2004 Hyundai Santa FE Owners Manual

The instrument panel lights can be made brighter or dimmer by turning the instrument panel light control knob.

B420A01O For the cigarette lighter to work, the key must be in the "ACC" position or the "ON" position. To use the cigarette lighter, push it all the way into its socket. When the element has heated, the lighter will pop out to the "ready" position. Do not hold the cigarette lighter pressed in. This can damage the heating element and create a fire hazard. If it is necessary to replace the cigarette lighter, use only a genuine Hyundai replacement or its approved equivalent.

B500D01O These are located in the quarter trim and on the center facia panel. These supply 12V electric power to operate electric accessories or equipment only when the key is in the "ON" or "ACC" position.

CAUTION:

Do not use the power outlet to connect electric accessories or equipment other than those designed to operate on 12 volts.

ASHTRAY

B430A01A-GAT Front Ashtray

B440A01E-AAT Rear Ashtray

FEATURES OF YOUR HYUNDAI

DRINK HOLDER

B450A02O-AAT Front Drink Holder

55

B430A01O The front ashtray may be opened by pulling it out by its grip. To remove the ashtray to empty or clean it, press down on the spring-loaded tab inside the ashtray and pull it all the way out. The ashtray light will only illuminate when the exter- nal lights are on.

B440A01O The rear ashtray may be opened by pulling it out by its top edge. To remove the ashtray to empty or clean it, press down on the spring-loaded tab inside the ashtray and lift the ashtray upward and pull it all the way out.

B450A01O The front drink holder is located on the main console and may be used for holding cups or cans.

WARNING:

o Use caution when using the drink hold- ers. A spilled beverage that is very hot can injure you or your passengers. Spilled liquids can damage interior trim and electrical components.

o Do not place objects other than cups or cans in the drink holder. The objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the passengers in the vehicle.

1FEATURES OF YOUR HYUNDAI 56

B450B02O-AAT Rear Drink Holder (If installed)

WARNING:

Do not place objects other than cups or cans in the drink holder. The objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the passen- gers in the vehicle.

SUNROOF

B460A01Y-AAT (If installed) Sun Shade

B450B01O The rear drink holder is located on the rear main console and may be used for holding cups. The rear drink holder can be used by pushing and pulling it at its top edge.

B460A01O Your HYUNDAI is equipped with a sliding sun- shade which you can manually adjust to let in light with the sunroof closed, or to block sunlight.

CAUTION:

Place the drink holder in its closed position when not in use.

WARNING:

Never adjust the sunshade while driving.

B460B01GK-GAT Opening the Sunroof System

WARNING:

o Do not close a sunroof if anyone's hands, arms or body are between the sliding glass and the sunroof sash, as this could result in injury.

o Do not place your head or arms out of the

sunroof opening at any time.

CAUTION:

o Do not open the sunroof in severely cold temperature or when it is covered with ice or snow.

o Periodically remove any dirt that may

have accumulated on the guide rails.

B460B01O The sunroof can be electrically opened or closed with the ignition key in the "ON" position. The sunroof is moved to its fully open position by pushing the "OPEN" switch, and to stop at the desired position, push in any switches (OPEN, CLOSE, UP, DOWN). To close, press and hold the "CLOSE" button. Release the button when the sunroof reaches the desired position.

FEATURES OF YOUR HYUNDAI

57

B460C01S-AAT Tilting the Sunroof System

B460C01O The sunroof can be tilted by pushing the "UP" button with sunroof closed. Release the button when the sunroof reaches the desired position. To close the sunroof, press the "DOWN" but- ton.

NOTE: After washing the car or after there is rain, be sure to wipe off any water that is on the sunroof before operating it.

1FEATURES OF YOUR HYUNDAI 58

B460D01O-GAT Manual Operation of Sunroof

If the sunroof does not electrically operate:

1. Open the spectacle case.

B460D01O

B460D02O 2. Turn the hexagonal bolts counterclockwise to remove the overhead console with a socket wrench.

3.

B460D03O Insert the hexagonal head wrench provided with the vehicle into the socket. This wrench can be found in the vehicle's glove box.

4. Turn the wrench clockwise to open or coun-

terclockwise to close.

INTERIOR LIGHT

B480B01O-AAT Map Light

With Sunroof

Without Sunroof

B490A03Y-AAT Interior Light

FEATURES OF YOUR HYUNDAI

59

o ON In the "ON" position, the light stays on at all times.

CAUTION

Do not leave this button pressed for an extended period of time when the vehicle is not running.

HSM046
Push in the map light switch to turn the light on or off. This light produces a spot beam for convenient use as a map light at night or as a personal light for the driver and the passenger.

B490A01O The interior courtesy light has three buttons. The three buttons are:

o DOOR In the " DOOR " position, the interior courtesy light comes on when any door is opened regard- less of the ignition key position. The light goes out gradually 6 seconds after the door is closed.

o OFF In the "OFF" position, the light stays off at all times even though a door is open.

1FEATURES OF YOUR HYUNDAI SPECTACLE CASE 60

B491A02O-GAT (If Installed)

With Sunroof

Without Sunroof

GLOVE BOX

B500A01S-AAT

UNLOCK

LOCK

B500A01O

B500B01O-AAT Illuminated Glove Box

Opening the glove box will automatically turn on the light when the multi-function switch is turned to the first/second position.

HSM170
The spectacle case is located on the front overhead console. Push the end of the cover to open the spectacle case.

WARNING:

Do not keep objects such as sharp or un- suitable things inside the spectacle case. Such objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the passengers in the vehicle.

WARNING:

To avoid the possibility of injury in case of an accident or a sudden stop, the glove box door should be kept closed when the car is in motion.

o To open the glove box, pull on the glove box

release lever.

o The glove box door can be locked (and

unlocked) with the key.

OUTSIDE REARVIEW MIRROR

B510A01A-AAT Manual Type

CAUTION:

If the mirror control is jammed with ice, do not attempt to break it free using the control handle or by manipulating the face of the mirror. Use an approved spray de-icer (not radiator antifreeze) to release the frozen mechanism or move the vehicle to a warm place and allow the ice to melt.

B510A01O The outside rearview mirrors are equipped with a remote control for your convenience. It is operated by the control lever in the bottom front corner of the window. Before driving away, always check that your mirrors are positioned so you can see behind you, both to the left and right sides, as well as directly behind your vehicle. When using the mirror, always exercise caution when attempt- ing to judge the distance of vehicles behind or along side of you.

FEATURES OF YOUR HYUNDAI

61

B510B01Y-AAT Electric Type (If installed)

B510B01O-A The outside rearview mirrors can be adjusted to your preferred rear vision, both directly be- hind the vehicle, and to the rear of the left and right sides. The remote control outside rearview mirror switch controls the adjustments for both right and left outside mirrors.

1FEATURES OF YOUR HYUNDAI 62

To adjust the position of either mirror:

1. Move the selecting switch to the right or left to activate the adjustable mechanism for the corresponding door mirror.

2. Adjust mirror angle by depressing the appro-

priate perimeter switch as illustrated.

B510B02O

CAUTION:

o Do not operate the switch continuously

for an unnecessary length of time.

o Scraping ice from the mirror face could cause permanent damage. To remove any ice, use a sponge, soft cloth or approved de-icer.

WARNING:

Be careful when judging the size or dis- tance of any object seen in the passenger side rear view mirror. It is a convex mirror with a curved surface. Any objects seen in this mirror are closer than they appear.

B510D01Y-AAT OUTSIDE REARVIEW MIRROR HEATER (If installed)

HSM035
The outside rearview mirror heater is actuated in connection with the rear window defroster. To heat the outside rearview mirror glass, push in the switch for the rear window defroster. The rearview mirror glass will be heated for defrost- ing or defogging and will give you improved rear vision in inclement weather conditions. Push the switch again to turn the heater off. The outside rearview mirror heater automatically turns itself off after 15 minutes.

DAY/NIGHT INSIDE REARVIEW MIRROR

FEATURES OF YOUR HYUNDAI

63

B510C01A-AAT FOLDING THE OUTSIDE REARVIEW MIRRORS

B520A01A-AAT Manual Type

B520B01O-GAT Electric Type (If installed)

B510C01O To fold the outside rearview mirrors, push them toward the rear. The outside rearview mirrors can be folded rearward for parking in narrow areas.

B520A01O Your Hyundai is equipped with a day/night inside rearview mirror. The "night" position is selected by flipping the tab at the bottom of the mirror toward you. In the "night" position, the glare of headlights of cars behind you is reduced.

B520B01O The electric type day/night inside rearview mir- ror controls automatically the glare of headlights of the car behind you. Adjust the rearview mirror to the desired position.

WARNING:

Do not adjust or fold the outside rearview mirrors while the vehicle is moving. This could result in loss of control, and an acci- dent which could cause death, serious in- jury or property damage.

1FEATURES OF YOUR HYUNDAI HOMELINK MIRROR 64

B520C01L-GAT (If installed)

Indicator Light

Glare Detection

Homelink buttons

B520C01L Your new vehicle may be equipped with an automatic night vision mirror. During nighttime driving, this feature will automatically detect and reduce dangerous rearview mirror glare.

Your new mirror also comes with an integrated HomeLink Universal Transceiver, which allows you to program up to 3 buttons on the mirror to activate your garage door(s), estate gate, home lighting, etc. The mirror actually learns the codes from your various existing transmitters.

Automatic-Dimming Function

HOMELINK PROGRAMMING

CAUTION:

o Make sure people and/or objects are out of the way of any garage doors or gates you may be operating during the pro- gramming procedures.

o Keep original transmitters for potential future programming needs, or in case you sell the vehicle.

o In the event you do sell your vehicle, it's recommended you erase your pro- grammed HomeLink mirror buttons.

Automatic-dimming mirror function buttons

B520C01L

To assist you during nighttime driving, your mirror will automatically dim upon detecting glare from the vehicles behind you.

Press the button to turn the automatic- dimming function off. The mirror indicator light will turn off.

Press the button to turn the automatic- dimming function on. The mirror indicator light will illuminate.

NOTE: The mirror defaults to the "on" position each time the vehicle is started.

WARNING:

Do not use HomeLink with any garage door opener that lacks the safety stop and re- verse feature as required by federal safety standards (includes garage doors manu- factured before April 1, 1982), as these doors can increase the risk of serious injury or death. Call 1-800-355-3515 or visit www.homelink.com for more information.

NOTE: If programming a garage door opener or gate, it is advised to unplug the device during the "cycling" process to prevent possible motor burnout.

Programming

Ensure the ignition switch is turned to the "ACC" position to program and/or operate HomeLink system. It is also recommended that a new battery be placed in the handheld transmitter of the device being programmed to HomeLink for quicker programming and accurate transmis- sion of the radio-frequency. Follow these steps to program your HomeLink mirror:

Flashing

1. When programming the buttons for the first time, press and hold the two outside HomeLink buttons ( , ), releasing when the indicator light begins to flash (approxi- mately 20 seconds). This procedure erases the factory-set default codes. Do not per- form this step when programming additional transmitters.

Flashing

1 ~ 3 inches

Transmitter

B520C03L 2. Hold the transmitter of the device you want to program 1 to 3 inches away from the bottom of the mirror. Simultaneously press the handheld transmitter button and the HomeLink button you wish to program. The indicator light will flash slowly at first, then rapidly, indicating successful programming.

B520C02L

FEATURES OF YOUR HYUNDAI

65

3.

If the garage door opener or other device you wish to program is rolling-code equipped, proceed to the "Rolling Code Programming" section.

4. Repeat step 2 to program the remaining

HomeLink buttons.

Additional Programming for Rolling Code Devices

For any rolling-code-equipped device; follow the steps additional below after completing the "Programming" section. A second person may make the following steps easier.

1. Locate the "learn" or "smart" button on the device's motor head unit. The exact location and color of the button varies by product brand, but is usually referenced in the device's owner's manual. Contact HomeLink at 1- 800-355-3515 or www.homelink.com for help.

2. Press and release the "learn" or "smart"

button on the device's motor head unit.

NOTE: You now have 30 seconds to initiate step 3.

1FEATURES OF YOUR HYUNDAI 66

3. Return to the vehicle and firmly press and release the programmed HomeLink button. Press and release the same HomeLink but- ton a second time to complete the program- ming process. (Some devices may require you to press and release a third time to complete the programming.)

4. Now HomeLink mirror and rolling-code- equipped device should be synchronized. The remaining HomeLink buttons may now be programmed if this has not been done previously.

Operating HomeLink

Simply press the appropriate HomeLink button to activate the trained product (garage door, security system, entry door lock, estate gate, lighting, etc.). The original handheld transmit- ters may also be used at any time.

Erasing Programmed Buttons

Flashing

Reprogramming a Single HomeLink Button

To program a device to HomeLink using a HomeLink button previously trained, follow these steps:

1. Press and hold the desired HomeLink but- ton. Do not release until step 4 has been completed.

2. When the indicator light begins to flash slowly (after 20 seconds), hold the handheld trans- mitter 1 to 3 inches away from the bottom of the mirror.

3. Press and hold the transmitter button (or, if necessary, press and "cycle," as described in the '"Gate Operator & Canadian Program- ming" portion of this text).

4. The HomeLink indicator light will flash slowly at first, then rapidly, indicating successful programming. Release both buttons.

B520C02L

To erase the three HomeLink buttons, press and hold the two outside buttons until the indica- tor light begins to flash (after 20 seconds). Release both buttons.

Individual buttons cannot be erased, but can be reprogrammed.

Gate Operator Programming & Cana- dian Programming

During programming, your handheld transmit- ter may automatically stop transmitting. Continue to press and hold the HomeLink button while you press and repress ("cycle") your handheld transmitter every two seconds until the frequency signal has been learned. The indicator light will flash slowly at first and then rapidly upon successful programming.

Accessories

For more information on HomeLink and HomeLink-compatible products, or to purchase HomeLink accessories, call 1-800-355-3515
or visit www.homeink.com.

PARKING BRAKE

TAIL GATE

B530A01A-AAT

B540A01FC-AAT

FEATURES OF YOUR HYUNDAI

67

B530A01O Always engage the parking brake before leav- ing the car. This also turns on the parking brake indicator light when the key is in the "ON" or "START" position. Before driving away, be sure that the parking brake is fully released and the indicator light is off.

o To engage the parking brake, pull the lever

up as far as possible.

o To release the parking brake, pull up and press the thumb button. Then, while holding the button in, lower the brake lever.

B540A01O

WARNING:

The tail gate should always be kept com- pletely closed while the vehicle is in motion. If it is left open or ajar, poisonous exhaust gases may enter the car resulting in serious illness or death to the occupants. See addi- tional warnings concerning exhaust gases on page 2-2.

o The tail gate can be locked or unlocked with

a key.

1FEATURES OF YOUR HYUNDAI 68

o The tail gate is opened by pulling the outside

handle up, raising the tail gate manually.

o To close, lower the tail gate, then press down on it until it is closed. To be sure the tail gate is fully closed, always try to pull it up again without using the outside handle.

B540B02O-AAT Tail gate Window

B540B01O

o When you push the tail gate window release button to open the tail gate window, it will spring up slightly. Raise the tail gate window. The window will raise completly by itself after it has been raised halfway.

LUGGAGE COMPARTMENT

B540C01HP-GAT LUGGAGE COMPARTMENT LIGHT

o To close the tail gate window, lower the tail

gate window, and it will close by itself. To be sure the tail gate window is securely fastened, always try to pull it up again.

NOTE: The tail gate window lock is operated is in connection with the tail gate lock. To open the tail gate window make sure the tail gate is unlocked with a key or the central door locking switch.

B540C01O Luggage compartment light has a 3-position switch. The three positions are:

o In the "MIDDLE" position, the luggage com- partment light comes on when the tail gate is opened, then goes out when it is closed.

o In the "ON" position, the light stays on at all

o In the "OFF" position, the light stays off at all

times.

times.

B640A01S-AAT CARGO SECURITY SCREEN (If installed)

B650A01S-AAT Stowage Precautions

B540D02O-AAT LUGGAGE NET

FEATURES OF YOUR HYUNDAI

69

1. Do not place objects on the cargo security screen. Such objects may be thrown about inside the vehicle and possibly injure vehicle occupants during an accident or when brak- ing.

2. For better fuel economy, do not carry unnec-

essary weight.

3. Never allow anyone to ride in the luggage compartment. It is designed for luggage only.

4. Try to maintain the balance of the vehicle and locate the weight as far forward as possible.

HSM233
When loading the objects in the luggage com- partment, use the four rings located in the luggage compartment to attach the luggage net as shown illustration. This will help prevent the objects from sliding.

B640A01O To use the security screen, pull it out of the retractor and hook it to the anchors as illus- trated.

1FEATURES OF YOUR HYUNDAI 70

CAUTION:

To prevent damage to the goods or the vehicle, care should be taken when carrying fragile or bulky objects in the luggage com- partment.

WARNING:

Avoid eye injury. DO NOT overstretch. The luggage net ALWAYS keep your face and body out of its recoil path. DO NOT use when the strap has visible signs of wear or damage.

ROOF RACK

B630A02B-AAT (If installed)

CAUTION:

o In case the sunroof is equipped, do not position roof rack loads that could inter- fere with opening of the sunroof.

o The following specifications are recom- mended when loading cargo or luggage.

ROOF RACK

75 lbs (34 kg) Evenly Distributed

B630A01O If your Hyundai has a roof rack, you can load things on top of your vehicle. Crossrails and fixing components to adapt the roof rack on your vehicle may be obtained from an authorized Hyundai dealer.

o Loading cargo or luggage above 75 lbs (34 kg) on the roof rack may damage your vehicle. When you carry large objects, never let them hang over the rear or the sides of your vehicle.

o To prevent damage or loss of cargo as you are driving, check frequently to make sure the luggage carrier and cargo are still securely fastened.

o Always drive your vehicle at a moderate

speed.

o To use the roof rails as a roof rack, you must fit the roof rails with two or more crossrails or equivalent before carrying cargo or luggage on the roof.

o Loading cargo or luggage over specifi- cation on the roof rack may damage stability of your vehicle.

HIGH-MOUNTED REAR STOP LIGHT

AUTO FUEL CUT SWITCH

REMOTE FUEL-FILLER LID RELEASE

FEATURES OF YOUR HYUNDAI

71

B550A01A-AAT (If installed)

B560B01O-AAT

B560A02S-AAT

B550A01O In addition to the lower-mounted rear stoplights on either side of the car, the high mounted rear stoplight in the center of the rear window also lights when the brakes are applied.

B560B01O The auto fuel cut switch is located on the driver's side of the engine compartment. In the event of a collision or sudden impact, the auto fuel cut device cuts off the fuel supply. If this device is activated, it must be reset by pressing in on the top of the switch before the engine can be restarted.

WARNING:

Before resetting the auto fuel cut switch, the fuel line should be checked for fuel leaks.

B560A01O The fuel-filler lid may be opened from inside the vehicle by pulling up on the fuel-filler lid opener located on the front floor area on the left side of the car.

NOTE: If the fuel-filler lid will not open because ice has formed around it, tap lightly or push on the lid to break the ice and release the lid. Do not pry on the lid. If necessary, spray around the lid with an approved de-icer fluid (do not use radiator anti-freeze) or move the vehicle to a warm place and allow the ice to melt.

1FEATURES OF YOUR HYUNDAI 72

B560A02O-1

WARNING:

o The fuel cap must be tightened at least 3 clicks, otherwise " " light will illuminate.

o Gasoline vapors are dangerous. Before refueling, always stop the engine and never allow sparks or open flames near the filler area. If you need to replace the filler cap, use a genuine Hyundai re- placement part.

WARNING:

o If you open the fuel filler cap during high ambient temperatures, a slight "pres- sure sound" may be heard. This is nor- mal and not a cause for concern. Whenever you open the fuel filler cap, turn it slowly.

o Make sure the fuel filler cap is replaced and securely seated after fueling. Failure to replace or fully seat the fuel filler cap will result in fuel vapors escaping into the atmosphere and the check engine "MIL" indicator illuminating.

o Do not "TOP-OFF" after the first nozzle

shut off when refueling.

HOOD RELEASE

B570A01L-GAT

B570A01O 1. Pull the release knob to unlatch the hood.

B570A02O

FLOOR MAT ANCHOR

SUN VISOR

B571A03Y-AAT

B580A01L-AAT

FEATURES OF YOUR HYUNDAI

73

2. Push the secondary latch lever up and lift the

hood.

3. Raise the hood by hand.

When closing the hood, slowly close the hood and make sure it locks into place.

WARNING:

o Always double check to be sure that the hood is firmly latched before driving away. If it is not latched, the hood could open while the vehicle is being driven, causing a total loss of visibility, which might result in an accident.

o Do not move the vehicle with the hood in the raised position, as vision is ob- structed and the hood could fall or be damaged.

HXGS263

When using a floor mat on the front floor carpet, make sure it attaches to the floor mat anchor in your vehicle. This keeps the floor mat from sliding forward.

WARNING:

o Make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and interferes with the movement of the pedals during driving, It may cause an accident.

o Don't put an additional floor mat on the top of the fixed mat, otherwise the addi- tional mat may slide forward and inter- fere with the movement of the pedals.

Vanity mirror

B580A01O Your Hyundai is equipped with sun visors to give the driver and front passenger either frontal or sideward shade. To reduce glare or to shut out direct rays of the sun, turn the sun visor down. A vanity mirrors are provided on the back of the sun visor for the driver and front passenger.

NOTE: The Supplemental Restraint System (SRS) label containing useful information can be found on the back of each sun visor.

1FEATURES OF YOUR HYUNDAI 74

STEERING WHEEL TILT LEVER

B600A02Y-AAT

FRONT DOOR EDGE WARNING LIGHT B620A01S-AAT

WARNING:

Do not place the sun visor in such a manner that it obscures visibility of the roadway, traffic or other objects.

B580B01O-AAT Illuminated Vanity Mirror (If installed)

Opening the lid of the vanity mirror will automati- cally turn on the mirror light when the multi- function switch is turned to the first/second position.

To adjust the steering wheel:

B600A01O

B620A01O

A red light comes on when the front door is opened. The purpose of this light is to assist when you get in or out and also to warn passing vehicles.

1. Pull the lever upward and hold it to unlock. 2. Raise or lower the steering wheel to the

desired position.

3. After adjustment, release the lever.

WARNING:

Do not attempt to adjust the steering wheel while driving as this may result in loss of control of the vehicle and serious injury or death.

HORN

B610A01L-GAT

REAR SEAT ARM REST

CRUISE CONTROL

B611A01Y-AAT

B660A01S-AAT (If installed)

FEATURES OF YOUR HYUNDAI

75

B610A01O Press the pad on the steering wheel to sound the horn.

B611A01O-A This arm rest is located in the center of the rear seat back.

B660A01O The cruise control system provides automatic speed control for your comfort when driving on freeways, tollroads, or other noncongested highways. This system is designed to function above approximately 25 mph (40 km/h).

1FEATURES OF YOUR HYUNDAI 76

B660B03O-AAT To Set the Cruise Speed

B660B01O 1. Push the cruise control ON´OFF button. The "CRUISE" indicator light in the instru- ment cluster will illuminate. This turns the system on.

2. Accelerate to desired cruising speed above

25 mph (40 km/h).

3. Push the "SET" (COAST) button after you have set the vehicle speed at the desired speed.

4. Remove your foot from the accelerator pedal and the desired speed will automatically be maintained.

B660C02O-AAT To cancel the cruise speed

5. To increase speed, temporarily depress the accelerator pedal enough for the vehicle to exceed the preset speed. When you remove your foot from the accelerator pedal, the vehicle will return to the speed you have set.

NOTE: If the vehicle speed decreases more than 12
mph (20 km/h) below the set speed or decreases below 25 mph (40 km/h), the cruise control system will automatically cancel the set speed.

B660C01O To disengage the cruise control system, push the "CANCEL" button. Additionally, the following actions will disengage the system:

o Depress the brake pedal. o Depress the clutch pedal (Manual transaxle). o Shift the selector lever to "N" position

(Automatic transaxle).

o Decrease the vehicle speed lower than the

memory speed by 12 mph (20 km/h).

o Decrease the vehicle speed to less than 25

mph (40 km/h).

o Release the "MAIN" button.

B660D01O-AAT To Resume the Preset Speed

B660F02O-AAT To Reset at a Slower Speed

B660D01O The vehicle will automatically resume the speed set prior to cancellation when you push the "RESUME (ACCEL)" button, providing the ve- hicle speed is above 25 mph (40 km/h).

B660E01Y-AAT To Reset at a Faster Speed

B660B01O

1. Push the "SET (COAST)" button and hold it. While the control button is pushed, the ve- hicle speed will gradually decrease.

2. When the desired speed is obtained, release

the control button.

1. Push the "RESUME (ACCEL)" button and

hold it.

2. Accelerate to desired speed and release the "RESUME (ACCEL)" switch. While the con- trol switch is held, the vehicle will gradually gain speed.

FEATURES OF YOUR HYUNDAI

77

WARNING:

o Keep the main switch off when not using

the cruise control.

o Use the cruise control system only when traveling on open highways in good weather.

o Do not use the cruise control when it may not be safe to keep the car at a constant speed, for instance, driving in heavy or varying traffic, or on slippery (rainy, icy or snow-covered) or winding roads or over 6% up-hill or down-hill roads.

o Pay particular attention to the driving conditions whenever using the cruise control system.

o During cruise-control driving with a manual transaxle vehicle, do not shift into neutral without depressing the clutch pedal, or the engine will be overrevved. If this happens, depress the clutch pedal or release the main switch. o During normal cruise control operation, when the "SET" button is activated or reactivated after applying the brakes, the cruise control will energize after approximately 3 seconds. This delay is normal.

1FEATURES OF YOUR HYUNDAI 78

HEATING AND COOLING CONTROL

B710A01O-GAT (If installed)

1 2

B710B02O-AAT Center Ventilator

The center ventilators are located in the middle of the dashboard. To change the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side. The vents are opened when the vent knob is moved to " " position. The vents are closed when the vent knob is moved to " ". Keep these vents clear of any obstructions.

B710C02O-AAT Side Ventilator

The side ventilators are located on each side of the front door. To change the direction of the air flow, move the knob in the center of the vent up- and-down and side-to-side. The vents are opened when the vent knob is moved to " " position. The vents are closed when the vent knob is moved to " ". Keep these vents clear of any obstructions.

1. Side Ventilator 2. Side Defroster Nozzle 3. Windshield Defroster Nozzle 4. Center Ventilator

HSM417

HEATING AND VENTILATION

FEATURES OF YOUR HYUNDAI

79

B670A03O-AAT (If installed)

B670B01O-AAT Fan Speed Control (Blower Control)

B670C02O-AAT Air Intake Control Switch

B690A01O-1
There are three controls and two switches for the heating and cooling system. They are:

1. Air intake control switch 2. Air conditioning switch 3. Air flow control 4. Fan speed control 5. Temperature control

B670B01O-1
This is used to select the blower fan speed. The blower fan speed, and therefore the volume of air delivered from the system, may be con- trolled manually by setting the blower control between the "1" and "4" position.

B670C02O This is used to select fresh outside air or recirculating inside air.

Fresh Recirculation

With the " " mode selected, air enters the vehicle from outside and is heated or cooled according to the other functions selected. With the " " mode selected, air from within the passenger compartment is drawn through the heating system and heated or cooled ac- cording to the other functions selected.

1FEATURES OF YOUR HYUNDAI 80

NOTE: o It should be noted that prolonged opera- tion of the heating system in " " mode will give rise to fogging of the wind- shield and side windows and the air within the passenger compartment will become stale. In addition prolonged use of the air conditioning with the " " mode selected may result in the air within the passenger compartment becoming excessively dry.

o When the ignition switch is turned "ON" the air intake control switch will change to " " mode in floor, floor-defrost and defrost position. This is normal opera- tion. But, the air intake control switch will change to " " mode when the ignition switch is turned "ON" with the MAX A/C mode selected.

B670D03O-AAT Air Flow Control

B670D02O

Face-Level

Selecting the "Face" mode will cause air to be discharged through the face level vents.

B670D01O-1
This is used to turn the blower fan on/off and to direct the flow of air. Air can be directed to the floor, dashboard outlets, or windshield. Five symbols are used to represent Face, Bi-Level, Floor, Floor-Defrost and Defrost air position. The MAX A/C mode is used to cool the inside of the vehicle faster. The "OFF" mode is used to turn the blower fan off.

FEATURES OF YOUR HYUNDAI

81

B670D03O

HSM118

HSM119

Bi-Level

Floor-Level

Floor-Defrost Level

Air is discharged through the face vents and the floor vents. This makes it possible to have cooler air from the dashboard vents and warmer air from the floor outlets at the same time.

Air is discharged through the floor vents, wind- shield defroster nozzle, side defroster nozzle and side ventilator. If the "Floor" mode is selected, the "Fresh" mode will be activated.

Air is discharged through the windshield de- froster nozzle, the floor vents, side defroster nozzle and side ventilator. If the "Floor-Defrost" mode is selected, the A/C will turn on automatically and "Fresh" mode will be activated.

1FEATURES OF YOUR HYUNDAI 82

mode except the defrost mode and the floor-defrost mode. Although the A/C switch indicator is turned off, this is normal operation.

NOTE: o The air intake control switch will change to " " mode when the ignition switch is turned "ON" with the MAX A/C mode selected.

o When you change to another mode from MAX A/C, the A/C and the air intake control switch are set to the following chart.

A/C

ON

ON or OFF *

Air Intake

Control Switch

or *

HSM428

OFF

OFF

MAX A/C

MAX A/C-Level

Air is discharged through the face level vents. If the "MAX A/C" mode is selected, the A/C will turn on automatically and "Recirculation" mode will be activated.

ON or OFF *

ON

ON

* The A/C or the air intake control switch

returns to its former setting.

HSM120

Defrost-Level

Air is discharged through the windshield de- froster nozzle, side defroster nozzle and side ventilator. If the "Defrost" mode is selected, the A/C will turn on automatically and "Fresh" mode will be ac- tivated to improve windshield defrosting.

NOTE: If the "Floor-Defrost" or "Defrost" mode is selected, the air conditioning will not turn off by pushing the A/C button. If the air flow control is set to the defrost or the floor-defrost mode, the A/C will be on automatically and the A/C will not off until the air flow control is set to the another

FEATURES OF YOUR HYUNDAI

HEATING CONTROLS

83

B670E02A-AAT Temperature Control

B690A01O-AAT

B670D07O

OFF Off-Level Air is discharged through the windshield de- froster nozzle, side defroster nozzle and side ventilator.

NOTE: If the air flow control is off, the air intake control is set to the fresh mode automati- cally.

Cool

Warm

B670E01O This control is used to adjust the degree of heating or cooling desired.

B690A01O-1
For normal heating operation, set the air flow control to the floor ( ) position. (The "Fresh" mode will be activated.)

For faster heating, the air intake control switch should be set in the recirculate ( ) position.

If the windows fog up, set the air flow control to the defrost ( ) position (The A/C will turn on automatically and "Fresh" mode will be acti- vated.)

For maximum heat, move the temperature con- trol to "Warm".

1FEATURES OF YOUR HYUNDAI BI-LEVEL HEATING 84

VENTILATION

AIR CONDITIONING SYSTEM

B700A01O-AAT

B710A01O-AAT

B740A01S-AAT (If installed) Air Conditioning Switch

B700A01O-1
Your Hyundai is equipped with bi-level heating controls. This makes it possible to have cooler air from the dashboard vents and warmer air from the floor outlets at the same time. To use this feature:

o Set the air intake control switch to the fresh

air ( ) position.

o Set the air flow control at the bi-level ( )

speed.

o Set the temperature control between "Cool"

and "Warm".

position.

and "Warm".

To operate the ventilation system:

B710A01O-1

o Set the air intake control switch to the fresh

air ( ) position.

o To direct all intake air to the dashboard vents, set the airflow control to the face ( ) position.

o Adjust the fan speed control to the desired

o Set the temperature control between "Cool"

B740A01O The air conditioning is turned on or off by pushing the A/C button on the heating/air con- ditioning control panel.

B740B03O-AAT Air Conditioning Operation Cooling

o Set the temperature control to "Cool". ("Cool" provides maximum cooling. The tempera- ture may be moderated by moving the con- trol toward "Warm".)

o Adjust the fan control to the desired speed. For greater cooling, turn the fan control to one of the higher speeds or temporarily select the recirculate ( ) position on the air intake control switch.

B740B01O-1
To use the air conditioning to cool the interior:

o Set the air flow control to the face ( ) position. o Turn on the air conditioning switch by push- ing in on the switch. The air conditioning indicator light should come on at the same time.

o Set the air intake control switch to the fresh

air ( ) position.

FEATURES OF YOUR HYUNDAI

85

B740C02O-AAT De-Humidified Heating

For dehumidified heating:

B740C01O-1

o Set the air flow control to the face ( ) position. o Turn on the air conditioning switch. The air conditioning indicator light should come on at the same time.

o Set the air intake control switch to the fresh

air ( ) position.

o Adjust the fan control to the desired speed. o For more rapid action, set the fan at one of

the higher speeds.

o Adjust the temperature control to provide the

desired amount of warmth.

1FEATURES OF YOUR HYUNDAI 86

B730A01L-AAT Operation Tips

o To keep dust or unpleasant fumes from entering the car through the ventilation sys- tem, temporarily set the air intake control switch to the position. Be sure to return the control switch to the position when the irritation has passed to keep fresh air in the vehicle. This will help keep the driver alert and comfort- able.

o Air for the heating/cooling system is drawn in through the grilles just ahead of the wind- shield. Care should be taken that these are not blocked by leaves, snow, ice or other obstructions.

o To prevent interior fog on the windshield, set the air intake control switch to the fresh air ( ) position, fan speed to the desired position, turn on the air conditioning system, and adjust temperature control to desired temperature.

B720A02E-AAT DEFROSTING/DEFOGGING Manual A/C

Full automatic A/C

Manual A/C

Full automatic A/C

FEATURES OF YOUR HYUNDAI

87

B720A02O-1

B720B02O-1

Use the heating/ventilation system to defrost or defog the windshield:

To remove interior fog on the windshield; o Set the air flow control to the defrost ( ) position. (The A/C will turn on automatically and the "Fresh" mode will be activated.)

o Set the temperature control to the desired position. o Set the fan speed control between "1" and "4" position.

To remove frost or exterior fog on the windshield; o Set the air flow control to the defrost ( ) position. (The A/C will turn on automatically and the "Fresh" mode will be activated.)

o Set the temperature control to warm. o Set the fan speed control to position "3" or "4".

NOTE: When the A/C is operated continuously on the floor-defrost level ( ) or defrost level ( ), it may cause fog to form on the exterior windshield. If this occurs, set the air flow control to the face level position ( ) and fan speed control to the low position.

1FEATURES OF YOUR HYUNDAI 88

AUTOMATIC HEATING AND COOLING CONTROL SYSTEM

B970A01Y-AAT (If installed)

B970B01O-AAT Heating and Cooling Controls

Your Hyundai is equipped with an automatic heating and cooling control system controlled by simply setting the desired temperature.

10

B970B01O

1. Temperature Control Button 2. AUTO (Automatic Control) Switch 3. Display Window 4. Air Flow Control Switch 5. Blower Fan Speed Control Switch

6. OFF Switch 7. Air Conditioning Switch 8. Air Intake Control Switch 9. Defroster Switch 10. Ambient Temperature Switch

B970C01O-GAT Automatic Operation

B970C01O The FATC (Full Automatic Temperature Con- trol) system automatically controls the heating and cooling by doing as follows:

1. Push the "AUTO" switch. The indicator light will come on confirming that the Face, Floor and/or Bi-Level modes as well as the blower speed and, the air conditioning will operate if ambient temperature is higher than 32°F (0°C) and automatically turns off if the ambi- ent temperature drops below 32°F(0°C).

B970C03O

2. Push the "TEMP" button to set the desired

temperature. The temperature will increase to the maxi- mum "HI" by pushing on the button. Each push of the button will cause the temperature to increase by 1°F(0.5°C). The temperature will decrease to the mini- mum "LO" by pushing on the button. Each push of the button will cause the temperature to decrease by 1°F(0.5°C).

FEATURES OF YOUR HYUNDAI

89

NOTE: If the battery has been discharged or dis- connected, the temperature mode will reset to Fahrenheit degree. This is a normal condition and you can adjust the temperature mode from Fahren- heit to Centigrade as follows; Press the TEMP down ( ) button 3 seconds or more with the AMB button held down. The display shows that the unit of tempera- ture is adjusted to Fahrenheit or Centigrade (°F →→→→→ °C or °C →→→→→ °F).

Photo sensor

HSM502

NOTE: Never place things on the sensor which is located in the car on the instrument panel to ensure better control of the heating and cooling system.

1FEATURES OF YOUR HYUNDAI 90

B995A01O-GAT AMBIENT TEMPERATURE SWITCH

B980B01Y-AAT Fan Speed Control

B670C02S-AAT Air Intake Control Switch

B995A01O Pressing the "AMB" button displays the ambient temperature on display window.

B980A01Y-AAT MANUAL OPERATION

The heating and cooling system can be con- trolled manually as well as by pushing buttons other than the "AUTO" button. At this state, the system sequentially works according to the order of buttons selected. The function of the buttons which are not se- lected will be controlled automatically. Press the "AUTO" button in order to convert to automatic control of the system.

B980B01O The fan speed can be set to the desired speed by pressing the appropriate fan speed control button. The higher the fan speed is, the more air is delivered. Pressing the "OFF" button turns off the fan.

B670C01O This is used to select fresh outside air or recirculation inside air. To change the air intake control mode, (Fresh mode, Recirculation mode) push the control button.

FRESH MODE ( ) : The indicator light on the button goes off when the air intake control is in fresh mode.

RECIRCULATION MODE ( ) : The indicator light on the button is illuminated when the air intake control is in recirculation mode.

B980D01Y-AAT Heating and Cooling System Off

B980E01O-AAT Air Flow Control

FEATURES OF YOUR HYUNDAI

91

B980D01O Press the "OFF" button to stop the operation of the heating and cooling system.

HSM218

This is used to direct the flow of air. Air can be directed to the floor, dashboard outlets, or windshield. Four symbols are used to represent Face, Bi-Level, Floor and Floor-Defrost posi- tion.

With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooled according to the function selected.

With the "Recirculation" mode selected, air from within the passenger compartment will be drawn through the heating system and heated or cooled according to the function selected.

NOTE: o It should be noted that prolonged opera- tion of the heating system in "recircula- tion" mode will give rise to fogging of the windshield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the "Re- circulation" mode selected may result in the air within the passenger compart- ment becoming excessively dry.

o When the ignition switch is turned "ON" the air intake control will change to "FRESH" mode (regardless of the switch position). This is normal operation. The air intake control operates in "AUTO" mode when turning the ignition to the "ON" position if the "AUTO" mode was used before shutting off the engine.

1FEATURES OF YOUR HYUNDAI 92

B670D02O

B670D03O

HSM118

Face-Level

When selecting the "Face-Level", the indicator light will come on, causing air to be discharged through the face level vents.

Bi-Level

When selecting the "Bi-Level", the indicator light will come on and the air will be discharged through the face vents and the floor vents. This makes it possible to have cooler air from the dashboard vents and warmer air from the floor outlets at the same time.

Floor-Level

When selecting the "Floor-Level", the indicator light will come on and the air will be discharged through the floor vents, windshield defroster nozzle, side defroster nozzle and side ventila- tor.

B980F02O-AAT Defrost Switch

B740D01Y-AAT Operation Tips

FEATURES OF YOUR HYUNDAI

93

o If the interior of the car is hot when you first get in, open the windows for a few minutes to expel the hot air.

o When you are using the air conditioning system, keep all windows closed to keep hot air out.

o When moving slowly, as in heavy traffic, shift to a lower gear. This increases engine speed, which in turn increases the speed of the air conditioning compressor.

o On steep grades, turn the air conditioning off to avoid the possibility of the engine over- heating.

o During winter months or in periods when the air conditioning is not used regularly, run the air conditioning once every month for a few minutes. This will help circulate the lubri- cants and keep your system in peak oper- ating condition.

HSM119

Floor-Defrost Level

When selecting the "Floor-Defrost Level", the indicator light will come on and the air will be discharged through the windshield defroster nozzle, the floor vents, side defroster nozzle and side ventilator.

B980F01O When the "Defrost" button is pressed, the "Fresh" mode will be automatically selected and the air will be discharged through the windshield de- froster nozzle, side defroster nozzle and side ventilator. To assist in defrosting, the air conditioning will operate if ambient temperature is higher than 32°F(0°C) and automatically turns off if the ambient temperature drops below 32°F(0°C).

1FEATURES OF YOUR HYUNDAI 94

STEREO SOUND SYSTEM

B750A02A-AAT How Car Audio Works FM reception

Ionosphere

AM reception

Ionosphere

FM radio station

Mountains

Unobstructed area

Buildings

B750A02L AM broadcasts can be received at greater distances than FM broadcasts. This is because AM radio waves are transmitted at low frequen- cies. These long, low frequency radio waves can follow the curvature of the earth rather than travelling straight out into the atmosphere. In addition, they curve around obstructions so that they can provide better signal coverage.

B750A01L AM and FM radio signals are broadcast from transmitter towers located around your city. They are intercepted by the radio antenna on your car. This signal is then received by the radio and sent to your car speakers. When a strong radio signal has reached your vehicle, the precise engineering of your audio system ensures the best possible quality repro- duction. However, in some cases the signal coming to your vehicle may not be strong and clear. This can be due to factors such as the distance from the radio station, closeness of other strong radio stations or the presence of buildings, bridges or other large obstructions in the area.

Iron bridges

Obstructed area

B750A03L FM broadcasts are transmitted at high frequen- cies and do not bend to follow the earth's surface. Because of this, FM broadcasts gen- erally begin to fade at short distances from the station. Also, FM signals are easily affected by buildings, mountains, or other obstructions. These can result in certain listening conditions which might lead you to believe a problem exists with your radio. The following conditions are normal and do not indicate radio trouble:

FEATURES OF YOUR HYUNDAI

95

B750B03Y-AAT Using a cellular phone or a two-way radio

When a cellular phone is used inside the vehicle, noise may be produced from the audio equip- ment. This does not mean that something is wrong with the audio equipment. In such a case, use the cellular phone at a place as far as possible from the audio equipment.

WARNING:

Don't use a cellular phone when you are driving. Stop at a safe place to use a cellular phone.

B750A04L o Fading - As your car moves away from the radio station, the signal will weaken and sound will begin to fade. When this occurs, we suggest that you select another stronger station.

o Flutter/Static - Weak FM signals or large obstructions between the transmitter and your radio can disturb the signal causing static or fluttering noises to occur. Reducing the treble level may lessen this effect until the disturbance clears.

B750A05L o Station Swapping - As an FM signal weak- ens, another more powerful signal near the same frequency may begin to play. This is because your radio is designed to lock onto the clearest signal. If this occurs, select another station with a stronger signal.

o Multi-Path Cancellation - Radio signals being received from several directions can cause distortion or fluttering. This can be caused by a direct and reflected signal from the same station, or by signals from two stations with close frequencies. If this occurs, select another station until the condition has passed.

1FEATURES OF YOUR HYUNDAI 96

AUDIO SYSTEM

H260A01O-AAT STEREO RADIO OPERATION (H260) (If installed)

3. BASS/TREBLE Control Knob

4. SCAN Button

6. BAND Selector

7. PRESET Button

5. TUNE/SEEK Select Button

1. POWER ON-OFF/VOLUME/BALANCE Control Knob

2. FADER Control Knob

H260A01O

FEATURES OF YOUR HYUNDAI

97

SEEK Operation (Automatic Channel Selection)

Press the TUNE select button for 0.5 sec or more. Releasing it will automatically tune to the next available station with a beep sound. When the ( ) side is pressed longer than 0.5
second, releasing will automatically tune to the next higher frequency and when the ( ) side is pressed longer than 0.5 second, releasing will automatically tune to the next lower frequency.

6. BAND Selector

FM/AM

Pressing the button changes the AM, FM1
and FM2 bands. The mode selected is dis- played on LCD.

7. PRESET STATION SELECT Button

Six (6) stations for AM, FM1 or FM2 respec- tively can be preset in the electronic memory circuit on this unit.

H260B04O-AAT 1. POWER ON-OFF Control Knob

The radio unit may be operated when the ignition key is in the "ACC" or "ON" position. Press the knob to switch the power on. The LCD shows the radio frequency in the radio mode or the CD track indicator in the CD mode. To switch the power off, press the knob again.

3. BASS Control Knob

Press to pop the knob out and turn to the left or right for the desired bass tone.

TREB (Treble Control) Knob

Pull the bass control knob further out. Turn to the left or right for the desired treble tone.

VOLUME Control

4. SCAN Button

When the scan button is pressed, the frequency will increase and the receivable stations will be tuned in one after another, receiving each sta- tion for 5 seconds. To stop scanning, press the scan button again.

5. TUNE (Manual) Select Button

Press the ( ) side or ( ) side to increase or to decrease the frequency. Press either button and hold down to continuously scroll. Release button once the desired station is reached.

Rotate the knob clockwise to increase the volume and turn the knob counterclockwise to reduce the volume.

BALANCE Control

Pull and turn the control knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counterclockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).

2. FAD (Fader Control) Knob

Turn the control knob counterclockwise to emphasize front speaker sound (rear speaker sound will be attenuated). When the control knob is turned clockwise, rear speaker sound will be emphasized (front speaker sound will be attenuated).

!

CAUTION:

o Do not place beverages close to the audio system. The audio system mecha- nism may be damaged if you spill them. o Do not impact on the audio system, or the audio system mechanism could be damaged.

1FEATURES OF YOUR HYUNDAI 98

HOW TO PRESET STATIONS

Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, by simply pressing the band select button and/or one of the six station select buttons, you may recall any of these stations instantly. To pro- gram the stations, follow these steps:

o Press band selector to set the band for AM,

FM1 or FM2.

o Select the desired station to be stored by

seek, scan or manual tuning.

o Determine the preset station select button

you wish to use to access that station.

o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which select button you have depressed. The frequency display will flash after it has been stored into the memory. You should then release the button, and proceed to program the next desired station. A total of 18 stations can be programmed by selecting one AM and two FM stations per button.

o When completed, any preset station may be recalled by selecting AM, FM1 or FM2 band and the appropriate station button.

FEATURES OF YOUR HYUNDAI

99

H260B01O-AAT COMPACT DISC PLAYER OPERATION (H260) (If installed)

4. SCAN Button

1. Playing CD

3. TRACK UP/DOWN

6. EJECT Button

2. FF/REW Button

5. REPEAT Button

H260A01O

1FEATURES OF YOUR HYUNDAI 100

B260D04O-AAT 1. Playing CD

o Insert the CD with the label facing upward. o Insert the CD to start CD playback, during

radio operation.

o When a disc is in the CD deck, if you press the CD button, the CD player will begin playing even if the radio is being used.

o The CD player can be used when the ignition switch is in either the "ON" or "ACC" position.

2. FF/REW ( / )

If you want to fast forward or reverse through the compact disc track, push and hold the FF ( ) or REW ( ) button. When you release the button, the compact disc player will resume playing.

3. TRACK UP/DOWN

o The desired track on the disc currently being played can be selected using the track number.

o Press once to skip forward to the beg-