2005 Hyundai Santa FE Owners Manual

Download PDF Manual
5. Replace two conditioner filters by pulling the knob of the air conditioner filter outward. Installation is the reverse order of disassem- bly. CAUTION: Be sure to install the air conditioner filter in the direction of the arrow sign. Otherwise, it may cause noise or deterioration. G150A01O To check the steering wheel free-play, stop the car with the wheels pointed straight ahead and gently move the steering wheel back and forth. Use very light finger pressure and be sensitive to changes in resistance that mark the limits of the free-play. If the free-play is greater than specified, have it inspected by your Hyundai dealer and adjusted or repaired if necessary. G170A01A-AAT BRAKE PEDAL CHECKING BRAKE PEDAL CLEARANCE G180A01A-AAT 0.12 ~ 0.31 in. (3 ~ 8 mm) 2.95 in. (75 mm) G160A01HR With the engine off, press down on the brake pedal several times to reduce the vacuum in the brake booster. Then, using your hand, press down slowly on the brake pedal until you feel a change in resistance. This is the brake pedal free-play. The free-play should be within the limits speci- fied in the illustration above. If it is not, have it inspected by your Hyundai dealer and adjusted or repaired if necessary. G180A01L You need a helper to check the brake pedal clearance. With the engine running, have your helper press down on the brake pedal several times and then hold it down with a force of about 110 lbs (50 kg, 490 N). The brake pedal clear- ance is the distance from the top surface of the brake pedal to the asphalt sheeting under the floor mat. If the brake pedal clearance is not within the limits specified in the illustration, have it in- spected by your Hyundai dealer and adjusted or repaired if necessary. DO-IT-YOURSELF MAINTENANCE CHECKING DRIVE BELTS 19 G190A01A-AAT 2.7 V6 Auto tensioner Power steering pulley A/C comp. Generator Crankshaft pulley G190A02B 3.5 V6 Power steering pulley Generator Crankshaft pulley A/C pulley G140D02L 6 DO-IT-YOURSELF MAINTENANCE 20 Drive belts should be checked periodically for proper tension and adjusted if necessary. At the same time, belts should be examined for cracks, wear, fraying or other evidence of deterioration and replaced if necessary. Belt routing should also be checked to be sure there is no interference between the belts and other parts of the engine. After a belt is replaced, the new belt should be adjusted again after two or three weeks to eliminate slack resulting from initial stretching after use. CAUTION: When replacing a fusible link, never use anything but a new fusible link with the same or lower amperage rating. Never use a piece of wire or a higher-rated fusible link. This could result in serious damage and create a fire hazard. CHECKING AND REPLACING FUSES G200A03A-AAT Replacing a Fusible Link Open- Replace Good G200A01O A fusible link will melt if the electrical circuits from the battery are ever overloaded, thus prevent- ing damage to the entire wiring harness. (This could be caused by a short in the system drawing too much current.) If this ever happens, have a Hyundai dealer determine the cause, repair the system and replace the fusible link. The fusible links are located in a relay box in the engine compartment for easy inspection. 1. Turn off the ignition and all other switches. 2. Open the fuse box and examine each fuse. Remove each fuse by pulling it toward you (a small "fuse puller" tool is contained in the relay and fuse box of the engine room to simplify this operation). 3. Be sure to check all other fuses even if you find one that appears to have opened. DO-IT-YOURSELF MAINTENANCE 21 4. Replace the blown fuse by pressing a new fuse of the same rating into place. The fuse should be a snug fit. If it is not, have the fuse clip repaired or replaced by a Hyundai dealer. If you do not have a spare fuse, you may be able to borrow a fuse of the same or lower rating from an accessory you can tempo- rarily get along without (the radio or cigarette lighter, for example). Always remember to replace the borrowed fuse. G200A02O Good Open-Replace G200B02L G200B02HP-AAT Replacing Accessory Fuses HSM4002 The fuse box for the lights and other electrical accessories will be found low on the dashboard on the driver's side. Inside the box you will find a list showing the circuits protected by each fuse. If any of your car's lights or other electrical accessories stop working, a blown (open) fuse could be the reason. If the fuse has opened, you will see that the metal strip inside the fuse has melted through. If you suspect a blown fuse, follow this procedure: 6 DO-IT-YOURSELF MAINTENANCE 22 CHECKING THE BATTERY G210A01A-AAT CAUTION: An open fuse indicates that there is a prob- lem in the electrical circuit. If you replace a fuse and it blows as soon as the accessory is turned on, the problem is serious and should be referred to a Hyundai dealer for diagnosis and repair. Never replace a fuse with anything except a fuse with the same or a lower amperage rating. A higher capac- ity fuse could cause damage and create a fire hazard. NOTE: See page 6-33 for the fuse panel descrip- tions. D010B01O WARNING: Batteries can be dangerous! When working with batteries, carefully observe the follow- ing precautions to avoid serious injuries. The fluid in the battery contains a strong solution of sulfuric acid, which is poisonous and highly corrosive. Be careful not to spill it on yourself or the car. If you do spill battery fluid on yourself, immediately do the following: o If battery fluid is on your skin, flush the affected areas with water for at least 15 minutes and then seek medical assistance. o If battery fluid is in your eyes, rinse out your eyes with water and get medical assistance as soon as possible. While you are being driven to get medical assistance, continue to rinse your eyes by using a sponge or soft cloth saturated with water. o If you swallow battery fluid, drink a large quantity of water or milk followed by milk of magnesia, eat a raw egg or drink vegetable oil. Get medical assistance as soon as possible. While batteries are being charged (either by a battery charger or by the vehicle's generator), they produce explosive gases. Always ob- serve these warnings to prevent injuries from occurring: o Charge batteries only in a well ventilated o Do not permit flames, sparks or smoking in area. the area. o Keep children away from the area. G210B03A-AAT Checking the Battery Keep the battery clean. Any evidence of corro- sion around the battery posts or terminals should be removed using a solution of house- hold baking soda and warm water. After the battery terminals are dry, cover them with a light coating of grease. PROPOSITION 65 WARNING: Battery posts, terminals, and related acces- sories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Batteries also contain other chemicals known to the State of California to cause cancer. Wash hands after handling. CHECKING ELECTRIC COOLING FANS G220A01A-AAT DO-IT-YOURSELF MAINTENANCE POWER STEERING FLUID LEVEL 23 G230A03A-AAT WARNING: The cooling fan is controlled by engine coolant temperature and may sometimes operate even when the engine is not run- ning. Use extreme caution when working near the blades of the cooling fan, so that you are not injured by a rotating fan blade. As the engine coolant temperature de- creases the fan will automatically shut off. This is a normal condition. G220B01A-AAT Checking Engine Cooling Fan The engine cooling fan should come on auto- matically if the engine coolant temperature is high. G220C01A-AAT Checking Condenser Cooling Fan The condenser cooling fan should come on automatically whenever the air conditioning is in operation. HSM5010 The power steering fluid level should be checked regularly. To check the power steering fluid level, be sure the engine is "OFF", then check to make certain that the power steering fluid level is between the "MAX" and "MIN" level markings on the fluid reservoir. NOTE: Grinding noise from the power steering pump may be heard immediately after the engine is started in extremely cold condi- tions (below - 4°F). If the noise stops during warm up, there is no abnormal function in the system. It is due to a power steering fluid characteristic in extremely cold condi- tions. 6 DO-IT-YOURSELF MAINTENANCE 24 Recommended Fluid Use PSF-3 type fluid NOTE: Do not start the engine when the power steering oil reservoir is empty. G240A01A-AAT POWER STEERING HOSES It is suggested that you check the power steer- ing hose connections for fluid leakage at those intervals specified in the vehicle maintenance schedule in Section 5. The power steering hoses should be replaced if there is severe surface cracking, pulling, scuffing or worn spots. Deterioration of the hose could cause premature failure. G250A01A-AAT FOR MORE INFORMATION ABOUT YOUR HYUNDAI If you desire additional information about main- taining and servicing your Hyundai, you may purchase a factory Shop Manual at your Hyundai dealer's parts department. This is the same manual used by dealership technicians and while it is highly technical it can be useful in obtaining a better understanding of your car and how it works. HEADLIGHT AIMING ADJUSTMENT G290A02O-AAT Before performing aiming adjustment, make sure of the following. 1. Keep all tires inflated to the correct pressure. 2. Place the vehicle on level ground and press the front bumper & rear bumper down sev- eral times. Place vehicle at a distance of 118 in. (3m) from the test wall. 3. See that the vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tire, jack, and tools). Have the driver or equivalent weight placed in driver's seat. 4. Clean the head light lenses and turn on the headlights (Low beam). 5. Open the hood. Vertical aiming G290A01O 6. Draw a vertical line (through the center of each headlight beam pattern) and a horizon- tal line (through the center of each headlight beam pattern) on the aiming screen. And then, draw a parallel line at 0.8 in. (21 mm) under the horizontal line. 7. Adjust each cut-off line of the low beam to the parallel line with a phillips screwdriver - VERTICAL AIMING. WARNING: Horizontal aiming should be adjusted by an authorized Hyundai dealer. DO-IT-YOURSELF MAINTENANCE 25 G290B01O-AAT Adjustment After Headlight Assembly Replacement Vertical line Horizontal line Cut-off line "P" Ground line SPECIFICATION: "H"; Horizontal center line of headlights from ground: 2WD : 32.5 in.(822 mm) 4WD : 33.3 in.(843 mm) "W"; Distance between each headlight center: 46.5 in.(1,178 mm) "L"; Distance between the headlights and the wall that the lights are tested against: 118 in. (3,000 mm). G290A03O If the vehicle has had front body repair and the headlight assembly has been replaced, the headlight aiming should be checked using an aiming chart as shown in the illustration. Turn on the headlight switch. (Low Beam Position) 1. Adjust headlights so that main axis of light is parallel to center line of the body and is aligned with point "P" shown in the illustration. 2. Dotted lines in the illustration show the center of headlights. 6 DO-IT-YOURSELF MAINTENANCE 26 REPLACEMENT OF LIGHT BULBS G260A02A-AAT Before attempting to replace a light bulb, be sure the switch is turned to the "OFF" position. The next paragraph shows how to reach the light bulbs so they may be changed. Be sure to replace the burned-out bulb with one of the same number and wattage rating. See page 6-32 for the wattage description. G270A02O-AAT Headlight and Front Turn Signal Light 1. Allow the bulb to cool. Wear eye protection. 2. Open the engine hood. 3. Always grasp the bulb by its plastic base, avoid touching the glass. CAUTION: Keep the lamps out of contact with petro- leum products, such as oil, gasoline, etc. 4. Using a socket wrench of the correct size, remove the headlight assembly mounting bolts. HSM353 HSM328 5. Disconnect the power cord from the bulb base in the back of the headlight. G270A01O 6. Turn the plastic cover counterclockwise and remove it. DO-IT-YOURSELF MAINTENANCE 27 HSM329 7. Disconnect the connector from the bulb base in the back of the headlight. HSM330 8. Push the bulb spring to remove the headlight bulb. HSM331 9. Remove the protective cap from the re- placement bulb and install the new bulb by matching the plastic base with the headlight hole. Reattach the bulb spring and recon- nect the connector. 10.Use the protective cap and carton to prompt- ly dispose of the old bulb. 11.Check for proper headlight aim. 6 DO-IT-YOURSELF MAINTENANCE 28 HSM332 12.To replace the front turn signal light bulb, remove from the bulb holder and install the new bulb. Do not touch the glass of the new bulb. G270B02O-GAT Rear Combination Light (1) G270A03O (2) (3) WARNING: This halogen bulb contains gas under pres- sure and if impacted could shatter, result- ing in flying fragments. Always wear eye protection when servicing the bulb. Protect the bulb against abrasions or scratches and against liquids when lighted. Turn the bulb on only when installing in a headlight. Replace the headlight if damaged or cracked. Keep the bulb out of the reach of children and dispose of the used bulb with care. G270B01O G270B02O 1. Open the tail gate. 2. Remove the mounting screws of the rear combination light as shown with a phillips screwdriver. G270C01O-AAT Luggage Compartment Light DO-IT-YOURSELF MAINTENANCE 29 (2) (1) (3) G270B03O 3. To replace the rear combination light, take it out from the bulb holder by turning it coun- terclockwise. (1) Stop/Tail light (2) Back-up light (3) Turn signal light 4. Install the new bulb. HSM341 3. Replace with a new bulb. HSM342 1. Open the tail gate. 2. Remove the cover with a flat-head screw- driver. 6 DO-IT-YOURSELF MAINTENANCE 30 G270E01O-AAT Front Side Marker Light G270G01O-AAT Interior Light HSM334 1. Remove the cover with a phillips screw- driver. 2. Disconnect the connector. HSM335 HSM343 1. Remove the cover with a flat-head screw- driver. 3. Replace with a new bulb. HSM336 G270H01O-AAT Glove Box Illuminated Light DO-IT-YOURSELF MAINTENANCE 31 2. Replace with a new bulb. HSM344 HSM366 3. Disconnect the connector. G270E02L 1. Open the glove box. 2. Remove the cover with a flat-head screw- driver. 4. Replace with a new bulb. HTB284 6 DO-IT-YOURSELF MAINTENANCE 32 BULB WATTAGE G280A03O-AAT No. Part Name Wattage Socket type Glove Box Illuminated Light Headlight (Low/High) Turn Signal Light/Front Position Light Map Light With sunroof Without sunroof Interior Light Front Fog Light (If installed) Side Marker Light 55/60 28/8 10 10 27 S8.5/8.5 P43t BA15d BA9s BA9s S8.5/8.5 PG13 W2.1×9.5D 12 No. 10 11 Part Name Wattage Front Door Edge Warning Light (If installed) Luggage Compartment Light High Mounted Rear Stop Light (If installed) Rear Combination Light Turn Signal Light Stop/Tail Light (Side Marker Light) Back-up Light License Plate Light 10 17 27 27/8(8) 27 G280A01O-A Socket type W2.1×4.6D S8.5/8.5 W-2 BA15s BA15d BA15s W2.1×9.5D FUSE PANEL DESCRIPTION G200C02O-AAT Engine Compartment DO-IT-YOURSELF MAINTENANCE 33 DESCRIPTION FUSE RATING PROTECTED COMPONENTS FUSIBLE LINK FUSE ALT B+ IGN BLR ABS.1 ABS.2 ECU P/W RAD FAN C/FAN FRT FOG H/LP(LH) H/LP(RH) ECU #1 ECU #2 ECU #3 ECU(B+) ATM HORN A/C ST SIG 140A 50A 50A 40A 30A 30A 40A 30A 40A 20A 15A 10A 10A 20A 20A 10A 15A 20A 10A 10A 10A Generator Tail lamp relay, Fuse 11~17, Power connector Start relay, Ignition switch A/C Fuse, Blower relay ABS control module, Air bleeding connector ABS control module, Air bleeding connector Engine contorl relay Power window relay, Fuse 26 Radiator fan relay Condenser fan relay Fog lamp relay Left head lamp, Instrument cluster, DRL control module Right head lamp Ignition failure sensor, Oxygen sensor Injector Check engine ind, ECM, PCM Fuel pump relay, ECM, TCM, Generator, PCM ATM contorl relay, 4WD control module Horn relay A/C relay PCM, ECM NOTE: Not all fuse panel descriptions in this manual may be applicable to your vehicle. It is accurate at the time of printing. When you inspect the fuse box on your vehicle, refer to the fuse box label. G200C01O 6 DO-IT-YOURSELF MAINTENANCE 34 G200E01O-AAT Inner Panel FUSE FUSE RATING PROTECTED COMPONENTS F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24 F25 F26 F27 F28 F29 F30 F31 20A 10A 15A 10A 10A 25A 10A 10A 10A 10A 10A 15A 20A 10A 10A 25A 20A 30A 10A 15A 10A 10A 10A 10A 10A 20A 10A 10A 15A 10A 20A Cigarette lighter & Power outlet Audio, Power outside mirror Digital clock, Rear power outlet Cruise control Head lamp relay Seat warmer Rear wiper motor control Rear window defogger, Power outside mirror A/C control, Sunroof controller, Electrical chrome mirror (Not used) Room lamp, Door warning switch, Door lamp, Manual A/C control, Homelink controller Digatal clock, ETACM, Audio, Siren AMP speakers Stop lamp, Data link connector, Multipurpose check connector Hazard lamp Power seat, Rear wiper motor control Sunroof controller Defogger relay Instrument cluster, Pre-excitation resistor, ETACM, Auto light sensor, DRL control module, Generator SRS control module ECM (V6 2.7L) Instrument cluster (Airbag IND) ABS control module, G-Sensor, Air bledding connector, 4WD control module Turn signal lamp Back-up lamps, TCM, Vehicle speed secsor, ETS control module, Ignition failure sensor Door lock/unlock relay, Key lock/unlock relay Tail & parking lamp (LH), Turn signal lamp, License lamp Tail & parking lamp (RH), Fog lamp relay, Switch illumination ETS control module (V6 3.5L), Fail safety relay Radiator fan relay, Condenser fan relay Front wiper motor, Wiper relay, Washer motor G200E01O-A EMISSION CONTROL SYSTEMS Emission Control System ............................................. 7-2 EGR System ................................................................. 7-3 Catalytic Converter ....................................................... 7-3 7 EMISSION CONTROL SYSTEMS EMISSION CONTROL SYSTEM H010A03O-AAT Your Hyundai is equipped with an emission control system to meet all requirements of the U.S. Environmental Protection Agency or Cali- fornia Air Resources Board. There are three emission control systems which are as follows. o 3.5 V6 - To prevent the vehicle from misfiring during dynamometer testing, turn the Traction Control System (TCS) off by pressing the TCS switch. After dynamometer testing is completed, turn the TCS system back on by pressing the TCS switch again. (1) Crankcase emission control system (2) Evaporative emission control system (3) Exhaust emission control system In order to assure the proper function of the emission control systems, it is recommended that you have your car inspected and main- tained by an authorized Hyundai dealer in ac- cordance with the maintenance schedule in this manual. Caution for the Inspection and Maintenance Test (V6 Vehicle with Traction Control Sys- tem) o 2.7 V6 - To prevent the vehicle from misfiring during dynamometer testing, disconnect the ABS connector in the engine compartment. After dynamom- eter testing is completed, erase the ABS/ TCS DTC (Diagnotic Trouble Code) with a GST (Generic Scan Tool) or Hi-Scan Pro. For more information, see shop manual (Wheel Speed Sensor). H010B01A-AAT 1. Crankcase Emission Control System The positive crankcase ventilation system is employed to prevent air pollution caused by blow-by gases being emitted from the crank- case. This system supplies filtered air to the crankcase through the air intake hose. Inside the crankcase, the fresh air mixes with blow-by gases, which then pass through the PCV valve and into the induction system. H010C01S-AAT 2. Evaporative Emission Control (Includ- ing ORVR: Onboard Refueling Vapor Recovery) System The Evaporative Emission Control System is designed to prevent fuel vapors from escaping into the atmosphere. (The ORVR system is designed to allow the vapors from the fuel tank to be loaded into a canister while refueling at the gas station, pre- venting the escape of fuel vapors into the atmosphere.) Canister Fuel vapors generated inside the fuel tank are absorbed and stored in the canister. When the engine is running, the fuel vapors absorbed in the canister are drawn into the induction system through the purge control solenoid valve. Purge Control Solenoid Valve (PCSV) The purge control solenoid valve is controlled by the Engine Control Module (ECM); when the engine coolant temperature is low during idling, the PCSV closes so that evaporated fuel is not taken into the engine. After the engine warms- up during ordinary driving, the PCSV opens to introduce evaporated fuel to the engine. H010D01A-AAT 3. Exhaust Emission Control System The Exhaust Emission Control System is a highly effective system which controls exhaust emissions while maintaining good vehicle performace. EGR SYSTEM CATALYTIC CONVERTER H010E01Y-AAT (If installed) H020A01A-AAT This system helps reduce nitrogen oxides by recirculating a part of the exhaust gas into the engine, thereby reducing cylinder combustion temperature, which results in lower output of oxides of nitrogen. Catalytic Converter H020A01O All Hyundai vehicles are equipped with a mono- lith type three-way catalytic converter to re- duce the carbon monoxide, hydrocarbons and nitrogen oxides contained in the exhaust gas. Exhaust gases passing through the catalytic converter cause it to operate at a very high temperature. The introduction of large amounts of unburned gasoline into the exhaust may cause the catalytic converter to overheat and create a fire hazard. This risk may be reduced by observing the following: EMISSION CONTROL SYSTEMS WARNING: o Use unleaded fuel only. o Maintain the engine in good operating condition. Extremely high catalytic con- verter temperatures can result from im- proper operation of the electrical, igni- tion or multiport electronic fuel injec- tion. o If your engine stalls, pings, knocks, or is hard to start, have your Hyundai dealer inspect and repair the problem as soon as possible. o Avoid driving with a very low fuel level. Running out of gasoline may cause the engine to misfire and result in damage to the catalytic converter. o Avoid idling the engine for periods longer than 10 minutes. o The vehicle should not be pushed or pulled to get started. This may cause the catalytic converter to overheat and cre- ate a fire hazard. o Do not touch the catalytic converter or any other part of the exhaust system while the catalytic converter is hot. Shut off the engine, wait for at least one hour before touching the catalytic converter or any other part of the exhaust system. o Remember that your Hyundai dealer is your best source of assistance. 7 EMISSION CONTROL SYSTEMS WARNING: o Do not stop your Hyundai over any com- bustible material such as grass, paper, leaves or rags. These materials might contact the hot catalytic converter and a fire might result. CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS Vehicle Identification Number (VIN) .............................. 8-2 Engine Number ............................................................. 8-2 Tire Information ............................................................. 8-2 Recommended Inflation Pressures ............................... 8-3 Tire Sidewall Labeling ................................................... 8-4 Tire Terminology and Definitions ................................... 8-6 Snow Tires .................................................................... 8-8 Tire Chains.................................................................... 8-9 Tire Rotation.................................................................. 8-9 Tire Balancing ............................................................... 8-9 Tire Traction ................................................................ 8-10 When to Replace Tires ............................................... 8-10 Tire Maintenance ........................................................ 8-11 Spare Tire and Tools................................................... 8-11 Warranties for Your Hyundai Vehicle .......................... 8-12 Consumer Information ................................................. 8-12 Reporting Safety Defects ............................................ 8-15 Binding Arbitration of Warranty Claims ....................... 8-15 8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS ENGINE NUMBER VEHICLE IDENTIFICATION NUMBER (VIN) I010A01O-AAT I010B01A-AAT 2.7 V6 I010A01O The vehicle identification number (VIN) is the number used in registering your car and in all legal matters pertaining to its ownership, etc. It can be found in three different places on your car: 3.5 V6 I010B01B TIRES I020A02A-AAT TIRE INFORMATION The tires supplied on your new Hyundai are chosen to provide the best perfor- mance for normal driving. If you ever have questions about your tire warranty and where to obtain ser- vice, see the tire manufacture's booklet included with your vehicle's Owner's Manual Literature Kit. 1. On the bulkhead between the engine and passenger compartments. 2. On the left top side of the instrument panel where it can be seen by looking down through the windshield. 3. On the lower side of the center pillar outer panel. The engine number is stamped on the engine block as shown in the drawing. I010B01L CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS I030A01JM-AAT RECOMMENDED INFLATION PRES- SURES I030A01O Tire label located on the driver's side of the center pillar outer panel gives the cold tire pressures recommended for your vehicle with the original tire size, the number of people that can be in your vehicle and vehicle capacity weight. I030A02O These pressures were chosen to pro- vide the most satisfactory combination of ride comfort, tire wear and stability under normal conditions. Tire pressures should be checked at least monthly. Proper tire inflation pressures should be maintained for these reasons: WARNING: o Lower-than-recommended tire pressures cause uneven tread wear, poor handling, poor fuel economy or tire failure. o Higher-than-recommended tire pressures can cause poor han- dling, uneven tread wear or tire failure. CAUTION: Always observe the following: o Check pressures when the tires are cold. (After the vehicle has been parked for at least three hours or hasn't been driven more than 1 mile (1.6 km) since starting up.) 8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS o Check the pressure of your spare tire each time you check the pres- sure of other tires. o Never overload your vehicle. Be especially careful about overload- ing if you equip your vehicle with a luggage rack. o Worn, old tires can cause acci- dents. If your tread is badly worn, or if your tires have been dam- aged, replace them. I035A01JM-AAT CHECKING TIRE INFLATION PRES- SURE Check your tires once a month or more. Also, check the tire pressure of the spare tire. How to Check Use a good quality gauge to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they're underinflated. Check the tire's inflation pressure when the tires are cold. - "Cold" means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure mea- surement. If the cold tire inflation pres- sure matches the recommended pres- sure on the tire and loading information label, no further adjustment is neces- sary. If the pressure is low, add air until you reach the recommended amount. If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pres- sure with the tire gauge. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture. I030B01O-AAT TIRE SIDEWALL LABELING 5, 6 I030B04JM Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamen- tal characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall. CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 1. Manufacturer or Brand name o Manufacturer or Brand name is shown. 2. Tire size (example: P225/70R16 101T) o The "P" indicates the tire is de- signed for passenger vehicles. o Three-digit number (225): This num- ber gives the width in millimeters of the tire from sidewall edge to sidewall edge. o Two-digit number (70): This num- ber, known as the aspect ratio, gives the tire's ratio of height to width. o R: The "R" stands for radial. o Two-digit number (16): This num- ber is the wheel or rim diameter in inches. o Three digit number (101): This num- ber is the tire's load index. It is a measurement of how much weight each tire can support. o T: Speed Rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time. The ratings range from "A" to "Z" (98 to 186 MPH). 3. TIN (Tire Identification Number) for new tire (example: DOT XX XX XXX XXXX) o DOT: Abbreviation for the "Depart- ment of Transportation". The sym- bol can be placed above, below or to the left or right of the Tire Iden tification Number. It indicates the tire is in compliance with the U.S. Department of Transportation Mo- tor Vehicle Safety Standards. o 1st two-digit code: Manufacturer's identification mark o 2nd two-digit code: Tire size o 3rd three-digit code: Tire type code (Optional) o 4th four-digit code: Date of Manu- facture o Four numbers represent the week and year the tire was built. For example, the numbers 3105 means the 31st week of 2005. 4. Tire ply composition and material The number of layers or plies of rubbercoated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which in- clude steel, nylon, polyester, and others. The letter "R" means radial ply construction; the letter "D" means diagonal or bias ply construction; and the letter "B" means belted-bias ply construction. 5. Maximum permissible inflation pressure This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible inflation pressure. Refer to the Tire and Loading Information label for recommended inflation pres- sure. 8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 6. Maximum load rating This number indicates the maximum load in kilograms and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire. 7. Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three perfor- mance factors: treadwear, traction and temperature resistance. For more information, see Uniform Tire Qual- ity Grading on page 8-13. I030D01JM-AAT TIRE TERMINOLOGY AND DEFINI- TIONS Air Pressure: The amount of air inside the tire pressing outward on the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accesso- ries. Some examples of optional ac- cessories are, automatic transmission, power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread. Cold Tire Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. Curb Weight: This means the weight of a motor vehicle with standard and op- tional equipment including the maxi- mum capacity of fuel, oil and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Depart- ment of Transportation motor vehicle safety standards. The DOT code in- cludes the Tire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand and date of production. GVWR: Gross Vehicle Weight Rating GAWR FRT: Gross Axle Weight Rating for the front Axle. GAWR RR: Gross Axle Weight Rating for the rear axle. CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS Intended Outboard Sidewall: The side of an asymmetrical tire, that must al- ways face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Load Index: An assigned number rang- ing from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire may be inflated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rat- ing for a tire at the maximum permis- sible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehicle capacity weight; and production options weight. Normal Occupant Weight: The num- ber of occupants a vehicle is designed to seat multiplied by 150 pounds (68 kg). Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of an asymmetrical tire that has a particu- lar side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering or bears manufacturer, brand and or model name molding that is higher or deeper than the same mold- ings on the other sidewall of the tire. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. Radial Ply tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire upon which the tire beads are seated. Sidewall: The portion of a tire between the tread and the bead. Speed Rating: An alphanumeric code assigned to a tire indicating the maxi- mum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called "wear bars," that show across the tread of a tire when only 2/32 inch of tread remains. UTQGS: Uniform Tire Quality Grading Standards, a tire information system that provides consumers with ratings for a tire's traction, temperature and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. 8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS Vehicle Capacity Weight: The number of designated seating positions multi- plied by 150 lbs. (68 kg) plus the rated cargo and luggage load. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb and accessory weight plus maximum occupant and cargo weight. Vehicle Normal Load on the Tire: That load on an individual tire that is determined by distributing to each axle its share of the curb weight, accessory weight, and normal occupant weight and dividing by 2. Vehicle Placard: A label permanently attached to a vehicle showing the origi- nal equipment tire size and recom- mended inflation pressure. I040A01O-AAT SNOW TIRES If you equip your car with snow tires, they should be the same size and have the same load capacity as the original tires. Snow tires should be installed on all four wheels; otherwise, poor han- dling may result. Snow tires should carry 4 psi (28 kPa) more air pressure than the pressure recommended for the standard tires on the tire label on the driver's side of the center pillar , or up to the maximum pressure shown on the tire sidewall, whichever is less. Do not drive faster than 75 mph (120 km/h) when your car is equipped with snow tires. I040B01JM-AAT ALL SEASON TIRES Hyundai specifies all season tires on some models to provide good perfor- mance for use all year round, including snowy and icy road conditions. All sea- son tires are identified by ALL SEASON and/or M+S (Mud and Snow) on the tire sidewall. Snow tires have better snow traction than all season tires an may be more appropriate in some areas. I040C01JM-AAT SUMMER TIRES Hyundai specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially reduced in snow and ice. Summer tires do not have the tire traction rating M+S (Mud and Snow) on the tire side wall. If you plan to operate your vehicle in snowy or icy conditions, Hyundai recommends the use of snow tires or all season tires on all four wheels. CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS I060A01O-AAT TIRE ROTATION Spare tire HA1409 Tires should be rotated every 7,500 miles (12,000 km). If you notice that tires are wearing unevenly between ro- tations, have the car checked by a Hyundai dealer so the cause may be corrected. After rotating, adjust the tire pressures and be sure to check wheel nut torque. CAUTION: Do not mix bias-ply and radial-ply under any circumstances. This may cause dangerous handling charac- teristics. I070A01A-AAT TIRE BALANCING A tire that is out of balance may affect handling and tire wear. The tires on your Hyundai were balanced before the car was delivered but may need balancing again during the years you own the car. Whenever a tire is dismounted for re- pair, it should be rebalanced before being reinstalled on the car. I050A01O-AAT TIRE CHAINS Tire chains, if necessary, should be installed on the front wheels. If your vehicle is equipped with 4WD (four wheels drive), be sure to install the chains on all wheels. Be sure that the chains are installed in accordance with the manufacturer's instructions. To minimize tire and chain wear, do not continue to use tire chains when they are no longer needed. WARNING: o Drive at lower speeds when driving on roads covered with snow or ice. o Use the SAE "S" class or wire & plastic chains. o If you hear noise caused by chains contacting the body, retighten the chain to avoid contact with the vehicle body. o To prevent body damage, retighten the chains after driving 0.3 ~ 0.6 miles. 8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 10 I080A01A-AAT TIRE TRACTION Tire traction can be reduced if you drive on worn tires, tires that are improperly inflated or on slippery road surfaces. Tires should be replaced when tread wear indicators appear. To reduce the possibility of losing control, slow down whenever there is rain, snow or ice on the road. ! WARNING: o Driving on worn-out tires is dan- gerous! Worn-out tires can cause loss of braking effectiveness, steering control and traction. When replacing tires, never mix radial and bias ply tires on the same car. If you replace radial tires with bias- ply tires, they must be installed in sets of four. o Wheels that do not meet Hyundai's dimensional specifications may fit poorly and result in damage to the vehicle, including broken wheel studs. I090A02JM-AAT WHEN TO REPLACE TIRES 0.06 in. (1.6 mm) Tread wear indicator HSM5013 The original tires on your car have tread wear indicators. The location of tread wear indicators is shown by the "TWI" or " " marks, etc., The tread wear indicators appear when the tread depth is 0.06 in. (1.6 mm). The tire should be replaced when these appear as a solid bar across two or more grooves of the tread. Always replace your tires with those of the recommended size. If you change wheels, the new wheel's rim width and offset must meet Hyundai specification. 8 11 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS I090B01O-AAT TIRE MAINTENANCE In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel align- ment. When you have new tires installed, make sure they are balanced. This will increase vehicle ride comfort and tire life. Additionally, a tire shoud always be rebalanced if it is removed from the wheel. SPARE TIRE AND TOOLS I100A02E-AAT D060B01O Your Hyundai is delivered with the fol- lowing: Spare tire and wheel Wheel nut wrench, Wrench bar Jack WARNING: o Your vehicle is equipped with tires designed to provide for safe ride and handling capability. Do not use a size and type of tire and wheel that is different from the one that is originally installed on your vehicle. It can affect the safety and performance of your vehicle, which could lead to handling fail- ure or rollover and serious injury. When replacing the tires, be sure to equip all four tires with the tire and wheel of the same size, type, tread, brand and load-carrying capacity. If you nevertheless de- cide to equip your vehicle with any tire/wheel combination not rec- ommended by Hyundai for off- road driving, you should not use these tires for highway driving. 8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS WARRANTIES FOR YOUR HYUNDAI 12 VEHICLE I110A01A-AAT SHOP MANUAL A Hyundai Shop Manual is available from your authorized Hyundai dealer. It's written for pro- fessional technicians, but is simple enough for most mechanically-inclined owners to under- stand. I120A02A-AAT o New vehicle 60 Months/60,000 Miles Limited Warranty. o New vehicle 120 Months/100,000 Miles Lim- ited Powertrain Warranty (original owner only). o Anti-Perforation Limited Warranty o Emission Defect Warranty - Federal Vehicle o California Emission Control System War- ranty (if applicable) o Emission Performance Warranty Federal o Replacement Parts and Accessories Lim- vehicle ited Warranty NOTE: Detailed warranty information is provided in your Hyundai Owner's Handbook. CONSUMER INFORMATION I130A01A-AAT This consumer information has been prepared in accordance with regulations issued by the National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Hyundai automobiles with infor- mation on uniform tire quality grading. Your Hyundai dealer will help answer any questions you may have as you read this information. CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 13 Traction AA, A, B, C - The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pave- ment as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction per- formance. ! WARNING: The traction grade assigned to this tire is based on straight-ahead brak- ing traction tests, and does not in- clude acceleration, cornering, hy- droplaning, or peak traction charac- teristics. Temperature A, B, C - The tempera- ture grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under con- trolled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. I130B04A-AAT Tire Quality Grading Department of Transportation quality grades - All passenger vehicle tires must conform to Federal Safety Stan- dards in addition to these grades. These quality grades are molded on the sidewall. Treadwear - The treadwear grade is a comparative rating based on the wear rate of the tire when tested under con- trolled conditions on a specified gov- ernment test course. For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to varia- tions in driving habits, service prac- tices and differences in road character- istics and climate. 8 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS 14 ! WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Exces- sive speed, underinflation, or exces- sive loading, either separately or in combination, can cause heat buildup and possible tire failure. Uniform Tire Quality Grading - Qual- ity grades can be found on the tire sidewall between the tread shoulder and the maximum section width. For example : Treadwear 200 Traction AA Tempera- ture A I130D03A-AAT Hyundai motor vehicles are designed and manu- factured to meet or exceed all applicable safety standards. Southern Region: Alabama, Arkansas, Florida, Georgia, Louisiana, Mississippi, North Caro- lina, South Carolina, Oklahoma, Tennessee, Texas. For your safety, however, we strongly urge you to read and follow all directions in this Owner's Manual, particularly the information under the headings "NOTE", "CAUTION" and "WARN- ING". If, after reading this manual, you have any questions regarding the operation of your ve- hicle, please contact your nearest Hyundai Motor America Regional Office as listed below: Eastern Region : Connecticut, Delaware, Maine, Maryland, Massachusetts, New Hamp- shire, New Jersey, New York, Pennsylvanina, Rhode Island, Vermont, Virginia, West Virginia. Eastern Region 1100 Cranbury South River Road Jamesburg, NJ 08831 (800) 633-5151 Southern Region 270 Riverside Parkway, Suite A Austell, GA 30168 (800) 633-5151 Central Region: Illinois, Indiana, Missouri, lowa, Kansas, Kentucky, Michigan, Minnesota, Ne- braska, North Dakota, South Dakota, Ohio, Wisconsin. Central Region 1705 Sequoia Drive Aurora, Illinois 60506 (800) 633-5151 Western Region: Alaska, Hawaii, Arizona, Cali- fornia, Colorado, ldaho, Montana, Nevada, New Mexico, Oregon, Texas, Utah, Washington, Wyoming. Western Region 10550 Talbert Avenue P.O.Box 20850 Fountain Valley, California 92728-0850 (800) 633-5151 8 15 CONSUMER INFORMATION, REPORTING SAFETY DEFECTS & BINDING ARBITRATION OF WARRANTY CLAIMS REPORTING SAFETY DEFECTS BINDING ARBITRATION I130C01A-AAT If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying HYUNDAI MOTOR AMERICA. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy cam- paign. However, NHTSA cannot become involved in individual problems between you, your dealer, or HYUNDAI MOTOR AMERICA. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-888-327- 4236 or write to: NHTSA, U.S. Department of Transportation, Washington. D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline. I140A01A-AAT Any claim or dispute you may have related to your vehicle's warranty or the duties contemplated under the warranty, including claims related to the refund or partial refund of your vehicle's purchase price (excluding personal injury or prod- uct liability claims), shall be resolved by binding arbitration. Binding arbitra- tion shall be administered by and through the National Arbitration Forum (NAF) or the American Arbitration Association (AAA), under the Code of Procedure of the entity you select. You will not be responsible for paying filing and hearing fees above $275.00. All other arbitration costs shall be borne by Hyundai Motor America. You are not responsible to pay any of the costs Hyundai incurs. This Binding Arbitration Agreement shall not deprive you of any remedies avail- able to you under applicable law. The parties are waiving their right to seek remedies in court, including the right to a jury trial. This Binding Arbitration Agreement shall be governed by and interpreted under the Federal Arbitration Act, 9 U.S.C. sections 1-16. Judgment upon any award may be entered in any court having jurisdiction. You may revoke this Arbitration Agree- ment by (1) written notice or (2) elec- tronic notice. Written notice must be delivered (via certified mail) to Hyundai Motor America, Attn: Consumer Af- fairs, 10550 Talbert Avenue, P.O. Box 20849, Fountain Valley, CA 92728-0849. Electronic notice must be submitted at the following website address: http:// warranty-arbitration.hyundaiUSA.com. Notice must be received within 90 days after you purchase your vehicle. INDEX 10 10 10 INDEX Advanced Supplemental Restraint(AIRBAG) System(SRS) ........... 1-34 Air Cleaner Filter ............................................................................... 6-11 Air Conditioning Care .............................................................................................. 6-16 Filter .................................................................................. 1-108, 6-17 Operation ............................................................................ 1-99, 6-16 Switch ........................................................................................... 1-98 Antenna .......................................................................................... 1-138 Ashtray .............................................................................................. 1-67 Audio System Cassete tape player operation (D-285) ................................... 1-121 Compact disc player operation (H260) .................................... 1-114 Compact disc player operation (D-285) ................................... 1-125 Compact disc player operation (D-295) ................................... 1-131 Stereo radio operation (H260) .................................................. 1-111 Stereo radio operation (D-285) ................................................ 1-118 Stereo radio operation (D-295) ................................................ 1-128 Azimuth Compass ............................................................................. 1-63 Battery ..................................................................................... 2-22, 6-22 Binding Arbitration ............................................................................. 8-15 Brake Anti-lock brake system(ABS) ...................................................... 2-12 Brake traction control system (BTCS) ........................................ 2-13 Checking the brakes .................................................................... 6-15 Fluid .............................................................................................. 6-15 Pedal clearance ........................................................................... 6-29 Pedal free-play ............................................................................. 6-19 Practices ...................................................................................... 2-19 Breaking-In your New Hyundai .......................................................... 1-3 Care of Cassette Tapes ................................................................ 1-135 Care of Discs ................................................................................. 1-135 Cargo Security Screen ..................................................................... 1-81 Catalytic Converter ............................................................................. 7-3 Center Console Box .......................................................................... 1-73 Child-Protector Rear Door Lock ......................................................... 1-7 Child Restraint System ..................................................................... 1-26 Installing a child restraint seat with the "Tether Anchorage" system ..................................................... 1-28 Securing the child restraint seat with the "ISOFIX" system ....... 1-29 Cigarette Lighter ................................................................................ 1-66 Clock ................................................................................................. 1-63 Combination Light Auto light ....................................................................................... 1-59 Headlight flasher .......................................................................... 1-59 Headlight switch ........................................................................... 1-58 High-beam switch ........................................................................ 1-58 Lane change signal ...................................................................... 1-58 Parking light auto off .....................................................................1-58 Turn signal operation ................................................................... 1-57 Consumer Information ...................................................................... 8-12 Cooling Fans ..................................................................................... 6-23 INDEX 10 Corrosion protection Cleaning the interior ....................................................................... 4-5 Protecting your Hyundai from corrosion ....................................... 4-2 Washing and waxing ...................................................................... 4-3 Cruise Control ................................................................................... 1-89 If the engine overheats .................................................................. 3-4 Number ........................................................................................... 8-2 Oil ................................................................................................... 6-5 Starting ........................................................................................... 2-5 Engine Exhaust Can Be Dangerous .................................................. 2-2 Defrosting / Defogging ................................................................... 1-101 Door Central door locks .......................................................................... 1-7 Door locks ...................................................................................... 1-4 Front door edge warning light ...................................................... 1-88 Locking, unlocking front door with a key ...................................... 1-5 Drink Holder ...................................................................................... 1-67 Drive Belts ......................................................................................... 6-19 Driving Driving for economy ..................................................................... 2-20 Smooth cornering ......................................................................... 2-21 Winter driving ............................................................................... 2-21 Emission Control System ................................................................... 7-2 Engine Before starting the engine .............................................................. 2-3 Compartment (2.7 V6) ................................................................... 6-2 Compartment (3.5 V6) ................................................................... 6-3 Coolant ........................................................................................... 6-8 Coolant temperature gauge ......................................................... 1-52 Fan Speed Control ............................................................................ 1-93 Floor Mat Anchor ..............................................................................1-86 Fog Light Front ............................................................................................. 1-62 Front Seats Adjustable front seats ..................................................................1-12 Adjustable headrests ................................................................... 1-13 Adjusting seat forward and rearward .......................................... 1-12 Adjusting seatback angle ............................................................. 1-12 Fuel Auto fuel cut switch ...................................................................... 1-84 Capacity ......................................................................................... 9-2 Gauge ........................................................................................... 1-52 Recommendations ......................................................................... 1-2 Fuel Filler Lid Remote release ............................................................................ 1-84 Full Traction Control System (FTCS) .............................................. 2-14 Full-time 4WD Operation .................................................................. 2-16 Fuses ................................................................................................ 6-20 10 INDEX General Checks .................................................................................. 6-4 Glove Box .......................................................................................... 1-72 Hazard Warning System .................................................................. 1-62 Heating and Cooling Control ............................................................. 1-92 Heating and Ventilation Air flow control .............................................................................. 1-94 Air intake control switch ...............................................................1-93 Bi-level heating ............................................................................. 1-98 Defrosting / Defogging .............................................................. 1-101 Fan speed control (Blower control) ............................................. 1-93 Temperature control .................................................................... 1-97 High-Mounted Rear Stop Light ......................................................... 1-83 Homelink Mirror ................................................................................. 1-76 Hood Release .................................................................................... 1-85 Horn ................................................................................................. 1-88 Ignition Switch ...................................................................................... 2-4 Instrument Cluster and Indicator Lights ........................................... 1-46 Instrument Panel Light Control (Rheostat) ....................................... 1-65 Interior Light ....................................................................................... 1-71 Jump Starting ...................................................................................... 3-3 Keys ................................................................................................... 1-3 If you lose your keys ................................................................... 3-15 Positions ......................................................................................... 2-4 Light Bulbs Replacement .................................................................. 6-26 Limited-Slip Differential ...................................................................... 2-19 Luggage Compartment Light ............................................................ 1-81 Luggage Net ...................................................................................... 1-82 Maintenance Intervals Explanation of scheduled maintenance items ............................... 5-7 Maintenance under severe usage conditions ............................... 5-6 Scheduled maintenance ................................................................ 5-4 Service requirements .................................................................... 5-2 Mirrors Day-night inside rearview mirror ................................................. 1-76 Outside rearview mirror ............................................................... 1-73 Odometer / Trip Odometer ...............................................................1-53 Parking Brake .................................................................................... 1-80 Power Driver's Seat .......................................................................... 1-14 Power Outlet ...................................................................................... 1-66 Power Steering Fluid Level ............................................................... 6-23 INDEX 10 Rear Seat Adjusting seatback angle ............................................................. 1-17 Folding rear seatback and seat cushion .................................... 1-17 Rear Window Defroster Switch ........................................................ 1-62 Reporting Safety Defects ................................................................. 8-15 Risk of Rollover ................................................................................... 2-3 Roof Rack ......................................................................................... 1-83 Seat Front ............................................................................................. 1-12 Rear .............................................................................................. 1-17 Seat warmer ................................................................................. 1-16 Seat Belts 3-point system ............................................................................. 1-22 Pretensioner seat belt .................................................................. 1-32 Adjusting your seat belt ............................................................... 1-24 Care of seat belts ......................................................................... 1-21 Precautions .................................................................................. 1-19 Shop Manual ........................................................................................ 8-5 Sound Brake pad warning sound ............................................................ 1-51 Parking start warning sound ........................................................ 1-51 Spark Plugs ....................................................................................... 6-10 Spectacle Case ................................................................................. 1-72 Speedometer ..................................................................................... 1-53 Starting Procedure .............................................................................. 2-6 Steering Wheel Free play ................................................................. 6-18 Steering Wheel Tilt Lever ..................................................................1-87 Stereo Sound System .................................................................... 1-108 Sunroof .............................................................................................. 1-69 Sun Visor ........................................................................................... 1-86 Tachometer ....................................................................................... 1-53 Tail Gate ............................................................................................ 1-80 Tail gate window ........................................................................... 1-81 Theft-Alarm System ............................................................................ 1-8 Tires Balancing ........................................................................................ 8-9 Chains ............................................................................................ 8-9 Changing a flat tire ......................................................................... 3-6

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2005 Hyundai Santa FE Owners Manual