2010 Jeep Wrangler Owners Manual

Download PDF Manual
• It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. (Continued) 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow these safety tips: Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. If you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. Safety Checks You Should Make Inside the Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Airbag Warning Light The light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an autho- rized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer is inoperable. Floor Mat Safety Information Always use floor mats designed to fit the foot well of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that for service if your defroster 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. WARNING! attached to the floor mat fasteners. Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • Always make sure that floor mats are properly • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and inter- fering with the pedals or the ability to control the vehicle. WARNING! (Continued) • Never put floor mats or other floor coverings on top of already installed floor mats. Additional floor mats and other coverings will reduce the size of the pedal area and interfere with the pedals. • Check mounting of mats on a regular basis. Al- ways properly reinstall and secure floor mats that have been removed for cleaning. • Always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • If required, mounting posts must be properly installed, if not equipped from the factory. (Continued) (Continued) WARNING! (Continued) Failure to properly follow floor mat installation or mounting can cause interference with the brake pedal and accelerator pedal operation causing loss of control of the vehicle. Periodic Safety Checks You Should Make Outside the Vehicle Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the tires (including spare) for proper pressure. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately. UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 86 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . 87 ▫ Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . 88 䡵 Uconnect™ Phone — If Equipped . . . . . . . . . . . 88 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 90 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . . 98 ▫ Uconnect™ Phone Features . . . . . . . . . . . . . 101 ▫ Advanced Phone Connectivity . . . . . . . . . . . 106 ▫ Things You Should Know About Your Uconnect™ Phone . . . . . . . . . . . . . . . . . . . . 108 ▫ General Information . . . . . . . . . . . . . . . . . . 119 䡵 Voice Command — If Equipped . . . . . . . . . . . 119 ▫ Voice Command System Operation . . . . . . . . 119 ▫ Commands . . . . . . . . . . . . . . . . . . . . . . . . 121 ▫ Voice Training . . . . . . . . . . . . . . . . . . . . . . 124 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 ▫ Front Seat Adjustment . . . . . . . . . . . . . . . . . 125 䡵 Seats 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Manual Seat Height Adjustment — If Equipped . . . . . . . . . . . . . . . . . . . . . . 126 ▫ Front Seatback Recline . . . . . . . . . . . . . . . . . 126 ▫ Front Easy Entry Seats — Two Door Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 . . . . . . . . . . . . . . . . . . . . . 128 ▫ Head Restraints ▫ Fold And Tumble Rear Seat — Two Door Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 ▫ Removing The Rear Seat — Two Door Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 ▫ Replacing The Rear Seat — Two Door Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 ▫ 60/40 Split Folding Rear Seat — Four Door Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 䡵 To Open And Close The Hood . . . . . . . . . . . . 135 䡵 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 ▫ Multifunction Lever . . . . . . . . . . . . . . . . . . 136 ▫ Headlights And Parking Lights . . . . . . . . . . 136 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . 137 ▫ Lane Change Assist . . . . . . . . . . . . . . . . . . . 138 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . 138 ▫ High/Low Beam Switch . . . . . . . . . . . . . . . 138 ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . 138 ▫ Front Fog Lights — If Equipped . . . . . . . . . . 138 ▫ Instrument Panel Dimmer . . . . . . . . . . . . . . 139 ▫ Daytime Running Lights — If Equipped . . . . 139 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . 140 䡵 Windshield Wipers And Washers . . . . . . . . . . 141 ▫ Windshield Wiper Operation . . . . . . . . . . . . 142 ▫ Intermittent Wiper System . . . . . . . . . . . . . . 143 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . 143 ▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . 144 䡵 Tilt Steering Column . . . . . . . . . . . . . . . . . . . 145 䡵 Electronic Speed Control — If Equipped . . . . . 146 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . 147 ▫ To Set a Desired Speed . . . . . . . . . . . . . . . . 147 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . 147 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . 147 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 ▫ Manual Transmission . . . . . . . . . . . . . . . . . 148 ▫ To Accelerate For Passing . . . . . . . . . . . . . . 149 䡵 Electrical Power Outlet . . . . . . . . . . . . . . . . . 150 䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 152 ▫ Front Cupholders . . . . . . . . . . . . . . . . . . . . 152 ▫ Rear Cupholders . . . . . . . . . . . . . . . . . . . . . 153 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 ▫ Console Storage Compartment . . . . . . . . . . . 153 ▫ Rear Storage Compartment . . . . . . . . . . . . . 154 䡵 Dual Top — If Equipped . . . . . . . . . . . . . . . . 154 ▫ Removing The Soft Top . . . . . . . . . . . . . . . . 155 ▫ Installing The Soft Top . . . . . . . . . . . . . . . . 157 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Freedom Top™ Three-Piece Modular Hard Top — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 160 ▫ Front Panel(s) Removal . . . . . . . . . . . . . . . . 161 ▫ Freedom Top™ Storage Bag . . . . . . . . . . . . . 163 ▫ Front Panel(s) Installation . . . . . . . . . . . . . . 167 ▫ Front Panel(s) Installation With Rear Hard Top Removed . . . . . . . . . . . . . . . . . . . . . . . 167 ▫ Rear Hard Top Removal . . . . . . . . . . . . . . . 168 ▫ Rear Hard Top Installation . . . . . . . . . . . . . . 171 . . . . . . . . . . . . . . . . . . . . . . . . . 171 ▫ Door Frame Removal — Two-Door Models . . 172 ▫ Door Frame Installation — Two-Door Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 䡵 Door Frame 䡵 Soft Top — Two Door Models ▫ Door Frame Removal — Four-Door Models . . 175 ▫ Door Frame Installation — Four-Door Models . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 . . . . . . . . . . . . 180 ▫ Quick Steps To Lowering The Soft Top . . . . . 182 ▫ Quick Steps To Raising The Soft Top . . . . . . . 184 ▫ Lowering The Soft Top . . . . . . . . . . . . . . . . 187 ▫ Raising The Soft Top . . . . . . . . . . . . . . . . . . 195 . . . . . . . . . . . . . 203 ▫ Quick Steps For Lowering The Soft Top . . . . 207 ▫ Quick Steps For Raising The Soft Top . . . . . . 210 ▫ Folding Down The Soft Top . . . . . . . . . . . . . 213 ▫ Putting Up The Soft Top . . . . . . . . . . . . . . . 222 䡵 Soft Top (Four-Door Models) 䡵 Sunrider威 (Two-Door Models) — If Equipped . 231 ▫ Opening The Sunrider威 . . . . . . . . . . . . . . . . 232 ▫ Closing The Sunrider威 . . . . . . . . . . . . . . . . 234 䡵 Sunrider威 (Four-Door Models) — If Equipped . 234 ▫ Opening The Sunrider威 . . . . . . . . . . . . . . . . 235 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 ▫ Closing The Sunrider威 . . . . . . . . . . . . . . . . 237 䡵 Rear Window Features — Hard Top Only . . . . 238 ▫ Rear Window Wiper/Washer — If Equipped . 238 ▫ Rear Window Defroster — If Equipped . . . . . 239 3 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield). Adjusting Rearview Mirror Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side mirror. Outside Rearview Mirror 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vanity Mirrors Vanity mirrors are located on the sun visors. To use the mirrors, rotate the sun visor down and swing the mirror cover upward. Vanity Mirror Uconnect™ Phone — IF EQUIPPED Uconnect™ Phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect™ Phone al- lows you to dial a phone number with your cellular phone using simple voice commands (e.g., ⬙Call” ѧ “Mike” ѧ”Work⬙ or ⬙Dial” ѧ “248-555-1212⬙). Your cellular phone’s audio is transmitted through your vehicle’s audio system; the system will automatically mute your radio when using the Uconnect™ Phone. NOTE: The Uconnect™ Phone requires a cellular phone equipped with the Bluetooth威 ⬙Hands-Free Profile,⬙ Ver- sion 0.96 or higher. See the Uconnect™ website for supported phones. For Uconnect™ customer support, visit the following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect • or call 1–877–855–8400 Uconnect™ Phone allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. is driven through your The Uconnect™ Phone Bluetooth威 phone. Profile” “Hands-Free Uconnect™ features Bluetooth威 technology - the global standard that enables different electronic devices to con- nect to each other without wires or a docking station, so Uconnect™ Phone works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s Uconnect™ Phone. The Uconnect™ Phone allows up to seven cellular phones to be linked to the cellular UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 system. Only one linked (or paired) cellular phone can be used with the system at a time. The system is available in English, Spanish, or French languages. WARNING! Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in an accident causing serious injury or death. Uconnect™ Phone Button The radio will contain the two control buttons button and Voice (Uconnect™ Phone button) that will enable you Command to access the system. When you press the button you will hear the word Uconnect™ followed by a BEEP. The beep is your signal to give a command. 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The driver side upper windshield trim contains the microphone for the Uconnect™ Phone. Voice Command Button Actual button location may vary with the ra- dio. The individual buttons are described in the “Operation” section. The Uconnect™ Phone can be used with any Hands-Free Profile certified Bluetooth威 cellular phone. See the Uconnect™ website for supported phones. Refer to your cellular service provider or the phone manufacturer for details. The Uconnect™ Phone is fully integrated with the vehi- cle’s audio system. The volume of the Uconnect™ Phone can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the Uconnect™ Phone such as ⬙CELL⬙ or caller ID on certain radios. Operation Voice commands can be used to operate the Uconnect™ Phone and to navigate through the Uconnect™ Phone menu structure. Voice commands are required after most Uconnect™ Phone prompts. You will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the beep, which follows the ⬙Ready⬙ prompt or another prompt. • For certain operations, compound commands can be used. For example, instead of saying ⬙Setup⬙ and then ⬙Phone Pairing,⬙ the following compound command can be said: ⬙Setup Phone Pairing.⬙ • For each feature explanation in this section, only the compound form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it. For example, you can use the compound form voice command ⬙Phonebook New Entry,⬙ or you can break the compound form command into two voice com- mands: ⬙Phonebook⬙ and ⬙New Entry.⬙ Please remem- ber, the Uconnect™ Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you. Voice Command Tree Refer to “Voice Tree” in this section. Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say ⬙Help⬙ following the beep. The Uconnect™ Phone will play all the options at any prompt if you ask for help. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 To activate the Uconnect™ Phone from idle, simply press the button and follow the audible prompts for directions. All Uconnect™ Phone sessions begin with a press of the button on the radio control head. Cancel Command At any prompt, after the beep, you can say ⬙Cancel⬙ and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (Link) Uconnect™ Phone to a Cellular Phone To begin using your Uconnect™ Phone, you must pair your compatible Bluetooth威 enabled cellular phone. To complete the pairing process, you will need to refer- ence your cellular phone Owner’s Manual. The Uconnect™ website may also provide detailed instruc- tions for pairing. button to begin. ⬙Setup Phone Pairing.⬙ follow the audible prompts. 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The following are general phone to Uconnect™ Phone pairing instructions: • Press the • After the ⬙Ready⬙ prompt and the following beep, say • When prompted, after the beep, say ⬙Pair a Phone⬙ and • You will be asked to say a four-digit Personal Identi- fication Number (PIN), which you will later need to enter into your cellular phone. You can enter any four-digit PIN. You will not need to remember this PIN after the initial pairing process. • For identification purposes, you will be prompted to give the Uconnect™ Phone a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between one and seven, with one being the highest priority. You can pair up to seven cellular phones to your Uconnect™ Phone. However, at any given time, only one cellular phone can be in use, connected to your Uconnect™ System. The priority allows the Uconnect™ Phone to know which cellular phone to use if multiple cellular phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the Uconnect™ Phone will use the priority three cellular phone when you make a call. You can select to use a lower priority cellular phone at any time (refer to ⬙Advanced Phone Connectivity⬙ in this section). Dial by Saying a Number • Press the • After the ⬙Ready⬙ prompt and the following beep, say button to begin. ⬙Dial.⬙ want to call. • The system will prompt you to say the number you • For example, you can say ⬙234-567-8901⬙. • The Uconnect™ Phone will confirm the phone number and then dial. The number will appear in the display of certain radios. “Call.⬙ button to begin. Call by Saying a Name • Press the • After the ⬙Ready⬙ prompt and the following beep, say • The system will prompt you to say the name of the • After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙John Doe,⬙ where John Doe is a previ- ously stored name entry in the Uconnect™ phonebook person you want to call. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 or downloaded phonebook. To learn how to store a name in the phonebook, refer to ⬙Add Names to Your Uconnect™ Phonebook,⬙ in the phonebook. • The Uconnect™ system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Add Names to Your Uconnect™ Phonebook NOTE: Adding names to the Uconnect™ Phonebook is recommended when the vehicle is not in motion. • Press the • After the ⬙Ready⬙ prompt and the following beep, say • When prompted, say the name of the new entry. Use of long names helps the Voice Command and it is recom- mended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.⬙ ⬙Phonebook New Entry.⬙ button to begin. 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, enter the number designation (e.g., ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired. • When prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an entry into the phone- book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The Uconnect™ Phone will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. In addition, if equipped and supported by your phone, Uconnect™ Phone automati- cally downloads your cellular phone’s phonebook. Phonebook Download – Automatic Phonebook Transfer From Cellular Phone If equipped and specifically supported by your phone, Uconnect™ Phone automatically downloads names (text names) and number entries from the cellular phone’s phonebook. Specific Bluetooth威 Phones with Phone Book Access Profile may support this feature. See Uconnect™ website for supported phones. • To call a name from downloaded (or Uconnect™) Phonebook, follow the procedure in “Call by Saying a Name” section. • Automatic download and update, if supported, begins as soon as the Bluetooth威 wireless phone connection is made to the Uconnect™ Phone, for example, after you start the vehicle. • A maximum of 1000 entries per phone will be down- loaded and updated every time a phone is connected to the Uconnect™ Phone. lar phone is accessible. • Depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used. Until then, if avail- able, the previous downloaded phonebook is available for use. • Only the phonebook of the currently connected cellu- • Only the cellular phone’s phonebook is downloaded. SIM card phonebook is not part of the Mobile phone- book. • This downloaded phonebook cannot be edited or deleted on the Uconnect™ Phone. These can only be edited on the cellular phone. The changes are trans- ferred and updated to Uconnect™ Phone on the next phone connection. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Phonebook Download — Single Entry If equipped and supported by your phone, Uconnect™ Phone allows the user to download entries from their phone via Bluetooth威. To use this feature, press the button and say “Phonebook Download.” The system prompts, “Ready to accept “V” card entry via Bluetooth威…” The system is now ready to accept phone- book entries from your phone using the Bluetooth威 Object Exchange Profile (OBEX). Please see your phone Owner’s Manual for specific instructions on how to send these entries from your phone. NOTE: • The phone handset must support Bluetooth威 OBEX transfers of phonebook entries to use this feature. 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Some phones cannot send phonebook entries if they are already connected to any system via Bluetooth威, and you may see a message on the phone display that the Bluetooth威 link is busy. In this case, the user must first disconnect or drop the Bluetooth威 connection to the Uconnect™ phone, and then send the address book entry via Bluetooth威. Please see your phone Owner’s Manual for specific instructions on how to drop the Bluetooth威 connection. • If the phonebook entry is longer than 24 characters, it will only use the first 24 characters. Edit Uconnect™ Phonebook Entries NOTE: • Editing names in the phonebook is recommended • Automatic downloaded phonebook entries cannot be when the vehicle is not in motion. deleted or edited. button to begin. ⬙Phonebook Edit.⬙ • Press the • After the ⬙Ready⬙ prompt and the following beep, say • You will then be asked for the name of the phonebook • Next, choose the number designation (home, work, • When prompted, recite the new phone number for the cellular, or pager) that you wish to edit. entry that you wish to edit. phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. ⬙Phonebook Edit⬙ can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a cellular and a home number, but you can add ”John Doe’s” work number later using the ⬙Phonebook Edit⬙ feature. Delete Uconnect™ Phonebook Entry NOTE: Editing phonebook entries is recommended when the vehicle is not in motion. • Press the button to begin. • After the ⬙Ready⬙ prompt and the following beep, say • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say ⬙List Names⬙ to hear a list of the entries in the phonebook from which you choose. To select one of the entries ⬙Phonebook Delete.⬙ UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 from the list, press the button while the Uconnect™ Phone is playing the desired entry and say ⬙Delete.⬙ • After you enter the name, the Uconnect™ Phone will ask you which designation you wish to delete: home, work, cellular, pager, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current • Automatic downloaded phonebook entries cannot be language is deleted. deleted or edited. Delete/Erase “All” Uconnect™ Phonebook Entries • Press the • After the ⬙Ready⬙ prompt and the following beep, say button to begin. ⬙Phonebook Erase All.⬙ 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE wish to delete all the entries from the phonebook. • The Uconnect™ Phone will ask you to verify that you • After confirmation, the phonebook entries will be • Note that only the phonebook in the current language • Automatic downloaded phonebook entries cannot be is deleted. deleted. deleted or edited. button to begin. List All Names in the Uconnect™ Phonebook • Press the • After the ⬙Ready⬙ prompt and the following beep, say • The Uconnect™ Phone will play the names of all the phonebook entries, including the downloaded phone- book entries, if available. ⬙Phonebook List Names.⬙ • To call one of the names in the list, press the button during the playing of the desired name, and say ⬙Call.⬙ NOTE: The user can also exercise ⬙Edit⬙ or ⬙Delete⬙ operations at this point. • The Uconnect™ Phone will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed through the Uconnect™ Phone if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the Uconnect™ Phone. Check with your cellular service provider for the features that you have. indicating that Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the Uconnect™ Phone will interrupt the vehicle audio sys- tem, if on, and will ask if you would like to answer the button to accept the call. To reject the call. Press the button until you hear a call, press and hold the single beep, the incoming call was rejected. Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your button to place the current cellular phone. Press the call on hold and answer the incoming call. NOTE: The Uconnect™ Phone compatible phones in the market today do not support rejecting an incoming call UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 when another call is in progress. Therefore, the user can only answer an incoming call or ignore it. Making a Second Call While Current Call is in Progress To make a second call while you are currently on a call, button and say ⬙Dial⬙ or ⬙Call⬙ followed press the by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to ⬙Toggling Between Calls⬙ in this section. To combine two calls, refer to ⬙Conference Call⬙ in this section. Place/Retrieve a Call From Hold To put a call on hold, press the button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the button until you hear a single beep. 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Toggling Between Calls If two calls are in progress (one active and one on hold), button until you hear a single beep, press the indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at a time. Conference Call When two calls are in progress (one active and one on button until you hear a hold), press and hold the double beep indicating that the two calls have been joined into one conference call. Three-Way Calling button To initiate three-way calling, press the while a call is in progress, and make a second phone call, as described under ⬙Making a Second Call While Current Call is in Progress.⬙ After the second call has established, button until you hear a double press and hold the beep, indicating that the two calls have been joined into one conference call. Call Termination To end a call in progress, momentarily press the button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the button until you hear a single beep. button to begin. Redial • Press the • After the ⬙Ready⬙ prompt and the following beep, say • The Uconnect™ Phone will call the last number that ⬙Redial.⬙ was dialed from your cellular phone. NOTE: This may not be the last number dialed from the Uconnect™ Phone. Call Continuation Call continuation is the progression of a phone call on the Uconnect™ Phone after the vehicle ignition key has been switched to OFF. Call continuation functionality avail- able on the vehicle can be any one of three types: • After the ignition key is switched to OFF, a call can continue on the Uconnect™ Phone either until the call ends, or until the vehicle battery condition dictates cessation of the call on the Uconnect™ Phone and transfer of the call to the cellular phone. • After the ignition key is switched to OFF, a call can continue on the Uconnect™ Phone for a certain dura- tion, after which the call is automatically transferred from the Uconnect™ Phone to the cellular phone. • An active call is automatically transferred to the cellular phone after the ignition key is switched to OFF. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Uconnect™ Phone Features Language Selection To change the language that the Uconnect™ Phone is using: • Press the • After the ⬙Ready⬙ prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais. • Continue to follow the system prompts to complete button to begin. the language selection. After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every Uconnect™ Phone language change operation, only the language-specific 32-name phone- book is usable. The paired phone name is not language- specific and usable across all languages. 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Emergency Assistance If you are in an emergency and the cellular phone is reachable: • Pick up the phone and manually dial the emergency number for your area. button to begin. If the phone is not reachable and the Uconnect™ Phone is operational, you may reach the emergency number as follows: • Press the • After the ⬙Ready⬙ prompt and the following beep, say ⬙Emergency⬙ and the Uconnect™ Phone will instruct the paired cellular phone to call the emergency num- ber. This feature is supported in the U.S., Canada, and Mexico. NOTE: • The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area. • If supported, this number may be programmable on button and • The Uconnect™ Phone does slightly lower your chances of successfully making a phone call as to that for the cellular phone directly. some systems. To do this, press the say ‘Setup’, followed by ‘Emergency’. WARNING! To use your Uconnect™ Phone System in an emer- gency, your cellular phone must be: • turned on, • paired to the Uconnect™ System, • and have network coverage. Towing Assistance If you need towing assistance: • Press the • After the ⬙Ready⬙ prompt and the following beep, say button to begin. ⬙Towing Assistance.⬙ NOTE: • The towing assistance number dialed is based on the country where the vehicle is purchased (1-800-528- 2069 for the U.S., 1-877-213-4525 for Canada, 55-14- 3454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico). Please refer to the 24-Hour Towing Assistance coverage details on the DVD in the Warranty Information Booklet and the 24-Hour Tow- ing Assistance references. • If supported, this number may be programmable on button and some systems. To do this, press the say “Setup”, followed by “Towing Assistance”. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Paging To learn how to page, refer to ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the Uconnect™ Phone. Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.⬙ Working with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system. You can use your Uconnect™ Phone to access a voice mail system or an automated service, such as a paging service or automated customer service line. Some ser- vices require immediate response selection. In some instances, the Uconnect™ Phone. that may be too quick for use of 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your Uconnect™ Phone that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can press the button and say the sequence you wish to enter, followed by the word ⬙Send.⬙ For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you can button and say, ⬙3 7 4 6 #Send.⬙ Saying press the a number, or sequence of numbers, followed by ⬙Send,⬙ is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can also send stored Uconnect™ Phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you wish to button and say, “Send.” The call and then press the system will prompt you to enter the name or number and say the name of the phonebook entry you wish to send. The Uconnect™ Phone will then send the corresponding phone number associated with the phonebook entry, as tones over the phone. NOTE: • You may not hear all of the tones due to cellular phone • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature. network configurations. This is normal. Barge In - Overriding Prompts The “Voice Command” button can be used when you wish to skip part of a prompt and issue your voice command immediately. For example, if a prompt is asking ⬙Would you like to pair a phone, clear a...,⬙ you button and say, ⬙Pair a Phone⬙ to could press the select that option without having to listen to the rest of the voice prompt. button to begin. Turning Confirmation Prompts ON/OFF Turning confirmation prompts off will stop the system from confirming your choices (e.g., the Uconnect™ Phone will not repeat a phone number before you dial it). • Press the • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Confirmations.⬙ The Uconnect™ Phone will play the current confirmation prompt status and you will be given the choice to change it. Phone and Network Status Indicators If available on the radio and/or on a premium display such as the instrument panel cluster, and supported by your cellular phone, the Uconnect™ Phone will provide notification to inform you of your phone and network status when you are attempting to make a phone call using Uconnect™ Phone. The status is given for roaming, network signal strength, phone battery strength, etc. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the Uconnect™ Phone (while dialing via the cellular phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth威 cellular phone, the audio will be played through your vehicle’s audio system. The Uconnect™ Phone will work the same as if you dial the number using Voice Command. NOTE: Certain brands of cellular phones do not send the dial ring to the Uconnect™ Phone to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number the user may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio. 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mute/Un-Mute (Mute OFF) When you mute the Uconnect™ Phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the Uconnect™ Phone: • Press the • Following the beep, say ⬙Mute.⬙ In order to un-mute the Uconnect™ Phone: • Press the • Following the beep, say ⬙Mute off.⬙ Advanced Phone Connectivity button. button. Transfer Call to and from Cellular Phone The Uconnect™ Phone allows ongoing calls to be trans- ferred from your cellular phone to the Uconnect™ Phone without terminating the call. To transfer an ongoing call from your Uconnect™ Phone paired cellular phone to the Uconnect™ Phone or vice versa, press the button and say ⬙Transfer Call.⬙ Connect or Disconnect Link Between the Uconnect™ Phone and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively ⬙connected⬙ with one electronic device at a time. If you would like to connect or disconnect the Bluetooth威 connection between a Uconnect™ Phone paired cellular phone and the Uconnect™ Phone, follow the instructions described in your cellular phone User’s Manual. List Paired Cellular Phone Names • Press the • After the “Ready” prompt and the following beep, say button to begin. “Setup Phone Pairing.” • When prompted, say ⬙List Phones.⬙ • The Uconnect™ Phone will play the phone names of all paired cellular phones in order from the highest to the lowest priority. To “select” or “delete” a paired button and phone being announced, press the say “Select” or “Delete.” Also, see the next two sec- tions for an alternate way to “select” or “delete” a paired phone. button to begin. Select Another Cellular Phone This feature allows you to select and start using another phone paired with the Uconnect™ Phone. • Press the • After the ⬙Ready⬙ prompt and the following beep, say • You can also press the button at any time while the list is being played, and then choose the phone that you wish to select. ⬙Setup Select Phone⬙ and follow the prompts. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • The selected phone will be used for the next phone call. the Uconnect™ Phone will return to using the highest priority phone present in or near (approximately within 30 ft (9 m)) the vehicle. the selected phone is not available, If button to begin. ⬙Setup Phone Pairing.⬙ Delete Uconnect™ Phone Paired Cellular Phones • Press the • After the ⬙Ready⬙ prompt and the following beep, say • At the next prompt, say ⬙Delete⬙ and follow the • You can also press the button at any time while the list is being played, and then choose the phone you wish to delete. prompts. 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your Uconnect™ Phone Uconnect™ Phone Tutorial To hear a brief tutorial of the system features, press the button and say “Uconnect™ Tutorial.” Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers, the Uconnect™ Phone Voice Training feature may be used. To enter this training mode, follow one of the two following proce- dures: From outside the Uconnect™ Phone mode (e.g., from radio mode): • Press and hold the • Press the button and say the ⬙Setup, Voice button for five seconds until the session begins, or, Training⬙ command. You can either press the Uconnect™ Phone button to restore the factory setting or repeat the words and phrases when prompted by the Uconnect™ Phone. For best results, the Voice Training session should be com- pleted when the vehicle is parked with the engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only. Reset • press the • After the “Ready” prompt, and the following beep, say button. “Uconnect™ Setup”, then “Reset”. This will delete all phone pairing, phone book entries, and other settings in all language modes. The System will prompt you before resetting to factory settings. Voice Command • For best performance, adjust the rearview mirror to provide at least 1⁄2 in (1 cm) gap between the overhead console (if equipped) and the mirror. • Always wait for the beep before speaking. • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. • Make sure that no one other than you is speaking during a Voice Command period. • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work for some. • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say ⬙Send.⬙ • Storing names in the phonebook when the vehicle is • It is not recommended to store similar sounding • Phonebook (Downloaded and Uconnect™ Phone Lo- cal) name recognition rate is optimized when the entries are not similar. names in the Uconnect™ Phonebook. not in motion is recommended. 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE be spoken “eight-zero-zero” not “eight hundred”. • Numbers must be spoken in single digits. “800” must • You can say ⬙O⬙ (letter ⬙O⬙) for ⬙0⬙ (zero). • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. • In a convertible vehicle, system performance may be compromised with the convertible top down. Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the Uconnect™ Phone. • Echo at the phone far end can sometimes be reduced • In a convertible vehicle, system performance may be by lowering the in-vehicle audio volume. compromised with the convertible top down. Recent Calls If your phone supports “Automatic Phonebook Down- load”, Uconnect™ Phone can list your Outgoing, Incom- ing and Missed Calls. SMS Uconnect™ Phone can read or send new messages on your phone. Read Messages: If you receive a new text message while your phone is connected to Uconnect™ Phone, an announcement will be made to notify you that you have a new text message. If you wish to hear the new message: • Press the • After the “Ready” prompt and the following beep, say • Uconnect™ Phone will play the new text message for “SMS Read” or “Read Messages.” button. you. After reading a message, you can “Reply” or “Forward” the message using Uconnect™ Phone. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Send Messages: You can send messages using Uconnect™ Phone. To send a new message: • Press the • After the “Ready” prompt and the following beep, say • You can either say the message you wish to send or say “SMS Send” or “Send Messages.” button. “List Messages.” There are 20 preset messages. To send a message, press the system is listing the message and say “Send.” Uconnect™ Phone will prompt you to say the name or number of the person you wish to send the message to. button while the 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE List of Preset Messages: 1. Yes 2. No 3. Where are you? 4. I need more direction. 5. L O L 6. Why 7. I love you 8. Call me 9. Call me later 10. Thanks 11. See You in 15 minutes 12. I am on my way 13. I’ll be late 14. Are you there yet? 15. Where are we meeting? 16. Can this wait? 17. Bye for now 18. When can we meet 19. Send number to call 20. Start without me Turn SMS Incoming Announcement ON/OFF Turning the SMS Incoming Announcement OFF will stop the system from announcing the new incoming mes- sages. • Press the • After the “Ready” prompt and the following beep, say “Setup, Incoming Message Announcement,” you will then be given a choice to change it. button. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Bluetooth威 Communication Link Cellular phones have been found to lose connection to the Uconnect™ Phone. When this happens, the connec- tion can generally be reestablished by switching the phone off/on. Your cellular phone is recommended to remain in Bluetooth威 ON mode. Power-Up After switching the ignition key from OFF to either the ON or ACC position, or after a language change, you must wait at least five seconds prior to using the system. 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Alternate(s) Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Voice Commands Alternate(s) Primary call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Alternate(s) pairing phone book Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again Voice Commands Alternate(s) return or main menu select phone settings or phone set up Primary redial return to main menu select phone send set up towing assistance transfer call Uconnect™ Tutorial try again voice training work yes General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. VOICE COMMAND — IF EQUIPPED Voice Command System Operation This Voice Command system allows you to control your AM, FM radio, satellite radio, disc player, and a memo recorder. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 NOTE: Take care to speak into the Voice Interface System as calmly and normally as possible. The ability of the Voice Interface System to recognize user voice com- mands may be negatively affected by rapid speaking or a raised voice level. WARNING! Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in an accident causing serious injury or death. button, you When you press the Voice Command will hear a beep. The beep is your signal to give a command. 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you do not say a command within a few NOTE: seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists button, listen options, press the Voice Command for the beep, and say your command. button while the Pressing the Voice Command system is speaking is known as “barging in.” The system will be interrupted, and after the beep, you can add or change commands. This will become helpful once you start to learn the options. NOTE: At any time, you can say the words “Cancel”, “Help” or “Main Menu”. These commands are universal and can be used from any menu. All other commands can be used depending upon the active application. For example, if you are in the disc menu and you are listening to FM radio, you can speak commands from the disc menu or from the FM radio menu. When using this system, you should speak clearly and at a normal speaking volume. The system will best recognize your speech if the win- dows are closed, and the heater/air conditioning fan is set to low. At any point, if the system does not recognize one of your commands, you will be prompted to repeat it. To hear the first available Menu, press the Voice button and say “Help” or “Main Command Menu”. Commands The Voice Command system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the Volume 1. Start a dialogue by pressing the Voice Command button. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Command system is speaking. Please note the volume setting for Voice Command is different than the audio system. Main Menu Start a dialogue by pressing the Voice Command button. You may say “Main Menu” to switch to the main menu. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 In this mode, you can say the following commands: • “Radio” (to switch to the radio mode) • “Disc” (to switch to the disc mode) • “Memo” (to switch to the memo recorder) • “System Setup” (to switch to system setup) Radio AM (or Radio Long Wave or Radio Medium Wave — If Equipped) To switch to the AM band, say “AM” or “Radio AM”. In this mode, you may say the following commands: • “Frequency” (to change the frequency) • “Next Station” (to select the next station) • “Previous Station” (to select the previous station) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Radio FM To switch to the FM band, say “FM” or “Radio FM”. In this mode, you may say the following commands: • “Frequency” (to change the frequency) • “Next Station” (to select the next station) • “Previous Station” (to select the previous station) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Satellite Radio To switch to satellite radio mode, say “Sat” or “Satellite Radio”. In this mode, you may say the following com- mands: • “Channel Number” (to change the channel by its • “Next Channel” (to select the next channel) spoken number) • “Previous Channel” (to select the previous channel) • “List Channel” (to hear a list of available channels) • “Select Name” (to say the name of a channel) • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Disc To switch to the disc mode, say “Disc”. In this mode, you may say the following commands: • “Track” (#) (to change the track) • “Next Track” (to play the next track) • “Previous Track” (to play the previous track) • “Main Menu” (to switch to the main menu) Memo To switch to the voice recorder mode, say “Memo”. In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the recording, you may press the Voice Command button to stop recording. You proceed by saying one of the following commands: − “Save” (to save the memo) − “Continue” (to continue recording) − “Delete” (to delete the recording) • “Play Memos” (to play previously recorded memos) — During the playback you may press the Voice button to stop playing memos. You Command proceed by saying one of the following commands: − “Repeat” (to repeat a memo) − “Next” (to play the next memo) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 − “Previous” (to play the previous memo) − “Delete” (to delete a memo) • “Delete All” (to delete all memos) System Setup To switch to system setup, say “Setup”. In this mode, you may say the following commands: • “Language German” • “Language Dutch” • “Language Italian” • “Language English” • “Language French” • “Language Spanish” • “Tutorial” • “Voice Training” 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Keep in mind that you have to press the Voice button first and wait for the beep Command before speaking the “Barge In” commands. Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers the Uconnect™ Voice “Voice Training” feature may be used. button, say “System 1. Press the Voice Command Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition. 2. Repeat the words and phrases when prompted by Uconnect™ Voice. For best results, the “Voice Training” session should be completed when the vehicle is parked, engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only. SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. They need to be used properly for safe operation of the vehicle. WARNING! • DO NOT allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Front Seat Adjustment Move the seat forward or rearward by lifting the lever. Release the lever when the seat is in the desired position. Using body pressure, move forward and rearward on the seat to make sure that the latch is fully engaged. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Only adjust a seat while the vehicle is parked. Manual Seat Adjustment 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seat Height Adjustment — If Equipped The driver’s seat height can be raised or lowered by using the ratcheting handle, located on the outboard side of the seat. Pull upward on the handle to raise the seat; push downward on the handle to lower the seat. Front Seatback Recline Lean forward before lifting the handle, then lean back to the desired position and release the handle. Lift the handle to return the seatback to an upright position. Seat Height Adjustment Recline Lever WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seatbelt and be seriously or fatally injured. Use the recliner only when the vehicle is parked. Front Easy Entry Seats — Two Door Models Push the lever on the seatback rearward (toward the rear of the vehicle) to tilt the entire seat forward. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Easy Entry Combination Lever 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Easy Entry Seat With Combination Lever 1. To return the seat to a sitting position, rotate the seatback upright until it locks. 2. Push the seat rearward until the track locks. NOTE: • If equipped with combination lever the seatback will return to its first locked position. The recliner handle will have to be actuated to adjust the seatback to the desired reclined position. • The front passenger seats have a track memory, which returns the seat to just past the halfway point of the track regardless of its original position. • The recliner and easy entry levers should not be used during the automatic returning of the seat to its sitting position. Head Restraints Head restraints can reduce the risk of injury in the event of a rear impact. The head restraint should be adjusted so the top of the head restraint is located above the top of your ear. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the large button, located on the base of the head restraint, and push downward on the head restraint. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 NOTE: The rear head restraints are not adjustable. To remove the head restraint, pull upward on the head restraint to it’s highest position, push in both buttons at the base of each head restraint rod, and simultaneously pull up on the head restraint. Adjustable Head Restraints Removing Head Restraint 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To install the head restraint, insert the head restraint rods into each guide, apply pressure down on the headrest until the head restraint reaches the first lock position, push the large button in and push down and adjust head restraint to desired position. NOTE: Ensure that the front of the head restraint is facing toward the front of the vehicle. WARNING! Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to operating the vehicle and never adjusted while the vehicle is in motion. Always adjust the head restraints when the vehicle is in PARK. Fold and Tumble Rear Seat — Two Door Models NOTE: • Prior to folding the rear seat, it may be necessary to • Be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. reposition the front seats. 1. Lift the seatback release lever and fold the seatback forward. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Rear Seat Release 2. Slowly flip the entire seat forward. Folding Rear Seat 3. Return the seat to the normal position. 4. Raise the rear seatback using the assist strap and firmly lock the seat into position. 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Removing the Rear Seat — Two Door Models WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and • In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure that the seats are fully latched. using a seat belt properly. 1. Remove the three rear subwoofer mounting nuts using a 15 mm socket. (if equipped) Subwoofer 2. Unplug the electrical connector from the rear sub- woofer (if equipped). 3. Fold the rear seat forward following steps 1 through 3 under “Fold and Tumble Rear Seat” in this section. 4. Press down on the release bar on each side, and pull the seat out and away from the lower bracket. 5. Remove the seat from the vehicle. Release Bar Location UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Replacing the Rear Seat — Two Door Models Reverse the steps for removing the seat. WARNING! • To help protect against personal injury, passengers should not be seated in the rear cargo area with the rear seat folded down or removed from the ve- hicle. • The rear cargo space is intended for load carrying purposes only, not for passengers who should sit in seats and use seat belts. 60/40 Split Folding Rear Seat — Four Door Models To provide additional storage area, each rear seat can be folded flat to allow for extended cargo space and still maintain some rear seating room. reposition the front seat to its mid-track position. 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Prior to folding the rear seat, it may be necessary to • Be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. To Fold Down the Rear Seat Locate the pull strap (lower outboard side of seat), and pull it toward you until the seatback releases. Pull Strap To Raise the Rear Seat Raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. If the rear seatback is not fully latched, the NOTE: center shoulder belt will not be able to be extended for use. If you cannot extend the center shoulder belt, make sure your seatback is fully latched. WARNING! Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 TO OPEN AND CLOSE THE HOOD Release both the hood latches. Hood Latch Raise the hood and locate the safety latch, located in the middle of the hood opening. Push the latch to the left side of the vehicle, to open the hood. You may have to push down slightly on the hood before pushing the safety latch. Insert the support rod into the slot on the hood. 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To close the hood, remove the support rod from the hood panel and place it in the retaining clip. Lower the hood slowly. Secure both of the hood latches. WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. LIGHTS Multifunction Lever The multifunction lever controls the operation of the parking lights, headlights, headlight beam selection, passing light, fog lights, instrument panel light dimming and turn signals. The lever is located on the left side of the steering column. Multifunction Lever Headlights and Parking Lights Turn the end of the multifunction lever to the first detent for parking lights and instrument panel lights. Turn to the second detent for headlight operation. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Headlight Switch NOTE: Lens fogging can occur under certain weather conditions. Turning the headlights on will usually accel- erate the clearing process. Turn Signal Operation 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. • A tone will chime if the turn signals are left on for more than 1 mile (2 km). Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Lights-On Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound when the driver’s door is opened. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headlights back to low beam. Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward the steer- ing wheel. This will turn on the high beam headlights until the lever is released. Front Fog Lights — If Equipped The front fog light switch is located on the multi- function lever. To activate the front fog lights, turn on the parking or low beam headlights and pull out the end of the lever. NOTE: The fog lights will only operate with the parking lights or the headlights on low beam. Selecting high beam headlights will turn off the fog lights. Instrument Panel Dimmer Rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the park- ing lights or headlights are on. Rotate the center portion of the lever upward to the next detent position to brighten the odometer and radio when the parking lights or headlights are on. Rotate the center portion of the lever upward to the last detent to turn on the interior lighting. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Dimmer Control Daytime Running Lights — If Equipped The headlights come on at a low intensity level after the vehicle has been driven approximately 3 ft (1 m). They will turn off when the vehicle is turned off or when the headlights are switched on. The rearmost cargo lamp (available on four-door models) may be turned on by pressing either of the switches, located on either side of the lens. Press a switch a second time to turn the light off. Also, the rear cargo lamp may be turned on by pressing the lens. Press the lens a second time to turn the light off. 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights The overhead light will turn on when a door is opened. It may also be turned on by rotating the control for the dimmer switch on the multifunction lever fully upward. The overhead light will automatically turn off in approxi- mately 10 minutes if a door is left open or the dimmer control is left in the dome light position. Turn the ignition switch ON to restore the overhead light operation. Cargo Lamp The courtesy and dome lights will turn on when the front doors are opened, by rotating the control for the dimmer switch on the multifunction lever fully upward, or if equipped, when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter. Cargo Lamp When a door is open and the interior lights are on, rotating the dimmer control to the extreme bottom posi- tion will cause all the interior lights to turn off. This is also known as the ⬙Party⬙ mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery. WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located at the end of the lever. For information on using the rear window wiper/ washer, refer to “Rear Window Features” in “Under- standing the Features of Your Vehicle”. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Windshield Wiper/Washer Lever 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper opera- tion. Front Wiper Control CAUTION! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted. Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Rotate the end of the lever to the first detent position for one of five intermittent settings. The delay cycle can be set anywhere between 2 to 30 seconds. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Front Wiper Control Windshield Washers To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for two or three wipe cycles after the lever is released, and then resume the intermittent interval previously selected. 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the lever is pulled while in the off position, the wipers will operate for two or three wipe cycles and then turn off. WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use. Mist Feature Push down on the wiper lever to activate a single wipe to clear off road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. Mist Control NOTE: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid. TILT STEERING COLUMN This feature allows you to tilt the steering column upward or downward. The tilt lever is located on the steering column, below the turn signal lever. Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Pull upwards on the lever to lock the column firmly in place. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Tilt Steering Column 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this warning may result in serious injury or death. ELECTRONIC SPEED CONTROL — IF EQUIPPED Electronic Speed Control takes over the accelerator op- eration at speeds greater than 25 mph (40 km/h). The Electronic Speed Control lever is located on the right side of the steering wheel. Electronic Speed Control Lever In order to ensure proper operation, the Elec- NOTE: tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button. The Cruise Indicator Light in the instrument cluster will illuminate. To turn the Elec- tronic Speed Control system off, push the ON/OFF button a second time. The cruise indicator light will turn off. The Electronic Speed Control system should be turned off when not in use. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the Electronic Speed Control system off when you are not using it. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 To Set a Desired Speed Turn the Electronic Speed Control ON. When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed. NOTE: The vehicle should be traveling at a steady speed and on level ground before pressing the SET lever. To Deactivate A soft tap on the brake pedal, pulling the Electronic Speed Control lever toward you, or normal brake or clutch pressure while slowing the vehicle will deactivate Electronic Speed Control without erasing the set speed memory. Pressing the ON/OFF button or turning the ignition switch OFF erases the set speed memory. To Resume Speed To resume a previously set speed, push the RESUME ACCEL lever up and release. Resume can be used at any speed above 25 mph (40 km/h). 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary the Speed Setting When the Electronic Speed Control is set, you can in- crease speed by pushing up and holding the RESUME ACCEL lever. If the lever is continually held in the RESUME ACCEL position, the set speed will continue to increase until the lever is released, then the new set speed will be established. Tapping RESUME ACCEL once will result in a 1 mph (1.6 km/h) speed increase. Each time the Electronic Speed Control lever is tapped, speed increases so that tapping the Electronic Speed Control lever three times will increase speed by 3 mph (4.8 km/h), etc. To decrease speed while the Electronic Speed Control is set, push down and hold the SET DECEL lever. If the lever is continually held in the SET DECEL position, the set speed will continue to decrease until the lever is released. Release the lever when the desired speed is reached, and the new set speed will be established. Tapping the SET DECEL lever once will result in a 1 mph (1.6 km/h) speed decrease. Each time the lever is tapped, speed decreases. Manual Transmission Pressing the clutch pedal will disengage the Electronic Speed Control. A slight increase in engine RPM before the Electronic Speed Control disengages is normal. Vehicles equipped with manual transmissions may need to be shifted into a lower gear to climb hills without speed loss. WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery. To Accelerate for Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 On steep hills, a greater speed loss or gain and/or more frequent downshifts (auto transmission only) may occur so it may be preferable to drive without Electronic Speed Control. WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery. 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLET There are two 12 Volt (13 Amp) auxiliary power outlets that can provide power for accessories designed for use with the standard power outlet adapters. The power outlet, located in the lower portion of the instrument panel, has a snap-on plastic cap so that it can be covered when not in use. When the optional cigar lighter heating element is used in the left-side power outlet, it heats when pushed in and pops out automatically when ready for use. To preserve the heating element, do not hold the lighter in the heating position. NOTE: Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. Power Outlets The left-side power outlet is powered when the key is in the ON or ACC positions. The right-side power outlet is powered directly from the battery (power available at all times). Items plugged into this power outlet may discharge the battery and/or prevent the engine from starting. WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving • If this outlet is mishandled, it may cause an the vehicle. electric shock and failure. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 CAUTION!

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2010 Jeep Wrangler Owners Manual