2007 Honda S2000 Owners Manual

system helps to stabilize the vehicle during cornering if the vehicle turns more or less than desired. It also assists you in maintaining traction while accelerating on loose or slippery road surfaces. It does this by regulating the engine’s output and by selectively applying the brakes.

When VSA activates, you may notice that the engine does not respond to the accelerator in the same way it does at other times.

The VSA system cannot enhance the vehicle’s driving stability in all situations and does not control your vehicle’s entire braking system. It is still your responsibility to drive and corner at reasonable speeds and to leave a sufficient margin of safety.

130

Main MenuTable of ContentsstVehicle Stability Assist (VSA) System, Towing a Trailer

Immediately after freeing your vehicle, be sure to switch the VSA on again. We do not recommend driving your vehicle with the VSA and traction control systems switched off.

This switch is at the left side of the right vent. Press it to turn VSA on and off.

When VSA is off, the VSA activation indicator comes on as a reminder.

VSA is turned on every time you start the engine, even if you turned it off the last time you drove the vehicle.

VSA Off Switch

VSA OFF SWITCH

In certain unusual conditions when your vehicle gets stuck in shallow mud or fresh snow, it may be easier to free it with the VSA temporarily switched off. When the VSA system is off, the traction control system is also off. You should only attempt to free your vehicle with the VSA off if you are not able to free it when the VSA is on.

VSA and Tire Sizes Driving with varying tire or wheel sizes may cause the VSA to malfunction. When replacing tires, make sure they are of the same size and type as your original tires (see page

165

).

Deactivate the VSA system if you need to drive with the compact spare tire installed (see page

174

).

If you install winter tires, make sure they are the same size as those that were originally supplied with your vehicle. Exercise the same caution during winter driving as you would if your vehicle was not equipped with VSA.

Towing a Trailer Your vehicle is not designed to tow a trailer; Attempting to do so can void your warranties.

131

Main MenuTable of ContentsstThis section explains why it is important to keep your vehicle well maintained and how to follow basic maintenance safety precautions.

This section also includes instructions on how to read the maintenance minder messages on the information display, a maintenance record, and instructions for simple maintenance tasks you may want to take care of yourself.

If you have the skills and tools to perform more complex maintenance tasks on your vehicle, you may want to purchase the service manual. See page for information on how to obtain a copy, or see your dealer.

215

Maintenance

Maintenance Safety Maintenance Minder Maintenance Record Fluid Locations Adding Engine Oil Changing the Oil and Filter Engine Coolant Windshield Washers Manual Transmission Fluid Differential Fluid Brake and Clutch Fluid Lights Cleaning the Seat Belts Floor Mats Dust and Pollen Filter Audio Antenna Wiper Blades Wheels Tires Checking the Battery Vehicle Storage

...................... .................... .................... .............................. ........................ ......... .............................. .................... ........ .......................... ................ ............................................. ................ ..................................... .................. .............................. ................................. ........................................... ............................................... ................... .............................

. 134
. 135
. 143
. 145
. 146
. 147
. 149
. 151
. 152
. 153
. 154
. 155
. 160
. 161
. 161
. 161
. 162
. 163
. 163
. 169
. 171

133

Main MenustMaintenance Safety

All service items not detailed in this section should be performed by a certified technician or other qualified mechanic.

Important Safety Precautions To eliminate potential hazards, read the instructions before you begin, and make sure you have the tools and skills required.

Make sure your vehicle is parked on level ground, the parking brake is set, and the engine is off.

To clean parts, use a commercially available degreaser or parts cleaner, not gasoline.

To reduce the possibility of fire or explosion, keep cigarettes, sparks, and flames away from the battery and all fuel-related parts.

Wear eye protection and protective clothing when working with the battery or compressed air.

134

Improperly maintaining this vehicle, or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed.

Always follow the inspection and maintenance recommendations and schedules in this owner’s manual.

Potential Vehicle Hazards Carbon Monoxide poison from engine exhaust. there is adequate ventilation whenever you operate the engine.

Be sure

Burns from hot parts. Let the engine and exhaust system cool down before touching any parts.

Injury from moving parts. not run the engine unless instructed to do so.

Do

Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.

Always follow the procedures and precautions in this owner’s manual.

Some of the most important safety precautions are given here. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.

Main MenuTable of ContentsstYour vehicle displays engine oil life and maintenance service items on the information display to show you when you should have your dealer do engine oil replacement and indicated maintenance service.

Based on the engine operating conditions and accumulated engine revolutions, the onboard computer in your vehicle calculates the remaining engine oil life and displays it as a percentage.

Maintenance Minder

Engine Oil Life Display

TRIP BUTTON

The remaining engine oil life is shownonthedisplayaccordingto this table:

Calculated Engine

Displayed

ENGINE OIL LIFE DISPLAY

To see the current engine oil life, turn the ignition switch to the ON (II) position, and push and release the TRIP button repeatedly until the engine oil life display appears (see page

51

).

Oil Life (%) 91 % 100 % 90 % 81 % 71 % 80 % 61 % 70 % 51 % 60 % 41 % 50 % 40 % 31 % 21 % 30 % 16 % 20 % 11 % 15 % 6 % 10 % 5 % 1 %

− − − − − − − − − − − − 0 %

Engine Oil Life (%)

100 % 90 % 80 % 70 % 60 % 50 % 40 % 30 % 20 % 15 % 10 % 5 % 0 %

CONTINUED

135

Main MenuTable of ContentsstThe maintenance item code or codes indicate the main and sub items required at the time of the oil change (see page

142

).

The 15 and 10 percent oil life indicator reminds you that the time is coming soon to take your vehicle in for the required maintenance.

Maintenance Minder

MAINTENANCE MINDER INDICATOR

ENGINE OIL LIFE INDICATOR

MAINTENANCE ITEM CODE(S)

If the remaining engine oil life is 15
to 6 percent, you will see the engine oil life indicator every time you turn the ignition switch to the ON (II) position. The maintenance minder indicator will also come on, and the maintenance item code(s) for other scheduled maintenance items needing service will be displayed next to the engine oil life indicator.

136

Main MenuTable of ContentsstMaintenance Minder

When the remaining engine oil life is 5 to 1 percent, you will see a ‘‘SERVICE OIL LIFE’’ message along with the same maintenance item code(s), every time you turn the ignition switch to the ON (II) position. The maintenance minder indicator ( ) also comes on and remains on in the instrument panel.

When the remaining engine oil life is 0 percent, the engine oil life indicator will blink. The display comes on every time you turn the ignition switch to the ON (II) position. The maintenance minder indicator on in the instrument panel. When you see this message, immediately have the indicated maintenance done by your dealer.

) also comes on and remains

If you do not perform the indicated maintenance, negative mileage is displayed and begins to blink after the vehicle has been driven 10 miles (10 km) or more.

Negative mileage means your vehicle has passed the maintenance required point. Immediately have the indicated maintenance done by your dealer.

CONTINUED

137

Main MenuTable of ContentsstMaintenance Minder

The maximum total mileage shown is ‘‘ 9999.’’

−

You can change the information display from the engine oil life display to the odometer, the trip meter, or the outside temperature every time you press and release the TRIP button.

When the engine oil life is 0 percent or negative mileage, the maintenance minder indicator change the information display.

)remainsonevenifyou

Immediately have the service done, and make sure to reset the display as described on the next page.

Maintenance Main Items and Sub Items

MAINTENANCE SUB ITEM (S)

ENGINE OIL LIFE INDICATOR

MAINTENANCE MAIN ITEM

All maintenance items displayed in the information display are in code. For an explanation of these maintenance codes, see page

142

138

Main MenuTable of ContentsstResetting the Engine Oil Life Indicator Your dealer will reset the display after completing the required maintenance service. You will see ‘‘OIL LIFE 100%’’ on the information display the next time you turn the ignition switch to the ON (II) position.

If maintenance service is done by someone other than your dealer, reset the maintenance minder as follows:

1.

Turn the ignition switch to the ON (II) position.

2.

Press the TRIP button until the engine oil life indicator is displayed.

Maintenance Minder

ENGINE OIL LIFE INDICATOR

ENGINE OIL LIFE INDICATOR

3.

Press the TRIP button for about 10 seconds. The engine oil life indicator and the maintenance item code(s) will blink.

4.

Press the TRIP button for about 5
seconds. The maintenance items code(s) will disappear, and the engine oil life will reset to ‘‘100.’’

139

Main MenuTable of ContentsstMaintenance Minder

Important Maintenance Precautions If you have the required service done but do not reset the display, or reset the display without doing the service, the system will not show the proper maintenance intervals. This can lead to serious mechanical problems because you will no longer have an accurate record of when maintenance is needed.

Your authorized Honda dealer knows your vehicle best and can provide competent, efficient service.

However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Make sure to have the service facility or person reset the display as previously described. Keep all receipts as proof of completion, and have the person who does the work fill out the maintenance record. Check your warranty booklet for more information.

We recommend using Honda parts and fluids whenever you have maintenance done. These are manufactured to the same high quality standards as the original components, so you can be confident of their performance and durability.

140

Main MenuTable of ContentsstU.S. Vehicles: Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are ‘‘certified’’ to EPA standards.

＃

According to state and federal regulations, failure to perform maintenance on the items marked with will not void your emissions warranties. However, all maintenance services should be performed in accordance with the intervals indicated by the information display.

Maintenance Minder

−

Lights Check the operation of the headlights, parking lights, taillights, high-mount brake light, and license plate lights monthly. See page

155

Owner’s Maintenance Checks Youshouldcheckthefollowing items at the specified intervals. If you are unsure of how to perform any check, turn to the appropriate page listed.

Engine oil level Check every time you fill the fuel tank. See page

113

−

Engine coolant level Check the radiator reserve tank every time youfillthefueltank.Seepage

114

−

Brakes and clutch Check the fluid level monthly. See page 154

−

−

Tires Check the tire pressure monthly. Examine the tread for wear and foreign objects. See page 164

CONTINUED

141

Main MenuTable of ContentsstSymbol

Maintenance Minder

Symbol

Maintenance Main Items

Replace engine oil ＊ Replace engine oil and oil filter Inspect front and rear brakes Check parking brake adjustment Inspect these items:

Tie rod ends, steering gear box, and boots Suspension components Driveshaft boots Brake hoses and lines (including ABS) All fluid levels and condition of fluids Exhaust system ＃ Fuel lines and connections ＃

＊

1 :

If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is reset, change the engine oil every year.

See information on maintenance and emissions warranty on page

141

Independent of the maintenance minder messages, replace the brake fluid every 3 years. Inspect idle speed every 160,000 miles (256,000 km). Adjust the valves during services A, B, 1, 2, or 3 if they are noisy.

＃

NOTE:

142

Maintenance Sub Items

Check tire inflation and condition Replace air cleaner element

If you drive in dusty conditions, replace every 15,000
miles (24,000 km).

Replace dust and pollen filter

If you drive primarily in urban areas that have high concentrations of soot in the air from industry and from diesel-powered vehicles, replace every 15,000
miles (24,000 km).

Inspect drive belt Replace transmission fluid Replace spark plugs Inspect valve clearance Replace engine coolant Replace rear differential fluid

Driving in mountainous areas results in higher level of mechanical (shear) stress to fluid. This requires differential fluid changes more frequently than recommended by the maintenance minder. If you regularly drive your vehicle under these conditions, have the differential fluid changed every 15,000 miles (24,000 km).

Main MenuTable of ContentsstYou or the servicing dealer can record all completed maintenance here. When maintenance is performed, record the mileage, circle the coded item(s) completed, and write in any other non-coded items (such as brake fluid replacement) below the codes. Keep the receipts for all work done on your vehicle. Maintenance can also be recorded in your Honda service history booklet.

Mileage

Maintenance Performed

Signature

Date

Mileage

Maintenance Performed

Signature

Date

Maintenance Record

mi km

mi km

mi km

mi km

mi km

mi km

mi km

A B 1

A B 1

A B 1

A B 1

A B 1

A B 1

A B 1

mi km

mi km

mi km

mi km

mi km

mi km

mi km

A B 1

A B 1

A B 1

A B 1

A B 1

A B 1

A B 1

CONTINUED 143

Main MenuTable of ContentsstMaintenance Record

Mileage

Maintenance Performed

Signature

Date

Mileage

Maintenance Performed

Signature

Date

mi km

mi km

mi km

mi km

mi km

mi km

mi km

A B 1

A B 1

A B 1

A B 1

A B 1

A B 1

A B 1

144

mi km

mi km

mi km

mi km

mi km

mi km

mi km

A B 1

A B 1

A B 1

A B 1

A B 1

A B 1

A B 1

Main MenuTable of ContentsstENGINE OIL FILL CAP

WASHER FLUID (Blue cap)

ENGINE OIL DIPSTICK (Black handle)

Fluid Locations

CLUTCH FLUID (Gray cap)

BRAKE FLUID (Gray cap)

ENGINE COOLANT RESERVOIR

RADIATOR CAP

145

Main MenuTable of ContentsstMake sure the API Certification Seal says ‘‘For Gasoline Engines.’’

API CERTIFICATION SEAL

Recommended Engine Oil Oil is major contributor to your engine’s performance and longevity. Always use a premium-grade detergent oil displaying the API certification seal. This seal indicates the oil is energy conserving, and that it meets the American Petroleum Institute’s latest requirements. It is highly recommended that you use Honda motor oil in your vehicle for as long as you own it.

Adding Engine Oil

Unscrew and remove the engine oil fill cap on the valve cover. Pour in the oil slowly and carefully so you do not spill any. Clean up any spills immediately. Spilled oil could damage components in the engine compartment. Reinstall the engine oil fill cap, and tighten it securely. Wait a few minutes, and recheck the oil level on the engine oil dipstick. Do not fill above the upper mark; you could damage the engine.

146

Main MenuTable of ContentsstAdding Engine Oil, Changing the Oil and Filter

The oil’s viscosity or weight is provided on the container’s label. Select the oil for your vehicle according to this chart.

Ambient Temperature

Synthetic Oil You may use a synthetic motor oil if it meets the same requirements given for a conventional motor oil: it displays the API Certification Seal, and it is the proper weight. You must follow the oil and filter change intervals shown on the information display.

Engine Oil Additives Your vehicle does not require any oil additives. Additives may adversely affect the engine or transmission performance and durability.

An oil with a viscosity of 10W-30 is preferred for optimum fuel economy and year-round protection in your vehicle. You may use 5W-40 oil if the temperature in your area goes below 0°F (

20°C).

−

Changing the Oil and Filter Always change the oil and filter according to the maintenance messages shown on the information display. The oil and filter collect contaminants that can damage your engine if they are not removed regularly.

Changing the oil and filter requires special tools and access from underneath the vehicle. The vehicle should be raised on a service station- type hydraulic lift for this service. Unless you have the knowledge and proper equipment, you should have this maintenance done by a skilled mechanic.

1.

Run the engine until it reaches normal operating temperature, then shut it off.

CONTINUED

147

Main MenuTable of ContentsstChanging the Oil and Filter

WASHER

OIL DRAIN BOLT

OIL FILTER

2.

Open the hood, and remove the engine oil fill cap. Remove the oil drain bolt and washer from the bottom of the engine. Drain the oil into an appropriate container.

3.

Remove the oil filter, and let the remaining oil drain. A special wrench (available from your dealer) is required.

Make sure the oil filter gasket is not stuck to the engine block. If it is, remove it before installing a new oil filter.

148

4.

Install a new oil filter according to the instructions that come with it.

5.

Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten the drain bolt to: 29 lbf·ft (39 N·m , 4.0 kgf·m)

6.

Refill the engine with the recommended oil.

Engine oil change capacity (including filter): 5.1 US qt (4.8 )

7.

Install the engine oil fill cap. Start the engine. The oil pressure indicator should go out within 5
seconds. If it does not, turn off the engine, and check your work.

Main MenuTable of ContentsstChanging the Oil and Filter, Engine Coolant

8.

9.

Let the engine run for several minutes, then check the drain bolt and oil filter for leaks.

Adding Engine Coolant

RESERVE TANK

Turn off the engine and let it sit for several minutes, then check the oil level on the dipstick. If necessary, add more oil.

Improper disposal of engine oil can be harmf ul to the environment. If you change your own oil, please dispose of the used oil properly. Put it in a sealed container and take it to a recycling center. Do not discard it in a trash bin or dump it on the ground.

MAX

MIN

If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks.

Always use Honda Long-Life Antifreeze/Coolant Type 2. This coolant is pre-mixed with 50 % antifreeze and 50 % water. Never add straight antifreeze or plain water.

If Honda antifreeze/coolant is not available, you may use another major-brand non-silicate coolant as a temporary replacement. Make sure it is a high-quality coolant recommended for aluminum engines. Continued use of any non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Have the cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible.

CONTINUED

149

Main MenuTable of ContentsstEngine Coolant

If the reserve tank is completely empty, you should also check the coolant level in the radiator.

Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

150

3.

The coolant level should be up to the base of the filler neck. Add coolant if it is low.

Pour the coolant slowly and carefully so you do not spill any. Clean up any spill immediately; it could damage components in the engine compartment.

4.

Put the radiator cap on, and tighten it fully.

5.

Pour coolant into the reserve tank. Fill it to halfway between the MAX and MIN marks. Put the cap back on the reserve tank.

Do not add any rust inhibitors or other additives to your vehicle’s cooling system. They may not be compatible with the coolant or engine components.

RADIATOR CAP

1.

When the radiator and engine are cool, relieve any pressure in the cooling system by turning the radiator cap counterclockwise, without pressing down.

2.

Remove the radiator cap by pushing down and turning counterclockwise.

Main MenuTable of ContentsstWindshield Washers

Check the fluid level in the windshield washer reservoir at least monthly during normal use.

RESERVOIR CAP

Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather.

When you refill the reservoir, clean the edges of the windshield wiper blades with windshield washer fluid on a clean cloth. This will help to condition them.

Do not use engine antif reeze or a vinegar/water solution in the windshield washer reservoir. Antif reeze can damage your vehicle’s paint, while a vinegar/water solution can damage the windshield washer pump. Use only commercially-available windshield washer f luid.

LEVEL GAUGE

Check the fluid level by looking at the level gauge attached to the cap.

151

Main MenuTable of ContentsstManual Transmission Fluid

FILLER BOLT

CORRECT LEVEL

Check the fluid level with the transmission at normal operating temperature and the vehicle sitting on level ground. Remove the transmission filler bolt, and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Honda Manual Transmission Fluid (MTF) until it starts to run out of the hole. Install the filler bolt, and tighten it securely.

152

Put a new washer on the filler bolt, then reinstall the filler bolt and tighten it securely.

If Honda MTF is not available, you may use an SAE 10W-30 or 10W-40
viscosity motor oil with the API Certification seal that says ‘‘FOR GASOLINE ENGINES’’ as a temporary replacement. However, motor oil does not contain the proper additives, and continued use can cause stiffer shifting. Replace as soon as it is convenient.

The transmission should be drained and refilled with new fluid according to the intervals shown on the information display.

If you are not sure how to check and add fluid, contact your dealer.

Main MenuTable of ContentsstUse an SAE 90 viscosity hypoid gear oil, API service classified GL5 or GL6 only.

Put a new washer on the filler bolt, then reinstall the filler bolt. Tighten it securely. Tightening torque: 33 lbf·ft (45 N·m , 4.6 kgf·m)

The differential should be drained and refilled with new fluid according to the intervals shown on the information display.

If you are not sure how to check and add fluid, contact your dealer.

FILLER BOLT

CORRECT LEVEL

Check the fluid level with the differential at normal operating temperature and the vehicle sitting on level ground. Remove the differential fluid filler bolt and washer, and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, slowly add fluid until it starts to run out of the hole.

Differential Fluid

153

Main MenuTable of ContentsstBrake and Clutch Fluid

Check the brake fluid level in the reservoirs monthly.

Replace the brake fluid according to the time recommendation in the maintenance schedule.

Always use Honda Heavy Duty Brake Fluid DOT 3. If it is not available, you should use only DOT 3
or DOT 4 fluid, from a sealed container, as a temporary replacement.

Using any non-Honda brake fluid can cause corrosion and decrease the life of the system. Have the brake system flushed and refilled with Honda Heavy Duty Brake Fluid DOT 3 as soon as possible.

Brake fluid marked DOT 5 is not compatible with your vehicle’s braking system and can cause extensive damage.

154

Brake Fluid

MAX

Clutch Fluid

MAX

MIN

The fluid level should be between the MIN and MAX marks on the side of the reservoir. If the level is at or below the MIN mark, your brake system needs attention. Have the brake system inspected for leaks or worn brake pads.

MIN

The fluid level should be between the MIN and MAX marks on the side of the reservoir. If it is not, add brake fluid to bring it up to that level. Use the same fluid specified for the brake system.

A low fluid level can indicate a leak in the clutch system. Have this system inspected as soon as possible.

Main MenuTable of ContentsstHeadlight Aiming The headlights were properly aimed when your vehicle was new. If you regularly carry heavy items in the trunk, readjustment may be required. Adjustment should be done by your dealer or other qualified mechanic.

Replacing a Headlight Bulb The low beam headlight bulbs are a type of high voltage discharge tube. High voltage can remain in the circuit even with the light switch off and the key removed. Because of this, you should not attempt to examine or change a low beam headlight bulb yourself. If a low beam headlight bulb fails, take the vehicle to your dealer to have it replaced.

Lights

Halogen bulbs are used for the high beam headlight bulbs. When replacing a high beam headlight bulb, handle it by its base, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.

Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.

CONTINUED

155

Main MenuTable of ContentsstLights

1.

Open the hood. If you need to change the high beam headlight bulb on the driver’s side, remove the coolant reserve tank from its holder by pulling it straight up.

2.

Remove the electrical connector from the bulb by squeezing the connector to unlock the tab, then slide the connector off the bulb.

3.

Remove the rubber weather seal by pulling on the tab.

4.

Unclip the end of the hold-down wire from its slot. Pivot it out of the way, and remove the bulb socket.

5.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

156

6.

Insert the socket back into the headlight assembly. Make sure the bulb is installed correctly by looking through the headlight lens. The pins on the base of the bulb should fit in the holes in the headlight assembly. Pivot the hold- down wire back in place, and clip the end into the slot.

7.

Install the rubber seal over the back of the headlight assembly.

8.

Push the electrical connector onto the new bulb. Turn on the headlights to test the new bulb.

9.

(Driver’s side) Reinstall the coolant reserve tank.

Main MenuTable of ContentsstLights

Replacing Front Turn Signal and Side Marker/Parking Light Bulbs 1.

If you are changing the bulb on the driver’s side, start the engine, turn the steering wheel all the way to the right, then turn off the engine. If you are changing the bulb on the passenger’s side, turn the steering wheel to the left.

2.

Use a flat-tipped screwdriver to remove the three holding clips from the inner fender.

3.

Pull the inner fender cover back.

4.

Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise.

5.

Pull the bulb straight out of its socket.

6.

Install the new bulb in the socket.

7.

Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place.

8.

Turn on the lights to make sure the new bulb is working.

9.

Put the inner fender cover in place. Install the three holding clips. Lock each clip in place by pushing on the center.

157

Main MenuTable of ContentsstLights

Replacing a Side Turn Signal Bulb

3.

LENS

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

4.

Put the bulb holder back into its hole in the lens, and turn it clockwise until it locks.

5.

Turn on the lights to make sure the new bulb is working.

6.

Put the side turn signal assembly back into the body, front first. Push on the back edge until it snaps into place.

BULB

SOCKET

1.

Use a small flat-tipped screwdriver to pry carefully on the back edge of the side turn signal assembly until it pops out of the body.

2.

Turn the bulb holder one-quarter turn counterclockwise to remove it from the lens.

158

Main MenuTable of ContentsstReplacing Rear Bulbs

Lights

1.

Open the trunk.

2.

Remove the fasteners from the trunk lining. To remove a fastener, push on the center of the head until it pops in, then pull the fastener out.

3.

Pull the lining back.

4.

Determine which bulb is burned out: turn signal or back-up light.

5.

Remove the socket by turning it one-quarter turn counterclockwise.

6.

Remove the burned out bulb by pulling it straight out of its socket.

CONTINUED

159

Main MenuTable of ContentsstLights, Cleaning the Seat Belts

7.

Install the new bulb into the socket.

8.

Push the socket into the light assembly, and turn it clockwise until it locks.

9.

Turn on the lights to make sure the new bulb is working.

10.

Install the trunk lining, and secure it with the fasteners. To reinstall a fastener, reset the fastener by pushing on the pointed end until it pops back almost flush with the fingers on the housing. Put the fastener in the hole of the trunk lining, and push on the center until it locks (the center is flush with the head).

160

Cleaning the Seat Belts If your seat belts get dirty, use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. Let the belts air-dry before you use the vehicle.

Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol.

Main MenuTable of ContentsstFloor Mats, Dust and Pollen Filter, Audio Antenna

Floor Mats

The floor mats that came with your vehicle hook over the floor mat anchors. This keeps them from sliding forward and possibly interfering with vehicle operation.

If you remove a floor mat, make sure to re-anchor it when you put it back in your vehicle.

If you use a non-Honda floor mat, make sure it fits properly and that it can be used with the floor mat anchor. Do not put additional floor mats on top of the anchored mat.

Dust and Pollen Filter This filter removes the dust and pollen that is brought in from the outside through the heating and cooling system.

Have your dealer replace the filter when this service is indicated by a maintenance message on the information display. It should be replaced every 15,000 miles (24,000
km) if you drive primarily in urban areas that have high concentrations of soot in the air, or if the flow from the heating and cooling system becomes less than usual.

Audio Antenna

Your vehicle is equipped with an antenna at the right rear f ender. Bef ore using a ‘‘drive-through’’ car wash, remove the antenna by unscrewing it by hand. This prevents the antenna f rom being damaged by the car wash brushes.

161

Main MenuTable of ContentsstWiper Blades

Check the condition of the wiper blades at least every six months. Replace them if you find signs of cracking in the rubber, areas that are getting hard, or if they leave streaks and unwiped areas when used.

To replace a wiper blade: 1.

Raise the wiper arm off the windshield.

LOCK TAB

BLADE

Do not open the hood when the wiper arms are raised, or you will damage the hood and the wiper arms.

2.

Disconnect the blade assembly from the wiper arm by pushing in the lock tab. Hold the lock tab in while you push the blade assembly toward the base of the arm.

3.

Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder.

162

Main MenuTable of Contentsst6.

Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place.

7.

Lower the wiper arm down against the windshield.

Wheels Clean the wheels as you would the rest of the exterior. Wash them with the same solution, and rinse them thoroughly.

Aluminum alloy wheels have a protective clear-coat that keeps the aluminum from corroding and tarnishing. Cleaning the wheels with harsh chemicals (including some commercial wheel cleaners) or a stiff brush can damage the clear-coat. To clean the wheels, use a mild detergent and a soft brush or sponge.

Wiper Blades, Wheels, Tires

Tires To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated.

The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced.

Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.

Follow all instructions in this owner’s manual regarding tire inflation and maintenance.

BLADE

REINFORCEMENT

4.

Examine the new wiper blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade.

5.

Slide the new wiper blade into the holder until the tabs lock.

163

Main MenuTable of ContentsstTires

Inflation Guidelines Keeping the tires properly inflated provides the best combination of handling, tread life, and riding comfort.

Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated.

Overinflated tires can make your vehicleridemoreharshly,are more prone to damage from road hazards, and wear unevenly.

We recommend that you visually check your tires every day. If you think a tire might be low, check it immediately with a tire gauge.

164

Use a gauge to measure the air pressure in each tire at least once a month. Even tires that are in good condition may lose 1 to 2 psi (10 to 20 kPa, 0.1 to 0.2 kgf/cm ) per month. Remember to check the sparetireatthesametime.

Check the air pressures when the tires are cold. This means the vehicle has been parked for at least 3
hours, or driven less than 1 mile (1.6
km). Add or release air, if needed, to match the recommended cold tire pressures on page

165

If you check air pressures when the tires are hot [driven for several miles (kilometers)], you will see readings 4
to 6 psi (30 to 40 kPa, 0.3 to 0.4
kgf/cm ) higher than the cold readings. This is normal. Do not let air out to match the recommended cold air pressure. The tire will be underinflated.

You should use your own tire pressure gauge and use it whenever you check your tire pressures. This will make it easier for you to tell if a pressure loss is due to a tire problem and not due to a variation between gauges.

While tubeless tires have some ability to self-seal if they are punctured, you should look closely for punctures if a tire starts losing pressure.

Main MenuTable of ContentsstRecommended Tire Pressures The following charts show the recommended cold tire pressures for most normal and high-speed driving conditions.

Tire Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. Youshouldlookfor:

Bumps or bulges in the tread or side of the tire. Replace the tire if youfindeitheroftheseconditions.

Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord.

Excessive tread wear.

Front:

Tire Size

215/45R17 87W

Rear:

Tire Size

245/40R17 91W