2000 Nissan Quest Owners Manual

Download PDF Manual
5. Check under the vehicle again for leaking fuel. If you see or smell fuel, do not start your vehicle again. If no fuel is detected, try to start your vehicle again. WARNING If you see or smell fuel, do not reset the switch or try to start your vehicle. You could injure yourself or others. Have all the passengers get out of the vehicle and call the local fire department or a towing service. TOWING YOUR VEHICLE When towing your vehicle, U.S. States, Ca- nadian Provinces and local regulations for towing must be followed. Incorrect towing equipment could damage your vehicle. Towing instructions are available from an authorized NISSAN dealer. Local service operators are generally familiar with the applicable laws and procedures for towing. To assure proper towing and to prevent accidental damage to your vehicle, NISSAN recommends that you have a service opera- tor tow your vehicle. It is advisable to have the service operator carefully read the fol- lowing precautions. WARNING c Never ride in a vehicle that is being towed. c Never get under your vehicle after it has been lifted by a tow truck. 6-12 In case of emergency CAUTION c When towing, make sure that the transmission, axles, steering system and powertrain are in working con- dition. If any unit is damaged, dollies must be used. c Never use a tow bar that attaches to the bumper when you tow your ve- hicle. It may damage the bumper and cause damage to the transmission. c When towing with the front wheels on dollies: Turn the ignition key to the OFF position and secure the steering wheel in a straight-ahead position with a rope or similar device. Never place the ignition key in the LOCK position. This will result in damage to the steering lock mechanism. Move the gearshift lever to the N (Neutral) position. c When towing front wheel drive, auto- matic transmission models with the rear wheels on the ground (if you do not use towing dollies), release the parking brake. c Always attach safety chains before towing. Z X TOWING RECOMMENDED BY NISSAN NISSAN recommends that your vehicle be towed with the driving (front) wheels off the ground as illustrated. c Speed: Below 60 MPH (97 km/h) c Distance: Less than 500 miles (800 km) ACE1029 In case of emergency 6-13 Z X do not touch any part of the suspension, steering, brake or cooling systems. c Always pull the cable straight out from the front or rear of the vehicle. Never pull the vehicle at an angle. c Pulling devices such as ropes or canvas straps are not recommended for use in vehicle towing or recovery. c Stand clear of a stuck vehicle. WARNING Do not spin your tires at high speed. This could cause them to explode and result in serious injury. Parts of your vehicle could also overheat and be damaged. CAUTION c Never tow the vehicle with the front wheels on the ground, as this may cause serious and expensive dam- age to the transmission. If it is nec- essary to tow the vehicle with the rear wheels raised, always use tow- ing dollies under the front wheels. c Never tow automatic transmission models with all four wheels on the ground. This may cause serious and expensive damage to the transmis- sion. c Do not tow with a sling type truck, either from the front or the rear. It may cause body damage. c Never utilize the rear tie down brack- ets or slots to tow another vehicle as this may cause body damage. VEHICLE RECOVERY (Freeing a stuck vehicle) c Tow chains or cables must only be at- tached to the main structual members of the vehicle. c Pulling devices should be routed so they 6-14 In case of emergency Z X 7 Appearance and care Cleaning exterior ....................................................7-2 Washing .................................................................7-2 Waxing....................................................................7-2 Removing spots......................................................7-3 Underbody..............................................................7-3 Glass ......................................................................7-3 Aluminum alloy wheels...........................................7-3 Chrome parts..........................................................7-3 Cleaning interior .....................................................7-4 Floor mats ..............................................................7-4 Seat belts ...............................................................7-4 Corrosion protection...............................................7-5 Most common factors contributing to vehicle corrosion.................................................................7-5 Environmental factors influence the rate of corrosion.................................................................7-5 To protect your vehicle from corrosion ..................7-5 Z X CLEANING EXTERIOR AI1002M In order to maintain the appearance of your vehicle, it is important to take proper care of it. In the following cases, please wash your vehicle as soon as possible to protect the paint surface: c after a rainfall to prevent possible dam- age from acid rain. c after driving on coastal roads. c when contaminants such as soot, bird droppings, tree sap, metal particles or bugs get on the paint surface. 7-2 Appearance and care c when dust or mud builds up on the surface. Whenever possible, store or park your ve- hicle inside a garage or in a covered area. When it is necessary to park outside, park in a shady area or protect the vehicle with a body cover. Be careful not to scratch the paint sur- face when putting on or removing a body cover. WASHING Wash dirt off with a wet sponge and plenty of water. Clean the vehicle thoroughly using a mild soap, a special vehicle soap or general purpose dishwashing liquid mixed with clean, lukewarm (never hot) water. CAUTION c Do not wash the vehicle with strong household soap, strong chemical detergents, gasoline or solvents. c Do not wash the vehicle in direct sunlight or while the vehicle body is hot, as the surface may become water-spotted. c Avoid using tight-napped or rough cloths such as washing mitts. Care must be taken when removing caked-on dirt or other foreign sub- stances so that the paint surface is not scratched or damaged. Rinse the vehicle thoroughly with plenty of clean water. Inside flanges, seams and folds on the doors, hatches and hood are particularly vulnerable to the effects of road salt. There- fore, these areas must be regularly cleaned. Take care that the drain holes in the lower edge of the door are open. Spray water under the body and in the wheel wells to loosen the dirt and wash away road salt. A damp chamois can be used to dry the vehicle to avoid water spots. WAXING Regular waxing protects the paint surface and helps retain new vehicle appearance. After waxing, polishing is recommended to remove built-up residue and to avoid a ‘‘weathered’’ appearance. An authorized NISSAN dealer can assist Z X you in choosing the proper product. c Wax your vehicle only after a thorough washing. Follow the instructions supplied with the wax. c Do not use a wax containing any abra- sives, cutting compounds or cleaners that may damage the vehicle finish. c If the surface does not polish easily, use a ‘‘road tar’’ remover and wax again. Machine compounding or aggressive pol- ishing on a base coat/clear coat paint finish may dull the finish or leave swirl marks. REMOVING SPOTS Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning prod- ucts are available at an authorized NISSAN dealer or any automotive accessory store. UNDERBODY In areas where road salt is used in winter, the underbody must be cleaned regularly. This prevents dirt and salt from building up and causing underbody and suspension corrosion. Before the winter period and again in the spring, the underseal must be checked and, if necessary, re-treated. GLASS Use glass cleaner to remove smoke and dust film from the glass surfaces. It is nor- mal for glass to become coated with a film after the vehicle is parked in the hot sun. Glass cleaner and a soft cloth easily remove this film. CAUTION When cleaning the inside of the win- dows, do not use sharp-edged tools, abrasive cleaners or chlorine-based disinfectant cleaners. They could dam- age the electrical conductors, radio an- tenna, or rear window defogger ele- ments. ALUMINUM ALLOY WHEELS Wash regularly, especially during winter months in areas where road salt is used. Salt could discolor the wheel if not removed. CHROME PARTS Clean all chrome parts regularly with a non-abrasive chrome polish to maintain the finish. Appearance and care 7-3 Z X CLEANING INTERIOR Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft brush. Wipe the vinyl and leather surfaces with a clean, soft cloth dampened in mild soap solution, then wipe clean with a dry, soft cloth. Before using any fabric protector, read the manu- facturer’s recommendations. Some fabric protectors contain chemicals that may stain or bleach the seat material. Use a cloth dampened only with water, to clean the meter and gauge lens. CAUTION c Never use benzine, thinner, or any similar material. c Leather seats should be regularly coated with a leather wax like saddle soap. Never use car wax. c Never use fabric protectors unless recommended by the manufacturer. c Do not use glass or plastic cleaner on meter or gauge lens covers. It may damage the lens cover. 7-4 Appearance and care floor mat positioning aid FLOOR MATS The use of genuine NISSAN floor mats can extend the life of your vehicle carpet and make it easier to clean the interior. No matter what mats are used, be sure they are fitted for your vehicle and are prop- erly positioned in the footwell to prevent interference with pedal operation. Mats should be maintained with regular cleaning and replaced if they become excessively worn. Front (Driver side only) floor mat This model bracket to act as a floor mat positioning aid. NISSAN floor mats, specially designed for your vehicle, incorporate grommets. To in- stall, simply position the mat using the floor mat bracket hook through the floor mat grommet hole while centering the mat in the footwell. Periodically check to make certain the mat is properly positioned. SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild includes a front soap solution. Allow the belts to dry com- pletely before using them. WARNING Do not allow wet seat belts to roll up in the retractor. NEVER use bleach, dye, or chemical solvents to clean the seat belts, since these may severely weaken the seat belt webbing. Z X CORROSION PROTECTION MOST COMMON FACTORS CONTRIBUTING TO VEHICLE CORROSION 1. The accumulation of moisture-retaining dirt and debris in body panel sections, cavities, and other areas. 2. Damage to paint and other protective coatings caused by gravel and stone chips or minor traffic accidents. ENVIRONMENTAL FACTORS IN- FLUENCE THE RATE OF COR- ROSION Moisture Accumulation of sand, dirt and water on the vehicle body underside can accelerate cor- rosion. Wet floor coverings do not dry com- pletely inside the vehicle, and should be removed for drying to avoid floor panel corrosion. Relative humidity Corrosion will be accelerated: c in areas of high relative humidity. c in areas where the temperatures stay above freezing. c where atmospheric pollution exists. c where road salt is used. Temperature A temperature increase accelerates the rate of corrosion to those parts which are not well ventilated. Air pollution Industrial pollution, the presence of salt in the air in coastal areas, or heavy road salt use accelerates the corrosion process. Road salt also accelerates the disintegra- tion of paint surfaces. TO PROTECT YOUR VEHICLE FROM CORROSION c wash and wax your vehicle often to keep the vehicle clean. c always check for minor damage to the paint and repair it as soon as possible. c keep drain holes at the bottom of the doors open to avoid water accumulation. c check the underbody for accumulation of sand, dirt or salt. If present, wash with water as soon as possible. CAUTION c NEVER remove dirt, sand or other debris from the passenger compart- ment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom. c Never allow water or other liquids to come in contact with electronic com- ponents inside the vehicle as this may damage them. Appearance and care 7-5 Z X MEMO 7-6 Appearance and care Z X 8 Do-it-yourself Maintenance precautions .......................................8-2 Engine compartment check locations ....................8-3 Engine cooling system ...........................................8-4 Checking engine coolant level ...............................8-4 Changing engine coolant .......................................8-5 Engine oil ...............................................................8-5 Checking engine oil level .......................................8-5 Changing engine oil ...............................................8-6 Changing engine oil filter .......................................8-7 Automatic transmission fluid ..................................8-8 Temperature conditions for checking.....................8-8 Power steering fluid................................................8-9 Brake fluid ..............................................................8-9 Window washer fluid ............................................8-10 Battery ..................................................................8-10 Jump starting........................................................8-11 Drive belts ............................................................8-12 Spark plugs ..........................................................8-12 Replacing spark plugs..........................................8-12 Air cleaner ............................................................8-13 Cabin air filter.......................................................8-14 Windshield wiper blades ......................................8-17 Cleaning ...............................................................8-17 Replacing .............................................................8-17 Parking brake and brake pedal............................8-19 ..........................................8-19 Checking parking brake .......................................8-19 Checking brake pedal ..........................................8-19 Brake booster.......................................................8-20 Fuses....................................................................8-20 Engine compartment ............................................8-20 Passenger compartment ......................................8-21 Multi-remote controller battery replacement ........8-22 Lights....................................................................8-23 Headlights ............................................................8-23 Exterior and interior lights ....................................8-24 Wheels and tires ..................................................8-28 Tire pressure ........................................................8-28 Types of tires........................................................8-29 Tire chains............................................................8-30 Changing tires and wheels...................................8-30 Z X MAINTENANCE PRECAUTIONS When performing any inspection or mainte- nance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precautions which should be closely observed. WARNING c Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the ve- hicle from moving. Move the gear- shift lever to P (park). c Be sure the ignition key is in the OFF or Lock position when performing any parts replacement or repairs. c Your vehicle is equipped with an automatic engine cooling fan. It may come on at any time without warn- ing, even if the ignition key is in the OFF position and the engine is not running. To avoid injury, always dis- connect the negative battery cable before working near the fan. c If you must work with the engine run- ning, keep your hands, clothing, hair and tools away from moving fans, belts and any other moving parts. 8-2 Do-it-yourself c It is advisable to secure or remove any loose clothing and remove any jewelry, such as rings, watches, etc. before working on your vehicle. c Always wear eye protection when- ever you work on your vehicle. c If you must run the engine in an enclosed space such as a garage, be sure there is proper ventilation for exhaust gases to escape. c Never get under the vehicle while it is supported only by a jack. If it is necessary to work under the vehicle, support it with safety stands. c Keep smoking materials, flame and sparks away from the fuel tank and battery. c On gasoline engine models with the multiport fuel injection (MFI) system, the fuel filter or fuel lines should be serviced by an authorized NISSAN dealer because the fuel lines are under high pressure even when the engine is off. CAUTION c Do not work under the hood while the engine is hot. Turn off the engine and wait until it cools down. c Never connect or disconnect the bat- tery or any transistorized compo- nent while the ignition switch is in the ON position. c Avoid contact with used engine oil. Improperly disposed motor oil and/ or other vehicle fluids can damage the environment. Always conform to local regulations for disposal of ve- hicle fluid. This ‘‘Do-it-yourself’’ section gives instruc- tions regarding only those items which are relatively easy for an owner to perform. You should be aware that incomplete or improper servicing may result in operating difficulties or excessive emissions, and could affect your warranty coverage. If in doubt about any servicing, have it done by an authorized NISSAN dealer. Z X ENGINE COMPARTMENT CHECK LOCATIONS ADI1082 Do-it-yourself 8-3 Z X ENGINE COOLING SYSTEM The engine cooling system is filled at the factory with a high-quality, year-round, anti- freeze coolant solution. The anti-freeze so- lution contains rust and corrosion inhibitors, therefore additional engine cooling system additives are not necessary. CAUTION When adding or replacing coolant, be sure to use only an ethylene glycol anti-freeze with the proper mixture ratio of 50% Genuine Nissan anti-freeze coolant or equivalent and 50% dem- ineralized or distilled water. The use of other types of coolant solutions may damage the engine cooling system. Outside tempera- ture down to °C −35 °F −30 Genuine NISSAN Anti-freeze Coolant or equivalent Demineral- ized or Dis- tilled water 50% 50% 8-4 Do-it-yourself WARNING c Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator. c The radiator is equipped with a pres- sure cap. To prevent engine damage, use only a genuine NISSAN radiator cap. ADI1083 CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir tank when the engine is cold. If the coolant level is below MIN, add coolant up to the MAX level. If the reservoir tank is empty, check the coolant level in the radiator when the engine is cold. If there is insufficient cool- ant the radiator with coolant up to the filler opening and also add it to the reservoir tank up to the MAX level. in the radiator, fill Z X ENGINE OIL If the cooling system frequently requires coolant, have it checked by an autho- rized NISSAN dealer. CHANGING ENGINE COOLANT An authorized NISSAN dealer can change the engine coolant. The service procedure is found in NISSAN’s service manual. Improper servicing can result in reduced heater engine overheating. performance and WARNING c To avoid danger of being scalded, never change the coolant when the engine is hot. c Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator. ADI1084 ADI0009 CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and apply the parking brake. 2. Start the engine and let it idle until reaches operating temperature. it 3. Turn the engine off. Wait a few minutes for the oil to drain back into the oil pan. 4. Remove the dipstick and wipe it clean. Reinsert it all the way. level. 5. Remove the dipstick again and check the oil It should be between the H (High) and L (Low) marks. If the oil level is below the L (Low) mark, remove the oil filler cap and pour recommended oil through the opening. Do not overfill. 6. Recheck the oil level with the dipstick. It is normal to add some oil between oil maintenance intervals or during the break-in period, depending on the sever- ity of operating conditions. Do-it-yourself 8-5 Z X CAUTION Oil level should be checked regularly. Operating with an insufficient amount of oil can damage the engine, and such damage is not covered by warranty. ADI0057 CHANGING ENGINE OIL 1. Park the vehicle on a level surface and apply the parking brake. 2. Start the engine and let it idle until it reaches operating temperature, then turn it off. 3. Remove the oil filler cap. 4. Place a large drain pan under the drain plug. 5. Remove the drain plug with a wrench and completely drain the oil. 8-6 Do-it-yourself If the oil filter is to be changed, remove and replace it at this time. See ‘‘Chang- ing engine oil filter’’ later in this section. WARNING c Be careful not to burn yourself. The engine oil may be hot. c Prolonged and repeated contact with used engine oil may cause skin can- cer. c Try to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible. c Keep used engine oil out of reach of children. Waste oil must be disposed of properly. Check your local regulations. 6. Clean and reinstall the drain plug and a new washer. Securely tighten the drain plug with a wrench. Z X Drain plug tightening torque: 22 to 29 ft-lb (29 to 39 Nzm) Do not use excessive force. 7. Refill the engine with a recommended oil through the oil filler opening then install the oil filler cap securely. See the ‘‘Technical and consumer infor- mation’’ section for drain and refill capac- ity. The drain and refill capacity depends on the oil temperature and drain time. Use these specifications for reference only. Always use the dipstick to determine when the proper amount of oil is in the engine. 8. Start the engine. Check for leakage around the drain plug. Correct as re- quired. 9. Turn the engine off and wait several level with the minutes. Check the oil dipstick. Add engine oil if necessary. ADI0010 CHANGING ENGINE OIL FILTER 1. Park the vehicle on a level surface and apply the parking brake. 2. Turn the engine off. 3. Place a large drain pan under the oil filter. 4. Loosen the oil filter wrench. Then, remove the oil filter by turning it by hand. filter with an oil CAUTION Be careful not to burn yourself. The engine oil may be hot. 5. Wipe the engine oil filter mounting sur- face with a clean rag. Be sure to remove any old gasket material remaining on the mounting surface of the engine. 6. Coat the rubber gasket on the new filter with clean engine oil. 7. Screw on the oil filter in until a slight resistance is felt, then tighten an addi- tional 2/3 turn. 8. Start the engine and check for leakage around the oil filter. Correct as required. 9. Turn the engine off and wait several minutes. Check the oil level. Add engine oil if necessary. Do-it-yourself 8-7 Z X AUTOMATIC TRANSMISSION FLUID ADI1085 WARNING c When the engine is running, keep hands, jewelry and clothing away from any moving parts such as the cooling fan and drive belts. c Automatic transmission fluid is poi- sonous and should be stored care- fully in marked containers out of the reach of children. 8-8 Do-it-yourself TEMPERATURE CONDITIONS FOR CHECKING c Check the fluid level using the HOT range on the dipstick after the following conditions have been met: — The engine is warmed up to operating temperature. — The vehicle is driven at least 15 minutes. — The automatic transmission fluid is warmed to between 150°F and 170°F (66°C and 77°C). c The fluid can be checked at fluid tem- peratures of 70°F to 95°F (21°C to 35°C) using the COLD range on the dipstick after the engine is warmed up and before driving. However, the fluid should be re-checked using the HOT range. 1. Park the vehicle on a level surface and set the parking brake. 2. Start the engine, then move the shift selector lever through the range of gears, ending in P (Park). WDI0004 3. Check the fluid level with the engine idling. 4. Remove the dipstick and wipe it clean with a lint-free cloth. 5. Reinsert the dipstick into the dipstick tube as far as it goes. 6. Remove the dipstick and note the read- ing. If the level is at the low side of either range, add fluid through the dipstick tube. Z X CAUTION DO NOT OVERFILL. Use ONLY Nissan Matic ‘D’ (Continental U.S. and Alaska) or Canada NISSAN Automatic Trans- mission Fluid. DexronTM III/MerconTM or equivalent may also be used. Out- side the continental United States and Alaska contact a Nissan dealership for more information regarding suitable fluids, recommended brand(s) of DexronTM III/MerconTM. including NOTE: If the vehicle has been driven for a long time at high speeds, or in city traffic in hot weather, or if it is being used to pull a trailer, the accurate fluid level cannot be read. You should wait until the fluid has cooled down (about 30 minutes). POWER STEERING FLUID BRAKE FLUID ADI1086 ADI1087 Check the fluid level in the reservoir. The fluid level should be checked by looking at the MAX and MIN lines at fluid tempera- tures of 32°F to 86°F (0°C to 30°C). If the fluid is below the MIN line, add auto- matic transmission fluid type F up to the MAX line. CAUTION c DO NOT OVERFILL. c The recommended fluid is type F automatic transmission fluid or equivalent. Check the fluid level in the reservoir. If the fluid is below the MIN line or the brake warning light comes on, add DOT 3 fluid up to the MAX line. fluid must be added frequently, the system should be thoroughly checked by an authorized NISSAN dealer. For further brake fluid specification informa- tion, refer to the ‘‘Technical and Consumer Information’’ section in this manual. If Do-it-yourself 8-9 Z X WINDOW WASHER FLUID BATTERY WARNING Use only new fluid from a sealed con- tainer. Old, inferior, or contaminated fluid may damage the brake system. The use of improper fluids can damage the brake system and affect the vehi- cle’s stopping ability. CAUTION Do not spill the fluid on painted sur- faces. This will damage the paint. If fluid is spilled, wash with water. 8-10 Do-it-yourself ADI1088 To check the fluid level, look down the fill tube of the washer fluid reservoir in the engine compartment. Add fluid when the low washer fluid warning light (Canada only) comes on. To add fluid, remove the reservoir cap and refill the reservoir. This reservoir serves both the front and rear washer systems. CAUTION Do not substitute engine anti-freeze coolant for window washer solution. This may result in damage to the paint. c Keep the battery surface clean and dry. Any corrosion should be washed off with a solution of baking soda and water. c Make certain the terminal connections are clean and securely tightened. c If the vehicle is not to be used for 30 days or longer, disconnect the negative (−) battery terminal cable to prevent dis- charging. WARNING c Do not expose the battery to flames or electrical sparks. Hydrogen gas generated by the battery is explo- sive. Do not allow battery fluid to contact your skin, eyes, fabrics, or painted surfaces. After touching a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 min- utes and seek medical attention c When working on or near the battery, always wear suitable eye protection and remove all jewelry. Z X c Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after han- dling. c Keep the battery out of the reach of children. JUMP STARTING If jump starting is necessary, see the ‘‘In case of emergency’’ section. If the engine does not start by jump starting, the battery may have to be replaced. Contact an autho- rized NISSAN dealer. WDI0022 it Check the fluid level in each cell. It should be between the MAX and MIN lines. If is necessary to add fluid, add only distilled water to bring the level to the indi- cator in each filler opening. Do not overfill. 1. Remove the cell plugs using a suitable tool. 2. Add distilled water up to the MAX level. 3. Tighten cell plugs. Do-it-yourself 8-11 Z X DRIVE BELTS SPARK PLUGS 2. Have the belts checked regularly for con- dition and tension in accordance with the maintenance schedule found in the ‘‘Maintenance’’ section of this manual. ADI0060 WARNING Be sure the ignition key is in the OFF or LOCK position. The engine could rotate unexpectedly. 1. Visually inspect each belt for signs of unusual wear, cuts, fraying or looseness. If the belt is loose or in poor condition, have it replaced or adjusted by an autho- rized NISSAN dealer. 8-12 Do-it-yourself ADI0061 REPLACING SPARK PLUGS WARNING Be sure the engine and ignition switch are off and that the parking brake is engaged securely. CAUTION Be sure to use the correct socket to remove the spark plugs. An incorrect socket can damage the spark plugs. Z X 2. Remove the spark plugs with a spark plug socket. The plug socket has a rub- ber seal that holds the spark plug so it does not fall when it is pulled out. Make sure each spark plug is snugly fitted into the plug socket. 3. Fit the new plugs, one at a time, into the spark plug socket and install them. Use only the specified spark plugs. Turn each plug several full turns by hand, then tighten with the spark plug socket to the correct torque. Do not overtighten. Spark plug tightening torque: 14 to 22 ft-lb (20 to 29 Nzm) 4. Holding the boot, re-connect each high tension cable to its proper spark plug by pushing it on until you feel a snap. ADI1100 Platinum-tipped spark plugs It is not necessary to replace platinum- tipped spark plugs as frequently as conven- tional type spark plugs because they last much longer. Follow the maintenance schedule, but do not reuse the spark plugs by cleaning or regapping. c Always replace spark plugs with rec- ommended or equivalent ones. 1. Disconnect the spark plug cables from the spark plugs. When disconnecting, always hold the boots, not the cables. AIR CLEANER ADI0579 The filter should not be cleaned and reused. Replace it according to the maintenance intervals shown in the ‘‘Maintenance’’ sec- tion of this manual. When replacing the filter, unclip the four clamps and remove the filter. Wipe the inside of the air cleaner housing and the cover with a damp cloth when replacing filter. Do-it-yourself 8-13 Z X WARNING c Operating the engine with the air cleaner removed can cause you or others to be burned. The air cleaner not only cleans the air, it stops flame if the engine backfires. If it isn’t there and the engine backfires, you could be burned. Do not drive with the air cleaner removed, and be careful when working on the engine with the air cleaner removed. c Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed. Doing so could result in serious injury. CABIN AIR FILTER The cabin air filter restricts the entry of airborne dust and pollen particles and re- duces some objectionable outside odors. The filter is located just the windshield under the cowl cover on the passenger side of the vehicle. To replace the filter, perform the following procedure. in front of 8-14 Do-it-yourself ADI1103 ADI1104 1. Remove the windshield wiper arms. c Lift the wiper arm away from the wind- shield surface until the wiper is perpen- dicular to the windshield. c Lift and remove the wiper arm, while holding the small retaining clip at the base of wiper arm outward. 2. Remove the cowl cover. c Remove the six screws. c Open the hood. Z X ADI1105 ADI1106 ADI1107 c Remove the four plastic screws from the forward edge of the cowl cover. c Remove the four plastic screw anchors. c Disconnect the windshield washer hose at the passenger side rear corner of the engine compartment. c Push the windshield washer hose and the grommet through the sheet metal hole. c Lift the cowl cover and remove it from the vehicle. 3. Locate the cabin air filter on the passen- ger side of the vehicle. c Remove the four screws from the cabin air filter cover. c Remove the cabin air filter cover. Do-it-yourself 8-15 Z X ADI1108 c Remove the cabin air filter element by pulling forward on the top surface of the filter and lifting. 8-16 Do-it-yourself 8. Position the cowl cover in place. 9. Reinstall the four screw anchors and the four screws. 10. Close the hood. 11. Install the six screws in the cowl cover. 12. Install the windshield wiper arms. c Push the wiper arm downward onto the wiper arm pivot until the small retaining clip snaps into the locked position. ADI1109 c Lower the wiper arm blade onto the windshield surface. 4. 5. Install the new cabin air filter element into the filter retaining frame, ensure that you insert the three retaining tabs in the bottom of the filter frame. Install the filter top cover and the four screws. 6. Feed the windshield washer hose from the cowl cover through the hole in the sheet metal. c Ensure that you fully seat the rubber grommet into the sheet metal hole. 7. Reconnect the windshield washer hose. Z X WINDSHIELD WIPER BLADES CLEANING If your windshield is not clear after using the windshield washer or if the wiper blade chatters when running, wax or other mate- rial may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water. Clean the blade by wiping it with a cloth soaked in a washer solution or a mild deter- gent. Then, rinse the blade with clear water. If your windshield is still not clear after cleaning the blades and using the wipers, replace the blades. REPLACING 1. Lift the wiper arm away from the wind- shield. 2. Push the tab, then move the wiper blade down the wiper arm to remove. 3. Remove the wiper blade. 4. Insert the new wiper blade onto the wiper arm until it clicks into place. ADI1022 CAUTION c After wiper blade replacement, re- turn the wiper arm to its original position; otherwise it may be dam- aged when the engine hood is opened. c Make sure the wiper blades contact the glass; otherwise the arms may be damaged from wind pressure. Do-it-yourself 8-17 Z X Rear window wiper blade 1. Lift the wiper arm away from the wind- shield. 2. Push the tab, then move the wiper blade down the wiper arm to remove. 3. Insert a new wiper blade onto the wiper arm and press down until the blade clicks into place. 8-18 Do-it-yourself ADI1114 Z X PARKING BRAKE AND BRAKE PEDAL CHECKING BRAKE PEDAL ADI1089 ADI0027 CHECKING PARKING BRAKE From the released position, push the park- ing brake foot lever down. If the number of clicks is out of the range listed above, see an authorized NISSAN dealer. With the engine running, check the distance between the upper surface of the pedal and the floor. If it is out of the range shown above, see an authorized NISSAN dealer. Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes. The front disc-type brakes self-adjust every time the brake pedal is applied. The rear drum-type brakes also self-adjust every time the brake pedal is applied. If the brake pedal goes down farther than normal, see an authorized NISSAN dealer. WARNING See an authorized NISSAN dealer for a brake system check if the brake pedal height does not return to normal. Brake pad wear indicators The disc pads on your vehicle have audible wear indicators. When a brake pad requires replacement, it makes a high pitched scrap- ing or screeching sound when the vehicle is in motion whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the wear indicator sound is heard. Under some driving or climate conditions, occasional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is nor- mal and does not affect the function or performance of the brake system. The rear drum brakes do not have audible wear indicators. If you ever hear an unusu- ally loud noise from the rear drum brakes, have them inspected as soon as possible by an authorized NISSAN dealer. Do-it-yourself 8-19 Z X Proper brake inspection intervals should be followed. For more information regard- ing brake inspections, see the appropriate maintenance schedule information in the ‘‘Maintenance’’ section of this manual. BRAKE BOOSTER Check the brake booster function as fol- lows: 1. With the engine off, press and release times. When the brake pedal several brake pedal movement (distance of travel) remains the same from one pedal application to the next, continue on to the next step. 2. While depressing the brake pedal, start the engine. The pedal height should drop a little. 3. With the brake pedal depressed, turn the engine off. Keep the pedal depressed for about 30 seconds; the pedal height should not change. 4. Run the engine for one minute without depressing the brake pedal, then turn it off. Depress the brake pedal several times. The pedal travel distance will de- crease gradually with each depression 8-20 Do-it-yourself FUSES as the vacuum is released from the booster. If the brakes do not operate properly, see an authorized NISSAN dealer. ADI1090 ENGINE COMPARTMENT CAUTION Never use a fuse of a higher amperage rating than that specified on the fuse box cover. This could damage the elec- trical system or cause a fire. If a headlight does not come on, check for an open fuse: The left headlight (driver’s side) and right headlight (passenger side) fuses are lo- Z X cated in the left-hand fuse box, near the radiator cap. 1. Turn the headlight switch to the OFF position. 2. Open the engine hood. 3. Remove the fuse box cover. 4. Remove the fuse with the fuse puller attached to the passenger compartment fuse box cover. 5. If the fuse is open, replace it with a new fuse. 6. If a new fuse opens again, have the electrical system checked and repaired by an authorized NISSAN dealer. Fusible Links If the electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace only with genuine NISSAN parts. If the new fusible link melts again, have the system checked and repaired by an autho- rized NISSAN dealer. PASSENGER COMPARTMENT CAUTION Never use a fuse of a higher amperage rating than that specified on the fuse box cover. This could damage the elec- trical system or cause a fire. If the electrical equipment does not operate, check for an open fuse: 1. Remove the key from the ignition. WDI0023 2. Open the fuse box cover. Refer to the fuse label on the fuse box cover to locate the fuse in question. 3. Remove the fuse with the fuse puller. 4. If the fuse is open, replace it with a new fuse. 5. If a new fuse opens again, have the electrical system checked and repaired by an authorized NISSAN dealer. Do-it-yourself 8-21 Z X MULTI-REMOTE CONTROLLER BATTERY REPLACEMENT Replace the battery as follows: 1. Open the lid using a coin. 2. Replace the battery with a new one. Insert the batteries as illustrated above. Recommended battery: Panasonic CR2025, 3V or equivalent. 8-22 Do-it-yourself APD1087 3. Close the lid securely. 4. Press the button, then the button two or three times to check the multi- remote controller operation. If the batteries are removed for any reason other than replacement, perform step 4. c An improperly disposed battery can hurt the environment. Always conform to local regulations for battery disposal. c The multi-remote controller is water- resistant; however, if it does get wet, immediately wipe completely dry. c The operational range of the multi- remote controller extends to approxi- mately 30 ft (10 m) from the vehicle. This range may vary with conditions. FCC Notice: Changes or modifications not expressly approved by the manufacturer for com- pliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference re- ceived, including interference that may cause undesired operation of the device. Z X LIGHTS AEL076-A HEADLIGHTS The headlight is a semi-sealed beam type which uses a replaceable headlight (halo- gen) bulb. A bulb can be replaced from inside the engine compartment without re- moving the headlight assembly. CAUTION c High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped. CAUTION DO NOT TOUCH THE BULB. c Use the same number and wattage as originally installed: Wattage 65/55 Bulb no. 9007 (HB5) c Aiming is not necessary after replac- ing the bulb. When aiming adjust- ment is necessary, contact an authorized NISSAN dealer. c Do not leave the bulb out of the headlight reflector for a long period of time as dust, moisture and smoke may enter the headlight body and affect the performance of the head- light. c When handling the bulb, do not touch the glass envelope. Removing the headlight bulb 1. Disconnect the negative (-) battery cable. 2. Disconnect the electrical connector from the rear end of the bulb. 3. Turn the bulb retaining ring counterclock- it is free from the headlight wise until reflector, then remove it. 4. Remove the headlight bulb by pulling it straight out. Do not shake or rotate the bulb when removing it. Replacing the headlight bulb 1. Insert the bulb into the headlight reflector with the flat side of the plastic base facing upward. 2. Install the bulb retaining ring and turn it clockwise until it stops. 3. Push the electrical connector into the bulb plastic base until it snaps and stops. Do-it-yourself 8-23 Z X EXTERIOR AND INTERIOR LIGHTS Item Wattage (W) Bulb No. Headlight assembly High/Low Front turn signal light Front combination light: Front side marker light Parking/Cornering Rear combination light: Turn signal Stop/Tail Rear side marker light Back-up light License plate light High-mounted stop light Interior lights Personal reading light Luggage compartment light Steplight Spotlight 8-24 Do-it-yourself 65/55 8.25/27 3.8 8.25/27 27 8.25/27 27 3.8 12.8 12 10 12 3.8 10 9007 (HB5) 3157NA 194 3157K 3156K 3157K 168 3156K 194 912 211-2 578 211-2 194 578 Z X ADI1093 Replacement procedures All lights (except for headlights) are either type A, B, C or D. When replacing a bulb, first remove the lens and/or cover. Do-it-yourself 8-25 WDI0012 Z X 8-26 Do-it-yourself ADI1122 Z X ADI1096 Do-it-yourself 8-27 Z X WHEELS AND TIRES DI1033M TIRE PRESSURE If you have a flat tire, see the ‘‘In case of emergency’’ section of this manual. Maximum inflation pressure Do not exceed the maximum inflation pres- sure shown on the side wall of the tire. Tire inflation pressure Periodically check the tire pressure (includ- ing the spare). Incorrect tire pressure may adversely affect tire life and vehicle han- dling. Tire pressure should be checked when tires are COLD. Tires are considered ADI1095 Z X 8-28 Do-it-yourself COLD after the vehicle has been parked for three or more hours, or driven less than 1 mile (1.6 km). COLD tire pressures are shown on the tire placard affixed to the glove box door. WARNING c Improperly inflated tires can fail sud- denly and cause an accident. c The vehicle capacity weight is indi- cated on the tire placard. Do not load your vehicle beyond this capacity. Overloading your vehicle may result in reduced tire life, unsafe operating conditions due to premature tire fail- ure, or unfavorable handling charac- teristics and could also lead to a serious accident. Loading beyond the specified capacity may also re- sult in failure of other vehicle com- ponents. c Before taking a long trip, or whenever you have loaded your vehicle heavily, use a tire pressure gauge to ensure that the specified level. the tire pressures are at c Do not drive your vehicle over 85 MPH (140 km/h) unless it is equipped with high speed rated tires. Driving faster than 85 MPH (140 km/h) may result in tire failure, loss of control and possible injury. TYPES OF TIRES WARNING When changing or replacing tires, be sure all four tires are of the same type (i.e., summer, all season or snow) and construction. An authorized NISSAN dealer may be able to help you with information about tire type, size, speed rating and availability. Replacement tires may have a lower speed rating than the factory equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maxi- mum speed rating of the tire. All season tires NISSAN specifies All Season tires to pro- vide good performance all year, including snowy and icy road conditions. All Season Tires are identified by ‘‘ALL SEASON’’ and/or ‘‘M&S’’ on the tire sidewall. Snow tires have better snow traction than All Season tires and may be more appropriate in some areas. Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. If you do not, it can adversely affect the safety and han- dling of your vehicle. Generally, snow tires have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire. If you operate your vehicle in snowy or icy conditions, NISSAN recommends the use of snow or all season tires on all four wheels. For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. Do-it-yourself 8-29 Z X TIRE CHAINS Use of tire chains may be prohibited accord- ing to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are of proper size for the tires on your vehicle and are installed according to the chain manufacturer’s sug- gestions. Use only SAE Class ‘‘S’’ chains. Other types may damage your vehicle. Use chain tensioners when recommended by the tire chain manufacturer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the possibil- ity of whipping action damage to the fenders or undercarriage. If possible, avoid fully loading your vehicle when using tire chains. In addition, drive at a reduced speed. Do not exceed maximum speed suggested by the chain manufacturer. Otherwise, your ve- hicle may be damaged and/or vehicle han- dling and performance may be adversely affected. Never install tire chains on TEMPORARY USE ONLY spare tires. Do not use tire chains on dry roads. Tire chains must be installed only on the front wheels and not on the rear wheels. 8-30 Do-it-yourself WARNING c After rotating the tires, check and adjust the tire pressure. c Retighten the wheel nuts when the vehicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.). c Do not include the spare tire in the tire rotation. ADI0656 CHANGING TIRES AND WHEELS Tire rotation Tires should be rotated every 7,500 miles (12,000 km). Tighten wheel nuts to 72 to 87 ft-lb (98 to 118 Nzm). See ‘‘Flat tire’’ in the ‘‘In case of emergency’’ section for tire replacing procedures. Z X DI1035M Tire wear and damage WARNING c Tires should be periodically in- spected for wear, cracking, bulging, or objects caught in the tread. If excessive wear, cracks, bulging, or deep cuts are found, the tire(s) should be replaced. c The original tires have a built-in tread wear indicator. When the wear indicator is visible, the tire(s) should be replaced. c Improper service of the spare tire may result in serious personal in- jury. If it is necessary to repair the spare tire, contact an authorized NISSAN dealer. Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recom- mended types and sizes are shown in ‘‘Wheels and tires’’ in the ‘‘Technical and consumer information’’ section of this manual. WARNING c The use of tires other than those recommended, or the mixed use of tires of different brands, construction (bias, bias-belted or radial), or tread patterns can adversely affect the ride, braking, handling, ground clearance, body-to-tire clearance, snow chain clearance, speedometer calibration, headlight aim and bumper height. Some of these effects may lead to accidents and could result in serious personal injury. c If the wheels are changed for any reason, always replace with wheels which have the same off-set dimen- sion. Wheels of a different offset could cause pre-mature tire wear, de- grading vehicle handling characteris- tics and/or interference with the brake discs/drums. Such interference can lead to decreased braking effi- ciency early brake pad/ shoe wear. Refer to “Wheel/tire size” in the “Technical and consumer infor- mation” section of this manual for wheel off-set dimensions. and/or c Do not install a deformed wheel or tire even if it has been repaired. Such wheels or tires could have structural damage and could fail without warn- ing. c The use of retread tires is not recom- mended. Wheel balance Unbalanced wheels may affect vehicle han- dling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be balanced as required. Do-it-yourself 8-31 Z X Wheel balance service should be performed with the wheels off the vehicle. Spin balanc- ing the front wheels on the vehicle could lead to transmission damage. Care of wheels c Wash the wheels when washing the ve- hicle to maintain their appearance. c Clean the inner side of the wheels when the wheel is changed or the underside of the vehicle is washed. c Do not use abrasive cleaners when washing the wheels. c Inspect wheel rims regularly for dents or corrosion. Such damage may cause loss of pressure or poor seal at the tire bead. c NISSAN recommends waxing the road wheels to protect against road salt in areas where it is used during winter. Spare tire (TEMPORARY USE ONLY spare tire) US only. Canadian vehicles are equipped with a full size spare tire. Observe the following precautions if the TEMPORARY USE ONLY spare tire must be used, other- wise your vehicle could be damaged or involved in an accident. 8-32 Do-it-yourself WARNING c The spare tire should be used only for emergency use only. It should be replaced by the standard tire at the first opportunity to avoid possible tire or diffential damage. c Drive carefully while the TEMPO- RARY USE ONLY spare tire is in- stalled. Avoid sharp turns and abrupt braking while driving. c Periodically check spare tire infla- tion pressure. Always keep the pres- sure of the TEMPORARY USE ONLY spare tire at 60 psi (420 kP, 4.2 bar). Always keep the pressure of the full size spare tire (if so equipped) at the recommended pressure for standard tires, as indicated on the tire placard. For tire placard location, see ‘‘Tire placard’’ in the index of this manual. c With the TEMPORARY USE ONLY spare tire installed do not drive the vehicle at speeds faster than 50 mph (80 km/h). c When driving on roads covered with snow or ice, the TEMPORARY USE ONLY spare tire should be used on the rear wheel and the original tire used on the front wheels (drive wheels). Use tire chains only on the front (original) tires. c Tire tread of the when the TEMPO- RARY USE ONLY spare tire will wear at a faster rate than the standard tire. Replace the spare tire as soon as the tread wear indicators appear. c Do not use the spare tire on other vehicles. c Do not use more than one spare tire at the same time. c Do not tow a trailer when the TEM- PORARY USE ONLY spare tire is installed. Z X CAUTION c Do not use tire chains on the TEM- PORARY USE ONLY spare tire. Tire chains will not fit properly and may cause damage to the vehicle. c Because the TEMPORARY USE ONLY spare tire is smaller than the original tire, ground clearance is re- duced. To avoid damage to the ve- hicle, do not drive over obstacles. Also, do not drive the vehicle through an automatic car wash since it may get caught. Do-it-yourself 8-33 Z X MEMO 8-34 Do-it-yourself Z X 9 Maintenance Maintenance precautions .......................................9-2 General maintenance.............................................9-2 Explanation of maintenance items.........................9-2 Exterior maintenance .............................................9-2 Interior maintenance...............................................9-3 Periodic maintenance schedules ...........................9-5 Schedule One ........................................................9-5 Schedule Two ........................................................9-5 Explanation of maintenance items.......................9-10 Z X MAINTENANCE PRECAUTIONS Your new NISSAN has been designed to have minimum maintenance requirements with longer service intervals to save you both time and money. However, some day- to-day and regular maintenance is essential to maintain your NISSAN’s good mechani- cal condition, as well as its emission and engine performance. It is the owner’s responsibility to make sure the specified maintenance, as well as gen- eral maintenance, is performed. As the vehicle owner, you are the only one who can ensure that your vehicle receives proper maintenance. You are a vital link in the maintenance chain. General maintenance General maintenance includes those items which should be checked during normal day-to-day operation of the vehicle. They are essential if your vehicle is to continue to operate properly. It is your responsibility to perform these maintenance procedures regularly as prescribed. These checks or inspections can be done by yourself, a qualified technician or, if you prefer, an authorized NISSAN dealer. 9-2 Maintenance Periodic maintenance The maintenance items listed under ‘‘Peri- odic Maintenance’’ in this section must be serviced at regular intervals. However, under severe driving conditions, additional or more frequent maintenance is required. Where to go for service If maintenance service is required or your vehicle appears to malfunction, have the systems checked and tuned by an autho- rized NISSAN dealer. NISSAN technicians are well-trained spe- cialists who are kept up to date with the latest service information through technical bulletins, service tips, and in-dealership training programs. They are completely qualified to work on NISSAN vehicles be- fore they begin work on your vehicle, rather than after they have worked on it. You can be confident that an authorized NISSAN dealer’s service department per- forms the best job to meet the maintenance requirements on your vehicle — in a reliable and economic way. GENERAL MAINTENANCE During the normal day-to-day operation of the vehicle, general maintenance should be performed regularly as prescribed in this section. If you detect any unusual sounds, vibrations or smells, be sure to check for the cause or have an authorized NISSAN dealer do it promptly. In addition, you should notify an authorized NISSAN dealer if you think repairs are required. When performing any checks or mainte- nance work, closely observe the precau- tions in the ‘‘Do-it-yourself’’ section of this manual. EXPLANATION OF MAINTE- NANCE ITEMS Additional information on the following items with an ‘‘*’’ can be found in the ‘‘Do-it- yourself’’ section of this manual. EXTERIOR MAINTENANCE Outside the vehicle The maintenance items listed here should be performed from time to time, unless otherwise specified. Tires* — Check the pressure with a gauge periodically when at a service station, in- Z X cluding the spare, and adjust to the speci- fied pressure if necessary. Check carefully for damage, cuts or excessive wear. Wheel nuts* — When checking the tires, make sure no wheel nuts are missing, and check for any loose wheel nuts. Tighten if necessary. Tire rotation* — Tires should be rotated every 7,500 miles (12,000 km). Wheel alignment and balance — If the vehicle should pull to either side while driv- ing on a straight and level road, or if you detect uneven or abnormal tire wear, there may be a need for a wheel alignment. If the steering wheel or seat vibrates at normal highway speeds, wheel balancing may be needed. Windshield wiper blades* — Check for cracks or wear if they do not wipe properly. Doors and hood — Check that all doors and the hood operate properly. Also ensure that all latches lock securely. Lubricate hinges, latches, rollers and links if neces- sary. Make sure the secondary latch keeps the hood from opening when the primary latch is released. When driving in areas using road salt or other corrosive materials, check lubrication frequently. INTERIOR MAINTENANCE The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the vehicle, etc. Additional information on the following items with an ‘‘*’’ is found in the ‘‘Do-it- yourself’’ section of this manual. Lights* — Make sure the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Warning lights and buzzers/chimes — Make and buzzers/chimes are operating properly. Windshield wiper and washer* — Check that the wipers and washer operate properly and that the wipers do not streak. Windshield defroster — Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner. all warning lights sure Steering wheel — Check for changes in the steering conditions, such as excessive freeplay, hard steering or strange noises. Seats — Check seat position controls such

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2000 Nissan Quest Owners Manual