2005 Hyundai Santa FE Owners Manual

3. SRS control module

NOTE: o Both the driver's and front passenger's pre-tensioner seat belts will be activated in certain frontal collisions. The pre- tensioner seat belts can be activated alone or, where the frontal collision is severe enough, together with the airbags. The pre-tensioners will not be activated if the seat belts are not being worn at the time of the collision.

o When the pre-tensioner seat belts are activated, a loud noise may be heard and fine dust, which may appear to be smoke, may be visible in the passenger com- partment. These are normal operating conditions and are not hazardous.

HXG229

When the vehicle stops suddenly, or if the occupant tries to lean forward too quickly, the seat belt retractor will lock into position. In certain frontal collisions, the pre-tensioner will activate and pull the seat belt into tighter contact against the occupant's body.

FEATURES OF YOUR HYUNDAI

33

! WARNING:

o Improper handling of the pre-tensioner seat belt assemblies, and failure to heed the warnings to not strike, modify, in- spect, replace, service or repair the pre- tensioner seat belt assemblies may lead to improper operation or inadvertent activation and serious injury.

o Always wear the seat belts when driving

or riding in a motor vehicle.

WARNING:

o Pre-tensioners are designed to operate only one time. After activation, pre- tensioner seat belts must be replaced. All seat belts, of any type, should always be replaced after they have been worn during a collision.

o The pre-tensioner seat belt assembly mechanisms become hot during activa- tion. Do not touch the pre-tensioner seat belt assemblies for several minutes after they have been activated.

o Do not attempt to inspect or replace the pre-tensioner seat belts yourself. This must be done by an authorized Hyundai dealer.

o Do not strike the pre-tensioner seat belt

assemblies.

o Do not attempt to service or repair the pre-tensioner seat belt system in any manner.

o Although it is harmless, the fine dust may cause skin irritation and should not be breathed for prolonged periods. Wash your hands and face thoroughly after an accident in which the pre-tensioner seat belts were activated.

CAUTION:

o The sensor that activates the SRS airbag is connected with the pre-tensioner seat belt. The SRS airbag warning light on the instrument panel will illuminate for approximately 6 seconds after the igni- tion key has been turned to the "ON" position, and then it should turn off.

AIR BAG

o If the pre-tensioner seat belt is not work- ing properly, this warning light will illu- minate even if there is no malfunction of the SRS airbag system. If the SRS airbag warning light does not illuminate when the ignition key is turned to "ON" or if it remains illuminated after approximately 6 seconds, or if it illumi- nates while the vehicle is being driven, please have an authorized Hyundai dealer inspect the pre-tensioner seat belts and SRS airbag system as soon as possible.

1FEATURES OF YOUR HYUNDAI 34

ADVANCED SUPPLEMENTAL RESTRAINT (AIRBAG) SYSTEM (SRS)

B240A01O-AAT Driver's Airbag

B240A01O

Your Hyundai is equipped with an advanced Supplemental Restraint (Airbag) System. The indications of the system's presence are the letters "SRS AIRBAG" embossed on the airbag pad cover in the steering wheel and the passenger's side front panel pad above the glove box.

The Hyundai SRS consists of airbags installed under the pad covers in the center of the steering wheel and the passenger's side front panel above the glove box. The purpose of the SRS is to provide the vehicle's driver and/or the front passenger with additional protection than that offered by the seat belt system alone in case of a frontal impact of sufficient severity.

The SRS uses sensors to gather information about the driver's and front passenger's seat position, the driver's and front passenger's seat belt usage and impact severity.

The driver's and front passenger's seat track position sensors, which are installed on the seat track, determine if the seats are fore or aft of a reference position. The seat belt buckle sen- sors determine if the driver and front passenger's seat belts are fastened. These sensors provide the ability to control the SRS deployment based on how close the driver's seat is to the steering wheel, how close the passenger's seat is to the instrument panel, whether or not the seat belts are fastened, and how severe the impact is.

The advanced SRS offers the ability to control the airbag inflation with two levels. A first stage level is provided for moderate-severity impacts. A second stage level is provided for more severe impacts.

According to the impact severity, seating posi- tion and seat belt usage, the SRSCM(SRS Control Module) controls the airbag inflation. Failure to properly wear seat belts can increase the risk or severity of injury in an accident.

Additionally, your Hyundai is equipped with an occupant classification system in the front passenger's seat. The occupant classification system detects the presence of a passenger in the front passenger's seat and will turn off the front passenger's airbag under certain condi- tions. For more detail, see "Occupant Classifi- cation System" later in this section.

CAUTION:

AIR BAG

If a seat track position sensor or an occu- pant classification system is not working properly, the SRS airbag warning light on the instrument panel will illuminate be- cause the SRS airbag warning light is con- nected with the seat track position sensor and the occupant classification system. If the SRS airbag warning light does not illu- minate when the ignition key is turned to the "ON" position, remains illuminated af- ter approximately 6 seconds when the igni- tion key is turned to the "ON" position, or if it illuminates while the vehicle is being driven, have an authorized Hyundai dealer inspect the seat track position sensor and the advanced SRS airbag system as soon as possible.

FEATURES OF YOUR HYUNDAI

35

WARNING:

o Front airbags are not intended to deploy in side-impact, rear-impact or rollover crashes. In addition, front airbags will not deploy in frontal crashes below the deployment threshold.

Rear impact

Side Impact

Rollover

B240D01O o The driver should sit back as far as possible while still maintaining control of the vehicle. If you are sitting too close to the airbag, it can cause death or seri- ous injury when it inflates.

WARNING:

o As its name implies, the SRS is designed to work with, and be supplemental to the driver's and the passenger's three point seat belt systems and is not a substitute for them. Therefore, your seat belts must be worn at all times. The airbags deploy only in certain frontal impact conditions severe enough to cause significant in- jury to the vehicle occupants.

o Sitting too close to a front airbag can result in serious or fatal injury if the front airbags inflate. Always sit as far back from airbags as possible.

o Ignoring the SRS airbag warning light can result in serious or fatal injury if the airbags, occupant classification system or pre-tensioners do not work properly. Have your car checked by a dealer as soon as possible if the SRS airbag warning light alerts you to a potential problem.

o The SRS is designed to deploy the front airbags only when an impact is suffi- ciently severe and when the impact angle is less than 30° from the forward longi- tudinal axis of the vehicle. The front airbags will not deploy in side, rear or rollover impacts. Additionally, the airbags will only deploy once. Seat belts must be worn at all times.

WARNING:

o Modification to the seat structure can adversely affect the seat track position sensor and cause the airbag to deploy at a different level than should be pro- vided.

o Do not place any objects underneath the front seats as they could damage the seat track position sensor or interfere with the occupant classification sys- tem.

o Do not place any objects that may cause magnetic fields near the front seat. These may cause a malfunction of the seat track position sensor.

NOTE: o Be sure to read information about the SRS on the labels provided in the front of the sun visor and in the glove box.

o Advanced airbags are combined with pre-tensioner seat belts to help provide enhanced occupant protection in fron- tal crashes. Front airbags are not in- tended to deploy in collisions in which sufficient protection can be provided by the pre-tensioner seat belt.

o If you are considering modification of your vehicle due to a disability, please contact the Hyundai Customer Assis- tance Center at 1-800-633-5151.

1FEATURES OF YOUR HYUNDAI 36

WARNING:

o No objects should be placed over or near the airbag modules on the steering wheel, instrument panel, and the front passenger's panel above the glove box, because any such object could cause harm if the vehicle is in a crash severe enough to cause the airbags to deploy. o If the airbags deploy, they must be re- placed by an authorized Hyundai dealer. o Do not tamper with or disconnect SRS wiring or other components of the SRS system. Doing so could result in injury, due to accidental deployment of the airbags or by rendering the SRS inopera- tive.

o Even though your vehicle is equipped with the occupant classification sys- tem, do not install a child restraint sys- tem in the front passenger seat position. A child restraint system must never be placed in the front seat. The infant or child could be severely injured or killed by an airbag deployment in case of an accident.

WARNING:

o Do not allow children to ride in the front passenger seat. If older children (teen- agers and older) must ride in the front seat, make sure they are always properly belted and the seat is moved back as far as possible.

o For maximum safety protection in all types of crashes, all occupants includ- ing the driver should always wear their seat belts whether or not an airbag is also provided at their seating position to minimize the risk of severe injury or death in the event of a crash. Do not sit or lean unnecessarily close to the airbag while the vehicle is in motion.

o Sitting improperly or out of position can result in serious or fatal injury in a crash. All occupants should sit upright with the seat back in an upright position, centered on the seat cushion with their seat belt on, legs comfortably extended and their feet on the floor until the ve- hicle is parked and the ignition key is removed.

o The SRS airbag system must deploy very rapidly to provide protection in a crash. If an occupant is out of position because of not wearing a seat belt, the airbag may forcefully contact the occupant causing serious or fatal injuries.

B240B01O-AAT SRS Components and Functions

2 7 10

11

7 9

B240B02O The SRS consists of the following components:

1. Driver's Airbag Module 2. Passenger's Airbag Module 3. Knee Bolster 4. Pre-tensioner Seat Belt 5. Front Impact Sensor 6. Driver's and Front Passenger's Seat Belt

7. Driver's and Front Passenger's Seat Track

Buckle Sensors

Position Sensors

8. SRS Service Reminder Indicator (SRI) 9. SRS Control Module (SRSCM) 10.Occupant Classification System

(Front passenger's seat only) 11.Passenger Airbag Off Indicator

(Front passenger's seat only)

FEATURES OF YOUR HYUNDAI

37

B240B02L

Upon deployment, tear seams molded directly into the pad covers will separate under pres- sure from the expansion of the airbags. Further opening of the covers then allows full inflation of the airbags.

B240B03L A fully inflated airbag, in combination with a properly worn seat belt, slows the driver's or the passenger's forward motion, reducing the risk of head and chest injury.

After complete inflation, the airbag immediately starts deflating, enabling the driver to maintain forward visibility, and the ability to steer or operate other controls.

The SRSCM continually monitors all elements while the ignition is "ON" to determine if a frontal or near-frontal impact is severe enough to require airbag deployment or pre-tensioner seat belt deployment.

The SRS service reminder indicator (SRI) on the instrument panel will illuminate for about 6
seconds after the ignition key is turned to the "ON" position or after the engine is started, after which the SRI should go out.

B240B01L

The airbag modules are located both in the center of the steering wheel and in the front passenger's panel above the glove box. When the SRSCM detects a sufficiently severe impact to the front of the vehicle, it will automatically deploy the front airbags.

1FEATURES OF YOUR HYUNDAI 38

Passenger's Airbag

Passenger's Airbag

B240B01O

B240B05L

CAUTION:

When installing a container of liquid air freshener inside the vehicle, do not place it near the instrument cluster nor on the in- strument panel surface. If there is any leak- age from the air freshener onto these areas (instrument cluster, instrument panel or air ventilator), it may damage these parts. If the liquid from the air freshener does leak onto these areas, wash them with water immedi- ately.

! WARNING:

o When the SRS is activated, there may be a loud noise and fine dust will be re- leased throughout the vehicle. These conditions are normal and are not haz- ardous. However, the fine dust generat- ed during airbag deployment may cause skin irritation. Wash all exposed skin areas thoroughly with lukewarm water and a mild soap after an accident in which the airbags were deployed.

WARNING:

o The SRS can function only when the ignition key is in the "ON" position. If the SRS SRI does not illuminate, or contin- uously remains on after illuminating for about 6 seconds when the ignition key is turned to the "ON" position, or after the engine is started, illuminates while driving, the SRS is not working properly. If this occurs, have your vehicle immedi- ately inspected by your Hyundai dealer. o Before you replace a fuse or disconnect a battery terminal, turn the ignition key to the "LOCK" position and remove the ignition key. Never remove or replace the airbag related fuse(s) when the ignition key is in the "ON" position. Failure to heed this warning will cause the SRS SRI to illuminate.

NOTE: Your vehicle's Supplemental Restraint Sys- tem Control Module is equipped a record- ing device which may record the use of the seat belt restraint system by the driver and front passenger in certain collisions.

B990A01O-AAT OCCUPANT CLASSIFICATION SYSTEM

Your vehicle is equipped with an occupant classification system in the front passenger's seat. The Occupant Classification system is de- signed to detect the presence of a properly- seated front passenger and determine if the passenger's front airbag should be enabled (may inflate) or not. The driver's front airbag is not affected or controlled by the Occupant Classification system.

B240C01O If the front passenger seat is occupied by a person, and the system determines to be of adult size and he/she sits properly (sitting up- right with the seat back in an upright position, centered on the seat cushion with their seat belt on, legs comfortably extended and their feet on

the floor), the "PASSENGER AIR BAG OFF" indicator will be turned off and the front passenger's airbag will be able to inflate, if necessary, in frontal crashes. You will find the "PASSENGER AIR BAG OFF" indicator on the center facia panel. This system detects the conditions 1~4 in the following table and activates or deactivates front passenger airbags based on these conditions.

Condition and operation in the front pas- senger occupant classification system

Condition

detected by the occupant classification

system

1. Adult*1
2. Child*2 or

child restraint system*3

3. Unoccupied 4. There is a

malfunction in the system

"Passenger air bag off" indicator light

SRS

Front

warning

passenger

light

airbag

Off

On

On

Off

Off

Off

Off

Activated

Deactivated

Deactivated

On

Activated

*1) The system judges a person of adult size as an adult. When a smaller adult sits in the front passenger seat, the system may recognize him/her as a child depending on his/her physique and posture.

FEATURES OF YOUR HYUNDAI

39

*2) Do not allow children to ride in the front passenger seat. When a larger child who has outgrown a child restraint system sits in the front passenger seat, the system may recognize him/her as an adult depending on his/her physique or posture.

*3) Never install a child restraint system on the

front passenger seat.

In order that the system detects the condi- tions correctly, do not do any of the follow- ing.

o Put a heavy load in the front passenger seat.

B990A08O

1FEATURES OF YOUR HYUNDAI 40

Normal position

B990A01O When an adult is seated in the front passenger seat, if the "PASSENGER AIR BAG OFF" indi- cator is on, turn the ignition key to "LOCK" and ask the passenger to sit properly (sitting upright with the seat back in an upright position, cen- tered on the seat cushion with their seat belt on, legs comfortably extended and their feet on the floor). Restart the engine and have the person in the position for about 30 seconds. This will allow the system to detect the person and to enable the passenger airbag. If the "PASSEN- GER AIR BAG OFF" indicator is still on, ask the passenger to move to the rear seat.

B990A03O o Excessively recline the front passenger

seatback.

- Lean on on the center console. - Sit on one side of the front passenger seat.

B990A07O

o Sit with hips shifted towards the front of the

seat.

- Place feet on the dashboard.

B990A02O

B990A05O

FEATURES OF YOUR HYUNDAI

41

WARNING:

o Do not modify or replace the front pas- senger seat. Don't place anything on or attach anything to the front passenger seat. This can adversely affect the occu- pant classification system.

o Do not sit on sharp objects such as tools when occupying the front passenger seat. This can adversely affect the occu- pant classification system.

o Do not use accessory seat covers on the

front seats.

o Accident statistics show that children are safer if they are restrained in the rear than the front seat. It is recommended that child restraints be secured in a rear seat, including an infant riding in a rear- facing infant seat, a child riding in a forward-facing child seat and an older child riding in a booster seat.

NOTE: The "PASSENGER AIR BAG OFF" indicator illuminates for about 6 seconds after the ignition key is turned to the "ON" position or after the engine is started. If the front passenger seat is occupied, the occupant classification sensor will then classify the front passenger within approximately 10
seconds after the ignition is turned on.

CAUTION:

If the occupant classification system is not working properly, the SRS airbag warning light on the instrument panel will illuminate because the passenger's front airbags are connected with the occupant classification system. If there is a malfunc- tion of the occupant classification system, the "PASSENGER AIR BAG OFF" indicator will not illuminate and the passenger's front airbags will inflate in frontal impact crashes even if there is no occupant in the front passenger's seat. If the SRS airbag warning light does not illuminate when the ignition key is turned to the "ON" position, remains illuminated after approximately 6 seconds when the ignition key is turned to the "ON" position, or if it illuminates while the vehicle is being driven, have an authorized Hyundai dealer inspect the occupant classification system and the SRS airbag system as soon as possible.

WARNING:

o Even though your vehicle is equipped with the occupant classification sys- tem, do not install a child restraint sys- tem in the front passenger's seat. A child restraint system must never be placed in the front seat. Children who are too large for child restraint systems should al- ways occupy the rear seat and use the available lap/shoulder belts. Children are afforded the most safety in the event of an accident when they are restrained by a proper restraint system in the rear seat. o If the "PASSENGER AIR BAG OFF" indi- cator is illuminated when the front passenger's seat is occupied by an adult and he/she sits properly (sitting upright with the seat back in an upright position, centered on the seat cushion with their seat belt on, legs comfortably extended and their feet on the floor), have that person sit in the rear seat.

o If you change the weight on the front passenger seat, the "PASSENGER AIR BAG OFF" indicator may be turned on or off for a few seconds, disabling or en- abling the passenger airbags.

1FEATURES OF YOUR HYUNDAI 42

WARNING:

o A smaller-stature adult who is not seated correctly (for example: seat excessively reclined, leaning on the center console, hips shifted forward in the seat, or feet placed on the dashboard) can cause a condition where the advanced frontal air bag system senses less weight than if the occupant were seated properly (sit- ting upright with the seat back in an upright position, centered on the seat cushion with their seat belt on, legs comfortably extended and their feet on the floor). This condition can result in an adult potentially being misclassified and illumination of the "PASSENGER AIR BAG OFF" indicator.

B990B04Y-AAT Side Impact Airbag

B990B02Y Your Hyundai is equipped with a side impact airbag in each front seat. The purpose of the airbag is to provide the vehicle's driver and/or the front passenger with additional protection than that offered by the seat belt alone. The side impact airbags are designed to deploy only during certain side impact collisions, depending on the crash severity, angle, speed and point of impact. The side impact airbags are not de- signed to deploy in all side impact situations.

Side airbag sensor

B990B01O

WARNING:

o The side impact airbag is supplemental to the driver's and the passenger's seat belt systems and is not a substitute for them. Therefore your seat belts must be worn at all times while the vehicle is in motion. The side airbags deploy only in certain side impact conditions severe enough to cause significant injury to the vehicle occupants.

!

WARNING:

o For the best protection from the side impact airbag system and to avoid being injured by the deploying side impact airbag, both front seat occupants should sit in an upright position with the seat belt properly fastened. The driver's hands should be placed on the steering wheel at the 9:00 and 3:00 o'clock posi- tions. The passenger's arms and hands should be placed on their laps.

o Do not use any accessory seat covers. o Use of seat covers could reduce or pre-

vent the effectiveness of the system.

o Do not install any accessories on the

side or near the side impact airbag.

o Do not use excessive force on the side of

the seat.

o Do not place any objects over the airbag

or between the airbag and yourself.

o Do not place any objects (an umbrella, bag, etc.) between the front door and the front seat. Such objects may become dangerous projectiles and cause injury if the supplemental side impact airbag inflates.

WARNING:

o To prevent unexpected deployment of the side impact air bag that may result in personal injury, avoid impact to the side impact airbag sensor when the ignition key is on.

B240C02O-AAT SRS Care

o The SRS is virtually maintenance free and there are no parts you can safely service by yourself. If the SRS SRI (Service Reminder Indicator) does not illuminate, or continu- ously remains on, have your vehicle imme- diately inspected by your Hyundai dealer

o Any work on the SRS system, such as removing, installing, repairing, or any work on the steering wheel or front seats must be performed by a qualified Hyundai technician. Improper handling of the airbag system may result in serious personal injury.

FEATURES OF YOUR HYUNDAI

43

B240C01HP

WARNING:

o Do not install a child restraint system in

the front passenger seat position. A child restraint system must never be placed in the front seat. The infant or infant or child could be severely injured by an airbag deployment in case of an accident.

o Modification to SRS components or wir- ing, including the addition of any kind of badges to the pad covers or modifica- tions to the body structure, can ad- versely affect SRS performance and lead to possible injury.

1FEATURES OF YOUR HYUNDAI 44

WARNING:

o For cleaning the airbag pad covers, use only a soft, dry cloth or one which has been moistened with plain water. Sol- vents or cleaners could adversely affect the airbag covers and proper deploy- ment of the system.

o No objects should be placed over or near the airbag modules on the steering wheel, instrument panel, and the front passenger's panel above the glove box, because any such object could cause harm if the vehicle is in a crash severe enough to cause the airbags to inflate. o If the airbags inflate, they must be re- placed by an authorized Hyundai dealer. o Do not tamper with or disconnect SRS wiring, or other components of the SRS system. Doing so could result in injury due to accidental deployment of the airbags or by rendering the SRS inopera- tive.

WARNING:

o If components of the airbag system must be discarded, or if the vehicle must be scrapped, certain safety precautions must be observed. Your Hyundai dealer knows these precautions and can give you the necessary information. Failure to follow these precautions and proce- dures could increase the risk of personal injury.

o If you sell your vehicle, make certain that this manual is transferred to the new owner.

o If your vehicle has been flooded and has soaked carpeting or water on the floor, you shouldn't try to start the engine; have the car towed to an authorized Hyundai dealer.

o Do not replace the bumper or the bumper guard with the one other than the Hyundai genuine parts. Otherwise, it can ad- versely affect SRS performance and lead to unexpected injury.

B240D01O-AAT Additional Safety Precautions o Never let passengers ride in the cargo area or on top of a folded-down back seat. All occupants should sit upright, fully back in their seats with their seat belts on and their feet on the floor.

o Passengers should not move out of or change seats while the vehicle is mov- ing. A passenger who is not wearing a seat belt during a crash or emergency stop can be thrown against the inside of the vehicle, against other occupants, or out of the ve- hicle.

o Each seat belt is designed to restrain one occupant. If more than one person uses the same seat belt, they could be seriously injured or killed in a collision.

o Do not use any accessories on seat belts. Devices claiming to improve occu- pant comfort or reposition the seat belt can reduce the protection provided by the seat belt and increase the chance of serious injury in a crash.

o Passengers should not place hard or sharp objects between themselves and the airbags. Carrying hard or sharp objects on your lap or in your mouth can result in injuries if an airbag inflates.

FEATURES OF YOUR HYUNDAI

45

o Keep occupants away from the airbag covers. All occupants should sit upright, fully back in their seats with their seat belts on and their feet on the floor. If occupants are too close to the airbag covers, they could be injured if the airbags inflate.

o Do not attach or place objects on or near the airbag covers. Any object attached to or placed on the front or side impact airbag covers could interfere with the proper opera- tion of the airbags.

o Do not modify the front seats. Modifica- tion of the front seats could interfere with the operation of the supplemental restraint sys- tem sensing components or side impact airbags.

o Do not place items under the front seats. Placing items under the front seats could interfere with the operation of the supple- mental restraint system sensing compo- nents and wiring harnesses.

o Never hold an infant or child on your lap. The infant or child could be seriously injured or killed in the event of a crash. All infants and children should be properly restrained in appropriate child safety seats or seat belts in the rear seat.

WARNING:

o Sitting improperly or out of position can result in serious injury or death in a crash.

o Always sit upright with the seat back in an upright position, centered on the seat cushion with your seat belt on, legs comfortably extended and your feet on the floor.

Adding Equipment to or Modifying Your Airbag-Equipped Vehicle.

If you modify your vehicle by changing your vehicle's frame, bumper system, front end or side sheet metal or ride height, this may affect the operation of your vehicle's airbag system.

1FEATURES OF YOUR HYUNDAI 46

INSTRUMENT CLUSTER AND INDICATOR LIGHTS

B260A01O-AAT

B260A01O-A

FEATURES OF YOUR HYUNDAI

47

1. 4WD System Warning Light (If installed) 2. ABS Service Reminder Indicator (If installed) 3. Tachometer 4. Turn Signal Indicator Lights 5. Coolant Temperature Gauge 6. Automatic Transaxle Position Indicator Light 7. Low Fuel Warning Light 8. Fuel Gauge 9. Speedometer 10.Malfunction Indicator Light (MIL) 11.Tail Gate Open Warning Light 12.Traction Control Indicator Light (If installed) 13.Traction Control OFF Indicator Light (If installed)

14.Charging System Warning Light 15.Door Ajar Warning Light 16.Parking Brake/Low Brake Fluid Level Warning Light 17.Seat Belt Warning Light 18.Low Oil Pressure Warning Light 19.Odometer / Trip Odometer / Trip Computer (If installed) 20.High Beam Indicator Light 21.Front Fog Indicator Light (If installed) 22.Supplemental Restraint System (Airbag)

Service Reminder Indicator (SRI) 23.Cruise Indicator Light (If installed) 24.Cruise SET Indicator Light (If installed)

1FEATURES OF YOUR HYUNDAI 48

WARNING AND INDICATOR LIGHTS

B260B01JM-AAT

B260E02O-AAT

B260G01A-AAT

SRS (Airbag) Service Reminder Indicator (SRI)

Seat Belt Reminder Light and Chime

The SRS service reminder indicator (SRI) comes on for about 6 seconds after the ignition key is turned to the "ON" position or after the engine is started, after which it will go out.

The seat belt reminder light blinks until your seat belt is fastened when the ignition key is turned from the "OFF" position to "ON" or "START" and the warning chime will sound for 6 seconds.

This light also comes on when the SRS is not working properly. If the SRI does not come on, or continuously remains on after coming on for about 6 seconds when you turned the ignition key to the "ON" position or started the engine, or if it comes on while driving, have the SRS inspected by an authorized Hyundai Dealer.

B260F01A-AAT

High Beam Indicator Light

The high beam indicator light comes on when- ever the headlights are switched to the high beam or flash position.

B260D01A-AAT

Turn Signal Indicator Lights

B260F01A-AAT

The blinking green arrows on the instrument panel show the direction indicated by the turn signals. If the arrow comes on but does not blink, blinks more rapidly than normal, or does not illuminate at all, a malfunction in the turn signal system is indicated. Your dealer should be consulted for repairs.

Front Fog Indicator Light (If installed)

This front fog indicator light comes on whenever the front fog lamp switches are on.

Low Oil Pressure Warning Light

CAUTION:

If the low oil pressure warning light stays on while the engine is running, serious engine damage may result. The oil pressure warn- ing light comes on whenever there is insuf- ficient oil pressure. In normal operation, it should come on when the ignition switch is turned on, then go out when the engine is started. If the oil pressure warning light stays on while the engine is running, there is a serious malfunction. If this happens, stop the car as soon as it is safe to do so, turn off the engine and check the oil level. If the oil level is low, fill the engine oil to the proper level and start the engine again. If the light stays on with the engine running, turn the engine off imme- diately. In any instance where the oil light stays on when the engine is running, the engine should be checked by a Hyundai dealer before the car is driven again.

FEATURES OF YOUR HYUNDAI

49

The brake fluid level warning light indicates that the brake fluid level in the brake master cylinder is low and hydraulic brake fluid conforming to DOT 3 or DOT 4 specifications should be added. After adding fluid, if no other trouble is found, the car should be immediately and care- fully driven to a Hyundai dealer for inspection. If further trouble is experienced, the vehicle should not be driven at all but taken to a dealer by a professional towing service or some other safe method. Your Hyundai is equipped with dual-diagonal braking systems. This means you still have braking on two wheels even if one of the dual systems should fail. With only one of the dual systems working, more than normal pedal travel and greater pedal pressure are required to stop the car. Also, the car will not stop in as short a distance with only half of the brake system working. If the brakes fail while you are driving, shift to a lower gear for additional engine braking and stop the car as soon as it is safe to do so.

B260J02A-AAT

Charging System Warning Light

The charging system warning light should come on when the ignition is turned on, then go out when the engine is running. If the light stays on while the engine is running, there is a malfunc- tion in the electrical charging system. If the light comes on while you are driving, stop, turn off the engine and check under the hood. First, make certain the generator drive belt is in place. If it is, check the tension of the belt. Do this as shown on page 6-19 by pushing down on the center of the belt. Have the system checked by your Hyundai dealer as soon as possible.

B260B01O-AAT

Tail Gate Open Warning Light

This light remains on unless the tail gate or tail gate window is completely closed and latched.

B260H02A-AAT

Parking Brake/Low Brake Fluid Level Warning Light

WARNING:

If you suspect brake trouble, have your brakes checked by a Hyundai dealer as soon as possible. Driving your car with a problem in either the brake electrical sys- tem or brake hydraulic system is danger- ous, and could result in a serious injury or death.

Warning Light Operation The parking brake/brake fluid level warning light should come on when the parking brake is applied and the ignition switch is turned to "ON" or "START". After the engine is started, the light should go out when the parking brake is re- leased. If the parking brake is not applied, the warning light should come on when the ignition switch is turned to "ON" or "START", then go out when the engine starts. If the light comes on at any other time, you should slow the vehicle and bring it to a complete stop in a safe location off the roadway.

1FEATURES OF YOUR HYUNDAI 50

B260L02HP-GAT

B260N02A-AAT

Door Ajar Warning Light and Chime (If Installed)

The door ajar warning light warns you that a door is not completely closed and the chime warns you that the key is in the ignition switch. NOTE : The warning chime only sounds whenever the key is in the ignition switch and the driver's side front door is open simulta- neously. The chime sounds until the key is removed from the ignition switch or the driver's side front door is closed.

B260M01A-AAT

Low Fuel Level Warning Light

The low fuel level warning light comes on when the fuel tank is approaching empty. When it comes on, you should add fuel as soon as possible. Driving with the fuel level warning light on or with the fuel level below "E" can cause the engine to misfire and damage the catalytic converter.

Malfunction Indicator Light

This light illuminates when there is a malfunction of an exhaust gas related component, and the system is not functioning properly so that the exhaust gas regulation values are not satisfied. This light will also illuminate when the ignition key is turned to the "ON" position, and then it will go out in a few seconds after the engine is started. If it illuminates while driving, or does not illuminate when the ignition key is turned to the "ON" position, take your car to your nearest authorized Hyundai dealer and have the system checked.

B260P02Y-GAT

ABS Service Reminder Indicator (If installed)

When the key is turned to the "ON" position, the Anti-Lock Brake System indicator will come on and then go off in a few seconds. If the ABS SRI remains on, comes on while driving, or does not come on when the key is turned to the "ON" position, this indicates that there may be a problem with the ABS. If this occurs, have your vehicle checked by your Hyundai dealer as soon as possible. The normal braking system will still be operational, but without the assistance of the anti-lock brake system.

WARNING:

If both the ABS SRI and Parking Brake/ Brake fluid level warning lights remain "ON" or come on while driving, there may be a problem with E.B.D. (Electronic Brake Force Distribution). If this occurs, avoid sudden stops and have your vehicle checked by your Hyundai dealer as soon as possible.

B260C01O-GAT

Traction Control Indicator Light (If installed)

The traction control indicator changes opera- tion according to the ignition switch position and whether or not the system is in operation. It will also illuminate when the ignition key is turned to the "ON" position, but should go out after three seconds. If the TCS indicator stays on, take your car to your authorized Hyundai dealer and have the system checked. See section 2 for more information about the TCS.

B265C01O-AAT

B260R01O-AAT

Traction Control Indicator Lights (3.5 L only) (If installed)

Cruise SET Indicator Light (If installed)

The traction control indicators change opera- tion according to the ignition switch position and whether the system is in operation or not. They will illuminate when the ignition key is turned to the "ON" position, but should go out after three seconds. If the TCS or TCS-OFF indicator stays on, take your car to your autho- rized Hyundai dealer and have the system checked. See section 2 for more information about the TCS.

B260Q03O-DAT

Cruise Indicator Light (If installed)

The cruise indicator light in the instrument clus- ter is illuminated when the cruise control ON/ OFF switch is pushed on the steering wheel. The indicator light does not illuminate when the cruise control ON/OFF switch is pushed again. Information about the use of cruise control is beginning on page 1-89.

The cruise set indicator light in the instrument cluster is illuminated when the cruise control "SET (COAST)" switch is pushed on the steer- ing wheel. The indicator light does not illuminate when the cruise control "SET (COAST)" switch is pushed again or the cruise control "CANCEL" switch is pushed.

B260T01O-GAT

4WD System Warning Light (If installed)

When the key is turned to the "ON" position, the 4WD(Four Wheel Drive) system warning light will come on and then go off in a few seconds.

CAUTION:

If the 4WD system warning light ( ) blinks while driving, this indicates that there is a malfunction in the 4WD system. If this oc- curs, have your vehicle checked by an au- thorized Hyundai dealer as soon as pos- sible.

FEATURES OF YOUR HYUNDAI

51

B270A01O-AAT BRAKE PAD WEAR WARNING SOUND

The front and rear disc brake pads have wear indicators that should make a high-pitched squealing or scraping noise when new pads are needed. The sound may come and go or be heard all the time when the vehicle is moving. It may also be heard when the brake pedal is pushed down firmly. Excessive rotor damage will result if the worn pads are not replaced. See your Hyundai dealer immediately.

B270B01O-AAT PARKING START WARNING SOUND

If the vehicle driven at over 2mph(3km/h) more 2~3 seconds, the warning chime will sound continuously when the parking brake engaged.

B900A01A-AAT LIGHTS ON WARNING SOUND

The warning chime sounds when the tail lights are on and the driver side door is open. This prevents the battery from discharging by warn- ing you when the car is left with the tail lights on. The chime sounds until the tail lights are turned off.

1FEATURES OF YOUR HYUNDAI 52

INSTRUMENT CLUSTER

B280A01A-AAT FUEL GAUGE

B290A03A-AAT ENGINE COOLANT TEMPERATURE GAUGE

The normal range is approximately in the middle between "H" and "C". If it moves across the dial to "H" (HOT), pull over and stop as soon as possible and turn off the engine. Then open the hood and, after the engine has cooled, check the coolant level and the water pump drive belt. If you suspect cooling system trouble, have your cool- ing system checked by a Hyundai dealer as soon as possible.

B280A01O The needle on the gauge indicates the approxi- mate fuel level in the fuel tank. The fuel capacity is given in Section 9.

B290A01O

WARNING:

Never remove the radiator cap when the engine is hot. The engine coolant is under pressure and could erupt and cause severe burns. Wait until the engine is cool before adding coolant to the reservoir.

B330A02A-AAT TACHOMETER

B300A01A-AAT SPEEDOMETER

B310B01O-AAT ODOMETER/TRIP ODOMETER (Without Trip Computer)

FEATURES OF YOUR HYUNDAI

53

B330A01O The tachometer registers the speed of your engine in revolutions per minute (rpm).

B300A01O-A Your Hyundai's speedometer is calibrated in miles per hour (on the outer scale) and kilome- ters per hour (on the inner scale).

CAUTION:

The engine should not be raced to such a speed that the needle enters the red zone on the tachometer face. This can cause severe engine damage and may void your warranty.

HSM2079
Pushing in the trip switch for less than 1 second when the ignition switch is turned "ON" displays the following sequence:

1FEATURES OF YOUR HYUNDAI 54

NOTE: Federal law forbids alteration of the odom- eter of any vehicle with the intent to change the number of the odometer. The alteration may void your warranty coverage.

2, 3. Trip Odometer

Trip odometer records the distance of 2 trips in kilometers or miles.

TRIP A: First distance you have traveled from your origination point to a first destination.

TRIP B: Second distance from the first destina- tion to the final destination.

B310C01O-AAT ODOMETER/TRIP ODOMETER (With Trip Computer)

Trip Odometer

When the trip switch is pressed for more than 1 second, trip odometer will reset to 0.

1. Odometer

B310B01O-E

1. Odometer

The odometer records the total driving distance in miles, and is useful for keeping a record for maintenance intervals. It is normal for a new vehicle to have the odometer indicating less than 30 miles.

The odometer records the total driving distance in kilometers or miles, and is useful for keeping a record for maintenance intervals. It is normal for a new vehicle to have the odometer indicating less than 30 miles.

NOTE: Federal law forbids alteration of the odom- eter of any vehicle with the intent to change the number of the odometer. The alteration may void your warranty coverage.

Odometer

B400B04O-E

2. Trip Odometer

o This mode indicates the drive distance trav-

elled since the last drive time reset.

o Refer to the explanation of the trip computer

(see page 1-57, Tripmeter).

TRIP COMPUTER

B400B01O-GAT (If installed)

FEATURES OF YOUR HYUNDAI

55

Trip Computer Switch

o The trip computer switch is used to zero the

multi-functional display mode.

o Pushing in the trip computer switch changes

the display as follows;

DISTANCE TO EMPTY

AVERAGE FUEL CONSUMPTION

AVERAGE SPEED

TRIPMETER

HSM2079
The trip computer is a microcomputer-con- trolled driver information gauge that displays information related to driving, such as a dis- tance to empty, average fuel consumption, average speed and tripmeter on the LCD.

1FEATURES OF YOUR HYUNDAI 56

1. Distance to Empty

Distance to empty symbol

Distance to empty

NOTE: o If the distance to empty is less than 30
miles (50km),the symbol "RANGE" will blink and the distance to empty "----" digits come on until more fuel is added. o The distance to empty can differ from the actual tripmeter according to driving conditions.

o The distance to empty can vary accord- ing to the driving conditions, driving pattern or vehicle speed.

2. Average Fuel Consumption

Average fuel consumption symbol

Average fuel consumption

Odometer

B400B01O-A

Odometer

B400B02O-A

o This mode provides the estimated distance to empty from the current fuel level in the fuel tank.

o The trip computer may not register additional fuel if less than 6.34 U.S. quarts (6 liters) of fuel are added to the vehicle.

o When the battery has been reinstalled after being discharged or disconnected, drive more than 40 miles (64km) for an accurate distance to empty.

o This mode calculates the average fuel con- sumption from the total fuel used and the distance since the last average consump- tion reset.

o The total fuel used is calculated from the fuel

consumption input.

o For an accurate calculation, drive more than

0.03 mile (0.05 km) or 10 seconds.

o Average fuel consumption is reset to zero if

the battery is disconnected.

o To reset the average fuel consumption to zero, press the trip computer switch for more than 1 second.

3. Average Speed

Average speed symbol

4. Tripmeter

Average speed

Tripmeter

Odometer

Odometer

B400B03O-A

B400B04O-E

o This mode indicates the average speed from the starting of the vehicle to the ignition key "OFF". When the ignition key is "OFF", it will initialize to 0 mph(0 km/h).

o Average speed is reset to zero if the battery

is disconnected.

o To reset the average speed to zero, press the trip computer switch for more than 1
second.

o This mode indicates the total distance trav- elled since the last tripmeter reset. Total distance is also reset to zero if the battery is disconnected.

o Pressing the trip computer switch for more than 1 second, when the tripmeter is being displayed, clears the tripmeter to zero.

FEATURES OF YOUR HYUNDAI

MULTI-FUNCTION LIGHT SWITCH

57

B340A01A-AAT COMBINATION TURN SIGNAL, HEADLIGHT AND HIGH-BEAM SWITCH Turn Signal Operation

Pulling down on the lever causes the turn signals on the left side of the car to blink. Pushing upwards on the lever causes the turn signals on the right side of the car to blink. As the turn is completed, the lever will automatically return to the center position and turn off the turn signals at the same time. If either turn signal indicator light blinks more rapidly than usual, goes on but does not blink, or does not go on at all, there is a malfunction in the system. Check for a burned- out fuse or bulb or see your Hyundai dealer.

1FEATURES OF YOUR HYUNDAI 58

B340B01A-AAT Lane Change Signal

B340C03A-AAT Headlight Switch

B340D01A-AAT High-beam Switch

B340B01O To indicate a lane change, move the lever up or down to a point where it begins flashing. The lever will automatically return to the center position when released.

B340D01O To turn on the headlight high beams, push the lever forward (away from you). The High Beam Indicator Light will come on at the same time. For low beams, pull the lever back toward you.

B340C01O To operate the headlights, turn the barrel on the end of the multi-function switch. The first posi- tion turns on the parking lights, sidelights, tail lights and instrument panel lights. The second position turns on the headlights. NOTE: The ignition must be in the "ON" position to turn on the headlights.

Parking Light Auto Off

If you do not turn the parking lights "OFF" after driving, the parking lights will automatically shut "OFF" when the driver's door is opened. To turn them "ON" again, you must simply turn the ignition key to the "ON" position.

B340E01A-AAT Headlight Flasher

B340G01LZ-GAT Auto Light (If installed)

B340E01O To flash the headlights, pull the switch lever toward you, then release it. The headlights can be flashed even though the headlight switch is in the "OFF" position.

HSM2094
To operate the automatic light feature, turn the barrel on the end of the multi-function switch. If you set the multi-function switch to "AUTO", the tail lights and headlights will be turned automati- cally on or off according to external illumination.

NOTE: Switch on car light manually in foggy, cloudy and rainy conditions.

FEATURES OF YOUR HYUNDAI

59

Auto light sensor

HSM2095

NOTE: o Never place anything over sensor lo- cated on the instrument panel, this will ensure better auto light system control. o Don't clean the sensor using a window

cleaner.

o If your vehicle has window tint or other types of coating on the front windshield, the AUTO light system may not work properly.

1FEATURES OF YOUR HYUNDAI 60

WINDSHIELD WIPER AND WASHER SWITCH

B350A01A-AAT

(1)

(2)

(3)

B350A01O-A The windshield wiper switch has three posi- tions:

Intermittent wiper operation

1. 2. Low-speed operation 3. High-speed operation

NOTE: To prevent damage to the wiper system, do not attempt to wipe away heavy accumula- tions of snow or ice. Accumulated snow and ice should be removed manually. If there is only a light layer of snow or ice, operate the heater in the defrost mode to melt the snow or ice before using the wiper.

B350B01O-GAT Windshield Washer Operation

Mist Wiper Operation

B350B01O-A To use the windshield washer, pull the wiper/ washer lever toward the steering wheel. When the washer lever is operated, the wipers auto- matically make two passes across the wind- shield. The washer continues to operate until the lever is released.

B350B02O-A If a single wipe is desired in mist, push the windshield wiper and washer control lever up- wards.

NOTE: o Do not operate the washer more than 15
seconds at a time or when the fluid reservoir is empty.

o In icy or freezing weather, be sure the wiper blades are not frozen to the glass prior to operating the wipers.

o In areas where water freezes in winter,

use windshield washer antifreeze.

B350C01O-AAT Adjustable Intermittent Wiper Operation

B390A01JM-AAT Rear Window Wiper And Washer (If installed)

FEATURES OF YOUR HYUNDAI

61

NOTE: Do not operate the washer continuously for more than 15 seconds or when the fluid reservoir is empty; this could damage the system. Do not operate the wiper when the window is dry; this can result in scratching as well as premature wiper blade wear.

B350C01O-A To use the intermittent wiper feature, place the wiper switch in the "INT" position. With the switch in this position, the interval between wipes can be varied from approximately 1 to 18
seconds by turning the interval adjuster barrel. It also can be varied by vehicle speeds within same time.

1.

2.OFF 3.INT:

B350D01O-A : The rear window wiper starts to oper- ate three times after the washer fluid sprays onto the rear window.

The interval between wipes operates every 5 seconds intermittently.

4.ON : The rear window wiper starts to oper-

5.

ate continuously.

: The washer fluid will be sprayed onto the rear window and the wiper oper- ates while the rear window wiper bar- rel is placed in this position.

1FEATURES OF YOUR HYUNDAI 62

FRONT FOG LIGHT SWITCH

HAZARD WARNING SYSTEM

B360A04A-AAT (If installed)

B370A01A-AAT

REAR WINDOW DEFROSTER SWITCH B380A01HP-AAT

B360A01O-A To turn on the front fog lights, push the switch. They will light when the headlight switch is in the second position and the ignition key is in the "ON" position.

NOTE: If you turn on the headlight high beams, the front fog lights will be turned off.

B370A01O-A The hazard warning system should be used whenever you find it necessary to stop the car in a hazardous location. When you must make such an emergency stop, always pull off the road as far as possible. The hazard warning lights are turned on by pushing in the hazard switch. This causes all turn signal lights to blink. The hazard warning lights will operate even though the key is not in the ignition. To turn the hazard warning lights off, push the switch a second time.

B380A01O-A The rear window defroster switch also acti- vates the outside rear view mirror heaters. The rear window defroster and heated outside rearview mirrors are turned on by pushing in the switch. To turn the defroster off, push the switch a second time. The rear window defroster automatically turns itself off after about 20 min- utes. To restart the defroster cycle, push in the switch again after it has turned itself off.

DIGITAL CLOCK

B400A01A-AAT

FEATURES OF YOUR HYUNDAI

ELECTRIC AZIMUTH COMPASS

63

B990C01O-AAT (With sunroof) (If installed)

CAUTION:

Do not clean the inner side of the rear window glass with an abrasive type of glass cleaner or use a scraper to remove foreign deposits from the inner surface of the glass as this may cause damage to the defroster elements.

NOTE: The ignition must be in the "ON" position for the rear window defroster to operate.

B400A01O-A There are three control buttons for the digital clock. Their functions are:

HOUR - Push "H" to advance the hour indi- cated. MIN - Push "M" to advance the minute indicated. RESET - Push "R" to reset minutes to ":00" to facilitate resetting the clock to the correct time. When this is done:

Pressing "R" between 10 : 30 and 11 : 29
changes the readout to 11 : 00. Pressing "R" between 11 : 30 and 12 : 29
changes the readout to 12 : 00.

B990C01O It displays 8 azimuth according to the vehicle’s driving direction and the angle of one graduation is 45°. The indication is displayed only when the ve- hicle is in motion.

Heading Display E : East, W: West, S : South, N : North ex) NW : North West

NOTE: If new vehicle is first driven or if the battery has been disconnected, correct the azi- muth indicator before driving.

1FEATURES OF YOUR HYUNDAI 64

Correcting Azimuth Indicator

It is needed to correct the error between a current azimuth to terrestrial magnetism sen- sor and the displayed azimuth in the vehicle position.

How to correct azimuth indicator

1.

If you push and hold the "M (MODE)" switch for less than 4.5 seconds, the azimuth indi- cator will start blinking with the vehicle's present direction.

3. When the rotation is finished, the azimuth compass indicator will stop blinking and the error correction is completed. If the indicator continues to blink, rotate the vehicle a bit more until the blinking stops. The compass heading will appear after 3
seconds when the correcting error is com- pleted.

HSM2186

NOTE: Rotate the vehicle one turn (90 degree) as shown in the drawing if the vehicle has no place to rotate.

HSM2185

2. Slowly rotate the vehicle one turn(360 de-

gree) within 128 seconds. The rotation could be made at any direction(left or right) in an open space.

The azimuth compass indicator correc- tion will be cancelled:

1.

If you press "M (MODE)" switch for more than 0.5 second.

2. When the vehicle is not rotated within 128
seconds after the blinking of the indicator.

NOTE: The azimuth may display abnormally in specific places (tunnel, parking lot in build- ing, underground parking lot, near trans- former substation, etc.). It is normal and the azimuth is displayed normally when escap- ing above mentioned places.

How to correct terrestrial deviation.

1. Press "M (MODE)" switch for more than 4.5
seconds, then the present terrestrial devia- tion angle value will be displayed.

2. Press " (UP)" or " (DOWN)" switch for less than 0.5 second to correct the terrestrial deviation angle within 30 seconds.

FEATURES OF YOUR HYUNDAI

INSTRUMENT PANEL LIGHT CONTROL (RHEOSTAT)

65

The Counter Line Map for Terrestrial Deviation Angle Correction

B410A01A-AAT

For the correct terrestrial deviation angle value for your location, refer to the contour line map included. If your place is located in between the terres- trial deviation contour line, you can apply any value (up or down value) for your location in the contour line map. The initial deviation angle is set to 5°W. Terrestrial Correction Range: West 30° ~ East 30°.

3. To finish the correction, press "M (MODE)"

switch for more than 1 second.

NOTE: The terrestrial deviation setting will be re- membered even if the battery has been disconnected.

The terrestrial deviation angle correc- tion will be cancelled:

1.

2.

If you press "M (MODE)" switch for more than 0.5 second. If you don't correct the terrestrial deviation angle within 30 seconds.

B410A01O The instrument panel lights can be made brighter or dimmer by turning the instrument panel light control knob.

B990C02O-A

1FEATURES OF YOUR HYUNDAI 66

CIGARETTE LIGHTER

POWER OUTLETS

B420A01A-AAT

B500D010O-AAT

HSM2157
For the cigarette lighter to work, the key must be in the "ACC" position or the "ON" position. To use the cigarette lighter, push it all the way into its socket. When the element has heated, the lighter will pop out to the "ready" position. Do not hold the cigarette lighter pressed in. This can damage the heating element and create a fire hazard. If it is necessary to replace the cigarette lighter, use only a genuine Hyundai replacement or its approved equivalent.

HSM2158
The power outlets are located on the center facia panel and in the quarter trim. These supply 12V electric power to operate electric accessories or equipment only when the key is in the "ON" or "ACC" position.

CAUTION:

o Use when the engine is running and remove a plug from the power outlet after using the electric appliance. Using when the engine stops or remaining the electric appliance with plugged in for many hours may cause the battery to be discharged.

o Do not use the power outlet to connect electric accessories or equipment other than those designed to operate on 12
volts.

o Some electronic devices can cause elec- tronic interference when plugged into the power outlet. These devices may cause excessive audio noise and mal- functions in other electronic systems or devices used in your vehicle.

ASHTRAY

B430A01O-AAT Front Ashtray

B440A01O-AAT Rear Ashtray

FEATURES OF YOUR HYUNDAI

DRINK HOLDER

B450A01JM-AAT Front Drink Holder

67

HSM2164
The front ashtray may be opened by pulling it out by its grip. To clean ashtray, the plastic recep- tacle should be removed, by pressing the tab and pulling out. The ashtray light will only illumi- nate when the external lights are on.

HSM2165
The rear ashtray may be opened by pulling it out by its top edge.To clean ashtray, the plastic receptacle should be removed, by pressing the tab and pulling out.

B450A01O The front drink holder is located on the main console.

WARNING:

o Use caution when using the drink hold- ers. A spilled beverage that is very hot can injure you or your passengers. Spilled liquids can damage interior trim and electrical components.

o Do not place objects other than cups or cans in the drink holder. The objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the passengers in the vehicle.

1FEATURES OF YOUR HYUNDAI 68

B450B02O-AAT Rear Drink Holder

CAUTION:

Place the drink holder in its closed position when not in use.

B450B01JM-AAT Rear Drink Holder

WARNING:

Do not place objects other than cups or cans in the drink holder. The objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the passen- gers in the vehicle.

B450B01O The rear drink holder is located on the rear main console and may be used for holding cups. The rear drink holder can be used by pushing and pulling it at its top edge.

HSM2049
The rear drink holders is located in the rear seat arm rest. The rear drink holder can be used by pulling the rear seat armrest.

WARNING:

Do not place objects other than cups or cans in the drink holder. This objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the passen- gers in the vehicle.

SUNROOF

B460A01Y-AAT (If installed) Sun Shade

B460B01O-GAT Opening the Sunroof

FEATURES OF YOUR HYUNDAI

69

WARNING:

o Do not close a sunroof if anyone's hands, arms or body are between the sliding glass and the sunroof sash, as this could result in injury.

o Do not place your head or arms out of the

sunroof opening at any time.

B460A01O Your HYUNDAI is equipped with a sliding sun- shade which you can manually adjust to let in light with the sunroof closed, or to block sunlight.

WARNING:

Never adjust the sunshade while driving.

CAUTION:

o Do not open the sunroof in severely cold temperature or when it is covered with ice or snow.

o Periodically remove any dirt that may

have accumulated on the guide rails.

o Do not press any sunroof control button

longer than necessary. Damage to the motor or system compo- nents could occur.

HSM2022
The sunroof can be electrically opened or closed with the ignition key in the "ON" position. The sunroof is moved to its two-third open position by pushing the " "switch, and to stop at the desired position, push in any switches . To open the sunroof fully open position, push and re- lease the " " switch again in the first position (two-third open position). To close, press and hold the " " button. Release the button when the sunroof reaches the desired position.