Download PDF Manual

tion switch with either side up. Wireless Ignition Node (WIN) The Wireless Ignition Node (WIN) operates similar to an ignition switch. It has four operating positions, three of which are detented and one spring-loaded. The detented positions are LOCK, ACC, and ON. The START position is a spring-loaded momentary contact position. When released from the START position, the switch automati- cally returns to the detented ON position.


Wireless Ignition Node (WIN)


Fob with Integrated Key (FOBIK) The Fob with Integrated Key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) trans- mitter and a valet key, which stores in the rear of the Fob. The valet key allows for entry into the vehicle should the battery in the vehicle or the Fob go dead. You can keep the valet key with you when valet parking. To remove the valet key from the Fob, slide the mechani- cal latch at the top of the Fob sideways with your thumb and then pull the key out of the Fob with your other hand.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15


3 Button FOBIK


NOTE: You can insert the double-sided valet key into the lock cylinders with either side up.


16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


Ignition Key Removal Place the selector lever in “P” (Park). Turn the key to the LOCK position, and remove the key. NOTE: † If you try to remove the key before you place the selector lever in “P” (Park), it may become trapped temporarily in the ignition switch. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition switch to warn you that this safety feature is inoperable. The engine can be started and stopped, but the key cannot be removed until you obtain service. † For vehicles equipped with the Electronic Vehicle Information Center the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 60 minutes


(EVIC),


after the ignition switch is turned to the LOCK posi- tion. Opening either front door will cancel this feature. The time for this feature is programmable. For details, refer to “Delay Power Off to Accessories Until Exit,” under “Personal Settings (Customer Programmable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual.


WARNING!


Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seri- ously or fatally injured. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.


CAUTION!


An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended.


Key-In-Ignition Reminder If you open the driver’s door and the key is in the ignition, a chime will sound to remind you to remove the key. The Key-In-Ignition reminder only sounds NOTE: when the ignition key is placed in the LOCK or ACC position.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17


SENTRY KEY The Sentry Key Immobilizer System prevents unautho- rized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses the factory-mated Fob with Integrated Key and Wireless Ignition Node (WIN) to prevent unau- thorized vehicle operation. Therefore, only Fobs that are programmed to the vehicle can be used to start and operate the vehicle. The system will shut the engine off in two (2) seconds if someone uses an invalid Fob to start the engine. After turning the ignition switch to the ON position, the Vehicle Security Alarm Indicator Light will turn on for three (3) seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to


18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


flash after the bulb check, it indicates that someone used an invalid Fob to start the engine. Either of these condi- tions will result in the engine being shut off after two (2) seconds. If the Vehicle Security Alarm Indicator Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle ser- viced as soon as possible. NOTE: † The Sentry Key Immobilizer System is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. † Exxon/Mobil Speed Pass,™ additional Fobs, or any other transponder-equipped components on the same key chain will not cause a fault unless the additional part is physically held against the Fob being used to


start the vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system. All of the Fobs provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys


NOTE: Only Fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Fob is programmed to a vehicle, it cannot be programmed to any other vehicle.


CAUTION!


Always remove Sentry Keys from the vehicle and lock all doors when leaving the vehicle unattended.


At the time of purchase, the original owner is provided with a four-digit PIN number. Keep the PIN in a secure


location. This number is required for dealer replacement of Fobs. Duplication of Fobs may be performed at an authorized dealer or by using the Customer Key Pro- gramming procedure. This procedure consists of pro- gramming a blank Fob to the vehicle electronics. A blank Fob is one, which has never been programmed. NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle Fobs with you to the dealer. Customer Key (Fob) Programming If you have two valid sentry keys, you can program new sentry keys to the system by performing the following procedure: 1. Insert the first valid key into the ignition switch and turn the ignition switch ON for at least 3 seconds but no longer than 15 seconds. Turn the ignition switch OFF and remove the first key.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19


2. Insert the second valid key and turn the ignition switch ON within 15 seconds. After ten seconds, a chime will sound and the Vehicle Security Alarm Indicator Light will begin to flash. Turn the ignition switch OFF and remove the second key. 3. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10
seconds, a single chime will sound and the Vehicle Security Alarm Indicator Light will stop flashing, turn on again for 3 seconds, and then turn off. The new Sentry Key is programmed. The Keyless Entry Transmitter will also be programmed during this pro- cedure. Repeat this procedure to program up to 8 keys. If you do not have a programmed sentry key, contact your dealer for details.


20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


If a programmed key is lost, see your dealer to NOTE: have all remaining keys erased from the systems memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be repro- grammed. All vehicle keys must be taken to the dealer at the time of service to be reprogrammed. General Information The Sentry Key system complies with FCC rules part 15
and with RSS-210 of Industry Canada. Operation is subject to the following conditions: † This device may not cause harmful interference. † This device must accept any interference that may be received, including interference that may cause undes- ired operation.


SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors, liftgate, liftgate flipper glass, and ignition for unauthorized operation and movement inside of the vehicle. When the alarm is activated, the system provides both audible and visual signals. The horn will sound repeatedly for three minutes and the headlights and taillights will flash for an addi- tional 15 minutes. To Set the Alarm The alarm will set when you use the remote keyless entry transmitter to lock the doors and liftgate or when you use the power door lock switch while the door is open. After all the doors are locked and closed, a red light (located in the instrument cluster) will flash rapidly for about 16
seconds to signal that the system is arming. During this 16 second pre-arm period, opening any door or the liftgate will cancel the arming. If the system successfully arms, the red light will flash at a slower rate to indicate the alarm is set. A manual lock of the doors, either with


the door lock plunger located on the inside of the doors or with the driver’s door key lock cylinder, will not set the alarm. To Disarm the System To disarm the system, use the remote keyless entry transmitter. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors. Check the vehicle for tampering. The Security Alarm System is designed to protect your vehicle; however, you can create conditions where the system will arm unexpectedly. If you remain in the vehicle and lock the doors with the transmitter, once the system is armed (after 16 seconds), when you pull the door handle to exit the alarm will sound. If this occurs, press the “Unlock” button on the remote keyless entry transmitter to disarm the system. The Security Alarm System will not disarm with a manual unlock, either


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21


through the lock plunger located on the inside of the door, or through a key in the driver’s door key cylinder.


ILLUMINATED ENTRY The interior lights come on when you open any door. They will remain on for about 30 seconds after all doors are closed then fade to off. The lights also will fade to off if you turn on the ignition after you close all the doors.


REMOTE KEYLESS ENTRY This system allows you to lock or unlock the doors, liftgate, or activate the panic alarm from distances up to about 23 feet (7 meters) using a hand held radio trans- mitter. The transmitter need not be pointed at the vehicle to activate the system.


22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


Inserting the Fob with Integrated Key into the NOTE: ignition switch disables all buttons on that transmitter; however, the buttons on the remaining transmitters will continue to work. Shifting the vehicle out of “P” (Park) disables all transmitter buttons for all Fobs.


3 Button FOBIK


To Unlock the Doors Press and release the UNLOCK button on the transmitter once to unlock the driver’s door, or twice to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Remote Key Unlock, Driver Door/All Doors First This feature lets you program the system to unlock either the driver’s door or all doors on the first press of the UNLOCK button on the transmitter. To change the cur- rent setting, proceed as follows: † For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Remote Key Unlock,” under “Personal Settings (Customer Pro- grammable Features),” under “Electronic Vehicle In- formation Center (EVIC)” in Section 4 of this manual for details.


Flash Lights with Remote Key Lock This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the transmitter. This feature can be turned on or off. To change the current setting, proceed as follows: † For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Flash Lights with Remote Key Lock,” under 9Personal Settings (Cus- tomer Programmable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual for details.


Turn Headlights On with Remote Key Unlock This feature activates the headlights for up to 90 seconds when the doors are unlocked with the transmitter. The time for this feature is programmable on vehicles equipped with the Electronic Vehicle Information Center (EVIC). For details, refer to “Turn Headlights On with


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23


Remote Key Unlock,” under “Personal Settings (Cus- tomer Programmable Features),” under “Electronic Ve- hicle Information Center (EVIC)” in Section 4 of this manual. To Lock the Doors Press and release the LOCK button on the transmitter to lock all doors. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Sound Horn with Remote Key Lock This feature will cause the horn to chirp when the doors are locked with the transmitter. This feature can be turned on or off. To change the current setting, proceed as follows: † For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Sound Horn with Remote Key Lock,” under “Personal Settings (Cus- tomer Programmable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual for details.


24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


To Release the Liftgate Flipper Glass Press the “Flipper Glass/Trunk Release” button on the transmitter two times to release the flipper glass.


WARNING!


Driving with the flipper glass open can allow poi- sonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle.


Using The Panic Alarm To turn the panic alarm feature ON or OFF, press and hold the PANIC button on the transmitter for at least one second and release. When the panic alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on.


The panic alarm will stay on for 3 minutes unless you turn it off by either pressing the PANIC button a second time or drive the vehicle at a speed of 15 mph (24 km/h) or greater. NOTE: † The interior lights will turn off if you turn the ignition switch to the ACC or ON position while the panic alarm is activated. However, the exterior lights and horn will remain on. † You may need to be less than 23 feet (7 meters) from the vehicle when using the transmitter to turn off the panic alarm due to the radio frequency noises emitted by the system.


Programming Additional Transmitters Refer to SENTRY KEY “Customer Key (Fob) Program- ming.” If you do not have a programmed transmitter, contact your dealer for details. Transmitter Battery Service The recommended replacement battery is one CR2032
battery. NOTE: Perchlorate Material — special handling may apply. www.dtsc.ca.gov/hazardouswaste/ perchlorate NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. Battery access is through a door located on the rear of the FOBIK. Insert a small, flat bladed screwdriver into the slot and gently pry open the access door.


See


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25


FOBIK Battery Replacement


2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. Reposition the access door panel over the battery opening and snap into place.


26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: † This device may not cause harmful interference. † This device must accept any interference received, including interference that may cause undesired op- eration.


NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. If your Remote Keyless Entry (RKE) transmitter fails to operate from a normal distance, check for these two conditions. 1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years.


2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.


REMOTE STARTING SYSTEM — IF EQUIPPED Your vehicle may be equipped with a remote starting system, which will allow the vehicle to be started up to 300 feet (91 meters) away from the vehicle using the remote keyless entry key fob which is part of your ignition key. In order to remote start your vehicle, the hood, liftgate, and all of the doors must be closed. To remote start your vehicle, press the “Remote Start” button on the key fob twice within three seconds. To indicate that the vehicle is about to start, the parking lights will flash and the horn will sound briefly (if programmed). To turn the horn on or off, refer to “Electronic Vehicle Information Center/Customer Pro- grammable Features/Sound Horn With Lock?” in Section 4 of this manual.


2


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27


To enter the vehicle while the engine is running during a remote start, you must first unlock the vehicle using the “Unlock” button on the key fob. After the vehicle is unlocked, you have 15 minutes to enter the vehicle, insert the key into the ignition, and move it to the RUN position. Otherwise, the engine will cancel remote start and automatically turn off. Remote start will also cancel if any of the following occur: † If the engine stalls or RPM exceeds 2500
† Any engine warning lamps come on † The hood is opened † The hazard switch is pressed † The transmission is moved out of P (Park). † The brake pedal is pressed.


Remote Start Button


Once the vehicle has started, the engine will run for 15
minutes. To cancel remote start, press the “Remote Start” button once. The parking lamps will remain illuminated to indicate that the vehicle has remote started and the engine is running. The lamps will turn off when the ignition is turned to RUN or the remote start is cancelled.


28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


The vehicle can be started remotely up to a maximum of two times. The vehicle is also allowed a maximum of one failed start, where the remote start sequence was initiated but the engine stopped cranking without starting. After either of these conditions, or if the Vehicle Theft Alarm is alarming, or if the PANIC button was pressed, the vehicle must be reset by inserting a valid key into the ignition and moving it to the RUN position, then back to LOCK.


DOOR LOCKS


Manual Door Locks Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door.


WARNING!


† For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. † When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe per- sonal injuries and death.


Power Door Locks The power door lock switch is located on each front door panel. Press the switch to lock or unlock the doors.


Power Door Lock Switch


If the plunger is down when the door is closed, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29


If you press the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors will not lock. The rear doors cannot be opened from inside the vehicle until you pull up the lock plungers. Automatic Door Locks lock If this feature is selected your door locks will automatically if the vehicle speed is above 15 mph (24
km/h) and all doors are closed. It will reset whenever a door is opened. This feature is selectable and can be turned on or off. Refer to “Electronic Vehicle Information Center (EVIC) — Customer Programmable Features” in Section 4 of this manual or see your authorized dealer.


30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


Automatic Unlock on Exit Feature — Only Available if Auto Lock is Enabled This feature will unlock all the doors when the driver’s door is opened if the vehicle is stopped and in P (Park) or N (Neutral). Refer to “Electronic Vehicle Information Center (EVIC) — Customer Programmable Features” in Section 4 of this manual or see your authorized dealer. Child Protection Door Lock The rear doors of your vehicle are equipped with child protection locks. If you push up on the lever on the open edge of the door it cannot be opened from the inside of the vehicle. Push the lever down to disengage the child protection locks.


WARNING!


Avoid trapping anyone in the vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.


Child Protection Door Lock


WINDOWS


Power Windows The power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSORY position.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31


Power Window Switches


The power window switches remain active for up to 10
minutes after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature.


32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


Auto Down Both the driver and front passenger window switch has an “Auto Down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the “Auto Down” movement, operate the switch in either the up or down direction and release the switch. To stop the window from going all the way down during the auto-down operation, pull up on the switch briefly. To open the window part way, press to the first detent and release it when you want the window to stop. The power window switches remain active for 10 min- utes after the ignition has been turned off. Opening either front door will cancel this feature.


Auto Up Feature with Anti-Pinch Protection (Driver’s and Front Passenger Door Only) Lift the window switch to the second detent, release, and the window will go up automatically. To stop the window from going all the way up during the auto-up operation, push down on the switch briefly. To close the window part way, lift the window switch to the first detent and release when you want the window to stop. If the window runs into any obstacle during the NOTE: auto-closure it will reverse direction and then stop. Remove the obstacle and use the window switch again to close the window. Any impact due to rough road condi- tions may trigger the auto reverse function unexpectedly during auto closure. If this happens pull the switch lightly to the first detent and hold to close the window manually.


WARNING!


There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing.


Resetting the Auto-Up Feature Should the Auto-Up feature stop working the window probably needs to be reset. To reset Auto-Up: Pull the window switch up and close the window com- pletely, then pull and hold the switch for 1 second. Window Lockout Switch The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lockout button. To enable the window controls, press the window lockout button again.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33


Wind Buffeting


Power Window Lock


Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain


34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting.


LIFTGATE To open the liftgate, pull up (squeeze) on the handle and lift. Manually unlocking the vehicle doors with the plunger or a key in the lock cylinder will not unlock the liftgate.


Liftgate Release


WARNING!


Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle.


Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate.


WARNING!


To avoid injury stand back when opening. Glass will automatically rise.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35


Once the liftgate flipper glass has been opened, connec- tion to the rear window wiper is interrupted, preventing activation of the rear wiper blade while the flipper glass is open.


WARNING!


Driving with the flipper glass open can allow poi- sonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle.


Liftgate Glass Release


36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the remote keyless entry transmitter. Press the button on the remote keyless entry transmitter twice within five seconds, to open the power liftgate. Once the liftgate is fully open, pressing the button twice within five seconds a second time will close the liftgate. Also, the power liftgate may be closed by pressing a button located in the upper left trim, in the liftgate opening. Pressing once will close the liftgate only. This button cannot be used to open the liftgate. When the remote keyless entry transmitter button is pressed two times and the “Lamp Flash” feature is enabled, the turn signals will flash twice to signal that the liftgate is opening or closing.


NOTE: † In the event of a power malfunction to the liftgate, an emergency liftgate latch release can be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the lift- gate trim panel.


WARNING!


During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away.


A beeping signal will sound two seconds before the liftgate starts to open or close.


NOTE: † If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically reverse to the closed or open position, provided it meets sufficient resistance. † There are also pinch sensors attached to the side of the liftgate. Light pressure anywhere along these strips will cause the liftgate to return to the open position. † The power liftgate must be in the full open position for any of the buttons to operate. If the liftgate is not fully open, press the remote keyless entry transmitter to fully open the liftgate and then press again to close. † If the liftgate handle is pulled while the power liftgate is closing, the liftgate will reverse to the full open position.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37


† If the liftgate handle is pulled while the power liftgate is opening, the liftgate motor will disengage to allow manual operation. † The power liftgate buttons will not operate if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h). † The power liftgate will not operate in temperatures below 222° F (230° C) or temperatures above 150° F (65° C). Be sure to remove any buildup of snow or ice from the liftgate before pressing any of the power liftgate switches. † If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually. † If your liftgate is power closing and you put the vehicle in gear, the liftgate will continue to power close. However, vehicle movement may result in a detection of an obstruction.


38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


WARNING!


† Driving with the liftgate open can allow poison- ous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. † If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode.


Gas props support the liftgate in the open position. However, because the gas pressure drops with tempera- ture, it may be necessary to assist the props when opening the liftgate in cold weather.


OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and right front passenger, and, window bags for the driver and passengers seated next to a window. If you will be carrying children too small for adult-size belts, your seat belts also can be used to hold infant and child restraint systems. NOTE: The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible.


WARNING!


In a collision, you and your passengers can suffer injuries, including fatalities, if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly.


Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision which includes you. This can happen far away from home or on your own street.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39


Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times to reduce or prevent injuries. Lap/Shoulder Belts All seating positions in your vehicle have combination lap/shoulder belts. The belt webbing retractor is de- signed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a colli- sion, the belt will lock and reduce the risk of you striking the inside of the vehicle or being thrown out.


Lap/Shoulder Belt Operating Instructions


1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap.


40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


WARNING!


† Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your pas- sengers safe, too. † Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41


3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.”


Latch Plate


Latch Plate To Buckle


42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


WARNING!


A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. A shoulder belt placed behind will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together.


4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.


WARNING!


A lap belt worn too high can increase the risk of injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdo- men. Always wear the lap part of your seat belt as low as possible and keep it snug. A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your authorized dealer and have it fixed.


5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt.


Removing Slack From Belt


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43


6. To release the belt, push the red button marked PRESS on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully.


WARNING!


A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.).


44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


Adjustable Upper Shoulder Belt Anchorage In the front seating positions, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Press the release button to release the anchorage, and then move it up or down to the position that serves you best.


As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Automatic Locking Mode — If Equipped In this mode, the shoulder belt is automatically pre- locked. The belt will still retract to remove any slack in the shoulder belt. When To Use The Automatic Locking Mode Anytime a child safety seat is installed in a second or third row seating position. Children 12 years old and under should be properly restrained in a rear seat when- ever possible.


Adjusting Upper Shoulder Belt


How To Use The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to Disengage The Automatic Locking Mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic lock- ing mode and activate the vehicle sensitive (emergency) locking mode.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45


Energy Management Feature This vehicle has a safety belt system with an energy man- agement feature in the front seating positions to help further reduce the risk of injury in the event of a head-on collision. This safety belt system has a retractor assembly that is designed to release webbing in a controlled manner. This feature is designed to help reduce the belt force acting on the occupant’s chest.


WARNING!


† The belt and retractor assembly must be replaced if the seat belt assembly “automatic locking retrac- tor” feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual. † Failure to replace the belt and retractor assembly


could increase the risk of injury in collisions.


46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


Seat Belt Pretensioners The driver and front passenger seat belts are equipped with a pretensioning device that is designed to remove any slack from the seat belt systems in the event of a collision. This device improves the performance of the seat belt by assuring that the belt is tight around the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints. NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt must still be worn snugly and positioned properly. The pretensioners are triggered by the Occupant Re- straint Control (ORC) Module. Like the front airbags, the pretensioners are a single use item. After a collision that is severe enough to deploy the airbags and pretensioners, they must be replaced.


Enhanced Seat Belt Use Reminder System (BeltAlert) If the driver’s seat belt has not been buckled within 60
seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts. Once the warning is triggered, the Enhanced Warning System (BeltAlert) will continue to chime and flash the Seat Belt Warning Light for 96
seconds or until the driver’s seat belt is buckled. The Enhanced Warning System (BeltAlert) will be reactivated if the driver’s seat belt is unbuckled for more than 10
seconds and the vehicle speed is greater than 5 mph (8
km/h). The Enhanced Warning System (BeltAlert) can be en- abled or disabled by your authorized dealer or by following these steps:


NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. The manufacturer does not recom- mend deactivating the Enhanced Warning System (BeltAlert). 1. Turn the ignition switch to the OFF position, and buckle the driver’s seat belt. 2. Turn the ignition key to the ACCESSORY/RUN posi- tion (engine does not need to be running), and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times with 10 seconds, ending with the seat belt buckled. 4. Turn the ignition key to the OFF position. A single chime will sound to signify that you have successfully completed the programming.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47


The Enhanced Warning System (BeltAlert) can be reacti- vated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s seat belt remains unfastened. Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.


48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the ex- tender and store it.


WARNING!


Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.


Driver And Front Passenger Supplemental Restraint Systems (SRS)


1 — Driver Airbag 2 — Passenger Airbag 3 — Knee Bolster


This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger side airbag is mounted in the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers. NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size. This vehicle is equipped with window bags to protect the driver, front, and rear passengers sitting next to a win- dow. They are located above the side windows. Their covers are also labeled SRS/AIRBAG.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49


Window Airbag Location


NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment.


50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


WARNING!


† Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. † Do not stack luggage or other cargo up high enough to block the location of the window bag. The area where the window bag is located should remain free from any obstructions. † Do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require permanent attachments (bolts or screws) for installation on the vehicle roof. Do not drill into the roof of the vehicle for any reason. † Do not cover or place items on the airbag covers. injury during


These items may cause serious inflation.


NOTE: Do not use a clothing bar mounted to the coat hooks in this vehicle. A clothing bar will impede the proper performance of the window bags. The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Along with the seat belts, front airbags work with the instrument panel knee bol- sters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions. The window bag on the crash side of the vehicle is triggered in moderate to severe side collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly.


Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years and under should always ride buckled up in a rear seat. Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger airbag. An airbag deployment could cause severe injury or death to infants in that position. Children that are not big enough to properly wear the vehicle seat belt should be secured in the rear seat, in a child restraint or belt-positioning booster seat. Older children who do not use child restraints or belt- positioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51


seat as far back as possible, and use the proper child restraint. See “Child Restraint” in this section. You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should use their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. Do not lean against the door or window, airbags will inflate forcefully into the space between you and the door. 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under “If You Need Assistance” in Section 9 of this manual.


52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


WARNING!


† Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. † Being too close to the steering wheel or instrument panel during airbag deployment could cause seri- ous injury. Airbags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. † Side curtain airbags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat.


Airbag System Components The airbag system consists of the following: † Occupant Restraint Control Module † Airbag Warning Light † Driver Airbag † Passenger Airbag † Side Curtain Airbags above Side Windows † Side Remote Acceleration Sensors † Driver Side Seat Track Position Sensor † Steering Wheel and Column † Instrument Panel † Interconnecting Wiring † Knee Impact Bolsters † Front Acceleration Sensors † Driver and Front Passenger Seat Belt Pretensioners


How The Airbag System Works † The Occupant Restraint Control (ORC) Module de- termines if a frontal, side, or rollover collision is severe enough to require the front and/or side airbags to inflate. The front airbag inflators are designed to provide different rates of airbag inflation from direc- tion provided by the ORC. The ORC will detect roll overs, not rear impacts. The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON positions. These include all of the items listed above except the knee bolster, the instru- ment panel, and the steering wheel and column. If the key is in the LOCK position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53


Also, the ORC turns on the “Airbag Warning Light” for 2.5 to 8 seconds for a self-check when the ignition is first turned on. After the self-check, the “Airbag Warning Light” will turn off. If the ORC detects a malfunction in any part of the system, it turns on the “Airbag Warning Light” either momentarily or continuously. A single chime will sound if the light comes on again after initial start up.


WARNING!


Ignoring the “Airbag Warning Light” in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.


54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


† The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel. When the ORC detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags. Different airbag inflation rates are possible, based on collision severity and occupant size. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50–70 milliseconds. This is about half of the time it takes to blink your eyes. The bags then quickly deflate while helping to restrain the driver and front passenger. The driver front airbag gas is vented through the vent holes in the sides of the airbag. The passenger front airbag gas is vented through the vent holes in the sides of the airbag. In this way, the airbags do not interfere with your control of the vehicle.


† The Side Impact SRS Side Curtain Airbags are de- signed to activate only in certain side or rollover collisions. When the Occupant Restraint Control Mod- ule (ORC) detects a collision requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle both sides of the vehicle if equipped with rollover sensing. A quantity of nontoxic gas is generated to inflate the window bag. The inflating window bag pushes the outside edge of the headliner out of the way and covers the window. The airbag inflates in about 30 milliseconds (about one-quarter of the time it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the window bag inflates. This especially applies to chil- dren. The window bag is only about 3 inches (8 cm) thick when it is inflated.


† The Knee Impact Bolsters help protect the knees of the driver and the front passenger, and position every- one for the best interaction with the front airbag.


If A Deployment Occurs The airbag system is designed to deploy when the Occupant Restraint Control (ORC) Module detects a moderate-to-severe frontal collision, to help restrain the driver and front passenger, and then to immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: † The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55


passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. † As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instruc- tions for cleaning.


56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


† It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you.


WARNING!


Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and seat belt retractor assem- bly, replaced by an authorized dealer as soon as possible.


Enhanced Accident Response Feature If the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically. The hazard lights will flash and the fuel will be cut off to the engine. In addition, after the vehicle has stopped moving, the interior lights will illuminate to aid visibility and remain lit until the ignition switch is turned off. NOTE: The interior lights can only be deactivated if the key is removed from the ignition switch or the vehicle is driven.


Maintaining Your Airbag System


WARNING!


† Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper or vehicle body structure. † You need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee bolsters. † It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has an airbag system.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57


See


NOTE: Perchlorate Material – special handling may apply, www.dtsc.ca.gov/hazardouswaste/ perchlorate Airbag Warning Light You will want to have the airbag system ready to inflate for your protection in an impact. The airbag system is designed to be maintenance free. If any of the following occurs, have an authorized dealer service the system promptly: † Does not come on during the 2.5 to 8 seconds after the † Remains on after the 2.5 to 8 second interval. † Flickers, or comes on and remains on for any period of


ignition switch is first turned on.


time while driving.


58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


Event Data Recorder (EDR) In the event of an accident, your vehicle is designed to record up to 5-seconds of specific vehicle data parameters (see the following list) in an event data recorder prior to the moment of airbag deployment, or near deployment, and up to a quarter second of high-speed deceleration data during and/or after air bag deployment or near- deployment. EDR data are ONLY recorded if an airbag deploys, or nearly deploys, and are otherwise unavail- able. NOTE: † A near-deployment event occurs when the airbag sensor detects severe vehicle deceleration usually in- dicative of a crash, but not severe enough to warrant airbag deployment. † Under certain circumstances, EDR data may not be


recorded (e.g., loss of battery power).


In conjunction with other data gathered during a com- plete accident investigation, the electronic data may be used by DaimlerChrysler Corporation and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle perfor- mance. In addition to crash investigations initiated by DaimlerChrysler Corporation, such investigations may be requested by customers, insurance carriers, govern- ment officials, and professional crash researchers, such as those associated with universities, and with hospital and insurance organizations. In the event that an investigation is undertaken by DaimlerChrysler Corporation (regardless of initiative), the company or its designated representative will first obtain permission of the appropriate custodial entity for the vehicle (usually the vehicle owner or lessee) before accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., pursuant to a warrant). A copy of the data will be


provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US govern- ment and various states. Data of a potentially sensitive nature, such as would identify a particular driver, ve- hicle, or crash, will be treated confidentially. Confidential data will not be disclosed by DaimlerChrysler Corpora- tion to any third party except when: 1. Used for research purposes, such as to match data with a particular crash record in an aggregate database, provided confidentiality of personal data is thereafter preserved 2. Used DaimlerChrysler Corporation product 3. Requested by police under a legal warrant 4. Otherwise required by law


involving


litigation


defense


of


in


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59


Data Parameters that May Be Recorded: † Diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system


cycles and vehicle mileage)


† Airbag disable lamp status (if equipped) † 9Time9 of airbag deployment (in terms of ignition † Airbag deployment level (if applicable) † Impact acceleration and angle † Seat belt status † Brake status (service and parking brakes) † Accelerator status (including vehicle speed) † Engine control status (including engine speed) † Transmission gear selection


60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


† Cruise control status † Traction/stability control status † Tire pressure monitoring system status Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buck- led up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front.


There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat Owner’s Manual to ensure you have the right seat for your child. Use the restraint that is correct for your child:


WARNING!


In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.


Infants and Child Restraints † Safety


experts


recommend that


children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and “convertible” child seats. † The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). “Convertible” child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 20
lbs (9 kg) but are less than one year old. Both types of child restraints are held in the vehicle by the lap/ shoulder belt or the LATCH child restraint anchorage system (Refer to LATCH — Child Seat Anchorage System in this section.)


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61


† Rearward-facing child seats must NEVER be used in the front seat of a vehicle with the front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position.


WARNING!


† Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. † A rearward facing infant restraint should only be used in a rear seat. A rearward facing infant restraint in the front seat may be struck by a deploying passenger airbag which may cause se- vere or fatal injury to the infant.


62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


Here are some tips for getting the most out of your child restraint: † Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. The manufacturer also recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. † The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. † Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it. † The front passenger seat belt is equipped with a cinching latch plate. The second and third row seating positions have automatic locking retractors. Both types of seat belts are designed to keep the lap portion tight


around the child restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt (the cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary). For the second and third row seat belts with the automatic locking retractor, pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then, pull the belt until it is fully extracted from the retrac- tor. Allow the belt to return to the retractor, pulling on the excess webbing to tighten the lap portion about the child restraint. For additional information, refer to 9Automatic Locking Mode9 earlier in this section. † In your vehicle’s 2nd row outboard seating positions, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate


is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. † If the belt still cannot be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still cannot make the child restraint secure, try a different seating position. † Buckle the child into the restraint exactly as the † When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seat backs and cause serious personal injury.


manufacturer’s instructions tell you.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63


to


For


refer


additional


information


NOTE: www.seatcheck.org or call 1-866-SEATCHECK. Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction, are for chil- dren who weigh 20 to 40 lbs (9 to 18 kg), and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system (Refer to LATCH — Child Seat Anchorage System in this section.) The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seat back, they should use a


64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


belt-positioning booster seat. The child and belt- positioning booster seat are held in the vehicle by the lap/shoulder belt. Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat. † Make sure that the child is upright in the seat. † The lap portion should be low on the hips and as snug † Check belt fit periodically. A child’s squirming or † If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.


slouching can move the belt out of position.


as possible.


LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CHildren) Your vehicle’s second row seat is equipped with the child restraint anchorage system called LATCH. The LATCH system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securing the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure. LATCH-compatible child restraint systems are now avail- able. However, because the lower anchorages are to be introduced over a period of years, child restraint systems having attachments for those anchorages will continue to also have features for installation using the vehicle’s seat belts. Child restraints having tether straps and hooks for connection to the top tether anchorages have been avail- able for some time. For some older child restraints, many child restraint manufacturers offer add-on tether strap


kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child re- straint in any vehicle. NOTE: When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle. The second row outboard seating positions have lower anchorages that are capable of accommodating LATCH- compatible child seats having flexible, webbing-mounted lower attachments. Child seats with fixed lower attach- ments must be installed in the outboard positions only. Regardless of the specific type of lower attachment, NEVER install LATCH-compatible child seats such that two seats share a common lower anchorage.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65


If you are installing LATCH-compatible child restraints in adjacent rear seating positions, you can use the LATCH anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position. If your child restraints are not LATCH- compatible, you can only install the child restraints using the vehicle’s seat belts. Please refer to the next section for typical installation instructions. Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system. The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seat back, and are just visible when you lean into the rear seat to


66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces.


Latch Anchorages


In addition, there are tether strap anchorages behind each rear outboard seating position located on the back of the seat.


Tether Strap Mounting


Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forward- facing toddler restraints and some rear-facing infant restraints will also be equipped with a tether strap, a


hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next attach the lower hooks or connectors over the top of the anchorage bars, pushing aside the seat cover material. Then, locate the tether anchorage directly behind the seat where you are placing the child restraint and attach the tether strap to the anchorage, being careful to route the tether strap to provide the most direct path between the anchor and the child restraint. Finally, tighten all three straps as you push the child restraint rearward and downward into the seat, removing slack in the straps according to the child restraint manufacturer’s instruc- tions.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67


WARNING!


Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.


Installing Child Restraints Using the Vehicle Seat Belt The passenger seat belts are equipped with either cinch- ing latch plates or automatic locking retractors, which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary.


68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


If the seat belt has an automatic locking retractor, pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then, pull the belt until it is all extracted from the retractor. Allow the belt to return to the retractor, pulling on the excess webbing to tighten the lap portion about the child restraint. Refer to “Automatic Locking Mode” earlier in this section. In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate from


the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. To attach a child restraint tether strap:


Tether Strap Mounting


Route the tether strap over the seat back and attach the hook to the tether anchor located on the back of the seat.


For the outboard seating positions, route the tether over the head rests, and attach the hook to the tether anchor located on the back of the seat.


WARNING!


An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.


Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69


ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55
mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- mental and should be avoided. The engine oil installed in the engine at the factory is a high quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. The recommended viscosity and quality grades are shown in Section 7 of this manual. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED.


70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty.


SAFETY TIPS


Exhaust Gas


WARNING!


Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below.


† Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for a extended period. If the vehicle is stopped in an open area with engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle. † Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. † Always run the climate control in panel or floor mode when driving with any windows open, even if only slightly, to help keep fresh air circulating inside ve- hicle. Otherwise poisonous gases could be drawn into the vehicle.


Safety Checks You Should Make Inside The Vehicle


Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt.


THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71


Airbag Warning Light The light should come on and remain on for 6 to 8
seconds as a bulb check when the ignition switch is first turned on. If the bulb is not lit during starting, have it replaced. If the light stays on or comes on while driving, have the system checked by an authorized dealer. Defrosters Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoper- able.


72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE


Safety Checks You Should Make Outside The Vehicle


Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks. Check wheel nuts for tightness and tires (includ- ing spare) for proper pressure.


Lights Have someone observe the operation of all exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Fluid Leaks Check area under vehicle after overnight parking for fuel, coolant, oil or other fluid leaks. Also, if gasoline fumes are detected, the cause should be located and corrected immediately.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE


CONTENTS


m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
N Inside Day/Night Mirror . . . . . . . . . . . . . . . . .78
N Automatic Dimming Mirror — If Equipped . . . .78
N Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .79
N Exterior Mirrors Folding Feature . . . . . . . . . . .80
N Driver’s And Front Passenger Outside


Automatic Dimming Mirror — If Equipped . . . .80


N Power Remote Control Outside Mirrors —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .80


N Heated Remote Control Mirrors —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .81
N Lighted Vanity Mirrors — If Equipped . . . . . . .81


m Hands–Free Communication (UConnect™) —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
N Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
N Phone Call Features . . . . . . . . . . . . . . . . . . . .91
N UConnect™ System Features . . . . . . . . . . . . . .94
N Advanced Phone Connectivity . . . . . . . . . . . . .98


74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


N Things You Should Know About Your


UConnect™ System . . . . . . . . . . . . . . . . . . . . 100
N General Information . . . . . . . . . . . . . . . . . . . 108
m Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
N Front Manual Seat Adjustment . . . . . . . . . . . . 108
N Front Seat Adjustment — Recline . . . . . . . . . . 108
N Manual Lumbar Support Adjustment . . . . . . . 109
N 8 - Way Driver’s Power Seat . . . . . . . . . . . . . . 110
N 4 - Way Passenger’s Power Seat —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 110
N Head Restraints . . . . . . . . . . . . . . . . . . . . . . 110
N Front Heated Seats—If Equipped . . . . . . . . . . 111
N 40/20/40 Second Row Folding Seat . . . . . . . . 113


N 50/50 Third Row Folding Seat —


If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 117
m Driver Memory Seat — If Equipped . . . . . . . . . 118


N Setting Memory Positions And Linking Remote


Keyless Entry Transmitter To Memory . . . . . . . 119
N Memory Position Recall . . . . . . . . . . . . . . . . . 120
N To Disable A Transmitter Linked To Memory . . 121
N Easy Entry/Exit Seat . . . . . . . . . . . . . . . . . . . 122
m To Open And Close The Hood . . . . . . . . . . . . . 123
m Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
N Multi-Function Control Lever . . . . . . . . . . . . . 124
N Battery Saver Feature—Exterior/Interior


Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
. . . . . . . . . . . 125


N Headlights And Parking Lights


N Automatic Headlight System — If Equipped . . 126
N SmartBeams — If Equipped . . . . . . . . . . . . . . 126
N Instrument Panel And Interior Lights . . . . . . . 127
N Daytime Running Lights — If Equipped . . . . . 128
N Lights-On Reminder . . . . . . . . . . . . . . . . . . . 128
N Fog Lights — If Equipped . . . . . . . . . . . . . . . 128
N Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 129
N High Beam Switch . . . . . . . . . . . . . . . . . . . . 129
N Passing Light . . . . . . . . . . . . . . . . . . . . . . . . 129
N Headlight Time Delay . . . . . . . . . . . . . . . . . . 129
N Interior Lights . . . . . . . . . . . . . . . . . . . . . . . 130
N Courtesy/Reading Lights . . . . . . . . . . . . . . . . 130
m Windshield Wipers And Washers . . . . . . . . . . . . 131


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75


N Mist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
N Speed Sensitive Intermittent Wiper System . . . 132
N Rain Sensing Wipers—If Equipped . . . . . . . . . 133
m Tilt/Telescoping Steering Column . . . . . . . . . . . 134
m Adjustable Pedals — If Equipped . . . . . . . . . . . 135
m Electronic Speed Control — If Equipped . . . . . . 136
N Electronic Speed Control Operation . . . . . . . . 136
N To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . 137
N To Set At A Desired Speed . . . . . . . . . . . . . . . 137
N To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . 138
N To Resume Speed . . . . . . . . . . . . . . . . . . . . . 138
N To Vary The Speed Setting . . . . . . . . . . . . . . . 138
N To Accelerate For Passing . . . . . . . . . . . . . . . 139


76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


m Electronic Brake Control System . . . . . . . . . . . . 139
N ABS (Anti-Lock Brake System) . . . . . . . . . . . . 139
N TCS (Traction Control System) . . . . . . . . . . . . 140
N BAS (Brake Assist System) . . . . . . . . . . . . . . . 141
N ERM (Electronic Roll Mitigation) . . . . . . . . . . 142
N ESP (Electronic Stability Program) . . . . . . . . . 143
N TSC (Trailer Sway Control) . . . . . . . . . . . . . . 147
N HSA (Hill Start Assist) (4WD Models With


NV245 Two–Speed Transfer Case Only) . . . . . . 148


N HDC (Hill Descent Control) (4WD Models


With NV245 Two–Speed Transfer Case Only) . . 150


N ESP/BAS Warning Lamp And ESP/TCS


Indicator Light


. . . . . . . . . . . . . . . . . . . . . . . 152
m Rear Park Assist System— If Equipped . . . . . . . 153


N Rear Park Assist Sensors . . . . . . . . . . . . . . . . 154
N Rear Park Assist Warning Display . . . . . . . . . 154
N Enable/Disable The Rear Park Assist System . . 156
N Service The Rear Park Assist System . . . . . . . . 156
N Cleaning The Rear Park Assist System . . . . . . 157
m Rear Camera — If Equipped . . . . . . . . . . . . . . . 157
N Turning The Rear Camera On . . . . . . . . . . . . 157
N Turning The Rear Camera Off . . . . . . . . . . . . 158
m Overhead Console — If Equipped . . . . . . . . . . . 158
m Garage Door Opener — If Equipped . . . . . . . . . 159
N Programming HomeLinkt . . . . . . . . . . . . . . . 160
N Gate Operator/Canadian Programming . . . . . 163
N Using HomeLinkt . . . . . . . . . . . . . . . . . . . . . 163


N Reprogramming a Single HomeLinkt Button . . 164
N Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
N Troubleshooting Tips . . . . . . . . . . . . . . . . . . . 164
N General Information . . . . . . . . . . . . . . . . . . . 165
m Power Sunroof — If Equipped . . . . . . . . . . . . . 165
N Opening Sunroof - Express . . . . . . . . . . . . . . 166
N Closing Sunroof - Express . . . . . . . . . . . . . . . 166
N Pinch Protect Feature . . . . . . . . . . . . . . . . . . . 166
N Pinch Protect Override . . . . . . . . . . . . . . . . . 167
N Venting Sunroof - Express . . . . . . . . . . . . . . . 167
N Sunshade Operation . . . . . . . . . . . . . . . . . . . 167
N Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 167
N Sunroof Maintenance . . . . . . . . . . . . . . . . . . . 168
N Ignition Off Operation . . . . . . . . . . . . . . . . . . 168


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77


N Sunroof Fully Closed . . . . . . . . . . . . . . . . . . . 168
m Command-View™ Skylights — If Equipped . . . . 168
m Power Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . 169
N Front Power Outlet . . . . . . . . . . . . . . . . . . . . 169
N Rear Power Outlet — If Equipped . . . . . . . . . 169
m Power Inverter — If Equipped . . . . . . . . . . . . . 170
m Cup Holders . . . . . . . . . . . . . . . . . . . . . . . . . . 172
m Cargo Area Features . . . . . . . . . . . . . . . . . . . . . 174
N Cargo Load Floor . . . . . . . . . . . . . . . . . . . . . 174
m Rear Window Features . . . . . . . . . . . . . . . . . . . 176
N Rear Window Wiper/Washer . . . . . . . . . . . . . 176
N Rear Window Defroster — If Equipped . . . . . . 177
m Roof Luggage Rack — If Equipped . . . . . . . . . . 177


78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


MIRRORS


Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window.


A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield). Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will indicate when the dimming feature is activated.


Adjusting Rear View Mirror


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79


Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.


WARNING!


Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. Some vehicles will not have a convex passenger side mirror.


Automatic Dimming Mirror


CAUTION!


To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.


80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


Exterior Mirrors Folding Feature All exterior mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward, and normal. Driver’s and Front Passenger Outside Automatic Dimming Mirror — If Equipped If your vehicle is equipped with outside automatic dim- ming mirrors, they will operate when the inside auto- matic dimming mirror is on. The outside mirrors operate off the inside mirror switch and will automatically adjust for annoying headlight glare when the inside mirror does. Power Remote Control Outside Mirrors — If Equipped The power mirror switch is located on the driver’s door trim panel next to the power door lock switch. A rotary knob selects the left mirror, right mirror, or off position.


After selecting a mirror move the knob in the same direction you want the mirror to move. Use the center off position to guard against accidentally moving a mirror position.


Power Mirror Switches


Power mirror preselected positions can be controlled by the optional Memory Seat Feature. Refer to “Driver Memory Seat” in this section for details. Heated Remote Control Mirrors — If Equipped


These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear


window defrost. Lighted Vanity Mirrors — If Equipped To access a lighted vanity mirror, flip down one of the visors. Lift the cover to reveal the mirror. The light will turn on automatically.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81


Lighted Vanity Mirror Sun Visor Extension (If Equipped) This feature has a pull out extension on the sun visor for increased coverage.


82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED


NOTE: The sales code RER radio contains an inte- grated Hands-Free Communication (UConnect™) sys- tem. Refer to your “Navigation User’s Manual” for UConnect™ system operating instructions for this ra- dio. UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., 9Call” { “Mike” {”Work9 or 9Dial” { “248-555-12129). Your cellular phone’s audio is trans- mitted through your vehicle’s audio system; the system will automatically mute your radio when using the UConnect™ system.


NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth 9Hands-Free Profile,9
version 0.96 or higher. See UConnect™ website for sup- ported phones. NOTE: For UConnect™ customer support, visit the following web sites: † www.chrysler.com/uconnect † www.dodge.com/uconnect † www.jeep.com/uconnect † or call 1–877–855–8400
UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversation.


The UConnect™ phone book enables you to store up to 32 names and four numbers per name. Each language has a separate 32-name phone book accessible only in that language. This system is driven through your Blue- tooth™ Hands-Free profile cellular phone. UConnect™ features Bluetooth™ technology - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so UCon- nect works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s UConnect™ system. The UConnect™ system allows up to seven cellular phones to be linked to system. Only one linked (or paired) cellular phone can be used with the system at a time. The system is available in English, Spanish, or French languages (as equipped).


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83


Phone Button


The rearview mirror contains the microphone for the system (depending on the type of mirror and radio equipped), and either the radio or the mirror has the two control buttons (Phone Button and Voice Recognition Button) that will enable you to access the system.


Voice Recognition Button


Actual button location may vary with radio. The individual buttons are described in the “Operation” section.


The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. See UConnect™ website for supported phones. If your cellu- lar phone supports a different profile (e.g., Headset Profile) you may not be able to use any UConnect™ features. Refer to your cellular service provider or the phone manufacturer for details.


84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


The UConnect™ system is fully integrated with the vehicle’s audio system. The volume of the UConnect™ system can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect™ system such as 9CELL9 or caller ID on certain radios. Operation Voice commands can be used to operate the UConnect™ system and to navigate through the UConnect™ menu structure. Voice commands are required after most UConnect™ system prompts. You will be prompted for a specific command and then guided through the available options. † Prior to giving a voice command, one must wait for the beep, which follows the 9Ready9 prompt or another prompt.


† For certain operations, compound commands can be used. For example, instead of saying 9Setup9 and then 9Phone Pairing,9 the following compound command can be said: 9Setup Phone Pairing.9
† For each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command, when you are asked for it. For example, you can use the combined form voice com- mand 9Phonebook New Entry,9 or you can break the combined form command into two voice commands: 9Phonebook9 and 9New Entry.9 Please remember, the UConnect™ system works best when you talk in a normal conversational tone, as if speaking to some one sitting eight feet away from you.


Voice Command Tree Refer to “Voice Tree” at the end of this section.


Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say 9Help9 following the beep. The UConnect™ system will play all the options at any prompt if you ask for help. To activate the UConnect™ system from idle, simply press the “Phone” button and follow audible prompts for directions. All UConnect™ system sessions begin with a press of the “Phone” button on the radio control head. Cancel Command At any prompt, after the beep, you can say 9Cancel9 and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (Link) UConnect™ System to a Cellular Phone To begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone.


UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85


To complete the pairing process, you will need to refer- ence your cellular phone owner’s manual. The UCon- nect™ website may also provide detailed instructions for pairing. The following are general phone to UConnect™ System pairing instructions: † Press the “Phone” button to begin. † After the 9Ready9 prompt and the following beep, say † When prompted, after the beep, say 9Pair a Phone9 and † You will be asked to say a four-digit pin number, which you will later need to enter into your cellular. You can enter any four-digit pin number. You will not need to remember this pin number after the initial pairing process.


follow the audible prompts.


9Setup Phone Pairing.9


86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE


† For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. † You will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority. You can pair up to seven cellular phones to your UConnect™ system. However, at any given time, only one cellular phone can be in use, connected to your UConnect™ System. The priority allows the UConnect™ system to know which cellular phone to use if multiple cellular phones are in the vehicle at the same time. For example, if priority 3 and priority 5
phones are present in the vehicle, the UConnect™ system will use the priority 3 cellular phone when you

Loading...
x