2007 Honda S2000 Owners Manual

CRUISE BUTTON

1.

Push in the CRUISE button. The indicator over the button comes on.

3.

2.

Accelerate to the desired cruising speed above 25 mph (40 km/h).

SET/decel Press and release the SET/decel button on the steering wheel. The indicator on the instrument panel comes on to show the system is now activated.

Cruise Control

Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for city driving, winding roads, slippery roads, heavy rain, or bad weather.

Improper use of the cruise control can lead to a crash.

Use the cruise control only when traveling on open highways in good weather.

106

Main MenuTable of ContentsstCruise control may not hold the set speed when you are going up and down hills. If your speed increases going down a hill, use the brakes to slow down. This will cancel the cruise control. To resume the set speed, press the RESUME/accel button. The indicator on the instrument panel will come back on.

Cruise Control

Changing the Set Speed You can increase the set cruising speed in any of these ways:

Press and hold the RESUME/ accel button. When you reach the desired cruising speed, release the button.

Push on the accelerator pedal. Accelerate to the desired cruising speed, and press the SET/decel button.

To increase the speed in very small amounts, tap the RESUME/ accel button. Each time you do this, your vehicle speeds up about 1 mph (1.6 km/h).

You can decrease the set cruising speed in any of these ways:

Press and hold the SET/decel button. Release the button when you reach the desired speed.

To slow down in very small amounts, tap the SET/decel button. Each time you do this, your vehicle will slow down about 1 mph (1.6 km/h).

Tap the brake or clutch pedal lightly with your foot. The CRUISE CONTROL indicator on the instrument panel goes out. When the vehicle slows to the desired speed, press the SET/ decel button.

CONTINUED

107

Main MenuTable of ContentsstCruise Control

Even with the cruise control turned on, you can still use the accelerator pedal to speed up for passing. After completing the pass, take your foot off the accelerator pedal. The vehicle will return to the set cruising speed.

Resting your foot on the brake or clutch pedal causes the cruise control to cancel.

Canceling Cruise Control You can cancel cruise control in any of these ways:

Tap the brake or clutch pedal.

Push the CANCEL button on the steering wheel.

Push the CRUISE button.

Resuming the Set Speed When you push the CANCEL button, or tap the brake or clutch pedal, the system will remember the previously set cruising speed. To return to that speed, accelerate to above 25 mph (40 km/h), then press and release the RESUME/accel button. The CRUISE CONTROL indicator comes on. The vehicle will accelerate to the same cruising speed as before.

Pressing the CRUISE button turns the system off and erases the previous cruising speed.

108

Main MenuTable of ContentsstBefore Driving

Before you begin driving your vehicle, you should know what gasoline to use and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your vehicle, please read the information in this section first.

Break-in Period Fuel Recommendation Service Station Procedures

............................. ................. ......... ....................................

Refueling Opening and Closing the

. 110
. 110
. 111
. 111

Hood

Oil Check Engine Coolant Check

. 112
. 113
. 114
Fuel Economy . 114
Accessories and Modifications . 115
Carrying Cargo . 117

....................................... ................................... ............. ............................... ... .............................

109

Main MenustBreak-in Period, Fuel Recommendation

Break-in Period Help assure your vehicle’s future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period:

Avoid full-throttle starts and rapid acceleration. Do not exceed 5,500
rpm for the first 600 miles (1,000
km) of operation.

Do not change the oil until the scheduled maintenance time.

Avoid hard braking for the first 200 miles (300 km).

You should also follow these recommendations with an overhauled or exchanged engine, or when the brakes are replaced.

Fuel Recommendation Your vehicle is designed to operate on premium unleaded gasoline with a pump octane number of 91 or higher. Use of a lower octane gasoline can cause occasional metallic knocking noises in the engine and will result in decreased engine performance. Use of a gasoline with a pump octane number less than 87 can lead to engine damage. We recommend quality gasoline containing detergent additives that help prevent fuel system and engine deposits.

In addition, in order to maintain good performance, fuel economy, and emissions control, we strongly recommend, in areas where it is available, the use of gasoline that does NOT contain manganese-based fuel additives such as MMT.

Use of gasoline with these additives may adversely affect performance,

and cause the malfunction indicator lamp on your instrument panel to come on. If this happens, contact your authorized dealer for service.

Some gasoline today is blended with oxygenates such as ethanol or MTBE. Your vehicle is designed to operate on oxygenated gasoline containing up to 10% ethanol by volume and up to 15% MTBE by volume. Do not use gasoline containing methanol.

If you notice any undesirable operating symptoms, try another service station or switch to another brand of gasoline.

For further important fuel-related information, please refer to your Quick Start Guide

110

Main MenuTable of ContentsstRefueling

Pull

1.

Park with the driver’s side closest to the service station pump.

2.

Open the fuel fill door by pulling on the knob on the driver’s door jamb.

Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel.

Stop the engine, and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately.

FUEL FILL CAP

Service Station Procedures

3.

4.

Remove the fuel fill cap slowly. You may hear a hissing sound as pressure inside the tank escapes. Place the cap in the holder on the fuel fill door.

Stop filling the tank after the fuel nozzle automatically clicks off. Do not try to ‘‘top off’’ the tank. Leave some room for the fuel to expand with temperature changes.

Ifthefuelnozzlekeepsclickingoff even though the tank is not full, there may be a problem with your vehicle’s fuel vapor recovery system. The system helps keep fuel vapor from going into the atmosphere. Try filling at another pump. If this does not fix the problem, consult your dealer.

CONTINUED

111

Main MenuTable of ContentsstService Station Procedures

5.

Screw the fuel fill cap back on until it clicks at least once. If you do not properly tighten the cap, the malfunction indicator lamp may come on (see page will also see a ‘‘CHECK FUEL CAP’’ message on the information display.

). You

187

Opening and Closing the Hood

RELEASE HANDLE

6.

Push the fuel fill door closed until it latches.

112

1.

Park the vehicle, and set the parking brake. Pull the hood release handle located under the lower left corner of the dashboard. The hood will pop up slightly.

2.

Put your fingers under the front edge of the hood near the center. Slide your hand to the left until you feel the hood latch handle. Push this handle to the left to release the hood. Lift up the hood.

If the hood latch handle moves stiffly, or if you can open the hood without lifting the handle, the mechanism should be cleaned and lubricated.

Main MenuTable of ContentsstGRIP

DIPSTICK

Oil Check

Service Station Procedures

SUPPORT ROD

CLIP

3.

Holding the grip, pull the support rod out of its clip. Insert the end into the designated hole in the hood.

To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop. Make sure it is securely latched.

Wait a few minutes after turning the engine off before you check the oil.

1.

Remove the dipstick (black handle).

2.

Wipe off the dipstick with a clean cloth or paper towel.

3.

Insert the dipstick all the way back into its hole.

UPPER MARK

LOWER MARK

4.

Remove the dipstick again, and check the level. It should be between the upper and lower marks.

If it is near or below the lower mark, see 146

Adding Engine Oil

on page

113

Main MenuTable of ContentsstTry to maintain a constant speed. Everytimeyouslowdownand speed up, your vehicle uses extra fuel. Use cruise control when appropriate.

Combine several short trips into one.

The air conditioning puts an extra load on the engine which makes it usemorefuel.Usethefresh-air ventilation when possible.

Service Station Procedures, Fuel Economy

Engine Coolant Check

RESERVE TANK

MAX

MIN

Look at the coolant level in the radiator reserve tank. Make sure it is between the MAX and MIN lines. If Adding it is below the MIN line, see Engine Coolant for 149
information on adding the proper coolant.

on page

Owner’s Maintenance on page

Refer to Checks for information about checking other items on your vehicle.

141

114

Fuel Economy ImprovingFuelEconomy

Always maintain your vehicle according to the maintenance messages displayed on the information display. See Maintenance Checks 141

Owner’s on page

an underinflated tire Forexample, causes more ‘‘rolling resistance,’’ which uses more fuel.

The build-up of snow or mud on your vehicle’s underside adds weight and rolling resistance. Frequent cleaning helps your fuel mileage and reduces the chance of corrosion.

Drive moderately. Rapid acceleration, abrupt cornering, and hard braking use more fuel.

Always drive in the highest gear possible.

Main MenuTable of ContentsstModifying your vehicle, or installing some non-Honda accessories, can make it unsafe. Before you make any modifications or add any accessories, be sure to read the following information.

Accessories Your dealer has Honda accessories that allow you to personalize your vehicle. These accessories have been designed and approved for your vehicle, and are covered by warranty.

Although non-Honda accessories may fit on your vehicle, they may not meet factory specifications, and could adversely affect your vehicle’s handling and stability.

Improper accessories or modifications can affect your vehicle’s handling, stability, and performance, and cause a crash in which you can be hurt or killed.

Follow all instructions in this owner’s manual regarding accessories and modifications.

When properly installed, cellular phones, alarms, two-way radios, and low-powered audio systems should not interfere with your vehicle’s computer controlled systems, such as your airbags and anti-lock brakes.

Accessories and Modifications

Before installing any accessory:

Make sure the accessory does not obscure any lights, or interfere with proper vehicle operation or performance.

Be sure electronic accessories do not overload electrical circuits (see page the proper operation of your vehicle.

) or interfere with

190

Before installing any electronic accessory, have the installer contact your dealer. If possible, have your dealer inspect the final installation.

115

Main MenuTable of ContentsstAccessories and Modifications

Larger or smaller wheels and tires can interfere with the operation of your vehicle’s anti-lock brakes and other systems.

Modifying your steering wheel or any other part of your vehicle’s safety systems could make the systems ineffective.

If you plan to modify your vehicle, consult your dealer.

Modifying Your Vehicle Removing parts from your vehicle, or replacing components with non-Honda components could seriously affect your vehicle’s handling, stability, and reliability.

Here are some examples:

Lowering the vehicle with a non- Honda suspension kit that significantly reduces ground clearance can allow the undercarriage to hit speed bumps or other raised objects, which could cause the airbags to deploy.

Raising your vehicle with a non-Honda suspension kit can affect the handling and stability.

Non-Honda wheels can cause excessive stress on suspension components.

116

Main MenuTable of ContentsstUPPER AND LOWER CONSOLE COMPARTMENTS

DOOR POCKETS

TRUNK

SEAT-BACK POCKET

CONSOLE SIDE NET

DASHBOARD LOWER POCKET

Carrying Cargo

Your vehicle has several convenient storage areas:

Upper and lower console compartments

Dashboard lower pocket

Door pockets

Console side net

Seat-back pocket

Trunk

However, carrying too much cargo, or improperly storing it, can affect your vehicle’s handling, stability, stopping distance, and tires, which may make it unsafe. Before carrying any type of cargo, be sure to read the following pages.

117

Main MenuTable of ContentsstCarrying Cargo

Load Limits The maximum load for your vehicle is 400 lbs (181 kg) for U.S. vehicles, and 185 kg for Canadian vehicles. This figure includes the total weight of all occupants, cargo, and accessories.

Overloading or improper loading can affect handling and stability and cause a crash in which you can be hurt or killed.

Follow all load limits and other loading guidelines in this manual.

118

Steps for Determining Correct Load Limit:

4.

1.

2.

3.

Locate the statement, ‘‘the combined weight of occupants and cargo should never exceed 400
lbs’’ on your vehicle’s placard. [The placard is on the driver’s doorjamb.]

Determine the combined weight of the driver and passenger that will be riding in your vehicle.

Subtract the combined weight of the driver and passenger from 400
lbs.

The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the maximum load is 400 lbs and there will be two 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 100 lbs. 150) = 100 lbs.] [400

300 (2

−

×

5.

Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4.

In addition, the total weight of the vehicle, all occupants, accessories and cargo must not exceed the gross vehicle weight rating (GVWR) or the gross axle weight rating (GAWR). Both are on a label on the driver’s doorjamb.

Main MenuTable of ContentsstCarrying Items in the Passenger Compartment

Store or secure all items that could be thrown around and hurt someone during a crash.

Carrying Cargo in the Trunk

Distribute cargo evenly on the floor of the trunk, placing the heaviest items on the bottom and as far forward as possible.

Be sure items placed on the floor behind the front seats cannot roll under the seats and interfere with the driver’s ability to operate the pedals, the proper operation of the seats, or proper operation of the sensors under the seats.

Carrying Cargo

119

Main MenuTable of ContentsstThis section gives you tips on starting the engine under various conditions, and how to operate the manual transmission. It also includes important information on parking your vehicle and the braking system.

Driving

Driving Guidelines Preparing to Drive Starting the Engine Manual Transmission Parking Braking System Anti-lock Brakes (ABS) Vehicle Stability Assist (VSA)

........................ ........................ ....................... ................... ........................................... ............................. ...............

. 122
. 123
. 124
. 125
. 127
. 127
. 128

System

Towing a Trailer

........................................ ...........................

. 130
. 131

121

Main MenustBecause of the low-profile tires fitted to your vehicle, the alloy wheels are closer to the ground. Driving over a pothole or road debris at too high a speed can seriously damage a wheel. Slow down under these conditions.

Driving Guidelines

Your vehicle is designed to give you optimum handling and performance on well-maintained roads. As part of this design, your vehicle has a minimum of ground clearance and very low-profile tires.

Use caution if you ever drive your vehicle on very rough or rutted roads. You could damage the suspension and underbody by bottoming out. Going too fast over parking lot ‘‘speed bumps’’ can also cause damage.

122

Curbs and steep inclines could damage the front and rear bumpers. Low curbs that do not affect the average vehicle may be high enough to hit the bumper on your vehicle. The front or rear bumper may scrape when trying to drive onto an incline, such as a steep driveway or trailer ramps.

Main MenuTable of ContentsstPreparing to Drive

Check that any items you may be carrying are stored properly or fastened down securely.

9.

Fasten your seat belt. Check that your passenger has fastened his or her seat belt (see page

12

).

Youshoulddothefollowingchecks and adjustments before you drive your vehicle.

1.

Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice.

2.

Check that the hood is fully closed.

5.

6.

7.

Check the seat adjustment (see page

67

).

Check the adjustment of the inside and outside mirrors (see page

75

).

3.

Check that the trunk is fully closed.

8.

Make sure the doors are securely closed and locked.

4.

Visually check the tires. If a tire looks low, use a gauge to check its pressure.

10.

When you start the engine, check the gauges and indicators in the instrument panel (see page ).

45

123

Main MenuTable of ContentsstStarting theEngine

1.

Apply the parking brake.

2.

3.

In cold weather, turn off all electrical accessories to reduce the drain on the battery.

Push the clutch pedal down all the way. The ENGINE START button has no effect unless the clutch pedal is pressed.

4.

Turn the ignition key to the ON (II) position.

5.

Without touching the accelerator pedal, push the ENGINE START button. Do not hold the ENGINE START button for more than 15
seconds at a time. If the engine does not start right away, pause for at least 10 seconds before trying again.

124

6.

7.

Iftheenginedoesnotstartwithin 15 seconds, or starts but stalls right away, repeat step 5 with the accelerator pedal pressed halfway down. If the engine starts, release pressure on the accelerator pedal so the engine does not race.

If the engine fails to start, press the accelerator pedal all the way downandholdittherewhile starting to clear flooding. If the engine still does not start, return to step 6.

The engine is harder to start in cold weather. Also, the thinner air found at altitudes above 8,000 feet (2,400
meters) adds to this problem.

ENGINE START BUTTON

The immobilizer system protects your vehicle f rom thef t. If an improperly- coded key (or other device) is used, the engine’s f uel system is disabled. For more inf ormation, see page

.61

Main MenuTable of ContentsstCome to a full stop before you shift into reverse. You can damage the transmission by trying to shift into reverse with the vehicle moving. Push down the clutch pedal, and pause for a few seconds before shifting into reverse, or shift into one of the forward gears for a moment. This stops the gears so they won’t ‘‘grind.’’

When slowing down, you can get extra braking from the engine by shifting to a lower gear. This extra braking can help you maintain a safe speed and prevent your brakes from overheating while going down a steep hill. Before downshifting, make sure the engine speed will not go into the tachometer’s red zone in the lower gear.

Manual Transmission

Rapid slowing or speeding up can cause loss of control on slippery surfaces. If you crash, you can be injured.

Use extra care when driving on slippery surfaces.

Your vehicle is equipped with an aluminum shift lever. If you leave the vehicle parked outside for a long time on a hot day, be careful before moving the shift lever. Because of the heat, the shift lever may be extremely hot. If the outside temperature is low, the shift lever feels cold.

125

The manual transmission is synchronized in all forward gears for smooth operation. It has a lockout so you cannot shift directly from fifth to reverse instead of sixth (see page ). When shifting up or down, 126
make sure you push the clutch pedal down all the way, shift to the next gear, and let the pedal up gradually. When you are not shifting, do not rest your foot on the clutch pedal. This can cause your clutch to wear out faster.

Main MenuTable of ContentsstManual Transmission

Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you good fuel economy and effective emissions control. The following shift points are recommended:

Shift Up

Normal Acceleration

1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th 5th to 6th

15 mph (24 km/h) 25 mph (40 km/h) 40 mph (64 km/h) 47 mph (75 km/h) 52 mph (83 km/h)

Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer’s red zone. If this occurs, you may feel the engine cut in and out. This is caused by a limiter in the engine’s computer controls. The engine will run normally when you reduce the rpm below the red zone.

Before downshifting, make sure the engine will not go into the tachometer’s red zone.

Reverse Lockout

The manual transmission has a lockout so you cannot accidentally shift from fifth to reverse instead of sixth while the vehicle is moving.

With the clutch pedal pressed, move the shift lever to the reverse side of the neutral gate. Then push the shift lever down, and shift to reverse.

126

Main MenuTable of ContentsstIf the vehicle is facing uphill, turn the front wheels away from the curb, and put the transmission in first gear.

If the vehicle is facing downhill, turn the front wheels toward the curb, and put the transmission in reverse gear.

Make sure the parking brake is fully released before driving away. Driving with the parking brake partially set can overheat or damage the rear brakes.

Parking Always use the parking brake when you park your vehicle. Make sure the parking brake is set firmly, or your vehicle may roll if it is parked on an incline.

Parking Tips

Make sure the convertible top and the windows are closed.

Turn off the lights.

Place any packages, valuables, etc., in the trunk or take them with you.

Lock the doors.

Never park over dry leaves, tall grass, or other flammable materials. The hot three way catalytic converter could cause these materials to catch on fire.

Parking, Braking System

Braking System Your vehicle is equipped with disc brakes at all four wheels. A power assist helps reduce the effort needed on the brake pedal. The anti-lock brake system (ABS) helps you retain steering control when braking very hard. Resting your foot on the pedal keeps the brakes applied lightly, builds up heat, and reduces their effectiveness. It also keeps your brake lights on all the time, confusing drivers behind you.

Constant application of the brakes when going down a long hill builds up heat and reduces their effective- ness. Use the engine to assist the brakes by taking your foot off the accelerator and downshifting to a lower gear.

CONTINUED

127

Main MenuTable of ContentsstBraking System, Anti-lock Brakes (ABS)

Check the brakes after driving through deep water. Apply the brakes moderately to see if they feel normal. If not, apply them gently and frequently until they do. Be extra cautious in your driving.

Braking System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels.

Brake Pad Wear Indicators If the brake pads need replacing, you will hear a distinctive, metallic screeching sound when you apply the brake pedal. If you do not have the brake pads replaced, they will screech all the time. It is normal for the brakes to occasionally squeal or squeak when you apply them.

Anti-lock Brakes (ABS) The anti-lock brake system (ABS) helps prevent the brakes from locking up, and helps you retain steering control by pumping the brakes rapidly, much faster than a person can do it.

The ABS also balances the front-to- rear braking distribution according to vehicle loading.

Youshouldneverpumpthebrakepedal. Let the ABS work for you by always keeping firm, steady pressure on the brake pedal. This is sometimes referred to as ‘‘stomp and steer.’’

You will feel a pulsation in the brake pedal when the ABS activates, and may hear some noise. This is normal: it is the ABS rapidly pumping the brakes. On dry pavement, you will need to press on the brake pedal very hard before the ABS activates. However, you may feel the ABS activate immediately if you are trying to stop on snow or ice.

128

Main MenuTable of ContentsstABS Indicator

ANTI-LOCK BRAKE SYSTEM INDICATOR

Important Safety Reminders ABS does not reduce the time or distance it takes to stop the vehicle; control during braking.

it only helps with steering

A vehicle with ABS may require a longer distance to stop on loose or uneven surfaces, such as gravel or snow, than a vehicle without anti- lock.

Anti-lock Brakes (ABS)

ABS will not prevent a skid that results from changing direction abruptly, such as trying to take a corner too fast or making a sudden lane change.

ABS cannot prevent a loss of stability. Always steer moderately when you are braking hard. Severe or sharp steering wheel movement can still cause your vehicle to veer into oncoming traffic or off the road.

If this indicator comes on, the anti- lock function of the braking system has shut down. The brakes still work like a conventional system, but without anti-lock. You should have your dealer inspect your vehicle as soon as possible.

129

Main MenuTable of ContentsstWithout VSA, your vehicle still has normal braking and cornering ability, but it does not have VSA traction and stability enhancement.

Vehicle Stability Assist (VSA) System

VSA Activation Indicator

When VSA activates, you will see the VSA activation indicator blink (see page

50

).

VSA System Indicator

If this indicator comes on while driving, pull to the side of the road when it is safe, and turn off the engine. Reset the system by restarting the engine. If the VSA system indicator stays on, or comes back on while driving, have the VSA system inspected by your dealer.

If the indicator does not come on when the ignition switch is turned to the ON (II) position, there may be a problem with the VSA system. Have your dealer inspect your vehicle as soon as possible (see page

50

).

The vehicle stability assist (VSA) system helps to stabilize the vehicle during cornering if the vehicle turns more or less than desired. It also assists you in maintaining traction while accelerating on loose or slippery road surfaces. It does this by regulating the engine’s output and by selectively applying the brakes.

When VSA activates, you may notice that the engine does not respond to the accelerator in the same way it does at other times.

The VSA system cannot enhance the vehicle’s driving stability in all situations and does not control your vehicle’s entire braking system. It is still your responsibility to drive and corner at reasonable speeds and to leave a sufficient margin of safety.

130

Main MenuTable of ContentsstVehicle Stability Assist (VSA) System, Towing a Trailer

Immediately after freeing your vehicle, be sure to switch the VSA on again. We do not recommend driving your vehicle with the VSA and traction control systems switched off.

This switch is at the left side of the right vent. Press it to turn VSA on and off.

When VSA is off, the VSA activation indicator comes on as a reminder.

VSA is turned on every time you start the engine, even if you turned it off the last time you drove the vehicle.

VSA Off Switch

VSA OFF SWITCH

In certain unusual conditions when your vehicle gets stuck in shallow mud or fresh snow, it may be easier to free it with the VSA temporarily switched off. When the VSA system is off, the traction control system is also off. You should only attempt to free your vehicle with the VSA off if you are not able to free it when the VSA is on.

VSA and Tire Sizes Driving with varying tire or wheel sizes may cause the VSA to malfunction. When replacing tires, make sure they are of the same size and type as your original tires (see page

165

).

Deactivate the VSA system if you need to drive with the compact spare tire installed (see page

174

).

If you install winter tires, make sure they are the same size as those that were originally supplied with your vehicle. Exercise the same caution during winter driving as you would if your vehicle was not equipped with VSA.

Towing a Trailer Your vehicle is not designed to tow a trailer; Attempting to do so can void your warranties.

131

Main MenuTable of ContentsstThis section explains why it is important to keep your vehicle well maintained and how to follow basic maintenance safety precautions.

This section also includes instructions on how to read the maintenance minder messages on the information display, a maintenance record, and instructions for simple maintenance tasks you may want to take care of yourself.

If you have the skills and tools to perform more complex maintenance tasks on your vehicle, you may want to purchase the service manual. See page for information on how to obtain a copy, or see your dealer.

215

Maintenance

Maintenance Safety Maintenance Minder Maintenance Record Fluid Locations Adding Engine Oil Changing the Oil and Filter Engine Coolant Windshield Washers Manual Transmission Fluid Differential Fluid Brake and Clutch Fluid Lights Cleaning the Seat Belts Floor Mats Dust and Pollen Filter Audio Antenna Wiper Blades Wheels Tires Checking the Battery Vehicle Storage

...................... .................... .................... .............................. ........................ ......... .............................. .................... ........ .......................... ................ ............................................. ................ ..................................... .................. .............................. ................................. ........................................... ............................................... ................... .............................

. 134
. 135
. 143
. 145
. 146
. 147
. 149
. 151
. 152
. 153
. 154
. 155
. 160
. 161
. 161
. 161
. 162
. 163
. 163
. 169
. 171

133

Main MenustMaintenance Safety

All service items not detailed in this section should be performed by a certified technician or other qualified mechanic.

Important Safety Precautions To eliminate potential hazards, read the instructions before you begin, and make sure you have the tools and skills required.

Make sure your vehicle is parked on level ground, the parking brake is set, and the engine is off.

To clean parts, use a commercially available degreaser or parts cleaner, not gasoline.

To reduce the possibility of fire or explosion, keep cigarettes, sparks, and flames away from the battery and all fuel-related parts.

Wear eye protection and protective clothing when working with the battery or compressed air.

134

Improperly maintaining this vehicle, or failing to correct a problem before driving can cause a crash in which you can be seriously hurt or killed.

Always follow the inspection and maintenance recommendations and schedules in this owner’s manual.

Potential Vehicle Hazards Carbon Monoxide poison from engine exhaust. there is adequate ventilation whenever you operate the engine.

Be sure

Burns from hot parts. Let the engine and exhaust system cool down before touching any parts.

Injury from moving parts. not run the engine unless instructed to do so.

Do

Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.

Always follow the procedures and precautions in this owner’s manual.

Some of the most important safety precautions are given here. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.

Main MenuTable of ContentsstYour vehicle displays engine oil life and maintenance service items on the information display to show you when you should have your dealer do engine oil replacement and indicated maintenance service.

Based on the engine operating conditions and accumulated engine revolutions, the onboard computer in your vehicle calculates the remaining engine oil life and displays it as a percentage.

Maintenance Minder

Engine Oil Life Display

TRIP BUTTON

The remaining engine oil life is shownonthedisplayaccordingto this table:

Calculated Engine

Displayed

ENGINE OIL LIFE DISPLAY

To see the current engine oil life, turn the ignition switch to the ON (II) position, and push and release the TRIP button repeatedly until the engine oil life display appears (see page

51

).

Oil Life (%) 91 % 100 % 90 % 81 % 71 % 80 % 61 % 70 % 51 % 60 % 41 % 50 % 40 % 31 % 21 % 30 % 16 % 20 % 11 % 15 % 6 % 10 % 5 % 1 %

− − − − − − − − − − − − 0 %

Engine Oil Life (%)

100 % 90 % 80 % 70 % 60 % 50 % 40 % 30 % 20 % 15 % 10 % 5 % 0 %

CONTINUED

135

Main MenuTable of ContentsstThe maintenance item code or codes indicate the main and sub items required at the time of the oil change (see page

142

).

The 15 and 10 percent oil life indicator reminds you that the time is coming soon to take your vehicle in for the required maintenance.

Maintenance Minder

MAINTENANCE MINDER INDICATOR

ENGINE OIL LIFE INDICATOR

MAINTENANCE ITEM CODE(S)

If the remaining engine oil life is 15
to 6 percent, you will see the engine oil life indicator every time you turn the ignition switch to the ON (II) position. The maintenance minder indicator will also come on, and the maintenance item code(s) for other scheduled maintenance items needing service will be displayed next to the engine oil life indicator.

136

Main MenuTable of ContentsstMaintenance Minder

When the remaining engine oil life is 5 to 1 percent, you will see a ‘‘SERVICE OIL LIFE’’ message along with the same maintenance item code(s), every time you turn the ignition switch to the ON (II) position. The maintenance minder indicator ( ) also comes on and remains on in the instrument panel.

When the remaining engine oil life is 0 percent, the engine oil life indicator will blink. The display comes on every time you turn the ignition switch to the ON (II) position. The maintenance minder indicator on in the instrument panel. When you see this message, immediately have the indicated maintenance done by your dealer.

) also comes on and remains

If you do not perform the indicated maintenance, negative mileage is displayed and begins to blink after the vehicle has been driven 10 miles (10 km) or more.

Negative mileage means your vehicle has passed the maintenance required point. Immediately have the indicated maintenance done by your dealer.

CONTINUED

137

Main MenuTable of ContentsstMaintenance Minder

The maximum total mileage shown is ‘‘ 9999.’’

−

You can change the information display from the engine oil life display to the odometer, the trip meter, or the outside temperature every time you press and release the TRIP button.

When the engine oil life is 0 percent or negative mileage, the maintenance minder indicator change the information display.

)remainsonevenifyou

Immediately have the service done, and make sure to reset the display as described on the next page.

Maintenance Main Items and Sub Items

MAINTENANCE SUB ITEM (S)

ENGINE OIL LIFE INDICATOR

MAINTENANCE MAIN ITEM

All maintenance items displayed in the information display are in code. For an explanation of these maintenance codes, see page

142

138

Main MenuTable of ContentsstResetting the Engine Oil Life Indicator Your dealer will reset the display after completing the required maintenance service. You will see ‘‘OIL LIFE 100%’’ on the information display the next time you turn the ignition switch to the ON (II) position.

If maintenance service is done by someone other than your dealer, reset the maintenance minder as follows:

1.

Turn the ignition switch to the ON (II) position.

2.

Press the TRIP button until the engine oil life indicator is displayed.

Maintenance Minder

ENGINE OIL LIFE INDICATOR

ENGINE OIL LIFE INDICATOR

3.

Press the TRIP button for about 10 seconds. The engine oil life indicator and the maintenance item code(s) will blink.

4.

Press the TRIP button for about 5
seconds. The maintenance items code(s) will disappear, and the engine oil life will reset to ‘‘100.’’

139

Main MenuTable of ContentsstMaintenance Minder

Important Maintenance Precautions If you have the required service done but do not reset the display, or reset the display without doing the service, the system will not show the proper maintenance intervals. This can lead to serious mechanical problems because you will no longer have an accurate record of when maintenance is needed.

Your authorized Honda dealer knows your vehicle best and can provide competent, efficient service.

However, service at a dealer is not mandatory to keep your warranties in effect. Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Make sure to have the service facility or person reset the display as previously described. Keep all receipts as proof of completion, and have the person who does the work fill out the maintenance record. Check your warranty booklet for more information.

We recommend using Honda parts and fluids whenever you have maintenance done. These are manufactured to the same high quality standards as the original components, so you can be confident of their performance and durability.

140

Main MenuTable of ContentsstU.S. Vehicles: Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are ‘‘certified’’ to EPA standards.

＃

According to state and federal regulations, failure to perform maintenance on the items marked with will not void your emissions warranties. However, all maintenance services should be performed in accordance with the intervals indicated by the information display.

Maintenance Minder

−

Lights Check the operation of the headlights, parking lights, taillights, high-mount brake light, and license plate lights monthly. See page

155

Owner’s Maintenance Checks Youshouldcheckthefollowing items at the specified intervals. If you are unsure of how to perform any check, turn to the appropriate page listed.

Engine oil level Check every time you fill the fuel tank. See page

113

−

Engine coolant level Check the radiator reserve tank every time youfillthefueltank.Seepage

114

−

Brakes and clutch Check the fluid level monthly. See page 154

−

−

Tires Check the tire pressure monthly. Examine the tread for wear and foreign objects. See page 164

CONTINUED

141

Main MenuTable of ContentsstSymbol

Maintenance Minder

Symbol

Maintenance Main Items

Replace engine oil ＊ Replace engine oil and oil filter Inspect front and rear brakes Check parking brake adjustment Inspect these items:

Tie rod ends, steering gear box, and boots Suspension components Driveshaft boots Brake hoses and lines (including ABS) All fluid levels and condition of fluids Exhaust system ＃ Fuel lines and connections ＃

＊

1 :

If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is reset, change the engine oil every year.

See information on maintenance and emissions warranty on page

141

Independent of the maintenance minder messages, replace the brake fluid every 3 years. Inspect idle speed every 160,000 miles (256,000 km). Adjust the valves during services A, B, 1, 2, or 3 if they are noisy.

＃

NOTE:

142

Maintenance Sub Items

Check tire inflation and condition Replace air cleaner element

If you drive in dusty conditions, replace every 15,000
miles (24,000 km).

Replace dust and pollen filter

If you drive primarily in urban areas that have high concentrations of soot in the air from industry and from diesel-powered vehicles, replace every 15,000
miles (24,000 km).

Inspect drive belt Replace transmission fluid Replace spark plugs Inspect valve clearance Replace engine coolant Replace rear differential fluid

Driving in mountainous areas results in higher level of mechanical (shear) stress to fluid. This requires differential fluid changes more frequently than recommended by the maintenance minder. If you regularly drive your vehicle under these conditions, have the differential fluid changed every 15,000 miles (24,000 km).

Main MenuTable of ContentsstYou or the servicing dealer can record all completed maintenance here. When maintenance is performed, record the mileage, circle the coded item(s) completed, and write in any other non-coded items (such as brake fluid replacement) below the codes. Keep the receipts for all work done on your vehicle. Maintenance can also be recorded in your Honda service history booklet.

Mileage

Maintenance Performed

Signature

Date

Mileage

Maintenance Performed

Signature

Date

Maintenance Record

mi km

mi km

mi km

mi km

mi km

mi km

mi km

A B 1

A B 1

A B 1

A B 1

A B 1

A B 1

A B 1

mi km

mi km

mi km

mi km

mi km

mi km