2002 Nissan Quest Owners Manual

To reset a fully or partially tilted, or closed sunroof: 1. Push and hold the UP/CLOSE side of the the sunroof stops

sunroof switch until tilting up, then release the switch.

2. Push and hold the DOWN/OPEN side of the switch until the sunroof lowers com- pletely. The sunroof is now reset and should operate correctly.

Sliding the sunroof To open the roof, push and hold the OPEN side of the switch. To close the roof, push and hold the CLOSE side. Tilting the sunroof To tilt up, first close the sunroof, then push the UP side of the switch. To close the sunroof, push the DOWN side of the switch.

Sun shade Open and close the sun shade by sliding it forward or backward. The shade opens when the sunroof opens, but it must be closed manually.

WARNING

● In an accident you could be thrown from the vehicle through an open sunroof. Always use seat belts and child restraints.

● Do not allow anyone to stand up or extend any portion of their body out of the sunroof opening while the vehicle is in motion or while the sunroof is closing.

CAUTION

● Remove water drops, snow,

ice or sand from the sunroof before opening. ● Do not place any heavy object on the

sunroof or surrounding area.

Instruments and controls 2-33

墌 墍

INTERIOR LIGHTS

PERSONAL READING LIGHT

● When the switch is in the ON position, the interior light illuminates, whether any door is open or closed.

CAUTION

Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.

LUGGAGE When the back door is opened, the luggage compartment light and the rear interior light illuminate. When the back door is closed, the lights go off.

AIC0053

The interior lights operate regardless of ignition key position. One interior light is located overhead near the front seats and one is overhead near the rear seat. The interior switches: ● When the switch is in the OFF position, the interior light does not illuminate, re- gardless of door position.

lights have three-position

● When the switch is in the center O posi- tion, the light illuminates when a door is opened.

2-34 Instruments and controls

AIC1088

The driver’s side, second and third row seating positions have a personal reading light located in the overhead trim panel. To turn the light on, press once on the right-hand side of the light cover. To turn the light off, press again on the right-hand side of the light cover.

Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.

墌 墍

MAP LIGHTS

AIC1097

To turn on the map lights, press the switches. To turn them off, press the switches again.

Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.

ILLUMINATED ENTRY SYSTEM

The interior lights, the cargo light, the glove box light, the stepwell lights near the sliding doors and on the front doors, and the foot- well lights near the driver’s and front pas- senger’s feet illuminate when the front or sliding doors are opened. Once the doors are closed, these lights gradually dim to off within 30 seconds or turn off immediately when the key is turned to the ON position. Battery saver If the vehicle doors are not fully closed and the interior lights remain illuminated, they eventually turn off automatically to prevent the battery from becoming discharged. If the interior lights are left in the ON position, with all doors closed, they will automatically turn off after approximately 30 minutes. Lights that illuminate when the front or sliding doors are opened turn off after approxi- mately 30 minutes. Lights that illuminate when the back door is opened turn off after approximately 60 minutes. Vanity mirror lights are not part of the battery saver system. If the personal reading lights are left on after the key is removed from the ignition, they will automatically turn off after approxi- mately 30 minutes.

HomeLink姞 UNIVERSAL TRANSCEIVER (if so equipped) The HomeLink姞 Universal Transceiver pro- vides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. ● The HomeLink姞 Universal Transceiver will operate garage doors, gates, home/ office lighting systems and security sys- tems by storing and transmitting the pro- gramming information of your current hand-held transmitters.

● The HomeLink姞 Universal Transceiver is built-in and powered by your vehicle’s battery and charging system. No separate batteries are necessary.

WARNING

Do not use this HomeLink姞 Universal Transceiver with any garage door opener that lacks safety stop and re- verse features as required by federal safety standards (these standards be- came effective for models manufac- tured after April 1, 1982). A garage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse the

Instruments and controls 2-35

墌 墍

door, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death.

2-36 Instruments and controls

AIC1069

PROGRAMMING HomeLink姞

WARNING

During the programming procedure your garage door or security gate will open and close (if the transmitter is within range). Make sure that people or objects are clear of the garage door, gate, etc. that you are programming.

Your vehicle’s engine should be turned off while programming your transmit- ter. The HomeLink姞 Universal Trans- ceiver may not work with older garage door openers that do not meet current Federal Consumer Safety Standards.

1. Test

the HomeLink姞 Universal Trans- ceiver by pressing any button. The red indicator light should come on. If you have previously programmed a button proceed to step 3.

2. Clear all channels on the HomeLink姞 Universal Transceiver by holding down both outside buttons (#1 & #3) until the red light begins to flash rapidly (approxi- mately 20 seconds). Then release both buttons.

3. Select which of

the three HomeLink姞 Universal Transceiver buttons you want to program.

4. Hold your hand-held transmitter against the HomeLink姞 the bottom surface of Universal Transceiver so that you can still see the red indicator light.

墌 墍

5. Press the desired button until the red indicator light flashes slowly. Do not re- lease the button. Continue holding and press the hand-held transmitter button through step 6.

6. Hold down both buttons until

the red indicator light on the HomeLink姞 Univer- sal Transceiver flashes rapidly (This may take 1 to 90 seconds). Then release both buttons. The rapid flashing means that the transceiver has been successfully programmed to match your hand-held transmitter. You can now use the HomeLink姞 Universal Transceiver in- stead of your hand-held transmitter.

PROGRAMMING Homelink姞 FOR CANADIAN CUSTOMERS Prior to 1992, D.O.C. regulations required many hand-held transmitters to stop trans- mitting after one or two seconds, even though you continue to hold down the but- ton. these hand-held transmitters, you should press and re-press the transmitter button every 2
seconds without the HomeLink姞 Universal Transceiver button. The indicator light on the HomeLink姞 Uni- versal Transceiver should blink rapidly indi-

If you think you have one of

releasing

ever

● Hold buttons for duration of the program-

ming without interruption.

● Rotate your hand-held transmitter end- over-end and program again. For best results, place the end opposite the bat- tery the HomeLink姞 Universal Transceiver when programming.

compartment

against

cating a successful programming proce- dure. If it returns to the slow blink of program mode, continue to periodically reactivate your hand-held transmitter until a success- ful programming procedure is indicated by the rapidly flashing indicator light. OPERATING THE HomeLink姞 UNIVERSAL TRANSCEIVER To operate, simply press the appropriate button on the HomeLink姞 Universal Trans- ceiver. The red indicator light illuminates is being transmitted. The while the signal effective the HomeLink姞 Universal Transceiver may dif- fer from your hand-held transmitter. PROGRAMMING TROUBLE DIAGNOSIS Be sure to keep your original hand-held transmitter for possible reprogramming if necessary. ● Make sure batteries in the hand-held

transmission

range

of

transmitter are fully charged.

● Hold your hand-held transmitter against the HomeLink姞 the bottom surface of Universal Transceiver so that you can still see the red indicator light.

Instruments and controls 2-37

墌 墍

ROLLING CODE PROGRAMMING If your hand held transmitter appears to train to the HomeLink姞 Universal Trans- ceiver, but does not open your garage door, and your garage door opener was manufac- tured after 1995, your garage door opener may have a Code Protected or Rolling Code feature. This type of system will change the code of your garage door opener every time you open or close your garage door. these To determine if you have one of systems, depress the button on the HomeLink姞 Universal Transceiver that you have just programmed. If the LED on the HomeLink姞 Universal Transceiver flashes rapidly for 1 to 2 seconds, then remains on, your garage door opener has a rolling code system. To operate your rolling code garage door from your HomeLink姞 Universal opener Transceiver, follow these steps: 1. Program your hand held transmitter to the HomeLink姞 Universal Transceiver by following the procedures outlined previ- ously (if not yet programmed).

2. Program your garage door opener re- ceiver to recognize the HomeLink姞 Uni-

AIC1070

CLEARING THE PROGRAMMED INFORMATION Should you sell your vehicle, be sure to clear the channels of the HomeLink姞 Uni- versal Transceiver. To clear the channels, simultaneously hold down the outside two buttons (#1 & #3) until the red indicator light begins to flash rapidly (approximately 20
seconds). This will clear all three buttons. Individual buttons cannot be cleared, but can be reprogrammed at any time by follow- ing the programming procedures described previously.

2-38 Instruments and controls

versal Transceiver (The HomeLink姞 Uni- versal Transceiver follows the same procedure to train to the receiver as your hand held transmitter did when it was first installed): a) Remove the cover panel

from your garage door opener receiver. The re- ceiver should be located by the ga- rage door opener motor.

b) Locate the training button on the ga- rage door opener receiver. The exact location and color of the button may vary by garage door opener brand. If you have difficulty locating the training button, reference your garage door opener manual. If you have difficulty programming door opener equipped with a rolling code system to recognize the HomeLink姞 Universal Transceiver with the Rolling Code feature, call NISSAN Consumer Affairs Department.

garage

your

c) Press the training button on the ga- rage door opener receiver for 1 to 2
seconds.

墌 墍

FFC Notice: This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that may be received, including interference that may cause undesired operation. The transmitter has been tested and complies with FCC and DOC/MDC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s author- ity to operate the device. DOC: ISTC 1763K1313
FCC I.D.: CB2V67690

d) Return to the HomeLink姞 Universal Transceiver in the vehicle, and de- press the programmed HomeLink姞 button for the duration of the fast blink on the HomeLink姞 Universal Trans- ceiver (1 to 2 seconds). Release the button, and repress to confirm that the system has trained.

e) Your garage door opener should now recognize your HomeLink姞 Universal Transceiver. You may use either your HomeLink姞 Universal Transceiver or your original hand held transmitter to open your garage door.

IF YOUR VEHICLE IS EVER STOLEN If your vehicle has been stolen, you should change the codes of any device that was programmed into the HomeLink姞 Universal Transceiver as soon as possible. Consult the owners manual of each device, or call the manufacturer or dealer of those devices. When your vehicle is recovered, you will have to reprogram the HomeLink姞 Uni- versal Transceiver with your new trans- mitter information.

Instruments and controls 2-39

墌 墍

MEMO

2-40 Instruments and controls

墌 墍

3 Pre-driving checks and adjustments

Keys .......................................................................3-2
Doors......................................................................3-2
Locking with key................................................3-3
Locking with inside lock knob............................3-3
Locking with power door lock switch.................3-4
Child safety sliding door locks...........................3-5
Remote keyless entry system................................3-6

How to use remote keyless entry system ...............................................................3-6
Battery replacement ..........................................3-8
Hood.......................................................................3-9
Rear door .............................................................3-10

Fuel filler lid..........................................................3-10
Opener operation ............................................3-10
Fuel filler cap...................................................3-10
Steering wheel .....................................................3-11
Tilt operation....................................................3-11
Sun visors.............................................................3-12
Vanity mirror ....................................................3-12
Mirrors ..................................................................3-12

Memory driver seat and mirrors (if so equipped)................................................3-12
Inside mirror.....................................................3-13
Outside mirrors................................................3-14

墌 墍

KEYS

DOORS

WPD0088

A key number plate is supplied with your key. Record the key number and keep it in a safe place (such as your wallet), NOT IN THE CAR. NISSAN does not record key numbers so it is very important to keep track of your key number plate. A key number is necessary only when you have lost all vehicle keys and do not have one to duplicate. If you still have a key, this key can be duplicated by an authorized NISSAN dealer or locksmith shop.

3-2 Pre-driving checks and adjustments

Two keys are supplied with your vehicle — one has a plastic head and one is all metal. Both keys perform the same functions.

WARNING

● Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintention- ally opening the doors, and will help keep out intruders.

● Before opening any door, always look for and avoid oncoming traffic. ● Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls. Unattended children could become involved in serious accidents.

CAUTION

● Always use the door handle to open or close a sliding door. Do not at- tempt to open or close the doors by merely placing your hand on the door edge or door slide roller, as this may cause injury.

墌 墍

● Always be sure that hands and feet are clear of the door frame to avoid injury while closing a sliding door.

● When opening a sliding door on a slope, ensure that it is fully open and that it does not close by itself.

APD1057

LOCKING WITH KEY Turning the door key one time to the rear of the vehicle unlocks the corresponding door. From that position, returning the key to Neutral (where the key can only be removed and inserted) and turning it to the rear again within 5 seconds unlocks all doors. Turning the door key to the front of the vehicle locks all doors. The selective unlock function and locking all doors can be operated from the driver, passenger and rear door.

WPD0087

LOCKING WITH INSIDE LOCK KNOB To lock all doors from inside the vehicle, push the door lock knob in, then close the door. When locking the doors this way, be certain not to leave the key inside the ve- hicle. All doors automatically unlock if the key is in the ignition and a door is open.

Pre-driving checks and adjustments 3-3

墌 墍

APD1055

APD1074

LOCKING WITH POWER DOOR LOCK SWITCH Operating the lock-unlock switch locks or unlocks all doors. If the power door lock switch is pressed when a sliding door is open, the sliding door automatically locks when it is closed.

Sliding door To lock a sliding door from inside the ve- hicle, press the door lock rocker switch on the side marked L. To unlock, press the rocker switch on the side marked U. The driver side sliding door cannot be fully opened when the fuel door is open.

3-4 Pre-driving checks and adjustments

墌 墍

APD1075

CHILD SAFETY SLIDING DOOR LOCKS Child safety locking helps prevent doors from being opened accidentally, especially when small children are in the vehicle.

APD1056

When the lever is in the LOCK position, the sliding doors can be opened only from the outside.

Pre-driving checks and adjustments 3-5

墌 墍

REMOTE KEYLESS ENTRY SYSTEM

It is possible to lock/unlock all doors, turn the interior lights on or off, and activate the panic alarm by using the keyfob from out- side the vehicle. Be sure to remove the key from the vehicle before locking the doors and leaving it. The keyfob can operate at a distance of approximately 30 ft (10 m) from the vehicle. The effective distance depends on the con- ditions around the vehicle. As many as four keyfobs can be used with one vehicle. For more information concern- ing the purchase and use of additional key- fobs, contact an authorized NISSAN dealer.

CAUTION

Listed below are conditions or occur- rences which will damage the keyfob: ● Do not allow the keyfob to become

wet.

● Do not drop the keyfob. ● Do not strike the keyfob sharply

against another object.

3-6 Pre-driving checks and adjustments

● Do not place the keyfob for an ex- tended period in an area where tem- peratures exceed 140°F (60°C).

HOW TO USE REMOTE KEY- LESS ENTRY SYSTEM Locking doors 1. Close all doors. 2. Push the 3. All doors lock. 4. The parking lights flash twice and the horn chirps once to verify all doors are locked.

button on the keyfob.

Unlocking doors For memory seat and mirror information see ‘‘Memory driver seat and mirrors’’ later in this section. 1. Push the

button on the keyfob. Only the driver door unlocks. Parking lights flash once.

2. The interior lights come on and stay on

for 30 seconds.

3. Push the

button on the keyfob again

within five seconds. The passenger door, sliding doors, and the rear door unlock. The interior lights can be turned off without waiting 30 seconds by either turning the ignition to ON or locking the doors with the multi-remote controller. Using the panic alarm If you are near your vehicle and feel threat- ened, you may activate the panic alarm to call attention as follows: 1. Push and hold the

button on the

keyfob for at least one full second.

2. The theft warning alarm (horn) sounds and the headlights and tail lights flash for 30 seconds.

3. The panic alarm stops when: ● it has run for 30 seconds, or ● the ● the

or the button is pressed, or button is released and re-pushed.

墌 墍

The hazard lights will flash three times to confirm that the horn beep feature has been reactivated. Deactivating the horn feature does not si- lence the horn if the alarm is triggered.

AIC1037

Silencing the horn beep feature If desired, the horn beep feature can be deactivated using the keyfob. The instruc- tions are on the back of the keyfob. To deactivate: Press and hold the

and

buttons for at least two seconds.

The hazard lights will flash three times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the

and two seconds

buttons for at

least

once more.

Pre-driving checks and adjustments 3-7

墌 墍

BATTERY REPLACEMENT

BATTERY REPLACEMENT Replace the battery as follows: 1. Open the lid using a coin. 2. Replace the battery with a new one. Insert the batteries as illustrated above.

3-8 Pre-driving checks and adjustments

Recommended battery: CR2025, 3V or equivalent.

APD1087

Panasonic

3. Close the lid securely. 4. Press the

button, then the

button two or three times to check the keyfob opera- tion.

If the batteries are removed for any reason other than replacement, perform step 4. ● An improperly disposed battery can hurt the environment. Always conform to local regulations for battery disposal. ● The keyfob is water-resistant; how- ever, if it does get wet, immediately wipe completely dry.

● The operational range of the keyfob extends to approximately 30 ft (10 m) from the vehicle. This range may vary with conditions.

FCC Notice: Changes or modifications not expressly approved by the manufacturer for com- pliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference re- ceived, including interference that may cause undesired operation of the device.

墌 墍

HOOD

1. Pull

the hood lock release handle 䊊1
located below the instrument panel; the hood then springs up slightly.

2. Pull up on the lever 䊊2 at the front of the

hood and raise the hood.

WPD0053
3. Insert the support rod 䊊3 into the slot on

the underside of the hood.

4. When closing the hood, reset the support rod to its original position, lower the hood to approximately 12 inches above the latch and release it. This allows proper engagement of the hood latch.

WARNING

● Make sure the hood is completely closed and latched before driving. Failure to do so could cause the hood to fly open and result in an accident.

● If you see steam or smoke coming to

from the engine compartment, avoid injury do not open the hood.

Pre-driving checks and adjustments 3-9

墌 墍

REAR DOOR

FUEL FILLER LID

Key operation To unlock the rear door, turn the key coun- terclockwise. To open the rear door, lift up on the opener handle near the license plate. To close, lower and push the rear door down securely.

WARNING

Do not drive with the rear door or glass open. This could allow dangerous ex- haust gases to be drawn into the ve- hicle. See ‘‘Exhaust gas’’ in the ‘‘Start- ing and driving’’ section of this manual.

3-10 Pre-driving checks and adjustments

APD1065

WPD0011

To lock the rear door with the key, turn the key clockwise as shown in the illustration. Turning the key fully clockwise unlocks the rear window on models equipped with the flip-up rear window. The rear wiper auto- matically lowers when the key is turned fully clockwise. Do not force the wiper to lower by hand. To close the rear window, firmly push on the window until it locks in place. The rear wiper automatically returns to the original position.

OPENER OPERATION To open the fuel filler lid, grasp the right hand edge of the lid and pull. FUEL FILLER CAP filler cap is a ratcheting type. The fuel Tighten the cap clockwise until ratcheting clicks are heard. Ensure the plastic tether doesn’t get caught between the fuel filler cap and the fuel filler neck. The driver side sliding door cannot be fully opened when the fuel door is open. Make sure the driver side sliding door is

墌 墍

completely closed before opening the fuel door.

WARNING

● Gasoline is extremely flammable and highly explosive under certain con- ditions. You could be burned or se- riously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.

● Fuel may be under pressure. Turn the cap one-half turn, and wait for any ‘‘hissing’’ sound to stop to prevent fuel from spraying out and possibly causing personal injury. Then re- move the cap.

● Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refuel- ing may cause fuel overflow, result- ing in fuel spray and possibly a fire. ● Use only an original equipment type fuel filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emission control system. An

incorrect cap can result in a serious malfunction and possible injury.

● Never pour fuel into the throttle body

to attempt to start your vehicle.

CAUTION

● If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.

● Tighten until the fuel filler cap clicks. Failure to tighten the fuel filler cap properly may cause the mal- function indicator lamp (MIL) to illu- minate. If the lamp illuminates because the fuel filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The lamp should turn off after a few driving trips. If the lamp does not turn off after a few driving trips, have the vehicle inspected by an authorized NISSAN dealer.

● For additional information, see the ‘‘Malfunction indicator lamp (MIL)’’ in the ‘‘Instrument and controls’’ section earlier in this manual.

STEERING WHEEL

APD1051

TILT OPERATION Push the lock lever down and adjust the steering wheel up or down to the desired position. Pull the lock lever up firmly to lock the steering wheel in place. Gently pull down on the wheel to make sure it is properly locked.

WARNING

Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.

Pre-driving checks and adjustments 3-11

墌 墍

SUN VISORS

MIRRORS

WPD0012

APD1062

VANITY MIRROR Access the mirror by pulling the sun visor down and lifting the cover up. The vanity mirror will illuminate when the mirror cover is opened.

MEMORY DRIVER SEAT AND MIRRORS (if so equipped) The memory driver seat and mirror function provides a convenient way to recall a driv- er’s seat and outside mirror positions. Un- locking the doors using the multi-remote controller, or by pressing the memory seat position 1 or position 2 button activates the memory driver seat and mirrors. Remote keyless entry system entry Pressing the button on the keyfob un- locks the driver’s door, and recalls the memory settings for both outside mirrors

3-12 Pre-driving checks and adjustments

and driver’s seat for that memory position. Two keyfobs are delivered with the vehicle. They can be programmed with the same memory driver’s seat and mirror positions, or each one can be programmed sepa- rately. One keyfob can be programmed for memory driver’s seat and mirror position 1, and the other for memory driver’s seat and mirror position 2. Memory Driver Seat and Mirror But- tons The memory seat and mirror buttons are located on the driver door. Pressing the memory driver seat and mirror position 1 or position 2 button will recall the memory set- tings for both outside mirrors and driver seat for that memory seat position, provided the vehicle is in P (Park) or N (Neutral). For easy vehicle exit, press memory driver seat and mirror position 1 and position 2 buttons to- gether to move the driver seat fully rearward and fully downward. This function is preset and cannot be changed. Programming Memory Positions 1. Move the driver seat and outside mirrors to the desired position using the manual controls.

墌 墍

programmed. If the memory seat button is pressed and held the indicator light will remain illuminated for as long as the button is held or 10 seconds which ever is shorter. To remove a keyfob from the memory seat system press and hold both memory seat and mirror position buttons 1 and 2 and then press the

button on the keyfob.

2. Push and hold the memory seat and mirror position 1 or position 2 button for at least 3 seconds.

● The indicator light will illuminate and re- main illuminated until the position is pro- grammed.

● After the position has been programmed the indicator light will flash to indicate the position is set.

The driver seat and/or outside mirrors must be adjusted before programming position 1
or position 2. Programming a keyfob 1. Move the driver seat and outside mirrors by pressing the desired position 1 or position 2 button.

2. Press and hold the same (position 1 or

position 2) button.

3. Within 10 seconds press the

the keyfob.

button on

The keyfob is now programmed for that (position 1 or position 2) button. After the keyfob has been programmed, the memory seat and mirror button indicator light will flash to indicate the keyfob is

PD1006M

INSIDE MIRROR The night position reduces glare from the headlights of vehicles behind you at night.

WARNING

Use the night position only when nec- essary, because it reduces rear view clarity.

Pre-driving checks and adjustments 3-13

墌 墍

cause an accident. Use the inside mir- ror or glance over your shoulder to properly judge distances to other ob- jects.

Heated mirrors (Canada only) The electric control type outside mirrors can be heated to defrost, defog, or de-ice for improved visibility. Press the rear window defogger switch to activate the heating func- tion. Press the switch again to deactivate, or the heating function will automatically turn off after approximately 15 minutes.

M008

Foldable outside mirrors Push the outside mirrors backward to fold them.

APD1052

OUTSIDE MIRRORS The outside mirrors operate only when the ignition switch is in the ACC or ON position. Move the switch to select the right or left side mirror, then adjust using the control lever.

WARNING

Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could

3-14 Pre-driving checks and adjustments

墌 墍

4 Heater, air conditioner and audio systems

Ventilators ..............................................................4-2
Center ventilators ..............................................4-2
Side ventilators..................................................4-2
Heater and air conditioner (manual) ......................4-3
Controls .............................................................4-3
Heater operation................................................4-4
Air conditioner operation ...................................4-5
Air flow charts....................................................4-7

Heater and air conditioner (automatic) (if so equipped) ....................................................4-11
Automatic operation ........................................4-12
Rear seat air conditioner (if so equipped) ...........4-14
Controls ...........................................................4-14
Servicing air conditioning .....................................4-15
Audio system........................................................4-16
Radio ...............................................................4-16
FM radio reception ..........................................4-16
AM radio reception ..........................................4-16
Audio operation precautions ...........................4-17

FM-AM radio with cassette player...................4-20
FM-AM radio with cassette player and compact disc (CD) player................................4-26
Compact disc (CD) player (if so equipped).........................................................4-32
CD care and cleaning......................................4-33
Steering wheel switch for audio controls (if so equipped)................................................4-34
Rear audio controls (if so equipped)...............4-35
Antenna ...........................................................4-37

Autovision姞 family entertainment system (FES) (if so equipped)..........................................4-37

Rear seat entertainment module (RSEM) (if so equipped)..................................4-41
Care and maintenance....................................4-43
Troubleshooting...............................................4-44
Specifications ..................................................4-45
Car phone or CB radio.........................................4-46

墌 墍

VENTILATORS

AHA1056

AHA1055

CENTER VENTILATORS Open, close and adjust the air flow direction of ventilators.

SIDE VENTILATORS Open, close and adjust the air flow direction of ventilators.

: This symbol indicates a vent is closed when the vent switch is moved down. : This symbol indicates a vent is open

when the vent switch is moved up.

4-2 Heater, air conditioner and audio systems

墌 墍

HEATER AND AIR CONDITIONER (manual)

WARNING

leave children,

● The air conditioner cooling function operates only when the engine is running. ● Do not

impaired adults, or pets alone in your vehicle. On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or animals.

● Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

● Positioning of the heater and air con- ditioner controls should not be done while driving, so full attention may be given to vehicle operation.

WHA0008

Air flows mainly from the front and rear foot outlets. Air flows from defroster outlets and the front and rear foot outlets. Air flows mainly from defroster outlets. Air flows mainly from center and side ventilators.

MAX A/C

CONTROLS Fan control dial This dial controls fan speed. Air flow control dial This dial allows you to select the air flow outlets.

Air flows mainly from center and side ventilators. Air flows from center and side ventila- tors and the front and rear foot outlets.

Heater, air conditioner and audio systems 4-3

墌 墍

OFF position The OFF position shuts off the air supply to all outlets and stops all fan operations. Use the OFF position to prevent cold air from entering the passenger compartment under cold outside conditions before the engine is warmed up. MAX A/C Position Interior air is recirculated inside the vehicle. Turn the air control dial to the MAX A/C position when driving on a dusty road or to help keep out traffic fumes. to the MAX A/C Turn the air control dial position for improved air conditioner perfor- mance under high temperature and high hu- midity conditions.

CAUTION

Do not use the recirculation mode for long periods as it may cause the inte- rior air to become stale and the win- dows to fog up.

Air conditioning button Start the engine, turn the fan control dial to the desired (one to four) position, select an air control position and push the air condi- tioner button to turn on the air conditioner. The indicator light comes on when the air conditioner is operating. To stop the air con- ditioner, push the button again; the indicator light goes off. The air conditioner cooling function op- erates only when the engine is running. HEATER OPERATION Heating This mode is used to direct most of the hot air to the front and rear floor outlets. Rear passenger heat is provided by the front system through floor outlets located under both front seats. 1. Move the air control dial to the

po-

sition.

Temperature control dial This dial allows you to adjust the tempera- ture of the outlet air. 4-4 Heater, air conditioner and audio systems

2. Turn the fan control dial to select speed. 3. Move the temperature control dial to the

desired position.

Ventilation This mode directs air to the side and center vents. 1. Move the air control dial to the

po-

sition.

2. Turn the fan control dial to select speed. 3. Move the temperature control dial to the

desired position.

Defrosting or defogging This mode is used to defrost/defog the windows. 1. Move the air control dial to the

po-

sition.

2. Turn the fan control dial to select speed. 3. Move the temperature control dial to the

desired position. When the position is selected, the air conditioner automatically turns on (however, the indicator light will not illu- minate) the outside temperature is more than 45°F (7°C). This dehumidifies the air which helps defog the windshield. The air recirculation mode automatically turns off, allowing outside air to be drawn

if

墌 墍

into the passenger compartment which helps defog the windshield.

Bi-level heating/cooling The bi-level mode directs air to the side and center vents and to the front and rear floor outlets. Bi-level is also a cooling mode when high sun load conditions are present with cool temperatures. With the A/C system in operation, this mode can be used to cool the passenger’s or driver’s feet under high temperature condi- tions. With the A/C system in operation under high temperature conditions, improved cooling can be obtained by moving the air control dial to the MAX A/C position. 1. Move the air control dial to the

po-

sition.

2. Turn the fan control dial to the desired

position.

3. Move the temperature control dial to the

desired position.

Heating and defogging This mode heats the interior and defogs the windshield. This mode directs air to the defroster and the front and rear floor outlets. Rear passenger heat is provided by the front system through floor outlets located under both front seats. 1. Move the air control dial to the

po-

sition.

2. Turn the fan control dial to the desired

position.

3. Move the temperature control dial to the

if

desired position. When the position is selected, the air conditioner automatically turns on (however, the indicator light will not illu- minate) the outside temperature is more than 45°F (7°C). This dehumidifies the air which helps defog the windshield. The air recirculation mode automatically turns off, allowing outside air to be drawn into the passenger compartment which helps defog the windshield.

windshield. This improves heater op- eration.

● To defog the side windows more effec- tively when in bi-level or ventilation mode, close the center vent and direct the side vents toward the side windows. ● A slight delay may be experienced when changing air control buttons. The system is not malfunctioning. It is only the sys- tem motors and solenoids switching from one outlet to another.

AIR CONDITIONER OPERATION Start the engine, move the fan control dial to the desired (one to four) position, and select an air control position before pushing in the air conditioner button to activate the air conditioner. When the air conditioner is on, cooling and dehumidifying functions are added to the heater operation.

WARNING

The air conditioner cooling function op- erates only when the engine is running.

Operating tips ● Clear snow and ice from the wiper blades and air inlet in front of the

Heater, air conditioner and audio systems 4-5

墌 墍

NOTE: When switching air flow outlets, the A/C system remains activated unless the A/C button is pressed to the OFF position. The indicator light on the A/C button re- mains illuminated unless the button is pressed to the OFF position, or the OFF air control position is selected. Cooling This mode is used to cool and dehumidify. 1. Move the air control dial to the po-

sition.

2. Turn the fan control dial to select speed. 3. Push the air conditioner button. The indi-

cator light comes on.

4. Move the temperature control dial to the

desired position.

● For quick cooling when the outside tem- perature is high, move the air control dial to the MAX A/C position. Be sure to return the air control dial to the po- sition for normal cooling.

● Opening the windows helps to vent heat

buildup when parked in the sun.

Dehumidified heating This mode is used to heat and dehumidify. 1. Move the air control dial to the po-

sition.

2. Turn the fan control dial to select speed. 3. Push the air conditioner button. The indi-

cator light comes on.

4. Move the temperature control dial to the

desired position.

Dehumidified defogging This mode is used to defog the windows and dehumidify. 1. Move the air control dial to the

po-

sition.

2. Turn the fan control dial to the desired

speed.

3. Move the temperature control dial to the

desired position. When the position is selected, the air conditioner automatically turns on (however, the indicator light will not illu- minate) the outside temperature is more than 45°F (7°C). This dehumidifies the air which helps defog the windshield.

if

4-6 Heater, air conditioner and audio systems

The air recirculation mode automatically turns off, allowing outside air to be drawn into the passenger compartment which helps defog the windshield.

Operating tips ● Keep windows and sun roof closed while

the air conditioner is in operation.

● After parking in the sun, drive for two or three minutes with the windows open to vent hot air from the passenger compart- ment. Then, close the windows. This allows the air conditioner to cool the interior more quickly.

● The air conditioning system should be operated for about ten minutes at least once a month. This helps pre- vent damage to the system due to lack of lubrication.

● If the engine coolant temperature gauge exceeds the H (hot) position, turn the air conditioner off. See ‘‘If your vehicle over- heats’’ in the ‘‘In case of emergency’’ section for additional information.

墌 墍

AIR FLOW CHARTS The following charts show the button and dial positions for MAXIMUM AND QUICK heating, cooling or defrosting.

Heater, air conditioner and audio systems 4-7

WHA0009

墌 墍

4-8 Heater, air conditioner and audio systems

WHA0010

WHA0011

墌 墍

WHA0012

WHA0094

Heater, air conditioner and audio systems 4-9

墌 墍

4-10 Heater, air conditioner and audio systems

WHA0014

墌 墍

HEATER AND AIR CONDITIONER (automatic) (if so equipped)

WARNING

leave children,

● The air conditioner cooling function operates only when the engine is running. ● Do not

impaired adults, or pets alone in your vehicle. On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or animals.

● Do not use the recirculation mode for long periods as it may cause the

WHA0015

interior air to become stale and the windows to fog up.

● Positioning of the heater and air con- ditioner controls should not be done while driving, so full attention may be given to vehicle operation.

The Electronic Automatic Temperature Control (EATC) is located at the center of the instrument panel, below the radio. The EATC operates only when the ignition is turned to the ON position. The EATC maintains the temperature you

select and controls the airflow for your com- fort. It also allows you to override the auto- matic operation with manual function selec- tor buttons. To turn the EATC on, push either the AU- TOMATIC button or any of the six function selector buttons: or MAX. To turn the EATC off, press

the OFF button. When you select AUTOMATIC, the system determines fan speed, airflow location and discharge air temperature. When one of the function selector buttons is pressed, your selection determines airflow location only. Fan speed and discharge air temperature remain automatic. You can override fan speed by rotating the vertical thumbwheel the

the extreme right of

located at

control panel. The display window indicates the status of the system. It shows the selected tempera- ture and AUTO when in the AUTOMATIC mode. (thumb- the fan speed when a wheel) control of

It also indicates manual

is shown.

Heater, air conditioner and audio systems 4-11

墌 墍

side of

AUTOMATIC OPERATION Push the AUTOMATIC button and select the desired temperature. The selected tempera- ture and AUTO show in the display window. The EATC heats or cools to achieve the set temperature. When in AUTOMATIC and weather conditions require heat, air is sent to the floor. However, a feature is included in the EATC to prevent blowing cold air to the floor if the engine coolant is not warm enough to allow heating. In three or four minutes the fan speed gradu- ally increases and airflow changes to the floor. If unique conditions exist, such as window fogging, the five override buttons allow spe- cific airflow selection. The thumbwheel al- lows you to adjust the fan speed to suit your needs. Temperature selection The button on the left side of the control panel is for temperature selec- tion. The side lowers the set tempera- ture, and the side raises the set tem- perature. Press and hold either side of the button to rapidly change the temperature setting in one degree increments to either 65°F (18°C) or 85°F (29°C). If you want 4-12 Heater, air conditioner and audio systems

continuous maximum cooling, push the the TEMP button until 60°F (16°C) shows in the display window. The EATC cools at maximum and disregards the 60°F (16°C) setting until a warmer tempera- ture is selected. If you want continuous maximum heating, push the side of the TEMP button until 90°F (32°C) shows in the display window. The EATC provides maxi- mum heat regardless of the 90°F (32°C) setting until a cooler temperature is se- lected. Fan speed and thumbwheel Your EATC automatically adjusts the fan speed to the existing conditions. To control the fan speed yourself, use the thumbwheel located at the EATC control panel. Using the thumbwheel cancels the automatic fan speed control, and causes a to appear in the display window. Rotate the thumbwheel up for HI speeds and down for LO speeds. To return to auto fan control, press the AUTOMATIC button. Air flow control Your EATC has five buttons which allow you to make special selections. The buttons are

the extreme right side of

TEMP

grouped in the middle of the EATC panel and allow you to determine airflow location. Pressing any of the air control buttons changes airflow location only, and does not affect the ability of the system to control temperature or fan speed. Return to fully automatic operation by pushing the AUTO- MATIC button.

Push this button for airflow to the front and rear floor outlets and windshield at the same indicator light comes on, time. The and the display window shows the set tem- perature.

Push this button to obtain maximum airflow to the windshield. Adjust the temperature setting as required for defrosting. The indicator light comes on, and the display window shows the set temperature. When the outside temperature is about 45°F (7°C) or above, the air is dehumidified to prevent window fogging.

Push this button to select airflow through

墌 墍

the

panel

registers.

The instrument indicator light comes on, and the display window shows the set temperature. The EATC heats the air if the selected temperature is warmer than the outside air coming into the vehicle. However, the air is not cooled regardless of the temperature setting, unless the A/C button is selected.

Push this button to get air from the front and rear floor outlets and instrument panel ven- tilators at the same time. The indicator light comes on and the display window shows the set temperature. The EATC heats the air if the selected temperature is warmer than the outside air coming into the vehicle. However, the air is not cooled re- gardless of the temperature setting, unless the A/C button is selected.

Push this button to direct airflow to the front and rear floor outlets. The indicator light comes on, and the display window shows the set temperature. The EATC heats the air if the selected temperature is warmer than the outside air coming into the vehicle. However, the air is not cooled re-

gardless of the temperature setting, unless the A/C button is selected.

Push the MAX button to choose air recircu- lation. In this mode the EATC system recir- culates the air inside the vehicle rather than drawing air from outside. Air is distributed through the instrument panel ventilators similar to mode. Use this mode to rap- idly cool the vehicle, or to dehumidify the air inside the vehicle.

the inside of

Activate the air conditioner in any of the override modes listed above by pressing the A/C button. The A/C indicator light comes on to verify activation, and cooled air flows from the vents. Fan speed continues to be controlled by the EATC unless the fan speed thumbwheel is used to override.

AHA1143

English/metric mode Switch from English to metric temperature display by simultaneously pressing the and A/C buttons and holding the thumbwheel in upper position (HI) for one second.

WARNING

Do not switch temperature displays while driving so full attention may be given to vehicle operation.

Heater, air conditioner and audio systems 4-13

墌 墍

REAR SEAT AIR CONDITIONER (if so equipped)

CONTROLS Fan control dial This dial controls fan speed.

turns the fan on and off, and

To operate the rear seat air conditioner, the engine must be running. The rear seat air conditioner can be turned on and off from the front controls. If the rear seat fan control lever on the front panel is set to OFF, the rear air conditioner is turned off. If it is set to any of the fan speed positions, air is discharged from the rear vents at the corresponding speed. When the rear seat fan control lever on the front panel is set to REAR A/C, the rear seat passengers control their own fan speed. The rear seat air conditioner only works when the front seat air conditioner is operating. 4-14 Heater, air conditioner and audio systems

WHA0016

墌 墍

SERVICING AIR CONDITIONING

The air conditioning system in your NISSAN vehicle is charged with a refrigerant de- signed with the environment in mind. This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant are required when servicing your NISSAN air conditioner. Using improper refrigerants or lubricants causes severe damage to your air conditioning system. See ‘‘Air condition- ing system refrigerant and lubricant recom- mendations’’ in the ‘‘Technical and con- sumer information’’ section of this manual. An authorized NISSAN dealer is able to service your environmentally ‘‘friendly’’ air conditioning system.

WARNING

The air conditioner system contains refrigerant under high pressure. To avoid personal injury, any air condi- tioner service should be done by an experienced technician with proper equipment.

Heater, air conditioner and audio systems 4-15

墌 墍

AUDIO SYSTEM

running,

influences.

RADIO Turn the ignition key to ACC or ON and press the power on switch to turn on the If you listen to the radio with the radio. engine not the key should be turned to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains and other ex- ternal Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the vehicle may influence radio reception quality. Radio reception Your NISSAN radio system is equipped with state-of-the-art electronic circuits to en- hance radio reception. These circuits are designed to extend reception range, and to enhance the quality of that reception. However there are some general character- istics of both FM and AM radio signals that can affect radio reception quality in a mov- ing vehicle, even when the finest equipment is used. These characteristics are com- 4-16 Heater, air conditioner and audio systems

in a given reception area, pletely normal and do not indicate any malfunction in your NISSAN radio system. Reception conditions will constantly change because of vehicle movement. Buildings, terrain, signal distance and interference from other vehicles can work against ideal reception. Described below are some of the factors that can affect your radio reception. FM RADIO RECEPTION Range: FM range is normally limited to 25 to 30 miles (40 to 48 km), with monaural (single channel) FM having slightly more range than stereo FM. External influences may sometimes interfere with FM station reception even if the FM station is within 25
miles (40 km). The strength of the FM signal is directly related to the distance between the transmitter and receiver. FM signals follow a line-of-sight path, exhibiting many of the same characteristics as light. For example they will reflect off objects. Fade and drift: As your vehicle moves away from a station transmitter, the signals will tend to fade and/or drift. Static and flutter: During signal interference from buildings, large hills or due to antenna

position, usually in conjunction with in- creased distance from the station transmit- ter, static or flutter can be heard. This can be reduced by adjusting the treble control counterclockwise to reduce treble re- sponse. Multipath reception: Because of the reflec- tive characteristics of FM signals, direct and reflected signals reach the receiver at the same time. The signals may cancel each other, resulting in momentary flutter or loss of sound. AM RADIO RECEPTION AM signals, because of their low frequency, can bend around objects and skip along the ground. the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics. AM signals are also subject to interference as they travel from transmitter to receiver. Fading: Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings. It can also occur for several seconds during ionospheric turbu- lence even in areas where no obstacles exist. Static: Caused by thunderstorms, electrical

In addition,

墌 墍

power lines, electric signs and even traffic lights. AUDIO OPERATION PRECAU- TIONS Cassette player ● To maintain good quality sound, NISSAN recommends that you use cassette tapes of 60 minutes or shorter in length.

● Cassette tapes should be removed from the player when not in use. Store cassettes in their protective cases and away from direct sunlight, heat, dust, moisture or magnetic sources.

● Direct sunlight can cause the cas- sette to become deformed. The use of deformed cassettes may cause the cassette to jam in the player.

● Do not use cassettes that have peel- ing or loose labels. If used, the label could jam in the player.

● If a cassette has loose tape, insert a pencil through one of the cassette hubs and rewind the tape firmly.

Loose tape may cause jamming and wavering sound quality.

● Over a period of time, the playback head, capstan and pinch roller may gather a tape coating residue as the tape passes over the head. This resi- due accumulation can cause a weak or wavering sound and should be removed periodically with a head cleaning tape. If the residue is not removed periodi- cally, the player may need to be dis- assembled for cleaning.

LHA0099

Compact Disc (CD) Player ● Only use high quality 4.7 inches (12
cm) round discs that have the ‘‘COM- PACT disc DIGITAL AUDIO’’ logo on the disc or packaging.

Heater, air conditioner and audio systems 4-17

墌 墍

● CDs with a paper label ● CDs that are warped, scratched, or

have abnormal edges

● During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CD and dehumidify or ventilate the player completely.

● The player may skip while driving on

rough roads.

● The CD player sometimes cannot function when the compartment tem- perature is extremely high. Decrease the temperature before use.

● Do not expose the CD to direct sun-

light.

● CDs that are of poor quality, dirty, scratched, covered with fingerprints, or that have pin holes may not work properly.

● Do not use the following CDs as they may cause the CD player to malfunc- tion: ● 8 cm (3.1 in) discs with an adapter ● Recordable compact discs (CD-R) ● Rewritable compact discs (CD-RW) ● CDs that are not round

4-18 Heater, air conditioner and audio systems

墌 墍

1. VOLUME - ON/OFF control 2. BASS/TREBLE select button 3. BASS/TREBLE/BALANCE/FADE control

button

4. BALANCE/FADE select button 5. Tape eject button 6. CLOCK button 7. SCAN button 8. AUTO SET button 9. Radio tune button 10. SHUFFLE/station memory #6 button 11. COMPRESSION/station #5 memory

button

12. Dolby/station memory #4 button 13. Tape reverse/station memory #3 button 14. FAST FORWARD/station memory #2

button

15. REWIND/station memory #1 button 16. FM band select button 17. AM band select button 18. SEEK button 19. MUTE button 20. CD button 21. TAPE button

WHA0138

Heater, air conditioner and audio systems 4-19

墌 墍

FM-AM RADIO WITH CASSETTE PLAYER NOTE: Audio control features include com- mand buttons for CD players which can be installed as optional equipment to upgrade the audio system. A CD player is not in- cluded with this system, but can be pur- chased as an option at any time. Consult with an authorized NISSAN dealer for fea- ture availability. Audio main operation To turn the radio on, turn the ignition key to ACC or ON. If you listen to the radio with the engine not running, turn the key to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains, and other external influences. Intermittent changes in reception quality normally are caused by external influences. Using a cellular phone in or near the vehicle may influence radio reception quality.

Power/Volume control Push the VOL knob to turn the radio on. Push the VOL knob once more to turn the radio OFF. Turn the knob to the right to increase vol- ume or to the left to decrease volume. If the knob is set above a certain volume level and the ignition is turned off, the volume will come back on at a nominal listening level when the ignition is turned back on. Adjusting tone quality and speaker bal- ance Bass Bass control allows you to adjust the lower, bass frequencies to your preference. Push the BASS button and the setting indi- cator bar appears in the display window. or Pressing the SELECT button either increases or decreases the level of bass, as indicated by the number of bar segments showing in the display window. Following bass adjustment, the display win- dow shows the current setting for three seconds, then returns to the display prior to adjustment.

the treble frequencies to your prefer-

Treble Treble control allows you to adjust higher, ence. Push the TREB button and the setting indi- cator bar appears in the display window. Pressing the SELECT button either or increases or decreases the level of treble, as indicated by the number of bar segments showing in the display window. Following treble adjustment, the display window shows the current setting for three seconds, then returns to the display prior to adjustment. Balance Balance control allows you to adjust the sound distribution between the right and left speakers. Push the BAL button and the setting indica- tor bar appears in the display window. Press the SELECT button to shift the sound to the right speakers. The single indicator bar moves to the right of the display win- dow. Press the SELECT button to shift the sound to the left speakers. The single indicator bar moves to the left of the display

4-20 Heater, air conditioner and audio systems

墌 墍

window. When the indicator bar is in the center position the sound is equally distrib- uted between the right and left speakers. Following balance adjustment, the display window shows the current setting for three seconds, then returns to the display prior to adjustment. Fader Fader control allows you to adjust sound distribution between the front and rear speakers. Push the FADE button and the setting indi- cator bar appears in the display window. Press the SELECT button to shift the sound to the front speakers. The single indicator bar moves to the right of the dis- play window. Press the SELECT button to shift the sound to the rear speakers. The single indicator bar moves to the left of the display window. When the indicator bar is in the center position the sound is equally distributed between the front and rear speakers. Following fader adjustment, the display win- dow shows the current setting for three seconds, then returns to the display prior to adjustment.

COMP button Press this button to activate the compres- sion function. This reduces the dynamic range, which provides the listener with a more consistent level of volume. The dis- play window shows a C when the COMP button is pushed. Clock operation The clock is on in the display regardless of what mode, media, or function the radio is in as long as the ignition is in ACC or ON. Clock set Press the RDS/CLK button until SELECT HOURS is displayed then use the SEL buttons to change the hour, press the RDS/CLK button again until SELECT MINS is displayed then use the SEL buttons to change the minutes. The display will return to clock priority mode in 10 seconds or press the RDS/CLK button to return to the clock display. Selecting the desired band Push the AM or FM buttons to change to AM or FM band reception. The FM stereo indicator, ST illuminates during FM stereo reception. When the stereo broad- cast signal is weak, the radio automatically

changes from stereo to monaural reception. FM-AM radio operation MUTE button Push the MUTE button to mute out radio. TUNE buttons

the

WARNING

The radio should not be tuned while driving so full attention may be given to vehicle operation.

or

Use the buttons for manual tuning. To move quickly through the chan- nels, hold either of the tune buttons down for more than 0.5 seconds. AUTO SET Press the AUTO button while listening to the radio to activate the auto set feature. When AUTO is depressed for less than 5 seconds, the display window momentarily indicates AUTO ON, and the radio seeks the first six strong stations for the respective band. The first six strong stations are then stored in order in memory buttons one through six.

Heater, air conditioner and audio systems 4-21

墌 墍

the highest

tinues in the SEEK mode at station. SCAN tuning Push the SCAN tuning button, SCAN illumi- nates in the display. SCAN tuning begins from low to high frequencies and stops at each broadcasting station for 5 seconds. Pushing the button again during this 5 sec- ond period stops SCAN tuning and remains tuned to that station.

Only stations in the selected band are set, and the station seek begins from the last frequency stored in memory button six. If AM, FM, SCAN, TUNE, SEEK, AUTO or a memory button is pushed while auto set is operating, auto set is canceled and AUTO OFF shows in the display window. AUTO LOAD Press the AUTO button for longer than 5
seconds while listening to the radio to acti- vate the auto load feature. When AUTO is depressed for longer than 5 seconds, the display window momentarily indicates AUTO LOAD, and the radio seeks the first six strong stations for every band. The first six strong stations are then stored in order in memory buttons one through six for each band (AM, FM1, and FM2). SEEK tuning Push the SEEK next broadcast station. Pushing the SEEKS up and button SEEKS down. Pushing the button again continues the SEEK function. Once the highest broadcast station is reached, the radio continues in the SEEK mode at the lowest station. Once the lowest broadcast station is reached, the radio con- 4-22 Heater, air conditioner and audio systems