2010 Jeep Wrangler Owners Manual

call. Press the button until you hear a call, press and hold the single beep, the incoming call was rejected. Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your button to place the current cellular phone. Press the call on hold and answer the incoming call. NOTE: The Uconnect™ Phone compatible phones in the market today do not support rejecting an incoming call

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99
when another call is in progress. Therefore, the user can only answer an incoming call or ignore it. Making a Second Call While Current Call is in Progress To make a second call while you are currently on a call, button and say ⬙Dial⬙ or ⬙Call⬙ followed press the by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to ⬙Toggling Between Calls⬙ in this section. To combine two calls, refer to ⬙Conference Call⬙ in this section. Place/Retrieve a Call From Hold To put a call on hold, press the button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the button until you hear a single beep.

100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Toggling Between Calls If two calls are in progress (one active and one on hold), button until you hear a single beep, press the indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at a time. Conference Call When two calls are in progress (one active and one on button until you hear a hold), press and hold the double beep indicating that the two calls have been joined into one conference call. Three-Way Calling button To initiate three-way calling, press the while a call is in progress, and make a second phone call, as described under ⬙Making a Second Call While Current Call is in Progress.⬙ After the second call has established, button until you hear a double press and hold the beep, indicating that the two calls have been joined into one conference call.

Call Termination To end a call in progress, momentarily press the button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the

button until you hear a single beep.

button to begin.

Redial • Press the • After the ⬙Ready⬙ prompt and the following beep, say • The Uconnect™ Phone will call the last number that

⬙Redial.⬙

was dialed from your cellular phone.

NOTE: This may not be the last number dialed from the Uconnect™ Phone.

Call Continuation Call continuation is the progression of a phone call on the Uconnect™ Phone after the vehicle ignition key has been switched to OFF. Call continuation functionality avail- able on the vehicle can be any one of three types: • After the ignition key is switched to OFF, a call can continue on the Uconnect™ Phone either until the call ends, or until the vehicle battery condition dictates cessation of the call on the Uconnect™ Phone and transfer of the call to the cellular phone. • After the ignition key is switched to OFF, a call can continue on the Uconnect™ Phone for a certain dura- tion, after which the call is automatically transferred from the Uconnect™ Phone to the cellular phone.

• An active call

is automatically transferred to the cellular phone after the ignition key is switched to OFF.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101

Uconnect™ Phone Features

Language Selection To change the language that the Uconnect™ Phone is using: • Press the • After the ⬙Ready⬙ prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais. • Continue to follow the system prompts to complete

button to begin.

the language selection.

After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every Uconnect™ Phone language change operation, only the language-specific 32-name phone- book is usable. The paired phone name is not language- specific and usable across all languages.

102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Emergency Assistance If you are in an emergency and the cellular phone is reachable: • Pick up the phone and manually dial the emergency

number for your area.

button to begin.

If the phone is not reachable and the Uconnect™ Phone is operational, you may reach the emergency number as follows: • Press the • After the ⬙Ready⬙ prompt and the following beep, say ⬙Emergency⬙ and the Uconnect™ Phone will instruct the paired cellular phone to call the emergency num- ber. This feature is supported in the U.S., Canada, and Mexico.

NOTE: • The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and

Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area. • If supported, this number may be programmable on button and • The Uconnect™ Phone does slightly lower your chances of successfully making a phone call as to that for the cellular phone directly.

some systems. To do this, press the say ‘Setup’, followed by ‘Emergency’.

WARNING!

To use your Uconnect™ Phone System in an emer- gency, your cellular phone must be: • turned on, • paired to the Uconnect™ System, • and have network coverage.

Towing Assistance If you need towing assistance: • Press the • After the ⬙Ready⬙ prompt and the following beep, say

button to begin.

⬙Towing Assistance.⬙

NOTE: • The towing assistance number dialed is based on the country where the vehicle is purchased (1-800-528- 2069 for the U.S., 1-877-213-4525 for Canada, 55-14- 3454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico). Please refer to the 24-Hour Towing Assistance coverage details on the DVD in the Warranty Information Booklet and the 24-Hour Tow- ing Assistance references. • If supported, this number may be programmable on button and

some systems. To do this, press the say “Setup”, followed by “Towing Assistance”.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103

Paging To learn how to page, refer to ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the Uconnect™ Phone. Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.⬙ Working with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system. You can use your Uconnect™ Phone to access a voice mail system or an automated service, such as a paging service or automated customer service line. Some ser- vices require immediate response selection. In some instances, the Uconnect™ Phone.

that may be too quick for use of

104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your Uconnect™ Phone that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can press the button and say the sequence you wish to enter, followed by the word ⬙Send.⬙ For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you can button and say, ⬙3 7 4 6 #Send.⬙ Saying press the a number, or sequence of numbers, followed by ⬙Send,⬙ is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can also send stored Uconnect™ Phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you wish to button and say, “Send.” The call and then press the system will prompt you to enter the name or number and say the name of the phonebook entry you wish to send.

The Uconnect™ Phone will then send the corresponding phone number associated with the phonebook entry, as tones over the phone. NOTE: • You may not hear all of the tones due to cellular phone • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature.

network configurations. This is normal.

Barge In - Overriding Prompts The “Voice Command” button can be used when you wish to skip part of a prompt and issue your voice command immediately. For example, if a prompt is asking ⬙Would you like to pair a phone, clear a...,⬙ you button and say, ⬙Pair a Phone⬙ to could press the select that option without having to listen to the rest of the voice prompt.

button to begin.

Turning Confirmation Prompts ON/OFF Turning confirmation prompts off will stop the system from confirming your choices (e.g., the Uconnect™ Phone will not repeat a phone number before you dial it). • Press the • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Confirmations.⬙ The Uconnect™ Phone will play the current confirmation prompt status and you will be given the choice to change it. Phone and Network Status Indicators If available on the radio and/or on a premium display such as the instrument panel cluster, and supported by your cellular phone, the Uconnect™ Phone will provide notification to inform you of your phone and network status when you are attempting to make a phone call using Uconnect™ Phone. The status is given for roaming, network signal strength, phone battery strength, etc.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105

Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the Uconnect™ Phone (while dialing via the cellular phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth威 cellular phone, the audio will be played through your vehicle’s audio system. The Uconnect™ Phone will work the same as if you dial the number using Voice Command. NOTE: Certain brands of cellular phones do not send the dial ring to the Uconnect™ Phone to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number the user may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio.

106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mute/Un-Mute (Mute OFF) When you mute the Uconnect™ Phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the Uconnect™ Phone: • Press the • Following the beep, say ⬙Mute.⬙ In order to un-mute the Uconnect™ Phone: • Press the • Following the beep, say ⬙Mute off.⬙ Advanced Phone Connectivity

button.

button.

Transfer Call to and from Cellular Phone The Uconnect™ Phone allows ongoing calls to be trans- ferred from your cellular phone to the Uconnect™ Phone without terminating the call. To transfer an ongoing call

from your Uconnect™ Phone paired cellular phone to the Uconnect™ Phone or vice versa, press the button and say ⬙Transfer Call.⬙ Connect or Disconnect Link Between the Uconnect™ Phone and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively ⬙connected⬙ with one electronic device at a time. If you would like to connect or disconnect the Bluetooth威 connection between a Uconnect™ Phone paired cellular phone and the Uconnect™ Phone, follow the instructions described in your cellular phone User’s Manual. List Paired Cellular Phone Names • Press the • After the “Ready” prompt and the following beep, say

button to begin.

“Setup Phone Pairing.”

• When prompted, say ⬙List Phones.⬙ • The Uconnect™ Phone will play the phone names of all paired cellular phones in order from the highest to the lowest priority. To “select” or “delete” a paired button and phone being announced, press the say “Select” or “Delete.” Also, see the next two sec- tions for an alternate way to “select” or “delete” a paired phone.

button to begin.

Select Another Cellular Phone This feature allows you to select and start using another phone paired with the Uconnect™ Phone. • Press the • After the ⬙Ready⬙ prompt and the following beep, say • You can also press the

button at any time while the list is being played, and then choose the phone that you wish to select.

⬙Setup Select Phone⬙ and follow the prompts.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107

• The selected phone will be used for the next phone call. the Uconnect™ Phone will return to using the highest priority phone present in or near (approximately within 30 ft (9 m)) the vehicle.

the selected phone is not available,

If

button to begin.

⬙Setup Phone Pairing.⬙

Delete Uconnect™ Phone Paired Cellular Phones • Press the • After the ⬙Ready⬙ prompt and the following beep, say • At the next prompt, say ⬙Delete⬙ and follow the • You can also press the

button at any time while the list is being played, and then choose the phone you wish to delete.

prompts.

108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your Uconnect™ Phone

Uconnect™ Phone Tutorial To hear a brief tutorial of the system features, press the

button and say “Uconnect™ Tutorial.”

Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers, the Uconnect™ Phone Voice Training feature may be used. To enter this training mode, follow one of the two following proce- dures: From outside the Uconnect™ Phone mode (e.g., from radio mode): • Press and hold the • Press the

button and say the ⬙Setup, Voice

button for five seconds until

the session begins, or,

Training⬙ command.

You can either press the Uconnect™ Phone button to restore the factory setting or repeat the words and phrases when prompted by the Uconnect™ Phone. For best results, the Voice Training session should be com- pleted when the vehicle is parked with the engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only. Reset • press the • After the “Ready” prompt, and the following beep, say

button.

“Uconnect™ Setup”, then “Reset”.

This will delete all phone pairing, phone book entries, and other settings in all language modes. The System will prompt you before resetting to factory settings.

Voice Command • For best performance, adjust the rearview mirror to provide at least 1⁄2 in (1 cm) gap between the overhead console (if equipped) and the mirror.

• Always wait for the beep before speaking. • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. • Make sure that no one other than you is speaking during a Voice Command period. • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface,

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109

• fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work for some. • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say ⬙Send.⬙ • Storing names in the phonebook when the vehicle is • It is not recommended to store similar sounding • Phonebook (Downloaded and Uconnect™ Phone Lo- cal) name recognition rate is optimized when the entries are not similar.

names in the Uconnect™ Phonebook.

not in motion is recommended.

110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

be spoken “eight-zero-zero” not “eight hundred”.

• Numbers must be spoken in single digits. “800” must • You can say ⬙O⬙ (letter ⬙O⬙) for ⬙0⬙ (zero). • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. • In a convertible vehicle, system performance may be

compromised with the convertible top down.

Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface,

• fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the Uconnect™ Phone. • Echo at the phone far end can sometimes be reduced • In a convertible vehicle, system performance may be

by lowering the in-vehicle audio volume.

compromised with the convertible top down.

Recent Calls If your phone supports “Automatic Phonebook Down- load”, Uconnect™ Phone can list your Outgoing, Incom- ing and Missed Calls.

SMS Uconnect™ Phone can read or send new messages on your phone. Read Messages: If you receive a new text message while your phone is connected to Uconnect™ Phone, an announcement will be made to notify you that you have a new text message. If you wish to hear the new message: • Press the • After the “Ready” prompt and the following beep, say • Uconnect™ Phone will play the new text message for

“SMS Read” or “Read Messages.”

button.

you.

After reading a message, you can “Reply” or “Forward” the message using Uconnect™ Phone.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111

Send Messages: You can send messages using Uconnect™ Phone. To send a new message: • Press the • After the “Ready” prompt and the following beep, say • You can either say the message you wish to send or say

“SMS Send” or “Send Messages.”

button.

“List Messages.” There are 20 preset messages.

To send a message, press the system is listing the message and say “Send.” Uconnect™ Phone will prompt you to say the name or number of the person you wish to send the message to.

button while the

112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE List of Preset Messages: 1. Yes 2. No 3. Where are you? 4. I need more direction. 5. L O L 6. Why 7. I love you 8. Call me 9. Call me later 10. Thanks

11. See You in 15 minutes 12. I am on my way 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now 18. When can we meet 19. Send number to call 20. Start without me

Turn SMS Incoming Announcement ON/OFF Turning the SMS Incoming Announcement OFF will stop the system from announcing the new incoming mes- sages. • Press the • After the “Ready” prompt and the following beep, say “Setup, Incoming Message Announcement,” you will then be given a choice to change it.

button.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113

Bluetooth威 Communication Link Cellular phones have been found to lose connection to the Uconnect™ Phone. When this happens, the connec- tion can generally be reestablished by switching the phone off/on. Your cellular phone is recommended to remain in Bluetooth威 ON mode. Power-Up After switching the ignition key from OFF to either the ON or ACC position, or after a language change, you must wait at least five seconds prior to using the system.

114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115

116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Voice Commands

Alternate(s)

Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117

Voice Commands

Alternate(s)

Primary call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home

118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Voice Commands

Alternate(s)

pairing phone book

Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again

Voice Commands

Alternate(s)

return or main menu select

phone settings or phone set up

Primary redial return to main menu select phone send set up

towing assistance transfer call Uconnect™ Tutorial try again voice training work yes

General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.

VOICE COMMAND — IF EQUIPPED

Voice Command System Operation

This Voice Command system allows you to control your AM, FM radio, satellite radio, disc player, and a memo recorder.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119
NOTE: Take care to speak into the Voice Interface System as calmly and normally as possible. The ability of the Voice Interface System to recognize user voice com- mands may be negatively affected by rapid speaking or a raised voice level.

WARNING!

Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in an accident causing serious injury or death.

button, you When you press the Voice Command will hear a beep. The beep is your signal to give a command.

120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you do not say a command within a few NOTE: seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists button, listen options, press the Voice Command for the beep, and say your command. button while the Pressing the Voice Command system is speaking is known as “barging in.” The system will be interrupted, and after the beep, you can add or change commands. This will become helpful once you start to learn the options. NOTE: At any time, you can say the words “Cancel”, “Help” or “Main Menu”. These commands are universal and can be used from any menu. All other commands can be used depending upon the active application.

For example, if you are in the disc menu and you are listening to FM radio, you can speak commands from the disc menu or from the FM radio menu. When using this system, you should speak clearly and at a normal speaking volume. The system will best recognize your speech if the win- dows are closed, and the heater/air conditioning fan is set to low. At any point, if the system does not recognize one of your commands, you will be prompted to repeat it. To hear the first available Menu, press the Voice button and say “Help” or “Main Command Menu”.

Commands The Voice Command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the Volume 1. Start a dialogue by pressing the Voice Command

button.

2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Command system is speaking. Please note the volume setting for Voice Command is different than the audio system. Main Menu Start a dialogue by pressing the Voice Command button. You may say “Main Menu” to switch to the main menu.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121

In this mode, you can say the following commands: • “Radio” (to switch to the radio mode) • “Disc” (to switch to the disc mode) • “Memo” (to switch to the memo recorder) • “System Setup” (to switch to system setup) Radio AM (or Radio Long Wave or Radio Medium Wave — If Equipped) To switch to the AM band, say “AM” or “Radio AM”. In this mode, you may say the following commands: • “Frequency” (to change the frequency) • “Next Station” (to select the next station) • “Previous Station” (to select the previous station) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to switch to the main menu)

122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Radio FM To switch to the FM band, say “FM” or “Radio FM”. In this mode, you may say the following commands: • “Frequency” (to change the frequency) • “Next Station” (to select the next station) • “Previous Station” (to select the previous station) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Satellite Radio To switch to satellite radio mode, say “Sat” or “Satellite Radio”. In this mode, you may say the following com- mands: • “Channel Number” (to change the channel by its • “Next Channel” (to select the next channel)

spoken number)

• “Previous Channel” (to select the previous channel) • “List Channel” (to hear a list of available channels) • “Select Name” (to say the name of a channel) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Disc To switch to the disc mode, say “Disc”. In this mode, you may say the following commands: • “Track” (#) (to change the track) • “Next Track” (to play the next track) • “Previous Track” (to play the previous track) • “Main Menu” (to switch to the main menu)

Memo To switch to the voice recorder mode, say “Memo”. In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the

recording, you may press the Voice Command button to stop recording. You proceed by saying one of the following commands: − “Save” (to save the memo) − “Continue” (to continue recording) − “Delete” (to delete the recording) • “Play Memos” (to play previously recorded memos) — During the playback you may press the Voice button to stop playing memos. You Command proceed by saying one of the following commands: − “Repeat” (to repeat a memo) − “Next” (to play the next memo)

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123
− “Previous” (to play the previous memo) − “Delete” (to delete a memo) • “Delete All” (to delete all memos) System Setup To switch to system setup, say “Setup”. In this mode, you may say the following commands: • “Language German” • “Language Dutch” • “Language Italian” • “Language English” • “Language French” • “Language Spanish” • “Tutorial” • “Voice Training”

124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Keep in mind that you have to press the Voice button first and wait for the beep Command before speaking the “Barge In” commands. Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers the Uconnect™ Voice “Voice Training” feature may be used. button, say “System 1. Press the Voice Command Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition. 2. Repeat the words and phrases when prompted by Uconnect™ Voice. For best results, the “Voice Training” session should be completed when the vehicle is parked, engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only.

SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. They need to be used properly for safe operation of the vehicle.

WARNING!

• DO NOT allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and

using a seat belt properly.

Front Seat Adjustment Move the seat forward or rearward by lifting the lever. Release the lever when the seat is in the desired position. Using body pressure, move forward and rearward on the seat to make sure that the latch is fully engaged.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125

WARNING!

Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Only adjust a seat while the vehicle is parked.

Manual Seat Adjustment

126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seat Height Adjustment — If Equipped The driver’s seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat. Pull upward on the handle to raise the seat; push downward on the handle to lower the seat.

Front Seatback Recline Lean forward before lifting the handle, then lean back to the desired position and release the handle. Lift the handle to return the seatback to an upright position.

Seat Height Adjustment

Recline Lever

WARNING!

Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seatbelt and be seriously or fatally injured. Use the recliner only when the vehicle is parked.

Front Easy Entry Seats — Two Door Models Push the lever on the seatback rearward (toward the rear of the vehicle) to tilt the entire seat forward.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127

Easy Entry Combination Lever

128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Easy Entry Seat With Combination Lever

1. To return the seat to a sitting position, rotate the seatback upright until it locks. 2. Push the seat rearward until the track locks.

NOTE: • If equipped with combination lever the seatback will return to its first locked position. The recliner handle will have to be actuated to adjust the seatback to the desired reclined position. • The front passenger seats have a track memory, which returns the seat to just past the halfway point of the track regardless of its original position. • The recliner and easy entry levers should not be used during the automatic returning of the seat to its sitting position.

Head Restraints Head restraints can reduce the risk of injury in the event of a rear impact. The head restraint should be adjusted so the top of the head restraint is located above the top of your ear.

To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the large button, located on the base of the head restraint, and push downward on the head restraint.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129

NOTE: The rear head restraints are not adjustable. To remove the head restraint, pull upward on the head restraint to it’s highest position, push in both buttons at the base of each head restraint rod, and simultaneously pull up on the head restraint.

Adjustable Head Restraints

Removing Head Restraint

130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To install the head restraint, insert the head restraint rods into each guide, apply pressure down on the headrest until the head restraint reaches the first lock position, push the large button in and push down and adjust head restraint to desired position. NOTE: Ensure that the front of the head restraint is facing toward the front of the vehicle.

WARNING!

Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to operating the vehicle and never adjusted while the vehicle is in motion. Always adjust the head restraints when the vehicle is in PARK.

Fold and Tumble Rear Seat — Two Door Models NOTE: • Prior to folding the rear seat, it may be necessary to • Be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily.

reposition the front seats.

1. Lift the seatback release lever and fold the seatback forward.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131

Rear Seat Release 2. Slowly flip the entire seat forward.

Folding Rear Seat

3. Return the seat to the normal position. 4. Raise the rear seatback using the assist strap and firmly lock the seat into position.

132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Removing the Rear Seat — Two Door Models

WARNING!

• It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and • In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure that the seats are fully latched.

using a seat belt properly.

1. Remove the three rear subwoofer mounting nuts using a 15 mm socket.

(if equipped)

Subwoofer

2. Unplug the electrical connector from the rear sub- woofer (if equipped).

3. Fold the rear seat forward following steps 1 through 3
under “Fold and Tumble Rear Seat” in this section. 4. Press down on the release bar on each side, and pull the seat out and away from the lower bracket. 5. Remove the seat from the vehicle.

Release Bar Location

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133

Replacing the Rear Seat — Two Door Models Reverse the steps for removing the seat.

WARNING!

• To help protect against personal injury, passengers should not be seated in the rear cargo area with the rear seat folded down or removed from the ve- hicle. • The rear cargo space is intended for load carrying purposes only, not for passengers who should sit in seats and use seat belts.

60/40 Split Folding Rear Seat — Four Door Models To provide additional storage area, each rear seat can be folded flat to allow for extended cargo space and still maintain some rear seating room.

reposition the front seat to its mid-track position.

134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Prior to folding the rear seat, it may be necessary to • Be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily.

WARNING!

• It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and

using a seat belt properly.

To Fold Down the Rear Seat Locate the pull strap (lower outboard side of seat), and pull it toward you until the seatback releases.

Pull Strap

To Raise the Rear Seat Raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. If the rear seatback is not fully latched, the NOTE: center shoulder belt will not be able to be extended for use. If you cannot extend the center shoulder belt, make sure your seatback is fully latched.

WARNING!

Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135

TO OPEN AND CLOSE THE HOOD Release both the hood latches.

Hood Latch

Raise the hood and locate the safety latch, located in the middle of the hood opening. Push the latch to the left side of the vehicle, to open the hood. You may have to push down slightly on the hood before pushing the safety latch. Insert the support rod into the slot on the hood.

136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To close the hood, remove the support rod from the hood panel and place it in the retaining clip. Lower the hood slowly. Secure both of the hood latches.

WARNING!

Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death.

LIGHTS

Multifunction Lever The multifunction lever controls the operation of the parking lights, headlights, headlight beam selection, passing light, fog lights, instrument panel light dimming and turn signals. The lever is located on the left side of the steering column.

Multifunction Lever

Headlights and Parking Lights Turn the end of the multifunction lever to the first detent for parking lights and instrument panel lights. Turn to the second detent for headlight operation.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137

Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.

Headlight Switch

NOTE: Lens fogging can occur under certain weather conditions. Turning the headlights on will usually accel- erate the clearing process.

Turn Signal Operation

138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. • A tone will chime if the turn signals are left on for

more than 1 mile (2 km).

Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Lights-On Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound when the driver’s door is opened.

High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headlights back to low beam. Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward the steer- ing wheel. This will turn on the high beam headlights until the lever is released. Front Fog Lights — If Equipped

The front fog light switch is located on the multi- function lever. To activate the front fog lights, turn on the parking or low beam headlights and pull

out the end of the lever. NOTE: The fog lights will only operate with the parking lights or the headlights on low beam. Selecting high beam headlights will turn off the fog lights.

Instrument Panel Dimmer Rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the park- ing lights or headlights are on. Rotate the center portion of the lever upward to the next detent position to brighten the odometer and radio when the parking lights or headlights are on. Rotate the center portion of the lever upward to the last detent to turn on the interior lighting.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139

Dimmer Control

Daytime Running Lights — If Equipped The headlights come on at a low intensity level after the vehicle has been driven approximately 3 ft (1 m). They will turn off when the vehicle is turned off or when the headlights are switched on.

The rearmost cargo lamp (available on four-door models) may be turned on by pressing either of the switches, located on either side of the lens. Press a switch a second time to turn the light off. Also, the rear cargo lamp may be turned on by pressing the lens. Press the lens a second time to turn the light off.

140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights The overhead light will turn on when a door is opened. It may also be turned on by rotating the control for the dimmer switch on the multifunction lever fully upward. The overhead light will automatically turn off in approxi- mately 10 minutes if a door is left open or the dimmer control is left in the dome light position. Turn the ignition switch ON to restore the overhead light operation. Cargo Lamp The courtesy and dome lights will turn on when the front doors are opened, by rotating the control for the dimmer switch on the multifunction lever fully upward, or if equipped, when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter.

Cargo Lamp

When a door is open and the interior lights are on, rotating the dimmer control to the extreme bottom posi- tion will cause all the interior lights to turn off. This is also known as the ⬙Party⬙ mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery.

WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located at the end of the lever. For information on using the rear window wiper/ washer, refer to “Rear Window Features” in “Under- standing the Features of Your Vehicle”.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141

Windshield Wiper/Washer Lever

142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper opera- tion.

Front Wiper Control

CAUTION!

In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.

Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Rotate the end of the lever to the first detent position for one of five intermittent settings. The delay cycle can be set anywhere between 2 to 30 seconds.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143

Front Wiper Control

Windshield Washers To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for two or three wipe cycles after the lever is released, and then resume the intermittent interval previously selected.

144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the lever is pulled while in the off position, the wipers will operate for two or three wipe cycles and then turn off.

WARNING!

Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.

Mist Feature Push down on the wiper lever to activate a single wipe to clear off road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate.

Mist Control

NOTE: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid.

TILT STEERING COLUMN This feature allows you to tilt the steering column upward or downward. The tilt lever is located on the steering column, below the turn signal lever. Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Pull upwards on the lever to lock the column firmly in place.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145

Tilt Steering Column

146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this warning may result in serious injury or death.

ELECTRONIC SPEED CONTROL — IF EQUIPPED Electronic Speed Control takes over the accelerator op- eration at speeds greater than 25 mph (40 km/h). The Electronic Speed Control lever is located on the right side of the steering wheel.

Electronic Speed Control Lever

In order to ensure proper operation, the Elec- NOTE: tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control

System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button. The Cruise Indicator Light in the instrument cluster will illuminate. To turn the Elec- tronic Speed Control system off, push the ON/OFF button a second time. The cruise indicator light will turn off. The Electronic Speed Control system should be turned off when not in use.

WARNING!

Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the Electronic Speed Control system off when you are not using it.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147

To Set a Desired Speed Turn the Electronic Speed Control ON. When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed. NOTE: The vehicle should be traveling at a steady speed and on level ground before pressing the SET lever. To Deactivate A soft tap on the brake pedal, pulling the Electronic Speed Control lever toward you, or normal brake or clutch pressure while slowing the vehicle will deactivate Electronic Speed Control without erasing the set speed memory. Pressing the ON/OFF button or turning the ignition switch OFF erases the set speed memory. To Resume Speed To resume a previously set speed, push the RESUME ACCEL lever up and release. Resume can be used at any speed above 25 mph (40 km/h).

148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary the Speed Setting When the Electronic Speed Control is set, you can in- crease speed by pushing up and holding the RESUME ACCEL lever. If the lever is continually held in the RESUME ACCEL position, the set speed will continue to increase until the lever is released, then the new set speed will be established. Tapping RESUME ACCEL once will result in a 1 mph (1.6 km/h) speed increase. Each time the Electronic Speed Control lever is tapped, speed increases so that tapping the Electronic Speed Control lever three times will increase speed by 3 mph (4.8 km/h), etc. To decrease speed while the Electronic Speed Control is set, push down and hold the SET DECEL lever. If the lever is continually held in the SET DECEL position, the set speed will continue to decrease until the lever is released. Release the lever when the desired speed is reached, and the new set speed will be established.

Tapping the SET DECEL lever once will result in a 1 mph (1.6 km/h) speed decrease. Each time the lever is tapped, speed decreases. Manual Transmission Pressing the clutch pedal will disengage the Electronic Speed Control. A slight increase in engine RPM before the Electronic Speed Control disengages is normal. Vehicles equipped with manual transmissions may need to be shifted into a lower gear to climb hills without speed loss.

WARNING!

Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.

To Accelerate for Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149
On steep hills, a greater speed loss or gain and/or more frequent downshifts (auto transmission only) may occur so it may be preferable to drive without Electronic Speed Control.

WARNING!

Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.

150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLET There are two 12 Volt (13 Amp) auxiliary power outlets that can provide power for accessories designed for use with the standard power outlet adapters. The power outlet, located in the lower portion of the instrument panel, has a snap-on plastic cap so that it can be covered when not in use. When the optional cigar lighter heating element is used in the left-side power outlet, it heats when pushed in and pops out automatically when ready for use. To preserve the heating element, do not hold the lighter in the heating position. NOTE: Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced.

Power Outlets

The left-side power outlet is powered when the key is in the ON or ACC positions.

The right-side power outlet is powered directly from the battery (power available at all times). Items plugged into this power outlet may discharge the battery and/or prevent the engine from starting.

WARNING!

To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving • If this outlet is mishandled, it may cause an

the vehicle.

electric shock and failure.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151

CAUTION!

• Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high-power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery.

(Continued)

152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION! (Continued)

• Power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug.

CUPHOLDERS

Front Cupholders The front cupholders are located in the center console.

Front Cupholders

NOTE: The front cupholder insert is removable for cleaning.

Rear Cupholders The rear cupholders are located on the back of the center console.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153

STORAGE

Console Storage Compartment To lock or unlock the storage compartment, insert the ignition key and turn. To open the storage compartment, press the latch and lift the cover.

Rear Cupholders

Center Console

154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Storage Compartment The rear storage compartment cover is held by a spring- loaded latch. In order to remove the rear storage com- partment cover, use the following procedure: NOTE: The rear storage compartment latch should not be used as cargo tie-down. 1. Flip up the pull loop so it is perpendicular (straight up) to the top surface of the tray. 2. Pull up on the loop and twist it 90 degrees, so it is parallel to the slotted hole in the tray. 3. Open the rear compartment cover.

Rear Storage Cover

DUAL TOP — IF EQUIPPED If your vehicle is equipped with a Dual Top, you must remove one of the tops from the vehicle. If the soft top is removed, the pivot brackets must also be removed from the sport bar. The soft top was installed at the factory for shipping purposes only. The soft top and the

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155

• Two rear swing gate brackets 2. Remove the hard top. Refer to “Freedom Top Three- Piece Modular Hard Top — Front/Rear Panel Removal” in this section. 3. Remove the soft top bow assembly pivot bracket screws (two per side) using a #T30 Torx威 head driver.

hard top are to be used independently. Removal is mandatory to prevent any possible wear and tear on the soft top. Your vehicle warranty will not cover damage resulting from both tops remaining on the vehicle at the same time for extended periods of time. Removing the Soft Top

1. Locate and remove the two boxes that contain the following items: • Right and left door frames • Door frame attachment knobs (four for two-door models, six for four-door models) • Right and left quarter windows • Rear window • Two rear window roll up straps • Two Sunrider威 secure straps (if equipped)

156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Disconnect the knuckles from the left and right metal pivot brackets. Remove the soft top from the vehicle and store in a clean, dry location. NOTE: To aid in disconnecting the knuckles, you may carefully tap on the knuckles using a rubber mallet.

5. Unzip the zipper on the sport bar cover to expose the pivot brackets. Remove the brackets using a #T30 Torx威 head driver. Recover and re-zip the sports bar cover. Store the pivot brackets and screws in a safe place.

6. Reinstall the hard top. Refer to “Freedom Top Three- Piece Modular Hard Top — Front/Rear Panel Installa- tion” in this section.

Installing the Soft Top

NOTE: The following procedures are for first time set up only. For future soft top procedures, refer to “Soft Top” in this section. 1. Locate and remove the following items prior to hard top removal: • Right and left door frames • Door frame attachment knobs (four for two-door models, six for four-door models) • Right and left quarter windows • Rear window

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157
2. Remove the hard top. Refer to “Freedom Top Three- Piece Modular Hard Top — Front/Rear Panel Removal” in this section. 3. Install the door frames. Refer to “Door Frame” in this section. 4. If the soft top has been removed, follow these steps to reinstall the soft top. If the soft top is on the vehicle, proceed to step #5.

158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

a. If the pivot brackets have been removed, unzip the sport bar covers and attach the pivot brackets to the sports bar with the four screws that were removed using a #T30 Torx威 head driver. Re-cover and re-zip the sport bar covers.

b. Lay the soft top into the rear of the vehicle with the bows pointing forward and the curved portion of the bows facing upward. c. Reattach the knuckles onto the metal pivot brackets. NOTE: To aid in reattaching the knuckles, you may carefully tap on the knuckles using a rubber mallet.

d. Screw the pivot screws back into place using a #T30
Torx威 head driver. Secure them until they are snug, being careful not to cross-thread the screws or over- tighten.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159

CAUTION!

Do not overtighten the screws. You can strip the screws if they are overtightened.

5. Remove the swing gate bar (black metal bar for bottom of rear window) and set aside. NOTE: Be sure the wire harness in the left rear corner is not tangled in the soft top bows before you lift the top. 6. Unsnap and remove the black boot cover. This cover should be discarded. It was intended as a protective cover for shipping only. NOTE: A visual instruction sheet is enclosed in the dual top wrap. 7. Put up the soft top. Refer to “Soft Top — Putting Up the Soft Top” in this section.

160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE FREEDOM TOP™ THREE-PIECE MODULAR HARD TOP — IF EQUIPPED

CAUTION!

• The hard top is not designed to carry any addi- tional loads such as roof racks, spare tires, build- ing, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any additional loads other than environmen- tal (rain, snow, etc.). • Do not move your vehicle until the top has been either fully attached to the windshield frame and bodyside, or fully removed.

CAUTION!

Failure to follow these cautions may cause interior water damage, stains or mildew: • It is recommended that the top be free of water prior to panel removal. Removing the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicles interior. • The hard top assembly must be positioned prop- erly to ensure sealing. Improper installation can cause water to leak into the vehicles interior. • Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicles interior. • The front panel(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicles interior.

Front Panel(s) Removal

NOTE: Left panel must be removed before removing right panel. 1. Fold down the sun visor, and move it to the side. 2. Turn the rear fasteners (knobs) (located on the over- head speaker bar assembly) counterclockwise until they can be removed.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161
3. Turn the center L-shaped locks (two) from the center of the roof panel.

162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Turn the rear L-shaped lock (located above the shoul- der belt anchorage).

5. Unlatch the header panel latch located at the top of the windshield.

6. Remove the left-hand panel. To remove the right panel, follow the steps above except for Step 3.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163

Freedom Top™ Storage Bag Your vehicle comes with a Freedom Top™ storage bag that allows you to store your Freedom Top™ panels. The storage bag contains two compartments and fits behind the rear seat. Lay the Freedom bag down so the loops and hooks are facing downward. Unzip the bag and fold back the outer flap. Release the Velcro on the black panel divider and fold it back. NOTE: Ensure the front Freedom Top™ panel latch is closed prior to inserting the panel into the Freedom bag. Insert the right side Freedom panel into the bag with the latches facing downward.

164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Unfold the black panel divider (ensure the divider is laying flat). Secure the Velcro, located at the center of the divider.

NOTE: Ensure the front Freedom panel latch is closed prior to inserting the panel into the bag.

Insert the left-side Freedom panel into the bag with the latches facing upward.

Unfold the outer flap and zip the Freedom bag closed.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165
Install the seat attachment strap (at the top of the bag) through the loops.

166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lift the Freedom bag into the vehicle with the hooks and straps facing the back of the rear seat. Attach the clips at the bottom of the bag to the child restraint anchorages, located at the base of the rear seat.

Wrap the upper strap around the rear head restraints and loop the strap through the buckle. Pull on the strap to tighten the Freedom bag securely against the rear seat.

Front Panel(s) Installation

NOTE: Set the panels on the windshield frame so that there is no overhang. Also, make sure that the panels are sitting flush with the body. 1. Install the right panel first, then the left panel. 2. Reinstall the panel(s) using the same steps for removal in reverse order. Front Panel(s) Installation with Rear Hard Top Removed

1. Turn the left and right panels over and move the spacer block (located on the rear of the panel) upward 90
degrees.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167

NOTE: The front panel(s) must be positioned properly to ensure sealing. Set the panels on the windshield frame so that there is no overhang. Also, make sure that the panels are sitting flush with the body.

5. Open the swing gate all the way to ensure clearance of the rear window glass. Lift the rear window glass.

168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Install the right panel first, then the left panel. 3. Reinstall the panel(s) using the same steps for removal in reverse order. Rear Hard Top Removal

1. Remove both front panels. Refer to “Front Panel(s) Removal” in this section. 2. Open both doors. 3. Remove the two Torx威 head screws that secure the hard top at the B-pillar (near the top of the door) using a #40 Torx威 head driver (Four–Door Only). 4. Remove the six Torx威 head screws that secure the hard top to the vehicle (along the interior bodyside) using a #40 Torx威 head driver.

6. Locate the wire harness on the left rear inside corner of the vehicle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169

7. Release the red locking tab by pushing upward.

170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8. To remove the wiring harness press the side tab and pull to disconnect.

If necessary, pliers can be used to lightly squeeze

NOTE: grips while disconnecting the washer hose. 9. To remove the washer hose, pinch the grips on hose connector and pull.

10. Close the swing gate. 11. Remove the hard top from the vehicle. Place the hard top on a soft surface to prevent damage.

Rear Hard Top Installation

If the door frames are installed from soft top NOTE: usage, they must be removed prior to installation of the hard top. 1. Inspect the hard top seals for damage and replace if necessary. 2. Install the hard top using the same steps for removal in reverse order. Make sure that the hard top is sitting flush with the body at the sides and check to ensure that there is a uniform gap between the lift glass and hard top. NOTE: • The Torx fasteners that attach the hard top to the body should be torqued to 66 in lb +/- 22 in lb (7.5 N·m +/- 2.5 N·m)

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171

• It is not necessary to pinch connection when reinstall-

ing washer hose. Push on until click is heard.

DOOR FRAME

WARNING!

Do not drive your vehicle on pavement with the door frame(s) removed as you will lose the protection that they can provide. This procedure is furnished for use during off-road operation only.

CAUTION!

Failure to follow these cautions may cause interior water damage, stains or mildew: • Opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior.

(Continued)

172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION! (Continued)

• Careless handling and storage of the removable door frame(s) may damage the seals, causing water to leak into the vehicle’s interior. • The door frame(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior.

Door Frame Removal — Two-Door Models

1. Unscrew and remove the door frame attachment knobs (two per side).

WARNING!

Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used.

2. Place one hand on the upper rear and one hand on the front of the door frame. 3. Pull the frame toward you with your rearward hand to remove the frame from the vehicle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173

4. Screw the knobs back into the door frame and fold for storage. Store in a secure location.

WARNING!

Never store the door frames in your vehicle. In an event of an accident, a loose door frame many cause personal injury. If removed, always store the door frames outside of the vehicle.

174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Door Frame Installation — Two-Door Models

1. Unfold door frame and unscrew thumbscrews. 2. Set the door frame pin into the hole on top of the body side, behind the door opening.

3. After the door frame pin has been set into the body side hole, carefully set the front of the door frame into the rubber seal at the top of the windshield. 4. Starting with the front of the door frame, clip it over the metal side bar and then clip the rear, making sure that the material for the side bar covers is not pinched by the door frame.

5. Starting with the front knob, screw in and tighten both knobs. Repeat on the other side.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175

Door Frame Removal — Four-Door Models

1. Unscrew and remove the two forward most door frame attachment knobs.

Use both hands to remove the door frames. The door frames will fold and could cause injury if both hands are not used.

WARNING!

176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place one hand on the upper rear and one hand on the upper front of the front door frame.

4. Unscrew and remove the remaining door frame at- tachment knob on the rear door frame.

3. Pull the frame toward you with your front hand to remove the frame from the vehicle.

5. Place one hand on the upper rear and one hand on the upper front of the rear door frame. Pull the frame toward you with your rear hand to remove the frame from the vehicle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177

6. Screw the knob back into the door frame and fold for storage. Store in a secure location.

WARNING!

Never store the door frames in your vehicle. In an event of an accident, a loose door frame many cause personal injury. If removed, always store the door frames outside of the vehicle.

178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Door Frame Installation — Four-Door Models

1. Install the rear door frame first. 2. Set the door frame pin into the hole on top of the body side, just behind the rear door opening.

pinch the material of the sports bar covers and to ensure it is properly positioned on the seal above the front of the rear door.

3. Position the top of the door frame against the metal sport bar and press onto the side bar making sure not to

4. Loosely install the rear knob (long knob) to hold the door rail in position.

5. Carefully set the front of the front door frame in the rubber seal at the top of the windshield. Then, clip the front of the door rail over the side bar making sure that the material for the side bar cover is not pinched by the door frame. Position the rear of the front door frame to lay on top of the front of the rear door frame.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179
6. Loosely install both knobs beginning with the front knob (long knob). Then, install the middle knob (short knob) through the front and rear door frames and screw into the top of the B-pillar. 7. Tighten the front knob, then the rear most knob, and then the middle knob. Repeat this procedure for the other side.

180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SOFT TOP — TWO DOOR MODELS Please visit the owners section of Jeep.com for instruc- tional videos.

CAUTION!

The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunt- ing, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any addi- tional loads other than environmental (rain, snow, etc.).

If the temperature is below 72°F (24°C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up. This is caused by a natural contraction of the vinyl coating on the fabric top.

Place the vehicle in a warm area. Pull steadily on the top fabric. The vinyl will stretch back to its original size and the top can then be installed. If the temperature is 41°F (5°C) or below, do not attempt to put the top down or roll the rear or side curtains.

CAUTION!

• Do not run a fabric top through an automatic car wash. Window scratches and wax build up may result. • Do not lower the top when the temperature is below 41°F (5°C). Damage to the top may result. • Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered. • Do not lower the top with the windows installed.

Window and top damage may occur.

(Continued)

CAUTION! (Continued)

• Refer to “Appearance Care for Fabric Top Models” in “Maintaining Your Vehicle” for further infor- mation. It contains important information on cleaning and caring for your vehicle’s fabric top. • Do not use any tools (screwdrivers, etc.) to pry or force any of the clamps, clips, or retainers securing the soft top. Do not force or pry the soft top framework when opening or closing. Damage to the top may result.

WARNING!

• Do not drive the vehicle with the rear window curtain up unless the side curtains are also re- moved. Dangerous exhaust gases could enter the vehicle causing harm to the driver and passengers. (Continued)

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181

WARNING! (Continued)

• The fabric upper doors and fabric top are designed only for protection against the elements. Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident. Remember, always wear seat belts.

CAUTION!

Failure to follow these cautions may cause interior water damage, stains or mildew on the top material: • It is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior. (Continued)

182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION! (Continued)

• Careless handling and storage of the soft top may damage the seals, causing water to leak into the vehicle’s interior. • The soft top must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior.

Quick Steps to Lowering the Soft Top Refer to “Lowering the Soft Top” in this section for further information. 1. Remove the side and back windows.

2. Release header latches from the windshield frame.

3. Release the Sunrider威 latch (both sides).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183

184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Open the swing gate and lower the top. NOTE: Ensure fabric does not overhang the sides of the vehicle.

Quick Steps to Raising the Soft Top Refer to “Raising the Soft Top” in this section for further information. 1. Open the swing gate and raise the top, engaging the Sunrider威 latches (another person may be needed to help with this operation).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185

2. Engage header latches.

186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Install rear corner panels.

4. Install side and back windows.

Lowering The Soft Top

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187

1 — Header Bow 2 — 2–Bow 3 — 3–Bow 4 — Sail Panel 5 — Body Side Retainer

6 — Quarter Window 7 — Check Strap 8 — Front Retainer — Quarter Window 9 — Bottom Retainer — Quarter Window

188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

1 — Zipper Start 2 — Zipper Finish 3 — Swing Gate Bar 4 — Swing Gate Brackets 5 — Sail Panels

NOTE: Clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. If your vehicle has half doors, remove each half-door window by opening the door and lifting the half-door window out. NOTE: Stow the half-door windows carefully outside of the vehicle, never inside, to avoid scratches. 2. Unclip and move the sun visors to the side.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189
3. Release the header latches and leave the hooks in the loops on the windshield.

4. Open the swing gate.

190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets.

• Unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across the top and down to the left lower corner. Zipper pulls will stay on the rear window. Pull down on the rear window to disengage it from the zipper on the top cover. Stow the windows carefully to avoid scratch- ing.

6. Undo the Velcro威 that runs along the top and rear edge of the side window. 7. Beginning from the rear lower corner, completely unzip the window.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191
9. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle.

8. Once unzipped, remove the side window retainers from the door channel and body side channel. Repeat this step on the opposite side.

NOTE: When releasing the sail panel retainers, it is helpful to pull down on the rear roof bow.

192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 10. As you begin to lower the top, fold the sail panels so that they rest on top of the soft top.

11. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in toward the vehicle to disengage.

12. Completely release the latches from the loops on the windshield frame. If your vehicle is not equipped with

the Sunrider威 package, proceed to Step 15.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193
13. Make sure the plastic sleeves are slid rearward over the Sunrider威 link (Sunrider威 Models only).

194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 14. Unlatch the side bows from both door rails (Sun- rider威 Models only).

NOTE: Help from another person will ease this opera- tion.

15. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake light. Move to the front of the vehicle. Grasp the side bow behind the header and lift the top, folding it toward the rear of the vehicle.

16. Tuck the fabric and the check straps between the bows and as far inward as possible. This will keep any portion of the top from flapping outside of the vehicle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195

Raising the Soft Top

1. Unclip and move the sun visors to the side. 2. Install door frames, if removed. Refer to “Door Frame” in this section for further information. 3. Make sure the plastic sleeve is slid over Sunrider威 link (Sunrider威 Models only).

17. Close the front header latches. 18. Remove the door frames, if desired. Refer to “Door Frame” in this section for further information.

196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Standing on the side of the vehicle, lift the top by the side bow and the 2–bow (middle bow) up and over the sports bar until the header rests on the top of the windshield frame.

5. Make sure the Sunrider威 bracket on the side bows latches to the door rails (Sunrider威 Models only).

6. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197
7. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel until it snaps onto the exterior part of the rail. To be properly located, the bracket must only be clipped to the shortened rail edge.

198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8. Move to the rear of the vehicle and gently pull the sail panels over the rear roof bow.

9. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) toward the rear window loose (on both sides). Pulling down on the rear roof bow (3–bow) will aid to reach the channel with the retainers.

10. To install the side windows, affix the window tem- porarily by attaching to the Velcro威 in the rear corner. Start the zipper but close only about 1 in (2.5 cm).