Download PDF Manual


왘 If you are starting the engine with KEYLESS-GO: Close any doors that may be open to allow for better detec- tion of the SmartKey with KEYLESS-GO. or: Start the engine with the SmartKey as radio signals from another source may be interfering with the SmartKey with KEYLESS-GO.


왘 Repeat the starting procedure


(컄 page 45). Remember that extended starting attempts can drain the battery.


왘 Get a jump start (컄 page 351). If the engine does not start after several starting attempts, there could be a mal- function in the engine electronics or in the fuel supply system. 왘 Notify an authorized Mercedes-Benz


Center.


Parking brake


1 Parking brake pedal 2 Parking brake release handle


Getting started Driving


Warning!


When leaving the vehicle, always remove the SmartKey from the starter switch, take the SmartKey with KEYLESS-GO* with you and lock your vehicle. Do not leave children un- attended in the vehicle, or with access to an unlocked vehicle. Children could release the parking brake, which could result in an acci- dent and/or serious injury.


왘 Release the parking brake by pulling on


handle 2. The warning lamp ; (USA only) or 3 (Canada only) in the instrument cluster goes out.


Driving 왘 Depress the brake pedal. 왘 Move gear selector lever in position D


or R.


Warning!


It is dangerous to shift the gear selector le- ver out of P or N if the engine speed is high- er than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accel- erate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal. 컄컄


47


Getting started Driving


컄컄


Warning!


On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehi- cle control. Your vehicle’s ABS will not pre- vent this type of loss of control.


In order to avoid damaging the trans- mission, 앫 wait for the gear selection process to complete before setting the vehi- cle in motion.


앫 place the gear selector lever in


position R only when the vehicle is stopped.


왘 Release the brake pedal. 왘 Carefully depress the accelerator.


Once the vehicle is in motion, the automatic central locking system engages and the locking knobs drop down.


If you hear a warning signal and a mes- sage in the multifunction display ap- pears when driving off, you have forgotten to release the parking brake. Release the parking brake.


After a cold start, the automatic transmis- sion shifts at a higher engine revolution. This allows the catalytic converter to reach its operating temperature faster.


Do not run cold engine at high engine speeds. Running a cold engine at high engine speeds may shorten the service life of the engine.


Simultaneously depressing the acceler- ator pedal and applying the brake re- duces engine performance and causes premature brake and drivetrain wear.


You can open a locked door from the inside. Open doors only when condi- tions are safe to do so. You can deactivate the automatic lock- ing using the control system (컄 page 153).


For more information, see “Driving instruc- tions” (컄 page 247).


48


Switching on headlamps


Turn signals and high beam


The combination switch is located on the left of the steering column.


Exterior lamp switch 1 Off 2 Low beam headlamps on 왘 Turn the switch to B. For more information, see “Exterior lamp switch” (컄 page 119).


Combination switch 1 Turn signals, right 2 Turn signals, left 왘 Press the combination switch up 1 or


down 2.


To signal minor directional changes, move combination switch to point of resistance only and release. The turn signal flashes three times.


Getting started Driving


High beam 왘 Push the combination switch forward. The high beam headlamps are switched on. The high beam headlamp indicator A in the instrument clus- ter comes on.


For more information, see “High beam flasher” (컄 page 123).


49


Switching on windshield wipers 왘 Turn the combination switch to the de- sired position depending on the inten- sity of the rain. 0 Windshield wipers off


Intermittent wiping (interval depen- dent on wetness of windshield)


II Normal wiper speed III Fast wiper speed


The intermittent wiping interval is de- pendent on wetness of the windshield. Wiping will not occur with a door open.


Do not leave windshield wipers in inter- mittent setting when vehicle is taken to an automatic car wash or during wind- shield cleaning. Wipers will operate in the presence of water sprayed on the windshield, and wipers may be dam- aged as a result. The switch should not be left in inter- mittent setting as the wipers will wipe the windshield once every time the en- gine is started. Dust that accumulates on the windshield might scratch the glass and/or damage the wiper blades when wiping occurs on a dry wind- shield.


Getting started Driving


Windshield wipers


The combination switch is located on the left of the steering column.


Combination switch 1 Single wipe 2 Switching on windshield wipers 왘 Make sure the ignition is switched on. All the lamps in the instrument cluster come on.


50


Single wipe 왘 Press switch briefly in the direction of


arrow 1. The windshield wipers wipe one time without washer fluid.


Wiping with windshield washer fluid 왘 Press switch in the direction of


arrow 1 past the resistance point. The windshield wiper operates with washer fluid.


For information on filling up the washer reservoir, see “Windshield washer system and headlamp cleaning system” (컄 page 269)


If anything blocks the windshield wip- ers (leaves, snow, etc.), switch them off immediately. 앫 For safety reasons,


앫 turn off the engine by turning


the SmartKey to position 0 and withdraw SmartKey from starter switch


or 앫 turn off the engine by pressing the KEYLESS-GO* start/stop button and open the driver’s door (with the driver’s door open, starter switch is in position 0, same as with SmartKey removed from starter switch)


before attempting to remove any blockage.


Getting started Driving


앫 Remove blockage. 앫 Turn the windshield wipers on


again.


If windshield wipers fail to function at all in switch position I, 앫 set the combination switch to the


next highest wiper speed


앫 have the windshield wipers


checked at the nearest authorized Mercedes-Benz Center


51


Getting started Driving


Problems while driving


The engine runs erratically and misfires 앫 An ignition cable may be damaged. 앫 The engine electronics may not be op-


erating properly.


앫 Unburned gasoline may have entered the catalytic converter and damaged it.


왘 Give very little gas. 왘 Have the problem repaired by an au- thorized Mercedes-Benz Center as soon as possible.


52


The coolant temperature is above 248°F (120°C) The coolant is too hot and is no longer cooling the engine. 왘 Stop the vehicle as soon as possible and turn off the engine. Allow engine and coolant to cool.


왘 Check the coolant level and add cool-


ant if necessary (컄 page 266).


Excessive coolant temperatures trigger a warning message in the multifunction display (컄 page 306).


In case of accident If the vehicle is leaking gasoline: 왘 Do not start the engine under any cir-


cumstances.


왘 Notify local fire and/or police authori-


ties.


If the extent of the damage cannot be de- termined: 왘 Notify an authorized Mercedes-Benz


Center.


If no damage can be determined on the 앫 major assemblies 앫 fuel system 앫 engine mount: 왘 Start the engine in the usual manner.


왔 Parking and locking You have now completed your first drive. You have properly stopped and parked your vehicle. End your drive as follows:


Warning!


Wait until the vehicle is stationary before re- moving the SmartKey from the starter switch. The vehicle cannot be steered when the SmartKey is removed.


Warning!


With the engine not running, there is no power assistance for the brake and the steering systems. In this case, it is impor- tant to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle.


Warning!


Do not park this vehicle in areas where com- bustible materials such as grass, hay or leaves can come into contact with the hot exhaust system, as these materials could be ignited and cause a vehicle fire.


To reduce the risk of personal injury as a re- sult of vehicle movement, before turning off the engine and leaving the vehicle always: 앫 Keep right foot on brake pedal. 앫 Firmly depress parking brake pedal. 앫 Move the gear selector lever to


position P.


앫 Slowly release brake pedal. 앫 When parked on an incline, turn front


wheels towards the road curb.


Getting started Parking and locking


앫 Turn the SmartKey to starter switch


position 0 and remove, or press start/stop button (vehicles with KEYLESS-GO*).


앫 Take the SmartKey or the SmartKey with


KEYLESS-GO* and lock vehicle when leaving.


53


Warning!


Warning!


When leaving the vehicle, always remove the SmartKey from the starter switch, take the SmartKey with KEYLESS-GO* with you and lock your vehicle. Do not leave children un- attended in the vehicle, or with access to an unlocked vehicle. Children could release the parking brake and/or move the gear selec- tor lever from position P, either of which could result in an accident and/or serious personal injury.


Getting out of your vehicle with the gear se- lector lever not fully engaged in position P is dangerous. Also, when parked on an incline, position P alone may not prevent your vehi- cle from moving, possibly hitting people or objects.


Always set the parking brake in addition to shifting to position P (컄 page 45). When parked on an incline, turn front wheels towards the road curb.


Getting started Parking and locking


Parking brake


1 Parking brake 2 Release handle 왘 Step firmly on parking brake 1.


When the engine is running, the indica- tor lamp ; (USA only) or 3 (Canada only) in the instrument cluster will be illuminated.


54


Switching off headlamps


왘 Turn the exterior lamp switch to M


(컄 page 49).


For more information, see “Exterior lamp switch” (컄 page 119).


Turning off with the SmartKey 왘 Turn the SmartKey in the starter switch (컄 page 31) to position 0 and remove it. The immobilizer is activated.


Turning off the engine


왘 Place the gear selector lever in


position P.


The SmartKey can only be removed from the starter switch with the gear selector lever in position P.


Always set the parking brake in addi- tion to shifting to position P. On steep slopes, turn the front wheels towards the curb.


왘 Press the seat belt release button


(컄 page 44). Allow the retractor to completely re- wind the seat belt by guiding the latch plate.


With the SmartKey removed and the driver’s door open, a warning sounds if the vehicle’s exterior lamps are not switched off.


Getting started Parking and locking


Warning!


To prevent possible personal injury, always keep hands and fingers away from the door openings when closing the doors. Be espe- cially careful when small children are around.


Before closing doors, make sure there is no possibility of someone getting caught in a door during closing.


왘 After exiting the vehicle press the lock


button ‹ on the SmartKey (컄 page 30). All turn signal lamps flash three times. The locking knobs on the doors move down.


55


Getting started Parking and locking


Warning!


When leaving the vehicle, always remove the SmartKey from the starter switch and lock your vehicle. Do not leave children unat- tended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehi- cle equipment may cause an accident and/or serious personal injury.


For more information, see “Locking and unlocking” (컄 page 88).


56


Turning off the engine with KEYLESS-GO* 왘 Place the gear selector lever in


position P.


왘 Press the KEYLESS-GO start/stop but-


ton to shut off the engine. With the driver's door closed, the start- er switch is now in position 1. With the driver’s door opened, the starter switch is set to position 0, same as SmartKey removed from starter switch (컄 page 31).


왘 Press the seat belt release button


(컄 page 44). Allow the retractor to completely re- wind the seat belt by guiding the latch plate.


If you hear a warning signal, you have either 앫 forgotten to turn off the lights be-


fore opening the driver’s door or


앫 tried to turn off the engine while the


gear selector lever is not in P .


Turn off the lights or place the gear se- lector lever in P.


Opening a door causes the windows on that side of the car to open slightly. They will return to the up position when the door is closed.


Warning!


To prevent possible personal injury, always keep hands and fingers away from the door openings when closing the doors. Be espe- cially careful when small children are around.


Before closing doors, make sure there is no possibility of someone getting caught in a door during closing.


1 Lock button on the door handle 왘 After exiting the vehicle, press lock


button 1 on the door handle or on the trunk lid. All turn signal lamps flash three times. The locking knobs on the doors move down.


Getting started Parking and locking


Warning!


When leaving the vehicle, always remove the SmartKey from the starter switch, take the SmartKey with KEYLESS-GO* with you, and lock your vehicle. Do not leave children un- attended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehi- cle equipment may cause an accident and/or serious personal injury.


For more information, see “Locking and unlocking” (컄 page 88).


57


58


Safety and Security Occupant safety


Panic alarm


Driving safety systems


Anti-theft systems


59


Safety and Security Occupant safety 왔 Occupant safety In this section you will learn the most im- portant facts about the restraint systems of the vehicle. The restraint systems are: 앫 Seat belts 앫 Emergency tensioning device 앫 Airbags 앫 Child seats 앫 Child seat recognition 앫 Lower anchors and tethers for children


(LATCH)


As independent systems, their protective effects work in conjunction with each oth- er.


For information on infants and children traveling with you in the vehicle and re- straint systems for infants and chil- dren, see “Children in the vehicle” (컄 page 69).


60


The 1 indicator lamp in the instrument cluster comes on 앫 for about four seconds when you turn the SmartKey in the starter switch to position 1 or press the KEYLESS-GO* start/stop button once. It then goes out briefly, comes on again and re- mains lit until you start the engine.


앫 for about four seconds when you start the engine by turning the SmartKey or pressing the KEYLESS-GO* start/stop button.


The 1 indicator lamp remains lit if the SmartKey is turned to position 2 and left there or the KEYLESS-GO* start/stop button is pressed twice. The indicator lamp will go out when you start the engine.


The restraint systems are fully operational if the 1 indicator lamp is not lit when the engine is running. A malfunction in the system has been de- tected if the 1 indicator lamp: 앫 fails to extinguish after approximately


four seconds.


앫 does not come on at all. 앫 comes on after the engine was started


or while driving.


For safety reasons, we strongly recom- mend that you visit an authorized Mercedes-Benz Center immediately to have the system checked. For more information, see “Practical hints” (컄 page 297).


Warning!


Airbags


In the event that the 1 indicator lamp comes on during driving or does not come on at all, the SRS self-check has detected a malfunction. For your safety, we strongly recommend that you visit an authorized Mercedes-Benz Center immediately to have the system checked; otherwise the SRS may not be activated when needed in an acci- dent, which could result in serious or fatal injury, or it might deploy unexpectedly and unnecessarily which could also result in injury.


In addition, improper repair work on the SRS creates a risk of rendering the SRS inopera- tive or causing unintended airbag deploy- ment. Work on the SRS must therefore only be performed by qualified technicians. Con- tact an authorized Mercedes-Benz Center.


Warning!


Airbags are designed to reduce the potential of injury and fatality in certain frontal im- pacts (front airbags), side impacts (side im- pact airbags and head protection window curtain airbags) or rollovers (head protec- tion window curtain airbags). However, no system available today can totally eliminate injuries and fatalities.


The activation of the airbags temporarily re- leases a small amount of dust from the air- bags. This dust, however, is neither injurious to your health, nor does it indicate a fire in the vehicle. The dust might cause some tem- porary breathing difficulty for people with asthma or other breathing trouble. To avoid this, you may wish to get out of the vehicle as soon as it is safe to do so. If you have any breathing difficulty but cannot get out of the vehicle after the airbag inflates, then get fresh air by opening a window or door.


Safety and Security Occupant safety


Warning!


To reduce the risk of injury when the front airbags inflate, it is very important for the driver and front passenger to always be in a properly seated position and to wear your seat belts.


For maximum protection in the event of a collision always be in normal seated position with your back against the seat backrest. Fasten your seat belt and ensure that it is properly positioned on your body.


Since the airbag inflates with considerable speed and force, a proper seating and hands on steering wheel position will help to keep you at a safe distance from the airbag. Oc- cupants who are unbelted, out of position or too close to the airbag can be seriously in- jured by an airbag as it inflates with great force in the blink of an eye: 앫 Sit properly belted in a nearly upright


position with your back against the seat backrest.


컄컄


61


Safety and Security Occupant safety


컄컄


앫 Adjust the driver seat as far as possible rearward, still permitting proper opera- tion of vehicle controls. The distance from the center of the driver’s breast- bone to the center of the airbag cover on the steering wheel must be at least ten in (25 cm) or more. You should be able to accomplish this by a combina- tion of adjustments to the seat and steering wheel. If you have any prob- lems, please see an authorized Mercedes-Benz Center.


앫 Do not lean with your head or chest close to the steering wheel or dash- board.


앫 Keep hands on the outside of steering wheel rim. Placing hands and arms in- side the rim can increase the risk and potential severity of hand/arm injury when driver front airbag inflates.


앫 Adjust the front passenger seat as far as possible rearward from the dashboard when the seat is occupied.


앫 Occupants, especially children, should never lean their heads in the area of the door where the side airbag inflates.


62


This could result in serious injuries or death should the airbag be triggered. Always sit nearly upright, properly use the seat belts and appropriate size in- fant or child restraint system.


앫 Children 12 years old and under must never ride in the front seat, except in a Mercedes-Benz authorized BabySmartTM compatible child seat, which operates with the BabySmartTM system installed in the vehicle to deacti- vate the passenger front airbag when it is properly installed. Otherwise they will be struck by the airbag when it inflates in a crash. If this happens, serious or fa- tal injury will result.


Failure to follow these instructions can re- sult in severe injuries to you or other occu- pants.


If you sell your vehicle, it is extremely impor- tant that you make the buyer aware of this safety information. Be sure to give the buyer this Operator’s Manual.


Warning!


Accident research shows that the safest place for children in an automobile is in the rear seat. Should you choose to place a child 12 years old or under in the front passenger seat of your vehicle, you must properly use a BabySmartTM child restraint which will turn off the passenger front airbag. BabySmartTM will not, however, turn off any side impact airbag.


It should be noted that with respect to both front and rear side impact airbags there is a possibility for a side airbag related injury if occupants, especially children, are not prop- erly seated or restrained when next to a side airbag which needs to deploy rapidly in a side impact in order to do its job.


To help avoid the possibility of injury, please follow these guidelines:


(1) Occupants, especially children, should


never place their bodies or lean their heads in the area of the door where the side airbag inflates. This could result in


serious injuries or death should the side airbag be activated.


(2) Always sit nearly upright, properly use the seat belts and use an appropriately sized infant or child restraint system for all children 12 years old or under.


(3) Always wear seat belts properly.


If you believe that, even with the use of these guidelines, it would be safer for your rear seat occupants to have the rear mount- ed side airbags deactivated, then deactiva- tion can be accomplished upon your written request to do so at your authorized Mercedes-Benz Center at an additional cost.


Please contact your local authorized Mercedes-Benz Center or call our Customer Assistance Center at 1-800-FOR-MERCedes (1-800-367-6372) for details.


Airbags are designed to activate only in certain frontal (front airbags) impacts, side impacts (side impact and head protection window curtain airbags) which exceed preset thresholds and in certain rollovers (head protection win- dow curtain airbags). Only during these events will they provide their supple- mental protection. The driver and passengers should al- ways wear their seat belts. Otherwise it is not possible for airbags to provide their supplemental protection. In case of other types of impacts and impacts below airbag deployment thresholds, airbags will not be activat- ed. The driver and passenger will then be protected to the extent possible by a properly fastened seat belt. A proper- ly fastened seat belt is also needed to provide the best possible protection in a rollover.


Safety and Security Occupant safety


We caution you not to rely on the pres- ence of the airbags in order to avoid wearing your seat belt. Your vehicle was originally equipped with airbags that are designed to acti- vate in certain impacts exceeding a preset threshold to reduce the poten- tial and severity of injury. It is important for your safety and that of your passen- gers that you replace deployed airbags and repair any malfunctioning airbags to ensure that the vehicle will continue to provide supplemental crash protec- tion for occupants.


63


Safety and Security Occupant safety


Safety guidelines for the seat belt, emergency tensioning device and airbag


Warning!


앫 Damaged seat belts or belts that were highly stressed in an accident must be replaced and their anchoring points must also be checked. Use only belts in- stalled or supplied by an authorized Mercedes-Benz Center.


앫 Airbags and emergency tensioning de- vice (ETDs) are designed to function on a one-time only basis. An airbag or ETD that was activated must be replaced. 앫 No modifications of any kind may be made to any components or wiring of the SRS. This includes changing or re- moving any component or part of the SRS, the installation of additional trim material, badges, etc. over the steering wheel hub, passenger front airbag cov- er, door trim panels, or door frame trims, and installation of additional elec- trical/electronic equipment on or near


64


SRS components and wiring. Keep area between airbags and occupants free from objects (e.g. packages, purses, umbrellas, etc.).


앫 Do not pass belts over sharp edges.


They could tear.


앫 Do not make any modification that could


change the effectiveness of the belts. 앫 Do not bleach or dye seat belts as this may severely weaken them. In a crash they may not be able to provide ade- quate protection.


앫 Do not hang items such as coat hangers from the coat hooks or handles over the door. These items may turn into projec- tiles and cause head and other injuries when curtain airbag is deployed.


앫 Never place your feet on the instrument panel, dashboard, or on the seat. Always keep both feet on the floor in front of the seat.


앫 An airbag system component within the steering wheel gets hot after the airbag has inflated. Do not touch.


앫 In addition, improper repair work on the SRS creates a risk of rendering the SRS inoperative or causing unintended air- bag deployment. Work on the SRS must therefore only be performed by qualified technicians. Contact an authorized Mercedes-Benz Center.


앫 For your protection and the protection of others, when scrapping the airbag unit or emergency tensioning device, our safety instructions must be fol- lowed. These instructions are available from your authorized Mercedes-Benz Center.


앫 Given the considerable deployment


speed and the textile structure of the airbags, there is the possibility of abra- sions or other injuries resulting from air- bag deployment.


When you sell your vehicle we strongly urge you to give notice to the subsequent owner that it is equipped with an SRS by alerting them to the applicable section in the Operator’s Manual.


Front airbags


1 Driver airbag 2 Passenger airbag Driver and passenger front airbags are de- ployed: 앫 in the event of a frontal impact 앫 if impact exceeds a preset deployment


threshold


앫 independently of the side impact air-


bags


The airbags will not deploy in impacts which do not exceed the system’s deploy- ment thresholds. You will then be protect- ed by the fastened seat belts. The passenger front airbag will only be de- ployed if: 앫 the front passenger seat is occupied 앫 the PASSENGER AIRBAG OFF indicator


lamp in the center console is not lit (컄 page 71)


앫 the impact exceeds a preset deploy-


ment threshold


Do not place objects heavier than 20 lbs (9 kg) on the front passenger seat. This could cause the front or side impact airbag on the front passenger side to deploy in a crash which exceeds the system's deployment threshold.


Safety and Security Occupant safety


Side impact airbags, window curtain airbags


1 Window curtain airbag 2 Side impact airbags The side impact airbags and window cur- tain airbags are deployed: 앫 on the impacted side of the vehicle 앫 in impacts exceeding a preset deploy-


ment threshold


앫 independently of the front airbags


65


Safety and Security Occupant safety


In addition, the window curtain airbags are deployed: 앫 in certain vehicle rollovers The side impact airbags and window cur- tain airbags are not deployed in impacts which do not exceed the system’s deploy- ment threshold. The front passenger side impact airbag will only deploy if the system senses that the front passenger seat is occupied.


Seat belts


When the engine is started, the seat belt telltale < illuminates to remind you and your passengers to fasten your seat belts. If the driver’s seat belt is not fastened be- fore the engine is started, the seat belt telltale < illuminates and a warning chime sounds for approximately six seconds when the engine is started.


66


The use of seat belts and infant and child restraint systems is required by law in all 50 states, the District of Columbia, the U.S. territories and all Canadian provinces. Even where this is not the case, all vehicle occupants should have their seat belts fas- tened whenever the vehicle is in motion. For more information, see “Fastening the seat belts” (컄 page 42).


For information on infants and children traveling with you in the vehicle and re- straint systems for infants and chil- dren, see “Children in the vehicle” (컄 page 69).


Warning!


Always fasten your seat belt before driving off. Always make sure your passengers are properly restrained, even those sitting in the rear and pregnant women.


Failure to wear and properly fasten and po- sition your seat belt greatly increases your risk of injuries and their likely severity in an accident. You and your passengers should always wear seat belts.


If you are ever in an accident, your injuries can be considerably more severe without your seat belt properly buckled. Without your seat belt buckled, you are much more likely to hit the interior of the vehicle or be ejected from it. You can be seriously injured or killed.


In the same crash, the possibility of injury or death is lessened if you are properly wearing your seat belt. Airbags can only protect as they are designed if the occupants are prop- erly wearing their seat belts.


Warning!


Warning!


Warning!


Safety and Security Occupant safety


Never ride in a moving vehicle with the seat backrest in an excessively reclined position as this can be dangerous. You could slide under the seat belt in a collision. If you slide under it, the belt would apply force at the ab- domen or neck. That could cause serious or even fatal injuries. The seat backrest and seat belt provide the best restraint when the wearer is in a nearly upright position and the belt is properly positioned on the body.


Warning!


Never let more people ride in the vehicle than there are seat belts available. Be sure everyone riding in the vehicle is correctly re- strained with a separate seat belt. Never use a seat belt for more than one person at a time.


Damaged seat belts or belts that were highly stressed in an accident must be replaced and their anchoring points must also be checked.


Only use seat belts which have been ap- proved by Mercedes-Benz.


Do not make any modifications to the seat belts. This can lead to unintended activation or to failure.


Do not bleach or dye seat belts as this may severely weaken them. In a crash, they may not be able to provide adequate protection.


Have all work carried out only by qualified technicians. Contact an authorized Mercedes-Benz Center.


USE SEAT BELTS PROPERLY 앫 Seat belts can only work when used


properly. Never wear seat belts in any other way than as described in this sec- tion, as that could result in serious inju- ries in case of an accident.


앫 Each occupant should wear their seat


belt at all times, because seat belts help reduce the likelihood of and potential severity of injuries in accidents, includ- ing rollovers. The integrated restraint system includes SRS (driver airbag, pas- senger front airbag, side impact airbags, head protection window curtain airbags for side windows), ETD (seat belt emer- gency tensioning device), and front seat knee bolsters. The system is designed to enhance the protection offered to properly belted occupants in certain frontal (front airbags and ETD) and side (side impact, window curtain airbags and ETD) impacts which exceed preset deployment thresholds and in certain


컄컄


67


Safety and Security Occupant safety


컄컄


rollovers (window curtain airbags and ETD).


앫 Never wear the shoulder belt under your arm, against your neck or off your shoul- der. In a crash, your body would move too far forward. That would increase the chance of head and neck injuries. The belt would also apply too much force to the ribs or abdomen, which could se- verely injure internal organs such as your liver or spleen.


앫 Never wear belts over rigid or breakable objects in or on your clothing, such as eyeglasses, pens, keys, etc., as these might cause injuries.


앫 Position the lap belt as low as possible on your hips and not across the abdo- men. If the belt is positioned across your abdomen, it could cause serious injuries in a crash.


앫 Never use a seat belt for more than one person at a time. Do not fasten a seat belt around a person and another per- son or other objects.


68


앫 Belts should not be worn twisted. In a crash, you wouldn’t have the full width of the belt to manage impact forces. The twisted belt against your body could cause injuries.


앫 Pregnant women should also use a


lap-shoulder belt. The lap belt portion should be positioned as low as possible on the hips to avoid any possible pres- sure on the abdomen.


앫 Never place your feet on the instrument panel, dashboard or on the seat. Always keep both feet on the floor in front of the seat.


Emergency tensioning device (ETD), seat belt force limiter The seat belts for the front and rear outer seats are equipped with emergency ten- sioning devices and belt force limiters. The ETD is designed to activate in the fol- lowing cases: 앫 in frontal or rear-end impacts exceed-


ing a preset severity level


앫 in certain vehicle rollovers 앫 if the restraint systems are operational and functioning correctly, see 1 in- dicator lamp (컄 page 60).


The ETDs for the front seats will only activate if the respective front seat belt is fastened (latch plate properly insert- ed into buckle). The ETDs for the rear outer seats will activate with or without the respective seat belt fastened.


In an impact, emergency tensioning devic- es remove slack from the belts in such a way that the seat belts fit more snugly against the body. Belt force limiters reduce the force exerted by the seat belts on oc- cupants during a crash.


Warning!


Children in the vehicle


If an infant or child is traveling with you in the vehicle: 앫 Secure the child using an infant or child


restraint appropriate to the age and size of the child.


앫 Make sure the infant or child is proper- ly secured by a belt at all times while the vehicle is in motion.


Infant and child restraint seats and infor- mation on choosing an appropriate re- straint system can be obtained from any Mercedes-Benz Center.


An emergency tensioning device (ETD) that was activated must be replaced.


When disposing of the emergency tension- ing device, our safety instructions must be followed. These are available at your autho- rized Mercedes-Benz Center.


Do not place objects heavier than 20 lbs (9 kg) on the front passenger seat. This could cause the front or side impact airbag on the front passenger side to deploy in a crash which exceeds the system's deployment threshold.


Automatic comfort-fit feature seat belt An automatic comfort-fit feature for front seats reduces the retracting force of the seat belts when they are in normal use.


Safety and Security Occupant safety


Infant and child restraint systems Use only a BabySmartTM1 compatible child restraint for the front passenger seat in this vehicle. We recommend all infants and children be properly restrained at all times while the vehicle is in motion. All lap-shoulder belts except the driver’s seat belt have special seat belt retractors for secure fastening of child restraints. To fasten a child restraint, follow child re- straint instructions for mounting. Then pull the shoulder belt out completely and let it retract. During seat belt retraction, a ratch- eting sound can be heard to indicate that the special seat belt retractor is activated. The belt is now locked. Push down on child restraint to take up any slack. To deactivate, release seat belt buckle and let seat belt retract completely. The seat belt can again be used in the usual man- ner.


1 BabySmart TM is a trademark of Siemens Automo-


tive Corp.


69


Safety and Security Occupant safety


For more information on child seats with mounting fittings for tether an- chorages, see “Installation of infant and child restraint systems” (컄 page 73). For information on LATCH-type child seat mounts (컄 page 74).


Warning!


Never release the seat belt buckle while the vehicle is in motion, since the special seat belt retractor will be deactivated.


The use of infant or child restraints is required by law in all 50 states, the Dis- trict of Columbia, the U.S. territories and all Canadian provinces. Infants and small children should be seated in an appropriate infant or child restraint system properly secured by


70


a lap-shoulder belt or, if so equipped, a child restraint lower anchorage system that complies with U.S. Federal Motor Vehicle Safety Standards 213 and 225 and Canadian Motor Vehicle Safety Standards 213 and 210.2. A statement by the child restraint man- ufacturer of compliance with this stan- dard can be found on the instruction label on the restraint and in the instruc- tion manual provided with the restraint. When using any infant or child restraint system, be sure to carefully read and follow all manufacturer’s instructions for installation and use. Please read and observe warning labels affixed to inside of vehicle and to infant or child restraints.


Warning!


Children 12 years old and under must never ride in the front seat, except in a Mercedes-Benz authorized BabySmartTM1 compatible child seat, which operates with BabySmartTM System installed in the vehicle to deactivate the passenger front airbag when it is properly installed. Otherwise they will be struck by the airbag when it inflates in a crash. If this happens, serious or fatal in- jury will result.


According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seat- ing positions. Infants and small children must ride in back seats and be seated in an appropriate infant or child restraint system, which is properly secured with the vehicle’s seat belt and top tether strap, or secured via lower anchors and top tether strap, fully in accordance with the child seat manufactur- er’s instructions.


1 BabySmart TM is a trademark of Siemens Automo-


tive Corp.


Infants and small children should never share a seat belt with another occupant. During an accident, they could be crushed between the occupant and seat belt.


Children too big for child restraint systems must ride in back seats using regular seat belts. Position shoulder belt across chest and shoulder, not face or neck. A booster seat may be necessary to achieve proper belt positioning for children from 41 lbs until they reach a height where a lap/shoulder belt fits properly without a booster.


A child’s risk of serious or fatal injuries is significantly increased if the child restraints are not properly secured in the vehicle and the child is not properly secured in the child restraint.


When the child restraint is not in use, re- move it from the vehicle or secure it with the seat belt to prevent the child restraint from becoming a projectile in the event of an ac- cident.


Do not leave children unattended in the ve- hicle; even if the children are secured in a child restraint system. Unsupervised chil- dren in a child restraint system may use ve- hicle equipment and cause an accident and/or serious personal injury.


BabySmartTM1 airbag deactivation system


1 Indicator lamp


1 BabySmartTM is a trademark of Siemens Automo-


tive Corp.


Safety and Security Occupant safety


Special BabySmartTM compatible child seats, designed for use with the Mercedes-Benz system and available at any authorized Mercedes-Benz Center are required for use with the BabySmartTM air- bag deactivation system. With the special child seat properly installed, the passenger front airbag will not deploy. The PASSENGER AIRBAG OFF indicator lamp 1 located in the center console will be illuminated, except with the SmartKey removed or in starter switch position 0.


The system does not deactivate the side impact airbag and the emergency tensioning device.


71


Safety and Security Occupant safety


Self-test BabySmartTM1 without special child seat installed After turning the SmartKey in the starter switch to position 1 or 2 or pressing the KEYLESS-GO* start/stop button once or twice, the PASSENGER AIRBAG OFF indi- cator lamp 1 located in the center con- sole comes on for approximately six seconds and then goes out. If the indicator lamp should not come on or is continuously lit, the system is not func- tioning. You must see an authorized Mercedes-Benz Center before seating any child on the front passenger seat. For more information, see “Practical hints” (컄 page 298).


1 BabySmartTM is a trademark of Siemens Automo-


tive Corp.


72


Warning!


Warning!


The BabySmartTM airbag deactivation sys- tem will ONLY work with a special child seat designed to operate with it. It will not work with child seats which are not BabySmartTM compatible.


Never place anything between seat cushion and child seat (e.g. pillow), since it reduces the effectiveness of the deactivation sys- tem. The bottom of the child seat must make full contact with the passenger seat cushion. An incorrectly mounted child seat could cause injuries to the child in case of an accident, instead of protecting the child.


Follow the manufacturer’s instructions for installation of special child seats. When using a BabySmartTM compatible child seat on the front passenger seat, the passenger front airbag will not deploy only if the PASSENGER AIRBAG OFF indicator lamp remains illuminated.


Make sure to check the indicator every time you use the special system child seat. Should the light go out while the restraint is installed, please check installation. If the light remains out, do not use the BabySmartTM restraint to transport children on the front passenger seat until the system has been repaired.


Warning!


Do not place powered-on laptops, cell phones and like electronic devices on the front passenger seat. Signals from such de- vices may interfere with the BabySmartTM system. Such signal interference may cause the PASSENGER AIRBAG OFF indicator lamp not to come on during self-test or be contin- uously lit, indicating that the system is not functioning.


Installation of infant and child restraint systems This vehicle is equipped with tether an- chorages for a top tether strap at each of the rear seating positions.


Head restraint must be positioned such that the top tether strap can pass freely between the head restraint and the top of seat back. Make sure the tether strap is not twisted.


1 Cover of top anchorage ring 왘 Remove cover 1 from anchorage ring. 왘 Store cover 1 in a convenient place


(e.g. glove box).


왘 Guide tether strap between head re-


straint and top of seat back.


2 Hook 3 Anchorage ring 왘 Securely fasten hook 2, which is part


of the tether strap, to anchorage ring 3.


Safety and Security Occupant safety


For safety, make sure the hook 2 has attached to the ring 3 beyond the safety catch, as illustrated.


Once the top tether anchorage hook is at- tached, the child restraint itself can be se- cured. Tighten the top tether strap according to the child restraint manufacturer’s instructions. 왘 Reinstall cover after removing the teth-


er strap.


73


Safety and Security Occupant safety


Child seat anchors – LATCH type This vehicle is equipped with two LATCH (Lower Anchors and Tethers for CHildren) type anchors (at each of the rear seats) for the installation of a LATCH child seat with the matching anchor fittings. If you have not installed a child seat, the LATCH mounting anchor fittings are cov- ered with an upholstery blend.


1 Upholstery blend. 왘 Remove upholstery blend 1 and store


it in the rear center armrest.


74


The child seat must be firmly attached in the right and left side anchor fittings. Non-LATCH type child seats may also be used and can be installed using the vehicle’s seat belt system. Install child seat according to the manufacturer’s instructions.


Warning!


Children too big for child restraint systems must ride in back seats using regular seat belts. Position shoulder belt across chest and shoulder, not face or neck. A booster seat may be necessary to achieve proper belt positioning for children from 41 lbs until they reach a height where a lap/shoulder belt fits properly without a booster.


Install child seat according to manufactur- er’s instructions.


The child seat must be firmly attached in the right and left side anchors 3.


2 Indicates the position of the anchors 3 Anchors 왘 Install child seat according to the man-


ufacturer’s instructions.


Blocking of rear window operation


The override switch is located on the driv- er’s door.


An incorrectly mounted child seat may come loose during an accident which could result in serious injury or death to your child.


Damaged or impact damaged child seats or child seat mounting fittings must be re- placed.


Do not leave children unattended in the ve- hicle, even if the children are secured in a child restraint system.


1 Override switch


Activating override switch 왘 Slide override switch 1 to the right.


A dot becomes visible. The functions in the rear are disabled.


Operation of the rear windows with the switches located in the driver’s door is still possible.


Safety and Security Occupant safety


Warning!


Activate the override switch when children are riding in the back seats of the vehicle. The children may otherwise injure them- selves, e.g. by becoming trapped in the win- dow opening.


When leaving the vehicle, always remove the SmartKey from the starter switch, take the SmartKey with KEYLESS-GO* with you, and lock your vehicle. Do not leave children un- attended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehi- cle equipment can cause an accident and/or serious personal injury.


Deactivating override switch 왘 Slide override switch 1 to the left.


The functions in the rear are enabled again.


For more information on power windows, see “Power windows” (컄 page 186).


75


Activating


왘 Press and hold button 1 for at least


one second.


Deactivating


왘 Press button 1 again. or 왘 Insert SmartKey in the starter switch.


For operation in the USA only: This de- vice complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 앫 This device may not cause harmful


interference, and


앫 this device must accept any inter- ference received, including interfer- ence that may cause undesired operation.


Any unauthorized modification to this device could void the user’s authority to operate the equipment.


Safety and Security Panic alarm 왔 Panic alarm An audible alarm and blinking exterior lamps will operate for approximately 2½ minutes.


1 Â button


76


왔 Driving safety systems In this section you will find information on the following driving safety systems: 앫 ABS (Antilock Brake System) 앫 BAS (Brake Assist System) 앫 ESP (Electronic Stability Program)


In winter operation, the maximum ef- fectiveness of the ABS, BAS, and the ESP is only achieved with winter tires (M+S tires), or snow chains as re- quired.


Safety and Security Driving safety systems


Warning!


ABS


The following factors increase the risk of ac- cidents: 앫 Excessive speed, especially in turns 앫 Wet and slippery road surfaces 앫 Following another vehicle too closely The ABS, BAS and ESP cannot reduce this risk.


Always adjust your driving style to the pre- vailing road and weather conditions.


Warning!


Do not pump the brake pedal. Use firm, steady brake pedal pressure instead. Pump- ing the brake pedal defeats the purpose of the ABS and significantly reduces braking effectiveness.


The Antilock Brake System (ABS) regulates the brake pressure so that the wheels do not lock during braking. This allows you to maintain the ability to steer your vehicle. The ABS is functional above a speed of ap- proximately 5 mph (8 km/h) independent of road surface conditions. On slippery road surfaces, the ABS will re- spond even with light brake pressure.


77


BAS


The Brake Assist System (BAS) operates in emergency situations. If you apply the brakes very quickly, the BAS automatically provides full brake boost, thereby poten- tially reducing the braking distance. Apply continuous full braking pressure until the emergency braking situation is over. The ABS will prevent the wheels from locking. When you release the brake pedal, the brakes function again as normal. The BAS is then deactivated.


Safety and Security Driving safety systems


The - indicator lamp in the instrument cluster comes on when you turn the SmartKey in the starter switch to position 2 or press the KEYLESS-GO* start/stop button twice. It goes out when the engine is running.


Braking At the instant one of the wheels is about to lock up, a slight pulsation can be felt in the brake pedal, indicating that the ABS is in the regulating mode. 왘 Keep firm and steady pressure on the brake pedal while experiencing the pul- sation.


Continuous steady brake pedal pressure yields the advantages provided by the ABS, namely braking power and the ability to steer the vehicle. The pulsating brake pedal can be an indica- tion of hazardous road conditions and functions as a reminder to take extra care while driving.


Emergency brake maneuver 왘 Keep continuous full pressure on the


brake pedal.


Warning!


The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction af- forded. The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, atten- tive, and skillful driver can prevent acci- dents. The capabilities of an ABS equipped vehicle must never be exploited in a reck- less or dangerous manner which could jeop- ardize the user’s safety or the safety of others.


For more information, see “Practical hints” section (컄 page 292).


78


Warning!


ESP


The BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that af- forded by the condition of the vehicle brakes and tires or the traction. The BAS cannot prevent accidents, including those resulting from excessive speed in turns, following an- other vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents. The capabilities of a BAS equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others.


The Electronic Stability Program (ESP) monitors the vehicle's traction (force of adhesive friction between the tires and the road surface) and handling. The ESP recognizes when a wheel is spin- ning or if the vehicle starts to skid. By ap- plying brakes to the appropriate wheel and by limiting engine output, the ESP works to stabilize the vehicle. The ESP is especially useful while driving off and on wet or slip- pery road surfaces. The ESP warning lamp v in the instru- ment cluster flashes when the ESP is en- gaged. The ESP warning lamp v in the instru- ment cluster comes on when you turn the SmartKey in the starter switch to position 2 or press the KEYLESS-GO* start/stop button twice. It goes out when the engine is running.


Safety and Security Driving safety systems


Warning!


Never switch off the ESP when you see the ESP warning lamp v flashing in the in- strument cluster. In this case proceed as fol- lows: 앫 While driving off, apply as little throttle


as possible


앫 While driving ease up on the accelerator 앫 Adapt your speed and driving style to


the prevailing road conditions


Failure to observe these guidelines could cause the vehicle to skid.


The ESP cannot prevent accidents resulting from excessive speed.


79


Safety and Security Driving safety systems


Warning!


The ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded. The ESP cannot prevent accidents, including those resulting from excessive speed in turns, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents. The ca- pabilities of an ESP equipped vehicle must never be exploited in a reckless or danger- ous manner which could jeopardize the us- er’s safety or the safety of others.


Distronic* is switched off when ESP is activated.


80


Because of the ESP’s automatic opera- tion, the engine and ignition must be shut off (SmartKey in starter switch position 0 or 1 or KEYLESS-GO start/stop button* in position 0 or 1) when: 앫 the parking brake is being tested on


a brake test dynamometer


앫 the vehicle is being towed with the


front/rear axle raised


Active braking action through the ESP may otherwise seriously damage the brake system. The ESP will only function properly if you use wheels of the recommended tire size (컄 page 365).


For more information, see “Practical hints” (컄 page 295).


Switching off the ESP


Warning!


The ESP should not be switched off during normal driving other than in the circum- stances described below. Disabling of the system will reduce vehicle stability in stan- dard driving maneuvers.


To improve the vehicle's traction, turn off the ESP in driving situations where it would be advantageous to have the drive wheels spin and thus cut into surfaces for better grip such as: 앫 starting out on slippery surfaces and in


deep snow in conjunction with snow chains


앫 in sand or gravel


Distronic* cannot be activated when the ESP has been deactivated.


If one or more wheels are spinning, the ESP warning lamp v in the speedome- ter flashes, regardless of the speed. Traction control brakes a spinning wheel even when the ESP is deactivated. The ESP always operates when you are braking, even when it has been deactivated.


Avoid spinning of a drive wheel for an extended period with the ESP switched off. This may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty.


Safety and Security Driving safety systems


Warning!


When the ESP warning lamp v is illumi- nated continuously, the ESP is switched off.


Adapt your speed and driving to the prevail- ing road conditions and to the non-operating status of the ESP.


Switching on the ESP 왘 Press the ESP switch 1.


The ESP warning lamp v in the in- strument cluster goes out. You are now again in normal driving mode.


The switch is located on the center con- sole.


1 ESP on/off 왘 Press ESP switch 1 until the ESP


warning lamp v in the speedometer comes on. The ESP is deactivated.


81


Deactivating 앫 With the SmartKey: Inserting the


SmartKey in the starter switch deacti- vates the immobilizer.


앫 With KEYLESS-GO*: Starting the en-


gine by means of the start/stop button on the gear selector lever deactivates the immobilizer.


In case the engine cannot be started (yet the vehicle’s battery is charged), the system is not operational. Contact an authorized Mercedes-Benz Center or call 1-800-FOR-MERCedes (in the USA), or 1-800-387-0100 (in Canada).


Anti-theft alarm system


Once the alarm system has been armed, a visual and audible alarm is triggered when someone: 앫 opens a door 앫 opens the trunk 앫 opens the hood The alarm will stay on even if the activating element (a door, for example) is immedi- ately closed. The alarm system will also be triggered when 앫 someone attempts to raise the vehicle 앫 the vehicle is opened with the


mechanical key


Safety and Security Anti-theft systems 왔 Anti-theft systems Immobilizer


The immobilizer prevents unauthorized persons from starting your vehicle.


Activating 앫 With the SmartKey: Removing the


SmartKey from the starter switch acti- vates the immobilizer.


앫 With KEYLESS-GO*: Turning off the en- gine by means of the start/stop button on the gear selector lever activates the immobilizer.


82


Safety and Security Anti-theft systems


If the alarm stays on for more than 20 seconds, an emergency call is initi- ated automatically by the Tele Aid sys- tem (컄 page 230) provided Tele Aid service was subscribed to and properly activated, and that necessary cellular service and GPS coverage are avail- able.


Arming the alarm system The alarm system is armed after locking the vehicle with the SmartKey or KEYLESS-GO*. The turn signal lamps flash three times to indicate that the alarm sys- tem is activated. The indicator lamp in the central locking switch (컄 page 106) will flash after approximately ten seconds when the alarm system is completely armed .


If the turn signal lamps do not flash three times one of the following ele- ments may not be properly closed: 앫 a door 앫 the trunk lid 앫 the hood Close the respective element and lock the vehicle again.


Disarming the alarm system The alarm system is disarmed when you unlock your vehicle with the SmartKey or KEYLESS-GO*. The turn signal lamps flash once to indicate that the alarm system is deactivated.


Canceling the alarm To cancel the alarm:


With the SmartKey 왘 Insert the SmartKey in the starter


switch.


or 왘 Press the Œ or ‹ button on the


SmartKey.


With KEYLESS-GO* 왘 Grasp the outside door handle. or 왘 Press the KEYLESS-GO* start/stop


button.


83


Safety and Security Anti-theft systems


Tow-away alarm


Once the tow-away alarm is armed, a visual and audible alarm will be triggered when someone attempts to raise the vehicle.


The tow-away protection alarm is trig- gered, for example, if the vehicle is lift- ed on one side. If the alarm stays on for more than 20 seconds, an emergency call is initi- ated automatically by the Tele Aid sys- tem (컄 page 230) provided Tele Aid service was subscribed to and properly activated, and that necessary cellular service and GPS coverage are avail- able.


Arming tow-away alarm When you lock your vehicle, the tow-away alarm is automatically armed after about 30 seconds. When you unlock your vehicle, the tow-away protection disarms automatical- ly.


Disarming tow-away alarm To prevent triggering the tow-away alarm, switch off the tow-away alarm feature be- fore towing the vehicle, or when parking on a surface subject to movement, such as a ferry or auto train.


The switch is located on the center con- sole.


1 Indicator lamp 2 Tow-away alarm off switch 왘 Switch off the ignition and remove the


SmartKey.


You cannot disarm the tow-away alarm if the ignition is switched on.


84


왘 Press switch 2.


Indicator lamp 1 in the switch comes on briefly.


왘 Exit and lock your vehicle with the


SmartKey or (vehicles with KEYLESS-GO*) the lock button at each door handle.


The tow-away alarm remains disarmed un- til you lock your vehicle again.


Canceling tow-away alarm To cancel the alarm:


With the SmartKey 왘 Insert the SmartKey in the starter


switch.


or 왘 Press the Œ or ‹ button on the


SmartKey.


Safety and Security Anti-theft systems


With KEYLESS-GO* 왘 Grasp the outside door handle. or 왘 Press the KEYLESS-GO* start/stop


button.


85


86


Controls in detail Locking and unlocking


Seats


Memory function


Lighting


Instrument cluster


Control system


Automatic transmission


Good visibility


Automatic climate control


Power windows


Sliding/pop-up roof


Driving systems


Loading


Useful features


87


Controls in detail Locking and unlocking


In the “Controls in detail” section you will find detailed information on how to oper- ate the equipment installed in your vehicle. If you are already familiar with the basic functions of your vehicle, this section will be of particular interest to you. To quickly familiarize yourself with the ba- sic functions of the vehicle, refer to the “Getting started” section of this manual. The corresponding page numbers are giv- en at the beginning of each segment.


Locking and unlocking


왔 SmartKey


Your vehicle comes supplied with two SmartKeys, each with remote control and a removable mechanical key. The locking tabs for the mechanical key portion of the two SmartKeys are a different color to help

Loading...
x