2007 Jeep Compass Owners Manual

▫ Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 357
▫ Tail Lights, Rear Turn Signals And Backup

Lights — Replacement . . . . . . . . . . . . . . . . . . 358
▫ License Lights . . . . . . . . . . . . . . . . . . . . . . . . 360
▫ Center High-Mounted Stoplight . . . . . . . . . . . 361

䡵 Fluids And Capacities . . . . . . . . . . . . . . . . . . . 362
䡵 Fluids, Lubricants And Genuine Parts . . . . . . . . 363

▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363
▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364

MAINTAINING YOUR VEHICLE 315

316 MAINTAINING YOUR VEHICLE

ENGINE COMPARTMENT — GASOLINE ENGINES

ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations. If any of these systems require service, the OBD II system will turn on the “Malfunction Indicator Light.” It will also store diagnostic codes and other information to assist your service technician in making repairs. Al- though your vehicle will usually be drivable and not need towing, see your dealer for service as soon as possible.

MAINTAINING YOUR VEHICLE 317

CAUTION!

• Prolonged driving with the “Malfunction Indica- tor Light” on could cause further damage to the emission control system. It could also affect fuel economy and driveability. The vehicle must be serviced before any emissions tests can be per- formed. • If the “Malfunction Indicator Light” is flashing while the engine is running, severe catalytic con- verter damage and power loss will soon occur. Immediate service is required.

Loose Fuel Filler Cap Message After fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is loose or improperly installed. A GASCAP message will be displayed in the instrument cluster. Tighten the gas cap until a ⬙clicking⬙

318 MAINTAINING YOUR VEHICLE

sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off.

EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration.

For states, which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp)

is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing. Normally, the OBD system will be ready. The OBD system may not be ready if your vehicle was recently serviced, if you recently had a dead battery, or a battery replacement. If the OBD system should be determined not ready for the I/M test, your vehicle may fail the test. Your vehicle has a simple ignition key actuated test, which you can use prior to going to the test station. To check if your vehicle’s OBD system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. 2. Turn the ignition to the ON position, but do not crank or start the engine. 3. If you crank or start the engine, you will have to start this test over.

4. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 5. Approximately 15 seconds later, one of two things will happen:

a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station.

If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement,

MAINTAINING YOUR VEHICLE 319

you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that the system is now ready. Regardless of whether your vehicle’s OBD system is ready or not ready, if the MIL symbol is illuminated during normal vehicle operation, you should have your vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running.

REPLACEMENT PARTS Use of genuine Mopar威 parts for normal/scheduled maintenance and repairs is highly recommended to in- sure the designed performance. Damage or failures caused by the use of non-Mopar威 parts for maintenance and repairs will not be covered by the manufacturer’s warranty.

320 MAINTAINING YOUR VEHICLE

DEALER SERVICE Your dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: systems can result against you.

Intentional tampering with emissions control in civil penalties being assessed

WARNING!

You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.

MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance. However, if a malfunction of these items does occur, it could adversely affect the engine or vehicle performance. These items should be inspected if a malfunction is observed or suspected. Engine Oil

Checking Oil Level To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop.

The best time to check the engine oil level is about 5
minutes after a fully warmed engine is shut off. Do not check oil level before starting the engine after it has sat overnight. Checking engine oil level when the engine is cold will give you an incorrect reading.

Engine Oil Dipstick

MAINTAINING YOUR VEHICLE 321

Checking the oil while the vehicle is on level ground and only when the engine is hot, will improve the accuracy of the oil level readings. Maintain the oil level between the range markings on the dipstick. The range markings will consist of a crosshatch zone that says SAFE or a cross- hatch zone that says MIN at the low end of the range and MAX at the high end of the range. Adding one quart of oil when the reading is at the low end of the indicated range will result in the oil level at the full end of the indicator range.

CAUTION!

Do not overfill the engine. Overfilling the engine as indicated by the range markings, as described above, on the engine oil dipstick will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine.

322 MAINTAINING YOUR VEHICLE

Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to decide if any apply to you. • Day and night temperatures are below 32°F (0°C). • Stop and Go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high • Trailer towing. • Taxi, Police or delivery service (commercial service). • Off-Road or desert operation.

speeds during hot weather, above 90°F (32°C).

If ANY of these apply to you then change your NOTE: engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow schedule “B—All Engines” of the ⬙Maintenance Schedules⬙ section of this manual. If none of these apply to you, then change your engine oil at every interval shown on schedule “A” in the mainte- nance schedule section of this manual. NOTE: Under no circumstances should oil change in- tervals exceed 6000 miles (10 000 km) or 6 months whichever comes first. Engine Oil Selection (Gasoline Engines) For best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends engine oils that are API Cer- tified and meet the requirements of DaimlerChrysler Material Standard MS-6395.

American Petroleum Institute (API) Engine Oil Identification Symbol

This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils.

Engine Oil Viscosity (SAE Grade) SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low tempera- ture starting and vehicle fuel economy. Your engine oil filler cap also states the recommended engine oil vis- cosity grade for your engine.

MAINTAINING YOUR VEHICLE 323

Lubricants which do not have both, the engine oil certi- fication mark and the correct SAE viscosity grade num- ber should not be used. Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that are American Petroleum Institute (API) Certified and have the recom- mended SAE viscosity grade. Follow the maintenance schedule that describes your driving type. Materials Added To Engine Oils The manufacture strongly recommends against the addi- tion of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental ad- ditives.

324 MAINTAINING YOUR VEHICLE

Disposing of Used Engine Oil Care should be taken in disposing of used engine oil from your vehicle. Used oil, indiscriminately discarded, can present a problem to the environment. Contact your dealer, service station, or governmental agency for advice on how and where used oil can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection All of this manufacturers engines have a full-flow type disposable oil filter. Use a filter of this type for replace- ment. The quality of replacement filters varies consider- ably. Only high quality filters should be used to assure most efficient service. Mopar Engine Oil Filters are high quality oil filters and are recommended.

Drive Belt — Check Condition At the mileage shown in the maintenance schedules, check the drive belt for condition. Inspect the drive belt for evidence of cuts, cracks, or glazing and replace belt if any sign of damage which could result in belt failure. The belt is self-tensioning and will not need adjustment. Spark Plugs Spark plugs must fire properly to assure engine perfor- mance and emission control. New plugs should be in- stalled at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug. Refer to the Engine data Label located under the hood for the proper type of spark plug for use in your vehicle.

Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.

MAINTAINING YOUR VEHICLE 325

CAUTION!

Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.

326 MAINTAINING YOUR VEHICLE

WARNING!

A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn.

In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn off the engine and allow it to cool. Service, including a tune up to manufacturers specifica- tions, should be obtained immediately. To minimize the possibility of catalyst damage:

• Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the • Do not idle the engine with any spark plug wires

vehicle.

disconnected for prolonged period.

Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits. As vehicle mileage builds up, the PCV valve and passages may accumulate deposits. If a valve is not working properly, replace it with a new valve. DO NOT ATTEMPT TO CLEAN THE OLD PCV VALVE! Check ventilation hose for indication of damage or plugging deposits. Replace if necessary.

Fuel Filter A plugged fuel filter can cause hard starting or limit the speed at which a vehicle can be driven. Should an excessive amount of dirt accumulate in the fuel tank, frequent filter replacement may be necessary. The fuel filters are located inside the fuel tank. See your dealer for service. Air Cleaner Element (Filter) Under normal driving conditions, replace the filter at the intervals shown on Schedule “A”. If, however, you drive the vehicle frequently under dusty or severe conditions, the filter element should be inspected periodically and replaced if necessary at the intervals shown on Schedule “B”.

MAINTAINING YOUR VEHICLE 327

WARNING!

The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed. Failure to do so can result in serious personal injury.

Maintenance-Free Battery You will never have to add water, nor is periodic main- tenance required.

328 MAINTAINING YOUR VEHICLE

CAUTION!

WARNING!

When servicing the battery, always reinstall the battery thermowrap. The thermowrap provides bat- tery heat protection and will extend overall battery life. Failure to reinstall the thermowrap can result in evaporative loss of the battery fluid.

Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Don’t use a booster battery or any other booster source with an output greater than 12 volts. Don’t allow cable clamps to touch each other. Battery posts, terminals and related accessories con- tain lead and lead compounds. Wash hands after handling.

CAUTION!

It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening. If a “fast charger” is used while the battery is in the vehicle, disconnect both vehicle battery cables be- fore connecting the charger to battery. Do not use a “fast charger” to provide starting voltage as battery damage can result.

MAINTAINING YOUR VEHICLE 329

Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time.

330 MAINTAINING YOUR VEHICLE

WARNING!

• Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information. • The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced repairman.

Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment. NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compres- sor Oil, or Refrigerants. Power Steering — Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through a certified DaimlerChrysler Dealership.

WARNING!

Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid.

If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid types. Front Suspension Ball Joints There are two front suspension lower ball joints that are permanently lubricated. Inspect these ball joints when- ever under vehicle service is done. Damaged seals and their corresponding potentially damaged ball joints must be replaced.

MAINTAINING YOUR VEHICLE 331

Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the appli- cation of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching compo- nents to insure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant such as Mopar威 Lock Cylinder Lubricant directly into the lock cylinder.

332 MAINTAINING YOUR VEHICLE

Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non abrasive cleaner or use the washer solvent. This will remove accumulations of salt, waxes or road film and help reduce streaking and smearing. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield. make sure that they are not frozen to the glass before turning them on to avoid damaging the blade. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Windshield Wiper Blade Replacement 1. Lift the wiper arm away from the glass.

2. Push the release tab shown in the illustration and slide the wiper blade assembly down along the arm. Gently place the wiper arm on the windshield. 3. Install the new blade assembly onto the wiper arm tip until it locks in place. Windshield Washer Reservoir The washer fluid reservoir is located in the rear of the engine compartment on the right side and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze). Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system, or if exhaust fumes can be detected inside the vehicle, or

when the underside or rear of the vehicle is damaged; have a competent technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for an oil change or lubrication. Replace as required.

WARNING!

Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to Exhaust Gas in the Safety Tips section of this manual.

MAINTAINING YOUR VEHICLE 333

Cooling System

WARNING!

• When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot.

334 MAINTAINING YOUR VEHICLE

Coolant Checks Check engine coolant (antifreeze) protection every 12
months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the coolant recovery bottle tubing for brittle rub- ber, cracking, tears, cuts and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks.

Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old antifreeze solution. Selection Of Coolant Use only the manufacturers recommended coolant, refer to Fluids, Lubricants and Genuine Parts for correct coolant type.

CAUTION!

Mixing of coolants other than specified HOAT en- gine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT cool- ant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. Do not use plain water alone or alcohol base engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. This vehicle has not been designed for use with Propylene Glycol based coolants. Use of Propylene Glycol based coolants is not recommended.

MAINTAINING YOUR VEHICLE 335

Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles before replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same coolant throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Addi- tive Technology (HOAT) coolant. When adding coolant, a minimum solution of 50% rec- ommended Mopar Antifreeze/ Coolant 5 Year/100,000
Mile Formula HOAT (Hybrid Organic Additive Technol- ogy), or equivalent, in water should be used. Use higher concentrations (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C ) are anticipated. Use only high purity water such as distilled or deionized water when mixing the water/engine coolant solution.

336 MAINTAINING YOUR VEHICLE

The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing coolant types will decrease the life of the engine coolant and will require more frequent coolant changes. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.

WARNING!

• The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or engine damage may result.

Disposal of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children

do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine idling and warm to normal operating tempera- ture, the level of the coolant in the bottle should be between the “ADD” and “Full” lines, shown on the bottle. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for coolant freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month.

MAINTAINING YOUR VEHICLE 337

When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot coolant to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle.

338 MAINTAINING YOUR VEHICLE

• Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pres- sure tested for leaks. • Maintain coolant concentration at 50% HOAT engine coolant (minimum) and distilled water for proper corrosion protection of your engine which contains aluminum components. • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean, also.

• Do not change the thermostat for summer or winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions.

Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cracking, tears, cuts, abrasions, and exces- sive swelling indicate deterioration of the rubber Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold. Inspect hose rout- ing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear. Insure nylon tubing in these areas has not melted or collapsed

Inspect all hose connections such as clamps and cou- plings to make sure the are secure and no leaks are present. Components should be replaced immediately if there is any evidence of degradation that could cause failure. Fuel System Connections Electronic Fuel Injection high pressure fuel systems are designed with tubes and special connects, connections and clamps which have unique material characteristics to provide adequate sealing and resist attack by deterio- rated gasoline. You are urged to use only the manufactures-specified tubes, connections and clamps, or their equivalent in material and specification, in any fuel system servicing.

MAINTAINING YOUR VEHICLE 339

Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the Mainte- nance Section.

WARNING!

Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency.

Brake And Power Steering System Hoses When servicing the vehicle for scheduled maintenance, inspect the surface of the hoses and nylon tubing for evidence of heat and mechanical damage. Hard and

340 MAINTAINING YOUR VEHICLE

brittle rubber, cracking, tears, cuts, abrasions, and exces- sive swelling suggest deterioration of the rubber. Particu- lar attention should be made to examining those hose surfaces nearest to high heat sources, such as the exhaust manifold. Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. Insure nylon tubing in these areas has not melted or collapsed. NOTE: Often, fluids such as oil, power steering fluid, and brake fluid are used during assembly plant opera- tions to ease the assembly of hoses to couplings. There- fore, oil wetness at the hose-coupling area is not neces- sarily an indication of leakage. Actual dripping of hot fluid when systems are under pressure (during vehicle operation) should be noted before a hose is replaced based on leakage.

Inspection of brake hoses should be done when- NOTE: ever the brake system is serviced and at every engine oil change.

WARNING!

Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately.

Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning lamp is on. Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake

fluid reservoir. Fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. If your vehicle is equipped with a Manual NOTE: Transaxle , the Brake Fluid Reservoir supplies fluid to both the Brake System and the Clutch Release System. The two systems are separated in the reservoir and a leak in one system will not affect the other system. The Manual Transaxle Clutch Release System should not require fluid replacement during the life of the vehicle. If the Brake Fluid Reservoir is low, and the brake system does not indicate any leaks or other problems, it may be a result of a leak in the Hydraulic Clutch Release System. See your local authorized dealer for service. Use only manufacturers recommended brake fluid, refer to Fluids, Lubricants and Genuine Parts for correct fluid type.

MAINTAINING YOUR VEHICLE 341

WARNING!

Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard pro- longed braking. You could have an accident.

CAUTION!

Use of improper brake fluids will affect overall clutch system performance. Improper brake fluids may damage the clutch system resulting in loss of clutch function and the ability to shift the transaxle.

342 MAINTAINING YOUR VEHICLE

WARNING!

Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.

Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter. Do not allow petroleum based fluid to contaminate the brake fluid as seal damage will result! Automatic Transaxle (CVT)

Selection Of Lubricant It is important that the proper lubricant is used in the transaxle to assure optimum transaxle performance. Use only the manufacturer’s recommended transmission fluid which has been formulated with special metal to metal friction coefficient additives to provide the proper

steel belt traction on the drive and driven pulleys. Refer to Fluids, Lubricants and Genuine Parts for correct fluid type.

CAUTION!

Using a transmission fluid other than the manufac- turers recommended fluid will cause belt slip and result in a complete transmission failure! Refer to Fluids, Lubricants and Genuine Parts for correct fluid type.

Fluid Level Check The fluid level in the automatic transaxle should be checked only by a trained technician.

Fluid and Filter Changes Refer to the “Maintenance Schedule located if section 8 of this manual for the correct change interval for your type of driving. Special Additives Do not add any materials (other than leak detection dyes) to Automatic Transmission Fluid (ATF). ATF is an engi- neered product and its performance may be impaired by supplemental additives. Manual Transaxle

Lubricant Selection Use only manufacturers recommended transmission fluid. Refer to Fluids, Lubricants and Genuine Parts for correct fluid type.

MAINTAINING YOUR VEHICLE 343

Fluid Level Check Check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more that 3/16” (4.7 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. Frequency Of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the following conditions exist: • The lubricant has become contaminated with water. If contaminated with water, the fluid should be changed immediately. • If severe usage has occurred, refer to Maintenance

Schedule “B” in Section 8 of this manual.

344 MAINTAINING YOUR VEHICLE

Rear Drive Assembly (RDA )– AWD/4WD Models Only

Power Transfer Unit (PTU) – AWD/4WD Models Only

Lubricant Selection Use only manufacturers recommended fluid. Refer to Fluids, Lubricants and Genuine Parts for correct fluid type. Fluid Level Check Visually inspected the unit at each oil change for leakage. If leakage is detected, Check the fluid level by removing the fill plug. The fluid level should be maintained be- tween the bottom of the fill hole to 1/8 inch (4 mm) below the fill hole. Add fluid, if necessary, to maintain the proper level. Frequency Of Fluid Change Refer to the “Maintenance Schedule located if section 8 of this manual for the correct change interval for your type of driving.

Lubricant Selection Use only manufacturers recommended fluid. Refer to Fluids, Lubricants and Genuine Parts for correct fluid type. Fluid Level Check Visually inspected the unit at each oil change for leakage. If leakage is detected, Check the fluid level by removing the fill plug. The fluid level should be maintained be- tween the bottom of the fill hole to 1/8 inch (4 mm) below the fill hole. Add fluid, if necessary, to maintain the proper level. Frequency Of Fluid Change Refer to the “Maintenance Schedule located if section 8 of this manual for the correct change interval for your type of driving.

Appearance Care And Protection From Corrosion

Protection Of Body And Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.

MAINTAINING YOUR VEHICLE 345

The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near sea coast localities. • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using Mopar Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumu- lated on your vehicle, use Mopar Super Kleen Bug and Tar Remover to remove.

346 MAINTAINING YOUR VEHICLE

• Use Mopar Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.

CAUTION!

Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.

Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.

• It is important that the drain holes in the lower edges of the doors, rocker panels and trunk be kept clear and open. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as pos- sible. The cost of such repairs is considered the respon- sibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider

mud or stone shields behind each wheel.

• Use Mopar touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle.

Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use Mopar Wheel Cleaner or select a nonabra- sive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush or metal polishes. Only Mopar cleaners are recommended. Do not use oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. YES Essentials威 Fabric Cleaning Procedure – If Equipped YES Essentials威 seats may be cleaned in the following manner:

MAINTAINING YOUR VEHICLE 347

with a clean, dry towel.

• Remove as much of the stain as possible by blotting • Blot any remaining stain with a clean, damp towel. • For tough stains, apply Mopar威 Total Clean or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • For grease stains, apply Mopar威 Multi-purpose cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • Do not use any solvents or protectants on Yes Essen-

tials products.

Interior Care Use Mopar Total Clean to clean fabric upholstery and carpeting. Use Mopar Total Clean to clean vinyl upholstery.

348 MAINTAINING YOUR VEHICLE

Mopar Total Clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition.

WARNING!

Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.

Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses.

Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar Glass Cleaner or any commercial household- type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Instrument Panel Cover The instrument panel cover has a low glare surface which minimizes reflections in the windshield. Do not use protectants or other products which may cause undesir- able reflections. Use soap and warm water to restore the low glare surface.

MAINTAINING YOUR VEHICLE 349

Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them.

350 MAINTAINING YOUR VEHICLE

Replace the belts if they appear frayed or worn or if the buckles do not work properly. Dry with a soft tissue.

FUSES/INTEGRATED POWER MODULE (IPM) An Integrated Power Module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover. Refer to the graphic below for FUSES/IPM location.

Fuse and Relay Center (TIPM)

Cavity Cartridge

Fuse

Mini Fuse Empty 15 Amp Lt. Blue 10 Amp Red 10 Amp Red 20 Amp Yellow 10 Amp Red

30 Amp Green 30 Amp Green

Description

Empty 4WD ECU Feed

CHMSL Brake Switch Feed Ignition Switch Feed

Trailer Tow

IOD Sw/Pwr Mir/ Ocm Steering Cntrl Sdar/Hands Free Phone IOD Sense1

IOD Sense2

10

11

12

13

14

15

16

Cavity Cartridge

Fuse 40 Amp Green

40 Amp Green

MAINTAINING YOUR VEHICLE 351

Mini Fuse

20 Amp Yellow 15 Amp Lt Blue 20 Amp Yellow 20 Amp Yellow 10 Amp Red

15 Amp Lt. Blue

Description

Power Seats

CCN Power Locks

Power Outlet

Ign Run/Acc Inverter

Pwr run/Acc Outlet RR IOD CCN/ Interior Lighting RAD Fan Relay Bat- tery Feed IGN Run/Acc Cigar Ltr/Sunroof

352 MAINTAINING YOUR VEHICLE

Cavity Cartridge

Fuse

40 Amp Green

17

18

19

20

21

22

23

24

Mini Fuse 10 Amp Red

20 Amp Yellow 15 Amp Lt. Blue 10 Amp Red 10 Amp Red 15 Amp Lt. Blue 15 Amp Lt. Blue

Description

IOD Feed Mod-Wcm

ASD Relay Contact PWR Feed PWR Amp 1 & Amp 2 Feed IOD Feed Radio

IOD Feed Intrus Mod/Siren IGN RUN Heat/AC/ Compass Sensor ENG ASD Relay Feed Power Sunroof Feed

Cavity Cartridge

Fuse

25

26

27

28

29

30

31

32

30 Amp Pink

Mini Fuse 10 Amp Red 15 Amp Lt. Blue 10 Amp Red 10 Amp Red

20 Amp Yellow 10 Amp Red

Description

Heated Mirror

ENG ASD Relay Feed IGN RUN Only ORC Feed IGN RUN ORC/OCM Feed Hot Car (No Fuse Re- quired) Heated Seats

Headlamp Washer Relay Control ENG ASD Control Feed 1

Cavity Cartridge

Fuse

33

34

35

36

37

30 Amp Pink 40 Amp Green 30 Amp Pink

Mini Fuse 10 Amp Red

25 Amp Natural

Description

ABS MOD/J1962
Conn/PCM ABS Valve Feed

ABS Pump Feed

Headlamp /Washer Control / Smart Glass 110 Inverter

MAINTAINING YOUR VEHICLE 353

CAUTION!

• When installing the Integrated Power Module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in an electrical sys- tem failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse contin- ues to blow, it indicates a problem in the circuit that must be corrected.

354 MAINTAINING YOUR VEHICLE

Center labeled IOD (Ignition Off-Draw).

VEHICLE STORAGE If you will not be using your vehicle for more than 21
days you may want to take steps to preserve your battery. You may: • Disengage the mini fuse in the Power Distribution • Or, disconnect the negative cable from the battery. REPLACEMENT BULBS All the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not approved and should not be used for replacement.

LIGHT BULBS — Interior Bulb Number Front Header Lamp . . . . . . . . . . . . . . . . . . . . . . T578
Center Dome Lamp . . . . . . . . . . . . . . . . . . . . . . T578
Rear Cargo/Flashlight . . . . . . . . . . . . . . . . . 8–A35LF

LIGHTS BULBS — Outside Bulb No. Low Beam/High Beam Headlight . . . . . . . . . . . . H13
Front Park/Turn Signal/Side Marker Light . . . 3157AK Front Fog Light . . . . . . . . . . . . . . . . . . . . . . . . . 9145
Center High Mounted Stop Light (CHMSL) . . . . . . . . . . . . . . . . . . . . . . LED Assembly Rear Tail/Stop . . . . . . . . . . . . . . . . . . . . . . . . . . 3157
Rear Turn Signal . . . . . . . . . . . . . . . . . . . . . . 3157AK Backup Light . . . . . . . . . . . . . . . . . . . . . W16W (921) License Light . . . . . . . . . . . . . . . . . . . . . . . . . . W5W

BULB REPLACEMENT

Headlamps

• Raise the hood and locate connector behind the head-

MAINTAINING YOUR VEHICLE 355

lamp.

Locating Headlamp Connector

Releasing Red Lock Tab

356 MAINTAINING YOUR VEHICLE

• Reach into engine compartment and pull red lock out

at connector.

Remove green connector from back of bulb by pulling

straight back

Twisting Bulb From Socket

• Twist the bulb to the left and pull outward from

assembly.

NOTE: These are halogen bulbs. Take care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat buildup which reduces bulb life.

MAINTAINING YOUR VEHICLE 357

Fog Lights

Fog Light and Connector

1. Access lamp through the lower fascia cutout. 2. Rotate bulb and connector 1/4 turn counterclockwise. 3. Pull bulb off of connector.

Removing Halogen Bulb From Assembly

358 MAINTAINING YOUR VEHICLE

Tail Lights, Rear Turn Signals And Backup Lights — Replacement

1. Remove the two push-pins from the tail light housing.

Push-Pins Removed

Removing Push-Pins

2. Grasp the tail lamp and pull firmly to disengage the lamp from the aperture panel.

3. Twist and remove socket from lamp.

MAINTAINING YOUR VEHICLE 359

Pulling Lamp From Body

Removing Socket and Bulb

360 MAINTAINING YOUR VEHICLE

4. Remove bulb from socket and replace.

License Lights

1. Use a screw driver to gently pry against the side of the snap tab to remove the lamp from the liftgate.

Removing Bulb From Socket

Prying Lamp from Liftgate

2. Rotate the socket 1/4 turn counterclockwise.

MAINTAINING YOUR VEHICLE 361

Removing Socket from Lamp

3. Pull bulb from socket.

Removing Bulb From Socket

Center High-Mounted Stoplight Light is an LED assembly. See your authorized dealer for replacement.

362 MAINTAINING YOUR VEHICLE

FLUIDS AND CAPACITIES

Fuel (Approximate) Engine Oil-With Filter All Gasoline Engines (Use API Certified SAE 5W-20 Engine Oil.) Cooling System *

Mopar威 Antifreeze/Coolant 5 Year/100,000 Miles Formula), or

equivalent.

* Includes heater and coolant recovery bottle filled to MAX level.

U.S.

13.5 Gallons

4.5 Quarts

7.2 Quarts

Metric

51.0 Liters

4.26 Liters

6.8 Liters

MAINTAINING YOUR VEHICLE 363

FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant

Engine Oil

Engine Oil Filter Spark Plugs

Fuel Selection

Fluids, Lubricants and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent. Use API Certified SAE 5W-20 Engine Oil. Refer to your engine oil filler cap for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395. Mopar威 04884900AB or equivalent. Refer to the Vehicle Emission Control Information label in the engine com- partment. 87 Octane (R + M)/2

364 MAINTAINING YOUR VEHICLE

Chassis Component Automatic Transaxle Fluid Manual Transaxle Fluid Rear Drive Assembly (RDA)

Power Transfer Unit (PTU)

Brake Master Cylinder

Power Steering Reservoir

Fluids, Lubricants and Genuine Parts. Mopar威 CVTF + 4
Mopar威 ATF+4 MS9602
Mopar威 Gear & Axle Lubricant SAE 80W-90 API GL 5 or equivalent non- synthetic product. Mopar威 Gear & Axle Lubricant SAE 80W-90 API GL 5 or equivalent non- synthetic product. Mopar威 DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids or equivalent. Mopar威 Power Steering Fluid +4 or Mopar威ATF+4 Automatic Transmis- sion Fluid.

MAINTENANCE SCHEDULES

CONTENTS

䡵 Emission Control System Maintenance . . . . . . . . 366
䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 366

▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 369
▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . . 378

M

366 MAINTENANCE SCHEDULES

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating conditions such as dusty areas and very short trip driving. Inspection and service also should be done any time a malfunction is suspected. NOTE: Maintenance, replacement, or repair of the emis- sion control devices and systems on your vehicle may be performed by any automotive repair establishment or individual using any automotive part, which has been certified pursuant to U.S. EPA or, in the State of Califor- nia, California Air Resources Board regulations.

MAINTENANCE SCHEDULES There are two maintenance schedules that show the required service for your vehicle. First is Schedule “B”. It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high • Trailer towing. • Taxi, police, or delivery service (commercial service).

speeds during hot weather, above 90° F (32° C).

• Off-road or desert operation. • Heavy Loading If ANY of these apply to you then change your NOTE: engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. If ANY of these apply to you then change your NOTE: coolant every 102,000 miles (170 000 km) or 60 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. Second is Schedule “A”. It is for vehicles that are not operated under any of the conditions listed under Sched- ule ⬙B⬙. Use the schedule that best describes your driving condi- tions. Where time and mileage are listed, follow the interval that occurs first.

MAINTENANCE SCHEDULES 367

NOTE: Under no circumstances should oil change in- tervals exceed 6000 miles (10 000 km) or 6 months whichever comes first.

CAUTION!

Failure to perform the required maintenance items may result in damage to the vehicle.

At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark.

• Check the windshield washer solvent and add,

if

required.

M

368 MAINTENANCE SCHEDULES

damage.

Once a Month • Check tire pressure and look for unusual wear or • Inspect the battery and clean and tighten the terminals • Check the fluid levels of coolant reservoir, brake/ clutch master cylinder, and manual transaxle and add as needed. • Check all lights and all other electrical items for correct

as required.

operation.

At Each Oil Change • Change the engine oil filter. • Inspect the exhaust system. • Inspect the brake hoses.

sion components.

• Inspect the CV joints (if equipped) and front suspen- • Check the manual • Check the coolant level, hoses, and clamps.

transmission fluid level

equipped).

(if

CAUTION!

Do not check the automatic transaxle fluid. It must be check by a trained service technician every 15,000
miles and if required only the recommended fluid be added. Refer to the section “Fluids, Lubricants And Genuine Parts” for the proper fluid.

Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high • Trailer towing.

speeds during hot weather, above 90° F (32° C).

SCHEDULE “B” 369

• Taxi, police, or delivery service (commercial service). • Off-road or desert operation. • Heavy Loading If ANY of these apply to you then change your NOTE: engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. If ANY of these apply to you then change your NOTE: coolant every 102,000 miles (170 000 km) or 60 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual.

370 SCHEDULE “B”

Miles (Kilometers) Change engine oil and engine oil filter, or at 3
months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect engine air cleaner filter, replace if neces- sary.

3,000
(5 000 )

6,000

(10 000 )

9,000
(15 000)

12,000
(20 000)

15,000
(25 000)

SCHEDULE “B” 371

Miles (Kilometers) Change engine oil and engine oil filter, or at 3
months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Inspect auto tension drive belt and replace, if re- quired. Replace air cleaner filter. Replace spark plugs. Inspect PCV valve, replace as necessary.**

21,000
(35 000)

27,000
(45 000)

24,000
(40 000)

18,000
(30 000)

30,000
(50 000)

372 SCHEDULE “B”

Miles (Kilometers) Change engine oil and engine oil filter, or at 3
months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.

33,000
(55 000)

39, 000
(65 000)

42,000
(70 000)

36,000
(60 000)

45,000
(75 000)

48,000
(80 000)

Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Change Automatic Transaxle (CVT) Fluid and Filter Change Manual Transaxle Fluid. Change Rear Drive Assembly (RDA) fluid. Change Power Transfer Unit (PTU) fluid. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace, if required. Flush and replace engine coolant at 60 months, or 102,000 miles (170 000 km) whichever comes first.

51,000
(85 000)

54,000
(90 000)

SCHEDULE “B” 373

57,000
(95 000)

60,000
(100 000)

374 SCHEDULE “B”

Miles (Kilometers) Change engine oil and engine oil filter, or at 3
months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.

63,000
(105 000)

66,000
(110 000)

69,000
(115 000)

72,000
(120 000)

75,000
(125 000)

Miles (Kilometers ) Change engine oil and engine oil filter, or at 3
months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace, if re- quired.

78,000
(130 000)

81,000
(135 000)

84,000
(140 000)

87,000
(145 000)

90,000
(150 000)

SCHEDULE “B” 375