The light does not illluminate, regardless of door position or lock status.
2-44 Instruments and controls
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
MAP LIGHTS
LIC0491
LIC0832
To turn the map lights on, press the switches. To turn them off, press the switches again.
CAUTION
Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.
CONSOLE LIGHT The console light s1 will turn on whenever the parking lights or headlights are illuminated.
HOMELINKT UNIVERSAL TRANSCEIVER (if so equipped)
The HomeLinkT Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLinkT Universal Transceiver: c Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and se- curity systems.
c Is powered by your vehicle(cid:146)s battery. No separate batteries are required. If the vehi- cle(cid:146)s battery is discharged or is discon- nected, HomeLinkT will retain all program- ming.
Once the HomeLinkT Universal Transceiver is programmed, retain the original trans- mitter for future programming procedures (Example: new vehicle purchases). Upon sale of the programmed HomeLinkT Universal Transceiver buttons should be erased for security purposes. For additional information refer to (cid:147)Program- ming HomeLinkT(cid:148) later in this section.
the vehicle,
Instruments and controls 2-45
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
WARNING
c Do not use the HomeLinkT Universal Transceiver with any garage door opener that lacks safety stop and re- verse features as required by federal safety standards. (These standards be- came effective for opener models manufactured after April 1, 1982). A ga- rage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death.
c During the programming procedure your garage door or security gate will open and close (if the transmitter is within range). Make sure that people or objects are clear of the garage door, gate, etc. that you are programming.
c Your vehicle(cid:146)s engine should be turned off while programming the HomeLinkT Universal Transceiver.
2-46 Instruments and controls
LIC0526
PROGRAMMING HOMELINKT
1. To begin, press and hold the two outer
HomeLinkT buttons (to clear the memory)
until the indicator light s1 blinks (after 20
seconds). Release both buttons.
2. Position the end of the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLinkT surface.
LIC0527
3. Using both hands, simultaneously press and
hold both the HomeLinkT button you want to
program and the hand-held transmitter but-
ton.
DO NOT release the buttons until step 4 has been completed.
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
4. Hold down both buttons until the indicator light on the HomeLinkT flashes, changing from a (cid:147)slow blink(cid:148) to a (cid:147)rapidly flashing blink(cid:148). This could take up to 90 seconds. When the indicator light flashes rapidly, both buttons may be released. The rapidly flash- ing light indicates successful programming. To activate the garage door or other pro- grammed device, press and hold the pro- grammed HomeLinkT button (cid:151) releasing when the device begins to activate. If the indicator light on the HomeLinkT blinks rapidly for 2 seconds and then turns solid, HomeLinkT has picked up a (cid:147)rolling code(cid:148) garage door opener signal. You will need to proceed with the next steps to train the HomeLinkT to complete the programming which may require a ladder and another per- son for convenience.
5.
6. Press and release the (cid:147)smart(cid:148) or (cid:147)learn(cid:148) pro- gram button located on the garage door opener(cid:146)s motor to activate the (cid:147)training mode(cid:148). This button is usually located near the antenna wire that hangs down from the motor. If the wire originates from under a light lens, you will need to remove the lens to access the program button.
NOTE: Once you have pressed and released the program button on the garage door open- er(cid:146)s motor and the (cid:147)training light(cid:148) is lit, you have 30 seconds in which to perform step 7. Use the help of a second person for conve- nience to assist when performing this step. 7. Within 30 seconds of pressing and releas- ing the garage door opener program button, quickly and firmly press and release the HomeLinkT button you(cid:146)ve just programmed. Press and release the HomeLinkT button up to 3 times to complete the training.
8. Your HomeLinkT button should now be pro- grammed. (To program the remaining HomeLinkT buttons for additional door or gate openers, follow steps 2-8 only.)
all
previously
NOTE: Do not repeat step 1 unless you want to (cid:147)clear(cid:148) programmed HomeLinkT buttons. If you have any questions or are having difficulty programming your HomeLinkT buttons, please refer at: www.homelink.com or call 1-800-NISSAN-1 (1- 800-647-7261).
the HomeLinkT web
site
to
PROGRAMMING HOMELINKT FOR CANADIAN CUSTOMERS Prior to 1992, D.O.C. regulations required hand- held transmitters to stop transmitting after 2 sec- onds. To program your hand-held transmitter to HomeLinkT, continue to press and hold the HomeLinkT button (note steps 2 - 4 under (cid:147)Pro- gramming HomeLinkT(cid:148)) while you press and re- press ((cid:147)cycle(cid:148)) your hand-held transmitters every 2 seconds until the indicator light flashes rapidly (indicating successful programming).
NOTE: When programming a garage door opener, etc., it is advised to unplug the device dur- ing the (cid:147)cycling(cid:148) process to prevent pos- sible damage to the garage door opener components. OPERATING THE HOMELINKT UNIVERSAL TRANSCEIVER The HomeLinkT Universal Transceiver (once pro- grammed) may now be used to activate the ga- rage door, etc. To operate, simply press the ap- propriate programmed HomeLinkT Universal Transceiver button. The red indicator light will illuminate while the signal is being transmitted.
Instruments and controls 2-47
Z REVIEW COPY—2005 Quest (van) Owners Manual—USA_English (nna) 07/21/04—debbie X
PROGRAMMING TROUBLE- DIAGNOSIS If the HomeLinkT does not quickly learn the hand- held transmitter information: c replace the hand-held transmitter batteries
with new batteries.
c position the hand-held transmitter with its from the
facing
away
battery HomeLinkT surface.
area
c press and hold both the HomeLinkT and hand-held transmitter buttons without inter- ruption.
c position the hand-held transmitter 1 - 3
inches (26 - 76 mm) away from the
HomeLinkT surface. Hold the transmitter in
that position for up to 15 seconds.
If
HomeLinkT is not programmed within that
time, try holding the transmitter in another
position (cid:150) keeping the indicator light in view
at all times.
If you continue to have programming difficulties, please contact the NISSAN Consumer Affairs Department. The phone numbers are located in the Foreword of this manual.
2-48 Instruments and controls
CLEARING THE PROGRAMMED
INFORMATION
Individual buttons cannot be cleared. However,
to clear all programming, press and hold the two
outside buttons and release when the indicator
light begins to flash (approximately 20 seconds).
REPROGRAMMING A SINGLE
HOMELINKT BUTTON
To reprogram a HomeLinkT Universal Transceiver
button, complete the following.
1. Press and hold the desired HomeLinkT but-
ton. Do not release the button until step 4
has been completed.
2. When the indicator light begins to flash
slowly (after 20 seconds), position the
hand-held transmitter 1 - 3 inches (26 - 76
mm) away from the HomeLinkT surface.
3. Press and hold the hand-held transmitter
button.
4. The HomeLinkT indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons.
The HomeLinkT Universal Transceiver button has now been reprogrammed. The new device can be activated by pushing the HomeLinkT button that was just programmed. This procedure will not af- fect any other programmed HomeLinkT buttons.
IF YOUR VEHICLE IS STOLEN If your vehicle is stolen, you should change the