Login- Download PDF Manual
-
2010-05-20T13:33:46+02:00 - Seite 216
Version: 3.0.3.6216 Displays and operation
Vehicle equipment
i This manual describes all the standard and optional equipment of your vehicle which was available at the time of purchase. Country-specific differences are possible. Bear in mind that your vehicle may not feature all functions described here. This also refers to safety-related systems and functions.
Important safety notes
You will find an illustration of the instrument cluster in the "At a glance" section (Y page 28). G Warning A driver's attention to the road and traffic conditions must always be his/her primary focus when driving. For your safety and the safety of others, selecting features through the multifunction steering wheel should only be done by the driver when traffic and road conditions permit it to be done safely. Bear in mind that at a speed of just 30 mph (approximately 50 km/h ), your vehicle is covering a distance of 44 feet (approximately 14 m) every second. G Warning! No messages will be displayed if either the instrument cluster or the multifunction display is inoperative. As a result, you will not be able to see information about your driving conditions, such as Rspeed Routside temperature Rwarning/indicator lamps Rmalfunction/warning messages Rfailure of any systems Driving characteristics may be impaired.
If you must continue to drive, do so with added caution. Contact an authorized Mercedes- Benz Center as soon as possible. G Warning Malfunction and warning messages are only indicated for certain systems and are intentionally not very detailed. The malfunction and warning messages are simply a reminder with respect to the operation of certain systems. They do not replace the owner's and/or driver's responsibility to maintain the vehicle's operating safety. Have all required maintenance and safety checks performed on the vehicle. Bring the vehicle to an authorized Mercedes-Benz Center to address the malfunction and warning messages.
Displays and operation Coolant temperature gauge G Warning Driving when your engine is overheated can cause some fluids which may have leaked into the engine compartment to catch fire. You could be seriously burned. Steam from an overheated engine can cause serious burns which can occur just by opening the engine hood. Stay away from the engine if you see or hear steam coming from it. Stop the vehicle in a safe location away from other traffic. Turn off the engine, get out of the vehicle and do not stand near the vehicle until the engine has cooled down.
The coolant temperature gauge is in the instrument cluster on the right-hand side. Under normal operating conditions and with the specified coolant level, the coolant temperature may rise to 248 ‡ (120 †). ! If the coolant temperature is too high a
display message is shown.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 217
Version: 3.0.3.6Displays and operation 217
If the coolant temperature rises above 248 ‡(120 †), do not drive any further as this could damage the engine.
Tachometer The red band in the tachometer indicates the engine's overrevving range. ! Do not drive in the overrevving range, as
this could damage the engine.
The fuel supply is interrupted to protect the engine when the red band is reached.
Outside temperature display The outside temperature display is in the multifunction display. G Warning! The outside temperature indicator is not designed to serve as an ice-warning device and is therefore unsuitable for that purpose. Indicated temperatures just above the freezing point do not guarantee that the road surface is free of ice. The road may still be icy, especially in wooded areas or on bridges.
Changes in the outside temperature are displayed after a short delay.
Speedometer with segments The segments in the speedometer indicate which speed range is available. Cruise control mode: The segments light up from the stored speed to the maximum speed. DISTRONIC PLUS mode: One or two segments around the stored speed light up.
Operating the on-board computer The on-board computer is activated as soon as you turn the SmartKey to position 1 in the ignition lock. You can control the multifunction display and the settings in the on-board computer using the buttons on the multifunction steering wheel.
: Multifunction display
; ~6
Makes/accepts or rejects/ends a call WX Adjusts the volume or operates the RACETIMER in AMG vehicles Mute
= ?
Activates voice control; see the separate operating instructions
? %Press briefly:
Back Deactivates voice control Hides display messages
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 218
Version: 3.0.3.6218 Displays and operation
: Text field ; Menu bar = Drive program indicator ? Gear indicator A Outside temperature or speed X To display menu bar ;: press the =
or ; button on the steering wheel.
i In AMG vehicles, the status indicator
differs from the display shown here (Y page 155).
Further information on the gear indicator (Y page 155).
%Press and hold: Selects the standard display
A =;
Calls up the menu and menu bar 9:Press briefly: Selects the submenu or scrolls through lists In the Audio menu: selects a stored station, an audio track or a video scene In the Tel (telephone) menu: switches to the phone book and selects a name or telephone number 9:Press and hold: In the Audio menu: selects the previous/next station or selects an audio track or a video scene using rapid scrolling In the Tel (telephone) menu: starts rapid scrolling through the phone book
Confirms selections and hides display messages In the Tel (telephone) menu: switches to the phone book and starts dialing
Multifunction display To activate the multifunction display: Rswitch on the ignition Rswitch on the lights Ropen the driver's door Values and settings as well as display messages are shown in the multifunction display.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 219
Version: 3.0.3.6Menus and submenus
219
Menus and submenus Menu overview The number of menus shown depends on the optional equipment in the vehicle.
Function Trip menu (Y page 220) AMG menu in AMG vehicles (Y page 221) Navi menu (navigation instructions) (Y page 224) Audio menu (Y page 225) Tel menu (telephone) (Y page 226) DriveAssist menu (assistance) (Y page 227) Serv. menu (Y page 229) Rcall up display messages (Y page 234) Rtire pressure loss warning system (Canada only) (Y page 355) Rtire pressure monitor (Y page 357) RASSYST PLUS service interval display (Y page 313) Settings menu (Y page 229)
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 220
Version: 3.0.3.6220 Menus and submenus
Rthe ignition has been switched off for more
than 4 hours.
R999 hours have been exceeded. R9999 miles have been exceeded. The From Reset trip computer is automatically reset if the trip exceeds 9999 hours or 99,999 miles. You can select km or miles as the unit of measurement for distance (Y page 229).
Displaying the range and current fuel consumption X Press = or ; on the steering wheel to select the Trip menu. X Press the 9 or : button to select
current fuel consumption and approximate range.
: Current fuel consumption21
; Approximate range Approximate range ; is calculated according to current driving style and the amount of fuel in the tank. If there is only a small amount of fuel left in the fuel tank, the display shows a vehicle being refueled C instead of range ;.Digital speedometer X Press = or ; on the steering wheel to select the Trip menu. X Press 9 or : to select the digital
speedometer.
Trip menu Standard display
X Press and hold the % button on the steering wheel until the Trip menu with odometer : and trip odometer ; is shown.
Trip computer "From start" or "From reset" The values in the From Start submenu are calculated from the start of a journey whilst the values in the From Reset submenu are calculated from the last time the submenu was reset. X Press = or ; on the steering wheel to select the Trip menu. X Press 9 or : to select From Start or From Reset.
Trip computer "After start" (example) : Distance ; Time = Average speed ? Average fuel consumption The From Start trip computer is reset automatically when
21 Not in AMG vehicles.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 221
Version: 3.0.3.6Menus and submenus
221
Resetting values You can reset the values of the following functions: RTrip odometer RTrip computer "From start" RTrip computer "From reset" X Press = or ; on the steering wheel to select the Trip menu. X Press 9 or : to select the function
that you wish to reset.
X Press a.
Resetting the trip computer "From start" (example) X Press the : button to select Yes and press the a button to confirm.
AMG menu in AMG vehicles AMG displays X Press = or ; on the steering wheel to select the AMG menu.
: Digital speedometer ; Gear indicator = Upshift instruction ? Engine oil temperature A Coolant temperature Shift UP instruction = indicates that the engine has reached the overrevving range when in the manual gearshift program. Shift up instruction = overrides other messages in the multifunction display until you have shifted up. When the engine temperature is below 80 †, the oil temperature gauge flashes. Avoid driving at full engine output during this time.
SETUP SETUP shows the drive program, the ESP® (Electronic Stability Program) mode and the SPORT handling mode. X Press = or ; on the steering wheel to select the AMG menu. X Press the 9 button repeatedly until
SETUP is displayed.
or X Briefly press the AMG button on the center
console.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 222
Version: 3.0.3.6222 Menus and submenus
: Drive program (C/S/S+/M) ; ESP® mode (ON/OFF) or SPORT handling 3 Suspension tuning (COMFORT/SPORT/
mode (SPORT) SPORT+) RACETIMER Displaying and starting RACETIMER G Warning The RACETIMER feature is only for use on roads and in conditions where high speed driving is permitted. Racing on public roads is prohibited under all circumstances. The driver is and must always remain responsible for following posted speed limits.
You can use the RACETIMER to store lap times. When RACETIMER is displayed, you cannot adjust the volume using the W and X buttons on the steering wheel. X Press = or ; on the steering wheel to select the AMG menu. X Press the 9 button repeatedly until the
RACETIMER is shown.
: RACETIMER ; Lap You can start the RACETIMER when the engine is running or if the SmartKey is in position 2 in the ignition lock. X To start: press the W button to start the
RACETIMER.
X To display the intermediate time: press
X to show the intermediate time. The intermediate time is displayed for five seconds.
X To stop: press the W button to stop the
RACETIMER.
The RACETIMER interrupts timing when you stop the vehicle and turn the SmartKey to position 1 in the ignition lock. When you turn the SmartKey to position 2 or 3 and then press the W button, timing is continued. Storing the lap time and starting a new lap It is possible to store a maximum of sixteen laps. X Press the X button on the steering
wheel to show the intermediate time during timing. The intermediate time is displayed for five seconds.
X Press the X button again within five
seconds. The displayed intermediate time is stored as a lap time. Timing starts for a new lap. The new lap is timed from when the intermediate time is called up.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 223
Version: 3.0.3.6Menus and submenus
223
: RACETIMER ; Fastest lap time (best lap) = Lap Resetting the current lap X Press the W button on the steering
wheel to stop the RACETIMER.
X Press X to reset the lap time to "0”.
Deleting all laps You cannot delete individual stored laps. X Press the W button on the steering
wheel to stop the RACETIMER. X Press a. Reset Race Timer? appears in the multifunction display.
X Press the : button to select YES and press the a button to confirm. All laps are deleted.
Overall evaluation This function is shown if you have stored at least one lap and stopped the RACETIMER. X Press = or ; on the steering wheel to select the AMG menu. X Press the 9 button repeatedly until the
overall evaluation is shown.
: RACETIMER overall evaluation ; Total time driven = Average speed ? Distance covered A Top speed
Lap evaluation This function is only available if you have stored at least two laps and have stopped the RACETIMER. X Press = or ; on the steering wheel to select the AMG menu. X Press the 9 button repeatedly until the
lap evaluation is shown. Each lap is shown in a separate submenu. The fastest lap is indicated by flashing symbol :.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 224
Version: 3.0.3.6224 Menus and submenus
Route guidance active No change of direction announced
: Distance to destination ; Distance to next change of direction = Current road ? Symbol for "follow the road's course" Change of direction announced without a lane recommendation
: Road into which the change of direction
leads
; Distance to change of direction and visual
distance display
= Symbol for change of direction When a change of direction has been announced, you will see visual distance display ; next to symbol = for the change of direction. This decreases in size as you approach the announced change of direction. Change of direction announced with a lane recommendation Lane recommendations are only displayed if the relevant data is available on the digital map.
: Lap ; Lap time = Average lap speed ? Lap length A Top speed during lap X Press 9 or : to select a different lap
evaluation.
Navigation menu Displaying navigation instructions In the Navi menu, the multifunction display shows navigation instructions. For more information, see the separate operating instructions. X Switch on COMAND (see the separate
operating instructions). X Press the = or ; button on the steering wheel to select the Navi menu.
Route guidance inactive
: Direction of travel ; Current road
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 225
Version: 3.0.3.6Menus and submenus
225
Audio menu Selecting a radio station i SIRIUS XM satellite radio acts like a
normal radio. For more information on satellite radio operation, see the separate operating instructions.
You can only change the waveband and store new stations using COMAND. X Switch on COMAND and select Radio (see
the separate operating instructions). X Press the = or ; button on the steering wheel to select the Audio menu.
: Road into which the change of direction
leads
; Distance to change of direction and visual
distance display
= Lane recommendation ? Symbol for change of direction On multi-lane roads, lane recommendation = may be shown for the next change of direction. Lanes may be added during a change of direction.
Lane recommendation display (example) : Uninterrupted lane ; New lane during a change of direction = Lane recommended for the change of
direction
Other status indicators of the navigation system RO: you have reached the destination. RNew Route... or Calculating Route: a new route is being calculated. ROff Map or Off Mapped Road: the vehicle position is outside the area of the digital map (off-map position). RNo Route: no route could be calculated to the selected destination.
: Waveband22
; Station X To select a stored channel: briefly pressthe 9 or : button.
X To select a channel from the channel
list: press and briefly hold the 9
or : button.X To select a station using the station
search23: press and briefly hold the 9
or : button.Audio player or audio media operation Audio data from various audio devices or media can be played, depending on the equipment installed in the vehicle.
22 When station ; has been stored, the memory position will also be displayed. 23 Only if no station list is received.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 226
Version: 3.0.3.6226 Menus and submenus
X Switch on COMAND and select the audio
player or medium (see the separate operating instructions). X Press the = or ; button on the steering wheel to select the Audio menu.
X To select the next or previous scene:
briefly press the 9 or the : button.
X To select a scene from the scene list
(rapid scrolling): press and hold the 9 or : button until the desired scene has been reached.
Telephone menu Introduction You can establish a Bluetooth® wireless connection to COMAND APS (see the separate operating instructions). G Warning A driver's attention to the road must always be his/her primary focus when driving. For your safety and the safety of others, we recommend that you pull over to a safe location and stop before placing or taking a telephone call. If you choose to use the telephone while driving, please use the hands- free device and only use the telephone when weather, road and traffic conditions permit. Some jurisdictions prohibit the driver from using a mobile phone while driving a vehicle. Bear in mind that at a speed of just 30 mph (approximately 50 km/h ), your vehicle is covering a distance of 44 feet (approximately 14 m) every second.
X Switch on the mobile phone and COMAND
APS (see the separate operating instructions). X Press the = or ; button on the steering wheel to select the Tel menu. You will see one of the following display messages in the multifunction display: RTelephone Ready or the name of the network provider: the mobile phone has found a network and is ready to receive. RNo Service: No network is available.
CD player display (example) : Current track X To select the next/previous track: briefly press the 9 or : button. X To select a track from the track list
(rapid scrolling): press and hold the 9 or : button until the desired track has been reached.
If you press and hold 9 or :, the rapid scrolling speed is increased. Not all audio players or media support this function. If track information is stored on the audio player or medium, the multifunction display will show the number and name of the track. The current track does not appear in audio AUX mode (Auxiliary audio mode: external audio source connected).
Video DVD operation X Switch on COMAND APS and select video
DVD (see the separate operating instructions). X Press the = or ; button on the steering wheel to select the Audio menu.
: Current scene
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 227
Version: 3.0.3.6Menus and submenus
227
Accepting a call If someone calls you when you are in the Tel menu, a display message appears in the multifunction display, for example:
X Press 6 on the steering wheel to accept
an incoming call. You can accept a call even if you are not in the Tel menu. Rejecting or ending a call X Press the ~ button on the steering
wheel. You can end or reject a call even if you are not in the Tel menu. Dialing a number from the phone book If your mobile phone is able to receive calls, you can search for and dial a number from the phone book in COMAND at any time. X Copy the telephone book of the mobile
phone to COMAND (see the separate operating instructions). X Press the = or ; button on the steering wheel to select the Tel menu. X Press the 9, : or a button to call
up the phone book.
X Press 9 or : to select the name you
are searching for. To start scrolling rapidly, press and hold the 9 or : button for longer than one second. After a short time, the rapid scroll speeds up. Rapid scrolling stops when you release the button or reach the end of the list.
X If only one telephone number is stored for a name: press the 6 or a button to start dialing.
or X If there is more than one number for a particular name: press the 6 or a button to display the numbers.
X Press the 9 or : button to select the
number you want to dial.
X Press the 6 or a button to start
dialing.
or X If you do not want to make a call: press
the ~ button.
Redialing The on-board computer saves the last names or numbers dialed in the redial memory. X Press the = or ; button on the steering wheel to select the Tel menu. X Press the 6 button to switch to the
redial memory.
X Press the 9 or : button to select the
desired name or number.
X Press the 6 or a button to start
dialing.
Assistance menu Showing the distance display This function is only available with DISTRONIC PLUS. X Press the = or ; button on the steering wheel to select the DriveAssist menu. X Press the 9 or : button to select Distance Display. X Press a.
The DISTRONIC PLUS distance display (Y page 185) appears in the multifunction display.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 228
Version: 3.0.3.6228 Menus and submenus
Deactivating/activating ESP® G Warning! Never switch off the ESP when you see the ESP warning lamp ä flashing in the instrument cluster. In this case proceed as follows: RWhen driving off, apply as little throttle as
possible.
RWhile driving, ease up on the accelerator
pedal.
RAdapt your speed and driving style to the
prevailing road conditions.
Failure to observe these guidelines could cause the vehicle to skid. The ESP cannot prevent accidents resulting from excessive speed.
Further information about ESP®(Y page 67). This function is not available in AMG vehicles. X Start the engine. X Press the = or ; button on the steering wheel to select the DriveAssist menu. X Press 9 or : to select ESP. X Press a. X To deactivate: press a again.
The å warning lamp in the instrument cluster comes on. G Warning When the å ESP OFF warning lamp lights up, ESP is switched off. When the ä ESP warning lamp and the å ESP OFF warning lamp are on continuously, ESP is not operational due to a malfunction. When ESP is switched off or not operational, the vehicle's stability during standard driving maneuvers is reduced. Adapt your driving style to suit the prevailing road conditions/weather conditions and to the non-operating status of ESP.
X To activate: press a again.
The å warning lamp in the instrument cluster goes out.
Activating/deactivating PRE-SAFE® Brake This function is only available with DISTRONIC PLUS. X Press the = or ; button on the steering wheel to select the DriveAssist menu. X Press 9 or : to select PRE-SAFE Brake. X Press a.
The current selection is displayed.
X To activate/deactivate: press a
again.
When PRE-SAFE® Brake (Y page 71) is activated, the multifunction display shows the Ä symbol.
Activating/deactivating ATTENTION ASSIST X Press the = or ; button on the steering wheel to select the DriveAssist menu. X Press the 9 or : button to select Attention Asst. X Press a.
The current selection is displayed.
X To activate/deactivate: press a
again.
When ATTENTION ASSIST (Y page 201) is activated, the À symbol appears in the multifunction display when the ignition is on.
Activating/deactivating Blind Spot Assist You can use the Blind Spot Asst. function to activate or deactivate Blind Spot Assist (Y page 205) or Active Blind Spot Assist (Y page 209).
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 229
Version: 3.0.3.6Menus and submenus
229
X Press the = or ; button on the steering wheel to select the DriveAssist menu. X Press the 9 or : button to select Blind Spot Asst.. X Press a.
The current selection is displayed.
X To activate/deactivate: press a
again.
Activating/deactivating Lane Keeping Assist You can use the Lane Keep. Asst. function to activate/deactivate Lane Keeping Assist (Y page 207) or Active Lane Keeping Assist (Y page 211). X Press the = or ; button on the steering wheel to select the DriveAssist menu. X Press the 9 or : button to select Lane Keep. Asst.. X Press a.
The current selection is displayed.
X To activate/deactivate: press a
again.
When Lane Keeping Assist is activated, the à symbol appears in the multifunction display when the ignition is on.
Maintenance menu
In the Serv. menu, you can: Rcall up display messages (Y page 234) Rrestart the tire pressure loss warning
system (Canada only) (Y page 355)
Rcheck the tire pressure electronically
(Y page 357)
Rcall up the service due date (Y page 313)
Settings menu Introduction
In the Settings menu, you have the following options: RChanging the instrument cluster settings RChanging the lighting settings RChanging the vehicle settings RChanging the convenience settings RRestoring the factory settings
Instrument cluster Selecting the unit of measurement for distance The Display Unit Speed-/Odometer: function allows you to choose whether certain displays appear in km/h or mph. The selected unit of measurement for distance applies to: Rthe digital speedometer in the Trip menu Rthe odometer and the trip odometer Rthe trip computer Rthe navigation instructions in the Navi menu
RDISTRONIC PLUS X Press the = or ; button on the steering wheel to select the Settings menu. X Press the : or 9 button to select the Instr. Cluster submenu. X Press the a button to confirm.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 230
Version: 3.0.3.6230 Menus and submenus
X Press the : or 9 button to select the Display Unit Speed-/Odometer. function. You will see the selected setting: km or miles. X Press the a button to save the setting.
Selecting the permanent display function The Permanent Display: function allows you to choose whether the multifunction display always shows the outside temperature or the speed in km/h (USA) or mph (Canada). X Press the = or ; button on the steering wheel to select the Settings menu. X Press the : or 9 button to select the Instr. Cluster submenu. X Press the a button to confirm. X Press : or 9 to select the Permanent Display: function. You will see the selected setting Outside Temperature or Speedometer [km/h]:. X Press the a button to save the setting.
Lights Switching the daytime running lamps on/ off This function is not available in Canada. If you have activated the Daytime Running Lights: function and the light switch is in the c position the daytime running lamps are switched on automatically when the engine is running. In the dark, the following also light up: Rthe low-beam headlamps Rthe parking lamps Rthe tail lamps Rthe license plate lamp Rthe side marker lamps
X Press the = or ; button on the steering wheel to select the Settings menu. X Press the : or 9 button to select the Lights submenu. X Press the a button to confirm. X Press the : or 9 button to select the Daytime Running Lights: function. You will see the selected setting: Enabled or Disabled. X Press the a button to save the setting.
Switching Adaptive Highbeam Assist on/ off X Press the = or ; button on the steering wheel to select the Settings menu. X Press the : or 9 button to select the Lights submenu. X Press the a button to confirm. X Press the : or 9 button to select the Adaptive Highbeam Assist: function. You will see the selected setting: Enabled or Disabled. X Press the a button to save the setting.
Setting the brightness of the ambient lighting X Press the = or ; button on the steering wheel to select the Settings menu. X Press the : or 9 button to select the Lights submenu. X Press the a button to confirm. X Press the : or 9 button to select the Ambient Light Brightness: function. You will see the selected setting. X Press the a button to confirm. X Press the : or 9 button to adjust the brightness to any level from Disabled to Level 5 (bright). X Press the a or % button to save the
setting.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 231
Version: 3.0.3.6Menus and submenus
231
Activating/deactivating surround lighting and exterior lighting delayed switch-off If you switch on the Locator Lighting: function and the light switch is set to c, Rthe exterior lighting switches on when it is
dark after unlocking the vehicle with the SmartKey. The exterior lighting switches off when you open the driver’s door.
Rthe exterior lighting remains on for 15
seconds when it is dark after closing the doors. If the engine is switched off and then none of the doors are opened, or if an open door is not closed, the exterior lighting goes out after 60 seconds. If you activate the Locator Lighting: function, the following light up: Rthe parking lamps Rthe tail lamps Rthe fog lamps24
Rthe low-beam headlamps25
Rthe license plate lamp Rthe side marker lamps X Press the = or ; button on the steering wheel to select the Settings menu. X Press the : or 9 button to select the Lights submenu. X Press the a button to confirm. X Press the : or 9 button to select the Locator Lighting: function. You will see the selected setting: Enabled or Disabled. X Press the a button to save the setting.To deactivate the delayed shut-off temporarily: X Before leaving the vehicle, turn the
SmartKey to position 0 in the ignition lock.
X Turn the SmartKey to position 2 in the
ignition lock and back to position 0. The delayed shut-off is deactivated.
The delayed shut-off is reactivated the next time you start the engine. Activating/deactivating the interior lighting delayed switch-off When you activate the Interior Lighting Delay: function and remove the SmartKey from the ignition lock, the interior lighting remains on for 10 seconds. X Press the = or ; button on the steering wheel to select the Settings menu. X Press the : or 9 button to select the Lights submenu. X Press the a button to confirm. X Press the : or 9 button to select the Interior Lighting Delay: function. You will see the selected setting: Enabled or Disabled. X Press the a button to save the setting.
Vehicle Activating/deactivating the automatic locking feature If you select the Automatic Door Lock: function, the vehicle is centrally locked above a speed of around 9 mph (15 km/h). i Further information on the automatic
locking feature (Y page 85).
24 Only for vehicles with front fog lamps. 25 Only for vehicles without front fog lamps.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 232
Version: 3.0.3.6232 Menus and submenus
X Press the = or ; button on the steering wheel to select the Settings menu. X Press the : or 9 button to select the Vehicle submenu. X Press the a button to confirm. X Press the : or 9 button to select the Automatic Door Lock: function. You will see the selected setting: Enabled or Disabled. X Press the a button to save the setting.
Activating/deactivating the acoustic locking confirmation If you switch on the Acoustic Lock Feedback: function, an acoustic signal sounds when you lock or unlock the vehicle. When unlocking, the signal sounds once. When locking, it sounds three times. X Press the = or ; button on the steering wheel to select the Settings menu. X Press the : or 9 button to select the Vehicle submenu. X Press the a button to confirm. X Press the : or 9 button to select the Acoustic Lock Feedback: function. You will see the selected setting: Enabled or Disabled. X Press the a button to save the setting.
Activating/deactivating the radar sensor system The following systems are switched off when the radar sensor system is deactivated: RDISTRONIC PLUS (Y page 179) RBAS PLUS (Y page 66) RPRE-SAFE® Brake (Y page 71) RBlind Spot Assist (Y page 205) RActive Blind Spot Assist (Y page 209) i USA only: This device has been approved by the FCC as a “Vehicular Radar System”. The radar sensor is intended for use in an
automotive radar system only. Removal, tampering, or altering of the device will void any warranties, and is not permitted by the FCC. Do not tamper with, alter, or use in any non-approved way. Any unauthorized modification to this device could void the user’s authority to operate the equipment.
i Canada only:
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Any unauthorized modification to this device could void the user’s authority to operate the equipment. X Press the = or ; button on the steering wheel to select the Settings menu. X Press the : or 9 button to select the Vehicle submenu. X Press the a button to confirm. X Press the 9 or : button to select Radar Sensor (See Oper. Manual). You will see the selected setting: Enabled or Disabled. X Press the a button to save the setting.
Convenience Activating/deactivating the EASY- ENTRY/EXIT feature You can use the Easy Entry/Exit: function to activate or deactivate the easy-entry/exit feature (Y page 112). G Warning! You must make sure no one can become trapped or injured by the moving steering
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 233
Version: 3.0.3.6Menus and submenus
233
wheel when the easy-entry/exit feature is activated. To stop steering wheel movement, move steering wheel adjustment lever or press one of the memory position buttons. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Children could open the driver's door and unintentionally activate the easy-entry/exit feature, which could result in an accident and/or serious personal injury.
X Press the = or ; button on the steering wheel to select the Settings menu. X Press the : or 9 button to select the Convenience submenu. X Press the a button to confirm. X Press the : or 9 button to select the Easy Entry/Exit: feature. You will see the selected setting: Enabled or Disabled. X Press the a button to save the setting.
Switching the belt adjustment on/off Further information on belt adjustment (Y page 56). X Press the = or ; button on the steering wheel to select the Settings menu. X Press the : or 9 button to select the Convenience submenu. X Press the a button to confirm. X Press the : or 9 button to select the Belt Adjustment: function. You will see the selected setting: Enabled or Disabled. X Press the a button to save the setting.
Resetting to factory settings For safety reasons, the Daytime Running Lights: function in the Lights submenu is only reset if the vehicle is stationary.
X Press the = or ; button on the steering wheel to select the Settings menu. X Press the : or 9 button to select the Factory Setting submenu. X Press the a button to confirm. The Reset All Settings? message appears. X Press the : or 9 button to select No or Yes. X Press the a button to confirm the selection. If you have selected Yes, the multifunction display shows a confirmation message.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 234
Version: 3.0.3.6234 Display messages
Display messages Hiding display messages G Warning All categories of messages contain important information which should be taken note of and, where a malfunction is indicated, addressed as soon as possible at an authorized Mercedes-Benz Center. Failure to repair the condition noted may cause damage not covered by the Mercedes-Benz Limited Warranty, or result in property damage or personal injury.
Display messages appear in the multifunction display. X Press the a or % button on the steering wheel to hide the display message.
The display message is cleared.
The multifunction display shows high-priority display messages in red. You cannot hide display messages of the highest priority. The multifunction display shows these messages continuously until the causes for the messages have been remedied. Certain display messages are accompanied by an audible warning tone or a continuous tone. Please respond in accordance with the display messages and follow the additional notes in this Operator's Manual. When you stop and park the vehicle, please observe the notes on HOLD (Y page 188) and parking (Y page 169).
Message memory The on-board computer saves certain display messages. You can call up the display messages in the message memory. X Press the = or ; button on the steering wheel to select the Service menu. If there are display messages, the multifunction display shows, for example, 2 messages. X Press the 9 or : button to select the entry, e.g. 2 messages. X Confirm with a. X Press the 9 or : button to scroll through the display messages. When the ignition is switched off, all display messages are deleted apart from some high- priority display messages. Once the causes of the high-priority display messages have been rectified, the corresponding display messages are also deleted.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 235
Version: 3.0.3.6Display messages
235
Safety systems Display messages ÷ Inoperative See Operator's Manual
Tele Aid Inoperative
PRE-SAFE Inoperative See Operator's Manual
Possible causes/consequences and M Solutions G Risk of accident ESP® (Electronic Stability Program), BAS (Brake Assist), PRE-SAFE®, the HOLD function and hill start assist are not available due to a malfunction. BAS PLUS (Brake Assist PLUS) and PRE-SAFE® Brake may be inoperative as well. In addition, the ä and å warning lamps light up in the instrument cluster. ATTENTION ASSIST is deactivated. The brake system continues to function normally, but without the functions listed above. X Drive on carefully. X Visit a qualified specialist workshop. USA only: one or more main functions in the mbrace system are malfunctioning. Canada only: one or more of the main functions of the TELEAID system is malfunctioning. X USA only: have the mbrace system checked at a qualified
specialist workshop.
X Canada only: have the TELEAID system checked at a qualified
specialist workshop. G Risk of injury Important functions of PRE-SAFE® have failed. All other occupant safety systems, e.g. air bags, remain available. X Visit a qualified specialist workshop immediately.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 236
Version: 3.0.3.6236 Display messages
Display messages PRE-SAFE Function Currently Limited See Oper. Manual
PRE-SAFE Functions Limited See Operator's Manual Check Child Seat Pos. See Operator's Manual
Possible causes/consequences and M Solutions G Risk of accident PRE-SAFE® Brake is temporarily inoperative if: Rthe DISTRONIC PLUS cover in the radiator grill is dirty. Rthe sensors in the bumpers are dirty. Rits function is impaired due to heavy rain or snow. Rthe radar sensor system is temporarily inoperative, e.g. due to
electromagnetic radiation emitted by nearby TV or radio stations or other sources of electromagnetic radiation. Rthe system is outside the operating temperature range. Rthe on-board voltage is insufficient. RE 63 AMG: you deactivate ESP®. PRE-SAFE® Brake is operational again and the display message disappears when: Rthe dirt (e.g. slush) drops away while the vehicle is in motion. Rthe system detects that the sensors are fully available again. Rthe system is within the operating temperature range. RE 63 AMG: you reactivate ESP®. If the display message continues to be displayed: X Clean the DISTRONIC PLUS cover in the radiator grill
(Y page 317).
X Clean the bumpers (Y page 317). X Restart the engine. X Wait until the battery is sufficiently charged. G Risk of accident PRE-SAFE® Brake is faulty. BAS PLUS or the distance warning signal may also have failed. X Visit a qualified specialist workshop. G Risk of injury Vehicles with BabySmart™ (Canada only): The BabySmart™ child seat is positioned incorrectly. X Install the child seat in the correct position. G Risk of injury Vehicles with BabySmart™ (Canada only): The sensor for automatic child seat recognition is faulty. X Visit a qualified specialist workshop.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 237
Version: 3.0.3.6Display messages
237
Display messages SRS Malfunction Service Required
Front Left SRS Malfunction Service Required orFront Right SRS Malfunction Service Required Rear Left SRS Malfunction Service Required orRear Right SRS Malfunction Service Required Rear Center SRS Malfunction Service Required Left Side Curtain Airbag Malfunction Service Required orRight Side Curtain Airbag Malfunction Service Required
Possible causes/consequences and M Solutions G Risk of injury There is a malfunction in the SRS (Supplemental Restraint System). The 6 warning lamp also lights up in the instrument cluster. X Visit a qualified specialist workshop. G Risk of injury SRS has malfunctioned at the front on the left or right. The 6
warning lamp also lights up in the instrument cluster. X Visit a qualified specialist workshop.G Risk of injury SRS has malfunctioned at the rear on the left or right. The 6
warning lamp also lights up in the instrument cluster. X Visit a qualified specialist workshop.G Risk of injury SRS has malfunctioned at the rear center. The 6 warning lamp also lights up in the instrument cluster. X Visit a qualified specialist workshop. G Risk of injury There is a malfunction in the left-hand and/or right-hand window curtain air bag. The 6 warning lamp also lights up in the instrument cluster. X Visit a qualified specialist workshop.
G Warning In the event a malfunction of the SRS is indicated as outlined above, the SRS may not be operational.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 238
Version: 3.0.3.6238 Display messages
For your safety, we strongly recommend that you contact an authorized Mercedes-Benz Center immediately to have the system checked. Otherwise the SRS may not be activated when needed in an accident, which could result in serious or fatal injury, or it might deploy unexpectedly and unnecessarily which could also result in injury.
BA 212 USA, CA Edition B 2011; 1; 5, en-US dimargi
2010-05-20T13:33:46+02:00 - Seite 239
Version: 3.0.3.6Display messages
239
