Download PDF Manual

5 Air distribution


6 Rear window defroster 7 Temperature control, passenger side 8 MAX COOL on/off 9 AC cooling on/off a Climate control on/off


b Decreasing air volume c Air recirculation d Air distribution and air volume


(automatic, manual)


206


Controls in detail Dual-zone automatic climate control


Canada only


1 Temperature control, driver’s side 2 Front defroster 3 Increasing air volume 4 Display 5 Air distribution


6 Rear window defroster 7 Temperature control, passenger side 8 Residual heat/ventilation 9 AC cooling on/off a Climate control on/off


b Decreasing air volume c Air recirculation d Air distribution and air volume


(automatic, manual)


207


i Severe conditions (e.g. strong air pollution) may require replacement of the filter before its scheduled interval. A clogged filter will reduce the air volume to the interior. If the vehicle interior is hot, ventilate the interior before driving off, see “Summer opening fea- ture” (컄 page 239). The climate control will then adjust the interior temperature to the set value much faster. Keep the air intake grille in front of the wind- shield free of snow and debris. Do not obstruct air flow by placing objects on the air flow-through exhaust slots below the rear window.


Controls in detail Dual-zone automatic climate control


The climate control is operational whenev- er the engine is running. You can operate the climate control system in either the au- tomatic or manual mode. The system cools or heats the interior depending on the se- lected interior temperature and the cur- rent outside temperature.


Nearly all dust particles, pollutants and odors are filtered out before outside air en- ters the passenger compartment through the air distribution system. The air conditioning will not engage (no cooling) if the A/C mode is deactivated (컄 page 217).


Warning!


Warning!


Follow the recommended settings for heat- ing and cooling given on the following pag- es. Otherwise the windows could fog up, impairing visibility and endangering you and others.


When operating the climate control, the air that enters the passenger compartment through the air vents can be very hot or very cold (depending on the set temperature). This may cause burns or frostbite to unpro- tected skin in the immediate area of the air vents. Always keep sufficient distance be- tween unprotected parts of the body and the air vents. If necessary, use the air distribu- tion control (컄 page 206) to direct the air to air vents in the vehicle interior that are not in the immediate area of unprotected skin.


208


Controls in detail Dual-zone automatic climate control


Deactivating the climate control system


Warning!


i To switch the system on, you can also press another button, with the exception of 1 or F.


Operating the climate control system in automatic mode


When the climate control is switched off, the outside air supply and circulation are also switched off. Only choose this setting for a short time. Otherwise the windows could fog up, impairing visibility and endangering you and others.


Deactivating 왘 Press button ´ (컄 page 206) or


(컄 page 207).


Reactivating 왘 Make sure the ignition is switched on. 왘 Press button ´ (컄 page 206) or


(컄 page 207) again. The previous settings are once again in effect.


i When operating the climate control system in automatic mode, you will only rarely need to adjust the temperature, air volume and air distri- bution. In automatic mode, cooling with dehumidify is switched on. This function can be switched off.


Warning!


If you switch off the cooling function the windows can fog up more quickly. Window fogging may impair visibility and endanger you and others.


Activating 왘 Press button U (컄 page 206) or (컄 page 207) while the engine is run- ning. The indicators for automatic air volume and air distribution in display 4 (컄 page 206) or (컄 page 207) come on. Air volume and air distribution are automatically controlled.


왘 Use temperature controls 1 and 7 (컄 page 206) or (컄 page 207) to sepa- rately adjust the air temperature on each side of the passenger compart- ment. The temperature of the vehicle interior is adjusted automatically.


209


Decreasing 왘 Turn temperature control 1 and/or


7 (컄 page 206) or (컄 page 207) slightly counterclockwise. The climate control system will corre- spondingly adjust the interior air tem- perature.


Controls in detail Dual-zone automatic climate control


Deactivating 왘 Press button ˜ or Q


(컄 page 206) or (컄 page 207). The AUTO indicator for air volume in the display 4 (컄 page 206) or (컄 page 207) goes out. The automatic function for air volume is switched off, and air volume is controlled according to the desired setting. Automatic air distribution remains switched on.


or 왘 Press air distribution button 5


(컄 page 206) or (컄 page 207). The AUTO indicator for air distribution in the display 4 (컄 page 206) or (컄 page 207) goes out. The automatic function for air distribution is switched off, and air distribution is controlled ac- cording to the desired position. Auto- matic air volume remains switched on.


Setting the temperature


Use temperature controls 1 and 7 (컄 page 206) or (컄 page 207) to separate- ly adjust the air temperature on each side of the passenger compartment. You should raise or lower the temperature set- ting in small increments, preferably start- ing at 72°F (22°C). The climate control will adjust to the set temperature as fast as possible.


Increasing 왘 Turn temperature control 1 and/or


7 (컄 page 206) or (컄 page 207) slightly clockwise. The climate control system will corre- spondingly adjust the interior air tem- perature.


210


Adjusting air distribution


Use air distribution control rocker switch 5 (컄 page 206) or (컄 page 207) to adjust the air distribution.


Controls in detail Dual-zone automatic climate control


The following symbols are located in the display 4 (컄 page 206) or (컄 page 207):


Symbol Function b Directs air into the entire


vehicle interior


c Directs air to the windshield, through the side air vents and cockpit air vent (Canada only) Z Directs air to the windshield and through the side air vents X Directs air to the windshield, through the side air vents and to the footwells


a Directs air through the cockpit (Canada only), center, side and rear passenger compartment air vents


Y Directs air to the footwells d Directs air to the footwells and


through the side air vents


왘 Use air distribution control rocker


switch 5 (컄 page 206) or (컄 page 207) until the desired symbol appears in the display 4 (컄 page 206) or (컄 page 207). The AUTO indicator for automatic air dis- tribution in the display 4 goes out. The automatic function for air distribu- tion is switched off, and air distribution is controlled according to the desired setting.


i The air volume continues to be controlled according to the indicator in the display 4.


Opening the cockpit air vent (Canada only) and center air vents 왘 Turn thumbwheels 1 and 5


(컄 page 204) upward. The cockpit air vent 3 and the center air vents 2 and 4 are open.


211


Controls in detail Dual-zone automatic climate control


Adjusting air volume


Front defroster


You can use this setting to defrost the windshield, for example if it is iced up. You can also defog the windshield and the windows.


i Keep this setting selected only until the windshield or the windows are clear again.


Nine blower speeds are available. 왘 Press button ˜ to decrease or Q to increase air volume (컄 page 206) or (컄 page 207) to the desired level. The AUTO indicator for air volume in the display 4 (컄 page 206) or (컄 page 207) goes out. The automatic function for air volume is switched off, and air volume is controlled according to the desired setting.


i The air distribution continues to be con- trolled according to the indicator in the display 4.


Closing the cockpit air vent (Canada only) and the center air vents 왘 Turn thumbwheels 1 and 5


(컄 page 204) downward. The cockpit air vent 3 and the center air vents 2 and 4 are closed.


Opening the side air vents 왘 Turn thumbwheels 8 and a


(컄 page 204) upward. The side air vents 7 and b are open.


Closing the side air vents 왘 Turn thumbwheels 8 and a


(컄 page 204) downward. The side air vents 7 and b are closed.


212


Controls in detail Dual-zone automatic climate control


Deactivating 왘 Press button 0 or


P (컄 page 206) or (컄 page 207) again. The indicator lamp on the button goes out. Defrosting is turned off. The previous settings are once again in effect.


i The cooling remains switched on.


Windshield fogged on the outside


i Keep this setting selected only until the windshield is clear again. 왘 Switch the windshield wipers on


(컄 page 58).


If the automatic air distribution is switched off: 왘 Turn air distribution control 5 to a or Y (컄 page 206) or (컄 page 207).


Activating 왘 Press button 0 or


P (컄 page 206) or (컄 page 207). The indicator lamp on the button comes on. The air conditioning switches automatically to the following func- tions: 앫 cooling on to dehumidify 앫 maximum blowing and heating


power (depends on cooling temperature)


앫 air flows onto the windshield and


the front side windows


앫 the air recirculation mode is


switched off


i If you have switched on the defrost function using the 0 or P button, you cannot make any other settings.


213


Controls in detail Dual-zone automatic climate control


Deactivating 왘 Press button 8 (컄 page 206) again. MAX COOL disappears in the display 4 (컄 page 206). The previous settings are once again in effect.


i To switch the maximum cooling function off, you can also press button ´, U, 0 or 1 (컄 page 206).


Air recirculation mode


Switch to air recirculation mode to prevent unpleasant odors from entering the vehicle from the outside (e.g. before a driving through a tunnel). This setting cuts off the intake of outside air and recirculates the air in the passenger compartment.


Warning!


Fogged windows impair visibility, endanger- ing you and others. If the windows begin to fog on the inside, switching off the air recirculation mode immediately should clear interior window fogging. If interior window fogging persists, make sure the air conditioning (컄 page 217) is activated, or press button 0 or P.


Maximum cooling MAX COOL (USA only)


You can use this setting to provide the fast- est possible cooling of the vehicle interior (when windows and tilt/sliding sunroof or tilt/sliding panel* are closed).


Activating 왘 Press button 8 (컄 page 206).


MAX COOL appears in the display 4 (컄 page 206).


The air conditioning switches automatically to the following functions: 앫 maximum cooling 앫 maximum blowing power 앫 the air recirculation mode is switched


on


214


Controls in detail Dual-zone automatic climate control


Activating 왘 Briefly press button , (컄 page 206)


or (컄 page 207). The indicator lamp on the button comes on.


i The air recirculation mode is activated auto- matically at high outside temperatures. The indicator lamp on button , is not lit when the air recirculation mode is automatically switched on. A quantity of outside air is added after approxi- mately 30 minutes. If you have turned off the air conditioning (컄 page 217) or the outside temperature is be- low 41°F (5°C), the air recirculation mode will not switch on automatically.


Deactivating 왘 Press button , (컄 page 206) or


(컄 page 207). The indicator lamp on the button goes out.


i The air recirculation mode is deactivated au- tomatically: 앫 after 5 minutes if the outside temperature is


below approximately 41°F (5°C)


앫 after 5 minutes if the air conditioning is


turned off


앫 after 30 minutes if the outside temperature


is above approximately 41°F (5°C)


Air recirculation mode with conve- nience closing or opening feature


Warning!


Never operate the windows and tilt/sliding sunroof or tilt/sliding panel* if there is the possibility of anyone being harmed by the opening or closing procedure.


In the event that the procedure causes po- tential danger, the closing of the windows can be immediately halted by pressing or pulling the respective window switch. The closing of the tilt/sliding sunroof can be im- mediately halted by moving the switch for the tilt/sliding sunroof in any direction.


컄컄


215


Controls in detail Dual-zone automatic climate control


컄컄


Vehicles with panorama roof*: When using the air recirculation mode with convenience closing feature, should the up- ward movement of a window be blocked by some obstruction including but not limited to arms, hands, fingers, etc., the automatic reversal feature will not operate. In the event that the procedure causes po- tential danger, the closing of the windows and tilt/sliding panel can be immediately halted by releasing the , button. The closing of the windows and the tilt/slid- ing sunroof can be reversed by again press- ing and holding the , button.


Convenience closing 왘 Press button , (컄 page 206) or


(컄 page 207) for approximately 2 seconds. The windows and tilt/sliding sunroof will close. You can release button , once the closing procedure has begun. The windows and tilt/sliding sunroof continue closing until they are fully closed. The indicator lamp on the but- ton comes on. The air recirculation mode is activated.


Convenience opening 왘 Press button , for approximately


2 seconds. The windows and tilt/sliding sunroof will return to their previous position. You can release button , once the opening procedure has begun. The win- dows and tilt/sliding sunroof continue opening until they have reached their previous position. The indicator lamp on the button goes out. The air recircu- lation mode is deactivated.


i A window or tilt/sliding sunroof will only re- turn to its previous position if it has not been moved to another position using the respective window switch or tilt/sliding sunroof switch af- ter it was closed with button ,. A window or tilt/sliding sunroof that has been moved will remain in its current position if button , is used to reopen the remaining windows or tilt/sliding sunroof.


216


Controls in detail Dual-zone automatic climate control


Deactivating It is possible to deactivate the air condi- tioning (cooling) function of the climate control system. The air in the vehicle will then no longer be cooled or dehumidified. 왘 Press button 2 (컄 page 206) or


(컄 page 207). The indicator lamp on the button goes out.


Vehicles with panorama roof* Convenience closing: 왘 Press and hold button ,


(컄 page 206) or (컄 page 207) until the windows and the tilt/sliding panel are closed or have reached the desired po- sition. The indicator lamp on the button comes on. The air recirculation mode is activated.


Convenience opening: 왘 Press and hold button , until the windows and the tilt/sliding panel are opened or have reached the desired position. The indicator lamp on the but- ton goes out. The air recirculation mode is deactivated.


Air conditioning


The cooling function, only operational when the engine is running, cools the vehi- cle interior down to the selected tempera- ture. The cooling function also dehumidifies the air in the vehicle interior, thus preventing the windows from fogging up.


i Condensation may drip out from underneath the vehicle. This is normal and not an indication of a malfunction.


Warning!


If you turn off the cooling function, the vehicle will not be cooled when weather conditions are warm. The windows can fog up more quickly. Window fogging may impair visibility and endanger you and others.


217


Controls in detail Dual-zone automatic climate control


Activating Moist air can fog up the windows. You can dehumidify the air with the air condition- ing. 왘 Press button 2 (컄 page 206) or


(컄 page 207) again. The indicator lamp on the button comes on.


The air conditioning uses the refrigerant R134a. This refrigerant is free of CFCs which are harmful to the ozone layer.


! If the air conditioning cannot be turned on again, this indicates that the air conditioning is losing refrigerant. The compressor has turned it- self off. Have the air conditioning checked at the nearest authorized Mercedes-Benz Center.


Residual heat and ventilation (Canada only)


With the engine switched off, it is possible to continue to heat or ventilate the interior for up to 30 minutes. This feature makes use of the residual heat produced by the engine.


i If you switch on the residual heat function when temperatures are high, only the ventilation will be switched on.


i Regardless of the selected air volume, the blower operates at low speed.


i How long the system will provide heating de- pends on 앫 the coolant temperature 앫 the temperature set by the operator The blower will run at speed setting 1 regardless of the air distribution control setting.


Activating 왘 Switch off the ignition. 왘 Press button T (컄 page 207).


REST in the display 4 (컄 page 207) comes on.


Deactivating 왘 Press button T (컄 page 207) again.


REST in the display 4 (컄 page 207) goes out.


i The residual heat is automatically turned off: 앫 when the ignition is switched on 앫 after about 30 minutes 앫 if the battery voltage drops 앫 if the coolant temperature is too low


218


Controls in detail Dual-zone automatic climate control


The air vents for the rear passenger compartment are located in the rear center console.


Rear passenger compartment adjustable air vents


The air conditioning for the rear passenger compartment is controlled via the climate control panel (컄 page 206) or (컄 page 207).


i The temperature at the center air vents 1 and 2 for the rear passenger compartment is nearly the same as at the dashboard center air vents.


1 Left center air vent, adjustable 2 Right center air vent, adjustable 3 Thumbwheel for air volume control for


right rear center air vent


4 Thumbwheel for air volume control for


left rear center air vent


Adjusting air distribution 왘 Move the slider for the left center air vent 1 or right center air vent 2 to the left, right, up or down. The air flow is directed in the corre- sponding direction.


i For draft-free ventilation, move the sliders for the center air vents 1 and 2 upward.


Adjusting air volume 왘 Turn thumbwheel 3 or 4 up or down.


The air volume is increased or decreased.


219


Controls in detail 4-zone automatic climate control


(only available on E 550, E 550 4MATIC, E 63 AMG)


220


1 Thumbwheel for air volume control


for left center air vent


2 Left center air vent, adjustable 3 Cockpit air vent, fixed (Canada only) 4 Right center air vent, adjustable 5 Thumbwheel for air volume control


for right center air vent


6 Right side defroster air vent, fixed 7 Right side air vent, adjustable 8 Thumbwheel for air volume control


for right side air vent 9 Climate control panel a Thumbwheel for air volume control


for left side air vent


b Left side air vent, adjustable c Left side defroster air vent, fixed


Controls in detail 4-zone automatic climate control


i For draft-free ventilation, move the sliders for the center air vents and side air vents to the middle position.


1 Thumbwheel for air volume control


for side air vent


2 Side air vent, adjustable


221


Controls in detail 4-zone automatic climate control


USA only


1 Air distribution, driver’s side 2 Front defroster 3 Temperature rocker switch, driver’s


side


4 Display 5 Temperature rocker switch,


passenger side


6 Rear window defroster


222


7 Air distribution, passenger side 8 Air distribution and air volume,


passenger side (automatic, manual)


9 AC cooling on/off a Rear air-conditioning remote control b Increasing air volume


c Climate control on/off d Decreasing air volume e MAX COOL on/off f Air recirculation g Air distribution and air volume, driver’s side (automatic, manual)


Controls in detail 4-zone automatic climate control


Canada only


1 Air distribution, driver’s side 2 Front defroster 3 Temperature rocker switch, driver’s


side


4 Display 5 Temperature rocker switch,


passenger side


6 Rear window defroster


7 Air distribution, passenger side 8 Air distribution and air volume,


passenger side (automatic, manual)


9 AC cooling on/off a Rear air-conditioning remote control b Increasing air volume


c Climate control on/off d Decreasing air volume e Residual heat/ventilation f Air recirculation g Air distribution and air volume, driver’s side (automatic, manual)


223


The climate control is a 4-zone intelligent climate control system. Your vehicle interi- or is divided into 4 zones.


With the help of a sun sensor, the climate control determines the relation of the sun to the vehicle and automatically adjusts the inside temperature for every individual zone. You can set the temperature for each of the 4 zones separately. The climate control is operational whenev- er the engine is running. It cools the vehi- cle’s interior according to the angle and intensity of the sun’s rays, the outside tem- perature and the selected temperature. You can operate the climate control sys- tem in either the automatic or manual mode.


Controls in detail 4-zone automatic climate control


Warning!


When operating the climate control, the air that enters the passenger compartment through the air vents can be very hot or very cold (depending on the set temperature). This may cause burn or frostbite to unpro- tected skin in the immediate area of the air vents. Always keep sufficient distance be- tween unprotected parts of the body and the air vents. If necessary, use the air distribu- tion controls (컄 page 222) or (컄 page 223) to direct the air to air vents in the vehicle in- terior that are not in the immediate area of unprotected skin.


224


Nearly all dust particles, pollutants and odors are filtered out before outside air en- ters the passenger compartment through the air distribution system. The air conditioning will not engage (no cooling) if the A/C mode (컄 page 234) is deactivated.


Warning!


Follow the recommended settings for heat- ing and cooling given on the following pag- es. Otherwise the windows could fog up, impairing visibility and endangering you and others.


i Severe conditions (e.g. strong air pollution) may require replacement of the filter before its scheduled interval. A clogged filter will reduce the air volume to the interior. If the vehicle interior is hot, ventilate the interior before driving off, see “Summer opening fea- ture” (컄 page 239). The climate control will then adjust the interior temperature to the set value much faster. Keep the air intake grille in front of the wind- shield free of snow and debris. Do not obstruct air flow by placing objects on the air flow-through exhaust slots below the rear window.


Controls in detail 4-zone automatic climate control


Deactivating the climate control system


Warning!


When the climate control is switched off, the outside air supply and circulation are also switched off. Only choose this setting for a short time. Otherwise the windows could fog up, impairing visibility and endangering you and others.


Deactivating 왘 Press button ´ (컄 page 222) or


(컄 page 223) until the display 4 (컄 page 222) or (컄 page 223) is cleared.


225


Controls in detail 4-zone automatic climate control


Reactivating 왘 Make sure the ignition is switched on. 왘 Press button ´ (컄 page 222) or


(컄 page 223) again. The previous settings are once again in effect.


i To switch the system on, you can also press another button, with the exception of 1 (USA only) (컄 page 222) or F and T (Canada only) (컄 page 223).


226


Operating the climate control system in automatic mode


i When operating the climate control system in automatic mode, you will only rarely need to adjust the temperature, air volume and air distri- bution. In automatic mode, cooling with dehumidify is switched on. This function can be switched off.


Warning!


If you switch off the cooling function the windows can fog up more quickly. Window fogging may impair visibility and endanger you and others.


i You can switch the automatic climate con- trol system on and off for each side of the pas- senger compartment as desired.


Activating 왘 Press one button U (컄 page 222) or


(컄 page 223) while the engine is run- ning. The indicator lamp on the button comes on. AUTO appears in the display 4 (컄 page 222) or (컄 page 223). The air volume and air distribution are adjusted automatically. 왘 Use temperature rocker switches 3 and 5 (컄 page 222) or (컄 page 223) to separately adjust the air tempera- ture on each side of the passenger compartment. The temperature of the vehicle interior is adjusted automatically.


Deactivating 왘 Press button ˜ or Q


(컄 page 222) or (컄 page 223). The AUTO indicator in the display 4 (컄 page 222) or (컄 page 223) goes out. The automatic function for air vol- ume is switched off, and air volume is controlled according to the desired set- ting.


or 왘 Turn air distribution control 1 or 7 (컄 page 222) or (컄 page 223) on each side of the passenger compartment to the desired symbol. The indicator lamp on the correspond- ing button goes out. Automatic air dis- tribution is switched off in the corresponding zone, and air distribu- tion is controlled according to the de- sired position. The automatic air volume remains switched on.


Setting the temperature


Use temperature control rocker switches 3 and 5 (컄 page 222) or (컄 page 223) to separately adjust the air temperature on each side of the passenger compartment. You should raise or lower the temperature setting in small incre- ments, preferably starting at 72°F (22°C). The adjusted temperature appears in the display 4 (컄 page 222) or (컄 page 223). The climate control will adjust to the set temperature as fast as possible.


i You can also adjust the temperature in the rear passenger compartment (컄 page 235).


i When operating the climate control system in automatic mode, you will only rarely need to adjust the temperature, air volume and air distri- bution.


Controls in detail 4-zone automatic climate control


Increasing 왘 Push top of temperature control rocker switch 3 and/or 5 (컄 page 222) or (컄 page 223). The climate control system will corre- spondingly adjust the interior air tem- perature.


Decreasing 왘 Push bottom of temperature control


rocker switch 3 and/or 5 (컄 page 222) or (컄 page 223). The climate control system will corre- spondingly adjust the interior air tem- perature.


227


Controls in detail 4-zone automatic climate control


Adjusting air distribution


Use the air distribution controls 1 and 7 (컄 page 222) or (컄 page 223) to separate- ly adjust the air distribution on each side of the passenger compartment. The following symbols are located on the controls:


Symbol Function a Directs air through the cockpit (Canada only), center, side and rear passenger compartment air vents


Z Directs air to the windshield and through the side air vents X Directs air into the entire vehi-


cle interior


Y Directs air to the footwells


228


왘 Turn air distribution controls 1


and 7 (컄 page 222) or (컄 page 223) on each side of the passenger compart- ment to the desired symbol. The indicator lamp on the correspond- ing button goes out and the automatic air distribution is switched off for the corresponding side. The air distribution is controlled according to the thumb- wheel setting.


i You can also turn the air distribution control to a position between two symbols.


Closing the cockpit air vent (Canada only) and center air vents 왘 Turn thumbwheels 1 and 5


(컄 page 220) downward. The cockpit air vent 3 and the center air vents 2 and 4 are closed.


Opening the side air vents 왘 Turn thumbwheels 8 and a


(컄 page 220) upward. The side air vents 7 and b are open.


Opening the cockpit air vent (Canada only) and center air vents 왘 Turn thumbwheels 1 and 5


(컄 page 220) upward. The cockpit air vent 3 and the center air vents 2 and 4 are open.


Closing the side air vents 왘 Turn thumbwheels 8 and a


(컄 page 220) downward. The side air vents 7 and b are closed.


Adjusting air volume


Front defroster


Use buttons U (컄 page 222) or (컄 page 223) for automatic mode or air volume buttons ˜ or Q (컄 page 222) or (컄 page 223) to adjust air volume manually. Nine blower speeds are available. 왘 Press button ˜ to decrease or


button Q to increase air volume to the desired level. The AUTO indicator for air volume in the display 4 (컄 page 222) or (컄 page 223) goes out. The selected blower speed is shown in the display 4. Automatic air distribution remains switched on. The indicator lamps on the U but- tons remain lit.


You can use this setting to defrost the windshield, for example if it is iced up. You can also defog the windshield and the windows.


i Keep this setting selected only until the windshield or the windows are clear again.


Activating 왘 Press button 0 or P (컄 page 222) or (컄 page 223). The indicator lamp on the button comes on. Display 4 (컄 page 222) or (컄 page 223) is cleared.


Controls in detail 4-zone automatic climate control


The air conditioning switches automatically to the following functions: 앫 cooling on to dehumidify 앫 maximum blowing and heating power


(depends on cooling temperature)


앫 air flows onto the windshield and the


front windows


앫 the air recirculation mode is switched


off


i If you have switched on the defrost function using the 0 or P button, you cannot make any other settings.


Deactivating 왘 Press button 0 or P


(컄 page 222) or (컄 page 223) again. The indicator lamp on the button goes out. Defrosting is turned off. The previous settings are once again in effect.


i The cooling remains switched on.


229


Controls in detail 4-zone automatic climate control


Windshield fogged on the outside


i Keep this setting selected only until the windshield is clear again. 왘 Switch the windshield wipers on


(컄 page 58).


If the automatic mode of the climate con- trol is switched off: 왘 Turn air distribution controls 1 and 7


to a or Y (컄 page 222) or (컄 page 223).


230


Deactivating 왘 Press button e (컄 page 222) again. MAX COOL disappears in the display 4 (컄 page 222). The previous settings are once again in effect.


i To switch the maximum cooling function off, you can also press button ´, U, 0 or 1 (컄 page 222).


Maximum cooling MAX COOL (USA only)


You can use this setting to provide the fast- est possible cooling of the vehicle interior (when windows and tilt/sliding sunroof or tilt/sliding panel* are closed).


Activating 왘 Press button e (컄 page 222).


MAX COOL appears in the display 4 (컄 page 222).


The air conditioning switches automatically to the following functions: 앫 maximum cooling 앫 maximum blowing power 앫 the air recirculation mode is switched


on


Air recirculation mode


Switch to air recirculation mode to prevent unpleasant odors from entering the vehicle from the outside (e.g. before driving through a tunnel). This setting cuts off the intake of outside air and recirculates the air in the passenger compartment.


Warning!


Fogged windows impair visibility, endanger- ing you and others. If the windows begin to fog on the inside, switching off the air recirculation mode immediately should clear interior window fogging. If interior window fogging persists, make sure the air conditioning (컄 page 233) is activated, or press button P or 0.


Activating 왘 Press button , (컄 page 222) or


(컄 page 223). The indicator lamp on the button comes on.


i The air recirculation mode is activated auto- matically at high outside temperatures and if the concentration of carbon monoxide (CO) and ni- trogen oxide in the outside air increases, for ex- ample in a tunnel. The indicator lamp on button , is not lit when the air recirculation mode is automatically switched on. A quantity of outside air is added after approxi- mately 30 minutes.


Controls in detail 4-zone automatic climate control


Deactivating 왘 Press button , (컄 page 222) or


(컄 page 223) again. The indicator lamp on the button goes out.


i The air recirculation mode is deactivated au- tomatically: 앫 after 5 minutes if the outside temperature is


below approximately 41°F (5°C)


앫 after 5 minutes if the air conditioning is


turned off


앫 after 30 minutes if the outside temperature


is above approximately 41°F (5°C)


231


Controls in detail 4-zone automatic climate control


Air recirculation mode with conve- nience closing or opening feature


Warning!


Never operate the windows and tilt/sliding sunroof or tilt/sliding panel* if there is the possibility of anyone being harmed by the opening or closing procedure.


In the event that the procedure causes po- tential danger, the closing of the windows can be immediately halted by pressing or pulling the respective window switch. The closing of the tilt/sliding sunroof can be im- mediately halted by moving the switch for the tilt/sliding sunroof in any direction.


Vehicles with panorama roof*: When using the air recirculation mode with convenience closing feature, should the up- ward movement of a window be blocked by some obstruction including but not limited to arms, hands, fingers, etc., the automatic reversal feature will not operate. In the event that the procedure causes po- tential danger,


232


the closing of the windows and tilt/sliding panel can be immediately halted by releas- ing the , button. The closing of the windows and the tilt/slid- ing sunroof can be reversed by again press- ing and holding the , button.


Convenience closing 왘 Press button , (컄 page 222) for


approximately 2 seconds. The windows and tilt/sliding sunroof will close. You can release button , once the closing procedure has begun. The windows and tilt/sliding sunroof continue closing until they are fully closed. The indicator lamp on the but- ton comes on. The air recirculation mode is activated.


Convenience opening 왘 Press button , for approximately


2 seconds. The windows and tilt/sliding sunroof will return to their previous posi- tion.You can release button , once the opening procedure has begun. The windows and tilt/sliding sunroof con- tinue opening until they have reached their previous position. The indicator lamp on the button goes out. The air re- circulation mode is deactivated.


i A window or tilt/sliding sunroof will only re- turn to its previous position if it has not been moved to another position using the respective window switch or tilt/sliding sunroof switch af- ter it was closed with button ,. A window or tilt/sliding sunroof that has been moved will remain in its current position if button , is used to reopen the remaining windows or tilt/sliding sunroof.


Vehicles with panorama roof* Convenience closing: 왘 Press and hold button ,


(컄 page 222) or (컄 page 223) until the windows and the tilt/sliding panel are closed or have reached the desired po- sition. The indicator lamp on the button comes on. The air recirculation mode is activated.


Convenience opening: 왘 Press and hold button , until the windows and the tilt/sliding panel are opened or have reached the desired position. The indicator lamp on the but- ton goes out. The air recirculation mode is deactivated.


Controls in detail 4-zone automatic climate control


Combination filter with pollutant-sensi- tive air-recirculation mode The combination filter reduces pollutants and unpleasant odors in the outside air. The pollutant-sensitive air-recirculation mode automatically switches off the sup- ply of outside air when pollutants are de- tected in the air.


i The pollutant-sensitive air-recirculation mode is not possible if you have switched off the air conditioning or if the temperature falls below 41°F (5°C).


Air conditioning


The cooling function, only operational when the engine is running, cools the vehi- cle interior down to the selected tempera- ture. The cooling function also dehumidifies the air in the vehicle interior, thus preventing the windows from fogging up.


i Condensation may drip out from underneath the vehicle. This is normal and not an indication of a malfunction.


Warning!


If you turn off the cooling function, the vehicle will not be cooled when weather conditions are warm. The windows can fog up more quickly. Window fogging may impair visibility and endanger you and others.


233


Controls in detail 4-zone automatic climate control


Deactivating It is possible to deactivate the air condi- tioning (cooling) function of the climate control system. The air in the vehicle will then no longer be cooled or dehumidified. 왘 Press button 2 (컄 page 222) or


(컄 page 223). The indicator lamp on the button goes out.


Activating Moist air can fog up the windows. You can dehumidify the air with the air condition- ing. 왘 Press button 2 (컄 page 222) or


(컄 page 223) again. The indicator lamp on the button comes on.


The air conditioning uses the refrigerant R134a. This refrigerant is free of CFCs which are harmful to the ozone layer.


234


! If the air conditioning cannot be turned on again, this indicates that the air conditioning is losing refrigerant. The compressor has turned it- self off. Have the air conditioning checked at the nearest authorized Mercedes-Benz Center.


Residual heat and ventilation (Canada only)


With the engine switched off, it is possible to continue to heat or ventilate the interior for up to 30 minutes. This feature makes use of the residual heat produced by the engine.


i If you switch on the residual heat function when temperatures are high, only the ventilation will be switched on.


i Regardless of the selected air volume, the blower operates at low speed.


i How long the system will provide heating de- pends on 앫 the coolant temperature 앫 the temperature set by the operator The blower will run at speed setting 1 regardless of the air distribution control setting.


Rear climate control


The rear climate control is adjusted via the front climate control panel (컄 page 222) or (컄 page 223) or the rear climate control panel. The rear climate control panel is located in the rear center console.


Activating 왘 Switch off the ignition. 왘 Press button T (컄 page 223).


REST in the display 4 (컄 page 223) comes on.


Deactivating 왘 Press button T (컄 page 223) again.


REST in the display 4 (컄 page 223) goes out.


i The residual heat is automatically turned off: 앫 when the ignition is switched on 앫 after about 30 minutes 앫 if the battery voltage drops 앫 if the coolant temperature is too low


Controls in detail 4-zone automatic climate control


1 Left rear center air vent, adjustable 2 Right rear center air vent, adjustable 3 Thumbwheel for air volume control


for right rear center air vent


4 Temperature rocker switch, right 5 Display 6 Temperature rocker switch, left 7 Thumbwheel for air volume control


for left rear center air vent


Setting the temperature Use temperature control rocker switches 4 and 6 to separately adjust the air temperature on each side of the rear passenger compartment.


i You can also adjust the rear temperature us- ing the front climate control panel (컄 page 222) or (컄 page 223).


235


Controls in detail 4-zone automatic climate control


You should raise or lower the temperature setting in small increments, preferably starting at 72°F (22°C). The adjusted tem- perature appears in the display 5. The rear climate control will adjust to the set temperature as fast as possible.


1 Temperature, left 2 Temperature, right 왘 Adjust the temperature to the desired setting for each side of the passenger compartment using the left and right temperature buttons. The temperature in the rear passenger compartment is adjusted automatical- ly.


i The rear climate control will not cool the air when the air conditioning is switched off (컄 page 234).


236


Adjusting air distribution 왘 Move the slider for the left center air vent 1 or right center air vent 2 to the left, right, up, or down. The air flow is directed in the corresponding direction.


i For draft-free ventilation, move sliders for the center air vents 1 and 2 (컄 page 235) up- ward.


Adjusting air volume 왘 Turn thumbwheel 3 or 7


(컄 page 235) up or down. The air volume is increased or decreased.


Adjusting the rear settings with the front control panel You can adjust the temperature for the rear climate control from the front climate control panel.


왘 Press button 5 or ™


(컄 page 222) or (컄 page 223). The display switches over.


1 Rear climate control display 왘 Set the desired temperature for the rear passenger compartment using temperature rocker switches 4 and 6 (컄 page 235). After approximately 5 seconds after the last adjustment, the display switch- es back to its standard display.


i You can also press button 5 or ™ (컄 page 222) or (컄 page 223) once more to switch back to the standard display.


왔 Power windows Opening and closing the windows


The windows are opened and closed elec- trically. The switches for all of the windows are on the driver’s door. The switches for the respective windows are on the front passenger door and the rear doors.


1 Left front window 2 Right front window 3 Right rear window 4 Left rear window


Warning!


When closing the windows, make sure that there is no danger of anyone being harmed by the closing procedure.


The closing of the windows can be immedi- ately halted by releasing the switch or, if switch was pulled past the resistance point and released, by either pressing or pulling the respective switch.


The windows are equipped with the ex- press-close and automatic reversal func- tion. If the window encounters an obstruction that blocks its path in a circum- stance where you pulled the switch past the resistance point and released it to close the window, the automatic reversal function will stop the window and open it slightly.


If the window encounters an obstruction that blocks its path in a circumstance where you are closing the window by pulling and holding the switch, by pressing and holding button ‹ on the SmartKey, by pressing


Controls in detail Power windows


and holding the lock button (vehicles with KEYLESS-GO*) on an outside door handle, or by pressing and holding button , on the climate control panel, the automatic re- versal function will not operate.


When leaving the vehicle, always remove the SmartKey or SmartKey with KEYLESS-GO* from the starter switch, take it with you, and lock the vehicle. Do not leave children unat- tended in the vehicle, or with access to an unlocked vehicle. A child’s unsupervised ac- cess to a vehicle could result in an accident and/or serious personal injury.


i You can also open or close the windows us- ing the SmartKey, see “Summer opening fea- ture” (컄 page 239) and “Convenience closing feature” (컄 page 240). Depending on current position, the windows may also open or close when the air recirculation button , in the control panel of the climate control (컄 page 206), (컄 page 222) and (컄 page 223) is pressed and held.


237


Controls in detail Power windows


i Operating the windows from the rear is not possible if you activate the override switch (컄 page 95).


Warning!


Warning!


i With the SmartKey in starter switch position 0 or removed from the starter switch, the windows can be operated: 앫 until you open the driver’s or front passen-


ger’s door


앫 for at least 5 minutes 왘 Switch on the ignition (컄 page 37).


Opening the windows 왘 Press switch 1 to 4 to the resistance


point. The corresponding window will move downwards until you release the switch.


Closing the windows 왘 Pull switch 1 to 4 to the resistance


point. The corresponding window will move upwards until you release the switch.


238


If you pull and hold the switch up when clos- ing the window, and upward movement of the window is blocked by some obstruction including but not limited to arms, hands, fin- gers, etc., the automatic reversal will not op- erate.


Fully opening the windows (Express-open) 왘 Press switch 1 to 4 past the resis-


tance point and release. The corresponding window opens com- pletely.


Fully closing the windows (Express-close) 왘 Pull switch 1 to 4 past the resis-


tance point and release. The corresponding window closes com- pletely.


Driver’s door only: If within 5 seconds switch is again pulled past the resistance point and released, the automatic reversal will not operate.


! If the upward movement of the window is blocked during the closing procedure, the win- dow will stop and open slightly. Remove the obstruction, pull the respective pow- er window switch again past the resistance point and release. If the window still does not close when there is no obstruction, pull and hold the respective pow- er window switch. The window will then close without the obstruction sensor function.


Stopping windows during Express-op- eration 왘 Press or pull the respective power win-


dow switch again.


Synchronizing power windows


Summer opening feature


If the weather is warm, you can ventilate the vehicle before driving off by simulta- neously: 앫 opening the windows 앫 opening the tilt/sliding sunroof or


tilt/sliding panel*


앫 turning on the seat ventilation* for the


driver’s seat


i The seat ventilation* for the driver’s seat is automatically set to the highest level if activated via summer opening feature.


The power windows must be synchronized 앫 after the battery has been disconnect-


ed


앫 if the power windows cannot be fully


opened (Express-open) or closed (Express-close)


Synchronizing 왘 Close all doors. 왘 Switch on the ignition (컄 page 37). 왘 Pull switch 1 to 4 until the windows


are completely closed.


왘 Hold on to switches 1 to 4 for ap-


proximately 1 second.


The power windows are synchronized.


Controls in detail Power windows


왘 Aim transmitter eye of the SmartKey or


SmartKey with KEYLESS-GO* at the driver’s outside door handle. The SmartKey or SmartKey with KEYLESS-GO* must be in close proxim- ity to the driver’s outside door handle.


Vehicles without panorama roof* 왘 Press and hold button Œ until the windows and the tilt/sliding sunroof have reached the desired position.


왘 Release button Œ to interrupt pro-


cedure.


239


Vehicles with KEYLESS-GO*: 왘 Press and hold the lock button on an outside door handle (컄 page 65) until the windows, the tilt/sliding sunroof or tilt/sliding panel* are completely closed.


왘 Release the lock button on the outside


door handle to interrupt procedure.


Controls in detail Power windows


Vehicles with panorama roof* If roller sunblinds are closed: 왘 Press and hold button Œ until the


windows and the roller sunblinds begin to open after approximately 1 second. 왘 With the windows and roller sunblinds


fully opened, press and hold button Œ again. The tilt/sliding pan- el of the panorama roof tilts and opens. 왘 Release button Œ to interrupt pro-


cedure.


If roller sunblinds are open: 왘 Press and hold button Œ. The win- dows move down and the tilt/sliding panel tilts and opens after approxi- mately 1 second.


왘 Release button Œ to interrupt pro-


cedure.


240


Convenience closing feature


When you lock the vehicle, you can close the windows, tilt/sliding sunroof or tilt/sliding panel* simultaneously. 왘 Aim transmitter eye of the SmartKey or


SmartKey with KEYLESS-GO* at the driver’s outside door handle (컄 page 239). The SmartKey or SmartKey with KEYLESS-GO* must be in close proximity to the driver’s out- side door handle.


왘 Press and hold button ‹ until the windows, the tilt/sliding sunroof or tilt/sliding panel* are completely closed.


Vehicles with panorama roof*: 왘 Press and hold button ‹ again. The


roller sunblinds close.


왘 Release button ‹ to interrupt pro-


cedure.


Warning!


When closing the windows and the tilt/slid- ing sunroof or tilt/sliding panel*, make sure that there is no danger of anyone being harmed by the closing procedure.


If potential danger exists, proceed as fol- lows: 앫 Release button ‹ to stop the closing


procedure. To open, press and hold button Œ. To continue the closing procedure after making sure that there is no danger of anyone being harmed by the closing procedure, press and hold button ‹.


Vehicles with KEYLESS-GO*: 앫 Release the lock button (컄 page 65) on the outside door handle to stop the clos- ing procedure.


앫 Immediately pull on the same outside door handle and hold firmly. The win- dows and the tilt/sliding sunroof or tilt/sliding panel* will open for as long as the door handle is held but the door not opened.


Controls in detail Power windows


241


Controls in detail Power tilt/sliding sunroof


Opening and closing the power tilt/sliding sunroof


The tilt/sliding sunroof is opened and closed electrically. The switch for the tilt/sliding sunroof is on the overhead con- trol panel.


With the sunroof closed or tilted open, a screen can be slid into the sunroof opening to guard against sun rays. When sliding the sunroof open, the screen will also retract.


Sunroof switch 1 Push back to slide sunroof open 2 Push forward to slide sunroof closed 3 Push up to raise sunroof at rear 4 Pull down to lower sunroof at rear


242


Warning!


When closing the tilt/sliding sunroof, make sure there is no danger of anyone being harmed by the closing procedure.


The opening/closing procedure of the tilt/sliding sunroof can be immediately halt- ed by releasing the switch or, if the switch was moved past the resistance point and re- leased, by moving the switch in any direc- tion.


The tilt/sliding sunroof is made out of glass. In the event of an accident, the glass may shatter. This may result in an opening in the roof.


In a vehicle rollover, occupants not wearing their seat belts or not wearing them properly may be thrown out of the opening. Such an opening also presents a potential for injury for occupants wearing their seat belts prop- erly as entire body parts or portions of them may protrude from the passenger compart- ment.


i When the tilt/sliding sunroof is open, reso- nance noises may result in addition to the usual wind noises. They are caused by minimal pres- sure changes in the passenger compartment. To reduce or eliminate these noises, change the po- sition of the tilt/sliding sunroof or open a side window slightly.


i You can also open or close the tilt/sliding sunroof using the SmartKey, see “Summer open- ing feature” (컄 page 239) or see “Convenience closing feature” (컄 page 240). Depending on current position, the tilt/sliding sunroof may also open or close when the air re- circulation button , in the control panel of the climate control (컄 page 206), (컄 page 207), (컄 page 222) or (컄 page 223) is pressed and held. 왘 Switch on the ignition (컄 page 37).


When leaving the vehicle, always remove the SmartKey or the SmartKey with KEYLESS-GO* from the starter switch, take it with you, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. A child’s unsupervised access to a vehicle could re- sult in an accident and/or serious personal injury.


! To avoid damaging the seals, do not trans- port any objects with sharp edges which can stick out of the tilt/sliding sunroof. Do not open the tilt/sliding sunroof if there is snow or ice on the roof, as this could result in malfunctions. The tilt/sliding sunroof can be opened or closed manually should an electrical malfunction occur (컄 page 439).


! Please keep in mind that weather conditions can sometimes change rapidly. Make sure to close the tilt/sliding sunroof when leaving the vehicle. If water enters the vehicle interior, vehi- cle electronics could be damaged which is not covered by the Mercedes-Benz Limited Warranty.


Controls in detail Power tilt/sliding sunroof


Opening and closing the power tilt/sliding sunroof 왘 To open, close, raise or lower the


tilt/sliding sunroof, move the sunroof switch to resistance point in the re- quired direction of arrows 1 to 4. Release the sunroof switch when the tilt/sliding sunroof has reached the de- sired position.


Fully opening (Express-open) and clos- ing (Express-close) the power tilt/slid- ing sunroof 왘 To open or close the tilt/sliding sun-


roof, move the sunroof switch past the resistance point in direction of arrow 1 to 2 and release. The tilt/sliding sunroof opens or closes completely.


243


Controls in detail Power tilt/sliding sunroof


Stopping the power tilt/sliding sunroof during Express-operation 왘 Move the sunroof switch in any direc-


tion.


i If the movement of the tilt/sliding sunroof is blocked during the Express-close procedure, the tilt/sliding sunroof will stop and reopen slightly.


Synchronizing the power tilt/sliding sunroof


왘 Remove the respective fuse from the


main fuse box (컄 page 470).


The tilt/sliding sunroof must be synchro- nized 앫 after the battery has been disconnected or discharged


앫 after the tilt/sliding sunroof has been


closed manually (컄 page 439)


앫 after a malfunction 앫 if the tilt/sliding sunroof does not open


smoothly


왘 Reinsert the fuse in the main fuse box. 왘 Switch on the ignition (컄 page 37). 왘 Move and hold the sunroof switch in di- rection of arrow 3 until the tilt/sliding sunroof is fully raised at the rear. Keep holding the sunroof switch in di- rection of arrow 3 for approximately 1 second.


왘 Check the Express-open feature


(컄 page 243). If the tilt/sliding sunroof opens com- pletely, the roof is synchronized. Other- wise repeat the above steps.


244


왔 Panorama roof with power tilt/sliding panel* Opening and closing the roller sunblinds for the panorama roof with power tilt/sliding panel


The tilt/sliding panel and the front and rear roller sunblinds are opened and closed electrically. The switch for the tilt/sliding panel and the roller sunblinds is on the overhead control panel. An addi- tional switch for the roller sunblinds is in the rear passenger compartment. The roller sunblinds only operate with the tilt/sliding panel closed. The front and rear roller sunblind cannot be operated individ- ually.


Roof panel switch 1 Open roller sunblinds 2 Close roller sunblinds


Controls in detail Panorama roof with power tilt/sliding panel*


Roller sunblinds switch, rear 1 Open roller sunblinds 2 Close roller sunblinds 왘 Switch on the ignition (컄 page 37).


Opening and closing the roller sun- blinds 왘 To open or close the roller sunblinds, move the roof panel/roller sunblinds switch to the resistance point in the re- quired direction of arrow 1 or 2. Release the roof panel/roller sunblinds switch when the roller sunblinds have reached the desired position.


컄컄


245


Controls in detail Panorama roof with power tilt/sliding panel*


컄컄


Warning!


Opening and closing the panorama roof with power tilt/sliding panel


Warning!


When closing the roller sunblinds, make sure that no one is in danger of being injured by the closing procedure. The closing of the roller sunblinds can be immediately halted by releasing the switch.


The tilt/sliding panel is opened and closed electrically. The switch for the tilt/sliding panel is on the overhead control panel. The tilt/sliding panel only operates with the roller sunblinds opened.


Fully opening the roller sunblinds (Ex- press-open) 왘 Move the roof panel/roller sunblinds switch past the resistance point in di- rection of arrow 1 and release. The roller sunblinds opens completely.


Stopping the roller sunblinds during Express-operation 왘 Move the roof panel/roller sunblinds


switch in any direction.


246


Roof panel switch 1 Push back to slide roof panel open 2 Push forward to slide roof panel closed 3 Push up to raise roof panel 4 Pull down to lower roof panel


When opening or closing the tilt/sliding pan- el, make sure that there is no danger of any- one being harmed by the opening or closing procedure.


The opening procedure of the tilt/sliding panel can be immediately halted by releas- ing the switch or, if the switch was moved past the resistance point and released, by moving the switch in any direction.


The closing procedure of the tilt/sliding panel can be immediately halted by releas- ing the switch.


The panorama roof with power tilt/sliding panel is made out of glass. In the event of an accident, the glass may shatter. This may re- sult in an opening in the roof.


Controls in detail Panorama roof with power tilt/sliding panel*


i You can also open or close the tilt/sliding panel using the SmartKey (summer open- ing/convenience closing feature) (컄 page 239) or (컄 page 240). Depending on current position, the tilt/sliding panel may also open or close when the air recir- culation button , in the control panel of the climate control (컄 page 206), (컄 page 207), (컄 page 222) or (컄 page 223) is pressed and held. 왘 Switch on the ignition (컄 page 37).


In a vehicle rollover, occupants not wearing their seat belts or not wearing them properly may be thrown out of the opening. Such an opening also presents a potential for injury for occupants wearing their seat belts prop- erly as entire body parts or portions of them may protrude from the passenger compart- ment.


When leaving the vehicle, always remove the SmartKey or the SmartKey with KEYLESS-GO* from the starter switch, take it with you, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. A child’s unsupervised access to a vehicle could re- sult in an accident and/or serious personal injury.


! To avoid damaging the seals, do not trans- port any objects with sharp edges which can stick out of the tilt/sliding panel.


Do not open the tilt/sliding panel if there is snow or ice on the roof, as this could result in malfunc- tions. The tilt/sliding panel can be opened or closed manually should an electrical malfunction occur (컄 page 439). ! Please keep in mind that weather conditions can sometimes change rapidly. Make sure to close the tilt/sliding panel when leaving the ve- hicle. If water enters the vehicle interior, vehicle electronics could be damaged which is not cov- ered by the Mercedes-Benz Limited Warranty.


i When the tilt/sliding panel is open, reso- nance noises may result in addition to the usual wind noises. They are caused by minimal pres- sure changes in the passenger compartment. To reduce or eliminate these noises, change the po- sition of the tilt/sliding panel or open a side win- dow slightly.


247


Controls in detail Panorama roof with power tilt/sliding panel*


Opening and closing the panorama roof with power tilt/sliding panel 왘 To open, close, raise, or lower the


tilt/sliding panel, move the roof panel switch to resistance point in the re- quired direction of arrows 1 to 4. Release the roof panel switch when the tilt/sliding panel has reached the de- sired position.


Fully opening (Express-open) the pan- orama roof with power tilt/sliding pan- el 왘 Move the roof panel switch past the re- sistance point in direction of arrow 1 and release. The tilt/sliding panel opens completely.


Stopping the panorama roof with power tilt/sliding panel during Express-open 왘 Move the roof panel switch in any di-


rection.


248


Synchronizing the panorama roof with power tilt/sliding panel


The tilt/sliding panel must be synchronized 앫 after the battery has been disconnected or discharged


앫 after the tilt/sliding panel has been


closed manually (컄 page 439)


앫 after a malfunction 앫 if the tilt/sliding panel does not open


smoothly


왘 Remove the fuse from the main fuse


box (컄 page 469).


왘 Reinsert the fuse in the main fuse box. 왘 Switch on the ignition (컄 page 37). 왘 Move and hold the roof panel switch in


direction of arrow 2 until the roller sunblinds are fully closed.


왘 Keep holding the roof panel switch in direction of arrow 2 for approximately 1 second.


왘 Move and hold the roof panel switch in


direction of arrow 1 until the roller sunblinds are fully opened.


왘 Keep holding the roof panel switch in direction of arrow 1 for approximately 1 second.


왘 Move and hold the roof panel switch in direction of arrow 3 until the tilt/slid- ing panel is fully raised.


왘 Keep holding the roof panel switch in direction of arrow 3 for approximately 1 second.


왘 Move and hold the roof panel switch in direction of arrow 2 until the tilt/slid- ing panel is fully closed.


왘 Keep holding the roof panel switch in direction of arrow 2 for approximately 1 second.


왘 Check the Express-open feature of the


tilt/sliding panel (컄 page 248). If the tilt/sliding panel opens com- pletely, the roof is synchronized. Other- wise repeat the above steps.


왔 Driving systems The driving systems of your vehicle are de- scribed on the following pages: 앫 Cruise control and Distronic*, with


which the vehicle can maintain a preset speed


앫 Airmatic DC adjusts the vehicle sus-


Loading...
x