2010 Honda Odyssey Owners Manual

pressing the INFO button repeatedly if the system message indicator remains lit on the instrument panel.

FastenSeatBelt

Multi-Information Display

FASTEN SEAT BELT FASTEN PASSENGER SEAT BELT RELEASE PARKING BRAKE WARNING: APPROACHING OBJECT

In addition to the seat belt reminder indicator in the instrument panel, you will also see a ‘‘FASTEN SEAT BELT’’ or ‘‘FASTEN PASSENGER SEAT BELT’’ message. This remains displayed if you ignore it and do not fasten the seat belt while driving.

CONTINUED

91

2010 Odyssey０９／０４／１０　１６：１２：０５　３１ＳＨＪ６５０　００９７　

Multi-Information Display

DoorandTailgateOpen

ReleaseParkingBrake

RemoveKey

U.S.

Canada

If the tailgate or any door(s) is not closed tightly, the display reminds you to close the tailgate or the door(s) before you start driving. This display continues until you close the door(s) or the tailgate. Pressing the INFO button on the steering wheel momentarily changes the display to the normal display, but it will come back after 5 seconds.

If you start driving without releasing the parking brake, the multi- information display interrupts the current display and shows ‘‘RELEASE PARKING BRAKE.’’ This message continues, and a chime sounds, until you release the parking brake, or the vehicle speed slows down to less than 0.5 mph (0.8
km/h).

If you leave the key in the ignition switch in the LOCK (0) or ACCESSORY (I) position and open the driver’s door, you will see ‘‘REMOVE KEY’’ on the display and hear a reminder beeper.

92

2010 Odyssey０９／０４／１０　１６：１２：１１　３１ＳＨＪ６５０　００９８　

Multi-Information Display

TightenFuelCap

replace the fuel fill cap. To scroll to another message, press the INFO button. The ‘‘TIGHTEN FUEL CAP’’ message will appear each time you restart the engine until the system turns the message off.

Your vehicle’s on board diagnostic system will detect a loose or missing fuel fill cap as an evaporative system leak. The first time a leak is detected a ‘‘TIGHTEN FUEL CAP’’ message appears on the multi-information display. Turn the engine off, and confirm the fuel fill cap is installed. If it is, loosen it, then retighten it until it clicks at least once. The message should go off after several days of normal driving once you tighten or

If the system still detects a leak in your vehicle’s evaporative emissions system, the malfunction indicator lamp (MIL) comes on. If the fuel fill cap was not already tightened, turn the engine off, and check or retighten the fuel fill cap until it clicks at least once. The MIL should go off after several days of normal driving once the cap is tightened or replaced. If the MIL does not go off, have your vehicle inspected by a dealer. For more information, see page

478

CONTINUED

93

2010 Odyssey０９／０４／１０　１６：１２：１８　３１ＳＨＪ６５０　００９９　

Multi-Information Display

BrakeFluidLow

FuelLow

WasherFluidLow

U.S.

Canada

If the brake fluid level is at or below the MIN mark on the side of the brake fluid reservoir in the engine compartment, you will see ‘‘BRAKE FLUID LOW.’’ If you see this message, have the brake system checked by your dealer (see page 479

).

If the level of the fuel in the tank gets low, you will see ‘‘FUEL LOW’’ on the multi-information display, and you must refuel soon. The low fuel indicator on the instrument panel will also come on.

OnCanadianTouringmodelonly If the fluid level in the windshield washer reservoir gets low, you will see ‘‘WASHER FLUID LOW’’ on the multi-information display.

94

2010 Odyssey０９／０４／１０　１６：１２：２８　３１ＳＨＪ６５０　０１００　

PassengerSideAirbagOff

CheckTirePressure

Warning:ApproachingObject

Multi-Information Display

U.S.

Canada

If the passenger’s side airbag has automatically shut off, you will see ‘‘PASSENGER SIDE AIRBAG OFF’’ on the multi-information display. See page

for more information.

35

If one or more of your vehicle tires are low on pressure, you will see a ‘‘CHECK TIRE PRESSURE’’ message on the display. See page for more information on the tire 399
pressure monitoring system (TPMS).

This message, and the indicator to the left of the message, is part of the parking sensor system. If you are approaching too close to an object, you will see ‘‘WARNING: APPROACHING OBJECT’’ on the display and hear a beeper. See page 362

for more information.

CONTINUED

95

2010 Odyssey０９／０４／１０　１６：１２：３８　３１ＳＨＪ６５０　０１０１　

Multi-Information Display

MaintenanceMessages

When the engine oil life reaches 15%, the display shows ‘‘SERVICE DUE SOON’’ and the code for the maintenance items to be performed.

When the engine oil life reaches 5%, the display shows ‘‘SERVICE DUE NOW’’ along with the same maintenance items.

96

Have your dealer do the indicated maintenance as soon as you see this message, and have them reset the display after completing the service.

If you do not perform the indicated maintenance or do not reset the display, the message changes to ‘‘SERVICE PAST DUE’’ when the engine oil life becomes 0%.

These messages appear on the multi- information display each time you turn the ignition switch to the ON (II) position.

For details on engine oil life and maintenance messages, refer to page 417

Also refer to page maintenance safety precautions.

for important

414

CheckTPMSSystem

If there is a problem in the tire pressure monitoring system (TPMS), you will see ‘‘CHECK TPMS SYSTEM’’ on the multi-information display. If you see this message, the TPMS is not monitoring tire pressures. Have the TPMS checked by your dealer as soon as possible (see page

402

).

2010 Odyssey０９／０４／１０　１６：１２：４６　３１ＳＨＪ６５０　０１０２　

CheckVSASystem

CheckEngineOilLevel

CheckChargingSystem

Multi-Information Display

If there is a problem with the vehicle stability assist (VSA) system, you will see ‘‘CHECK VSA SYSTEM’’ on the multi-information display. If you see this message, have the VSA system checked by your dealer (see page

394

).

If the engine oil is very low or has lost pressure, you will see ‘‘CHECK ENGINE OIL LEVEL’’ on the multi- information display. You will also see the low oil pressure indicator in the instrument panel flashing or staying on. If you see this message, you should take immediate action since serious engine damage is possible. Follow the procedure on page 477

If you see ‘‘CHECK CHARGING SYSTEM’’ on the multi-information display, it means the battery is not being charged. See page more information.

477

for

CONTINUED

97

2010 Odyssey０９／０４／１０　１６：１２：５５　３１ＳＨＪ６５０　０１０３　

Multi-Information Display

CheckEmissionSystem

CheckBrakeSystem

CheckTransmission

U.S.

Canada

If you see ‘‘CHECK EMISSION SYSTEM’’ on the multi-information display, it means one of the engine’s emission systems may have a problem. Have your vehicle checked by your dealer (see page

478

).

If there is a problem with the brake system, you will see ‘‘CHECK BRAKE SYSTEM’’ on the multi- information display. The parking brake and brake system indicator in the instrument panel will also come on. See page information.

for more

479

If there is a problem with the automatic transmission, you will see ‘‘CHECK TRANSMISSION’’ on the multi-information display. Avoid rapid acceleration, and have the transmission checked by a dealer as soon as possible.

98

2010 Odyssey０９／０４／１０　１６：１３：０４　３１ＳＨＪ６５０　０１０４　

CheckABSSystem

CheckAirbagSystem

CheckParkingSensorSystem

Multi-Information Display

If there is a problem in the anti-lock brake system (ABS), you will see ‘‘CHECK ABS SYSTEM’’ on the multi-information display. If you see this message, have your vehicle checked by a dealer (see page

392

).

If there is a problem with your front airbags, side airbags, passenger’s side airbag automatic cutoff system, automatic seat belt tensioners, side curtain airbags, driver’s seat position sensor, or the front passenger’s weight sensors, you will see ‘‘CHECK AIRBAG SYSTEM’’ on the multi-information display. Take your vehicle to a dealer as soon as possible (see page

34

).

If there is a problem with the parking sensor system, the multi- information display shows a ‘‘CHECK PARKING SENSOR SYSTEM’’ message. See page 363

for more information.

CONTINUED

99

2010 Odyssey０９／０４／１０　１６：１３：１２　３１ＳＨＪ６５０　０１０５　

Multi-Information Display

CheckLeft/RightSlidingDoor

CheckPowerTailgate

CheckDRLSystem

U.S.

U.S.

Canada

Canada

If there is a problem with either power sliding door, the multi- information display shows ‘‘CHECK LEFT SLIDING DOOR’’ or ‘‘CHECK RIGHT SLIDING DOOR.’’ See page 166

for more information.

If there is a problem with the power tailgate, the display shows ‘‘CHECK POWER TAILGATE.’’ See page 158

for more information.

If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi- information display, there is a problem in the high beam headlight’s circuit. Take your vehicle to a dealer to have it checked.

100

2010 Odyssey０９／０４／１０　１６：１３：２４　３１ＳＨＪ６５０　０１０６　

Customized Settings With the ignition switch in the ON (II) position, press and hold the INFO button for more than 3
seconds. ‘‘CUSTOMIZE ENTRY’’ appears on the multi-information display.

You can customize some vehicle control settings for ‘‘DRIVER 1’’ and ‘‘DRIVER 2’’ separately.

To have the driver’s ID detected, make sure you use your transmitter to unlock the driver’s door.

If you use the key to unlock the driver’s door, the system cannot recognize either ‘‘DRIVER 1’’ or ‘‘DRIVER 2.’’ In this case, when you try to enter the customizing mode, ‘‘DRIVER UNKNOWN CUSTOMIZE IMPOSSIBLE’’ will be displayed, and you cannot customize the settings.

You cannot customize the settings under these conditions:

If you turn the ignition switch to the ACCESSORY (I) or the LOCK (0) position.

If you move the shift lever out of Park.

You can cancel each custom setting (Driver 1, Driver 2). Press and hold the LOCK and SLIDING DOOR button (passenger’s side) at the same time until the LED in the remote transmitter blinks twice. At this time, the custom setting is changed to the default setting. To activate each custom setting (Driver 1, Driver 2), repeat this procedure. The LED will blink for 1 second to indicate the custom setting has been activated.

Multi-Information Display

The first customizing menu is:

CHANGE SETTING DEFAULT ALL

If you want to change any vehicle control settings, select ‘‘CHANGE SETTING,’’ and follow the instructions on page

106

If you want the settings as they were when the vehicle left the factory, select ‘‘DEFAULT ALL,’’ as described on page

104

Use the INFO button on the steering wheel to see the settings, and the SEL/RESET button to enter your selections.

Refer to the table on the following pages about the settings you want to customize.

CONTINUED

101

2010 Odyssey０９／０４／１０　１６：１３：３０　３１ＳＨＪ６５０　０１０７　

Multi-Information Display

Group Setup METER SETUP (P. 107)

Menu Item

LANGUAGE SELECTION

Changes the language used in the display.

Description

Setting Option

ADJUST OUTSIDE TEMP. DISPLAY

Changes the outside temperature reading above or below its current reading.

TRIP A RESET WITH REFUEL ELAPSED TIME RESET

MEMORY POSITION LINK INTERIOR LIGHT DIMMING TIME

Causes trip meter A and the average fuel economy to reset when you refuel. Resets the elapsed time of your current trip.

Changes the driver’s seat to a stored setting.

Changes how long (in seconds) the interior lights stay on after you close the doors.

HEADLIGHT AUTO OFF TIMER

Changes how long (in seconds) the exterior lights stay on after you close the driver’s door.

POSITION SETUP (P. 116) LIGHTING SETUP (P. 118)

＊

Default setting

102

Page 108

110

112

114

116

118

120

〜 ＊ 〜 ＊

5°F (U.S.) 3°C

＊

＊

＊

5°F 3°C

0°F 0°C

ENGLISH FRENCH SPANISH − 〜± − 〜± (Canada) ON OFF IGN RESET TRIP A RESET TRIP B RESET ON OFF 15 sec 30 sec 60 sec 0 sec 15 sec 30 sec 60 sec

＊

＊

＊

2010 Odyssey０９／０４／１０　１６：１３：３５　３１ＳＨＪ６５０　０１０８　

Multi-Information Display

Group Setup

DOOR · WINDOW SETUP (P. 122)

Menu Item

Description

AUTO DOOR LOCK

Changes when the doors automatically lock.

AUTO DOOR UNLOCK

Changes when the doors automatically unlock.

KEYLESS LOCK ACKNOWLEDGEMENT

SECURITY RELOCK TIMER

FRONT WIPER ACTION

The exterior lights flash each time you press the LOCK or UNLOCK button. A beeper will also sound when you press the LOCK button twice. Changes how long it takes (in seconds) for the doors to relock and the security system to set after you unlock and do not open the door. Changes the wiper operation between two settings when the wiper switch is in the INT position. Changes all the customized settings as they were when the vehicle left the factory.

WIPER SETUP (P. 131) DEFAULT ALL

＊

Default setting

Setting Option

＊

＊

SHIFT FROM P WITH VEHICLE SPEED OFF DRIVER’S DOOR WITH SHIFT TO P ALL DOORS WITH SHIFT TO P DRIVER’S DOOR WITH IGN OFF ALL DOORS WITH IGN OFF OFF ON OFF

＊

＊

30 sec 60 sec 90 sec WITH VEH SPD INTERMITTENT OK CANCEL

＊

Page 123

125

127

129

131

104

103

2010 Odyssey０９／０４／１０　１６：１３：４１　３１ＳＨＪ６５０　０１０９　

Multi-Information Display

DEFAULT ALL

To set the default settings, select ‘‘OK’’ by pressing the INFO button, then press the SEL/RESET button.

When ‘‘DEFAULT ALL’’ is completed successfully, you will see the above display for several seconds, and the display will return to ‘‘CUSTOMIZE ENTRY.’’

To enter the customizing mode, press and hold the INFO button for more than 3 seconds. Then select ‘‘DEFAULT ALL’’ by pressing the INFO button.

Press the SEL/RESET button to enter ‘‘DEFAULT ALL.’’

104

2010 Odyssey０９／０４／１０　１６：１３：４６　３１ＳＨＪ６５０　０１１０　

Multi-Information Display

If ‘‘DEFAULT ALL’’ is not completed successfully, you will see the above display for several seconds, then the display goes back to the normal message mode. Repeat the procedure to select ‘‘DEFAULT ALL.’’

If you want to cancel ‘‘DEFAULT ALL,’’ select ‘‘CANCEL,’’ then press the SEL/RESET button. The display goes back to ‘‘CUSTOMIZE ENTRY.’’

105

2010 Odyssey０９／０４／１０　１６：１３：５６　３１ＳＨＪ６５０　０１１１　

Multi-Information Display

Change Setting You can customize some of the vehicle control settings to your preference. Here are the settings you can customize:

METER SETUP (see page 107
POSITION SETUP (see page 116
LIGHTING SETUP (see page 118
DOOR · WINDOW SETUP (see page WIPER SETUP (see page

122

131

While the multi-information display is showing ‘‘CHANGE SETTING,’’ press the SEL/RESET button. The display will change to the initial display of CUSTOMIZE GROUP. Then, each time you press the INFO button, the display changes as shown in the next column. Press the INFO button until you see the setup you want to customize, and press the SEL/RESET button to enter your selection.

106

Press the SEL/RESET button

Press the INFO button

2010 Odyssey０９／０４／１０　１６：１４：０５　３１ＳＨＪ６５０　０１１２　

Meter Setup There are four custom settings items in the Meter Setup:

Press the INFO button

Multi-Information Display

108

LANGUAGE SELECTION (see page ADJUST OUTSIDE TEMP. DISPLAY (see page TRIP A RESET WITH REFUEL (see page ELAPSED TIME RESET (see page

110

112

114

While ‘‘METER SETUP’’ is displayed, press the SEL/RESET button on the steering wheel. Then, press the INFO button repeatedly. Each time you press the INFO button, the display changes as shown. To customize a setting, press the INFO button repeatedly until you see the setting, and press the SEL/ RESET button. Then, follow the procedures described on the following pages.

CONTINUED

107

2010 Odyssey０９／０４／１０　１６：１４：１１　３１ＳＨＪ６５０　０１１３　

Multi-Information Display

LanguageSelection

While the multi-information display is showing ‘‘METER SETUP,’’ press the SEL/RESET button on the steering wheel. The display changes to ‘‘LANGUAGE SELECTION.’’ Press the SEL/RESET button again to enter the language selection mode.

There are three selectable languages, English, French, and Spanish. Each time you press the INFO button, the display changes as shown.

Select the language you want by pressing the INFO button, and press the SEL/RESET button to enter your selection.

108

2010 Odyssey０９／０４／１０　１６：１４：１８　３１ＳＨＪ６５０　０１１４　

Multi-Information Display

When language selection is successfully completed, the display changes to the screen shown above for several seconds, then goes back to ‘‘CUSTOMIZE MENU.’’

If you fail to select a language properly, you will see the above display for several seconds, then the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.

To exit ‘‘LANGUAGE SELECTION,’’ press the INFO button repeatedly until you see ‘‘EXIT,’’ then press the SEL/RESET button. The display goes back to ‘‘CUSTOMIZE MENU.’’

All messages on the multi- information display will be shown in the language you selected.

CONTINUED

109

2010 Odyssey０９／０４／１０　１６：１４：２３　３１ＳＨＪ６５０　０１１５　

Multi-Information Display

AdjustOutsideTemp.Display If you find that the temperature reading is always a few degrees below or above the actual temperature, adjust it as described in the following section.

While the multi-information display shows ‘‘METER SETUP,’’ press the SEL/RESET button on the steering wheel. The display changes to the ‘‘CUSTOMIZE MENU.’’ Press the INFO button once, and you will see ‘‘ADJ. OUTSIDE TEMP. DISPLAY’’ as shown above.

Press the SEL/RESET button. The display changes as shown above. The highlighted number is the current adjustment above or below the outside temperature. Press the INFO button repeatedly until the appropriate number appears, then press the SEL/RESET button to enter your selection.

110

2010 Odyssey０９／０４／１０　１６：１４：２９　３１ＳＨＪ６５０　０１１６　

Multi-Information Display

When your selection is successfully entered, you will see the above display for several seconds, and then the display changes back to ‘‘CUSTOMIZE MENU.’’

If you fail to enter the desired adjustment properly, you will see the above display for several seconds, then the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the adjustment.

To exit ‘‘ADJ. OUTSIDE TEMP. DISPLAY,’’ press the INFO button until you see ‘‘EXIT,’’ and press the SEL/RESET button. The display goes back to ‘‘CUSTOMIZE MENU.’’

CONTINUED

111

2010 Odyssey０９／０４／１０　１６：１４：３５　３１ＳＨＪ６５０　０１１７　

Multi-Information Display

TripAResetwithRefuel To cause ‘‘Trip meter A’’ and ‘‘Average Fuel Economy’’ to reset every time you refuel your vehicle, adjust it as described on the following pages.

While the multi-information display shows ‘‘METER SETUP’’ of the ‘‘CUSTOMIZE GROUP,’’ press the SEL/RESET button on the steering wheel. The display changes to ‘‘CUSTOMIZE MENU.’’ Press the INFO button repeatedly until you see ‘‘TRIP A RESET WITH REFUEL.’’ in the lower segment as shown above.

Press the SEL/RESET button. The display changes as shown above. The lower segment changes between ‘‘ON’’ and ‘‘OFF’’ each time you press the INFO button. Enter your selection by pressing the SEL/ RESET button.

112

2010 Odyssey０９／０４／１０　１６：１４：４１　３１ＳＨＪ６５０　０１１８　

Multi-Information Display

When your selection is successfully entered, you will see the above display for several seconds, and then the display goes back to ‘‘CUSTOMIZE MENU.’’

If you fail to enter your selection, you will see the above display for several seconds, then the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.

To exit ‘‘TRIP A RESET WITH REFUEL,’’ press the INFO button until you see ‘‘EXIT,’’ and press the SEL/RESET button. The display goes back to ‘‘CUSTOMIZE MENU.’’

CONTINUED

113

2010 Odyssey０９／０４／１０　１６：１４：４８　３１ＳＨＪ６５０　０１１９　

Multi-Information Display

ElapsedTimeReset There are three possible settings:

IGN RESET: The elapsed time resets each time the ignition switch is turned to the ON (II) position.

TRIP A RESET: The elapsed time resets each time the TRIP A is reset.

TRIP B RESET: The elapsed time resets each time the TRIP B is reset.

While the multi-information display shows ‘‘METER SETUP’’ of the ‘‘CUSTOMIZE GROUP,’’ press the SEL/RESET button on the steering wheel. The display changes to ‘‘CUSTOMIZE MENU.’’ Press the INFO button repeatedly until you see ‘‘ELAPSED TIME RESET’’ in the lower segment as shown above.

Press the SEL/RESET button. The display changes as shown above.

Press the INFO button repeatedly until the desired condition appears, then press the SEL/RESET button to enter your selection.

114

2010 Odyssey０９／０４／１０　１６：１４：５４　３１ＳＨＪ６５０　０１２０　

Multi-Information Display

When your selection is entered, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’

If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.

To exit ‘‘ELAPSED TIME RESET,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.

115

2010 Odyssey０９／０４／１０　１６：１５：０２　３１ＳＨＪ６５０　０１２１　

Multi-Information Display

Position Setup If ‘‘MEMORY POSITION LINK’’ is ‘‘ON,’’ the driver’s seat and outside mirrors move to the positions stored in the memory when you open the driver’s door, using the remote transmitter.

MemoryPositionSetup

184

Refer to page for setting the seat position memory. Also refer to page 149

for remote transmitter use.

While the multi-information display shows ‘‘POSITION SETUP,’’ press the SEL/RESET button on the steering wheel. The display changes to ‘‘MEMORY POSITION LINK’’ as shown above.

Press the SEL/RESET button. The display changes as shown above.

Select ‘‘ON’’ or ‘‘OFF’’ by pressing the INFO button, and enter your selection by pressing the SEL/ RESET button.

116

2010 Odyssey０９／０４／１０　１６：１５：０７　３１ＳＨＪ６５０　０１２２　

Multi-Information Display

When your selection is entered, you will see the above display for several seconds, then the display goes back to ‘‘CUSTOMIZE MENU.’’

If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.

To exit ‘‘MEMORY POSITION LINK,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/ RESET button.

117

2010 Odyssey０９／０４／１０　１６：１５：１６　３１ＳＨＪ６５０　０１２３　

Multi-Information Display

Lighting Setup There are two custom settings in the Lighting Setup:

InteriorLightDimmingTime

INTERIOR LIGHT DIMMING TIME (see next column) HEADLIGHT AUTO OFF TIMER (see page

120

While the ‘‘LIGHTING SETUP’’ is displayed, press the SEL/RESET button on the steering wheel. Each time you press the INFO button, the display changes between ‘‘INTERIOR LIGHT DIMMING TIME’’ and ‘‘HEADLIGHT AUTO OFF TIMER.’’ To make your selection, press the SEL/RESET button.

118

The interior lights fade out when you close all doors. You can change the time that the interior lights fade out.

While the multi-information display shows ‘‘LIGHTING SETUP,’’ press the SEL/RESET button on the steering wheel. The display changes to ‘‘INTERIOR LIGHT DIMMING TIME’’ as shown above.

Press the SEL/RESET button. The display changes as shown above.

Each time you press the INFO button, the highlighted number changes from ‘‘15 sec,’’ to ‘‘30 sec,’’ and then to ‘‘60 sec.’’ To make your selection, press the SEL/RESET button.

2010 Odyssey０９／０４／１０　１６：１５：２２　３１ＳＨＪ６５０　０１２４　

Multi-Information Display

When your selection is entered, you will see the above display for several seconds, and then the display goes back to ‘‘CUSTOMIZE MENU.’’

If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.

To exit ‘‘INTERIOR LIGHT DIMMING TIME,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.

119

2010 Odyssey０９／０４／１０　１６：１５：２８　３１ＳＨＪ６５０　０１２５　

Multi-Information Display

HeadlightAutoOffTimer The headlights, parking lights, taillights, and license plate light turn off after the selected time when you remove the key from the ignition switch and close the driver’s door.

While the multi-information display shows ‘‘LIGHTING SETUP,’’ press the SEL/RESET button on the steering wheel. Then press the INFO button to display ‘‘HEADLIGHT AUTO OFF TIMER’’ as shown above.

Press the SEL/RESET button. The display changes as shown above.

Each time you press the INFO button, the highlighted number changes from ‘‘0 sec,’’ to ‘‘15 sec,’’ to ‘‘30 sec,’’ and then to ‘‘60 sec.’’ Press the INFO button repeatedly until the desired time appears, then press the SEL/RESET button to enter your selection.

120

2010 Odyssey０９／０４／１０　１６：１５：３４　３１ＳＨＪ６５０　０１２６　

Multi-Information Display

When your selection is entered, you will see the above display for several seconds, and then the display goes back to ‘‘CUSTOMIZE MENU.’’

If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.

To exit ‘‘HEADLIGHT AUTO OFF TIMER,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.

121

2010 Odyssey０９／０４／１０　１６：１５：４３　３１ＳＨＪ６５０　０１２７　

Multi-Information Display

Door · Window Setup There are three custom settings in the Door · Window Setup:

125

AUTO DOOR LOCK (see page 123
AUTO DOOR UNLOCK (see page KEYLESS LOCK ACKNOWLEDGEMENT (see page SECURITY RELOCK TIMER (see page

127

129

While the multi-information display shows ‘‘DOOR · WINDOW SETUP,’’ press the SEL/RESET button on the steering wheel. Each time you press the INFO button, the display changes as shown in the next column. To customize a setting, press the INFO button repeatedly until you see the setting you want to customize, and press the SEL/RESET button. Then follow the procedures described on the following pages.

122

Press the INFO button

2010 Odyssey０９／０４／１０　１６：１５：５１　３１ＳＨＪ６５０　０１２８　

Multi-Information Display

AutoDoorLock There are three settings you can choose from:

−

OFF The auto door lock mode is deactivated all the time.

VEHICLE SPEED The doors lock when the vehicle speed reaches 9
mph (15 km/h).

−

SHIFT FROM P The doors lock whenever you move the shift lever out of Park.

−

While the multi-information display shows ‘‘DOOR · WINDOW SETUP’’ press the SEL/RESET button on the steering wheel. The display changes to ‘‘AUTO DOOR LOCK’’ as shown above.

Press the SEL/RESET button. The display changes as shown above.

Press the INFO button repeatedly until the desired condition appears, then press the SEL/RESET button to enter your selection.

CONTINUED

123

2010 Odyssey０９／０４／１０　１６：１５：５７　３１ＳＨＪ６５０　０１２９　

Multi-Information Display

When your selection is entered, you will see the above display for several seconds, and then the display goes back to ‘‘CUSTOMIZE MENU.’’

If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.

To exit ‘‘AUTO DOOR LOCK,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.

124

2010 Odyssey０９／０４／１０　１６：１６：０５　３１ＳＨＪ６５０　０１３０　

Multi-Information Display

AutoDoorUnlock There are three settings you can choose from:

−

SHIFT TO P The driver’s door or all the doors unlock when you move the shift lever to Park.

−

IGN OFF The driver’s door or all the doors unlock when you turn the ignition switch to the LOCK (0) position.

−

OFF is deactivated all the time.

The auto door unlock mode

While the multi-information display shows ‘‘DOOR·WINDOW SETUP,’’ press the SEL/RESET button on the steering wheel. Then press the INFO button once. The display changes to ‘‘AUTO DOOR UNLOCK’’ as shown above.

Press the SEL/RESET button. The display changes as shown above.

Press the INFO button repeatedly until the desired condition appears, and press the SEL/RESET button to enter your selection.

CONTINUED

125

2010 Odyssey０９／０４／１０　１６：１６：１１　３１ＳＨＪ６５０　０１３１　

Multi-Information Display

When your selection is entered, you will see the above display for several seconds, and then the display goes back to ‘‘CUSTOMIZE MENU.’’

If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.

To exit ‘‘AUTO DOOR UNLOCK,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.

126

2010 Odyssey０９／０４／１０　１６：１６：１９　３１ＳＨＪ６５０　０１３２　

Multi-Information Display

KeylessLockAcknowledgement When you press the UNLOCK button on the remote transmitter to unlock the doors and the tailgate, the exterior lights blink twice to verify that the doors and the tailgate are unlocked and the security system is turned off.

When you push the LOCK button on the remote transmitter, some exterior lights flash, and a beeper sounds when you push the LOCK button again within 5 seconds to verify that the doors and the tailgate are locked and the security system has set (see page customize the exterior lights not to flash and the beeper not to sound.

). You can

318

While the multi-information display shows ‘‘DOOR·WINDOW SETUP,’’ press the SEL/RESET button on the steering wheel. Then press the INFO button repeatedly until you see ‘‘KEYLESS LOCK ACKNOWLEDGEMENT’’ as shown above.

Press the SEL/RESET button. The display changes as shown above.

Each time you press the INFO button, the display changes to ‘‘ON,’’ to ‘‘OFF,’’ then to ‘‘EXIT.’’

Select ‘‘ON’’ or ‘‘OFF’’ by pressing the INFO button, and enter your selection by pressing the SEL/ RESET button.

CONTINUED

127

2010 Odyssey０９／０４／１０　１６：１６：２５　３１ＳＨＪ６５０　０１３３　

Multi-Information Display

When your selection is entered, you will see the above display for several seconds, and then the display changes to ‘‘CUSTOMIZE MENU.’’

If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.

To exit ‘‘KEYLESS LOCK ACKNOWLEDGEMENT,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.

128

2010 Odyssey０９／０４／１０　１６：１６：３２　３１ＳＨＪ６５０　０１３４　

Multi-Information Display

SecurityRelockTimer If you unlock the doors and the tailgate with the remote transmitter, but do not open any of the doors or the tailgate within 30 seconds, the doors and the tailgate automatically relock and the security system sets.

You can change this relock time from 30 seconds to 60 or 90 seconds.

While the multi-information display shows ‘‘DOOR·WINDOW SETUP,’’ press the SEL/RESET button on the steering wheel. Then press the INFO button repeatedly until you see ‘‘SECURITY RELOCK TIMER’’ as shown above.

Press the SEL/RESET button, then press the INFO button.

Select the desired relock time by pressing the INFO button, and enter your selection by pressing the SEL/ RESET button.

CONTINUED

129

2010 Odyssey０９／０４／１０　１６：１６：３８　３１ＳＨＪ６５０　０１３５　

Multi-Information Display

When your selection is entered, you will see the above display for several seconds, and then the display goes back to ‘‘CUSTOMIZE MENU.’’

If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.

To exit ‘‘SECURITY RELOCK TIMER,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.

130

2010 Odyssey０９／０４／１０　１６：１６：４７　３１ＳＨＪ６５０　０１３６　

FrontWiperAction

Wiper Setup You can select from these two settings when the wiper switch is in the INT (intermittent) position:

WITH VEH SPD The intermittent operation varies according to vehicle speed.

−

Multi-Information Display

−

The

INTERMITTENT intermittent operation varies according to the selection you make on the wiper lever’s intermittent control ring.

With ‘‘WIPER SETUP’’ shown on the multi-information display, press the SEL/RESET button on the steering wheel. The display changes to ‘‘FRONT WIPER ACTION’’ as shown above.

Press the SEL/RESET button. The display changes as shown above.

Press the INFO button to select ‘‘WITH VEH SPD’’ or ‘‘INTERMITTENT,’’ and enter your selection by pressing the SEL/ RESET button.

CONTINUED

131

2010 Odyssey０９／０４／１０　１６：１６：５３　３１ＳＨＪ６５０　０１３７　

Multi-Information Display

When your selection is entered, you will see the above display for several seconds, and then the display goes back to ‘‘CUSTOMIZE MENU.’’

If you fail to enter your selection, you will see the above display for several seconds, and the display goes back to ‘‘CUSTOMIZE MENU.’’ Repeat the setup.

To exit ‘‘FRONT WIPER ACTION,’’ press the INFO button until you see ‘‘EXIT,’’ then press the SEL/RESET button.

132

2010 Odyssey０９／０５／０７　１０：４４：２０　３１ＳＨＪ６５０　０１３８　

PEDAL POSITION ADJUSTMENT SWITCH ＊ (P.193)

HEADLIGHTS/TURN SIGNAL/ FOG LIGHTS

(P.135, 138)

＊

POWER SLIDING DOOR SWITCH ＊

(P.162)

MOONROOF SWITCH ＊ (P.189)

＊

REMOTE AUDIO CONTROL BUTTONS (P.282) POWER TAILGATE (P.158)/ SWITCH ＊ VEHICLE STABILITY ASSIST (VSA) OFF SWITCH

(P.395)

PARKING SENSOR SYSTEM SWITCH ＊ (P.361) VEHICLE STABILITY ASSIST (VSA) OFF SWITCH (P.395)

NAVIGATION SYSTEM BUTTONS ＊

HORN ＊

BLUETOOTH HANDSFREELINK BUTTONS

(P.327)

＊

STEERING WHEEL ADJUSTMENT (P.141)

Controls Near the Steering Wheel

WINDSHIELD WIPERS/WASHERS REAR WINDOW WIPER/WASHER

(P.134) (P.135)

CRUISE CONTROL BUTTONS (P.319)

＊

CLOCK (P.281)

PASSENGER AIRBAG OFF INDICATOR (P.35)

HAZARD WARNING BUTTON (P.140)

AUDIO SYSTEM/ REAR ENTERTAINMENT SYSTEM ＊ (P.221, 285)

REAR WINDOW DEFOGGER BUTTON (P.140)

LIGHT CONTROL SWITCH

(P.205)

MULTI-INFORMATION BUTTONS

(P.82)

＊

＊ ＊ ＊

1 : 2 : 3 :

To use the horn, press the center pad of the steering wheel. Only on vehicles equipped with navigation system. Refer to the navigation system manual. If equipped

133

2010 Odyssey０９／０４／１０　１６：１７：１１　３１ＳＨＪ６５０　０１３９　

Windshield Wipers and Washers

MIST The wipers run at high speed until you release the lever.

−

OFF

−

The wipers are not activated.

−

INT The length of the wipe interval is varied automatically according to vehicle’s speed.

Vary the delay by turning the adjustment ring. If you turn it to the shortest delay ( position), the wipers change to low speed operation when the vehicle speed exceeds 12 mph (20 km/h).

LO

−

The wipers run at low speed.

HI

−

The wipers run at high speed.

ADJUSTMENT RING

1. 2. 3. 4. 5. 6.

MIST OFF INT LO Low speed HI High speed Windshield washers

Intermittent

− − −

Push the right lever up or down to select a position.

134

−

Pull the

Windshield Washer wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever.

OnTouringmodels You can customize some windshield wiper settings. See page more information.

131

for

2010 Odyssey０９／０４／１０　１６：１７：２２　３１ＳＨＪ６５０　０１４０　

Windshield Wipers and Washers, Turn Signal and Headlights

Rear Window Wiper and Washer

Turn Signal and Headlights

When you shift the transmission to the reverse position with the front windshield wipers activated, the rear window wiper operates automatically.

When the wiper control lever is positioned as follows: