2012 Nissan Murano Owners Manual

Download PDF Manual
revolutions per minute (RPM). Do not rev the engine into the red zone *1 . CAUTION When engine speed approaches the red zone, shift to a higher gear or reduce engine speed. Operating the engine in the red zone may cause serious engine damage. ENGINE COOLANT TEMPERATURE GAUGE GUID-5D79A6DB-7B0E-48CD-B3D5-38EB0D89F9F4 The gauge indicates the engine coolant tem- perature. The engine coolant temperature is within the normal range when the gauge needle points within the zone *1 The engine coolant temperature varies with the outside air temperature and driving conditions. shown in the illustration. CAUTION If the gauge indicates engine coolant temperature near the hot (H) end of the [ Edit: 2011/ 7/ 18 Model: Z51-D ] Instruments and controls 2-7 Black plate (96,1) COMPASS (if so equipped) GUID-56AB49A5-E009-4FD9-864E-78F14A1329E1 SIC3181 When the ignition switch is pushed to the ON position, the compass display *B will indicate the direction of the vehicle’s heading. NOS1741 If the display reads “C”, calibrate the compass by driving the vehicle in 3 complete circles at less than 5 MPH (8 km/h). You can also calibrate the compass by driving your vehicle tank when the fuel gauge needle reaches “E”. The located on the driver’s side of the vehicle. indicates that the fuel-filler door is CAUTION If the vehicle runs out of fuel, the malfunction indicator light (MIL) may come on. Refuel as soon as possible. After a few driving trips, the light should turn off. If the light remains on after a few driving trips, have the vehicle inspected by a NISSAN dealer. . For additional information, see “Malfunction Indicator Light (MIL)” later in this section. [ Edit: 2011/ 7/ 18 Model: Z51-D ] JVI0338X FUEL GAUGE GUID-7C88D297-60D4-4310-84BB-E1EC1735E409 The gauge indicates the approximate fuel level in the tank. The gauge may move slightly during braking, turning, acceleration, or going up or down hills. The gauge needle returns to E (Empty) after the ignition switch is pushed to the OFF position. Refill the fuel registers “E” (Empty). The low fuel warning appears on the dot matrix liquid crystal display when the fuel level in the tank is getting low. Refuel as soon as it is convenient, preferably before the gauge reaches “E”. There will be a small reserve of fuel in the tank before the gauge 2-8 Instruments and controls Black plate (97,1) on your everyday route. The compass will be calibrated once it has tracked 3 complete circles. To turn on and off the compass manually, push switch *A while the ignition switch is in the the ON position. Zone map SIC0611B Instruments and controls 2-9 [ Edit: 2011/ 7/ 18 Model: Z51-D ] Black plate (98,1) ZONE VARIATION CHANGE PROCE- DURE GUID-0E831674-32EA-49CF-AB30-0F9EEEB78E33 The difference between magnetic north and geographical north is known as variance. In some areas, this difference can sometimes be great enough to cause false compass readings. Follow these instructions to set the variance for your particular location if this happens: 1. Push the switch for more than 3 seconds. The current zone number will appear in the display. 2. Find your current location and variance number on the zone map. NOTE: Use zone number 5 for Hawaii. pass point when the vehicle moves to an area where the geomagnetism is stabilized.) CAUTION . Do not install a ski rack, antenna, etc., which are attached to the vehicle by means of a magnet. They affect the operation of the compass. . When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as it may cause the liquid cleaner to enter the mirror housing. 3. Push the switch repeatedly until the new zone number appears in the display, then release the switch. After you release the switch, the display will show a compass direction within a few seconds. If the compass deviates from the correct indication soon after repeated adjust- ment, have the compass checked at a NISSAN dealer. . The compass may not indicate the correct compass point in tunnels or while driving up or down a steep hill. (The compass returns to the correct com- 2-10 Instruments and controls [ Edit: 2011/ 7/ 18 Model: Z51-D ] Black plate (99,1) WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS GUID-6AC4475F-D514-4474-861E-A33DFE4DFCFD All-Wheel Drive (AWD) warning light (AWD models) Anti-lock Braking System (ABS) warning light Brake warning light Charge warning light Master warning light Seat belt warning light Low beam indicator light Malfunction Indicator Light (MIL) Supplemental air bag warning light Overdrive off indicator light Vehicle Dynamic Control (VDC) warning light All-Wheel Drive (AWD) LOCK indicator light (AWD models) Continuously Variable Transmission (CVT) position indicator light Soft top indicator light (CrossCabriolet models) Turn signal/hazard indicator lights Vehicle Dynamic Control (VDC) off indicator light Engine oil pressure warning light Cruise indicator light Intelligent Key warning light Front passenger air bag status light Low tire pressure warning light High beam indicator light [ Edit: 2011/ 7/ 18 Model: Z51-D ] Instruments and controls 2-11 CHECKING BULBS GUID-B5546604-D327-4511-B24A-C4F4615F5F1F With all doors closed, apply the parking brake and push the ignition switch to the ON position without starting the engine. The following lights will come on (if so equipped): or The following lights come on briefly and then go off (if so equipped): or If any light does not come on, it may indicate a burned-out bulb or an open circuit in the electrical system. Have the system checked by a NISSAN dealer. Some indicators and warnings are also dis- played on the dot matrix crystal display on the speedometer. (See “Dot matrix liquid crystal display” later in this section.) Black plate (100,1) WARNING LIGHTS GUID-39AE13E8-806F-40A7-8C69-3AF4A1790761 All-Wheel Drive (AWD) warning light (AWD models) GUID-2C7F9D36-036A-4856-8580-AE4D2A3CACAA The light comes on when the ignition switch is pushed to ON. It turns off soon after the engine is started. If the AWD system malfunctions, or the diameter of the front and the rear wheels are different, the warning light will either remain illuminated or blink. (See “All-Wheel Drive (AWD)” in the “5. Starting and driving” section.) CAUTION If the warning light comes on while driving there may be a malfunction in the AWD system. Reduce the vehicle speed and have your vehicle checked by a NISSAN dealer as soon as possible. If the AWD warning light blinks when you are driving: — blinks rapidly (about twice a second): Pull off the road in a safe area, and idle the engine. The driving mode will change to 2WD to prevent the AWD system from malfunctioning. If the warning light turns off, you can drive again. — blinks slowly (about once every 2 seconds): Pull off the road in a safe area, and idle the engine. Check that all tire sizes are the same, tire pressure is correct and tires are not worn. If the warning light is still on after the above operations, have your vehicle checked by a NISSAN dealer as soon as possible. or Anti-lock Braking System (ABS) warning light GUID-06CAAC80-C465-4A21-9EB7-C024333BA100 When the ignition switch is in the ON position, the Anti-lock Braking System (ABS) warning light illuminates and then turns off. This indicates the ABS is operational. If the ABS warning light illuminates while the engine is running, or while driving, it may indicate the ABS is not functioning properly. Have the system checked by a NISSAN dealer. If an ABS malfunction occurs, the anti-lock function is turned off. The brake system then operates normally, but without anti-lock assis- 2-12 Instruments and controls [ Edit: 2011/ 7/ 18 Model: Z51-D ] tance. (See “Brake system” in the “5. Starting and driving” section.) or Brake warning light GUID-4A67DFC2-D59E-4197-BAD5-168A3CE40A7E This light functions for both the parking brake and the foot brake systems. Parking brake indicator: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 When the ignition switch is in the ON position, the light comes on when the parking brake is applied. Low brake fluid warning light: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 When the ignition switch is in the ON position, the light warns of a low brake fluid level. If the light comes on while the engine is running with the parking brake not applied, stop the vehicle and perform the following: 1. Check the brake fluid level. Add brake fluid as necessary. (See “Brake fluid” in the “8. Maintenance and do-it-yourself” section.) If the brake fluid level is correct, have the warning system checked by a NISSAN dealer. 2. Anti-lock Braking System (ABS) warning indicator: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 When the parking brake is released and the brake fluid level is sufficient, if both the brake warning light and the Anti-lock Braking System (ABS) warning light illuminate, it may indicate Black plate (101,1) the ABS is not functioning properly. Have the brake system checked, and if necessary re- paired, by a NISSAN dealer promptly. (See “Anti-lock Braking System (ABS) warning light” earlier in this section.) WARNING . Your brake system may not be working properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive care- fully to the nearest service station for repairs. Otherwise, have your vehicle towed because driving it could be dangerous. . Pressing the brake pedal with the engine stopped and/or low brake fluid level may increase your stop- ping distance and braking will re- quire greater pedal effort as well as pedal travel. If the brake fluid level is below the minimum or MIN mark on the brake fluid reservoir, do not drive until the brake system has been checked at a NISSAN dealer. Charge warning light GUID-69B03338-0451-441C-B766-BECF7DE9BC90 If the light comes on while the engine is running, it may indicate the charging system is not functioning properly. Turn the engine off and check the alternator belt. If the belt is loose, broken, missing or if the light remains on, see a NISSAN dealer immediately. CAUTION Do not continue driving if the alternator belt is loose, broken or missing. Engine oil pressure warning light GUID-0AE5784C-961F-4FC8-BFAF-77A224D6D347 This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call a NISSAN dealer or other authorized repair shop. The engine oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. (See “Engine oil” in the “8. Maintenance and do-it- yourself” section.) Instruments and controls 2-13 [ Edit: 2011/ 7/ 18 Model: Z51-D ] CAUTION Running the engine with the engine oil pressure warning light on could cause serious damage to the engine almost immediately. Such damage is not cov- ered by warranty. Turn off the engine as soon as it is safe to do so. Intelligent Key warning light GUID-0700CAF3-DF55-4F0A-A342-324495D014C0 After the ignition switch is pushed to the ON position, this light comes on for about 2 seconds and then turns off. This light warns of a malfunction with the Intelligent Key system. the light comes on while the engine is If stopped, the engine. If the light comes on while the engine is running, you can drive the vehicle. However in these cases, contact a NISSAN dealer for repair as soon as possible. it may be impossible to start Black plate (102,1) Low tire pressure warning light GUID-2FD87A32-C17B-42A1-B740-5A7539F98F4B Your vehicle is equipped with a Tire Pressure Monitoring System (TPMS) that monitors the tire pressure of all tires except the spare. The low tire pressure warning light warns of low tire pressure or indicates that the TPMS is not functioning properly. After the ignition switch is pushed ON, this light illuminates for about 1 second and turns off. the warning light will Low tire pressure warning: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 If the vehicle is being driven with low tire pressure, illuminate. A CHECK TIRE PRESSURE warning also appears on the dot matrix liquid crystal display. When the low tire pressure warning light illuminates, you should stop and adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label. The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted. After the tire is inflated to the recommended pressure, the vehicle must be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light. Use a tire pressure gauge to check the tire pressure. The CHECK TIRE PRESSURE warning is active as long as the low tire pressure warning light remains illuminated. For additional information, see “Dot matrix liquid crystal display” later in this section, “Tire Pressure Monitoring System (TPMS)” in the “5. Starting and driving” section and “Tire Pressure Monitoring System (TPMS)” in the “6. In case of emergency” section. TPMS malfunction: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 If the TPMS is not functioning properly, the low tire pressure warning light will flash for approxi- mately 1 minute when the ignition switch is pushed ON. The light will remain on after the 1 minute. Have the system checked by a NISSAN dealer. The CHECK TIRE PRESSURE warning does not appear if the low tire pressure warning light illuminates to indicate a TPMS malfunction. For additional information, see “Tire Pressure Monitoring System (TPMS)” in the “5. Starting and driving” section. For the CHECK TIRE PRESSURE warning, see “Dot matrix liquid crystal display” later in this section. WARNING If the light does not illuminate with the ignition switch pushed ON, have the vehicle checked by a NISSAN dealer as soon as possible. 2-14 Instruments and controls [ Edit: 2011/ 7/ 18 Model: Z51-D ] . If the light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Driving with un- der-inflated tires may permanently damage the tires and increase the likelihood of tire failure. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If the light still illuminates while driv- ing after adjusting the tire pressure, a tire may be flat. If you have a flat tire, replace it with a spare tire as soon as possible. . When a spare tire is mounted or a wheel is replaced, the TPMS will not function and the low tire pressure warning light will flash for approxi- mately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/ or system resetting. . Replacing tires with those not ori- ginally specified by NISSAN could affect the proper operation of the TPMS. CAUTION The TPMS is not a substitute for the regular tire pressure check. Be sure to check the tire pressure regularly. If the vehicle is being driven at speeds of less than 16 MPH (25 km/h), the TPMS may not operate correctly. . Be sure to correctly install the specified size of tires to the four wheels. Master warning light GUID-6AB3A8A0-B446-4089-A66C-618A6659F580 When the ignition switch is in the ON position, the master warning light illuminates if any of the following are displayed on the dot matrix liquid crystal display: Black plate (103,1) Low fuel warning Low washer fluid warning . No key warning . Parking brake release warning . Door/lift gate open warning (Hardtop mod- els) . Door/trunk open warning (CrossCabriolet models) Loose fuel cap warning . Check tire pressure warning See “Dot matrix liquid crystal display” later in this section. Seat belt warning light GUID-956FC59D-0351-472F-8CD0-3356E0A21318 The light and chime remind you to fasten seat belts. The light illuminates whenever the ignition switch is pushed to the ON position, and will remain illuminated until the driver’s seat belt is fastened. The seat belt warning light the front passenger will illuminate if the seat belt is not fastened when the front passenger’s seat is occupied. For approximately 5 seconds after the ignition switch is in the ON position, the system does not activate the warning light for the front passenger. See “Seat belts” in the “1. Safety — Seats, seat belts and supplemental restraint system” section for precautions on seat belt usage. for [ Edit: 2011/ 7/ 18 Model: Z51-D ] Instruments and controls 2-15 Black plate (104,1) INDICATOR LIGHTS GUID-BDD7DC61-68C7-435D-8B71-5F80E875AAAB All-Wheel Drive (AWD) LOCK indicator light (AWD models) GUID-B333F845-9EFA-4E8B-A367-0BBBFF6CDC04 This light illuminates when the ignition switch is placed in the ON position, and turns off within 1 second. When selecting the LOCK mode while the engine is running, this light will illuminate. (See “All-Wheel Drive (AWD)” in the “5. Starting and driving” section.) Continuously Variable Transmis- sion (CVT) position indicator light GUID-0130F932-2380-4325-91F5-49DD5E3D8B5F When the ignition switch is pushed to the ON position, the indicator shows the automatic selector shift position. (See “Continuously Vari- able Transmission (CVT)” in the “5. Starting and driving” section.) bags and/or pretensioner systems will not operate in an accident. To help avoid injury to yourself or others, have your vehicle checked by a NISSAN dealer as soon as possible. Vehicle dynamic control (VDC) warning light GUID-9CD9709D-A6B8-4177-B503-4BF50BC0F688 The light will blink when the Vehicle Dynamic Control (VDC) system or the traction control system is operating, thus alerting the driver that the vehicle is nearing its traction limits. The road surface may be slippery. If the VDC warning light comes on and stays on while the VDC system is on, this light alerts the driver to the fact that the VDC system’s fail-safe mode is operating, for example the VDC system may not be functioning properly. Have the If a system checked by a NISSAN dealer. malfunction occurs in the system, the VDC system function will be canceled but the vehicle is still driveable. For additional information, see “Vehicle Dynamic Control (VDC) system” in the “Starting and driving” section of this manual. [ Edit: 2011/ 7/ 18 Model: Z51-D ] Supplemental air bag warning light GUID-C47663FA-9971-432A-840C-6232303C8EC4 After pushing the ignition switch to the ON position, the supplemental air bag warning light will illuminate. The supplemental air bag warning light will turn off after about 7 seconds if the SRS air bag systems are operational. If any of the following conditions occur, the air bags and/or pretensioner systems need servi- cing and your vehicle must be taken to your nearest NISSAN dealer. The supplemental air bag warning light remains on after approximately 7 seconds. The supplemental air bag warning light flashes intermittently. The supplemental air bag warning light does not come on at all. Unless checked and repaired, the Supplemental Restraint Systems (air bag systems) and/or the pretensioners may not function properly. For additional information, see “Supplemental restraint system” in the “1. Safety — Seats, seat belts and supplemental restraint system” sec- tion. WARNING If the supplemental air bag warning light is on, it could mean that the air 2-16 Instruments and controls Cruise indicator light GUID-C4011DB6-8909-4DF3-8C75-17ED51FCED58 Cruise main switch indicator: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 This light illuminates when the cruise control main switch is pushed. The light turns off when the main switch is pushed again. When the cruise main switch indicator light illuminates, the cruise control system is operational. (See “Cruise control” in the “5. Starting and driving” section.) the cruise indicator Cruise malfunction: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 light blinks while the If it may indicate the cruise engine is running, control system is not functioning properly. Have the system checked by a NISSAN dealer. (See “Cruise control” in the “5. Starting and driving” section.) Front passenger air bag status light GUID-1AD6EFB7-D318-4868-99B0-D18664F33C71 The front passenger air bag status light will be lit and the passenger front air bag will be OFF depending on how the front passenger seat is being used. For front passenger air bag status light opera- tion, see “NISSAN Advanced Air Bag System (front seats)” in the “1. Safety — Seats, seat belts and supplemental restraint system” section of this manual. Black plate (105,1) tion/Maintenance (I/M) test” in the “9. Technical and consumer information” section.) Operation: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 The malfunction indicator light will come on in one of two ways: . Malfunction indicator light on steady — An emission control system and/or CVT mal- function has been detected. Check the fuel- filler cap if the LOOSE FUEL CAP warning appears on the dot matrix liquid crystal the fuel-filler cap is loose or display. missing, the cap and continue to drive the vehicle. The light should turn off after a few driving trips. If the light does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer. If tighten or install . Malfunction indicator light blinking — An engine misfire has been detected which may damage the emission control system. To reduce or avoid emission control system damage: — Do not drive at speeds above 45 MPH (72 km/h). — Avoid hard acceleration or deceleration. — Avoid steep uphill grades. Instruments and controls 2-17 High beam indicator light GUID-4EECC9D2-4C62-4418-9FA3-CF0C228A1386 This light comes on when the headlight high beam is on and goes out when the low beam is selected. Low beam indicator light GUID-31C3710D-82FC-41EC-AE8C-69D56A05CEF7 The light comes on when the front park, side marker, tail and license plate lights are on. Malfunction Indicator Light (MIL) the malfunction indicator GUID-6AF8662E-1DE1-45FE-852C-925D132DCE37 If light comes on steady or blinks while the engine is running, it may indicate a potential emission control and/or Continuously Variable Transmission (CVT) mal- function. The malfunction indicator light may also come on steady if the fuel-filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel-filler cap is installed and closed tightly, and that the vehicle has at least 3 US gallons (11.4 liters) of fuel in the fuel tank. After a few driving trips, the light should turn off if no other potential emission control system malfunction exists. If this indicator light remains on for 20 seconds and then blinks for 10 seconds when the engine is not running, it indicates that the vehicle is not ready for an emission control system inspection/ maintenance test. (See “Readiness for Inspec- [ Edit: 2011/ 7/ 18 Model: Z51-D ] Black plate (106,1) CAUTION Operate the soft top with the engine running to prevent a discharged battery. When the soft top is operating, if any of the above conditions are discontinued or any of the following conditions are met, the top will stop operating. . When the selector lever is in the R (Reverse) position. . When the vehicle moves at a speed of 3 MPH (5 km/h) or more. . When the battery voltage is extremely low. . When the temperature of top the soft system becomes extremely high. Release the operating switch, and push it again under the above conditions until the top is fully opened or closed. The soft top indicator light will turn off when the top operation is completely finished. If the soft top indicator light illuminates with the ignition switch ON, it may indicate the electric soft top control unit is not functioning properly. Have your vehicle checked by a NISSAN dealer as soon as possible. For more details about the electric soft top — If possible, reduce the amount of cargo being hauled or towed. The malfunction indicator blinking and remain on. Have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer. light may stop CAUTION Continued vehicle operation without having the emission control system and/or CVT system checked and re- paired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission con- trol system. Overdrive off indicator light GUID-A88B5A9D-E1E7-4ADD-B5C6-FE6EBACFA9C0 The overdrive off indicator light illuminates when the overdrive off mode is selected. For additional information, see “Continuously Variable Transmission (CVT)” in the “5. Starting and driving” section of this manual. Soft top indicator light (Cross- Cabriolet models) GUID-387DFA5A-917F-4E6B-8A1D-1A0AD860A8FA This light illuminates when the soft top is being operated or it is stopped before reaching a full open/close state. When the top is fully opened or closed, the light will turn off. The light blinks while the soft top is not fully opened or closed under the following condi- tions: . When the vehicle is driven. . When the selector lever is in the R (Reverse) position. Be sure to fully open or close the soft top when driving the vehicle. The soft top can be moved with the soft top operating switch only under all of the following conditions: . When the vehicle is stopped. . When the ignition switch is ON. . When the trunk is closed. . When the luggage cover is pulled out and the roof storage area is hooked so that separated from the trunk. . When the selector lever is in a position other than the R (Reverse) position. 2-18 Instruments and controls [ Edit: 2011/ 7/ 18 Model: Z51-D ] Black plate (107,1) DOT MATRIX LIQUID CRYSTAL DISPLAY GUID-8111787A-C29E-4E6F-9310-B498CC7E010D JVI0254X The dot matrix liquid crystal display *1 is located in the speedometer, and it displays, the key operation information and other warn- ings and information. For the detail about the Intelligent Key System, see “Intelligent Key system” in the “3. Pre- driving checks and adjustments” section. operation, see “Soft top (CrossCabriolet mod- els)” in the “3. Pre-driving checks and adjust- ments” section. Turn signal/hazard indicator lights GUID-F77394DF-EFC3-4B65-ACF6-5E0E91264160 The light flashes when the turn signal switch lever or hazard switch is turned on. Vehicle Dynamic Control (VDC) off indicator light GUID-CE6E8B94-E3C1-4EDD-B5CC-1AA8B731382A The light comes on when the Vehicle Dynamic Control (VDC) off switch is pushed to OFF. This indicates that the VDC system is not operating. For additional information, see “Vehicle Dynamic Control (VDC) system” in the “5. Starting and driving” section of this manual. AUDIBLE REMINDERS GUID-854CE725-BA1A-4800-8732-43382E89CE05 Key reminder chime GUID-03B79EB0-07EF-4F48-9DFC-C531CF03B6F2 A chime will sound if the driver side door is opened while the ignition switch is pushed to the ACC position or pushed to the OFF or LOCK position with the Intelligent Key left in the Intelligent Key port. Make sure the ignition switch is pushed to the OFF position, and take the Intelligent Key with you when leaving the vehicle. Light reminder chime GUID-7B425B53-6E2D-43C2-AE08-9F717545E029 A chime will sound when the driver side door is opened with the light switch in the or position and the ignition switch in the ACC or OFF position. Turn the light switch off when you leave the vehicle. Parking brake reminder chime GUID-16CE9E88-5960-4CAA-845D-8ACC44A8DB19 The chime will sound if the vehicle is driven at more than 4 MPH (7 km/h) with the parking brake applied. Stop the vehicle and release the parking brake. Seat belt warning chime GUID-6CB52CBC-6585-437E-BC4E-959C5BB57A7B The chime will sound for about 6 seconds unless the driver’s seat belt is securely fastened. Brake pad wear warning GUID-A531CD6C-63DF-4083-A7B6-FC8F79CA75A0 The disc brake pads have audible wear warn- ings. When a brake pad requires replacement, it will make a high pitched scraping sound when the vehicle is in motion. This scraping sound will first occur only when the brake pedal is depressed. After more wear of the brake pad, the sound will always be heard even if the brake pedal is not depressed. Have the brakes checked as soon as possible if the warning sound is heard. [ Edit: 2011/ 7/ 18 Model: Z51-D ] Instruments and controls 2-19 Black plate (108,1) GUID-2BC84707-B5D6-420C-AF4E-599CBE87C0AA OPERATIONAL INDICATORS 1. Engine start operation indicator GUID-D97EB6AE-486E-4B90-8447-B6FE87D4AD91 This indicator appears when the selector lever is in the P (Park) position. This indicator means that the engine will start by 2-20 Instruments and controls pushing the ignition switch with the brake pedal depressed. You can start the engine directly in any position. [ Edit: 2011/ 7/ 18 Model: Z51-D ] JVI0355X 2. Key insertion indicator GUID-05110D15-ABEF-44EB-A8DB-34AB9197B4B8 This indicator appears when the key needs to be inserted into the key port. (For example, the Intelligent Key battery is discharged.) If this indicator appears, insert the key into the key port in the correct direction. (See “Push- Black plate (109,1) button ignition switch” in the “5. Starting and driving” section.) 3. Key removal indicator GUID-BB5416CE-8D01-47D1-8C3E-4F7E493AE6E1 This indicator appears when the driver’s door is opened with the ignition switch in the OFF or LOCK position and the key placed in the key port. A key reminder chime also sounds. If this indicator appears, remove the key from the key port and take it with you when leaving the vehicle. 4. NO KEY warning GUID-F57235F8-65EC-43AC-9534-39FFBAF7DBAD This warning appears in either of the following conditions. No key inside the vehicle: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 The warning appears when the door is closed with the Intelligent Key left outside the vehicle and the ignition switch in the ACC or ON position. Make sure that the Intelligent Key is inside the vehicle. Unregistered key: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 The warning appears when the ignition switch is pushed from the LOCK position and the key cannot be recognized by the system. You cannot start the engine with an unregistered key. Use the registered key. See “Intelligent Key system” in the “3. Pre- driving checks and adjustments” section for more details. 5. SHIFT “P” warning GUID-F63536DD-DDB8-49FB-8271-F811D25EC8A1 This warning appears when the ignition switch is pushed to stop the engine with the selector lever in any position except the P (Park) position. If this warning appears, move the selector lever to the P (Park) position or push the ignition switch to the ON position. An inside warning chime will also sound. (See “Intelligent Key system” in the “3. Pre-driving checks and adjustments” section.) 6. “PUSH” warning GUID-2B3DB981-A402-45B6-B5BB-474886B28E6A This warning appears when the selector lever is moved to the P (Park) position with the ignition switch in the ACC position after the SHIFT “P” warning appears. To push the ignition switch to the OFF position, perform the following procedure: SHIFT “P” warning ? (Move the selector lever to “P”) ? PUSH warning ? (Push the ignition switch ? ignition switch position is turned to ON) ? PUSH warning ? (Push the ignition switch ? ignition switch position is turned to OFF) 7. Key battery discharge indicator GUID-4EDE548E-8FF0-4D46-ABCB-68B647C3999A This indicator appears when the key battery is running out of power. If this indicator appears, replace the battery with a new one. (See “Intelligent key battery replace- ment” in the “8. Maintenance and do-it-yourself” section.) 8. Parking brake release warning GUID-834CC27F-8812-483E-9320-C2D89C3E4B39 This warning appears when the vehicle speed is above 4 MPH (7 km/h) and the parking brake is applied. Stop the vehicle and release the parking brake. 9. Low fuel warning GUID-15EF772B-A9F6-4FC2-AB15-CABF1BB1DF48 This warning appears when the fuel level in the tank is getting low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches the empty (E) position. There is a small reserve of fuel remaining in the tank when the fuel gauge reaches the empty (E) position. 10. Low washer fluid warning GUID-75BFB25F-0C2B-423E-890D-9368CFA667DD This warning appears when the washer tank fluid is at a low level. Add washer fluid as necessary. (See “Window washer fluid” in the “8. Main- tenance and do-it-yourself” section.) Instruments and controls 2-21 [ Edit: 2011/ 7/ 18 Model: Z51-D ] Black plate (110,1) SIC4237 section and “Tire Pressure Monitoring System (TPMS)” in the “5. Starting and driving” section.) 15. “TIMER” indicator GUID-FF6A1FD2-B5C4-4083-B2CA-3E728C17C633 This indicator appears when the set “TIMER” indicator activates. You can set the time for up to 6 hours. in this section.) (See “Trip computer” later 16. Low outside temperature warning GUID-84D86BBA-1B59-4DDE-9353-177DB0D95B81 This warning appears if the outside temperature is below 378F (38C). The warning can be set not to be displayed. (See “Trip computer” later in this section.) 11. Door/lift gate open warning (ignition switch is in the ON position) (Hardtop models) GUID-E8BF5142-318A-41D5-8AB1-86843D59BCCF This warning appears if any of the doors and/or the lift gate are open or not closed securely. The vehicle icon indicates which door is open on the display. 12. Door/trunk open warning (ignition switch is in the ON position) (Cross- Cabriolet models) GUID-CE5E7381-F4E7-4E9D-8BC1-5FDCD9D031B0 This warning appears if any of the doors and/or the trunk are open or not closed securely. The vehicle icon indicates which door is open on the display. 13. Loose fuel cap warning GUID-BF7DA770-AB4E-4465-8317-1B41831C3607 This warning appears when the fuel-filler cap is not tightened correctly after the vehicle has been refueled. (See “Fuel-filler cap” in the “3. Pre-driving checks and adjustments” section.) 14. Check tire pressure warning GUID-0DD3569E-5223-4496-8B17-789648E1715D This warning appears when the low tire pressure warning light in the meter illuminates and low tire pressure is detected. If this warning appears, stop the vehicle and adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label. (See “Low tire pressure warning light” earlier in this 2-22 Instruments and controls [ Edit: 2011/ 7/ 18 Model: Z51-D ] MAINTENANCE INDICATORS GUID-0A851647-6BB2-4E92-AEB5-E04319FCA2E4 1. Engine oil replacement indicator GUID-9CEF8B90-48A9-4FB5-BFD9-0CF43586EC4F This indicator appears when the customer set time comes for changing the engine oil. You can set or reset the distance for changing the engine oil. (See “Trip computer” later in this section.) 2. Oil filter replacement indicator GUID-C344252D-B1CB-46F2-AEAD-7C37EC262221 This indicator appears when the customer set time comes for replacing the oil filter. You can set or reset the distance for replacing the oil filter. (See “Trip computer” later in this section.) 3. Tire replacement indicator GUID-1A74526D-9B7C-43A3-95CF-62EFC05FBC61 This indicator appears when the customer set distance comes for replacing tires. You can set or reset the distance for replacing tires. (See “Trip computer” later in this section.) WARNING The tire replacement indicator is not a substitute for regular tire checks, in- cluding tire pressure checks. See “Changing wheels and tires” in the “Maintenance and do-it-yourself” sec- tion. Many factors including tire infla- tion, alignment, driving habits and road conditions affect tire wear and when tires should be replaced. Setting the tire replacement indicator for a certain driving distance does not mean your tires will last that long. Use the tire replacement indicator as a guide only and always perform regular tire checks. Failure to perform regular tire checks, including tire pressure checks could result in tire failure. Serious vehicle damage could occur and may lead to a collision, which could result in serious personal injury or death. 4. “OTHER” indicator GUID-17015DA7-2755-4CAC-AF46-619CAF47DE9D This indicator appears when the customer set time comes for replacing items other than the engine oil, oil filter and tires. You can set or reset the distance for replacing the items. (See “Trip computer” later in this section.) More maintenance reminders are also available on the center display (if so equipped). (See “How to use INFO button” in the “4. Monitor, heater, air conditioner, audio, phone and voice recognition systems” section.) Black plate (111,1) SIC3580 switch switch TRIP COMPUTER GUID-F63231D7-123A-4BC6-844C-BA3C14A5C066 Switches for the trip computer are located on the right side of the combination meter panel. To operate the trip computer, push the side or front of the switches as shown above. *A *B When the ignition switch is pushed to the ON position, modes of the trip computer can be selected by pushing the switch *A Each time the display will change as follows: Current and average fuel consumption ? Average fuel consumption and speed ? switch *A . is pushed, the [ Edit: 2011/ 7/ 18 Model: Z51-D ] Instruments and controls 2-23 Black plate (112,1) Elapsed time and trip odometer ? Distance to empty (dte) ? Outside air temperature (ICY) ? Setting ? Warning check JVI0251X SIC3674 Current and average fuel consumption (MPG, l (liter)/100 km) GUID-C03B6A5C-9ED7-43A7-9BC4-010DAD1E69BD The current and average fuel consumption mode shows the current and average fuel consump- tion. Average fuel consumption (MPG, l/100 km) and speed (MPH or km/h) GUID-5567CAAC-37CB-49C0-8903-54489EC24183 Fuel consumption: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 The average fuel consumption mode shows the average fuel consumption since the last reset. switch *B Resetting is done by pushing the for longer than 1 second. (The average speed is also reset at the same time.) The display is updated every 30 seconds. At about the first 1/3 mile (500 m) after a reset, the display shows “——”. Speed: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 The average speed mode shows the average vehicle speed since the last reset. Resetting is 2-24 Instruments and controls [ Edit: 2011/ 7/ 18 Model: Z51-D ] switch *B for longer done by pushing the than 1 second. (The average fuel consumption is also reset at the same time.) The display is updated every 30 seconds. The first 30 seconds after a reset, the display shows “——”. Black plate (113,1) SIC4701 SIC4702 Elapsed time and trip odometer (miles or km) GUID-FEA80D52-9DA7-4A2D-BD49-7619EBBECCF9 Elapsed time: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 The elapsed time mode shows the time since the last reset. The displayed time can be reset switch *B for longer than 1 by pushing the second. (The trip odometer is also reset at the same time.) Trip odometer: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 The trip odometer mode shows the total distance the vehicle has been driven since the last reset. Resetting is done by pushing the switch *B than 1 second. elapsed time is also reset at the same time.) longer (The for Distance to empty (dte — miles or km) GUID-6D35B21A-8E00-4687-AB2C-E21288A7467A The distance to empty (dte) mode provides you with an estimation of the distance that can be driven before refueling. The dte is constantly being calculated, based on the amount of fuel in the fuel tank and the actual fuel consumption. The display is updated every 30 seconds. The dte mode includes a low range warning feature. level is low, the warning is displayed on the screen. When the fuel display will change to “——”. If the amount of fuel added is small, the display just before the ignition switch is level drops even lower, the dte If the fuel [ Edit: 2011/ 7/ 18 Model: Z51-D ] Instruments and controls 2-25 Black plate (114,1) pushed to the OFF position may continue to be displayed. . When driving uphill or rounding curves, the fuel in the tank shifts, which may momenta- rily change the display. SIC4703 SIC3678 Outside air temperature (ICY — 8F or 8C) GUID-1F0F141E-7E24-493C-9ABE-8A75128A7804 The outside air temperature is displayed in 8F or 8C in the range of −22 to 1408F (−30 to 608C). The outside air temperature mode includes a low temperature warning feature. If the outside air temperature is below 378F (38C), the warning is displayed on the screen. The outside temperature sensor is located in front of the radiator. The sensor may be affected by road or engine heat, wind directions and other driving conditions. The display may differ from the actual outside temperature or the temperature displayed on various signs or bill- boards. Setting GUID-180A1674-9E9A-45F6-9ECF-354F636CDD00 Setting cannot be made while driving. A message “Setting can only be operated when stopped” is also displayed on the dot matrix crystal display. switch *B are switch *A and The used in the setting mode to select and decide a menu. SKIP: Push the check mode. Push the GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 switch *A to move to the warning switch *B to select other menus. 2-26 Instruments and controls [ Edit: 2011/ 7/ 18 Model: Z51-D ] Black plate (115,1) To return to the top page of the setting mode, select “BACK”. ALERT: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 Alert menu can be set to notify the following items. TIMER Select this submenu to specify when the “TIMER” indicator activates. ICY Select outside temperature warning. this submenu to display the low To return to the top page of the setting mode, select “BACK”. MAINTENANCE: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 The maintenance intervals of the following items can be set or reset for the reminders. . OIL this submenu to set or reset this submenu to set or reset Select distance for changing the engine oil. FILTER Select distance for replacing the oil filter. TIRE Select distance for replacing tires. this submenu to set or reset the the the GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 to your OPTIONS: The 3 option menus can be set preference. LANGUAGE Select French or Spanish for display. this submenu to choose English, . UNIT Select this submenu to choose the unit from MPG or l/100 km. . EFFECTS the dial effects this menu to set Select described below to on or off. — The indicator needles sweep in the meters and the ring illumination will be brightened gradually when the engine is started. To return to the top page of the setting mode, select “BACK”. . OTHER Select this submenu and set or reset the distance for replacing items other than the engine oil, oil filter and tires. [ Edit: 2011/ 7/ 18 Model: Z51-D ] SIC3993 Warning check GUID-FF3DCF80-E792-4B60-B3EB-0786D9710BD7 To see if there are any of the following warnings and corresponding details, select this menu. . No key warning . Parking brake release warning . Door/lift gate open warning (Hardtop mod- Low fuel warning Low washer fluid warning els) . Door/trunk open warning (CrossCabriolet models) Loose fuel cap warning Instruments and controls 2-27 . Check tire pressure warning SKIP: Push the check display. Push the menus. switch *A GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 to exit the warning switch *B to select DETAIL DETAIL: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 This item is available only when a warning is displayed. Select this menu to see the details of warnings. SECURITY SYSTEMS GUID-5B8EE3AC-B3AC-45D4-BF38-6AC7583B2D4C SIC2133 Your vehicle has two types of security systems, as follows: . Vehicle security system (if so equipped) . NISSAN Vehicle Immobilizer System The security condition will be shown by the security indicator light. Black plate (116,1) VEHICLE SECURITY SYSTEM (if so equipped) GUID-3A2129E5-3F98-44E7-8D33-56C1DC801E7A The vehicle security system provides visual and audio alarm signals if someone opens the doors or lift gate/trunk when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs. The system helps deter vehicle theft but cannot prevent it, nor can it prevent the theft of interior or exterior vehicle components in all situations. Always secure your vehicle even if parking for a brief period. Never leave your keys in the vehicle, and always lock it when unattended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible. Many devices offering additional protection, such as component locks, identification markers, and tracking systems, are available at auto supply stores and specialty shops. Your NISSAN dealer may also offer such equipment. Check with your insurance company to see if you may be eligible for discounts for various theft protection features. 2-28 Instruments and controls [ Edit: 2011/ 7/ 18 Model: Z51-D ] Black plate (117,1) The alarm is activated by: . Unlocking the door or opening the lift gate/ trunk without using the button on the Intelligent Key, the request switch or the key. (Even if the door is opened by releasing the door inside lock knob, the alarm will activate.) How to stop an activated alarm GUID-3A47058D-D66F-43FA-8D5B-CE27C3B3E4A6 The alarm will stop by unlocking a door by pushing the unlock button on the Intelligent Key, pushing the request switch or using the key. The alarm will not stop if the ignition switch is placed in the ACC or ON position. If the system does not operate as de- scribed above, have it checked by a NISSAN dealer. NISSAN VEHICLE IMMOBILIZER SYS- TEM GUID-140A6D7E-5E78-4398-9FB4-FDC469E689FE The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of the registered key. Never leave these keys in the vehicle. For USA: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful Instruments and controls 2-29 5. Confirm that the security indicator light *A comes on. The security indicator light stays on for about 30 seconds. The vehicle security system is now pre-armed. After about 30 seconds the vehicle security system automatically shifts into the armed phase. The security light begins to flash once every approximately 3 seconds. If, during this 30-second pre-arm time period, the door is unlocked, or the ignition switch is pushed to ACC or ON, the system will not arm. Even when the driver and/or passengers are in the vehicle, the system will activate with all doors and lift gate/trunk locked with the ignition switch in the LOCK position. When pushing the ignition switch to the ACC or ON position, the system will be released. Vehicle security system activation GUID-D932FA41-7646-4669-AA61-035AB796F12C The vehicle security system will give the follow- ing alarm: The headlights blink and the horn sounds intermittently. The alarm automatically turns off after approximately 1 minute. However, the alarm reactivates if the vehicle is tampered with again. [ Edit: 2011/ 7/ 18 Model: Z51-D ] SIC1699A How to arm the vehicle security system 1. Close all windows. GUID-E45D0EB0-DDEE-43F9-BCF5-4FFD6F801B10 The system can be armed even if the windows are open. 2. Push the ignition switch to the OFF position. 3. Carry the Intelligent Key. 4. Close all doors and lift gate/trunk. Lock all the lock button door. The doors can be locked with: . any request switch the power door lock switch the key — master or mechanical on the Intelligent Key Black plate (118,1) service as soon as possible. Please bring all registered keys that you have when visiting a NISSAN dealer for service. interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: Changes or modifications not ex- pressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. For Canada: This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any inter- ference, including interference that may cause undesired operation of the device. SIC1699A GUID-DBC33161-BF46-4EE3-8435-AB868C640CC4 indicates the the NISSAN Vehicle Immobilizer Security indicator light The security indicator light *A status of System. The light blinks after the ignition switch was in the ACC, OFF and LOCK position. This function indicates the security systems equipped on the vehicle are operational. If the NISSAN Vehicle Immobilizer System is malfunctioning, this light will remain on while the ignition switch is in the ON position. If the light still remains on and/or the engine will not start, see a NISSAN dealer for NISSAN Vehicle Immobilizer System 2-30 Instruments and controls [ Edit: 2011/ 7/ 18 Model: Z51-D ] reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate and water. WINDSHIELD WIPER AND WASHER SWITCH GUID-15F1CDB4-078A-4D01-A331-3BCB3082F46B WARNING In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm windshield with the defroster before you wash the windshield. CAUTION . Do not operate the washer continu- ously for more than 30 seconds. . Do not operate the washer if the reservoir tank is empty. . Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank. . Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer [ Edit: 2011/ 7/ 18 Model: Z51-D ] Black plate (119,1) Type A SIC3664 SIC4395 Type B Instruments and controls 2-31 Black plate (120,1) washer. Then the wiper will also operate several times. SIC4017 RAIN-SENSING AUTO WIPER SYS- TEM (if so equipped) GUID-05A0C0C8-F56A-4E1F-90FD-7DD9CB5E2B3F The rain-sensing auto wiper system can auto- matically turn on the wipers and adjust the wiper speed depending on the rainfall and the vehicle speed by using the rain sensor located on the upper part of the windshield. To set the rain-sensing auto wiper system, push the lever down to the AUTO position *1 . The wiper will sweep once while the ignition switch is in the ON position. The rain sensor sensitivity level can be adjusted by turning the knob toward the front *2 (High) or toward the rear *3 (Low). [ Edit: 2011/ 7/ 18 Model: Z51-D ] Type C SIC3922 *1 The windshield wiper and washer operates when the ignition switch is in the ON position. Push the lever down to operate the wiper at the following speed: *1 INT (Type A or Type C) — intermittent operation can be adjusted by turning the knob toward *A (Slower) or *B (Faster). AUTO (Type B) — For models with the rain- sensing auto wiper system, see “Rain-sensing auto wiper system” later in this section. LO — continuous low speed operation HI — continuous high speed operation *2 *3 Push the lever up *4 operation of the wiper. Pull the lever toward you *5 2-32 Instruments and controls (MIST) to have one sweep to operate the . High — High sensitive operation Low — Low sensitive operation To turn the rain-sensing auto wiper system off, push up the lever to the OFF position, or pull down the lever to the LO or HI position. CAUTION Do not touch the rain sensor and around it when the wiper switch is in the AUTO position and the ignition switch is in the ON position. The wipers may operate unexpectedly and cause to an injury or a wiper damage. The rain-sensing auto wipers are in- tended for use during rain. If the switch is left in the AUTO position, the wipers may operate unexpectedly when dirt, fingerprints, oil film or insects are stuck on or around the sensor. The wipers may also operate when exhaust gas or moisture affect the rain sensor. . When the windshield glass is coated with water repellent, the speed of the rain-sensing auto wipers may be higher even though the amount of the rainfall is small. . Be sure to turn off the rain-sensing auto wiper system when you use a car wash. The rain-sensing auto wipers may not operate if rain does not hit the rain sensor even if it is raining. . Using genuine wiper blades is recom- mended for proper operation of the rain-sensing auto wiper system. (See “Windshield wiper blades” in the “8. Maintenance and do-it-yourself” sec- tion for wiper blade replacement.) Black plate (121,1) REAR WINDOW WIPER AND WASHER SWITCH (Hardtop models) GUID-E9B01D50-BAE9-400D-AF33-89486215C486 WARNING In freezing temperatures the washer solution may freeze on the rear window glass and obscure your vision. Warm the rear window with the defroster before you wash the rear window. CAUTION . Do not operate the washer continu- ously for more than 30 seconds. . Do not operate the washer if the reservoir tank is empty. . Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank. . Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the Instruments and controls 2-33 [ Edit: 2011/ 7/ 18 Model: Z51-D ] Black plate (122,1) The rear window wiper and washer operate when the ignition switch is in the ON position. Turn the switch clockwise from the OFF position to operate the wiper. *1 Intermittent (INT) — intermittent operation (not adjustable) *2 Low (ON) — continuous low speed operation Push the switch forward *3 to operate the washer. Then the wiper will also operate several times. window washer reservoir tank to mix the washer fluid concentrate and water. If the rear window wiper operation is interrupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice that is on and around the wiper arms. In approxi- mately 1 minute, turn the switch on again to operate the wiper. Type A SIC3666 2-34 Instruments and controls Type B SIC4019 [ Edit: 2011/ 7/ 18 Model: Z51-D ] REAR WINDOW AND OUTSIDE MIRROR DEFROSTER SWITCH GUID-6A8EA538-4B5A-4260-A4F9-59AA6EEC9D6A To defog/defrost the rear window glass and outside mirrors (if so equipped), start the engine and push the switch *1 on. The indicator light *2 will come on. Push the switch again to turn the defroster off. It will automatically turn off in approximately 15 minutes. CAUTION . When cleaning the inner side of the to rear window, be careful not scratch or damage the rear window defroster. . Do not use the rear window defros- ter switch while the soft top is being operated or fully opened. The heat may damage the soft top material and/or components (CrossCabriolet models). Type A SIC3584 Type B SIC3667 [ Edit: 2011/ 7/ 18 Model: Z51-D ] Black plate (123,1) HEADLIGHT AND TURN SIGNAL SWITCH XENON HEADLIGHTS (if so equipped) GUID-2E72A4A0-1386-460B-B497-869BC1657D74 GUID-DDA42A0C-5BBE-4E9D-9B84-A8C6395E4D9F WARNING HIGH VOLTAGE . When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xenon headlights replaced at a NISSAN dealer. . Xenon headlights provide consider- ably more light than conventional headlights. If they are not correctly aimed, they might temporarily blind an oncoming driver or the driver ahead of you and cause a serious accident. If headlights are not aimed correctly, immediately take your ve- hicle to a NISSAN dealer and have the headlights adjusted correctly. When the xenon headlight is initially turned on, its brightness or color varies slightly. However, the color and brightness will soon stabilize. The life of xenon headlights will be shortened by frequent on-off opera- tion. It is generally desirable not to turn Instruments and controls 2-35 . off the headlights for short intervals (for example, when the vehicle stops at a traffic signal). If the xenon headlight bulb is close to burning out, the brightness will drasti- cally decrease, the light will start blinking, or the color of the light will become reddish. If one or more of the above signs appear, contact a NISSAN dealer. Black plate (124,1) SIC3668 SIC3669 HEADLIGHT SWITCH GUID-996522C0-4578-43C8-83E0-51BB0ADB49B2 Lighting *1 *2 GUID-C1692F98-2EF5-42BF-980D-AA54247F5578 position. Turn the switch to the The front park, side marker, tail, license plate and instrument lights will come on. Turn the switch to the Headlights will come on and all the other lights remain on. position. Autolight system (if so equipped) GUID-8905665A-6EF0-4112-A643-8A502F17847E The autolight system allows the headlights to be set so they turn on and off automatically. To set the autolight system: 1. Make sure the headlight switch is in the AUTO position *1 . 2. Push the ignition switch to the ON position. 3. The autolight system automatically turns the headlights on and off. To turn the autolight system off, turn the switch to the OFF, The autolight system can turn on the headlights automatically when it is dark and turn off the position. or 2-36 Instruments and controls [ Edit: 2011/ 7/ 18 Model: Z51-D ] headlights when it is light. If the ignition switch is pushed to the OFF position and one of the doors is opened and this condition is continued, the headlights remain on for 5 minutes. the period of Automatic headlights off delay: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407 You can keep the headlights on for up to 180 seconds after you push the ignition switch to OFF and open any door then close all the doors. You can adjust the automatic headlights off delay from 0 seconds (OFF) to 180 seconds. The factory default setting is 45 seconds. For automatic headlights off delay setting, see “Vehicle information and settings” in the “4. Monitor, heater, air conditioner, audio, phone and voice recognition systems” section. Black plate (125,1) SAA0642A SIC3670 Be sure not to put anything on top of the photo sensor *A located on the top of the instrument panel. The photo sensor con- trols the autolight; if it is covered, the photo sensor reacts as if it is dark and the headlights will illuminate. Headlight beam select *1 *2 GUID-2ADBA756-362E-41D6-9A9B-2AF1DAC13669 To select the low beam, put the lever in the neutral position as shown. To select the high beam, push the lever forward while the switch is in the it back to select the low beam. Pulling the lever flash the headlight high beam even when the headlight switch is in the OFF position. toward you will position. Pull *3 [ Edit: 2011/ 7/ 18 Model: Z51-D ] Instruments and controls 2-37 Black plate (126,1) SIC3585 the brightness of Instrument brightness control GUID-AE1AD09A-C607-43AF-A5FF-F011B28EA715 The instrument brightness control operates when the ignition switch is in the ON position. To adjust instrument panel lights, push the control switches. Pushing the upper switch *A will brighten the lights. When the brightness reaches the maximum level, a beep will sound. The lower switch *B dims the lights. Repeatedly pushing the lower switch will turn the lights off and a beep will sound. headlights turn off automatically. Daytime running light system (Canada only) GUID-297966B1-EC0F-457B-84B2-00A3EEA09CA5 The daytime running lights automatically illumi- nate when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the OFF position or in the position. Turn the head- light switch to the position for full illumina- tion when driving at night. If the parking brake is applied before the engine is started, the daytime running lights do not illuminate. The daytime running lights illuminate once the parking brake is released. The daytime running lights will remain on until the ignition switch is pushed to the OFF position.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2012 Nissan Murano Owners Manual