X Press the & or % button.
The battery is working properly if battery charge indicator lamp : lights up briefly. If battery charge indicator lamp : does not light up briefly during the test, the key batteries are discharged. X Changing the key battery (Y page 78). i Consult any authorized Mercedes-Benz
Center for a key battery.
i If the battery is tested within the signal
range of the vehicle, you can open or close the vehicle by pressing & or % respectively.
Changing the battery You require a CR 2025 3 V cell battery. X Take the mechanical key out of the
SmartKey (Y page 77).
X Press the mechanical key into the opening
in the SmartKey in the direction of arrow ; until cover : of the battery tray opens. Do not hold the cover closed while doing so.
X Remove the cover of the battery tray. X Repeatedly tap the SmartKey against your
palm until battery = falls out.
X Insert the new battery with the positive
pole facing upwards. Use a lint-free cloth to do so.
X Insert the front tabs of the battery tray's
cover first and then press to close it.
X Check the function of all SmartKey buttons
on the vehicle.
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 79
Version: 3.0.3.5
SmartKey
79
Problems with the SmartKey Problem You cannot lock/ unlock the vehicle using the SmartKey.
Possible causes/consequences and M Solutions The SmartKey battery is discharged or nearly discharged. X Point the tip of the SmartKey at the driver's door handle from a
distance of approximately 1.5 ft (50 cm) and try to unlock or lock the vehicle again.
If this does not work: X Unlock the vehicle using the mechanical key (Y page 77). X Check the key battery and replace it if necessary (Y page 78). The SmartKey is faulty. X Lock the vehicle as described in the "Locking the vehicle
(mechanical key)" section (Y page 82) or unlock it using the mechanical key (Y page 77).
X Have the SmartKey checked at a qualified specialist workshop. KEYLESS-GO is in standby mode because the vehicle has not been unlocked for an extended period. X Pull the door handle twice and then insert the SmartKey into the
ignition lock.
There is a malfunction with KEYLESS-GO. X Lock/unlock the vehicle using the remote control function of the SmartKey. Point the tip of the SmartKey at the driver's door handle from close range and press the %/& button.
X Have the SmartKey checked at a qualified specialist workshop. There is interference from a powerful source of radio waves. X Lock/unlock the vehicle using the remote control function of the SmartKey. Point the tip of the SmartKey at the driver's door handle from close range and press the %/& button.
X Have the SmartKey canceled at an authorized Mercedes-Benz
Center.
X Report the loss immediately to the vehicle insurers. X If necessary, have the locks changed as well.
You can no longer lock/unlock the vehicle using KEYLESS- GO.
You have lost a SmartKey.
You have lost the mechanical key.
X Report the loss immediately to the vehicle insurers. X If necessary, have the locks changed as well.
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 80
Version: 3.0.3.5
80 Doors
Problem The engine cannot be started using the SmartKey.
Possible causes/consequences and M Solutions The on-board voltage is too low. X Switch off non-essential consumers, e.g. seat heating or interior
lighting, and try to start the engine again.
The engine cannot be started using KEYLESS- GO. The SmartKey is in the vehicle.
If this does not work: X Check the starter battery and charge it if necessary
(Y page 308).
or X Jump-start the vehicle (Y page 311). or X Consult a qualified specialist workshop. A door is open. Therefore, the SmartKey cannot be detected as easily. X Close the door and try to start the vehicle again. There is interference from a powerful source of radio waves. X Start your vehicle with the SmartKey in the ignition lock.
Doors Important safety guidelines G Warning! When leaving the vehicle, always remove the SmartKey from the starter switch. Always take the SmartKey with you and lock the vehicle. Do not leave children unattended in the vehicle, even if they are secured in a child restraint system, or with access to an unlocked vehicle. A child's unsupervised access to a vehicle could result in an accident and/or serious personal injury. The children could Rinjure themselves on parts of the vehicle Rbe seriously or fatally injured through
excessive exposure to extreme heat or cold Rinjure themselves or cause an accident with
vehicle equipment that can be operated even if the SmartKey is removed from the starter switch or removed from the vehicle, such as seat adjustment, steering wheel adjustment, or the memory function
If children open a door, they could injure other persons or get out of the vehicle and injure themselves or be injured by following traffic. Do not expose the child restraint system to direct sunlight. The child restraint system's metal parts, for example, could become very hot, and the child could be burned by these parts. G Warning! Do not carry heavy or hard objects in the passenger compartment or cargo compartment unless they are firmly secured in place. Unsecured or improperly positioned cargo increases a child’s risk of injury in the event of Rstrong braking maneuvers Rsudden changes of direction Ran accident
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 81
Version: 3.0.3.5
Doors
81
Unlocking and opening doors from the inside You can open a door from inside the vehicle even if it has been locked, unless the child- proof locks have been activated (Y page 66). Open the door only when the traffic conditions permit. If the vehicle has been opened with the SmartKey or KEYLESS-GO key, opening from inside triggers the anti-theft alarm system. Switch off the alarm (Y page 71).
X Pull door handle ;.
If the door is locked, locking knob : pops up. The door is unlocked and can be opened.
Centrally locking and unlocking the vehicle from the inside The locking or unlocking buttons of the central locking do not lock or unlock the fuel filler flap. The buttons are located on both front doors. i You cannot unlock the vehicle centrally
from the inside if the vehicle has been locked with the SmartKey or KEYLESS-GO.
i It is only possible to lock the vehicle centrally if the front-passenger door is closed.
X To unlock: press button :. X To lock: press button ;.
The vehicle locks when all the doors and the tailgate are closed.
You can open a locked front door from inside the vehicle. Only open the door if traffic conditions allow you to do so. If the vehicle has previously been locked with the central locking button: Rand the KEYLESS-GO key is restored to the
factory settings, the entire vehicle is unlocked if a front door is opened from inside the vehicle.
Rand the KEYLESS-GO key is set to individual
settings, only the front door which is opened from inside the vehicle is unlocked. If the vehicle has been locked centrally with the SmartKey or with KEYLESS-GO, it does not unlock if you use the unlocking button of the central locking.
Automatic locking i The vehicle locks automatically when the
ignition is switched on and the wheels of the vehicle are moving at a speed of more than 9 mph(15 km/h). You may therefore lock yourself out if the vehicle is being pushed, towed, or located on a test rig. You can switch off the automatic locking function via the on-board computer (Y page 208).
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 82
Version: 3.0.3.5
82
Tailgate
Unlocking the driver's door (mechanical key) If the vehicle can no longer be unlocked centrally with the key or KEYLESS-GO: X Take the mechanical key out of the key
(Y page 77).
X Insert the mechanical key into the lock of
the driver's door as far as it will go.
X Turn the mechanical key counter-clockwise as far as it will go to position 1 and hold it in this position.
X Pull the door handle beyond the first
resistance. The locking knob pops up. The door is unlocked.
X Turn the mechanical key back and remove
it.
X Pull the door handle again.
Locking the vehicle Emergency locking If the vehicle can no longer be locked centrally with the SmartKey or KEYLESS-GO: X Close the front-passenger door, the rear door on the front-passenger side and the tailgate.
X Open the driver’s door and the rear door on
the driver’s side.
X Press the locking button on the driver’s
door (Y page 81). The locking knobs in the front-passenger door and in the rear doors drop down.
X Press down the locking knobs in the front-
passenger and rear doors manually, if necessary.
X Close the driver's door from the outside. X Press down the locking knob of the driver's door by reaching in through the open rear door.
i Make sure that you have the vehicle key on your person and that it has not been left in the vehicle.
X Close the rear door on the driver’s side. X Make sure that the doors and the tailgate
are locked.
i If you lock the vehicle as described above,
the fuel filler flap is not locked. The anti- theft alarm system is not activated.
Tailgate Important safety guidelines Do not leave the key in the cargo compartment. You could otherwise lock yourself out. G Warning! When leaving the vehicle, always remove the SmartKey from the starter switch. Always take the SmartKey with you and lock the vehicle. Do not leave children unattended in the vehicle, even if they are secured in a child restraint system, or with access to an unlocked vehicle. A child's unsupervised access to a vehicle could result in an accident and/or serious personal injury. The children could Rinjure themselves on parts of the vehicle Rbe seriously or fatally injured through
excessive exposure to extreme heat or cold Rinjure themselves or cause an accident with
vehicle equipment that can be operated
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 83
Version: 3.0.3.5
Tailgate
83
even if the SmartKey is removed from the starter switch or removed from the vehicle, such as seat adjustment, steering wheel adjustment, or the memory function
If children open a door, they could injure other persons or get out of the vehicle and injure themselves or be injured by following traffic. Do not expose the child restraint system to direct sunlight. The child restraint system's metal parts, for example, could become very hot, and the child could be burned by these parts. G Warning! Do not carry heavy or hard objects in the passenger compartment or cargo compartment unless they are firmly secured in place. Unsecured or improperly positioned cargo increases a child’s risk of injury in the event of Rstrong braking maneuvers Rsudden changes of direction Ran accident G Warning! Make sure the tailgate is closed when the engine is running and while driving. Among other dangers, deadly carbon monoxide (CO) gases may enter vehicle interior resulting in unconsciousness and death.
! The tailgate swings upwards and to the rear when opened. Therefore, make sure that there is sufficient clearance above and behind the tailgate.
To open the tailgate completely, a minimum clearance of 7.20 ft (2.20 m) above the ground is necessary. You can: Ropen and close the tailgate manually from
outside
Ropen and close the tailgate automatically
from outside
Ropen the tailgate manually from inside
Ropen and close the tailgate automatically
from inside
Rlimit the opening angle of the tailgate
Opening and closing from the outside Opening You can only open the tailgate after unlocking it first. X Press the % button on the key.
X Pull handle :. X Raise the tailgate.
Closing G Warning! To prevent possible personal injury, always keep hands and fingers away from the cargo compartment opening when closing the tailgate. Be especially careful when small children are around.
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 84
Version: 3.0.3.5
84
Tailgate
X Pull the tailgate down using one of
recesses :.
X Push the tailgate closed from outside the
vehicle.
X Lock the vehicle if necessary with the & button on the key or with KEYLESS-GO (Y page 75).
Automatic opening and closing from the outside Important safety guidelines G Warning! Make sure the tailgate is closed when the engine is running and while driving. Among other dangers, deadly carbon monoxide (CO) gases may enter vehicle interior resulting in unconsciousness and death.
! The tailgate swings upwards and to the rear when opened. Therefore, make sure that there is sufficient clearance above and behind the tailgate.
To open the tailgate completely, a minimum clearance of 7.20 ft (2.20 m) above the ground is necessary.
Opening You can open the tailgate automatically with the key or the handle in the tailgate. X Press and hold the F button on the key
until the tailgate opens.
or X When the tailgate is unlocked, pull the handle and let it go again immediately.
Closing G Warning! Monitor the closing procedure carefully to make sure no one is in danger of being
injured. To prevent possible personal injury, always keep hands and fingers away from the cargo compartment opening when closing the tailgate. Be especially careful when small children are around. To stop the closing procedure, do one of the following: RPress or pull the remote tailgate opening/
closing switch on the driver’s door.
RPress the tailgate closing switch. RPress the KEYLESS-GO locking/closing
switch.
RPull outside handle on the tailgate. RWhen no SmartKey is inserted in the starter switch (vehicles with KEYLESS-GO: Make sure the vehicle’s on-board electronics have status 0): Press button F on the SmartKey.
You can close the tailgate automatically using the key, the closing button6 or the locking button7.
X To close: press closing button : on the
tailgate.
or X Press and hold the F button on the key
until the tailgate closes.
X To close and lock simultaneously:
Press locking button ; on the tailgate.
i The tailgate can only be opened and
closed with the key if there is no key in the ignition lock.
6 For vehicles with the EASY-PACK tailgate only. 7 For vehicles with the EASY-PACK tailgate and KEYLESS-GO only.
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 85
Version: 3.0.3.5
Tailgate
85
If the tailgate touches an object while closing, the closing procedure is interrupted and the tailgate reopens.
i Only with KEYLESS-GO: if you leave a
KEYLESS-GO key in the cargo compartment, the tailgate will not lock. The tailgate is not closed unless a KEYLESS-GO key is detected.
Opening the tailgate from the inside G Warning! Do not leave children unattended in the vehicle. Children could open the tailgate from the inside, which could result in an accident and/or serious personal injury.
! Always make sure there is sufficient
space when opening.
You can unlock and open the tailgate from inside the vehicle. The handle is on the lower part of the tailgate window on the right-hand side when viewed in the direction of travel.
X Press handle : in the direction of
arrow ; as far as it will go and hold it there.
X From this position, pull handle : in the
direction of arrow = as far as it will go and hold it there.
X Swing the tailgate upwards. i Vehicles with the EASY-PACK tailgate:
If you do not open the tailgate after unlocking, it will lock again automatically after a few seconds.
Automatic opening and closing from the inside You can open and close the tailgate from the driver's seat when the vehicle is stationary. G Warning! Maintain sight of the area around the rear of the vehicle while operating the tailgate with the door-mounted remote tailgate switch. Monitor the closing procedure carefully to make sure no one is in danger of being injured. To interrupt the closing procedure, press or pull the door-mounted remote tailgate switch. G Warning! To prevent possible personal injury, always keep hands and fingers away from the cargo compartment opening when closing the tailgate. Be especially careful when small children are around. G Warning! Make sure the tailgate is closed when the engine is running and while driving. Among other dangers, deadly carbon monoxide (CO) gases may enter vehicle interior resulting in unconsciousness and death. G Warning! Maintain sight of the area around the rear of the vehicle while operating the tailgate with the door-mounted remote tailgate switch. Monitor the opening procedure carefully to make sure no one is in danger of being injured. To interrupt the opening procedure, press or pull the door-mounted remote tailgate switch. When the SmartKey is not inserted in the starter switch (vehicles with KEYLESS-GO: Make sure the vehicle’s on-board electronics
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 86
Version: 3.0.3.5
86
Side windows
have status 0): Press button F on the SmartKey.
X To open: pull remote operating switch :
for the tailgate until the tailgate opens.
X To close: turn the SmartKey to position 1
or 2 in the ignition lock.
X Press remote operating switch for
tailgate : until the tailgate is closed.
If the tailgate touches an object while closing, the closing procedure is interrupted and the tailgate reopens. X To interrupt the closing procedure: pull
or push the remote operating switch for tailgate :.
Limiting the opening angle of the tailgate Important safety guidelines You can limit the opening angle of the tailgate in the top half of its opening range. This could be useful, for example, if there is insufficient space above the tailgate. ! Make sure there is sufficient clearance to
open the tailgate fully when setting the opening angle. The tailgate could otherwise be damaged. Ideally, set the opening angle outside.
Activating the tailgate X To open the tailgate: pull the handle on
the tailgate.
X To stop the opening procedure at the desired position: press the close button (Y page 84) on the tailgate or pull the handle on the outside of the tailgate again. X To store the position: press and hold the closing button on the tailgate until you hear a short tone. The opening angle limiter is activated. The tailgate will now stop in the stored position when opening.
Deactivating the tailgate X Press and hold the closing button
(Y page 84) in the tailgate until you hear two short tones.
Side windows Important safety guidelines G Warning! When leaving the vehicle, always remove the SmartKey from the starter switch. Always take the SmartKey with you and lock the vehicle. Do not leave children unattended in the vehicle, even if they are secured in a child restraint system, or with access to an unlocked vehicle. A child's unsupervised access to a vehicle could result in an accident and/or serious personal injury. The children could Rinjure themselves on parts of the vehicle Rbe seriously or fatally injured through
excessive exposure to extreme heat or cold Rinjure themselves or cause an accident with
vehicle equipment that can be operated even if the SmartKey is removed from the starter switch or removed from the vehicle, such as seat adjustment, steering wheel adjustment, or the memory function
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 87
Version: 3.0.3.5
Side windows
87
If children open a door, they could injure other persons or get out of the vehicle and injure themselves or be injured by following traffic. Do not expose the child restraint system to direct sunlight. The child restraint system's metal parts, for example, could become very hot, and the child could be burned by these parts. G Warning! Do not carry heavy or hard objects in the passenger or cargo compartment unless they are firmly secured in place. Unsecured or improperly positioned cargo increases a child’s risk of injury in the event of Rstrong braking maneuvers Rsudden changes of direction Ran accident G Warning! When opening or closing the windows, make sure there is no danger of anyone being harmed by the opening/closing procedure. The door windows are equipped with the express operation and automatic reversal function. If in express operation mode a door window encounters an obstruction that blocks its path, the automatic reversal function will stop the door window and open it slightly. The door windows operate differently when the switch is pulled and held. See the "Closing when a door window is blocked" section in this chapter for details. The closing of a door window can be immediately halted by releasing the switch or, if the switch was pulled past the resistance point and released, by either pressing or pulling the respective switch. The closing of the hinged quarter windows can be immediately halted by pressing or pulling the switch. If a window encounters an obstruction that blocks its path in a circumstance where you
are closing the windows by pressing and holding button & on the SmartKey or by pressing and holding the lock button (vehicles with KEYLESS-GO) on an outside door handle, the automatic reversal function will not operate. Activate the override switch when children are riding in the back seats of the vehicle. The children may otherwise injure themselves, e.g. by becoming trapped in the window opening. G Warning! Do not keep any part of your body up against the window pane when opening a window. The downward motion of the pane may pull that part of your body down between the window pane and the door frame and trap it there. If there is a risk of entrapment, release the switch and pull it to close the window.
Opening and closing the side windows
: Front left ; Front right = Rear right ? Rear left The switches for all side windows are located on the driver's door. There is also a switch on each door for the corresponding side window. i Operation of the side windows in the rear
compartment is not possible when the
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 88
Version: 3.0.3.5
88
Side windows
override switch for the side windows is activated.
X Turn the key to position 2 in the ignition
lock.
i You can continue to operate the side
windows after you switch off the engine. This function remains active for five minutes or until one of the front doors is opened.
X To open: press the corresponding switch. X To close: pull the corresponding switch. i If you press the switch beyond the point
of resistance, an automatic opening/ closing process is started in the corresponding direction. You can stop automatic operation by pressing again.
Opening and closing the hinged side windows You can operate the hinged side windows electrically. The hinged side windows can only be operated from the driver's seat. G Warning! Make sure that nobody can become trapped as you close the hinged side windows. If there is a risk of somebody becoming trapped, release the switch or push the switch again to reopen the side window.
Door control panel
X Make sure that the key is in position 2 in
the ignition lock.
X To open: press switch : and release. Both hinged side windows open fully. X To close: pull switch : and release. Both hinged side windows close fully. X To stop the closing procedure: press
switch : again. The hinged side window opens fully.
i If the hinged side windows are blocked
when closing, the closing procedure is interrupted and the hinged side windows open again slightly.
i For safety reasons, the hinged side
windows can only be opened again after four seconds.
Resetting the side windows You must reset each side window if: Rthe battery has been disconnected or has
become discharged.
Rthe side window can no longer be fully
opened or closed. X Close all the doors. X Turn the key to position 2 in the ignition
lock.
X Pull on the corresponding switch on the
door control panel until the side window is completely closed (Y page 87).
X Hold the switch for an additional second. If the side window opens again slightly: X Pull the corresponding switch again
immediately and hold it for approximately one second.
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 89
Version: 3.0.3.5
Side windows
89
Convenience opening You can ventilate the vehicle before you start driving. To do this, you can use the key to simultaneously: Ropen the side windows Ropen the hinged side windows Ropen the tilt/sliding sunroof or the
panorama roof with power tilt/sliding panel and the roller sunblinds
i The convenience opening feature can only be operated using the key. The key must be near the handle of the driver's door.
X Point the tip of the key at the driver's door
handle.
X Press and hold the % button until the side windows and the tilt/sliding sunroof or panorama roof with power tilt/sliding panel are in the desired position. The vehicle is unlocked.
If the roller sunblinds of the panorama roof with power tilt/sliding panel are closed, the roller sunblinds are opened first. X Press and hold the % button again until the panorama roof with power tilt/sliding panel is in the desired position.
X To interrupt the convenience opening
procedure: release the % button.
Convenience closing General notes When you lock the vehicle, you can simultaneously: Rclose the side windows Rclose the hinged side windows Rclose the tilt/sliding sunroof or the
panorama roof with power tilt/sliding panel
On vehicles with a panorama roof with power tilt/sliding panel, you can then close the roller sunblinds.
G Warning! When closing the windows and the tilt/sliding sunroof or panorama roof with power tilt/ sliding panel, make sure there is no danger of anyone being harmed by the closing procedure. If potential danger exists, proceed as follows: RRelease button & to stop the closing
procedure. To open, press and hold button %. To continue the closing procedure after making sure that there is no danger of anyone being harmed by the closing procedure, press and hold button &.
Vehicles with KEYLESS-GO: RRelease the lock button on the outside door
handle to stop the closing procedure.
RImmediately pull on the same outside door
handle and hold firmly. The windows and the tilt/sliding sunroof or panorama roof with power tilt/sliding panel will open for as long as the door handle is held but the door not opened.
Using the SmartKey i The key must be near the handle of the
driver's door.
X Point the tip of the key at the driver's door
handle.
X Press and hold the & button until the side windows and the tilt/sliding sunroof or the panorama roof with power tilt/ sliding panel are fully closed.
X Make sure that all the side windows and the tilt/sliding sunroof or panorama roof with power tilt/sliding panel are closed.
On vehicles with a panorama roof with power tilt/sliding panel: X Press and hold the & button again until the roller sunblinds of the panorama roof with power tilt/sliding panel close.
X To interrupt the convenience closing
procedure: release the & button.
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 90
Version: 3.0.3.5
90
Side windows
Using KEYLESS-GO The SmartKey with KEYLESS-GO must be outside the vehicle but no more than 3 ft (1 m) away from a door. X Close all the doors.
X Keep locking button : on the door handle pressed until the side windows and the tilt/ sliding sunroof or panorama roof with power tilt/sliding panel are fully closed.
X Make sure that all the side windows and the tilt/sliding sunroof or panorama roof with power tilt/sliding panel are closed.
On vehicles with a panorama roof with power tilt/sliding panel: X Press and hold locking button : again
until the roller sunblinds of the panorama roof with power tilt/sliding panel close.
X To interrupt convenience closing: release locking button : on the door handle.
Problems with the side windows Problem: a side window cannot be closed because objects are trapped between the side window and the door frame. X Remove the objects. X Close the side window.
Problem: a side window cannot be closed because objects in the guide rail are preventing the window from being raised. X Remove the objects. X Close the side window. Problem: a side window cannot be closed, and you cannot see the cause. G Warning! Closing the side windows with increased force or without the anti-entrapment feature could lead to serious or even fatal injury. Make sure that nobody can become trapped when closing the side windows.
If a side window is obstructed during closing and reopens again slightly: X Immediately after the window blocks, pull on the corresponding switch again until the side window has closed. The side window is closed with increased force.
If a side window is obstructed again during closing and reopens again slightly: X Immediately after the window blocks, pull on the corresponding switch again until the side window has closed. The side window is closed without the anti- entrapment feature. G Warning! Pulling and holding the switch to close the door window immediately after it had been blocked two times will cause the door window to close without the anti-entrapment feature for as long as you hold the switch.
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 91
Version: 3.0.3.5
Sliding sunroof
91
Sliding sunroof Important safety guidelines G Warning! When leaving the vehicle, always remove the SmartKey from the starter switch. Always take the SmartKey with you and lock the vehicle. Do not leave children unattended in the vehicle, even if they are secured in a child restraint system, or with access to an unlocked vehicle. A child's unsupervised access to a vehicle could result in an accident and/or serious personal injury. The children could Rinjure themselves on parts of the vehicle Rbe seriously or fatally injured through
excessive exposure to extreme heat or cold Rinjure themselves or cause an accident with
vehicle equipment that can be operated even if the SmartKey is removed from the starter switch or removed from the vehicle, such as seat adjustment, steering wheel adjustment, or the memory function
If children open a door, they could injure other persons or get out of the vehicle and injure themselves or be injured by following traffic. Do not expose the child restraint system to direct sunlight. The child restraint system's metal parts, for example, could become very hot, and the child could be burned by these parts. G Warning! Do not carry heavy or hard objects in the passenger or cargo compartment unless they are firmly secured in place. Unsecured or improperly positioned cargo increases a child’s risk of injury in the event of Rstrong braking maneuvers Rsudden changes of direction Ran accident
G Warning! When opening or closing the tilt/sliding sunroof, make sure there is no danger of anyone being harmed by the opening/closing procedure. The tilt/sliding sunroof is equipped with the automatic operation and anti-entrapment features. If the movement of the tilt/sliding sunroof is blocked during the closing procedure, the tilt/sliding sunroof will stop and open slightly. The tilt/sliding sunroof operates differently when the sunroof switch is pressed and held. See the "Closing when the tilt/sliding sunroof is blocked" section for details. The opening/closing procedure of the tilt/ sliding sunroof can be immediately halted by releasing the sunroof switch or, if the sunroof switch was moved past the resistance point and released, by moving the sunroof switch in any direction. G Warning! The tilt/sliding sunroof is made out of glass. In the event of an accident, the glass may shatter. This may result in an opening in the roof. In a vehicle rollover, occupants not wearing their seat belts or not wearing them properly may be thrown out of the opening. Such an opening also presents a potential for injury for occupants wearing their seat belts properly as entire body parts or portions of them may protrude from the passenger compartment. G Warning! When opening or closing the tilt/sliding panel, make sure there is no danger of anyone being harmed by the opening/closing procedure. The tilt/sliding panel is equipped with the automatic operation and anti-entrapment features. If the movement of the tilt/sliding panel is blocked during the closing procedure, the tilt/sliding panel will stop and open slightly.
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 92
Version: 3.0.3.5
92
Sliding sunroof
The tilt/sliding panel operates differently when the roof panel switch is pressed and held. See the relevant section in this chapter for details. The opening/closing procedure of the tilt/ sliding panel can be immediately halted by releasing the roof panel switch or, if the roof panel switch was moved past the resistance point and released, by moving the roof panel switch in any direction. G Warning! The panorama roof with tilt/sliding panel is made out of glass. In the event of an accident, the glass may shatter. This may result in an opening in the roof. In a vehicle rollover, occupants not wearing their seat belts or not wearing them properly may be thrown out of the opening. Such an opening also presents a potential for injury for occupants wearing their seat belts properly as entire body parts or portions of them may protrude from the passenger compartment.
! Only open the sliding sunroof if it is free of snow and ice. Otherwise, malfunctions may occur. Do not allow anything to protrude from the sliding sunroof. Otherwise, the seals could be damaged.
! If the sliding sunroof cannot be opened or
closed due to a malfunction, contact a qualified specialist workshop, e.g. an authorized Mercedes-Benz Center.
! Do not forget that the weather can
change abruptly. Make certain that the sliding sunroof is closed when you leave the vehicle. The vehicle electronics can be damaged if water enters the vehicle interior.
i Resonance noises can occur in addition to the usual airflow noises when the sliding sunroof is open. They are caused by minor pressure fluctuations in the vehicle interior. Change the position of the sliding sunroof
or open a side window slightly to reduce or eliminate these noises.
Operating the sliding sunroof Opening and closing i You can still operate the tilt/sliding
sunroof even if you switch off the engine or remove the SmartKey. This function remains active for five minutes or until one of the front doors is opened.
Overhead control panel : To raise ; To open = To close X Switch on the ignition. X Push or pull the 2 switch in the
corresponding direction.
i If you press the 2 switch beyond the point of resistance, an automatic opening/ closing process is started in the corresponding direction. You can stop automatic operation by pressing again. Automatic opening/raising is only available if the tilt/sliding sunroof is in the closed position.
You can open/close the cover for the sunblind manually when the tilt/sliding sunroof is raised/closed.
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 93
Version: 3.0.3.5
Resetting Reset the tilt/sliding sunroof if it does not open smoothly, or if the battery has been disconnected or has become discharged. ! Contact a qualified specialist workshop if
the tilt/sliding sunroof cannot be closed fully or reset.
X Remove the SmartKey from the ignition lock or turn to position 0 (KEYLESS-GO).
X Remove the fuse for the tilt/sliding sunroof from the main fuse box. To find out where the fuse is located, refer to the fuse allocation chart in the vehicle tool kit (Y page 294).
X Reinsert the fuse. X Switch on the ignition. X Raise the tilt/sliding sunroof fully at the
rear (Y page 92).
X Keep the 2 switch pressed for another
second.
X Make sure that the tilt/sliding sunroof can be opened or closed fully again using the opening/closing process (Y page 92).
X If the tilt/sliding sunroof can be raised fully at the rear it is set correctly. If this is not the case, you must repeat the previously described steps.
Sliding sunroof
93
Operating the panorama sliding sunroof Opening and closing
Overhead control panel : To raise ; To open = To close The panorama roof with power tilt/sliding panel can only be moved when the roller sunblinds are open. X Turn the key to position 2 in the ignition
lock.
X Push or pull the 2 switch in the
corresponding direction.
i When opening the panorama roof with
power tilt/sliding panel, you can initiate the automatic opening process. To do so, press the 2 switch briefly beyond the point of resistance in the direction of arrow ;. By pressing again, the automatic opening process can be stopped. Automatic raising is only available if the panorama sliding sunroof is in the closed position.
Operating the roller sunblinds of the panorama sliding sunroof General notes The roller sunblinds provide protection from the sun. The two roller sunblinds can only be opened and closed together when the
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 94
Version: 3.0.3.5
94
Sliding sunroof
panorama roof with power tilt/sliding panel is closed. G Warning! When extending the roller sunblinds, make sure no one is in danger of being injured by the extending procedure. The extending of the roller sunblinds can be immediately halted by releasing the switch.
Opening and closing
Overhead control panel : To open ; To open = To close X Turn the key to position 2 in the ignition
lock.
X Push or pull the 2 switch in the
corresponding direction.
i When opening the roller sunblinds, you
can initiate an automatic opening process. To do so, press the 2 switch briefly beyond the point of resistance in the direction of arrow ;. By pressing again, the automatic opening process can be stopped.
Resetting the panorama roof with power tilt/sliding panel and the roller sunblinds Reset the panorama roof with power tilt/ sliding panel and the roller sunblinds if the panorama roof with power tilt/sliding panel
does not open smoothly, or if the battery has been disconnected or discharged. ! Do not open the panorama sliding sunroof until it has been reset properly. Otherwise, the panorama roof with power tilt/sliding panel may lock in the open position. If the panorama roof with power tilt/sliding panel cannot be closed or adjusted, contact a qualified specialist workshop, e.g. a Mercedes-Benz Service Center.
X Remove the SmartKey from the ignition lock or turn to position 0 (KEYLESS-GO). X Remove the fuse for the panorama roof
with power tilt/sliding panel from the fuse box. To find out where the fuse is located, refer to the fuse allocation chart in the vehicle tool kit (Y page 294).
X Reinsert the fuse. X Turn the key to position 2 in the ignition
lock.
X Close the roller sunblinds fully
X Keep the 2 switch pressed for another
(Y page 94).
second.
X Open the roller sunblinds fully (Y page 94). X Keep the 2 switch pulled for an
additional second.
X Close the panorama roof with power tilt/
sliding panel fully (Y page 93).
X Keep the 2 switch pressed for another
second.
X Make sure that the panorama roof with
power tilt/sliding panel can be opened fully again (Y page 93).
X If this is not the case, repeat the previously
described steps.
Problems with the sliding sunroof/ panorama sliding sunroof Problem: the sunroof cannot be closed and you cannot see the cause.
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 95
Version: 3.0.3.5
Sliding sunroof
95
G Warning! You could be severely or even fatally injured when closing the sliding sunroof with increased closing force or if the anti- entrapment feature is deactivated. Make sure that nobody can become trapped when closing the sliding sunroof.
If the sliding sunroof is obstructed during closing: X Immediately after the sliding sunroof
blocks, pull the 2 switch in the overhead control panel down to the point of resistance and hold it until the sliding sunroof is closed. The sliding sunroof is closed with increased force.
If the sliding sunroof is obstructed during closing again: X Immediately after the sliding sunroof
blocks, pull the 2 switch in the overhead control panel down to the point of resistance and hold it until the sliding sunroof is closed. The sliding sunroof is closed without the anti-entrapment feature. G Warning! Pressing and holding the sliding sunroof switch to close the sliding sunroof immediately after it had been blocked two times will cause the sliding sunroof to close without the anti-entrapment feature for as long as you hold the switch.
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 96
Version: 3.0.3.5
96
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 97
Version: 3.0.3.5
Vehicle equipment .............................. 98
Correct driver's seat position ............ 98
Seats .................................................... 99
Steering wheel .................................. 109
Mirrors ............................................... 111
Memory functions ............................. 114
97
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 98
Version: 3.0.3.5
98
Correct driver's seat position
Vehicle equipment
i This manual describes all the standard and optional equipment of your vehicle which was available at the time of purchase. Country-specific differences are possible. Bear in mind that your vehicle may not feature all functions described here. This also refers to safety-related systems and functions.
Correct driver's seat position
Observe the important safety notes on (Y page 99). X Check whether you have adjusted seat =
properly. Electrical seat adjustment (Y page 100) When adjusting the seat, make sure: Ryou are as far away from the driver's air
bag as possible.
Ryou are sitting in a normal upright
position.
Ryou can fasten the seat belt properly. Ryou have moved the backrest to an
almost vertical position.
Ryou have set the seat cushion angle so that your thighs are gently supported. Ryou can depress the pedals properly.
X Check whether the head restraint is
adjusted properly (Y page 101). When doing so, make sure that you have adjusted the head restraint so that the back of your head is supported at eye level by the center of the head restraint.
Observe the important safety notes on (Y page 109). X Check whether steering wheel : is
adjusted properly. Adjusting the steering wheel manually(Y page 109) Adjusting the steering wheel electrically (Y page 110) When adjusting the steering wheel, make sure: Ryou can hold the steering wheel with your
arms slightly bent.
Ryou can move your legs freely. Ryou can see all the displays in the
instrument cluster clearly.
Observe the important safety notes on (Y page 54). X Check whether you have fastened seat
belt ; properly (Y page 55). The seat belt should: Rfit snugly across your body Rbe routed across the middle of your
shoulder
Rbe routed in your pelvic area across the
hip joints
X Before starting off, adjust the rear-view
mirror and the exterior mirrors (Y page 112) in such a way that you have a good view of road and traffic conditions. X Vehicles with memory function: save the
seat, steering wheel and exterior mirror settings (Y page 114).
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 99
Version: 3.0.3.5
Seats
99
Seats Important safety guidelines G Warning In order to avoid possible loss of vehicle control, all seat, head restraint, steering wheel and rear view mirror adjustments, as well as fastening of seat belts, must be done before setting the vehicle in motion. G Warning Do not adjust the driver's seat while driving. Adjusting the seat while driving could cause the driver to lose control of the vehicle. Never travel in a moving vehicle with the seat backrest in an excessively reclined position as this can be dangerous. You could slide under the seat belt in a collision. If you slide under it, the seat belt would apply force at the abdomen or neck. This could cause serious or fatal injuries. The seat backrest and seat belts provide the best restraint when the wearer is in a position that is as upright as possible and seat belts are properly positioned on the body. G Warning Your seat belt must be adjusted so that you can correctly fasten your seat belt. Observe the following points: Radjust the seat backrest until your arms are
slightly angled when holding the steering wheel.
Radjust the seat to a comfortable seating position that still allows you to reach the accelerator/brake pedal safely. The position should be as far back as possible with the driver still able to operate the controls properly.
Radjust the head restraint so that it is as
close to the head as possible and the center
of the head restraint supports the back of the head at eye level.
Rnever place hands under the seat or near
any moving parts while a seat is being adjusted.
Failure to do so could result in an accident and/or serious personal injury. G Warning The electrically adjustable seats can be operated at any time. Therefore, do not leave children unattended in the vehicle, or with access to an unlocked vehicle. A child's unsupervised access to a vehicle could result in an accident and/or serious personal injury. G Warning! According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating position. Thus, we strongly recommend that children be placed in the rear seats whenever possible. Regardless of seating position, children 12 years old and under must be seated and properly secured in an appropriately sized infant restraint, toddler restraint, or booster seat recommended for the size and weight of the child. For additional information, see "Children in the vehicle". A child's risk of serious or fatal injuries is significantly increased if the child restraints are not properly secured in the vehicle and/ or the child is not properly secured in the child restraint. G Warning For your protection, drive only with properly positioned head restraints. Adjust the head restraint so that it is as close to the head as possible and the center of the head restraint supports the back of the head at eye level. This will reduce the potential for injury to the head and neck in the event of an accident or similar situation.
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 100
Version: 3.0.3.5
100 Seats
Do not drive the vehicle without the seat head restraints. Head restraints are intended to help reduce injuries during an accident.
To avoid damage to the seats and the seat heating, observe the following information: Rdo not spill any liquids on the seats. If
liquid is spilled on the seats, dry them as soon as possible.
Rif the seat covers are damp or wet, do not
switch on the seat heating. The seat heating should also not to be used to dry the seats.
Rclean the seat covers as recommended;
see the " Interior care" section.
Rdo not transport heavy loads on the
seats. Do not place sharp objects on the seat cushions, e.g. knives, nails or tools. The seats should only be occupied by passengers, if possible.
Rwhen the seat heating is in operation, do
not cover the seats with insulating materials, e.g. covers, bags, seat covers, child seats or booster seats.
! When you move the seats, make sure that
there are no objects in the footwell or behind the seats. Otherwise, you could damage the seats and the objects.
! When the outer seats in the second row are folded down, the front seats must not be in their rearmost position. The front seats and the outer seats in the second row could otherwise be damaged.
! Make sure that the sun visor is folded up
before adjusting the backrest and head restraint height. The head restraint and sun visor could otherwise collide when the head restraint is fully extended.
i The rear-compartment head restraints
can be removed (Y page 102). Please contact an authorized Mercedes- Benz Center for more information.
8 Only for vehicles with the memory function.
i Related topics:
RCargo compartment enlargement
(folding the second and third rows of seats forwards) (Y page 250)
Adjusting the seats i Vehicles without the memory function:
the seats can be adjusted within five minutes of opening a front door. The time span starts over if, within these five minutes, you: Ropen or close a front door Rinsert the key into or remove the key
from the ignition lock
Rswitch the ignition on or off. If the key is in position 2 in the ignition, you can adjust the seats at any time.
: Head restraint height8
; Backrest angle
= Seat fore-and-aft adjustment
? Seat cushion angle
A Seat height
i Vehicles with the memory function: if
PRE-SAFE® is triggered, the front- passenger seat will be moved to a better position if it was previously in an unfavorable position.
i You can store the seat settings using the
memory function (Y page 114).
BA 251 USA, CA Edition A 2011; 1; 3, en-US d2sboike
2010-04-16T14:31:55+02:00 - Seite 101
Version: 3.0.3.5
Seats
101
Adjusting the head restraints Adjusting the head restraints manually
Adjusting the head restraint height9
! The head restraints may only be removed
in a qualified specialist workshop. Mercedes-Benz recommends that you go to an authorized Mercedes-Benz Center.
X If the head restraint is fully lowered, it is
necessary to press release catch :.
X To raise: pull the head restraint up to the
desired position.
X To lower: press release catch : in the direction of the arrow and push the head restraint down to the desired position.
X Push or pull the lower edge of the head restraint in the direction of the arrow.
Adjusting the head restraint height
electrically10
X To adjust the head restraint height: slide
the switch for head restraint adjustment (Y page 100) up or down in the direction of the arrow.