2007 Mercedes-benz E Class Owners Manual

1 To release the mobile phone cradle 2 To remove the mobile phone cradle 3 Mobile phone cradle 왘 Press release button in direction of

arrow 1 and take mobile phone cradle 3 out in direction of arrow 2.

293

Controls in detail Useful features

Installing a different mobile phone cradle

Tele Aid

! The initial activation of the Tele Aid system may only be performed by completing the sub- scriber agreement and placing an acquaintance call using button ¡. Failure to complete ei- ther of these steps will result in a system that is not activated. If you have any questions regarding activation, please call the Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada).

Shortly after the completion of your Tele Aid acquaintance call, you will receive a user ID and password. By visiting www.mbusa.com and selecting “Tele Aid” (USA only), you will have access to account information, remote door unlock and more.

Example illustration 1 Contact plate 2 Recesses 3 Mobile phone cradle 왘 Insert mobile phone cradle 3 into

recesses 2 of contact plate 1.

왘 Push mobile phone cradle 3 forward

until it engages.

294

The Tele Aid system (Telematic Alarm Identification on De- mand) The Tele Aid system consists of three types of response: 앫 automatic and manual emergency 앫 Roadside Assistance and 앫 information The Tele Aid system is operational provid- ing that the vehicle’s battery is charged, properly connected, not damaged and cel- lular and GPS coverage is available. The speaker volume of a Tele Aid call can be adjusted when using the volume control on the multifunction steering wheel. To raise, press button æ and to lower, press button ç or use the volume knob on your COMAND headunit. 왘 To activate, press the SOS button, the

Roadside Assistance button • or the Information button ¡, depend- ing on the type of response required.

Warning!

If the indicator lamps in the SOS button, in the Roadside Assistance button and/or in the Information button remain illuminated constantly in red and/or the message Tele Aid malfunction Drive to workshop is displayed in the multifunction display after the system self-check, a mal- function in the system has been detected.

If a malfunction is indicated as outlined above, the system may not operate as ex- pected. Have the system checked at the nearest Mercedes-Benz Center as soon as possible.

i The SOS button is located above the interior rear view mirror (컄 page 297). The Roadside Assistance button • and the Information button ¡ are located below the center armrest cover (컄 page 285).

i The Tele Aid system utilizes the cellular net- work for communication and the GPS (Global Po- sitioning System) satellites for vehicle location. If either of these signals are unavailable, the Tele Aid system may not function and if this oc- curs, assistance must be summoned by other means.

System self-check Initially, after switching on the ignition, malfunctions are detected and indicated (the indicator lamps in the SOS button, the Roadside Assistance button • and the Information button ¡ stay on longer than 10 seconds or do not come on). The message Tele Aid malfunction Drive to workshop appears in the multi- function display.

Controls in detail Useful features

Emergency calls An emergency call is initiated automatical- ly following an accident in which the emer- gency tensioning devices (ETDs) or air bags deploy. An emergency call can also be initiated manually by opening the cover next to the interior rear view mirror labeled SOS, then briefly pressing the button located under the cover. See (컄 page 297) for instruc- tions on initiating an emergency call man- ually. Once the emergency call is in progress, the indicator lamp in the SOS button will begin to flash. The message Connecting call appears in the multifunction display and the audio system is muted. When the con- nection is established, the message Call connected appears in the multifunc- tion display. All information relevant to the emergency, such as the location of the ve- hicle (determined by the GPS satellite loca- tion system), vehicle model, identification number and color are generated.

295

Controls in detail Useful features

A voice connection between the Response Center and the occupants of the vehicle will be established automatically soon af- ter the emergency call has been initiated. The Response Center will attempt to deter- mine more precisely the nature of the emergency provided they can speak to an occupant of the vehicle.

The Tele Aid system is available if 앫 it has been activated and is operation- al. Activation requires a subscription for monitoring services, connection and cellular air time

앫 the relevant cellular phone network

and GPS signals are available and pass the information on to the Response Center

i Location of the vehicle on a map is only pos- sible if the vehicle is able to receive signals from the GPS satellite network and pass the informa- tion on to the Response Center.

Warning!

If the indicator lamp in the SOS button is flashing continuously and there was no voice connection to the Response Center established, then the Tele Aid system could not initiate an emergency call (e.g. the rele- vant cellular phone network is not available). The message Call failed appears in the multifunction display for approximately 10 seconds.

Should this occur, assistance must be sum- moned by other means.

296

Warning!

If you feel at any way in jeopardy when in the vehicle (e.g. smoke or fire in the vehicle, ve- hicle in a dangerous road location), please do not wait for voice contact after you have pressed the emergency button. Carefully leave the vehicle and move to a safe loca- tion. The Response Center will automatically contact local emergency officials with the vehicle’s approximate location if they re- ceive an automatic SOS signal and cannot make voice contact with the vehicle occu- pants.

Initiating an emergency call manually

1 Cover 2 SOS button 왘 Briefly press on cover 1.

The cover will open.

왘 Press SOS button 2 briefly.

The indicator lamp in SOS button 2 will flash until the emergency call is concluded.

왘 Wait for a voice connection to the Re-

sponse Center.

왘 Close cover after the emergency call is

concluded.

Controls in detail Useful features

Roadside Assistance button • Located below the center armrest cover is the Roadside Assistance button •. 왘 Press and hold the button (for longer

than 2 seconds). A call to a Mercedes-Benz Roadside As- sistance dispatcher will be initiated. The button will flash while the call is in progress. The message Connecting call will appear in the multifunction display and the audio system is muted.

When the connection is established, the message Call connected appears in the multifunction display. The Tele Aid system will transmit data generating the vehicle identification number, model, color and lo- cation (subject to availability of cellular and GPS signals). A voice connection between the Roadside Assistance dispatcher and the occupants of the vehicle will be established. 왘 Describe the nature of the need for as-

sistance.

297

Controls in detail Useful features

The Mercedes-Benz Roadside Assistance dispatcher will either dispatch a qualified Mercedes-Benz technician or arrange to tow your vehicle to the nearest authorized Mercedes-Benz Center. For services such as labor and/or towing, charges may ap- ply. Refer to the Roadside Assistance man- ual for more information. The following is only available in the USA: 앫 Sign and Drive services: Services such as a jump start, a few gallons of fuel or the replacement of a flat tire with the vehicle spare tire are obtainable.

298

i The indicator lamp on the Roadside Assis- tance button • remains illuminated in red for approximately 10 seconds during the system self-check after switching on the ignition (togeth- er with the SOS button and the Information button ¡). See system self-check (컄 page 295) when the indicator lamp does not come on in red or stays on longer than approximately 10 seconds. If the indicator lamp on the Roadside Assistance button • is flashing continuously and there was no voice connection to the Response Center established, then the Tele Aid system could not initiate a Roadside Assistance call (e.g. the rele- vant cellular phone network is not available). The message Call failed appears in the multi- function display. Roadside Assistance calls can be terminated us- ing button t on the multifunction steering wheel or the respective button for ending a tele- phone call on the COMAND headunit.

Information button ¡ The Information button ¡ is located be- low the center armrest cover. 왘 Press and hold button (for longer than

2 seconds). A call to the Customer Assistance Cen- ter will be initiated. The button will flash while the call is in progress. The message Connecting call will appear in the multifunction display and the au- dio system is muted.

When the connection is established, the message Call connected appears in the multifunction display. The Tele Aid system will transmit data generating the vehicle identification number, model, color and lo- cation (subject to availability of cellular and GPS signals). A voice connection between the Customer Assistance Center representative and the occupants of the vehicle will be estab- lished. Information regarding the operation of your vehicle, the nearest authorized

Information calls can be terminated using button t on the multifunction steering wheel or the respective button for ending a telephone call on the COMAND headunit. ! If the indicator lamps do not start flashing after pressing one of the buttons or remain illu- minated (in red) at any time, the Tele Aid system has detected a malfunction or the service is not currently active, and may not initiate a call. Visit an authorized Mercedes-Benz Center and have the system checked or contact the Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada) as soon as possi- ble.

Mercedes-Benz Center or Mercedes-Benz USA products and services is available to you. For more details concerning the Tele Aid system, please visit www.mbusa.com and use your ID and password (sent to you sep- arately) to learn more (USA only).

i The indicator lamp on the Information button ¡ remains illuminated in red for ap- proximately 10 seconds during the system self-check after switching on the ignition (togeth- er with the SOS button and the Roadside Assis- tance button •). See system self-check (컄 page 295) when the indicator lamp does not come on in red or stays on longer than approximately 10 seconds. If the indicator lamp on the Information button ¡ is flashing continuously and there was no voice connection to the Response Center established, then the Tele Aid system could not initiate an Information call (e.g. the relevant cel- lular phone network is not available). The mes- sage Call failed appears in the multifunction display.

Controls in detail Useful features

Call priority If other service calls such as a Roadside Assistance call or Information call are active, an Emergency call is still possible. In this case, the Emergency call will take priority and override all other ac- tive calls.

i The indicator lamp in the respective button flashes until the call is concluded. Calls can only be terminated by a Response Center or Custom- er Assistance Center representative except Roadside Assistance and Information calls, which can also be terminated by pressing button t on the multifunction steering wheel or the respective button for ending a telephone call on the COMAND headunit.

! If the indicator lamp continues to flash or the system does not reset, contact the Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada), or Mercedes-Benz Customer Assistance at 1-800-FOR-MERCedes (1-800-367-6372) in the USA or Customer Ser- vice at 1-800-387-0100 in Canada.

299

Controls in detail Useful features

i When a Tele Aid call has been initiated, the COMAND system audio is muted and the select- ed mode (radio or CD) pauses. The optional cel- lular phone (if installed) switches off. If you must use this phone, the vehicle must be parked. Dis- connect the coiled cord and place the call. The COMAND navigation* system (if engaged) will continue to run. The multifunction display in the instrument cluster is available for use, and spo- ken commands are only available by pressing the RPT button on the COMAND unit. A pop-up win- dow will appear in the COMAND display to indi- cate that a Tele Aid call is in progress.

300

i The remote door unlock feature is available if the relevant cellular phone network is avail- able. The SOS button will flash and the message Call connected will appear in the multifunc- tion display to indicate receipt of the door unlock command. Once the vehicle is unlocked, a Response Center specialist will attempt to establish voice contact with the vehicle occupants. If the trunk recessed handle was pulled for more than 20 seconds before door unlock authoriza- tion was received by the Response Center, you must wait 15 minutes before pulling the trunk re- cessed handle again.

Remote door unlock In case you have locked your vehicle unin- tentionally (e.g. SmartKey inside vehicle), and the reserve SmartKey is not handy: 왘 Contact the Mercedes-Benz Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada). You will be asked to provide your pass- word which you provided when you completed the subscriber agreement. 왘 Then return to your vehicle and pull the trunk recessed handle for a minimum of 20 seconds until the SOS button is flashing. The message Call connected appears in the multifunction display.

As an alternative, you may unlock the vehi- cle via Internet using the ID and password sent to you shortly after the completion of your acquaintance call. The Response Center will then unlock your vehicle with the remote door unlocking feature.

Garage door opener

The integrated remote control is capable of operating up to three separately controlled devices. It provides a convenient way to re- place up to three hand-held remote con- trols used to operate devices such as garage door openers, gate openers, or oth- er devices compatible with HomeLink® or some other systems. Before the integrated remote control can be used, it must be programmed to the ga- rage door opener, gate operator or other device you wish to operate. See the follow- ing instructions for programming informa- tion.

Stolen Vehicle Recovery services In the event your vehicle was stolen: 왘 Report the incident to the police.

The police will issue a numbered inci- dent report.

왘 Pass this number on to the

Mercedes-Benz Response Center along with your password issued to you when you subscribed to the service. The Response Center will then attempt to covertly contact the vehicle’s Tele Aid system. Once the vehicle is locat- ed, the Response Center will contact the local law enforcement and you. The vehicle’s location will only be provided to law enforcement.

i When the anti-theft alarm stays on for more than 30 seconds, a call is initiated automatically to the Response Center. See anti-theft alarm system (컄 page 106).

Controls in detail Useful features

Indicator lamp

Interior rear view mirror with integrated re- mote control 2 3 4 Signal transmitter button Needed for programming (not part of vehi- cle equipment):

Hand-held remote control of ga- rage door opener, gate operator or other device Hand-held remote control but- ton

301

Controls in detail Useful features

Warning!

When programming a garage door opener, park vehicle outside the garage.

Do not run the engine while programming the integrated remote control. Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide (CO), and inhaling it can cause unconscious- ness and possible death.

Programming the integrated remote control Step 1: 왘 Switch on the ignition (컄 page 37).

Before programming the integrated remote control to a garage door opener or gate operator, make sure people and objects are out of the way of the device to prevent po- tential harm or damage. When programming a garage door opener, the door moves up or down. When programming a gate operator, the gate opens or closes.

Do not use the integrated remote control with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door that cannot detect an object - signaling the door to stop and reverse - does not meet current U.S. federal safety standards.

302

Step 2: 왘 If you have previously programmed a signal transmitter button and wish to retain its programming, proceed to step 3. If you are programming the integrated remote control for the first time, press and hold the two outer signal transmit- ter buttons 2 and 4 and release them only when the indicator lamp 1 begins to flash after approximately 20 seconds (do not hold the button for longer than 30 seconds). This proce- dure erases any previous settings for all three channels and initializes the memory. If you later wish to program a second and/or third hand-held transmitter to the remaining two signal transmitter buttons, do not repeat this step and be- gin directly with step 3.

Step 3: 왘 Hold the end of hand-held remote

control 5 of the device you wish to train approximately 2 to 5 in (5 to 12 cm) away from the signal transmitter button (2, 3 or 4) to be programmed, while keeping the indica- tor lamp 1 in view.

Step 4: 왘 Using both hands, simultaneously

press hand-held remote control button 6 and the desired signal trans- mitter button (2, 3 or 4). Do not release the buttons until step 5 is com- pleted. Indicator lamp 1 will flash, first slowly and then rapidly.

i Indicator lamp 1 flashes immediately the first time the signal transmitter button is pro- grammed. If this button has already been pro- grammed, the indicator lamp will only start flashing after 20 seconds.

Step 5: 왘 After indicator lamp 1 changes from a slow to a rapidly flashing light, release the hand-held remote control button and the signal transmitter button.

Step 6: 왘 Press and hold the just-trained signal transmitter button (2, 3 or 4) and observe the indicator lamp 1. If indicator lamp 1 stays on constantly, programming is complete and your device should activate when the respective signal transmitter button (2, 3 or 4) is pressed and re- leased.

i If indicator lamp 1 flashes rapidly for about 2 seconds and then turns to a constant light, continue with programming steps 8 through 12 as your garage door opener may be equipped with the “rolling code” feature.

Step 7: 왘 To program the remaining two signal transmitter buttons, repeat the steps above starting with step 3.

Controls in detail Useful features

Rolling code programming To train a garage door opener (or other rolling code devices) with the rolling code feature, follow these instructions after completing the “Programming” portion (steps 1 through 6) of this text. (A second person may make the following training procedures quicker and easier.) Step 8: 왘 Locate “training” button on the garage

door opener motor head unit. Exact location and color of the button may vary by garage door opener brand. Depending on manufacturer, the “training” button may also be referred to as “learn”or “smart” button. If there is difficulty locating the transmitting button, refer to the garage door opener Operator’s Manual.

컄컄

303

Controls in detail Useful features

컄컄

Step 9: 왘 Press the “training” button on the ga-

rage door opener motor head unit. The “training light” is activated.

You have 30 seconds to initiate the follow- ing two steps. Step 10: 왘 Return to the vehicle and firmly press, hold for 2 seconds and release the pro- grammed signal transmitter button (2, 3 or 4).

Step 11: 왘 Press, hold for 2 seconds and release same signal transmitter button a sec- ond time to complete the training pro- cess.

i Some garage door openers (or other rolling code equipped devices) may require you to press, hold for 2 seconds and release the same signal transmitter button a third time to com- plete the training process.

304

Step 4: 왘 Press and hold the signal transmitter button (2, 3 or 4). Do not release this button until it has been successful- ly trained.

왘 While still holding down the signal transmitter button (2, 3 or 4), “cycle” your hand-held remote control button 6 as follows: Press and hold button 6 for 2 seconds, then release it for 2 seconds, and again press and hold it for 2 seconds. Repeat this se- quence on the hand-held remote con- trol until the frequency signal has been learned. Upon successful training, indi- cator lamp 1 will flash slowly and then rapidly after several seconds.

왘 Proceed with programming step 5 and

step 6 to complete.

Step 12: 왘 Confirm the garage door operation by pressing the programmed signal trans- mitter button (2, 3 or 4).

Step 13: 왘 To program the remaining two signal transmitter buttons, repeat the steps above starting with step 3.

Gate operator/Canadian programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission which may not be long enough for the integrated signal transmitter to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. If you live in Canada or if you are having difficulties programming a gate operator (regardless of where you live) by using the programming procedures, replace step 4 with the following:

Controls in detail Useful features

i Upon completion of programming the inte- grated remote control, make sure you retain the hand-held remote control that came with the ga- rage door opener, gate operator or other device. You may need it for use in other vehicles, for fu- ture programming of an integrated remote con- trol, or simply for continued use as a hand-held remote control to operate the respective device in other situations.

Reprogramming a single signal trans- mitter button To program a device using a signal trans- mitter button previously trained, follow these steps: 왘 Switch on the ignition (컄 page 37). 왘 Press and hold the desired signal transmitter button (2, 3 or 4). Do not release the button.

왘 Indicator lamp 1 will begin to flash af- ter 20 seconds. Without releasing the signal transmitter button, proceed with programming starting with step 3.

Operation of integrated remote control 왘 Switch on the ignition (컄 page 37). 왘 Select and press the appropriate inte- grated signal transmitter button (2, 3 or 4) to activate the remote con- trolled device. The integrated remote control trans- mitter continues to send the signal as long as the button is pressed – up to 20 seconds.

Erasing the integrated remote control memory 왘 Switch on the ignition (컄 page 37). 왘 Simultaneously press and hold outer signal transmitter buttons 2 and 4, for approximately 20 seconds, until indicator lamp 1 flashes rapidly. Do not hold for longer than 30 seconds. The codes of all three channels are erased.

i If you sell your vehicle, erase the codes of all three channels.

Programming tips If you are having difficulty programming the integrated remote control, here are some helpful tips: 앫 Check the frequency of hand-held re- mote control 5 (typically located on the reverse side of the remote). The in- tegrated remote control is compatible with radio-frequency devices operating between 280-390 MHz.

앫 Put a new battery in hand-held remote control 5. This will increase the likeli- hood of the hand-held remote control sending a faster and more accurate sig- nal to the integrated remote control.

앫 While performing step 3, hold

hand-held remote control 5 at differ- ent lengths and angles from the signal transmitter button (2, 3 or 4) you are programming. Attempt varying an- gles at the distance of 2 to 5 inches (5 to 12 cm) away or the same angle at varying distances.

305

i USA only: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer-

ence, and

(2) this device must accept any interference re-

ceived, including interference that may cause undesired operation.

Any unauthorized modification to this device could void the user’s authority to operate the equipment.

i Canada only: This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference re-

ceived, including interference that may cause undesired operation of the device. Any unauthorized modification to this device could void the user’s authority to operate the equipment.

Controls in detail Useful features

앫 If another hand-held remote control is available for the same device, try the programming steps again using that other hand-held remote control. Make sure new batteries are in the hand-held remote control before beginning the procedure.

앫 Straighten the antenna wire from the

garage door opener assembly. This may help improve transmitting and/or receiving signals.

i Certain types of garage door openers are in- compatible with the integrated remote control. If you should experience further difficulties with programming the integrated remote control, contact an authorized Mercedes-Benz Center, or call Mercedes-Benz Customer Assistance Cen- ter (in the USA only) at 1-800-FOR-MERCedes, or Customer Service (in Canada) at 1-800-387-0100.

306

Operation

The first 1000 miles (1500 km) Driving instructions At the gas station Engine compartment Tires and wheels Winter driving Maintenance Vehicle care

307

Operation The first 1000 miles (1500 km)

In the “Operation” section you will find de- tailed information on operating, maintain- ing and caring for your vehicle.

308

After 1000 miles (1500 km) you may gradually increase vehicle and engine speeds to the permissible maximum.

! Additional instructions for AMG vehicles: 앫 During the first 1000 miles (1500 km), do not exceed a speed of 85 mph (140 km/h).

앫 During this period, avoid engine speeds

above 4500 rpm in each gear.

All of the above instructions, as may apply to your vehicle type, also apply when driv- ing the first 1000 miles (1500 km) after the engine or the rear differential has been replaced.

i Always obey applicable speed limits.

The more cautiously you treat your vehicle during the break-in period, the more satis- fied you will be with its performance later on. 앫 Drive your vehicle during the first

1000 miles (1500 km) at varying but moderate vehicle and engine speeds. 앫 During this period, avoid heavy loads (full throttle driving) and excessive en- gine speeds (no more than 2/3 of maximum rpm in each gear).

앫 Avoid accelerating by kickdown. 앫 Do not attempt to slow the vehicle

down by shifting to a lower gear using the gear selector lever.

앫 Select positions 3, 2 or 1 only when driving at moderate speeds (for hill driving).

앫 Select C as the preferred shift program (컄 page 190) for the first 1000 miles (1500 km).

Operation Driving instructions

Drinking and driving

Pedals

Warning!

Warning!

Make sure that absolutely no objects are ob- structing the pedals’ range of movement. Keep the driver’s footwell clear of all obsta- cles. If there are any floormats or carpets in the footwell, make sure that the pedals still have sufficient clearance.

Drinking and driving and/or taking drugs and driving are very dangerous combina- tions. Even a small amount of alcohol or drugs can affect your reflexes, perceptions and judgment.

The possibility of a serious or even fatal ac- cident are greatly increased when you drink or take drugs and drive.

Do not drink or take drugs and drive or allow anyone to drive who has been drinking or taking drugs.

왔 Driving instructions Drive sensibly – save fuel

Fuel consumption, to a great extent, de- pends on driving habits and operating con- ditions. To save fuel you should: 앫 Keep tires at the recommended infla-

tion pressures.

앫 Remove unnecessary loads. 앫 Remove roof rack when not in use. 앫 Allow engine to warm up under low

load use.

앫 Avoid frequent acceleration and decel-

eration.

앫 Have all maintenance work performed

at the intervals specified in the Maintenance Booklet and as required by the Maintenance System. Contact an authorized Mercedes-Benz Center.

Fuel consumption is also increased by driving in cold weather, in stop-and-go traffic, on short trips and in hilly area.

309

Operation Driving instructions

Power assistance

Brakes

Warning!

Warning!

With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the ve- hicle.

After driving in heavy rain for some time without applying the brakes or through wa- ter deep enough to wet brake components, the first braking action may be somewhat reduced and increased pedal pressure may be necessary to obtain expected braking ef- fect. Maintain a safe distance from vehicles in front.

Resting your foot on the brake pedal will cause excessive and premature wear of the brake pads.

It can also result in the brakes overheating, thereby significantly reducing their effec- tiveness. It may not be possible to stop the vehicle in sufficient time to avoid an acci- dent.

! Vehicles without 4MATIC: Because the ESP® operates automatically, the engine and the ignition must be shut off (SmartKey in starter switch position 0 or 1 or KEYLESS-GO start/stop button* in position 0 or 1) when: 앫 the parking brake is being tested on a brake

test dynamometer

앫 the vehicle is being towed with the front axle

raised

Active braking action through the ESP® may oth- erwise seriously damage the brake system. For information on vehicles with 4MATIC, see “Four wheel electronic traction system (4MATIC) with the ESP®” (컄 page 105). To help prevent brake disk corrosion after driving on wet road surfaces (particularly salted roads), it is advisable to brake the vehicle with considerable force prior to parking. The heat generated serves to dry the brakes.

310

If your brake system is normally only sub- jected to moderate loads, you should occa- sionally test the effectiveness of the brakes by applying above-normal braking pressure at higher speeds. This will also enhance the grip of the brake pads.

Warning!

Make sure not to endanger any other road users when carrying out these braking ma- neuvers.

Refer to the description of the Brake Assist System (BAS) (컄 page 99).

Brake pad wear or a leak in the system may be the reason for low brake fluid level in the reservoir. The brake fluid level in the reservoir may be too low if the brake warning lamp in the instrument cluster comes on and an acoustic warning sounds although the parking brake is released (컄 page 383). Observe additional messages in the multi- function display that may appear (컄 page 413). Have the brake system inspected immediately. Contact an authorized Mercedes-Benz Center. All checks and service work on the brake system should be carried out by qualified technicians only. Contact an authorized Mercedes-Benz Center. Only install brake pads and brake fluid recommended by Mercedes-Benz.

Operation Driving instructions

Warning!

If other than recommended brake pads are installed, or other than recommended brake fluid is used, the braking properties of the vehicle can be degraded to an extent that safe braking is substantially impaired. This could result in an accident.

! When driving down long and steep grades, relieve the load on the brakes by shifting into a lower gear to use the engine’s braking power. This helps prevent overheating of the brakes and reduces brake pad wear.

After hard braking, it is advisable to drive on for some time, rather than immediately park, so that the air stream will cool down the brakes faster.

311

Operation Driving instructions

High-performance brake system (E 63 AMG only) The high-performance brake system is de- signed to operate under the extremely high operating demands required to accommo- date the performance capabilities of the vehicle. The brakes may produce a squeak- ing-type noise depending on the 앫 vehicle speed 앫 brake force applied 앫 ambient conditions, e.g. temperature

and humidity

As with any brake system, the wear of indi- vidual brake system components such as brake pads or disks strongly depends on your driving style and the conditions under which you operate the vehicle. Thus, a driv- ing style calling for high demand braking will cause your vehicle’s brakes to wear more quickly.

312

Warning!

Driving off

New vehicle brake pads and discs, and replacement brake pads and discs may take several hundred miles of driving until they provide optimum braking efficiency. Until that time, you may need to use increased brake pedal pressure while braking. Please be aware of this and adjust your driving and braking accordingly during this break-in period.

Excessive high demand braking will cause correspondingly high brake wear. Please be attentive to the brake warning lamp in the instrument cluster and brake condition mes- sages in the multifunction display. Especial- ly for high performance driving, it is important to maintain and have the brake system checked regularly.

Apply the brakes to test them briefly after driving off. Perform this procedure only when the road is clear of other traffic. Warm up the engine smoothly. Do not place full load on the engine until the oper- ating temperature has been reached.

! When driving off on a slippery surface, do not allow a drive wheel to spin for an extended period with the ESP® switched off. Doing so may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty.

! Simultaneously depressing the accelerator pedal and applying the brake reduces engine performance and causes premature brake and drivetrain wear.

Parking

Warning!

Do not park this vehicle in areas where com- bustible materials such as grass, hay or leaves can come into contact with the hot exhaust system, as these materials could be ignited and cause a vehicle fire.

To reduce the risk of personal injury, or damage to the vehicle drivetrain, as a result of vehicle movement, before turning off the engine and leaving the vehicle always: 앫 Keep right foot on brake pedal. 앫 Firmly depress parking brake pedal.

앫 Move the gear selector lever to

position P.

앫 Slowly release brake pedal. 앫 When parked on an incline, turn front

wheel towards the road curb.

앫 Turn the SmartKey in the starter switch to position 0 and remove the SmartKey from the starter switch, or press KEYLESS-GO* start/stop button (vehi- cles with KEYLESS-GO*).

앫 Take the SmartKey or the SmartKey with KEYLESS-GO* with you and lock vehicle when leaving.

Operation Driving instructions

Tires

Warning!

If you feel a sudden significant vibration or ride disturbance, or you suspect that possi- ble damage to your vehicle has occurred, you should turn on the hazard warning flash- ers, carefully slow down, and drive with cau- tion to an area which is a safe distance from the road.

Inspect the tires and the vehicle underbody for possible damage. If the vehicle or tires appear unsafe, have the vehicle towed to the nearest Mercedes-Benz Center or tire dealer for repairs.

Treadwear indicators (TWI) are required by law. These indicators are located in six places on the tread circumference and be- come visible at a tread depth of approxi- mately 1/16 in (1.6 mm), at which point the tire is considered worn and should be re- placed.

313

Operation Driving instructions

The treadwear indicator appears as a solid band across the tread.

Warning!

Do not drive with a flat tire. A flat tire affects the ability to steer or brake the vehicle. You could lose control of the vehicle. Continued driving with a flat tire or driving at high speed with a flat tire will cause excessive heat build-up and possibly a fire.

For more information, see “Tires and wheels” (컄 page 333).

Hydroplaning

Depending on the depth of the water layer on the road, hydroplaning may occur, even at low speeds and with new tires. Reduce vehicle speed, avoid track grooves in the road and apply brakes cautiously in the rain.

Warning!

Although the applicable federal motor vehi- cle safety laws consider a tire to be worn when the treadwear indicators (TWI) be- come visible at approximately 1/16 in (1.6 mm), we recommend that you do not al- low your tires to wear down to that level. As tread depth approaches 1/8 in (3 mm), the adhesion properties on a wet road are sharply reduced.

Depending upon the weather and/or road surface (conditions), the tire traction varies widely.

Specified tire inflation pressures must be maintained. This applies particularly if the tires are subjected to high loads (e.g. high speeds, heavy loads, high ambient temper- atures).

314

Tire traction

The safe speed on a wet, snow covered or icy road is always lower than on a dry road. You should pay particular attention to the condition of the road whenever the outside temperatures are close to the freezing point.

Warning!

If ice has formed on the road, tire traction will be substantially reduced. Under such weather conditions, drive, steer and brake with extreme caution.

Mercedes-Benz recommends winter tires (컄 page 364) with a minimum tread depth of approximately 1/6 in (4 mm) on all four wheels for the winter season to make sure normal balanced handling characteristics. On packed snow, they can reduce your stopping distance compared to summer tires. Stopping distance, however, is still considerably greater than when the road is not covered with snow or ice. Exercise ap- propriate caution.

! Avoid spinning of a drive wheel. This may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty.

Tire speed rating

Regardless of the tire speed rating, local speed limits should be obeyed. Use pru- dent driving speeds appropriate to prevail- ing conditions.

Warning!

Even when permitted by law, never operate a vehicle at speeds greater than the maxi- mum speed rating of the tires.

Exceeding the maximum speed for which tires are rated can lead to sudden tire fail- ure, causing loss of vehicle control and pos- sibly resulting in an accident and/or personal injury and possible death, for you and for others.

Operation Driving instructions

An electronic speed limiter prevents your vehicle from exceeding a speed of: 앫 All models except E 63 AMG:

130 mph (210 km/h)

앫 E 63 AMG:

155 mph (250 km/h)

앫 E 63 AMG with increased top speed*

E 63 AMG (Performance Package*): 186 mph (300 km/h)

The factory equipped tires on your vehicle may have a tire speed rating above the maximum speed permitted by the elec- tronic speed limiter. Make sure your tires have the required tire speed rating as specified for your vehicle in the “Technical data” section (컄 page 481), for example when purchasing new tires. For information on how to identify the tire speed rating on a tire’s sidewall, see “Tire size designation, load and speed rating” (컄 page 350).

315

Operation Driving instructions

If you are uncertain about the correct read- ing of the information given on a tire’s side- wall, any authorized Mercedes-Benz Center will be glad to assist you.

i For information on speed ratings for winter tires, see “Winter driving” (컄 page 364). For additional general information on tire speed markings on tire sidewall, see “Tire speed rating” (컄 page 352).

316

Winter driving instructions

The most important rule for slippery or icy roads is to drive sensibly and to avoid abrupt acceleration, braking and steering maneuvers. Do not use the cruise control system under such conditions. When the vehicle is in danger of skidding, move gear selector lever to position N. Try to keep the vehicle under control by cor- rective steering action.

i For more information on driving with snow chains, see “Snow chains” (컄 page 365).

Road salts and chemicals can adversely af- fect braking efficiency. Increased pedal force may become necessary to produce the normal braking effect. Depressing the brake pedal periodically when traveling at length on salt-strewn roads can bring road-salt-impaired braking efficiency back to normal. If the vehicle is parked after being driven on salt-treated roads, the braking efficien- cy should be tested as soon as possible af- ter driving is resumed.

Warning!

Warning!

On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehi- cle control. Your vehicle’s ABS will not pre- vent this type of control loss.

Make sure not to endanger any other road users when carrying out these braking ma- neuvers.

Operation Driving instructions

Warning!

Standing water

Passenger compartment

! Do not drive through flooded areas or water of unknown depth. Before driving through water, determine its depth. Never accelerate before driving into water. The bow wave could force wa- ter into the engine and auxiliary equipment, thus damaging them. If you must drive through standing water, drive slowly to prevent water from entering the pas- senger compartment or the engine compart- ment. Water in these areas could cause damage to electrical components or wiring of the engine or transmission, or could result in water being in- gested by the engine through the air intake caus- ing severe internal engine damage. Any such damage is not covered by the Mercedes-Benz Limited Warranty.

If the vehicle becomes stuck in snow, make sure that snow is kept clear of the exhaust pipe and from around the vehicle with the engine running. Otherwise, deadly carbon monoxide (CO) gases may enter vehicle in- terior resulting in unconsciousness and death.

To assure sufficient fresh air ventilation, open a window slightly on the side of the ve- hicle not facing the wind.

Warning!

The outside temperature indicator is not de- signed to serve as an ice-warning device and is therefore unsuitable for that purpose. In- dicated temperatures just above the freez- ing point do not guarantee that the road surface is free of ice.

For more information, see “Winter driving” (컄 page 364).

Warning!

Always fasten items being carried as secure- ly as possible.

In an accident, during hard braking or sud- den maneuvers, loose items will be thrown around inside the vehicle, and cause injury to vehicle occupants unless the items are securely fastened in the vehicle.

The trunk is the preferred place to carry ob- jects.

Driving abroad

Abroad, there is an extensive Mercedes-Benz service network at your disposal. If you plan to drive into areas which are not listed in the index of your Mercedes-Benz Center directory, you should request pertinent information from your authorized Mercedes-Benz Center.

317

Operation Driving instructions

Control and operation of radio trans- mitter

COMAND, radio and telephone*

Warning!

Please do not forget that your primary re- sponsibility is to drive the vehicle safely. Only operate the COMAND (Cockpit Man- agement and Data System), radio or tele- phone1 if road, weather and traffic conditions permit.

Bear in mind that at a speed of just 30 mph (approximately 50 km/h), your vehicle is covering a distance of 44 feet (approximate- ly 14 m) every second.

1 Observe all legal requirements.

318

Telephones and two-way radios

Catalytic converter (gasoline engine)

Warning!

Never operate radio transmitters equipped with a built-in or attached antenna (i.e. with- out being connected to an external antenna) from inside the vehicle while the engine is running. Doing so could lead to a malfunc- tion of the vehicle’s electronic system, pos- sibly resulting in an accident and/or serious personal injury.

Radio transmitters, such as a portable tele- phone or a citizens band unit should only be used inside the vehicle if they are con- nected to an antenna that is installed on the outside of the vehicle. Refer to the radio transmitter operation in- structions regarding use of an external an- tenna.

Your vehicle is equipped with monolithic-type catalytic converters, an important element in conjunction with the oxygen sensors to achieve substantial con- trol of the pollutants in the exhaust emis- sions. Keep your vehicle in proper operating condition by following our rec- ommended maintenance instructions as outlined in your Maintenance Booklet.

! To prevent damage to the catalytic convert- ers, only use premium unleaded gasoline in this vehicle. Any noticeable irregularities in engine operation should be repaired promptly. Otherwise, exces- sive unburned fuel may reach the catalytic con- verter, causing it to overheat, which could potentially start a fire.

Warning!

As with any vehicle, do not idle, park or op- erate this vehicle in areas where combusti- ble materials such as grass, hay or leaves can come into contact with the hot exhaust system, as these materials could be ignited and cause a vehicle fire.

Operation Driving instructions

Oxidation catalyst (diesel engine)

Emission control

Your vehicle is equipped with an oxidation catalyst, an important element in conjunc- tion with the oxygen sensors to achieve substantial control of the pollutants in the exhaust emissions. Keep your vehicle in proper operating condition by following our recommended maintenance instruc- tions as outlined in your Maintenance Booklet.

Warning!

As with any vehicle, do not idle, park or op- erate this vehicle in areas where combusti- ble materials such as grass, hay or leaves can come into contact with the hot exhaust system, as these materials could be ignited and cause a vehicle fire.

Certain parts of the engine and the emission control system serve to keep the toxic components of the exhaust gases of the engine within permissible limits re- quired by law. These systems will function properly only when maintained strictly according to factory specifications. Any adjustments on the engine should, therefore, be carried out only by qualified Mercedes-Benz Center authorized technicians. Engine adjustments should not be altered in any way. Moreover, the specified service procedures must be carried out regularly according to Mercedes-Benz servicing requirements. For details refer to the Maintenance Booklet.

319

Operation Driving instructions

Warning!

Coolant temperature

Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide (CO), and inhaling it can cause un- consciousness and lead to death.

Do not run the engine in confined areas (such as a garage) which are not properly ventilated. If you think that exhaust gas fumes are entering the vehicle while driving, have the cause determined and corrected immediately. If you must drive under these conditions, drive only with at least one win- dow fully open at all times.

During severe operating conditions and stop-and-go city traffic, the coolant tem- perature may rise close to approximately 248°F (120°C). The engine should not be operated with the coolant temperature over 248°F (120°C). Doing so may cause serious en- gine damage which is not covered by the Mercedes-Benz Limited Warranty.

Warning!

앫 Driving when your engine is overheated can cause some fluids, which may have leaked into the engine compartment, to catch fire. You could be seriously burned.

앫 Steam from an overheated engine can cause serious burns which can occur just by opening the engine hood. Stay away from the engine if you see or hear steam coming from it.

Turn off the engine, get out of the vehicle and do not stand near the vehicle until the engine has cooled down.

320

왔 At the gas station Refueling

Warning!

Gasoline and diesel fuels are highly flammable and poisonous. They burn violently and can cause serious injury.

Never allow sparks, flame or smoking materials near gasoline or diesel fuel!

Turn off the engine before refueling.

Whenever you are around gasoline or diesel fuel, avoid inhaling fumes and skin or clothing contact, extinguish all smoking materials.

Direct skin contact with gasoline or diesel fuels and the inhalation of gasoline or diesel fuel vapors can damage your health.

Warning!

Do not fill diesel tanks with gasoline. Do not mix diesel fuel with gasoline. Otherwise the fuel system and engine could be damaged. In addition, the vehicle could catch fire.

If you have accidentally filled the tank with incorrect or non-approved fuel, do not start the engine. The fuel system must be drained completely.

! Damage resulting from the use of non ap- proved fuels or fuel additives or resulting from mixing gasoline with diesel fuel is not covered by the Mercedes-Benz Limited Warranty.

The fuel filler flap is located on the right-hand side of the vehicle towards the rear. Locking/unlocking the vehicle with the SmartKey or the SmartKey with KEYLESS-GO* automatically locks/un- locks the fuel filler flap.

Operation At the gas station

! Diesel engine: When filling the diesel fuel tank using fuel con- tainers, place a filling filter, a suede cloth or a clean flannel cloth as a filter. Otherwise, parti- cles from the fuel container could clog the fuel lines and/or the diesel injection system.

i In case that the central locking system does not release the fuel filler flap, or the opening mechanism is clamping, notify Roadside Assis- tance or an authorized Mercedes-Benz Center.

왘 Turn the engine off

앫 by turning the SmartKey to

position 0.

컄컄

321

Operation At the gas station

컄컄

앫 by pressing the KEYLESS-GO*

start/stop button. Open the driv- er’s door (with the driver’s door open, starter switch is now in position 0, same as SmartKey re- moved from starter switch).

왘 Remove the SmartKey from the starter

switch.

왘 Open the fuel filler flap by pushing at

the point indicated by the arrow. The fuel filler flap springs open.

왘 Turn the fuel cap to the left and hold on to it until possible pressure is released. 왘 Take off the cap and set it in the recess

on the fuel filler flap. To prevent fuel vapors from escaping into open air, fully insert filler nozzle unit.

왘 Only fill your tank until the filler nozzle unit cuts out – do not top off or over- fill.

322

Warning!

Overfilling of the fuel tank may create pressure in the system which could cause a gas discharge. This could cause the gas to spray back out when removing the fuel pump nozzle, which could cause personal injury.

왘 Replace fuel cap by turning it clockwise

until it audibly engages. 왘 Close the fuel filler flap.

i Leaving the engine running and the fuel cap open can cause the yellow fuel tank reserve warning lamp to flash and the malfunction indi- cator lamp ú (USA only) or the malfunction indicator lamp ± (Canada only) to illuminate. For more information, see also “Practical hints” (컄 page 384).

i Gasoline engine: Only use premium unleaded gasoline with a min- imum Posted Octane Rating of 91 (average of 96 RON/86 MON). Information on gasoline quality can normally be found on the fuel pump. For more information on gasoline, see “Premium unleaded gasoline (gasoline engine)” (컄 page 496), see “Fuel requirements” (컄 page 496) and the Factory Approved Service Products pamphlet (USA only) or contact an authorized Mercedes-Benz Center.

i Diesel engine: Only use commercially available vehicular ULTRA-LOW SULFUR DIESEL FUEL (15 ppm SULFUR MAXIMUM). Information on diesel quality can normally be found on the fuel pump. For more information on diesel fuels, refer to the Factory Approved Service Products pamphlet (USA only) or contact an authorized Mercedes-Benz Center.

i Diesel engine: If you have driven the vehicle until the tank is empty, the fuel system needs to be bled (컄 page 459).

! Diesel engine: The engine is more susceptible to wear and damage if you use 앫 marine diesel fuel 앫 heating oil 앫 additives The exhaust aftertreatment device will be seriously damaged if you use 앫 LOW SULFUR DIESEL FUEL

(500 ppm SULFUR MAXIMUM)

앫 any other diesel fuel with a sulfur content of

above 15 ppm

The use of such non-approved fuels and/or special additives is not covered by the Mercedes-Benz Limited Warranty.

Low outside temperatures (diesel engine) To prevent malfunctions, diesel fuel with improved cold flow characteristics is of- fered in the winter months. Check with your fuel retailer.

! Do not fill the tank with gasoline. Do not blend diesel fuel with gasoline or kerosine. The fuel system and engine will otherwise be dam- aged, which is not covered by the Mercedes-Benz Limited Warranty.

Operation At the gas station

Check regularly and before a long trip

1 Windshield washer system and head-

lamp cleaning system*

2 Brake fluid 3 Coolant level

323

Operation At the gas station

Windshield washer system and headlamp cleaning system* For information on refilling the reservoir, see “Windshield washer system and headlamp cleaning system*” (컄 page 332).

Coolant For normal replenishing, use water (pota- ble water quality). For more information on coolant, see “Coolant level” (컄 page 330) and see “Fuels, coolants, lubricants etc.” (컄 page 491).

Engine oil level For more information on engine oil level, see “Engine oil” (컄 page 327).

Brake fluid

! If you find that the brake fluid in the brake fluid reservoir has fallen to the minimum mark or below, have the brake system checked for brake pad thickness and leaks immediately. Notify an authorized Mercedes-Benz Center immediately. Do not add brake fluid as this will not solve the problem. For more information, see “Practical hints” (컄 page 383). For information on brake fluid, see “Fuels, coolants, lubricants etc.” (컄 page 491).

Vehicle lighting Check function and cleanliness. For more information on replacing light bulbs, see “Replacing bulbs” (컄 page 443). For more information, see “Exterior lamp switch” (컄 page 137).

Tire inflation pressure For more information, see “Checking tire inflation pressure” (컄 page 342).

324

왔 Engine compartment Hood

Warning!

Warning!

Operation Engine compartment

Warning!

Do not pull the release lever while the vehi- cle is in motion. Otherwise the hood could be forced open by passing air flow.

This could cause the hood to come loose and injure you and/or others.

You could be injured when the hood is open – even when the engine is turned off.

Parts of the engine can become very hot. To prevent burns, let the engine cool off com- pletely before touching any components on the vehicle. Comply with all relevant safety precautions.

Opening

Warning!

If you see flames or smoke coming from the engine compartment, or if the coolant tem- perature indicator indicates that the engine is overheated, do not open the hood. Move away from vehicle and do not open the hood until the engine has cooled. If necessary, call the fire department.

Warning!

To help prevent personal injury, stay clear of moving parts when the hood is open and the engine is running.

The radiator fan may continue to run for ap- proximately 30 seconds or may even restart after the engine has been turned off. Stay clear of fan blades.

Vehicles with gasoline engine: The engine is equipped with a transistorized ignition system. Because of the high voltage it is dangerous to touch any components (ig- nition coils, spark plug sockets, diagnostic socket) of the ignition system 앫 with the engine running 앫 while starting the engine 앫 if ignition is “on” and the engine is

turned manually

325

Operation Engine compartment

Warning!

Vehicles with diesel engine: The engine is equipped with a high-voltage electronic control unit for the injection system. Because of the high voltage it is dangerous to touch any components of the injection system (injectors, electrical wires) 앫 with the engine running 앫 while starting the engine 앫 when the ignition is switched on

326

1 Release lever 왘 Pull release lever 1. The hood is unlocked.

2 Handle for opening the hood 왘 Lift the hood slightly.

Handle 2 will extend out of the radia- tor grille.

! To avoid damage to the windshield wipers or hood, never open the hood if the wiper arms are folded forward away from the windshield.

! To avoid damage to handle 2 never pull up the hood on handle 2.

왘 Pull handle 2 to its stop out of radia-

Closing

Engine oil

Operation Engine compartment

tor grille.

왘 Lift bottom of hood at edge of radiator

grille. The hood will be automatically held open at shoulder height by gas-filled struts.

The amount of oil your engine needs will depend on a number of factors, including driving style. Higher oil consumption can occur when 앫 the vehicle is new 앫 the vehicle is driven frequently at

higher engine speeds

Engine oil consumption checks should only be made after the vehicle break-in period.

i Do not use any special lubricant additives, as these may damage the drive assemblies. Us- ing special additives not approved by Mercedes-Benz may cause damage not covered by the Mercedes-Benz Limited Warranty. More information on this subject is available at any Mercedes-Benz Center.

Warning!

When closing the hood, use extreme caution not to catch hands or fingers. Be careful that you do not close the hood on anyone.

Make sure that the hood is securely en- gaged before driving off. Do not continue driving if the hood can no longer engage af- ter an accident, for example. The hood could otherwise come loose while the vehicle is in motion and endanger you and others.

왘 Let the hood drop from a height of ap-

proximately 1 ft (30 cm). The hood will lock audibly.

왘 Check to make sure the hood is fully

closed. If you can raise the hood at a point above the headlamps, then it is not properly closed. Open it again and let it drop with somewhat greater force.

327

Operation Engine compartment

Checking engine oil level When checking the oil level 앫 the vehicle must be parked on level

ground

앫 with the engine at operating tempera- ture, the vehicle must have been sta- tionary for at least 5 minutes with the engine turned off

앫 with the engine not at operating tem- perature yet, the vehicle must have been stationary for at least 5 minutes with the engine turned off

328

왘 Pull out oil dipstick 1 again after

approximately 3 seconds to obtain ac- curate reading. The oil level is correct when it is be- tween the lower (min) mark 3 and upper (max) mark 2 of oil dipstick 1.

i All models (except E 63 AMG): The filling quantity between the upper and lower marks on the oil dipstick is approximately 2.1 US qt. (2.0 l). E 63 AMG: The filling quantity between the upper and lower marks on the oil dipstick is approximately 1.6 US qt. (1.5 l). 왘 If necessary, add engine oil. For adding engine oil, see “Adding engine oil”. For more information on engine oil, see “Fuels, coolants, lubricants etc.” (컄 page 491). For more information on messages in the multifunction display concerning engine oil, see the “Practical hints” section (컄 page 418).

1 Oil dipstick 2 Upper (max) mark 3 Lower (min) mark To check the engine oil level with the oil dipstick, do the following: 왘 Open the hood (컄 page 325). 왘 Pull out oil dipstick 1. 왘 Wipe oil dipstick 1 clean. 왘 Fully insert oil dipstick 1 into the

dipstick guide tube.

Adding engine oil

! Only use approved engine oils and oil filters required for vehicles with Maintenance System (U.S. vehicles) or FSS PLUS (Canada vehicles). For a listing of approved engine oils and oil fil- ters, refer to the Factory Approved Service Products pamphlet (USA only) in your vehicle literature portfolio, or contact an authorized Mercedes-Benz Center. Using engine oils and oil filters of specification other than those expressly required for the Main- tenance System (U.S. vehicles) or FSS PLUS (Canada vehicles), or changing of oil and oil filter at change intervals longer than those called for by the Maintenance System (U.S. vehicles) or FSS PLUS (Canada vehicles) will result in engine or emission control system damage not covered by the Mercedes-Benz Limited Warranty.

Operation Engine compartment

Be careful not to spill any oil when adding. Avoid environmental damage caused by oil entering the ground or water.

! Excess oil must be siphoned or drained off. It could cause damage to the engine and emis- sion control system not covered by the Mercedes-Benz Limited Warranty. 왘 Screw filler cap 1 back on filler neck. For more information on engine oil, see the “Technical data” section (컄 page 491) and (컄 page 495).

Transmission fluid level

The transmission fluid level does not need to be checked. If you notice transmission fluid loss or gear shifting malfunctions, have an authorized Mercedes-Benz Center check the transmission.

329

E 350/E 550 (E 320 BLUETEC similar)

E 63 AMG 왘 Unscrew filler cap 1 from filler neck. 왘 Add engine oil as required. Be careful

not to overfill with oil.

Operation Engine compartment

Coolant level

The engine coolant is a mixture of water and anticorrosion/antifreeze. To check the coolant level, the vehicle must be parked on level ground and the engine must be cool. The coolant expansion tank is located on the driver’s side of the engine compart- ment.

Warning!

In order to avoid any potentially serious burns: 앫 Use extreme caution when opening the hood if there are any signs of steam or coolant leaking from the cooling system, or if the coolant temperature gauge indi- cates that the coolant is overheated.

앫 Do not remove pressure cap on coolant

reservoir if coolant temperature is above 158°F (70°C). Allow engine to cool down before removing cap. The coolant reservoir contains hot fluid and is under pressure.

330

앫 Do not spill antifreeze on hot engine

parts. Antifreeze contains ethylene gly- col which may burn if it comes into con- tact with hot engine parts.

앫 Using a rag, slowly open the cap approx- imately 1/2 turn to relieve excess pres- sure. If opened immediately, scalding hot fluid and steam will be blown out un- der pressure.

왘 Using a rag, turn cap 2 slowly approx- imately one half turn counterclockwise to release any excess pressure.

왘 Continue turning the cap 2 counter-

clockwise and remove it. The coolant level is correct if the level: 앫 for cold coolant: reaches marking

bar 1 in the expansion tank 3

앫 for warm coolant: is approximately

0.6 in (1.5 cm) higher 왘 Add coolant as required. 왘 Replace and tighten cap 2. For more information on coolant, see the “Technical data” section (컄 page 498).

1 Marking bar in the expansion tank 2 Cap 3 Coolant expansion tank

Battery

Your vehicle’s battery is located on the right hand side of the trunk (컄 page 460). The battery should always be sufficiently charged in order to achieve its rated ser- vice life. Refer to Maintenance Booklet for battery maintenance intervals. If you use your vehicle mostly for short-dis- tance trips, you will need to have the bat- tery charge checked more frequently. When replacing the battery, always use batteries approved by Mercedes-Benz. If you do not intend to operate your vehicle for an extended period of time, consult an authorized Mercedes-Benz Center about steps you need to observe.

Warning!

Observe all safety instructions and precau- tions when handling automotive batteries.

Risk of explosion.

Fire, open flames and smoking are prohibited when handling batteries. Avoid creating sparks.

Battery acid is caustic. Do not allow it to come into contact with skin, eyes or clothing.

Wear suitable protective cloth- ing, especially gloves, apron and faceguard.

Operation Engine compartment

Wear eye protection.

Rinse any acid spills immediate- ly with clear water. Contact a physician if necessary.

Keep children away.

Follow the instructions in this Operator’s Manual.

Batteries contain materials that can harm the environment if disposed of improperly. Recycling of batteries is the preferred method of disposal. Many states require sellers of batteries to accept old batteries for recycling.

331

Operation Engine compartment

Windshield washer system and headlamp cleaning system*

The windshield washer reservoir is located in the engine compartment.

1 Cap for windshield washer reservoir Fluid for the windshield washer system and the headlamp cleaning system is supplied from the windshield washer reservoir. It has a capacity of: 앫 4.8 US qt (4.5 l) in vehicles without