2013 Honda Odyssey Owners Manual

at sustained high speeds (over 99 mph or 160 km/h), adjust the cold tire pressures as shown below to avoid excessive heat build up and sudden tire failure.

Tire Size Pressure

Tire Size Pressure

P235/65R17 103T Front: 33 psi (230 kPa, 2.3 kgf/cm2) Rear: 35 psi (240 kPa, 2.4 kgf/cm2)

P235/60R18 102T Front: 35 psi (240 kPa, 2.4 kgf/cm2) Rear: 36 psi (250 kPa, 2.5 kgf/cm2)

367

uuChecking and Maintaining TiresuTire and Wheel Replacement

Tire and Wheel Replacement Replace your tires with radials of the same size, load range, speed rating, and maximum cold tire pressure rating (as shown on the tire’s sidewall). Using tires of a different size or construction can cause the ABS and VSA® (vehicle stability assist) system to work incorrectly.

It is best to replace all four tires at the same time. If that isn’t possible, replace the front or rear tires in pairs.

1Tire and Wheel Replacement

3WARNING

Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.

If you replace a wheel, only use TPMS specified wheels approved for your vehicle. Make sure that the wheel’s specifications match those of the original wheels.

Always use the size and type of tires recommended in this owner’s manual.

368

uuChecking and Maintaining TiresuTire Rotation

Tire Rotation Rotating tires according to the maintenance messages on the information display */ multi-information display * helps to distribute wear more evenly and increase tire life.

■ Tires without rotation marks

Rotate the tires as shown here.

1Tire Rotation

Tires with directional tread patterns should only be rotated front to back (not from one side to the other). Directional tires should be mounted with the rotation indication mark facing forward, as shown below.

Front

FRONT

Rotation Mark

■ Tires with rotation marks

Rotate the tires as shown here.

Front

* Not available on all models

369

uuChecking and Maintaining TiresuWinter Tires

Winter Tires If driving on snowy or frozen roads, mount all season marked “M+S” tires, snow tires, or tire chains; reduce speed; and maintain sufficient distance between vehicles when driving.

Be particularly careful when operating the steering wheel or brakes to prevent skidding.

Use tire chains, snow tires, or all season tires when necessary or according to the law.

When mounting, refer to the following points.

For winter tires: • Select the size and load ranges that are the same as the original tires. • Mount the tires to all four wheels. For tire chains: • Install them on the front tires only. • Because your vehicle has limited tire clearance, we strongly recommend using the

chains listed below: Cable-type: SCC Super Z-6# SZ-429

• Follow the chain manufacturer's instruction when installing. Mount them as

tightly as you can.

• Check that the chains do not touch the brake lines or suspension. • Drive slowly.

1Winter Tires

3WARNING

Using the wrong chains, or not properly installing chains, can damage the brake lines and cause a crash in which you can be seriously injured or killed.

Follow all instructions in this owner's manual regarding the selection and use of tire chains.

NOTICE Traction devices that are the wrong size or improperly installed can damage your vehicle's brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.

When tire chains are mounted, follow the chain manufacturer's instructions regarding vehicle operational limits.

If your vehicle is equipped with summer tires, be aware that these tires are not designed for winter driving conditions. For more information, contact a dealer.

370

Battery

Checking the Battery

The battery condition is being monitored by the sensor on the negative terminal. If there is a problem with the sensor, the warning message on information display*/multi- information display * will let you know. Have your vehicle checked by a dealer.

Check the battery terminals for corrosion monthly.

If your vehicle's battery is disconnected or goes dead: • The audio system is disabled.

2 Reactivating the audio system P. 196

• The clock resets.

2 Setting the Clock P. 108

• The navigation system * is disabled.

2 Refer to the navigation system manual

Charging the Battery Disconnect both battery cables to prevent damaging your vehicle's electrical system. Always disconnect the negative (–) cable first, and reconnect it last.

1Battery

3WARNING

The battery gives off explosive hydrogen gas during normal operation.

A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.

When conducting any battery maintenance, wear protective clothing and a face shield, or have a skilled technician do it.

WARNING: Battery post, terminals, and related accessories contain lead and lead compounds. Wash your hands after handling.

When you find corrosion, clean the battery terminals by applying a baking powder and water solution. Clean terminals with a damp towel. Cloth/towel dry the battery. Coat the terminals with grease to help prevent future corrosion.

* Not available on all models

371

Remote Transmitter Care

Replacing the Button Battery If the indicator does not come on when the button is pressed, replace the battery.

1Replacing the Button Battery

Battery type: CR1616

1. Unscrew the cover with a small Phillips- head screwdriver. Press a button to pry open the transmitter.

NOTICE An improperly disposed of battery can damage the environment. Always confirm local regulations for battery disposal.

Replacement batteries are commercially available or at a dealer.

Screw

Tab

2. Open the keypad.

u Separate the inner cover from the

keypad by releasing the two tabs on the cover.

3. Make sure to replace the battery with the

correct polarity.

Keypad

Battery

372

Models with power sliding door

Keypad

Battery

uuRemote Transmitter CareuReplacing the Button Battery

Battery type: CR2025

1. Unscrew the cover with a small Phillips- head screwdriver. Press a button to pry open the transmitter.

1Replacing the Button Battery

NOTICE An improperly disposed of battery can damage the environment. Always confirm local regulations for battery disposal.

Replacement batteries are commercially available or at a dealer.

Screw

Tab

2. Open the keypad.

u Separate the inner cover from the

keypad by releasing the two tabs on the cover.

3. Make sure to replace the battery with the

correct polarity.

373

Remote Control and Wireless Headphone Care *

Models with Rear Entertainment System Replacing the Battery ■ Remote Control If it takes several pushes on the remote control buttons to operate the rear entertainment system.

Battery type: BR3032

1. Remove the cover. 2. Make sure to replace the battery with the

correct polarity.

1Replacing the Battery

NOTICE An improperly disposed of battery can damage the environment. Always confirm local regulations for battery disposal.

Replacement batteries are commercially available or at a dealer.

374

* Not available on all models

uuRemote Control and Wireless Headphone Care *uReplacing the Battery

■ Wireless Headphone If there is no sound coming from the wireless headphone, replace the battery.

Battery type: AAA

Coin

1. To open the cover, insert a coin in the slot and twist it slightly to pry the cover away from the earpiece.

Cover

2. Make sure to replace the battery with the

correct polarity.

Battery

375

Heating and Cooling System*/Climate Control System* Maintenance

Dust and Pollen Filter The heating and cooling system/climate control system is equipped with a dust and pollen filter that collects pollen, dust, and other debris in the air. The Maintenance MinderTM messages will let you know when to replace the filter.

We recommend that you replace the dust and pollen filter sooner when using your vehicle in areas with high concentrations of dust.

1Dust and Pollen Filter

If the airflow from the heating and cooling system/ climate control system deteriorates noticeably, and the windows fog up easily, the filter may need to be replaced. Please contact a dealer for replacement.

376

* Not available on all models

Cleaning

Interior Care Use a damp cloth with a mixture of mild detergent and warm water to remove dirt. Use a clean cloth to remove detergent residue.

■ Cleaning Seat Belts Use a soft brush with a mixture of mild soap and warm water to clean the seat belts. Let the belts air dry. Wipe the openings of the seat belt anchors using a clean cloth.

Opening

Continued

1Interior Care

Do not spill liquids inside the vehicle. Electrical devices and systems may malfunction if liquids are splashed on them.

Do not use silicone based sprays on electrical devices such as audio devices and switches. Doing so may cause the items to malfunction or a fire inside the vehicle. If a silicone based spray is inadvertently used on electrical devices, consult a dealer.

Depending on their composition, chemicals and liquid aromatics may cause discoloration, wrinkles, and cracking to resin-based parts and textiles. Do not use alkali solvents or organic solvents such as benzene or gasoline.

After using chemicals, make sure to gently wipe them off using a dry cloth. Do not place used cloths on top of resin based parts or textiles for long periods of time without washing.

377

uuCleaninguInterior Care

■ Floor Mats

Front (Driver Side)

To Unlock

Rear

To Unlock

1Floor Mats

If you use any floor mats that were not originally provided with your vehicle, make sure they are designed for your specific vehicle, fit correctly, and are securely anchored by the floor anchors. Position the rear seat floor mat properly. If they are not properly positioned, the floor mat can interfere with the front seat functions.

The front and second row passenger’s floor mats hook over the floor anchors, which keep the mats from sliding forward. To remove a mat for cleaning, turn the anchor knobs to the unlock position. When reinstalling the mat after cleaning, turn the knobs to the lock position.

Do not put additional floor mats on top of the anchored mats.

■ Maintaining Genuine Leather* Vacuum dirt and dust from the leather frequently. Pay close attention to the pleats and seams. Clean the leather with a soft cloth dampened with a 90% water and 10% neutral soap solution. Then buff it with a clean, dry cloth. Remove any dust or dirt on leather surfaces immediately.

378

* Not available on all models

Exterior Care Dust off the vehicle body after you drive. Regularly inspect your vehicle for scratches on painted surfaces. A scratch on a painted surface can result in body rust. If you find a scratch, promptly repair it.

■ Washing the Vehicle Wash the vehicle regularly. Wash more frequently when driving in the following conditions: • If driving on roads with road salt. • If driving in coastal areas. • If tar, soot, bird droppings, insects, or tree sap are stuck to painted surfaces.

■ Using an Automated Car Wash Fold in the door mirrors. Make sure to follow the instructions indicated on the automated car wash.

■ Using High Pressure Cleaners • Keep sufficient distance between the cleaning nozzle and the vehicle body. • Take particular care around the windows. Standing too close may cause water to

enter the vehicle interior. Do not spray water into the engine compartment.

Continued

uuCleaninguExterior Care

1Washing the Vehicle

Do not spray water into the air intake vents or engine compartment. It can cause a malfunction.

Air Intake Vents

379

uuCleaninguExterior Care

■ Applying Wax A good coat of automotive body wax helps protect your vehicle’s paint from the elements. Wax will wear off over time and expose your vehicle’s paint to the elements, so reapply as necessary.

1Applying Wax

NOTICE Chemical solvents and strong cleaners can damage the paint, metal, and plastic on your vehicle. Wipe up spills immediately.

■ Maintaining the Bumpers and Other Resin Coated Parts If you get gasoline, oil, engine coolant, or battery fluid on resin coated parts, they may be stained or the coating may peel. Promptly wipe it away using a soft cloth and clean water.

1Maintaining the Bumpers and Other Resin Coated Parts

Ask a dealer about the correct coating material when you want to repair the painted surface of the parts made of resin.

■ Cleaning the Window Wipe using a glass cleaner.

■ Maintaining Aluminum Wheels* Aluminum is susceptible to deterioration caused by salt and other road contaminants. Use a sponge and mild detergent to wipe away promptly. Be careful not to use harsh chemicals (including some commercial wheel cleaners) or a stiff brush. They can damage the clear coat of the aluminum alloy wheels that helps keep the aluminum from corroding and tarnishing.

1Cleaning the Window

Wires are mounted to the inside of the rear window. Wipe along the same direction as the wires with a soft cloth so as not to damage them.

380

* Not available on all models

Handling the Unexpected

This chapter explains how to handle unexpected troubles.

Tools

Types of Tools.................................. 382

If a Tire Goes Flat

Changing a Flat Tire......................... 383

Engine Does Not Start

Checking the Engine........................ 392
Jump Starting.................................... 393
Shift Lever Does Not Move.............. 395
Overheating

How to Handle Overheating............. 396

Indicator, Coming On/Blinking

If the Low Oil Pressure Indicator Comes On ............................................. 398
If the Charging System Indicator Comes On ................................................. 398
If the Malfunction Indicator Lamp Comes On or Blinks ................................... 399
If the Brake System Indicator Comes On.......400
If the Low Tire Pressure Indicator Comes On ................................................. 401
If the TPMS Indicator Comes On ...... 401

If the Low Tire Pressure/TPMS Indicator Comes On or Blinks ....................... 402

Fuses

Fuse Locations ................................. 403
Inspecting and Changing Fuses........ 408
Emergency Towing........................... 409
When You Cannot Open or Close the Tailgate............................................ 410

381

Tools

Types of Tools

1Types of Tools

The tools were stored under the second row seat.

Jack

Wheel Nut Wrench/

Jack Handle

Jack Handle Bar

Bracket

Mounting Wing

Bolt (B)

Mounting Wing

Bolt (A)

Storage Bag

382

If a Tire Goes Flat

Changing a Flat Tire If a tire goes flat while driving, grasp the steering wheel firmly, and brake gradually to reduce speed. Then, stop in a safe place. Replace the flat tire with a compact spare tire. Go to a dealer as soon as possible to have the full-size tire repaired or replaced.

1. Park the vehicle on firm, level, non-slippery surface and apply the parking brake. 2. Move the shift lever to (P. 3. Turn on the hazard warning lights and turn the ignition switch to LOCK (0.

1Changing a Flat Tire

Periodically check the tire pressure of the compact spare. It should be set to the specified pressure. Specified Pressure: 60 psi (420 kPa, 4.2 kgf/cm2)

When driving with the compact spare tire, keep the vehicle speed under 50 mph (80 km/h). Replace with a full-size tire as soon as possible.

The compact spare tire and wheel in your vehicle are specifically for this model. Do not use them with another vehicle. Do not use another type of compact spare tire or wheel with your vehicle.

Do not mount tire chains on a compact spare tire. If a chain-mounted front tire goes flat, remove one of the full-size rear tires and replace it with the compact spare tire. Remove the flat front tire and replace it with the full-size tire that was removed from the rear. Mount the tire chains on the front tire.

U.S. models only Do not use a puncture-repairing agent on a flat tire, as it can damage the tire pressure sensor.

Continued

383

uuIf a Tire Goes FlatuChanging a Flat Tire

■ Getting Ready to Replace the Flat Tire

Floor Carpet

Handle

Floor Lid

Tool Case

1. Remove the floor mat under the second

row seat.

2 Floor Mats P. 378

2. Pull up the floor carpet. 3. Lift up the floor lid using the handle and

remove it.

4. Take the tool case out of the spare tire well. Take the jack and wheel nut wrench out of the tool case.

5. Unscrew the wing bolt, and remove the spacer cone. Then, remove the spare tire.

Spare Tire

6. Place a wheel block or rock in front and rear

of the wheel diagonal to the flat tire.

The tire to be replaced.

Wheel Blocks

384

7. Place the compact spare tire (wheel side up)

under the vehicle body, near the tire that needs to be replaced.

8. Loosen each wheel nut about one turn

using the wheel nut wrench.

uuIf a Tire Goes FlatuChanging a Flat Tire

Continued

385

uuIf a Tire Goes FlatuChanging a Flat Tire

■ How to Set Up the Jack

1. Place the jack under the jacking point

closest to the tire to be changed.

2. Turn the end bracket (as shown in the

image) clockwise until the top of the jack contacts the jacking point. u Make sure that the jacking point tab is

resting in the jack notch.

3. Raise the vehicle, using the jack handle bar and the jack handle, until the tire is off the ground.

1How to Set Up the Jack

3WARNING

The vehicle can easily roll off the jack, seriously injuring anyone underneath.

Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.

Do not use the jack with people or luggage in the vehicle.

Use the jack provided in your vehicle. Other jacks may not support the weight (“load”) or their shape may not match.

The following instructions must be followed to use the jack safely. • Do not use while the engine is running. • Use only where the ground is firm and level. • Use only at the jacking points. • Do not get in the vehicle while using the jack. • Do not put anything on top of or underneath the

jack.

Jack Handle Bar

Wheel Nut Wrench as Jack Handle

386

uuIf a Tire Goes FlatuChanging a Flat Tire

■ Replacing the Flat Tire

Models with aluminum wheels 1. Remove the wheel nuts and flat tire.

1Replacing the Flat Tire

Do not over tighten the wheel nuts by applying extra torque using your foot or a pipe.

Models with wheel cover 1. Remove the wheel nuts, wheel cover, and

flat tire.

Models with wheel cover Do not attempt to forcibly pry the wheel cover off with a screwdriver or other tool. The wheel cover cannot be removed without first removing the wheel nuts.

Wheel Cover

All models 2. Wipe the mounting surfaces of the wheel

with a clean cloth.

3. Mount the compact spare tire. 4. Screw the wheel nuts until they touch the lips around the mounting holes, and stop rotating.

Continued

387

uuIf a Tire Goes FlatuChanging a Flat Tire

5. Lower the vehicle and remove the jack.

Tighten the wheel nuts in the order indicated in the image. Go around, tightening the nuts, two to three times in this order. Wheel nut torque: 94 lbf∙ft (127 N∙m, 13 kgf∙m)

■ Storing the Flat Tire

Bracket

Storage Bag

The storage bag, bracket, mounting wing bolt (A) and mounting wing bolt (B) are in the tool case.

1Storing the Flat Tire

3WARNING

Loose items can fly around the interior in a crash and can seriously injure the occupants. Store the wheel, jack, and tools securely before driving.

Mounting Wing Bolt (B)

Mounting Wing Bolt (A)

1. Put the flat tire in the storage bag provided

with your vehicle.

388

Plastic Screw

2. Pull down the U-shaped carpet piece, fold

it, and tuck the end under the carpet. 3. Remove the plastic screw with a coin.

Carpet Piece

Mounting Wing Bolt (A)

Bracket

Mounting Wing Bolt (B)

4. Install the bracket and the mounting wing

bolt (A) on the attachment point, and tighten the bolt.

5. Install the flat tire on the bracket with the

inside of the wheel facing toward you.

6. Install the mounting wing bolt (B) to the

bracket through one of the five wheel nut holes, and tighten the bolt. u Poke a hole in the storage bag as

needed.

uuIf a Tire Goes FlatuChanging a Flat Tire

Continued

389

uuIf a Tire Goes FlatuChanging a Flat Tire

■ Storing a flat tire on the folded third row seat

Plastic Screw

1. Turn over the flap on the left side of the

cargo area floor.

2. Pull down the U-shaped carpet piece and

remove the plastic screw with a coin.

Mounting Wing Bolt (B)

3. Place the flat tire face down on the

attachment point.

4. Put the tire mounting wing bolt (B) in the attachment point through one of the five wheel nut holes, and tighten the bolt. u Poke a hole in the storage bag as

needed.

Carpet Piece

390

uuIf a Tire Goes FlatuChanging a Flat Tire

■ TPMS and the Spare Tire Models with information display If you replace a flat tire with the spare tire, the low tire pressure indicator comes on while you are driving. After driving for a few miles (kilometers), the indicator will go off and the TPMS indicator comes on, but this is normal.

If you replace the tire with a specified regular tire, the low tire pressure or TPMS indicator will go off after a few miles (kilometers).

1TPMS and the Spare Tire

The system cannot monitor the pressure of the spare tire. Manually check the spare tire pressure to be sure that it is correct.

Use TPMS specific wheels. Each is equipped with a tire pressure sensor mounted inside the tire behind the valve stem.

Models with multi-information display If you replace a flat tire with the spare tire, the low tire pressure/TPMS indicator comes on while you are driving. After driving for a few miles (kilometers), the indicator will start blinking for a short time and then stay on. CHECK TPMS SYSTEM appears on the multi-information display, but this is normal.

If you replace the tire with a specified regular tire, the warning message on the multi-information display and the TPMS indicator will go off after a few miles (kilometers).

391

Engine Does Not Start

Checking the Engine If the engine does not start, turn the ignition switch to START (e and check the starter.

1Checking the Engine

If you must start the vehicle immediately, use an assisting vehicle to jump start it.

2 Jump Starting P. 393

Starter condition

Starter doesn’t turn or turns over slowly. The battery may be dead. Check each of the items on the right and respond accordingly. The starter turns over normally but the engine doesn’t start. There may be a problem with the fuse. Check each of the items on the right and respond accordingly.

Checklist

Check brightness of the interior light. Turn on interior lights and check brightness. ● If the interior lights are dim or do not come on at all

2 Battery P. 371

● If the interior lights come on normally 2 Fuses P. 403
Review the engine start procedure. Follow its instructions, and try to start the engine again. 2 Starting the Engine P. 291
Check the immobilizer system indicator. When the immobilizer system indicator is blinking, the engine cannot be started.

2 Immobilizer System P. 133

Check the fuel level. There should be enough fuel in the tank. 2 Fuel Gauge P. 86
Check the fuse. Check all fuses, or have the vehicle checked by a dealer.

2 Inspecting and Changing Fuses P. 408

If the problem continues:

2 Emergency Towing P. 409

392

Jump Starting

■ Jump Starting Procedure Turn off the power to electric devices, such as audio and lights. Turn off the engine, then open the hood.

Booster Battery

1. Connect the first jumper cable to your

vehicle's battery + terminal.

2. Connect the other end of the first jumper cable to the assisting vehicle's + terminal. u Use a 12-volt booster battery only.

3. Connect the second jumper cable to the

assisting vehicle's - terminal.

4. Connect the other end of the second

jumper cable to the grounding point as shown. Do not connect this jumper cable to any other part.

5. If your vehicle is connected to another

vehicle, start the assisting vehicle's engine and increase its rpm slightly.

6. Attempt to start your vehicle's engine. If it

turns over slowly, check that the jumper cables have good metal-to-metal contact.

1Jump Starting

3WARNING

A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby.

Keep all sparks, open flames, and smoking materials away from the battery.

Securely attach the jumper cables clips so that they do not come off when the engine vibrates. Also be careful not to tangle the jumper cables or allow the cable ends to touch each other while attaching or detaching the jumper cables.

Battery performance degrades in cold conditions and may prevent the engine from starting.

Continued

393

uuJump Startingu

■ What to Do After the Engine Starts Once your vehicle's engine has started, remove the jumper cables in the following order.

1. Disconnect the jumper cable from your vehicle's ground. 2. Disconnect the other end of the jumper cable from the assisting vehicle's battery

- terminal.

3. Disconnect the jumper cable from your vehicle's battery + terminal. 4. Disconnect the other end of the jumper cable from the assisting vehicle's battery

+ terminal.

Have your vehicle inspected by a nearby service station or a dealer.

394

Shift Lever Does Not Move

Follow the procedure below if you cannot move the shift lever out of the (P position.

■ Releasing the Lock

Cover

Release Button

1. Set the parking brake. 2. Remove the key from the ignition switch. 3. Wrap a cloth around the tip of a small flat-

tip screwdriver. Put it into the shift lock release slot as shown in the image, and remove the cover.

Slot

4. Insert the key into the shift lock release slot. 5. While pushing the key in, press the shift

lever release button and place the shift lever into (N. u The lock is now released. Have the shift

lever checked by a dealer as soon as possible.

Shift Lock Release Slot

395

Overheating

How to Handle Overheating Overheating symptoms are as follows: • The temperature gauge needle is at the

power.

mark or the engine suddenly loses

• Steam or spray comes out of the engine compartment.

■ First thing to do 1. Immediately park the vehicle in a safe place. 2. Turn off all accessories and turn on the hazard warning lights.

u No steam or spray present: Keep the engine running and open the hood. u Steam or spray is present: Turn off the engine and wait until it subsides.

Then open the hood.

1How to Handle Overheating

3WARNING

Steam and spray from an overheated engine can seriously scald you.

Do not open the hood if steam is coming out.

NOTICE Continuing to drive with the temperature gauge needle at the mark may damage the engine.

396

■ Next thing to do

Reserve Tank

uuOverheatinguHow to Handle Overheating

1How to Handle Overheating

3WARNING

Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

If the coolant is leaking, contact a dealer for repairs.

Use water as an emergency/temporary measure only. Have a dealer flush the system with proper antifreeze as soon as possible.

MAX MIN

1. Check that the cooling fan is operating and

stop the engine once the temperature gauge needle comes down. u If the cooling fan is not operating,

immediately stop the engine.

2. Once the engine has cooled down, inspect

the coolant level and check the cooling system components for leaks. u If the coolant level in the reserve tank is

low, add coolant until it reaches the MAX mark.

u If there is no coolant in the reserve tank, check that the radiator is cool. Cover the radiator cap with a heavy cloth and open the cap. If necessary, add coolant up to the base of the filler neck, and put the cap back on.

■ Last thing to do Once the engine has cooled sufficiently, restart it and check the temperature gauge. If the temperature gauge needle has gone down, resume driving. If it has not gone down, contact a dealer for repairs.

397

Indicator, Coming On/Blinking

If the Low Oil Pressure Indicator Comes On

■ Reasons for the indicator to come on Comes on when the engine oil pressure is low. ■ What to do as soon as the indicator comes on 1. Immediately park the vehicle on level ground in a safe place. 2. If necessary, turn the hazard warning lights on. ■ What to do after parking the vehicle 1. Stop the engine and let it sit for about three minutes. 2. Open the hood and check the oil level.

u Add oil as necessary.

2 Oil Check P. 338

3. Start the engine and check the low oil pressure indicator.

u The light goes out: Start driving again. u The light does not go out within 10 seconds: Stop the engine and

contact a dealer for repairs immediately.

1If the Low Oil Pressure Indicator Comes On

NOTICE Running the engine with low oil pressure can cause serious mechanical damage almost immediately.

If the Charging System Indicator Comes On

■ Reasons for the indicator to come on Comes on when the battery is not being charged. ■ What to do when the indicator comes on Turn off the heating and cooling system */climate control system *, rear defogger, and other electrical systems, and immediately contact a dealer for repairs.

1If the Charging System Indicator Comes On

If you need to stop temporarily, do not turn off the engine. Restarting the engine may rapidly discharge the battery.

398

* Not available on all models

uuIndicator, Coming On/BlinkinguIf the Malfunction Indicator Lamp Comes On or Blinks

If the Malfunction Indicator Lamp Comes On or Blinks

■ Reasons for indicator lamp to come on or blink • Comes on when there is a problem with the engine emissions control

system, or the fuel fill cap is missing, or loose.

• Blinks when engine misfiring is detected. ■ What to do when the indicator lamp comes on Avoid high speeds and immediately get your vehicle inspected at a dealer. ■ What to do when the indicator lamp blinks Park the vehicle in a safe place with no flammable items and wait at least 10 minutes or more with the engine stopped until it cools.

1If the Malfunction Indicator Lamp Comes On or Blinks

NOTICE If you drive with the malfunction indicator lamp on, the emissions control system and the engine could be damaged.

If the malfunction indicator lamp blinks again when restarting the engine, drive to the nearest dealer at 31 mph (50 km/h) or less. Have your vehicle inspected.

■ Check/Tighten Fuel Cap Message ■ The message appears on when: An evaporative system leak is detected. This may be caused by the fuel fill cap being loose or not being installed.

■ What to do when the message appears: 1. Stop the engine. 2. Check that the fuel fill cap is fully installed.

u If not, loosen the cap, and then retighten it until it clicks at least once.

3. Drive for several days of normal driving.

u The message should go off.

■ When the malfunction indicator lamp comes on Malfunction indicator lamp comes on if the system continues to detect a leak of gasoline vapor. If this happens, check the fuel fill cap using the procedures described above.

399

uuIndicator, Coming On/BlinkinguIf the Brake System Indicator Comes On

If the Brake System Indicator Comes On

U.S.

Canada

■ Reasons for the indicator to come on • The brake fluid is low. • There is a malfunction in the brake system. ■ What to do when the indicator comes on while driving Press the brake pedal lightly to check pedal pressure. • If normal, check the brake fluid level the next time you stop. • If abnormal, take immediate action. If necessary, downshift the

transmission to slow the vehicle using engine braking.

1If the Brake System Indicator Comes On

Have your vehicle repaired immediately. It is dangerous to drive with low brake fluid. If there is no resistance from the brake pedal, stop immediately in a safe place. If necessary downshift the gears.

If the brake system indicator and ABS indicator come on simultaneously, the electronic brake distribution system is not working. This can result in vehicle instability under sudden braking. Have your vehicle inspected by a dealer immediately.

400

uuIndicator, Coming On/BlinkinguIf the Low Tire Pressure Indicator Comes On

Models with information display If the Low Tire Pressure Indicator Comes On

■ Reasons for the indicator to come on A tire pressure is significantly low. If the compact spare tire is installed, the indicator stays on for a while, then goes off after driving a few miles (kilometers). ■ What to do when the indicator comes on Stop your vehicle in a safe place. Check the tire pressure and adjust the pressure to the specified level. The specified tire pressure is on a label on the driver side doorjamb.

Models with information display If the TPMS Indicator Comes On

■ Reasons for the indicator to come on • Comes on when there is a problem with the TPMS. • If the compact spare is installed, the indicator comes on after driving

for a few miles (kilometers).

■ What to do when the indicator comes on Have the tire inspected by a dealer as soon as possible. If the compact spare tire causes the indicator to comes on, change the tire to a full-size tire. The indicator goes off after driving for a few miles (kilometers).

1If the Low Tire Pressure Indicator Comes On

NOTICE Driving on an extremely underinflated tire can cause it to overheat. An overheated tire can fail. Always inflate your tires to the prescribed level.

401

uuIndicator, Coming On/BlinkinguIf the Low Tire Pressure/TPMS Indicator Comes On or Blinks

Models with multi-information display If the Low Tire Pressure/TPMS Indicator Comes On or Blinks

■ Reasons for the indicator to come on or blink A tire pressure is significantly low. If there is a problem with the TPMS or the compact spare tire is installed, the indicator blinks for about one minute, and then stays on. ■ What to do when the indicator comes on Stop your vehicle in a safe place. Check the tire pressure and adjust the pressure to the specified level. The specified tire pressure is on a label on the driver side doorjamb. ■ What to do when the indicator blinks Have the tire inspected by a dealer as soon as possible. If the compact spare tire causes the indicator to blink, change the tire to a full- size tire. The indicator goes off after driving for a few miles (kilometers).

1If the Low Tire Pressure/TPMS Indicator Comes On or Blinks

NOTICE Driving on an extremely underinflated tire can cause it to overheat. An overheated tire can fail. Always inflate your tires to the prescribed level.

402

Fuses

Fuse Locations If any electrical devices are not working, turn the ignition switch to LOCK (0 and check to see if any applicable fuse is blown.

Fuse locations are shown on the fuse box cover. Locate the fuse in question by the fuse number and box cover number.

■ Engine Compartment Fuse Box

(Primary)

Located on the passenger’s side, near the windshield washer reservoir. Push the tabs to open the box.

■ Circuit protected and fuse rating

Circuit Protected

Amps

−

−

−

− −

− −

Ignition Coil

15 A 15 A 7.5 A 7.5 A

15 A 15 A 15 A 15 A

FI Sub DBW FI Main

ACG FR Washer VB SOL ECU FR

10
11
12
13
14
15
16
17
18
19
20 Right Headlight High Beam 10 A 21
22
23
24
25

Radio Back Up MG Clutch

Left Headlight High Beam

Front Fog Lights *

20 A 10 A 7.5 A 20 A

Small Lights

FI ECU

7.5 A

10 A

10 A

−

−

−

−

−

−

−

−

−

−

−

Circuit Protected

Left Headlight Low Beam

Amps 26 Right Headlight Low Beam 15 A 15 A 27
28
7.5 A 30 A 29
30 A 30
31
30 A

IGPS Oil Level Cooling Fan

Wiper Main

Sub Fan

* Not available on all models

Continued

403

Circuit Protected

Stop & Horn

Hazard

Interior Lights

10
11

Amps 20 A 15 A 7.5 A

uuFusesuFuse Locations

■ Engine Compartment Fuse Box

(Secondary)

Located near the battery. Push the tabs to open the box.

404

* Not available on all models

■ Circuit protected and fuse rating

Circuit Protected

Battery Fan Main

2-1
2-2 Passenger’s Side Fuse Box 2
2-3
2-4
2-5
2-6
2-7

Stop & Horn, Hazard

Rear Blower

VSA Motor

VSA FSR

FI Main

2-8

Battery Management

System Main

IG1 Main

Driver’s Side Fuse Box 2

3-1
3-2
3-3
3-4 Passenger’s Side Fuse Box 1
3-5

Driver’s Side Fuse Box 1
Primary Under-hood Fuse

Rear Fuse Box 1

3-6

3-7

3-8

Box Main

Front Blower

Passenger’s Side Power

Slide Door Motor *

− −

Rear Window Defogger

−

Battery Management

System

Amps 125 A 60 A 50 A 30 A 30 A 40 A 30 A 30 A