2010 Jeep Wrangler Owners Manual

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199
11. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window.

200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

12. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the Velcro威 along the top and rear of the window. Repeat this step for the opposite side.

1 — Incorrect Insertion 2 — Correct Insertion

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201
13. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed.

202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 14. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage.

15. Run the zipper fully around to the right side of the window.

16. Grasp the swing gate bar and position it into the swing gate brackets.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203
18. Close the header latches and return the sun visors to their secured position.

17. Apply downward pressure on the top corner of the rear soft top bow (3–bow), then complete attaching the sail panel retainers into the body side channel.

SOFT TOP (FOUR-DOOR MODELS) Please visit the owner’s section of Jeep.com for instruc- tional videos.

204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!

The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ing, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any addi- tional loads other than environmental (rain, snow, etc.).

If the temperature is below 72°F (24°C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up. This is caused by a natural contraction of the vinyl coating on the fabric top. Place the vehicle in a warm area. Pull steadily on the top fabric. The vinyl will stretch back to its original size and

the top can then be snapped into place. If the tempera- ture is 41°F (5°C) or below, do not attempt to put the top down or roll the rear or side curtains.

CAUTION!

• Do not run a fabric top through an automatic car wash. Window scratches and wax buildup may result. • Do not lower the top when the temperature is below 41°F (5°C). Damage to the top may result. • Do not lower the top when the windows are dirty. • Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered. • Do not lower the top with the windows installed.

Grit may scratch the window.

Window and top damage may occur.

(Continued)

CAUTION! (Continued)

• Refer to “Appearance Care for Fabric Top Models” in “Maintaining Your Vehicle” for further infor- mation. It contains important information on cleaning and caring for your vehicle’s fabric top. • Do not use any tools (screwdrivers, etc.) to pry or force any of the clamps, clips, or retainers securing the soft top. Do not force or pry the soft top framework when opening or closing. Damage to the top may result.

WARNING!

• Do not drive the vehicle with the rear window curtain up unless the side curtains are also open. Dangerous exhaust gases which can kill could enter the vehicle.

(Continued)

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205

WARNING! (Continued)

• The fabric upper doors and fabric top are designed only for protection against the elements. Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident. Remember, always wear seat belts.

CAUTION!

Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • It is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior. (Continued)

206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION! (Continued)

• Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle’s interior. • The soft top must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior.

NOTE: Do not remove any of the three attachment knobs unless you are planning on installing the hard top.

Quick Steps for Lowering the Soft Top

2. Release header latches from the windshield frame.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207

1. Remove the side and back windows.

208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Fold header rearward, pulling the fabric to the rear.

4. Release Sunrider威 latch (both sides).

5. Open the swing gate and lower the top.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209

NOTE: Ensure the fabric does not overhang the sides of the vehicle.

210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Quick Steps for Raising the Soft Top

1. Open the swing gate and raise the top, engaging the Sunrider威 latches (another person may be needed to help with this operation).

2. Install rear corner panels.

3. Rotate the header forward.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211

212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Engage the header latches.

5. Install the side and back windows.

Folding Down The Soft Top

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213

1 — Header Bow 2 — 2–Bow 3 — 3–Bow 4 — 4–Bow 5 — Sail Panel

6 — Body Side Retainer 7 — Quarter Window 8 — Check Strap 9 — Front Retainer — Quarter Window 10 — Bottom Retainer — Quarter Window

214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

1 — Zipper Start 2 — Zipper Finish 3 — Swing Gate Bar 4 — Swing Gate Brackets 5 — Sail Panels

NOTE: Clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. If your vehicle has half-doors, remove each half-door window by opening the door and lifting the half-door window out. NOTE: Stow half-door windows carefully outside of the vehicle, never inside, to avoid scratches. 2. Unclip and move the sun visors to the side. 3. Release the header latches and hooks from the loops on the windshield frame.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215

4. Open the swing gate.

216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets.

• Unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across the top and down to the left lower corner. Zipper pulls will stay on the rear window. Pull down on the rear window to disengage it from the zipper on the top cover. Stow the windows carefully to avoid scratch- ing.

6. Undo the Velcro威 that runs along the top and rear edge of the side window. 7. Beginning from the rear lower corner, completely unzip the window.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217
9. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle.

8. Once unzipped, remove the side window retainers from the door channel and body side channel. Repeat this step on the opposite side.

NOTE: When releasing the sail panel retainers, it is helpful to pull down on the rear roof bow.

218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 10. Fold the sail panels so that they rest on top of the soft top.

11. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage.

12. Grasp the front side bow behind the header, and lift the top.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219
13. Fold back the front section of the top, pulling the fabric rearward. Gently rest the header on top of the rear portion of the deck.

220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 14. Fold the top so that the material forms a ⬙W⬙ as shown. Enter the vehicle and move the material into two folds.

15. Release the side bows by pressing down on the latch above the front of the rear door. Push the top rearward to disengage. Repeat this step on the other side.

16. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake light. Grasp the folded side bows and slide the top along the door frame track to the rear door frame.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221
NOTE: Help from another person will ease this opera- tion.

17. Gently slide the side bows off the door frame track and lower the top down into the vehicle.

18. Tuck the fabric and the check straps between the bows as far inside as possible. This will keep any portion of the top from flapping outside of the vehicle. 19. Once the top is fully down, use the Velcro威 straps provided to secure the top to the vehicle by wrapping the

222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE strap around the side bows and through the slot on the body.

20. Close the front header latches. 21. Remove the door frames, if desired. Refer to “Door Frame” in this section for further information. Putting Up The Soft Top

NOTE: Be extremely careful when putting up the soft top to prevent the doors from getting scratched. It may be helpful to open the rear doors. 1. Install the door frames, if removed. Refer to “Door Frame” in this section for further information. 2. Undo the straps used to secure the top in the down position and store in secure location. 3. Open the swing gate.

4. Grasp the folded side bows and lift to the top of the rear door frames. NOTE: Help from another person will ease this opera- tion.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223
5. Insert the slider feature of the knuckles into the door frame tracks and slide the top forward.

224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Ensure that the top locks into the Sunrider威 locking mechanisms that are located above the front of the rear doors.

8. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame.

7. Unclip and move the sun visors to the side.

9. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225
10. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel until it snaps onto the exterior part of the rail. To be properly located, the bracket must only be clipped to the shortened rail edge.

226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 11. Ensure that the straps are positioned correctly before pulling the sail panels over the rear roof bow (4–bow).

Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (4–bow) will aid in reaching the channel with the retainers.

12. To install the side windows, affix the window tem- porarily by attaching it to the Velcro威 in the upper rear corner. Start the zipper but close only about 1 in (2.5 cm).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227
13. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window.

228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

14. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the Velcro威 along the top and rear of the window. Repeat this step for the opposite side.

1 — Incorrect Insertion 2 — Correct Insertion

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229
15. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed.

230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 16. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage.

17. Run the first zipper fully around to the right side of the window. 18. Grasp the swing gate bar and position it into the swing gate brackets.

19. Complete the installation of the sail panel by insert- ing the rest of the retainer into the body channel. 20. Close the header latches and return the sun visors to their secured position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231

SUNRIDER姞 (TWO-DOOR MODELS) — IF EQUIPPED

CAUTION!

Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior.

If you are going to be driving faster than 40 mph NOTE: (64 km/h) with the Sunrider威 feature open, it is recom- mended that you remove the rear window of the vehicle.

232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening the Sunrider姞

1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame.

3. Slide the plastic sleeve forward.

4. Grasp the header and lift the top back. Make sure the material is folded back as shown. NOTE: The Sunrider威 latch on the door rail should not be activated for Sunrider威 use. If activated, the soft top must be reinstalled starting from the sail panels.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233
5. Locate the straps to secure the side bows. Wrap the straps around the bows as shown. Repeat on the other side.

6. Reposition the sun visors.

234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Closing the Sunrider姞

1. Remove the straps from the side bows. 2. Unclip and move the sun visors to the side. 3. Grasp the front header and pull it to the front of the vehicle. 4. Hook the header latches to the loops on the wind- shield frame, close latches, and return the sun visors to their original positions. 5. Slide the plastic sleeve rearward over the Sunrider威 link.

SUNRIDER姞 (FOUR-DOOR MODELS) — IF EQUIPPED

CAUTION!

Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior.

If you are going to be driving faster than 40 mph NOTE: (64 km/h) with the Sunrider威 feature open, it is recom- mended that you remove the rear window of the vehicle.

Opening the Sunrider姞

1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235
3. Grasp the front side bow behind the header, and lift the top.

236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Fold back the front section of the top and gently rest the header on top of the rear portion of the deck.

5. Fold the top so that the material forms a ⬙W⬙ as shown. Enter the vehicle and move the material into two folds.

6. Secure the top by using the two provided straps. Each strap will wrap around the side bow and Velcro威 to itself; use one strap on each side of the vehicle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237

Closing the Sunrider姞 Perform the above steps in the opposite order. NOTE: Failure to fold the fabric rearward will allow the material to sag and may block the rearview mirror.

238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES — HARD TOP ONLY

Rear Window Wiper/Washer — If Equipped A rotary switch on the center portion of the control lever (located on the right side of the steering column) controls the operation of the rear wiper/washer function.

Rotate the switch upward to the first detent posi- tion for rear wiper operation. Rotate the switch upward past the first detent to activate the rear washer. The washer pump will continue to operate as long as the switch is held. Upon release, the wiper will cycle two to three times before returning to the set position. If the rear wiper is operating when the ignition is turned to the LOCK position, the wiper will automatically return to the “Park” position. When the vehicle is restarted, the wiper will resume function at whichever position the switch is set at.

Rear Wiper/Washer Control

Rear Window Defroster — If Equipped

The rear window defroster button is located on the bottom right-side of the blower control knob. Press this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time. NOTE: To prevent excessive battery drain, use the rear window defroster only when the engine is operating.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239

CAUTION!

Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abra- sive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window.

UNDERSTANDING YOUR INSTRUMENT PANEL

CONTENTS

䡵 Instrument Panel Features . . . . . . . . . . . . . . . 244
䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 245
䡵 Instrument Cluster Descriptions . . . . . . . . . . . 246
䡵 Compass And Trip Computer — If Equipped . . 261
▫ Control Buttons . . . . . . . . . . . . . . . . . . . . . 261
▫ Trip Conditions . . . . . . . . . . . . . . . . . . . . . 262
▫ Compass/Temperature Display . . . . . . . . . . 263

▫ Operating Instructions - Radio Mode . . . . . . 267
▫ Operation Instructions - (Disc Mode For CD

And MP3/WMA Audio Play, DVD-Video) . . . 275
▫ Notes On Playing MP3/WMA Files . . . . . . . 277
▫ List Button (Disc Mode For MP3/WMA

Play)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280

▫ Info Button (Disc Mode For MP3/WMA

Play)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280

䡵 Media Center 230 (REQ) — AM/FM Stereo

Radio And 6–Disc CD/DVD Changer (MP3/WMA AUX Jack) . . . . . . . . . . . . . . . . . . 267

䡵 Media Center 730N/430 (RER/REN/RBZ) — AM/FM Stereo Radio And CD/DVD/HDD/ NAV — If Equipped . . . . . . . . . . . . . . . . . . . . 282

242 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions — Voice Command

System — If Equipped . . . . . . . . . . . . . . . . . 283

▫ Operating Instructions — Uconnect™ Phone

— If Equipped . . . . . . . . . . . . . . . . . . . . . . 283
▫ Clock Setting Procedure — RBZ Radio . . . . . 283
▫ Clock Setting Procedure — RER/REN

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285

䡵 Media Center 130 (RES) — AM/FM Stereo

Radio With CD Player (MP3 AUX Jack). . . . . . . 287
▫ Operating Instructions — Radio Mode . . . . . 287
▫ Operation Instructions — CD Mode For CD

And MP3 Audio Play . . . . . . . . . . . . . . . . . 290
▫ Notes On Playing MP3 Files . . . . . . . . . . . . 292
▫ Operation Instructions - Auxiliary Mode . . . . 295

䡵 Media Center 130 (RES/RSC) — AM/FM

Stereo Radio With CD Player (MP3 AUX Jack) And Sirius Radio . . . . . . . . . . . . . . . . . . . . . . 295
▫ Operating Instructions — Radio Mode . . . . . 296
▫ Operation Instructions — CD Mode For CD

And MP3 Audio Play . . . . . . . . . . . . . . . . . 301
▫ Notes On Playing MP3 Files . . . . . . . . . . . . 303
▫ List Button (CD Mode For MP3 Play) . . . . . . 306
▫ Info Button (CD Mode For MP3 Play) . . . . . . 306
▫ Uconnect™ Multimedia (Satellite Radio)

— If Equipped . . . . . . . . . . . . . . . . . . . . . . 307

䡵 Uconnect™ Multimedia (Satellite Radio)

— If Equipped (REN/REQ/RER/RES/REU/ RBZ Radios Only) . . . . . . . . . . . . . . . . . . . . . . 311
▫ System Activation . . . . . . . . . . . . . . . . . . . . 312

▫ Electronic Serial Number/Sirius

Identification Number (ESN/SID) . . . . . . . . . 312

▫ Selecting Uconnect™ Multimedia (Satellite)

Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . 313
▫ Reception Quality . . . . . . . . . . . . . . . . . . . . 313
▫ Operating Instructions — Uconnect™

Multimedia (Satellite) Mode . . . . . . . . . . . . . 313

▫ Operating Instructions — Uconnect™ Phone

(If Equipped)

. . . . . . . . . . . . . . . . . . . . . . . 316

▫ Operating Instructions — Video

Entertainment System (VES)™ (If Equipped) . 316

UNDERSTANDING YOUR INSTRUMENT PANEL 243
䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . 316
䡵 Radio Operation And Cellular Phones . . . . . . . 317
䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 317
▫ Manual Heater Only . . . . . . . . . . . . . . . . . . 317
▫ Manual Heating And Air Conditioning

System — If Equipped . . . . . . . . . . . . . . . . . 319
▫ Air Conditioning . . . . . . . . . . . . . . . . . . . . 323
▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . 324

244 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES

1 — Air Outlet 2 — Instrument Cluster 3 — Horn 4 — Radio 5 — Glove Compartment

6 — Climate Controls 7 — Power Outlet 8 — Lower Switch Bank 9 — Auxiliary Power Outlet / Cigar Lighter

INSTRUMENT CLUSTER

UNDERSTANDING YOUR INSTRUMENT PANEL 245

246 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS

1. Fuel Gauge The pointer shows the level of fuel in the fuel tank. NOTE: When the ignition switch is turned to OFF, the fuel gauge and temperature gauge may not show accu- rate readings. When the engine is not running, turn the ignition switch to ON to obtain accurate readings. 2. Charging System Light

This light shows the status of the electrical charg- ing system. The light should come on when the ignition switch is first turned ON, and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an autho- rized dealer.

If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”. 3. Front Fog Light Indicator — If Equipped

This indicator will illuminate when the front fog lights are on.

4. Low Fuel Warning Light

When the fuel level reaches approximately 2.8 gal (10.6L) this light will turn on and a single chime will sound.

5. Speedometer Indicates vehicle speed. 6. Front Axle Lock Indicator — If Equipped

Indicates when the front axle lock has been activated.

7. Seat Belt Reminder Light

A warning chime and an indicator light will alert you to buckle the seat belts. When the belt is buckled, the chime will stop, but the light will stay on for about six seconds, until it times out. Refer to “Occupant Restraints” in “Things To Know Before Start- ing Your Vehicle” for further information. 8. Turn Signal Indicators

The arrows will flash with the exterior turn signals when the turn signal lever is operated. A tone will chime if the turn signals are left on for more than 1 mile (1.6 km). 9. Oil Pressure Warning Light

This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started, if the bulb does not come on, have the system checked by an authorized dealer. If the light turns on

UNDERSTANDING YOUR INSTRUMENT PANEL 247
while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood. 10. High Beam Indicator

This indicator shows that the high beam head- lights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever towards you to switch the headlights back to low beam. If the driver’s door is open, and the headlights or park lights are left on, the high beam indicator light will remain illuminated and a chime will sound.

248 UNDERSTANDING YOUR INSTRUMENT PANEL 11. Brake Warning Light

This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Program (ESP) sys- tem. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop.

The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected. NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces- sary.

WARNING!

Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately.

Vehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approxi- mately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer.

UNDERSTANDING YOUR INSTRUMENT PANEL 249
The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 12. Anti-Lock Brake (ABS) Light

After the ignition is turned on, the Anti-Lock Brake System (ABS) light illuminates to indicate function check at vehicle start-up. If the light remains on after start-up or comes on and stays on at road speeds, it may indicate that the ABS has detected a malfunction or has become inoperative. The system reverts to standard non-anti-lock brakes. If both the Brake Warning Light and the ABS Warning Light are on, see an authorized dealer immediately. Refer to “Anti-Lock Brake System” in “Starting And Operat- ing”.

250 UNDERSTANDING YOUR INSTRUMENT PANEL 13. Airbag Warning Light

This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is either not on during starting, stays on, or turns on while driving, then have the system inspected at an authorized dealer as soon as possible. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information. 14. Rear Axle Lock Indicator — If Equipped

This light indicates when the rear axle lock has been activated.

15. Tachometer Indicates the engine speed in revolutions per minute (RPM).

CAUTION!

Do not operate the engine with the tachometer pointer in the red area. Engine damage will occur.

16. Engine Temperature Warning Light

This light warns of an overheated engine condi- tion. If the engine is critically hot, a warning chime will sound 10 times. After the chime turns off, the engine will still be critically hot until the light goes out. 17. Vehicle Security Light — If Equipped

This light will flash at a fast rate for approxi- mately 15 seconds, when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed.

18. Temperature Gauge The temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range.

CAUTION!

Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately, and call an authorized deal- ership for service.

UNDERSTANDING YOUR INSTRUMENT PANEL 251

WARNING!

A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer- ship for service if your vehicle overheats. If you decide to look under the hood yourself, see “Main- taining Your Vehicle”. Follow the warnings under the Cooling System Pressure Cap paragraph.

19. Cruise Indicator

This indicator shows when the electronic speed control system is turned on.

20. 4WD Indicator Light — If Equipped

This light alerts the driver that the vehicle is in the four-wheel drive mode, and the front and rear driveshafts are mechanically locked to- gether forcing the front and rear wheels to

rotate at the same speed.

252 UNDERSTANDING YOUR INSTRUMENT PANEL 21. Odometer / Trip Odometer / ECO (Fuel Saver Indicator) Button Press this button to change the display from odometer to either of the two trip odometer settings or the “ECO” display. Trip A or Trip B will appear when in the trip odometer mode. Press and hold the button for two seconds to reset the trip odometer to 0 miles or kilome- ters. The odometer must be in trip mode to reset. 22. Shift Lever Indicator The Shift Lever Indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. 23. Tire Pressure Monitoring Telltale Light

Each tire, including the spare (if provided), should be checked monthly, when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle

has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to

maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more

UNDERSTANDING YOUR INSTRUMENT PANEL 253
tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.

CAUTION!

The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can, or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.

254 UNDERSTANDING YOUR INSTRUMENT PANEL 24. Odometer / Trip Odometer Display Area The odometer shows the total distance the vehicle has been driven. The trip odometer shows individual trip mileage. Refer to “Odometer / Trip Odometer / ECO (Fuel Saver Indicator) Button” for additional information. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. If your odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service. If s/he cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/ service, so that you can be sure that it is properly reset, or that the door jamb sticker is accurate if the odometer must be reset at zero.

Vehicle Odometer Messages When the appropriate conditions exist, the following odometer messages will display:

ECO . . . . . . . . . . . . . . . . . . . Fuel Saver Indicator Off ECO-ON . . . . . . . . . . . . . . . . Fuel Saver Indicator On door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Ajar gATE . . . . . . . . . . . . . . . . . . . . . . . . . . . Liftgate Ajar LoW tirE. . . . . . . . . . . . . . . . . . . . . Low Tire Pressure HOTOIL . . . . . . . . . . . . Transmission Oil Temperature Above Normal Limits gASCAP . . . . . . . . . . . . . . . . . . . . . . . Fuel Cap Fault noFUSE . . . . . . . . . . . . . . . . . . . . . . . . . . Fuse Fault CHAngE OIL . . . . . . . . . . . . . . . Oil Change Required ESPOFF . . . . . . . . . . . . . . . . . . . . . . ESP Deactivated ECO / ECO-ON (Fuel Saver Indicator) — If Equipped The ECO-ON indicator will illuminate when you are driving in a fuel efficient manner and can be used to modify driving habits in order to increase fuel economy.

The ECO display will toggle between ECO and ECO-ON depending on driving habits and vehicle usage. Press the Odometer / Trip Odometer / ECO (Fuel Saver Indicator) button to change the display from odometer to either of the two trip odometer settings or the “ECO” display. LoW tirE When the appropriate condition exists, the odometer display will toggle between LoW and tirE for three cycles. “HOTOIL” Transmission Temperature Warning Message The “HOTOIL” cluster message will appear in the odom- eter accompanied with a chime to indicate that there is excessive transmission fluid temperature that might oc- cur with severe usage such as trailer towing. It may also occur when operating the vehicle in a high torque converter slip condition, such as 4-wheel drive operation

UNDERSTANDING YOUR INSTRUMENT PANEL 255
(e.g., snow plowing, off- road operation). If this “HOT- OIL” message turns on, stop the vehicle and run the engine at idle or faster, with the transmission in NEU- TRAL until the message turns off.

CAUTION!

Continuous driving with the Transmission Tempera- ture “HOTOIL” Warning message illuminated will eventually cause severe transmission damage or transmission failure.

WARNING!

Continued operation with the Transmission Tem- perature “HOTOIL” Warning message illuminated could cause the fluid to boil over, come in contact with hot engine or exhaust components causing a fire that may result in personal injury.

256 UNDERSTANDING YOUR INSTRUMENT PANEL gASCAP If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gASCAP” message will display in the odometer display area. Tighten the fuel filler cap properly and press the TRIP ODOMETER button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. noFUSE If the vehicle diagnostic system determines that the Ignition Off Draw (IOD) fuse is improperly installed, or damaged, a “noFUSE” message will display in the odom- eter display area. For further information on fuses and fuse locations refer to “Fuses” in “Maintaining Your Vehicle”.

CHAngE OIL Message Your vehicle is equipped with an engine oil change indicator system. The “CHANgE OIL” message will flash in the instrument cluster odometer for approximately 12 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty-cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the Trip Odometer button on the instrument cluster. To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure:

1. Turn the ignition switch to the ON position (Do not start the engine). 2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the OFF/LOCK position. If the indicator message illuminates when you NOTE: start the vehicle, the oil change indicator system did not reset. If necessary repeat this procedure. 25. Malfunction Indicator Light (MIL)

The Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission con- trol systems. The light will illuminate when the ignition is in the ON position, before engine start. If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly.

UNDERSTANDING YOUR INSTRUMENT PANEL 257
Certain conditions such as a loose or missing gas cap, poor quality fuel, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing. When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs.

CAUTION!

Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.

258 UNDERSTANDING YOUR INSTRUMENT PANEL

WARNING!

A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants or wood or cardboard, etc. This could result in death or serious injury to the driver, occu- pants or others.

26. Electronic Stability Control (ESC) Activation/ Malfunction Indicator Light — If Equipped

The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON position. It should go out with the engine running. If the “ESC Activation/Malfunction Indicator Light” comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this

light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as possible to have the problem diagnosed and corrected. NOTE: • The “ESC Off

Indicator Light” and the “ESC Activation/Malfunction Indicator Light” come on mo- mentarily each time the ignition switch is turned ON. • Each time the ignition is turned ON, the ESC system • The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive following the maneuver that caused the ESC activation.

will be ON even if it was turned off previously.

WARNING!

The Electronic Stability Control (ESC) cannot pre- vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ESC cannot prevent acci- dents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydro- planing. Only a safe, attentive, and skillful driver can prevent accidents. The capabilities of an ESC- equipped vehicle must never be exploited in a reck- less or dangerous manner which could jeopardize the user’s safety or the safety of others.

27. O/D (Overdrive) Off Indicator Light

This light will illuminate when the O/D OFF button has been selected and overdrive has been turned off. The O/D OFF button is located on the center console.

UNDERSTANDING YOUR INSTRUMENT PANEL 259

28. Sway Bar Indicator Light — If Equipped

This indicator will illuminate when the front sway bar is disconnected.

29. Electronic Stability Program (ESP) / Brake Assist System (BAS) Warning Light

The Electronic Stability Program (ESP) / Brake Assist System (BAS) warning light in the in- strument cluster comes on when the ignition switch is turned to the ON position. The light should go out with the engine running. If the ESP/BAS warning light comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system. If this light stays illuminated, have the ESP and BAS checked at an authorized dealer as soon as possible. Refer to “Electronic Brake Control System” in “Starting And Operating” for further infor- mation.

260 UNDERSTANDING YOUR INSTRUMENT PANEL

WARNING!

If a warning light remains on the system may not be working and you will not have the benefit of ESP or BAS. Under certain driving conditions, where ESP or BAS would be beneficial, you - if you have not adjusted your driving speeds and stopping in or to account for the lack of the feature, may be in acci- dent.

30. Electronic Throttle Control (ETC) Light

This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected while the engine is run- ning, the light will either stay on or flash depending on the nature of the problem. Cycle the ignition key when the vehicle is safely and completely stopped and the shift lever is placed in the PARK position. The light should turn off. If the light remains on

with the engine running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible. If the light continues to flash when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing. The light will come on when the ignition is first turned ON and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an autho- rized dealer. 31. Compass / Mini-Trip Computer Display — If Equipped When the appropriate conditions exist, this display shows the Mini-Trip Computer messages. Refer to “Mini- Trip Computer”.

32. Compass / Mini-Trip Computer Button—If Equipped Press this button to switch between the different functions.

COMPASS AND TRIP COMPUTER — IF EQUIPPED The Compass/Trip Computer is located in the instru- ment cluster. It features a driver-interactive display (dis- plays information such as outside temperature, compass direction, and trip information).

UNDERSTANDING YOUR INSTRUMENT PANEL 261

Compass/Trip Computer Display

Control Buttons

NOTE: The system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated tempera- ture is displayed. Engine temperature can also affect the

262 UNDERSTANDING YOUR INSTRUMENT PANEL displayed temperature, therefore temperature readings are not updated when the vehicle is not moving. Press and release the left button (on the instrument cluster) to access the computer displays. Press and hold the left button (on the instrument cluster) for two to three seconds to switch from English to Metric displays. Reset / Change Display Press and hold the left button (on the instrument cluster) while function is being displayed to reset or change the display. The following trip displays can be reset or changed: • AVG ECO (changes to present fuel economy) • ET (will reset display)

Trip Conditions

Average Fuel Economy (AVG ECO) This display shows the average fuel economy. Estimated Range (DTE) This display shows the estimated distance that can be traveled with the fuel remaining in the tank. This esti- mated distance is based on the most recent trip informa- tion: (Average Fuel Economy) x (Fuel Remaining). This display cannot be reset. Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset.

Trip Odometer (ODO) / ECO (Fuel Saver Indicator) — If Equipped This display shows the distance traveled since the last reset. Press and release the right button (on the instru- ment cluster) to switch from odometer, to Trip A or Trip B, or to ECO. Press and hold the right button while the odometer/trip odometer is displayed to reset. Trip A Shows the total distance traveled for Trip A since the last reset. Trip B Shows the total distance traveled for Trip B since the last reset. ECO (Fuel Saver Indicator) — If Equipped The ECO-ON indicator will illuminate when you are driving in a fuel efficient manner and can be used to modify driving habits in order to increase fuel economy.

UNDERSTANDING YOUR INSTRUMENT PANEL 263
The ECO display will toggle between ECO and ECO-ON depending on driving habits and vehicle usage. Compass/Temperature Display

If the vehicle is equipped with a Chrysler NOTE: Uconnect™ gps (Navigation Radio), the NAV system will provide the compass direction, and the variance and calibration menus will be unavailable. The compass will perform accurately, based on GPS signals instead of the Earth’s magnetic field. This display provides the outside temperature and one of eight compass readings to indicate the direction the vehicle is facing.

264 UNDERSTANDING YOUR INSTRUMENT PANEL

WARNING!

Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.

Compass Calibration The compass on your vehicle will automatically calibrate when new, and will continuously adjust itself over the life of the vehicle. If the CAL indicator is on (or flashing), drive slowly (under 10 mph [16 kmh]) in an open area until the CAL indicator is off. NOTE: • A good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc.

• Magnetic and battery powered devices, (such as cell phones, iPod’s, radar detectors, PDA’s and laptops) should be kept away from the top of the instrument panel. This is where the compass module is located and such devices may interfere and cause false com- pass readings.

Automatic Compass Calibration The self-calibrating feature of the compass eliminates the need to calibrate the compass for normal conditions. During a short initial period, the compass may appear erratic and the CAL symbol will appear (blinking) on the display. After the vehicle has completed at least one complete circle under 5 mph (8 km/h) in an area free from large metal objects, calibration will be complete when the CAL symbol is extinguished. After initial calibration, the compass will continue to automatically update this calibration whenever the ve- hicle is in motion.

Manual Compass Calibration

NOTE: Before attempting a manual compass calibra- tion, the engine must be running and the transmission in the PARK position (if equipped). If the compass appears erratic or inaccurate and the variance has been properly set, you may wish to manu- ally recalibrate the compass. To manually calibrate the compass: 1. First enter the variance mode. Press and hold the left button (located on the instrument cluster) for approxi- mately 10 seconds to enter the variance mode, and release the button when the VAR (Compass Variance) symbol appears. 2. The current variance value will also be displayed. Once in the variance mode, it is necessary to release the button, and then press and hold it again (approximately 10 seconds) until CAL is displayed (solid, not blinking).

is no longer displayed,

UNDERSTANDING YOUR INSTRUMENT PANEL 265
3. Manual compass calibration has been initiated. Drive the vehicle slowly in one or more circles under 5 mph (8 km/h) in an area free from large metal objects until the CAL symbol is extinguished. When the CAL symbol the compass is calibrated and should display correct head- ings. Verify proper calibration by checking North (N), South (S), East (E), and West (W). If the compass does not appear accurate, repeat the calibration procedure in an- other area. Compass Variance (VAR) Compass Variance is the difference between Magnetic North and Geographic North. To ensure compass accu- racy, the compass variance should be properly set accord- ing to the variance map for the zone where the vehicle will be driven. When properly set, the compass will automatically account for this difference.

266 UNDERSTANDING YOUR INSTRUMENT PANEL Setting the Compass Variance Refer to the variance map for the correct compass vari- ance zone. To check the variance zone, the ignition must be ON. Press and hold the left button (located on the instrument cluster) for approximately 10 seconds to enter the variance mode and release the button when the VAR symbol appears. The current variance value will also be displayed. To change the zone, press the left button once to increment the zone. The default is Zone 8. After Zone 15, the values will wrap around to Zone 1. When the correct zone is displayed (per the Compass Variance Zone Map) for the zone that the vehicle is located in, wait for about five seconds; then the trip computer will store the variance value in memory and the compass will resume normal operation. NOTE: The U.S./Metric display will change from En- glish to Metric or Metric to English before the VAR

symbol appears, however, it will revert back to its original setting after programming the compass func- tions.

Compass Variance Map

Outside Temperature If the outside temperature is more than 131°F (55°C), the display will show 131°F (55°C). When the outside tem- perature is less than ⫺40°F (⫺40°C), the display will show ⫺40°F (⫺40°C).

MEDIA CENTER 230 (REQ) — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK)

NOTE: The radio sales code is located on the lower right side of the radio faceplate.

UNDERSTANDING YOUR INSTRUMENT PANEL 267

Media Center 230 (REQ) Operating Instructions - Radio Mode

NOTE: The ignition switch must be in the ON or ACC position to operate the radio.

268 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360
degrees) in either direction without stopping. Turning the ON/VOLUME control knob to the right increases the volume and to the left decreases it. When the audio system is turned ON, the sound will be set at the same volume level as last played. SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it.

SCAN Button Pressing the SCAN button causes the tuner to search for the next listenable station in AM, FM or Satellite (if equipped) frequencies, pausing for five seconds at each listenable station before continuing to the next. To stop the search, press the SCAN button a second time. Voice Command Button Uconnect™ Phone — If Equipped Press this button to operate the Uconnect™ Phone feature (if equipped). Refer to “Uconnect™ Phone” in “Under- standing The Features Of Your Vehicle”. If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With Uconnect” message will display on the radio screen. Phone Button Uconnect™ Phone — If Equipped Press this button to operate the Uconnect™ Phone feature (if equipped). Refer to “Uconnect™ Phone” in “Under- standing The Features Of Your Vehicle”.

If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With Uconnect” message will display on the radio screen. TIME Button Press the TIME button to alternate locations of the time and frequency display. Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. the minutes using the right side TUNE/ 4. Adjust SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change.

UNDERSTANDING YOUR INSTRUMENT PANEL 269
5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button and selecting the “SET HOME CLOCK” entry. Once in this display follow the above procedure, starting at step 2. INFO Button Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text message broadcast from an FM station (FM mode only). RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in AM, FM or Satellite (if equipped) frequencies. TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency.

270 UNDERSTANDING YOUR INSTRUMENT PANEL Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display. Turn the TUNE/ SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers.

Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade. MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be se- lected. Many radio stations do not currently broadcast Music Type information. Toggle the MUSIC TYPE button to select the following format types:

Program Type

No program type or un-

defined

Adult Hits Classical

Classic Rock

College Country

Foreign Language

Information

Jazz News

Nostalgia

Oldies

Personality

Public

16-Digit Character Dis-

play

None

Adlt Hit Classicl Cls Rock College Country Language

Inform Jazz News

Nostalga Oldies Persnlty Public

UNDERSTANDING YOUR INSTRUMENT PANEL 271

Program Type

Rhythm and Blues Religious Music Religious Talk

Rock Soft

Soft Rock

Soft Rhythm and Blues

Sports Talk Top 40
Weather

16-Digit Character Dis-

play R & B

Rel Musc Rel Talk

Rock Soft

Soft Rck Soft R & B

Sports Talk Top 40
Weather

By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode.

272 UNDERSTANDING YOUR INSTRUMENT PANEL If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station. SETUP Button Pressing the SETUP button allows you to select between the following items: NOTE: Turn the TUNE/SCROLL control knob to scroll through the entries. Push the AUDIO/SELECT button to select an entry and make changes. • DVD Enter - When the disc is in DVD Menu mode, selecting DVD Enter will allow you to play the current highlighted selection. Use the remote control to scroll up and down the menu (if equipped). • DISC Play/Pause - You can toggle between playing the DVD and pausing the DVD by pushing the SELECT button (if equipped).

• DVD Play Options - Selecting the DVD Play Options will display the following: • Subtitle – Repeatedly pressing SELECT will switch subtitles to different subtitle languages that are available on the disc (if equipped). • Audio Stream – Repeatedly pressing SELECT will switch to different audio languages (if supported on the disc) (if equipped). • Angle – Repeatedly pressing SELECT will change the viewing angle if supported by the DVD disc (if equipped).

NOTE: • The available selections for each of the above entries • These selections can only be made while playing a

varies depending upon the disc.

DVD.

equipped).

OFF (if equipped).

• VES™ Power - Allows you to turn VES™ ON and • VES™ Lock - Locks out rear VES™ remote controls (if • VES™ CH1/CH2 - Allows the user to change the mode of either the IR1 or IR2 wireless headphones by pressing the AUDIO/SELECT button (if equipped). • Set Home Clock - Pressing the SELECT button allows you to set the clock. Turn the TUNE/SCROLL control knob to adjust the hours and then press and turn the TUNE/SCROLL control knob to adjust the minutes. Press the TUNE/SCROLL control knob again to save changes. • Player Defaults - Selecting this item will allow the user to scroll through the following items and set defaults according to customer preference.

UNDERSTANDING YOUR INSTRUMENT PANEL 273

Menu Language — If Equipped Selecting this item will allow the user to choose the default startup DVD menu language (effective only if language supported by disc). If you want to select a language not listed, then scroll down and select ⬙other.⬙ Enter the four-digit country code using the TUNE/ SCROLL control knob to scroll up and down to select the number and then push to select. Audio Language — If Equipped Selecting this item allows you to choose a default audio language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting ⬙other.⬙ Enter the country code using the TUNE/SCROLL control knob to scroll up and down to select the number and then push to select.

274 UNDERSTANDING YOUR INSTRUMENT PANEL Subtitle Language — If Equipped Selecting this item allows you to choose a default subtitle language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting ⬙other.⬙ Enter the country code using the TUNE/SCROLL control knob to scroll up and down to select the number and then push to select. Subtitles — If Equipped Selecting this item allows you to choose between subtitle Off or On. Audio DRC — If Equipped Selecting this item allows you to limit maximum audio dynamic range. The default is set to ⬙High,⬙ and under this setting, dialogues will play at 11 db higher than if the setting is ⬙Normal.⬙ Aspect Ratio — If Equipped Selecting this item allows you to choose between wide screen, pan scan, and letter box.

AutoPlay — If Equipped When this is set to On and a DVD video is inserted, it will bypass the DVD menu screen and automatically play the movie. In some rare cases, the DVD player may not auto-play the main title. In such cases, use the MENU button on the remote control to select desired title to play. NOTE: The user will have to set these defaults before loading a disc. If changes are made to these settings after a disc is loaded, changes will not be effective. Also, the defaults are effective only if the disc supports the customer-preferred settings. AM and FM Buttons Press the buttons to select AM or FM mode. SET Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this station

and press and release that button. If a button is not selected within five seconds after pressing the SET but- ton, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM, 12 FM, and 12 Satellite (if equipped) stations to be stored into pushbutton memory. The stations stored in SET 2
memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display.

UNDERSTANDING YOUR INSTRUMENT PANEL 275

Buttons 1 - 6
These buttons tune the radio to the stations that you commit to pushbutton memory {12 AM, 12 FM, and 12
Satellite (if equipped) stations}. DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes. Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play, DVD-VIDEO) The radio DVD player and many DVD discs are coded by geographic region. These region codes must match in order for the disc to play. If the region code for the DVD disc does not match the region code for the radio DVD player, it will not play the disc. Customers may take their vehicle to an authorized dealer to change the region code of the player a maximum of five times.

276 UNDERSTANDING YOUR INSTRUMENT PANEL

CAUTION!

The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate “Disc Hot” and shut off until a safe temperature is reached. This shutdown is necessary to protect the optics of the DVD player and other radio internal components.

NOTE: The ignition switch must be in the ON or ACC position to operate the radio. LOAD Button — Loading Compact Disc(s) Press the LOAD button and the pushbutton with the corresponding number (1-6) where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC. After the radio displays ⬙INSERT DISC,⬙ insert the CD into the player.

Radio display will show ⬙LOADING DISC⬙ when the disc is loading and “READING DISC” when the radio is reading the disc.

CAUTION!

This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism.

Eject Button — Ejecting Compact Disc(s)

Press the EJECT button and the pushbutton with the corresponding number (1-6) where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. Press and hold the EJECT button for five seconds and all CDs will be ejected from the radio.

The disc can be ejected with the radio and ignition OFF. SEEK Button (CD MODE) Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. Pressing and holding the SEEK button will allow you to scroll through the tracks faster in CD and MP3/MWA modes. SCAN Button (CD MODE) Press the SCAN button to scan through each track on the CD currently playing. TIME Button (CD MODE) Press this button to change the display from a large CD playing time display to a small CD playing time display.

UNDERSTANDING YOUR INSTRUMENT PANEL 277

RW/FF (CD MODE) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Rewind) button works in a similar manner. AM or FM Button (CD MODE) Switches the radio into the AM or FM radio mode. Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however, acceptable MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the following restrictions. Supported Media (Disc Types) The MP3/WMA file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3,WMA, DVD Video, DVD-R, DVD-RW, DVD+R, DVD+RW, and CDDA+MP3.

278 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660
Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor- mally. UDF and Apple HFS formats are not supported. The radio uses the following limits for file systems: • Maximum number of directory levels: 8
• Maximum number of files: 255
• Maximum number of folders: 100
• Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a three- • Level 2: 31 (including a separator ⬙.⬙ and a three-

character extension)

character extension)

Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3/ WMA files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3/ WMA playback may result in longer disc loading times. If a disc contains multi-formats, such as CD audio and MP3/WMA tracks, the radio will only play the MP3/ WMA tracks on that disc. Supported MP3/WMA File Formats The radio will recognize only files with the *.MP3/WMA extension as MP3/WMA files. Non-MP3/WMA files named with the *.MP3/WMA extension may cause play- back problems. The radio is designed to recognize the file as an invalid MP3/WMA and will not play the file.

When using the MP3/WMA encoder to compress audio data to an MP3/WMA file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3/WMA files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates.

MPEG Specifi-

cation

Sampling Fre- quency (kHz)

MPEG-1 Audio

Layer 3

48, 44.1, 32

MPEG-2 Audio

Layer 3

24, 22.05, 16

WMA Specifica-

tion

Sampling Fre- quency (kHz)

WMA

44.1 and 48

Bit Rate (kbps)

320, 256, 224, 192, 160, 128, 112, 96, 80, 64,

56, 48

160, 128, 144, 112, 96, 80, 64,

56, 48

Bit Rate (kbps)

48, 64, 96, 128, 160, 192 VBR

UNDERSTANDING YOUR INSTRUMENT PANEL 279
ID3 Tag information for artist, song title, and album title are supported for ID3 version 1 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3/WMA files. Loading times for playback of MP3/WMA files may be affected by the following: • Media - CD-RW media may take longer to load than • Medium formats - Multisession discs may take longer

CD-R media

to load than non-multisession discs

280 UNDERSTANDING YOUR INSTRUMENT PANEL

• Number of files and folders - Loading times will

increase with more files and folders

To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a single-session disc, enable the “Disc at Once” option before writing to the disc. LIST Button (DISC Mode for MP3/WMA Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob. Selecting a folder by pressing the TUNE/SCROLL control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files). The folder list will time out after five seconds.

INFO Button (DISC Mode for MP3/WMA Play) Pressing the INFO button repeatedly will scroll through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). Press the INFO button once more to return to ⬙elapsed time⬙ priority mode. Press and hold the INFO button for three seconds or more and radio will display song titles for each file. Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3/WMA player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.

Pressing the AUX button will change the mode to auxil- iary device if the AUX jack is connected. NOTE: The AUX device must be turned on and the device’s volume set to the proper level. If the AUX audio is not loud enough, turn the device’s volume up. If the AUX audio sounds distorted, turn the device’s volume down. SEEK Button (Auxiliary Mode) No function. SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode)

No function.

UNDERSTANDING YOUR INSTRUMENT PANEL 281

TIME Button (Auxiliary Mode) Press the TIME button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. RW/FF (Auxiliary Mode) No function. SET Button (Auxiliary Mode) No function. Operating Instructions — Voice Command System (If Equipped) For the radio, refer to “Voice Command” in “Understand- ing The Features Of Your Vehicle”. For Uconnect™ “Voice Command,” refer to “Uconnect™ Phone” in “Understanding The Features Of Your Vehicle”.

282 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Uconnect™ Phone (If Equipped) Refer to “Uconnect™ Phone” in “Understanding The Features Of Your Vehicle”. Operating Instructions - Uconnect™ Multimedia (Satellite Radio) (If Equipped) Refer to “Uconnect™ Multimedia (Satellite Radio)”. Operating Instructions - Video Entertainment System (VES)™ (If Equipped) Refer to separate “Video Entertainment System (VES)™ Guide.” Dolby威 Manufactured under license from Dolby威 Laboratories. ⬙Dolby威⬙ and the double-D symbol are trademarks of Dolby威 Laboratories.

Macrovision This product incorporates copyright protection technol- ogy that is protected by U.S. patents and other intellec- tual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. DTS™ ⬙DTS™⬙ and ⬙DTS™ 2.0⬙ are trademarks of Digital The- ater Systems, Inc.

MEDIA CENTER 730N/430 (RER/REN/RBZ) — AM/FM STEREO RADIO AND CD/DVD/HDD/NAV — IF EQUIPPED

NOTE: The sales code is located on the lower right side of the unit’s faceplate.

The REN, RER and RBZ radios contain a CD/DVD player, USB port, and a 30-gigabyte hard drive (HDD). Sirius Satellite Radio is optional. The 6.5 in (16.5 cm) touch screen allows for easy menu selection. The RER radio also contains a Global Positioning System (GPS)-based Navigation system. Refer to your Uconnect™ Multimedia REN, RER or RBZ user’s manual for detailed operating instructions. Operating Instructions — Voice Command System — If Equipped Refer to “Voice Command” in the Uconnect™ User Manual located on the DVD for further details. Operating Instructions — Uconnect™ Phone — If Equipped Refer to “Uconnect™ Phone” in the Uconnect™ User Manual located on the DVD for further details.

UNDERSTANDING YOUR INSTRUMENT PANEL 283

Clock Setting Procedure — RBZ Radio

To Manually Set the Clock 1. Turn on the radio. 2. Touch the screen where the time is displayed, the clock setting menu will appear on the screen. 3. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is dis- played. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing down- ward is displayed. 4. To move the minute forward, touch the screen where the word “Min” with the arrow pointing upward is displayed. To move the minute backward, touch the screen where the word “Min” with the arrow pointing downward is displayed.

284 UNDERSTANDING YOUR INSTRUMENT PANEL 5. To save the new time setting, touch the screen where the word “Save” is displayed. Changing Daylight Savings Time When selected, this feature will display the time of day in daylight savings time. Proceed as follows to change the current setting: 1. Turn on the radio. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.” Touch the screen where the words “Daylight Savings” are dis- played to change the current setting. Show Time if Radio is Off When selected, this feature will display the time of day on the touch screen when the radio is turned off. Proceed as follows to change the current setting:

1. Turn on the radio. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Show Time if Radio is Off.” Touch the screen where the words “Show Time if Radio is Off” are displayed to change the current setting. Changing the Time Zone 1. Turn on the radio. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen. 4. Select a time zone by touching the screen where your selection appears. If you do not see a time zone that you

want to select, touch the screen where the word “Page” is displayed to view additional time zones in the menu. 5. Touch the screen where the word “Save” is displayed. Clock Setting Procedure — RER/REN Radio Uconnect威 gps — RER Only The GPS receiver used in this system is synchronized to the time data being transmitted by the GPS satellite. The satellite clock is Greenwich Mean Time (GMT). This is the worldwide standard for time. This makes the system’s clock very accurate once the appropriate time zone and daylight savings information is set. To Manually Set the Clock — RER/REN 1. Turn on the radio. 2. Touch the screen where the time is displayed. 3. Touch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen.

UNDERSTANDING YOUR INSTRUMENT PANEL 285
4. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is dis- played. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing down- ward is displayed. 5. To move the minute forward, touch the screen where the word “Min” with the arrow pointing upward is displayed. To move the minute backward, touch the screen where the word “Min” with the arrow pointing downward is displayed. 6. To save the new time setting, touch the screen where the word “Save” is displayed. Changing Daylight Savings Time When selected, this feature will display the time of day in daylight savings time. Proceed as follows to change the current setting: 1. Turn on the radio.

286 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Touch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.” Touch the screen where the words “Daylight Savings” are dis- played to change the current setting. Show Time if Radio is Off When selected, this feature will display the time of day on the touch screen when the radio is turned off. Proceed as follows to change the current setting: 1. Turn on the radio. 2. Touch the screen where the time is displayed. 3. Touch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen. 4. When this feature is on, a check mark will appear in the box next to the words “Show Time if Radio is Off.”

Touch the screen where the words “Show Time if Radio is Off” are displayed to change the current setting. Changing the Time Zone 1. Turn on the radio. 2. Touch the screen where the time is displayed. 3. Touch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen. 4. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen. 5. Select a time zone by touching the screen where your selection appears. If you do not see a time zone that you want to select, touch the screen where the word “Page” is displayed to view additional time zones in the menu. 6. Touch the screen where the word “Save” is displayed.

MEDIA CENTER 130 (RES) — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK)

NOTE: The radio sales code is located on the lower right side of the radio faceplate.

Media Center 130 (RES)

UNDERSTANDING YOUR INSTRUMENT PANEL 287

Operating Instructions — Radio Mode

NOTE: The ignition switch must be in the ON/RUN or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360
degrees) in either direction, without stopping. Turning the ON/VOLUME control knob to the right increases the volume, and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played.

288 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. TIME Button Press the TIME button to alternate display of the time and radio frequency. Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink.

4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save time change. 5. To exit, press any button/knob, or wait five seconds. RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM or FM frequencies. TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency. Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones.

Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display. Turn the TUNE/ SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers. Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers.

UNDERSTANDING YOUR INSTRUMENT PANEL 289
Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade. AM/FM Button Press the buttons to select either AM or FM mode. SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window. Select the button (1 to 6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET/RND button, the station will continue to play but will not be stored into pushbutton memory.

290 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6