2009 Jeep Wrangler Owners Manual

battery may freeze. Do not attempt jump starting because the battery could rupture or explode. The battery temperature must be brought up above the freezing point before attempting a jump-start.

EMERGENCY TOW HOOKS — IF EQUIPPED If your vehicle is equipped with tow hooks, they are mounted in the front and the rear. NOTE: For off-road recovery, it is recommended to use both of the front tow hooks to minimize the risk of damage to the vehicle.

WARNING!

• Chains are not recommended for freeing a stuck vehicle. chains may break, causing serious injury or death. • Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury.

CAUTION!

Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. Tow straps are recommended when towing the vehicle, chains may cause vehicle damage.

WHAT TO DO IN EMERGENCIES 397

TOWING A DISABLED VEHICLE The manufacturer recommends towing with all four wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the other end on a towing dolly.

MAINTAINING YOUR VEHICLE

CONTENTS

䡵 Engine Compartment – 3.8L . . . . . . . . . . . . . . 401
䡵 Onboard Diagnostic System — OBD II . . . . . . 402
▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 402

䡵 Emissions Inspection And Maintenance

Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403
䡵 Replacement Parts . . . . . . . . . . . . . . . . . . . . . 404
䡵 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . 405
䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 405
. . . . . . . . . . . . . . . . . . . . . . . . . 406

▫ Engine Oil

▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 408
▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . 409
▫ Maintenance-Free Battery . . . . . . . . . . . . . . 409
▫ Air Conditioner Maintenance . . . . . . . . . . . . 410
▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . 411
▫ Windshield Wiper Blades . . . . . . . . . . . . . . . 412
▫ Adding Washer Fluid . . . . . . . . . . . . . . . . . 412
▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 413
▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 416

400 MAINTAINING YOUR VEHICLE

▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 421
▫ Automatic Transmission — If Equipped . . . . 423
▫ Hydraulic Clutch Fluid — Manual

Transmission . . . . . . . . . . . . . . . . . . . . . . . 426
▫ Manual Transmission — If Equipped . . . . . . 426
▫ Transfer Case — If Equipped . . . . . . . . . . . . 426
▫ Front/Rear Axle Fluid . . . . . . . . . . . . . . . . . 427
▫ Maintenance After Off-Road Driving . . . . . . 428
▫ Appearance Care And Protection From

Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . 428
䡵 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
▫ Totally Integrated Power Module . . . . . . . . . 436
䡵 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . 442
䡵 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . 443

䡵 Bulb Replacement

. . . . . . . . . . . . . . . . . . . . . 444
▫ Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . 444
▫ Front Park/Turn Signal . . . . . . . . . . . . . . . . 445
▫ Front Side Marker . . . . . . . . . . . . . . . . . . . . 445
▫ Front Fog Lamp . . . . . . . . . . . . . . . . . . . . . 445
▫ Rear Tail, Stop, Turn Signal, And Backup

Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446

▫ Center High-Mounted Stop Lamp

(CHMSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 446
䡵 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . 447
䡵 Fluids, Lubricants And Genuine Parts . . . . . . . 448
▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448
▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . 449

ENGINE COMPARTMENT – 3.8L

MAINTAINING YOUR VEHICLE 401

1 — Integrated Power Module 2 — Battery 3 — Automatic Transmission Dipstick 4 — Engine Oil Fill 5 — Engine Oil Dipstick 6 — Brake Fluid Reservoir

7 — Washer Fluid Reservoir 8 — Engine Coolant Reservoir 9 — Air Cleaner Filter 10 — Coolant Pressure Cap 11 — Power Steering Fluid Reservoir

402 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations. If any of these systems require service, the OBD II system will turn on the “Malfunction Indicator Light (MIL).” It will also store diagnostic codes and other information to assist your service technician in making repairs. Al- though your vehicle will usually be drivable and not need towing, see your authorized dealer for service as soon as possible.

CAUTION!

• Prolonged driving with the MIL on could cause further damage to the emission control system. It could also affect fuel economy and drivability. The vehicle must be serviced before any emissions tests can be performed. • If the MIL is flashing while the engine is running, severe catalytic converter damage and power loss will soon occur. Immediate service is required.

Loose Fuel Filler Cap Message After fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is possibly loose, improp- erly installed, or damaged. A “gASCAP” message will be displayed in the odometer. Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists,

the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the prob- lem is detected twice in a row, the system will turn on the MIL. Resolving the problem will turn the MIL off.

EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration.

For states that require an Inspection and Mainte- nance (I/M), this check verifies the “Malfunction Indicator Light (MIL)” is functioning and is not on when the engine is running, and that the OBD II system is ready for testing. Normally, the OBD II system will be ready. The OBD II system may not be ready if your vehicle was recently

MAINTAINING YOUR VEHICLE 403
serviced, recently had a dead battery or a battery replace- ment. If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test. Your vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station. To check if your vehicle’s OBD II system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. 2. Turn the ignition switch to the ON position, but do not crank or start the engine. 3. If you crank or start the engine, you will have to start this test over. 4. As soon as you turn the ignition switch to the ON position, you will see the MIL symbol come on as part of a normal bulb check.

404 MAINTAINING YOUR VEHICLE 5. Approximately 15 seconds later, one of two things will happen:

a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is ready and you can proceed to the I/M station.

If your OBD II system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update. A recheck with the above test routine may then indicate that the system is now ready.

Regardless of whether your vehicle’s OBD II system is ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL is on with the engine running.

REPLACEMENT PARTS Use of genuine MOPAR威 parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance. Damage or failures caused by the use of non-MOPAR威 parts for maintenance and repairs will not be covered by the manufacturer’s warranty.

DEALER SERVICE Your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. Intentional tampering with emissions control NOTE: systems may void your warranty and could result in civil penalties being assessed against you.

WARNING!

You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.

MAINTAINING YOUR VEHICLE 405

MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require servicing or replacement in the future.

CAUTION!

• Failure to properly maintain your vehicle or per- form repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle perfor- mance. Immediately have potential malfunctions examined by an authorized Chrysler LLC dealer- ship or qualified repair center.

(Continued)

406 MAINTAINING YOUR VEHICLE

CAUTION! (Continued)

• Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air condi- tioning. Such damage is not covered by the New Vehicle Limited Warranty. If a flush is needed because of component malfunction, use only the specified fluid for the flushing procedure.

Engine Oil Checking Oil Level To assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Always maintain the oil level within the SAFE zone on the dipstick. Adding 1 U.S. Quart (0.95L) of oil when the reading is at the bottom of the SAFE zone will result in a reading at the top of the safe zone on these engines.

CAUTION!

Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine.

Change Engine Oil The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “Maintenance Schedule” in Section 8 for information on this system. NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichever occurs first.

Engine Oil Selection For best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends engine oils that are API Cer- tified and meet the requirements of Chrysler Material Standard MS-6395.

MAINTAINING YOUR VEHICLE 407

American Petroleum Institute (API) Engine Oil Identification Symbol

This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils.

CAUTION!

Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty.

408 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compart- ment” in this section. Lubricants which do not have both, the engine oil certi- fication mark and the correct SAE viscosity grade num- ber, should not be used. Synthetic Engine Oils Synthetic engine oils can be used if the recommended oil quality requirements are met, and the recommended maintenance intervals for oil and filter changes are followed.

Materials Added to Engine Oils The manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to engine oil. Engine oil is an engineered product and its performance may be impaired by supplemental additives. Disposing of Used Engine Oil and Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment. Contact your authorized dealer, service station, or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change.

MAINTAINING YOUR VEHICLE 409

Engine Oil Filter Selection All of the manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replace- ment. The quality of replacement filters varies consider- ably. Only high quality filters should be used to assure most efficient service. MOPAR威 engine oil filters are high quality oil filters and are recommended. Engine Air Cleaner Filter Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals.

Engine Air Cleaner Filter Selection The quality of replacement engine air cleaner filters varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR威 engine air cleaner filters are a high quality filter and are recommended. Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required.

WARNING!

WARNING!

The air cleaner can provide protection in the case of engine backfire. Do not remove the air cleaner unless it is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed. Failure to do so can result in serious personal injury.

Battery posts, terminals, and related accessories con- tain lead and lead compounds. Always wash hands after handling the battery.

410 MAINTAINING YOUR VEHICLE

CAUTION!

It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and are identified on the battery case. Also, if a “fast charger” is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery. Do not use a “fast charger” to provide starting voltage.

Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time.

CAUTION!

Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the New Vehicle Limited Warranty.

WARNING!

• Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information Book for further warranty information. • The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced repairman.

NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compres- sor Oil, and Refrigerants.

MAINTAINING YOUR VEHICLE 411

Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluoro- carbon (HFC) that is endorsed by the Environmental Protection Agency (EPA) and is an ozone-saving product. However, the manufacturer recommends that air condi- tioning service be performed by authorized dealers or other service facilities using recovery and recycling equipment. Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubri- cated periodically with a lithium-based grease, such as MOPAR威 Spray White Lube or equivalent, to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating, excess oil and grease should be removed. Particular attention should also be given to

412 MAINTAINING YOUR VEHICLE hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring. Apply a small amount of a high quality lubricant, such as MOPAR威 Lock Cylinder Lubricant or equivalent, directly into the lock cylinder. Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non-abrasive cleaner. This will remove accumula- tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to

remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. NOTE: Life expectancy of wiper blades varies depend- ing on geographical area and frequency of use. Poor performance of blades may be present with chattering, marks, water lines or wet spots. If any condition is present please proceed to clean wiper blades with humid cloth removing any debris that may be affecting its function. Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer (if equipped) is shared. The fluid reservoir is located in the engine compartment. Be sure to check the fluid level at regular intervals. Fill the reservoir with windshield washer solvent only (not radiator anti- freeze). When refilling the washer fluid reservoir, take

some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades; this will help blade perfor- mance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers.

WARNING!

Commercial windshield washer solvents are flam- mable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.

MAINTAINING YOUR VEHICLE 413

Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubri- cation or oil change. Replace as required.

414 MAINTAINING YOUR VEHICLE

CAUTION!

CAUTION!

The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effective- ness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine.

Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.

Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and vehicle.

WARNING!

A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.

In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn off the engine and allow it to cool. Service, including a tune up to manufacturer’s specifica- tions, should be obtained immediately. To minimize the possibility of catalytic converter dam- age:

MAINTAINING YOUR VEHICLE 415

vehicle.

• Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing. • Do not idle the engine for prolonged periods during very rough idle or malfunctioning operating condi- tions.

• Do not allow the vehicle to run out of fuel. NOTE: systems can result against you.

Intentional tampering with emissions control in civil penalties being assessed

416 MAINTAINING YOUR VEHICLE Cooling System

WARNING!

You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot.

Engine Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh engine coolant (anti- freeze). Check the front of the A/C condenser (if

equipped) or radiator for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the A/C con- denser (if equipped) or the back of the radiator core. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect the entire system for leaks. With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of engine coolant (antifreeze) from the radiator drain cock. If the cap is sealing properly, the engine coolant (anti- freeze) will begin to drain from the coolant recovery bottle. DO NOT REMOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT.

Cooling System — Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze). Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals. Selection Of Engine Coolant Use only the manufacturer’s recommended engine cool- ant (antifreeze). Refer to “Fluids, Lubricants, and Genu- ine Parts” in this section for the correct fluid type.

MAINTAINING YOUR VEHICLE 417

CAUTION!

• Mixing of engine coolant (antifreeze) other than the specified HOAT engine coolant (antifreeze) may result in engine damage and may decrease corrosion protection. If a non-HOAT engine cool- ant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible. • Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use addi- tional rust inhibitors or antirust products, as they may not be compatible with the antifreeze/engine coolant (antifreeze) and may plug the radiator.

(Continued)

418 MAINTAINING YOUR VEHICLE

CAUTION! (Continued)

• This vehicle has not been designed for use with Propylene Glycol based engine coolant (anti- freeze). Use of Propylene Glycol base engine cool- ant (antifreeze) is not recommended.

Adding Engine Coolant Your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to 5 Years or 102,000 miles (170 000 km) before replace- ment. To prevent reducing this extended maintenance period, it is important that you use the same engine coolant (antifreeze) throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze).

When adding engine coolant (antifreeze): • The manufacturer

recommends using MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. • Mix a minimum solution of 50% HOAT engine coolant (antifreeze) and distilled water. Use higher concentra- tions (not to exceed 70%) if temperatures below -34°F (-37°C) are anticipated. • Use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system.

Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated.

NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent engine coolant (antifreeze) changes. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant reserve tank. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.

MAINTAINING YOUR VEHICLE 419

WARNING!

The warning words DO NOT OPEN HOT on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the en- gine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.

Disposal of Used Engine Coolant Used ethylene glycol based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by ani- mals or children, do not store ethylene glycol based engine coolant (antifreeze) in open containers or allow it

420 MAINTAINING YOUR VEHICLE to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. Engine Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling, and warm to normal operating tempera- ture, the level of the engine coolant (antifreeze) in the bottle should be between the ranges indicated on the bottle. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing en- gine coolant (antifreeze). Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month.

When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is nor- mally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot engine coolant (antifreeze) to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant bottle. • Check the engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottle. If

engine coolant (antifreeze) needs to be added, the contents of the coolant recovery bottle must also be protected against freezing. • If frequent engine coolant (antifreeze) additions are required, or if the level in the recovery bottle does not drop when the engine cools, the cooling system should be pressure-tested for leaks. • Maintain the engine coolant (antifreeze) concentration at 50% HOAT engine coolant (antifreeze) (minimum) and distilled water for proper corrosion protection of your engine which contains aluminum components. • Make sure that the radiator and coolant recovery • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean.

bottle hoses are not kinked or obstructed.

MAINTAINING YOUR VEHICLE 421

• Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions.

Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals.

WARNING!

Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency.

422 MAINTAINING YOUR VEHICLE Power Disc Brakes Disc brakes do not require adjustment; however, several hard stops during the break-in period are recommended to seat the linings and wear off any foreign material. Brake Master Cylinder The fluid level in the master cylinders should be checked whenever the vehicle is serviced. If necessary, add fluid to bring level to the full level mark on the side of the reservoir of the brake master cylinder. With disc brakes, fluid level can be expected to fall as the brake pads wear. If the brake fluid level is abnormally low, check system for leaks. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.

WARNING!

• Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Using the wrong type of brake fluid can severely damage your brake system and/or impair its per- formance. The proper type of brake fluid for your vehicle is also labeled on the original factory installed hydraulic master cylinder reservoir.

(Continued)

WARNING! (Continued)

• To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a accident. • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts, causing the brake fluid to catch fire. Brake fluid can also damage painted and vinyl surfaces, care should be taken to avoid its contact with these surfaces.

(Continued)

MAINTAINING YOUR VEHICLE 423

WARNING! (Continued)

• Do not allow petroleum based fluid to contami- nate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in an accident.

Automatic Transmission — If Equipped

Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only manufacturer’s recommended transmis- sion fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid.

424 MAINTAINING YOUR VEHICLE

CAUTION!

Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” in this sec- tion for the correct fluid type.

Fluid Level Check — 42RLE Check the fluid level while the transmission is at normal operating temperature 180° F (82° C). This occurs after at least 15 miles (25 km) of driving. At normal operating temperature, the fluid cannot be held comfortably be- tween the fingertips. If the transmission overheats, a “HOTOIL” message will be displayed in the odometer and a chime will sound.

To properly check the automatic transmission fluid level, the following procedure must be used: 1. Operate the engine at idle speed and normal operating temperature. 2. The vehicle must be on level ground. 3. Fully apply the parking brake. 4. Place the shift lever momentarily into each gear posi- tion ending with the shift lever in PARK. 5. Remove the dipstick, wipe it clean and reinsert it until seated. 6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the HOT (upper) reference holes on the dipstick at normal operat- ing temperature. Verify that a solid coating of oil is seen on both sides of the dipstick. If the fluid is low, add as required into the dipstick tube. Do not overfill. After

adding any quantity of oil through the dipstick tube, wait a minimum of two minutes for the oil to fully drain into the transmission before rechecking the fluid level. If it is necessary to check the transmission below NOTE: the operating temperature, the fluid level should be between the two cold (lower) holes on the dipstick with the fluid at approximately 70° F (21° C) (room tempera- ture). If the fluid level is correctly established at room temperature, it should be between the HOT (upper) reference holes when the transmission reaches 180° F (21° C). Remember it is best to check the level at the normal operating temperature.

CAUTION!

Be aware that if the fluid temperature is below 50° F (10° C), it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading.

MAINTAINING YOUR VEHICLE 425

7. Check for leaks. Release the parking brake. NOTE: To prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is properly reseated. It is normal for the dipstick cap to spring back slightly from its fully seated position, as long as its seal remains engaged in the dipstick tube. Special Additives Automatic Transmission Fluid (ATF) is an engineered product and its performance may be impaired by supple- mental additives. Therefore, do not add any fluid addi- tives to the transmission. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks. In addition, avoid using transmission sealers as they may adversely affect seals.

426 MAINTAINING YOUR VEHICLE

CAUTION!

Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the New Vehicle Limited Warranty.

Hydraulic Clutch Fluid — Manual Transmission The clutch hydraulic system is a sealed maintenance-free system. In the event of leakage or other malfunction, the system must be replaced. Manual Transmission — If Equipped

Selection of Lubricant Use only manufacturer’s recommended manual trans- mission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.

Fluid Level Check Check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more than 3/16 in (4.76 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. Frequency of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the lubricant has become contaminated with water. If con- taminated with water, the fluid should be changed immediately. Transfer Case — If Equipped

Fluid Level Check The fluid level should be to the bottom edge of the fill hole (A) when the vehicle is in a level position.

MAINTAINING YOUR VEHICLE 427

CAUTION!

When replacing the plugs, do not overtighten them. You could damage them and cause them to leak.

Selection of Lubricant Use only manufacturer’s recommended fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Front/Rear Axle Fluid

Fluid Level Check Lubricant should be at the bottom edge of the oil fill hole. Adding Fluid Add lubricant only at the fill hole and only to the level specified above.

Adding Fluid Fluid should be added only at filler hole until fluid begins to run out of the hole. Drain First remove the fill plug (B), then the drain plug (C). The recommended tightening torque for the drain and fill plugs is 15 to 25 ft lbs (20 to 34 N·m).

428 MAINTAINING YOUR VEHICLE Selection of Lubricant Use only manufacturer’s recommended fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Maintenance After Off-Road Driving After extended operation in mud, sand or water, or similar dirty conditions, have your brake drums, brake linings, and axle joints inspected and cleaned as soon as possible. This will prevent any abrasive material from causing excessive wear or unpredictable braking action. Following off-road usage, completely inspect the under- body of your vehicle. Check the tires, body structure, steering, suspension and exhaust system for damage. Check the threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering and sus- pension. Retighten, if required, to torque values specified in the Service Manual. Also check for accumulations of vegetation or brush that could become a fire hazard, or

conceal damage to fuel lines, brake hoses, axle pinion seals, and propeller shafts. Check the air conditioning drain tube on the lower dash wall in the engine compart- ment for mud or debris, and clean as required. A plugged tube will adversely affect air conditioning performance.

CAUTION!

frequent heavy-duty driving conditions, Under change all lubricants, and lubricate body compo- nents more often than in normal service to prevent excessive wear.

Appearance Care and Protection from Corrosion

Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly

corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar.

MAINTAINING YOUR VEHICLE 429

• Salt in the air near sea-coast localities. • Atmospheric fallout/industrial pollutants. • Bird droppings. Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using MOPAR威 Car Wash or equiva- lent, or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumu- lated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover or equivalent to remove. • Use a high quality cleaner wax, such as MOPAR威 Cleaner Wax or equivalent to remove road film, stains, and to protect your paint finish. Take care never to scratch the paint.

430 MAINTAINING YOUR VEHICLE

• Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.

CAUTION!

• Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.

Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.

• It is important that the drain holes in the lower edges of the doors, rocker panels and tailgate are kept clear and open. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as pos- sible. The cost of such repairs is considered the respon- sibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., assure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider installing mud or stone shields behind each wheel.

• Use MOPAR威 Touch-Up Paint or equivalent on scratches or chips as soon as possible. Your authorized dealer has touch-up paint to match the color of your vehicle.

Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome-plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use MOPAR威 Wheel Cleaner or equivalent, or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush or metal pol- ishes. Only MOPAR威 cleaners or equivalent are recom- mended. Do not use oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish.

MAINTAINING YOUR VEHICLE 431

with a clean, dry towel.

Stain Repel Fabric Cleaning Procedure — If Equipped Stain Repel seats may be cleaned in the following man- ner: • Remove as much of the stain as possible by blotting • Blot any remaining stain with a clean, damp towel. • For tough stains, apply MOPAR威 Total Clean or equivalent, or a mild soap solution to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue. • For grease stains, apply MOPAR威 Multi-Purpose Cleaner or equivalent to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue. • Do not use any harsh solvents or any other form of

protectants on Stain Repel products.

432 MAINTAINING YOUR VEHICLE Interior Care Use MOPAR威 Total Clean or equivalent to clean fabric upholstery and carpeting. Interior Trim should be cleaned starting with a damp cloth, a damp cloth with MOPAR威 Total Clean or equiva- lent, then MOPAR威 Spot & Stain Remover or equivalent if absolutely necessary. Do not use harsh cleaners or Armor All威. Use MOPAR威 Total Clean or equivalent to clean vinyl upholstery.

WARNING!

Do not use volatile solvents for cleaning purposes. Many are potentially flammable and, if used in closed areas, they may cause respiratory harm.

CAUTION!

When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface.

Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive-type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rearview mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror.

Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet, soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use MOPAR威 Total Clean or equivalent, a mild soap solution, or lukewarm water. Do not remove the belts from the vehicle to wash them.

MAINTAINING YOUR VEHICLE 433
Replace the belts if they appear frayed or worn or if the buckles do not work properly. Appearance Care for Fabric Top Models

CAUTION!

To maintain the appearance of your vehicle’s interior trim and top, follow these precautions: • Avoid leaving your vehicle unattended with the top down, as exposure to sun or rain may damage interior trim. • Do not use harsh cleaners or bleaching agents on top • Do not allow any vinyl cleaner to run down and dry • After cleaning your vehicle’s fabric top, always make

material, as damage may result.

on the paint, leaving a streak.

sure it is completely dry before lowering.

434 MAINTAINING YOUR VEHICLE

• Be especially careful when washing the windows by following the directions for “Care of Fabric Top Windows.”

WASHING — Use MOPAR威 Car Wash or equivalent, or mild soap suds, lukewarm water, and a brush with soft bristles. If extra cleaning is required, use MOPAR威 Con- vertible Cloth Top Cleaner or equivalent, or a mild foaming cleaner on the entire top, but support the top from underneath. RINSING — Be sure to remove all traces of cleaner by rinsing the top thoroughly with clean water. Remember to allow the top to dry before lowering it.

CAUTION!

Failure to follow these cautions may cause interior water damage, stains or mildew on the top material:

(Continued)

CAUTION! (Continued)

• Avoid high-pressure car washes, as they can dam- age the top material. Also, increased water pres- sure may force past the weather strips. • It is recommended that the top be free of water prior to opening it. Operating the top, opening a door or lowering a window while the top is wet may allow water to drip into the vehicle’s interior. • Use care when washing the vehicle, water pressure directed at the weather strip seals may cause water to leak into the vehicle’s interior. • Careless handling and storage of the removable roof panels may damage the seals, causing water to leak into the vehicle’s interior. • The front panel(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicle’s interior.

Care of Fabric Top Windows

CAUTION!

Your vehicle’s fabric top has pliable plastic windows which can be scratched unless special care is taken by following these directions:

1. Never use a dry cloth to remove dust. Instead, use a microfiber towel or soft cotton cloth moistened with cold or warm, clean water, and wipe across the window, not up and down. MOPAR威 Jeep Soft Glass Window Cleaner or equivalent will safely clean all plastic win- dows without scratching. It removes fine scratches to improve visibility and provides UV protection to help prevent yellowing. 2. When washing, never use hot water or anything stronger than a mild soap. Never use solvents such as alcohol or harsh cleaning agents.

MAINTAINING YOUR VEHICLE 435
3. Always rinse thoroughly with cold water, then wipe with a soft and slightly moist, clean cloth. 4. When removing frost, snow or ice, never use a scraper or de-icing chemicals. Use warm water only if you must clean the window quickly. 5. Debris (sand, mud/dirt, dust, or salt) from off-road driving will have a major impact on zipper operation. Even normal on-road driving and vehicle washing will eventually impact window zipper operation. To maintain ease of use of the window zippers, each window zipper should be cleaned and lubricated regularly. Use MO- PAR威 Soft Top Zipper Cleaner and Lubricant or equiva- lent to ease zipper operation. Before applying, make sure the zipper teeth are clear of sand, mud, and other materials. Clean both sides of the zipper, not just one side. Rinse both zipper halves with fresh water and allow to dry. Aggressively work the MOPAR威 Soft Top Zipper Cleaner and Lubricant or equivalent into the zipper teeth.

436 MAINTAINING YOUR VEHICLE If a stuck zipper slide is experienced, work the MOPAR威 Soft Top Zipper Cleaner and Lubricant or equivalent into the zipper slide. Several applications may be required before the zipper comes free. 6. Never paste stickers, gummed labels or any tape to the windows. Adhesives are hard to remove and may dam- age the windows.

FUSES

Totally Integrated Power Module The Totally Integrated Power Module (TIPM) is located in the engine compartment near the battery. This center contains cartridge fuses, mini fuses and relays. A label that identifies each component is printed on the inside of the cover.

Totally Integrated Power Module (TIPM)

Cavity Cartridge

Fuse

Mini Fuse

Description

J1
J2

J3

— 30 Amp Pink —

— Transfer Case Module

—

Cavity Cartridge

Cavity Cartridge

J4

J5

J6

J7

J8
J9

J10

Fuse 25 Amp Natural 25 Amp Natural 40 Amp Green

30 Amp Pink

— 40 Amp Green 30 Amp Pink

Mini Fuse

Description

Driver Door Node

Passenger Door Node

Anti-Lock Brake Sys- tem (ABS) Pump Feed/ESP Anti-Lock Brake Sys- tem (ABS) Valve Feed/ESP — PZEV Sec Motor Feed/Flex Fuel Headlamp Wash Relay/Manifold Tun- ing Valve

J11

J13

J14

J15

J17

J18

J19

J20

MAINTAINING YOUR VEHICLE 437

Mini Fuse

Description

Sway Bar

Ignition Off Draw (IOD) — Main EBL (Rear Window Defogger) Rear Blower

Starter Solenoid

Powertrain Control Module (PCM) Trans Range Radiator Fan

Front Wiper LO/HI

Fuse 30 Amp Pink 60 Amp Yellow 40 Amp Green 30 Amp Pink 40 Amp Green 20 Amp Blue

60 Amp Yellow 30 Amp Pink

438 MAINTAINING YOUR VEHICLE

Cavity Cartridge

Fuse 20 Amp Blue —

J21

J22
M1

M2

M3

M4
M5
M6

Mini Fuse

Description

Cavity Cartridge

Fuse

M7

M8

M9

M10

Front/Rear Washer

Spare Center High-Mounted Stop Light (CHMSL)/ Switch Stop Lamp Feed Relay Trailer Lighting (Stop) Frt/Rear Axle Locker Relay — — Power Outlet #1/Rain Sensor

15 Amp Blue

20 Amp Yellow 20 Amp Yellow — — 20 Amp Yellow

Mini Fuse 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow

Description

Power Outlet #2
(BATT/ACC SELECT) Front Heated Seat

Rear Heated Seat (If Equipped) Ignition Off Draw — Vehicle Entertainment System (IOD-VES), Satellite Digital Audio Receiver (SDARS), DVD, Hands-Free Module (HFM), RA- DIO, Antenna (ANT), Universal Garage Door Opener (UGDO), Vanity Lamp (VANITY LP)

Cavity Cartridge

Fuse

M11

M12

M13

M14

Mini Fuse 10 Amp Red

30 Amp Green 20 Amp Yellow

20 Amp Yellow

Description

(Ignition Off Draw) IOD-HVAC/ATC, MW SENSR, Under- hood Lamp (UH LMP) Amplifier (AMP)

Ignition Off Draw— Cabin Compartment Node (IOD-CCN), Wireless Control Module (WCM), SI- REN, Multifunction Control Switch (MUL- TIFCTN SW) Trailer Tow (Export Only)

MAINTAINING YOUR VEHICLE 439

Cavity Cartridge

Fuse

M15

Mini Fuse 20 Amp Yellow

Description

COL MOD, IR SNS, Heater Ventilation, Air Conditioning/ Automatic Tempera- ture Control (HVAC/ ATC), Rear View Mirror (RR VW MIR), Cabin Compartment Node (CCN), Transfer Case Switch (T-CASE SW), RUN/ST, Multi- Function Control Switch (MULTIFTCN SW), Tire Pressure Monitor (TPM), Glow Plug Module (GLW PLG MOD) — Export Diesel Only

440 MAINTAINING YOUR VEHICLE

Cavity Cartridge

Fuse

M16

M17

M18

M19

M20

M21

Mini Fuse 10 Amp Red 15 Amp Blue

15 Amp Blue

25 Amp Natural 15 Amp Blue

20 Amp Yellow

Description

Cavity Cartridge

Fuse

Occupant Restraint Controller (ORC) Left Tail/License/ Park Lamp (LT-TAIL/ LIC/PRK LMP) Right Tail/Park/Run Lamp (RT-TAIL/ PRK/RUN LMP) Auto Shut Down (ASD #1 and #2) Cabin Compartment Node Interior Light (CCN INT LIGHT), Switch Bank (SW BANK) Auto Shut Down (ASD #3)

M22

M23

M24

M25

M26
M27

M28

M29

Mini Fuse 10 Amp Red 10 Amp Red 25 Amp Natural 20 Amp Yellow

— 10 Amp Red 10 Amp Red —

Description

Right Horn (RT HORN (HI/LOW) Left Horn (LT HORN (HI/LOW) Rear Wiper (REAR WIPER) Fuel Pump (FUEL PUMP), Diesel Lift Pump (DSL LIFT PUMP) — Export Only — Ignition Switch Feed, Wireless Module PCM Feed/TCM

—

MAINTAINING YOUR VEHICLE 441

Cavity Cartridge

Fuse

M30

M31

M32

M33

Mini Fuse 15 Amp Blue 20 Amp Yellow 10 Amp Red

10 Amp Red

Description

Wiper Motor Frt, J1962 Diagnostic Feed Backup Lamps (B/U LAMPS) Occupant Restraint Controller (ORC), TT EUROPE Next Generation Con- troller (NGC), Global Powertrain Engine Controller (GPEC)

Cavity Cartridge

Fuse

M34

Mini Fuse 10 Amp Red

M35

M36

M37

10 Amp Red 20 Amp Yellow 10 Amp Red

Description

Park Assist (PRK ASST), Heater Venti- lation, Air Condition- ing Module (HVAC MOD), Headlamp Wash (HDLP WASH), Compass (COMPAS) Heated Mirrors

Power Outlet

Anti-Lock Brake Sys- tem (ABS), Electronic Stability Program (ESP), Stop Lamp Switch (STP LP SW), Fuel Pump Rly Hi Control

442 MAINTAINING YOUR VEHICLE

Cavity Cartridge

Fuse

M38

Mini Fuse 25 Amp Natural

Description

Lock/Unlock Motors (LOCK/UNLOCK MTRS)

CAUTION!

• When installing the Integrated Power Module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in an electrical system failure.

(Continued)

CAUTION! (Continued)

• When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected.

VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take steps to protect your battery. You may: • Remove Cartridge fuse #15 in the Power Distribution • Store the removed IOD fuse in the Power Distribution

Center labeled Ignition-Off Draw (IOD).

Center location #11 labeled “IOD Storage.”

• Or, disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.

REPLACEMENT BULBS

Bulb Type Interior Lights Auto. Trans. Indicator Lamp. . . . . . . . . . . . . . . . . 658
Heater Control Lamps (2). . . . . . . . . . . . . . . . . . . 194
Rocker Switch Indicator Lamp (Rear Window Defogger, and Rear Wash/Wipe). . . . ** Soundbar Dome Lamp . . . . . . . . . . . . . . . . . . . . . 912
** Bulbs only available from authorized dealer.

MAINTAINING YOUR VEHICLE 443

Exterior Lights Bulb Type Backup Lamps (2) . . . . . . . . . . . . . . . . . . . . . . . 3157
Center High-Mounted Stop Lamp (1). . . . . . . . . L.E.D. Fog Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9145
Front Park/Turn Signal Lamps (2) . . . . . . . . . . . . 3157
Front Side Marker Lamps (2) . . . . . . . . . . . . . . . . 168
Headlamps (2) . . . . . . . . . . . . . . . . . . . . . . . . . . H13
Rear Stop/Tail/Turn Lamps (2) . . . . . . . . . . . . . . 3157
License Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
NOTE: Numbers refer to commercial bulb types that can be purchased from your local authorized dealer. If a bulb needs to be replaced, visit your authorized dealer or refer to the applicable Service Manual.

444 MAINTAINING YOUR VEHICLE BULB REPLACEMENT

NOTE: Lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamp

1. Open hood and support using prop rod. 2. Remove the front grille. Turn the retainers along the top 1/4 turn counterclockwise and remove. 3. Pull the bottom of the grille away starting at one side and working toward the other. 4. Turn both park and turn signal socket assemblies 1/4
turn counterclockwise and remove. 5. Remove the four screws holding the metal retaining ring.

6. Remove the lamp from the collar. 7. Grasp the bulb and turn 1/4 turn counterclockwise. 8. Pull the bulb from the housing. 9. Push connector locking tab to the unlock position. 10. Remove connector from bulb. 11. Push connector onto new bulb base, and push the connector locking tab to the lock position.

CAUTION!

Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.

12. Reinstall bulb housing. Rotate the bulb 1/4 turn clockwise.

Front Park/Turn Signal

Front Fog Lamp

MAINTAINING YOUR VEHICLE 445

1. Remove the front grille. Turn the retainers along the top 1/4 turn counterclockwise and remove. 2. Pull the bottom of the grille away starting at one side and working toward the other. 3. Turn the socket assembly 1/4 turn counterclockwise and remove from housing. Pull the bulb straight from the socket to replace. Front Side Marker

1. Reach under the front fender flare and locate the front side marker socket. 2. Turn the socket assembly counterclockwise 1/3 turn and remove it from the housing. Pull the bulb straight from the socket to replace.

1. Locate the front fog lamp in the front fascia, and disconnect the electrical connector from underneath. 2. Turn the bulb 1/4 turn counterclockwise.

CAUTION!

Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.

446 MAINTAINING YOUR VEHICLE Rear Tail, Stop, Turn Signal, and Backup Lamp

1. Remove the two inboard screws attaching the tail light housing to the body. DO NOT REMOVE THE OUTER SCREWS AT ANY TIME.

2. Separate the housing from the body by pushing the lamp inboard while pulling the lamp away from the body.

3. Rotate the appropriate socket 1/4 turn counterclock- wise, then remove it from the housing. 4. Pull the bulb straight from the socket to replace. Center High-Mounted Stop Lamp (CHMSL) The stop lamp is mounted on a bracket that extends upward from the tailgate behind the spare tire. If service is needed, obtain the LED/Cover Assembly from your local authorized dealer. 1. Remove the spare tire. 2. Remove the four screws holding the lens/cover in place on the spare tire carrier. 3. Disconnect the wire harness from the back of the LED cover.

FLUID CAPACITIES

Fuel (Approximate) — Two Door Models Fuel (Approximate) — Four Door Models Engine Oil with Filter 3.8 Liter Engine Cooling System * 3.8 Liter Engine (MOPAR威 Antifreeze/Engine Coolant 5
Year/100,000 Mile Formula or equivalent) * Includes coolant recovery bottle filled to MAX level.

MAINTAINING YOUR VEHICLE 447

U.S.

18.5 Gallons 22.5 Gallons

6 Quarts

13 Quarts

Metric 70 Liters 85 Liters

5.7 Liters

12 Liters

448 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS

Engine Component Engine Coolant

Engine Oil

Engine Oil Filter Spark Plugs Fuel Selection

Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade. MOPAR威 Engine Oil Filter or equivalent. RE14PLP5 (Gap 0.050 in [1.27 mm]) 87 Octane

Chassis Component Automatic Transmission Manual Transmission

Transfer Case Axle Differential (Front) Axle Differential (Rear)

Brake Master Cylinder

Power Steering Reservoir

MAINTAINING YOUR VEHICLE 449

Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4 Automatic Transmission Fluid or equivalent. MOPAR威 Manual Transmission Lubricant or equivalent (meeting the re- quirements of Chrysler Material Standard MS-9224). MOPAR威 ATF+4 Automatic Transmission Fluid or equivalent. MOPAR威 Gear & Axle Lubricant (SAE 80W-90) (API GL-5) or equivalent. 226 RBI (Model 44) - MOPAR威 Gear & Axle Lubricant (SAE 80W-90) (API GL-5) or equivalent. For trailer towing, use MOPAR威 Synthetic Gear & Axle Lubricant (SAE 75W-140) or equivalent. Models equipped with Trac-Lok™ require an additive. MOPAR威 DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recom- mended brake fluids. MOPAR威 Power Steering Fluid +4, MOPAR威 ATF+4 Automatic Transmis- sion Fluid or equivalent.

MAINTENANCE SCHEDULES

CONTENTS

䡵 Emissions Control System Maintenance . . . . . . 452
䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 452

▫ Required Maintenance Intervals . . . . . . . . . . 454

M

452 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating conditions, such as dusty areas and very short trip driving. Inspection and service should also be done anytime a malfunction is suspected. NOTE: Maintenance, replacement or repair of the emis- sions control devices and systems on your vehicle may be performed by any automotive repair establishment or individual using any automotive part that has been certified pursuant to U.S. EPA or in the State of Califor- nia, California Air Resources Board regulations.

MAINTENANCE SCHEDULE The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. On Non-EVIC equipped vehicles, “CHAngE OIL” will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is neces- sary. Based on engine operation conditions the oil change indicator message will illuminate, this means that service is required for your vehicle. Have your vehicle serviced as soon as possible, within the next 500 miles (805 km). NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change even if the oil change indicator message is NOT illuminated.

vehicle off-road for an extended period of time.

• Change your engine oil more often if you drive your • Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, which- ever comes first.

Your dealer will reset the oil change indicator message after completing the scheduled oil change. If this sched- uled oil change is performed by someone other than your dealer, the message can be reset by referring to the steps described under “Odometer/Trip Odometer” in the “In- strument Cluster Description” section of this manual. At Each Stop for Fuel • Check the engine oil level about five minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accuracy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark.

• Check the windshield washer solvent and add if

MAINTENANCE SCHEDULES 453

required.

damage.

Once a Month • Check tire pressure and look for unusual wear or • Inspect the battery and clean and tighten the terminals • Check the fluid levels of coolant reservoir, brake master cylinder, power steering and transmission and add as needed. • Check all lights and other electrical items for correct

as required.

operation.

Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the required maintenance intervals.

454 MAINTENANCE SCHEDULES At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. • Check the manual transmission fluid level.

CAUTION!

Failure to perform the required maintenance items may result in damage to the vehicle.

6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

MAINTENANCE SCHEDULES 455

12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the

engine air cleaner filter, replace if necessary. ❏ Inspect the brake linings, replace if necessary. ❏ Inspect exhaust system. Perform the first inspection at 12,000 miles (20 000 km) or

12 months.

❏ Inspect the CV joints. Perform the first inspection at 12,000 miles (20 000 km) or

12 months.

❏ Inspect the front suspension, tie rod ends and boot seals; replace if necessary.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer