too quiet, choose high.
Audio System Lighting You can use the instrument panel brightness control knob to adjust the illumination of the audio system (see page 76). The audio system illuminates when the parking lights are on, even if the system is turned off.
121
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a Disc (Models without navigation system)
CD BUTTON
ꂹ ꂾ BUTTON
DISC SLOT
DISC EJECT ( ꁎ ) BUTTON
RANDOM BUTTON SEEK/SKIP ( ꀽ SEEK) BUTTON
SEEK/SKIP ( ꀾ SEEK) BUTTON
122
TITLE BUTTON
VOL/SELECT KNOB
ꂺ PLAY BUTTON
REPEAT BUTTON
SCAN BUTTON
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a Disc (Models without navigation system)
The in-dash disc player can also play
CD-Rs and CD-RWs compressed in
CD-TEXT, MP3, and WMA formats.
When playing a disc in MP3 or
WMA, you will see ‘‘MP3’’ or ‘‘WMA’’
in the display. You can see up to 99
folders, and select up to 999 tracks/
files.
To Play a Disc To load or play discs, the ignition switch must be in the ACCESSORY (I) or ON (II) position. You operate the in-dash disc player with the same controls used for the radio. To select the disc player, press the CD button. You will see ‘‘CD’’ in the display. The folder or track numbers are shown in the display. You can also select the displayed information with the TITLE button (see page 124). The system will continuously play a disc until you change modes.
Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.
NOTE: If a file on an MP3 or WMA disc is protected by digital rights management (DRM), the audio unit displays UNSUPPORTED, and then skips to the next file. Depending on the software the files were made with, it may not be possible to play some files, or display some text data. If you have a disc that is a combination of CD-DA tracks and MP3/WMA files, you can choose the format to listen by pressing the CD button. Video CDs and DVDs will not work in this unit. A disc compressed in AAC format cannot be played in this audio system.
CONTINUED
123
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a Disc (Models without navigation system)
ToLoadaDisc Insert a disc about halfway into the disc slot. The drive will pull the disc in the rest of the way to play it. You operate the disc player with the same controls used for the radio. The number of the current track is shown in the display. When playing a disc in MP3 or WMA, the numbers of the current folder and file are shown. The system will continuously play a disc until you change modes. You cannot load and play 3-inch (8-cm) discs in this unit. For information on how to handle and protect compact discs, see page 187.
TextDataDisplayFunction
Each time you press the TITLE
button, the display shows you the
text data on a disc, if the disc was
recorded with text data.
You can see the album, artist, and
track name in the display. If a disc is
recorded in MP3 or WMA, you can
see the folder and file name, and the
artist, album, and track tag.
With the folder name, you will see
the FOLDER indicator in the display.
The TRACK indicator is shown with
the file or track name.
When you press the TITLE button
while a disc without text data is
playing, you will see ‘‘NO INFO’’ on
the display.
The display shows up to about 16
characters of selected text data (the
folder name, file name, etc.).
124
indicator on the
If the text data has more than 16
characters, you will see the first 15
characters and the
display. Press and hold the TITLE
button until the next 16 characters
are shown. You can see up to about
31 characters of the text data.
If you press and hold the TITLE
button again, the display shows the
first 15 characters again.
If any letter is not available, it is
replaced with ‘‘ . ’’ (dot) in the
display. When the disc has no text
data, you will see ‘‘NO INFO’’ on the
display.
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a Disc (Models without navigation system)
ToChangeorSelectTracks/Files You can use the SEEK/SKIP button while a disc is playing to select passages and change tracks (files in MP3/WMA mode). In MP3/WMA mode, use the or on the disc, and use the SEEK/SKIP button to change files.
PLAY button to select folders
You will also see some text data under these conditions: ● When a new folder, file, or track is
selected.
● When you change the audio mode
to play a disc with text data or in MP3 or WMA.
● When you insert a disc, and the
system begins to play.
When playing a CD-DA with text data, the album and track name are shown in the display. With a disc in MP3 or WMA, the display shows the folder and file name.
button to skip
button, the player skips
SEEK/SKIP - Each time you press the forward to the beginning of the next track (files in MP3/WMA mode). Press the backward to the beginning of the current track. Press it again to skip to the beginning of the previous track. To move rapidly within a track, press button. and hold the You can also operate the track selection by using the VOL/SELECT knob. Press the VOL/SELECT knob and you will see ‘‘SEL’’ in the display. Turn the knob to switch the track number. Press the VOL/SELECT PLAY button to set your knob or selection. To turn it off, press the
or
button.
CONTINUED
125
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a Disc (Models without navigation system)
InMP3/WMAmode FOLDER SELECTION - To select or a different folder, press the PLAY button. Press the
PLAY button to skip to the
button to skip to the next folder, and the previous folder. You can also operate the folder and file selection by using the VOL/ SELECT knob. Press the VOL/ SELECT knob and you will see ‘‘SEL’’ in the display. Turn the knob to switch the folder number and press the knob to set your selection. Turn the knob to switch the file number and press the knob to your selection. To turn it off, press the
button repeatedly.
REPEAT (TRACK/FILE REPEAT) - To continuously replay a track (file in MP3/WMA mode), press the RPT button. You will see ‘‘RPT’’ in the display. Press and hold the RPT button to turn it off.
126
InMP3/WMAmode FOLDER-RANDOM - This feature, when activated, plays the files in the current folder in random order, rather than in the order they are compressed in MP3/WMA. To activate folder random play, press the RDM button. You will see ‘‘F-RDM’’ in the display. The system will then select and play files randomly. This continues until you deactivate folder random play by pressing and holding the RDM button. Each time you press the RDM button, the mode changes from folder random play, to within a disc random play, then to normal play.
InMP3/WMAmode FOLDER-REPEAT - This feature, when activated, replays all the files in the selected folder in the order they are compressed in MP3/WMA. To activate folder repeat mode, press the RPT button repeatedly until you see ‘‘F-RPT’’ in the display. The system continuously replays the current folder. Press and hold the RPT button to turn it off. Each time you press the RPT button, the mode changes from file repeat to folder repeat, then to normal play. RANDOM (Random within a disc) - This feature plays the tracks within a disc in random order. In MP3/WMA mode, all files in all folders are played in random order. To activate random mode, press the RDM button repeatedly until you see ‘‘RDM’’ in the display. Press and hold the RDM button to turn it off.
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
SCAN - The scan function samples all the tracks on the disc in the order they are recorded on the disc (all files in the selected folder in MP3 or WMA mode). To activate the scan feature, press the SCAN button. You will see ‘‘SCAN’’ in the display. You will get a 10 second sampling of each track/file on the disc/folder. Press and hold the SCAN button to get out of scan mode and play the last track sampled.
Playing a Disc (Models without navigation system)
InMP3/WMAmode
FOLDER-SCAN - This feature,
when activated, samples the first file
in each folder on the disc in the
order they are recorded. To activate
the folder scan feature, press the
SCAN button repeatedly. You will
see ‘‘F-SCAN’’ in the display. The
system will then play the first file in
the main folders for about 10
seconds. If you do nothing, the
system will then play the following
first files for 10 seconds each. When
the system samples the first file in all
folders, F-SCAN is cancelled, and the
system plays normally.
Each time you press the SCAN
button, the mode changes from
track/file scan to folder scan, then to
normal play.
) to
To Stop Playing a Disc Press the eject button ( remove the disc. If you eject the disc, but do not remove it from the slot, the system will automatically reload it after 10 seconds and put it in pause mode. To begin playing, press the CD button. Press the FM/AM button to switch to the radio while a disc is playing. Press the CD button to play the disc. If you turn the system off while a disc is playing, either with the power ( button or by turning off the ignition switch, the disc will stay in the drive. When you turn the system back on, the disc will begin playing where it left off. Protecting Discs For information on how to handle and protect compact discs, see page 187.
127
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Disc Player Error Messages (Models without navigation system)
Error Message
Cause
Solution
HEAT ERROR
UNSUPPORTED
High Temperature Track/File format not supported
BAD DISC
PLEASE CHECK
OWNERS
MANUAL PUSH
EJECT
BAD DISC
PLEASE CHECK
OWNERS MANUAL BAD DISC
OWNERS MANUAL
PLEASE CHECK
Mechanical Error
Servo Error
DISC Error
Will disappear when the temperature returns to normal. Current track will be skipped. The next supported track or file plays automatically. Press the EJECT button and pull out the disc. Check the disc for serious damage, signs of deformation, excessive scratches, and/or dirt (see page 188). Insert the disc again. If the code does not disappear, or the disc cannot be removed, consult your dealer. Do not try to force the disc out of the player.
Check the disc for serious damage, signs of deformation, excessive scratches, and/or dirt (see page 188).
The chart on the right explains the error messages you may see in the display while playing a disc. If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again. For the additional information on damaged discs, see page 188. The audio system will try to play the disc. If there is still a problem, the error message will reappear. Press the eject button, and pull out the disc. Insert a different disc. If the new disc plays, there is a problem with the first disc. If the error message cycle repeats and you cannot clear it, take your vehicle to a dealer.
128
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing an iPod® (Models without navigation system)
All models except Canadian DX, DX-A, and LX models
USB INDICATOR
iPod INDICATOR
ꂹ ꂾ BUTTON
AUX BUTTON
POWER ( ꂻ ) BUTTON
ꀾ SEEK (SKIP -) BUTTON
TITLE BUTTON
VOL/SELECT KNOB
ꂺ PLAY BUTTON
REPEAT BUTTON
RANDOM BUTTON ꀽ SEEK (SKIP +) BUTTON
CONTINUED
129
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing an iPod® (Models without navigation system)
Model iPod classic (80/160 G) iPod classic (120 G) iPod with video (iPod 5th generation) iPod nano iPod nano 2nd generation iPod nano 3rd generation iPod nano 4th generation iPod nano 5th generation iPod touch iPod touch 2nd generation
This system may not work with all software versions of these devices.
NOTE: ● Do not connect your iPod using a
HUB.
● Do not keep the iPod in the
vehicle. Direct sunlight and high heat will damage it.
● Do not use an extension cable between the USB adapter cable equipped with your vehicle and your dock connector.
● We recommend backing up your
data before playing it.
● Some devices cannot be powered or charged via the USB adapter. If this is the case, use the accessory adapter to supply power to your device.
To Play an iPodꭂ This audio system can operate the audio files on the iPodꭂ with the same controls used for the in-dash disc player. To play an iPod, connect it to the USB adapter cable in the upper glove box by using your dock connector, then press the AUX button. The ignition switch must be in the ACCESSORY (I) or ON (II) position. The iPod will also be recharged with the ignition switch in these positions. The audio system reads and plays sound files to be playable on the iPod. The system cannot operate an iPod as a mass storage device. The system will only play songs stored on the iPod with iTunes. iPod and iTunes are registered trademarks owned by Apple Inc. iPod models confirmed to be compatible with your audio system using the USB adapter cable are:
130
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing an iPod® (Models without navigation system)
ConnectinganiPod
DOCK CONNECTOR
USB CONNECTOR
USB ADAPTER CABLE 1. Open the upper glove box, and pull
out the USB adapter cable.
USB CONNECTOR
2. Connect your dock connector to the iPod correctly and securely. 3. Install the dock connector to the
USB connector securely.
TextDataDisplayFunction Each time you press the TITLE button the display mode switches between the album name, the song name, the artist name, or name off (which turns off the text display).
CONTINUED
131
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing an iPod® (Models without navigation system)
The display shows up to about 16
characters of the selected data. If the
text data has more than 16
characters, you will see the first 15
characters and the
display. Press and hold the TITLE
button until the next 16 characters
are shown.
indicator in the
ToChangeorSelectFiles Use the SKIP button while an iPod is playing to select passages and change files.
SKIP - Each time you press the (SKIP +) button, the system skips forward to the beginning of the next (SKIP -) button, file. Press the to skip backward to the beginning of the current file. Press it again to skip to the beginning of the previous file. To move rapidly within a file, press ) of and hold either side ( the SKIP button.
or
132
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing an iPod® (Models without navigation system)
The display shows items on the selected list. Turn the VOL/SELECT knob to select an item, then press the VOL/SELECT knob to set your selection. If you select ‘‘ALL,’’ all available files on the selected list are played. button goes back Pressing the to the previous display and pressing the TITLE button cancels this setting mode.
ToSelectRepeatorShuffleMode: You can select any type of repeat and shuffle mode by using the RPT button or the RDM button. REPEAT - This feature continuously plays a file. To activate the repeat feature, press the RPT button. You will see ‘‘RPT’’ in the display. To turn it off, press the RPT button again. SHUFFLE ALL - This feature plays all available files in a selected list (playlists, artists, albums or songs) in random order. To activate the shuffle all feature, press the RDM button. You will see ‘‘RDM’’ in the display. To turn it off, press and hold the RDM button.
Press the VOL/SELECT knob.
You can also select a file from any list on the iPod menu: playlists, artists, albums and songs, by using the VOL/SELECT knob. Push the VOL/ SELECT knob to switch the display to an iPod menu, then turn the VOL/ SELECT knob to select a desired list. Press the VOL/SELECT knob to set your selection.
CONTINUED
133
When you disconnect the iPod while it is playing, the display shows ‘‘USB NO DATA.’’ iPod Error Messages If you see an error message in the display, see page 135.
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing an iPod® (Models without navigation system)
SHUFFLE ALBUM - This feature plays all available albums in a selected list (playlists, artists, albums or songs) in random order. The files in each album are played in the recorded order. To activate the shuffle album feature, press the RDM button repeatedly. You will see ‘‘F-RDM’’ in the display. To turn it off, press and hold the RDM button. Each time you press the RDM button, the mode changes from shuffle all play to shuffle album play, then to normal play.
To Stop Playing Your iPod To play the radio when an iPod is playing, press the FM/AM button. If a disc is in the audio unit, press the CD button to play the disc. DisconnectinganiPod You can disconnect the iPod at any time when you see the ‘‘OK to Disconnect’’ messageꭧ in the iPod display. Always make sure you see ‘‘OK to Disconnect’’ message in the iPod display before you disconnect it. Make sure to follow the iPod's instructions on how to disconnect the dock connector from the USB adapter cable. ꭧ: The displayed message may vary on models or versions. On some models, there is no message to disconnect. If you reconnect the same iPod, the system may begin playing where it left off, depending on what mode the iPod is in when it is reconnected.
134
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
If you see an error message on the audio display while playing an iPod, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer.
iPod® Error Messages (Models without navigation system)
Error Message
Cause
Solution
USB ERROR
USB ROM Error
PLEASE CHECK
BAD USB DEVICE
OWNERS MANUAL
Abnormal power source
iPod NO SONG
No files in iPod
UNSUPPORTED
VER.
Use of unsupported iPod
CONNECT
RETRY
Recognition failure of iPod
There is a problem with the USB adapter unit. Appears when the overcurrent protection feature of the system stops supplying power to USB because an incompatible device is connected. Disconnect the device. Then, turn the audio system off, and turn it on again. Do not reconnect the device that caused the error. Appears when the iPod is empty. Store some files in the iPod. Appears when an unsupported iPod is connected. See page 130 for the specification information for iPods. If it appears when a supported iPod is connected, update the iPod software to the newer version. Appears when the system does not acknowledge the iPod. Reconnect the iPod.
135
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a USB Flash Memory Device (Models without navigation system)
All models except Canadian DX, DX-A, and LX models
USB INDICATOR
ꂹ ꂾ BUTTON
AUX BUTTON
POWER ( ꂻ ) BUTTON
ꀾ SEEK (SKIP -) BUTTON
136
RANDOM BUTTON ꀽ SEEK (SKIP +) BUTTON
TITLE BUTTON
VOL/SELECT KNOB
ꂺ PLAY BUTTON
REPEAT BUTTON
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a USB Flash Memory Device (Models without navigation system)
To Play a USB Flash Memory Device This audio system can operate the audio files on a USB flash memory device with the same controls used for the in-dash disc player. To play a USB flash memory device, connect it to the USB adapter cable in the upper glove box, then press the AUX button. The ignition switch must be in the ACCESSORY (I) or ON (II) position. The audio system reads and plays the audio files on the USB flash memory device in MP3, WMA or AACꭧ formats. Depending on the format, the display shows MP3, WMA or AAC when a USB flash memory device is playing. The USB flash memory device limit is up to 700 folders or up to 65535 files. ꭧ: Only AAC format files recorded with iTunes are playable on this audio unit.
The recommended USB flash memory devices are 256 Mbyte or higher, and formatted with the FAT file system. Some digital audio players may be compatible as well. Some USB flash memory devices (such as devices with security lockout features, etc.) will not work in this audio unit. NOTE: ● Do not use a device such as a card reader or hard drive as the device or your files may be damaged. ● Do not connect your USB flash
memory device using a HUB.
● Do not use an extension cable to the USB adapter cable equipped with your vehicle.
● Do not keep the USB flash
memory device in the vehicle. Direct sunlight and high heat will damage it.
● We recommend backing up your
data before playing a USB flash memory device.
● Depending on the type and
number of files, it may take some time before they begin to play. ● Depending on the software the
files were made with, it may not be possible to play some files, or display some text data.
● Some devices cannot be powered or charged via the USB adapter. If this is the case, use the accessory adapter to supply power to your device.
CONTINUED
137
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a USB Flash Memory Device (Models without navigation system)
Even if recorded in MP3, WMA or AAC format, a file with unsupported version cannot be played. If the system finds it, the audio unit displays UNSUPPORTED, and then skips to the next file.
In WMA or AAC format, DRM (digital rights management) files cannot be played. If the system finds a DRM file, the audio unit displays UNPLAYABLE FILE, and then skips to the next file.
ConnectingaUSBFlashMemory Device
USB CONNECTOR
USB ADAPTER CABLE 1. Open the upper glove box, and pull
out the USB adapter cable.
138
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a USB Flash Memory Device (Models without navigation system)
TextDataDisplayFunction
Each time you press the TITLE
button, the display mode shows you
in sequence, the folder name, the file
name, the artist name, the album
name, the song name, or name off
(which turns off the text display).
The display shows up to about 16
characters of the selected data. If the
text data has more than 16
characters, you will see the first 15
characters and the
display. Press and hold the TITLE
button until the next 16 characters
are shown.
indicator in the
USB CONNECTOR
2. Connect the USB flash memory
device to the USB connector correctly and securely.
When the USB flash memory device is connected, the USB indicator is shown in the display.
ToChangeorSelectFiles Use the SKIP button while a USB flash memory device is playing to select passages and change files. SKIP - Each time you press the (SKIP +) button, the system skips forward to the beginning of the next (SKIP -) button, file. Press the to skip backward to the beginning of the current file. Press it again to skip to the beginning of the previous file. To move rapidly within a file, press ) of and hold either side ( the SKIP button. FOLDER SELECTION - To select a different folder, press the button or
PLAY button. Press the
or
button to skip to the next
folder, and press the to skip to the beginning of the previous folder.
PLAY button
CONTINUED
139
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a USB Flash Memory Device (Models without navigation system)
ToSelectaFilefromFolderandFile Lists
Folder Selection
Press the VOL/SELECT knob.
Track Selection
You can also select a folder or file by using the VOL/SELECT knob. Push the VOL/SELECT knob to switch the display to the folder or file list, then turn the VOL/SELECT knob to select a folder or file. Press the VOL/ SELECT knob to set your selection. button goes back Pressing the to the previous display and pressing the TITLE button cancels this setting mode.
140
ToSelectRepeat,RandomorScan Mode: You can select any type of repeat, random and scan modes by using the RPT button or RDM button, or SCAN button. REPEAT - This feature continuously plays a file. To activate the repeat feature, press the RPT button. You will see ‘‘RPT’’ in the display. To turn it off, press and hold the RPT button. FOLDER REPEAT- This feature replays all the files in the selected folder in the order they are stored. To activate the folder repeat feature, press the RPT button repeatedly. You will see ‘‘F-RPT’’ in the display. To turn it off, press and hold the RPT button. Each time you press the RPT button, the mode changes from file repeat to folder repeat, then to normal play.
RANDOM - This feature plays all the files in random order. To activate the track random feature, press the RDM button. You will see ‘‘RDM’’ in the display. To turn it off, press and hold the RDM button. FOLDER RANDOM- This feature plays the files in the selected folder in random order. To activate the folder random feature, press the RDM button repeatedly. You will see ‘‘F-RDM’’ in the display. To turn it off, press and hold the RDM button. Each time you press the RDM button, the mode changes from track random play to folder random play, then to normal play.
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a USB Flash Memory Device (Models without navigation system)
SCAN - This feature samples all files in the selected folder in the order they are stored. To activate the scan feature, press the SCAN button. You will see ‘‘SCAN’’ in the display. You will get a 10 second sampling of each file in the folder. Press and hold the SCAN button to get out of the scan mode and play the last file sampled. FOLDER SCAN- This feature samples the first file in each folder in the order they are stored. To activate the folder scan feature, press the SCAN button repeatedly. You will see ‘‘F-SCAN’’ in the display. You will get a 10 second sampling of each first file in the folder(s). Press and hold the SCAN button to get out of the folder scan mode and play the last file sampled. Each time you press the SCAN button, the mode changes from file scan to folder scan, then to normal play.
To Stop Playing a USB Flash Memory Device To play the radio when a USB flash memory device is playing, press the FM/AM button. If a disc is in the audio unit, press the CD button to play the disc. DisconnectingaUSBFlashMemory Device You can disconnect the USB flash memory device in any time even if the USB mode is selected on the audio system. Always follow the USB flash memory device's instructions when you remove it. When you disconnect the USB flash memory device while it is playing, the display shows ‘‘USB NO DATA.’’ If you reconnect the same USB flash memory device, the system will begin playing where it left off.
USB Flash Memory Device Error Messages If you see an error message in the display, see page 142.
141
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
USB Flash Memory Device Error Messages (Models without navigation system)
Error Message
Cause
Solution
USB ERROR
USB ROM Error
PLEASE CHECK
BAD USB DEVICE
OWNERS MANUAL
Abnormal power source
UNPLAYABLE
FILE
Use of unsupported files
USB NO SONG
No files in USB flash memory device
UNSUPPORTED
Use of unsupported USB flash memory device
There is a problem with the USB adapter unit. Appears when the overcurrent protection feature of the system stops supplying power to USB because an incompatible device is connected. Disconnect the device. Then, turn the audio system off, and turn it on again. Do not reconnect the device that caused the error. Appears when the files in the USB flash memory device are DRM or an unsupported format. This error message appears for about 3 seconds, then plays the next song. Appears when the USB flash memory device is empty or there are no MP3, WMA, or AAC files in the USB flash memory device. Save some MP3, WMA, or AAC files in the USB flash memory device. Appears when an unsupported device is connected. See page 137 for the specification information for the USB flash memory device. If it appears when a supported device is connected, reconnect the device.
If you see an error message on the audio display while playing a USB flash memory device, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer.
142
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing the AM/FM Radio (Models with navigation system)
POWER/VOLUME KNOB
FM1 ICON
AM ICON
SOUND ICON
FM2 ICON
AUTO SELECT ICON
BACK GROUND ICON
AM/FM BUTTON
AUDIO BUTTON SCAN BUTTON
TUNE BAR
PRESET BUTTONS
CONTINUED
143
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing the AM/FM Radio (Models with navigation system)
Voice Control System In addition to the standard audio controls, the audio system in your vehicle can be operated using the voice control system. See the navigation system manual for complete details. To Play the AM/FM Radio The ignition switch must be in the ACCESSORY (I) or ON (II) position. Turn the system on by pushing the power/volume knob or the AM/FM button. Adjust the volume by turning the power/volume knob. Pushing the AUDIO button will also turn on the system.
You can also operate the audio system without using the control icons on the audio screen. Use the control buttons on the left side of the screen. The status bar appears on the bottom of the screen each time you operate any of the control buttons. On the navigation screen, you can also see audio information by touching the AUDIO INFO icon on the lower of the screen. The band and frequency that the radio was last turned to are displayed. To change bands, press the AM/FM button, or touch the desired band icon (FM1, FM2, or AM). On the FM band, STEREO will be displayed if the station is broadcasting in stereo. Stereo reproduction on AM is not available.
144
To Select a Station You can use any of five methods to find radio stations on the selected band: tune, seek, scan, the preset buttons, and auto select. TUNE - Use the TUNE bar to tune the radio to a desired frequency. Press the a higher frequency, and press the side to tune to a lower frequency. Press and hold the TUNE bar until you hear two beeps to change the frequency rapidly. Release the bar when the display reaches the desired frequency.
side of the bar to tune to
side of the
or
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing the AM/FM Radio (Models with navigation system)
or
side of the
SEEK - The SEEK function searches up and down from the current frequency to find a station with a strong signal. To activate it, press and hold the TUNE bar until you hear a beep, then release it. SCAN - The SCAN function samples all stations with strong signals on the selected band. To activate it, press the SCAN button, then release it. You will see SCAN in the display. The system will scan for a station with a strong signal. When it finds one, it will stop and play that station for about 10 seconds.
If you do nothing, the system will then scan for the next strong station and play it for 10 seconds. When it plays a station you want to listen to, press the SCAN button again. Preset - Each preset button can store one frequency on AM and two frequencies on FM. 1. Select the desired band, AM or FM. FM1 and FM2 let you store two frequencies with each preset button.
2. Use the tune, seek, or scan
function to tune the radio to a desired station.
3. Pick a preset button, and hold it
until you hear a beep.
4. Repeat steps 1 through 3 to store a
total of six stations on AM and twelve stations on FM.
Each preset button's frequency is shown on the bottom of the audio display.
CONTINUED
145
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing the AM/FM Radio (Models with navigation system)
AUTO SELECT - If you are traveling far from home and can no longer receive your preset stations, you can use the auto select feature to find stations in the local area. Press the AUDIO button to view the audio control icons, then touch the AUTO SEL icon. You will see AUTO SEL flashing in the display, and the system goes into scan mode for several seconds. It stores the frequencies of six AM, and twelve FM stations in the preset buttons.
You will see a ‘‘0’’ displayed after pressing a preset button if auto select cannot find a strong station for every preset button. If you do not like the stations auto select has stored, you can store other frequencies on the preset buttons as previously described. Toturnoffautoselect, touch the AUTO SEL icon . This restores the presets you originally set. For information on FM/AM radio frequencies and reception, see page 185.
Adjusting the Sound
SOUND ICON
You can adjust the sound on the navigation screen. To adjust the sound, push the AUDIO button, then enter the sound grid by touching the SOUND icon on the display.
146
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing the AM/FM Radio (Models with navigation system)
SPEAKER SETTING
BASS/TREBLE SETTING
BASS - Adjusts the bass. TREBLE - Adjusts the treble. To adjust the treble and bass, touch or on each side of the treble or bass adjustment bar. The adjustment bar on the right lower display shows you the current setting.
FADER - Adjusts the front-to-back strength of the sound. To adjust the front/rear fader, touch the FR or RR icon. BALANCE - Adjusts the side-to- side strength of the sound. To adjust the left/right balance, touch the L or R icon. The right upper display shows you the current setting of the sound strength coming from each speaker. SVC (speed-sensitive volume compensation) - The SVC mode controls the volume based on vehicle speed. The faster you go, the louder the audio volume becomes. As you slow down, the audio volume decreases. Touch the appropriate icon (Low, Mid, Hi, Off) to select the mode.
If you feel the sound is too loud, choose low. If you feel the sound is too quiet, choose Hi. You can also select the icon with the joystick. Move it up and down to move the highlighting and scroll through lists. Select the icon, then enter the joystick. The system will return to the audio display about 10 seconds after you stop adjusting a mode.
CONTINUED
147
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing the AM/FM Radio (Models with navigation system)
ScreenMode You can select the background screen to display the sound level. There are three screen modes: level (the sound level is shown with the vertical bars), spectrum analysis (the sound level appears as ripples of water), and off. Each time you touch the background icon, the display changes.
Audio System Lighting You can use the instrument panel brightness control knob to adjust the illumination of the control panel (see page 76). The audio system illuminates when the parking lights are on, even if the radio is turned off.
148
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a Disc (Models with navigation system)
CD ICON
POWER/VOLUME KNOB
OPEN BUTTON
CD/AUX BUTTON
AUDIO BUTTON
SCAN BUTTON
TUNE FOLDER BAR
RANDOM BUTTON
FAST FORWARD BUTTON REWIND BUTTON
SKIP - BUTTON
SKIP + BUTTON
REPEAT BUTTON
JOYSTICK
CONTINUED
149
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a Disc (Models with navigation system)
If you have a disc that is a combination of CD-DA tracks and MP3/WMA files, you can choose the format to listen by pressing and holding CD/AUX button until you hear a beep. Video CDs and DVD discs do not work in this unit. A disc compressed in AAC format cannot be played in this audio system.
NOTE: If a file on an MP3 or WMA disc is protected by digital rights management (DRM), the audio unit displays FILE ERROR, and then skips to the next file. Depending on the software the files were made with, it may not be possible to play some files, or display some text data.
To Play a Disc (In-dash single player) You operate the in-dash disc player with the same controls used for the radio. To load or play discs, the ignition switch must be in the ACCESSORY (I) or ON (II) position.
Do not use discs with adhesive labels. The label can curl up and cause the disc to jam in the unit.
This audio system can also play CD-Rs and CD-RWs compressed in MP3 or WMA formats. When playing a disc in MP3, you will see ‘‘MP3’’ on the screen. In WMA format, ‘‘WMA’’ will appear on the screen. You can select up to 255 folders and play up to 999 tracks. If the disc has a complex structure, it takes a while to read the disc before the system begins to play it.
150
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a Disc (Models with navigation system)
ToLoadaDisc
DISC SLOT
CLOSE BUTTON
OPEN BUTTON The in-dash disc player is behind the navigation screen. To use the disc player, press the OPEN button beside the screen. The screen folds back, and the disc slot appears.
Insert a disc about halfway into the disc slot. The drive will pull the disc in the rest of the way and begin to play it. You cannot load and play 3-inch (8-cm) discs in this system.
To return the screen to the upright position, press the CLOSE button on the edge of the screen panel. Do not use the folded screen as a tray. If you put a cup, for example, on the screen, the liquid inside the cup may spill on the screen when you go over a bump.
CONTINUED
151
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a Disc (Models with navigation system)
ToChangeorSelectTracks/Files
PRESET BUTTON'S FUNCTION
PRESET BUTTONS
You can use the preset buttons while a disc is playing to select passages and change tracks (files in MP3 or WMA mode). Each preset button's function is shown on the bottom of the screen.
You can also select an icon with the joystick. Move it to left, right, up, or down to change the highlighting and scroll through lists. Then press the ENT on the top of the joystick to select the icon. SKIP - Each time you press (preset 6), the player skips forward to the beginning of the next track (file in MP3 or WMA mode). Press (preset 5), to skip backward to the beginning of the current track. Press it again to skip to the beginning of the previous track. FF/REW - To move rapidly within a track/file, press and hold (preset 4) or
(preset 3).
Press the AUDIO button beside the
screen to show the audio display and
operate the in-dash disc player.
You can also operate the audio
system without using the control
icons on the audio screen. Press the
CD/AUX button. The status bar
appears on the bottom of the screen.
On the navigation screen, you can
see the audio information whenever
you touch the AUDIO INFO or
TRACK LIST icons on the lower of
the screen.
When playing a CD recorded with
text data, the track, album, and artist
name are shown on the audio
display. When playing a disc in MP3
or WMA, the folder number and
name, the file number and name, the
artist name, and the elapsed time are
shown. The system will continuously
play a disc until you change modes.
If the disc was not recorded with text
data, it will not be displayed.
152
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
side of the TUNE
side to move to the
InMP3orWMAmode FOLDER SELECTION - To select a different folder, press either side of the TUNE FOLDER bar to move to the beginning of the next folder. Press the FOLDER bar to skip to the next folder, and the beginning of the current folder. Press it again to skip to the beginning of the previous folder. TRACK REPEAT (FILE REPEAT) - To continuously replay a track (file in MP3 or WMA mode), press the RPT button (preset 1). You will see ‘‘TRACK REPEAT’’ in the display. Press the RPT button again to turn it off.
Playing a Disc (Models with navigation system)
InMP3orWMAmode FOLDER RANDOM - This feature, when activated, plays all files in the selected folder in random order, rather than in the order they are compressed. To activate folder random, press and hold the RDM button. You will see ‘‘FOLDER RANDOM’’ in the display. The system then selects and plays files randomly. This continues until you deactivate folder random by pressing the RDM button again, or if you select a different folder with the TUNE FOLDER bar.
InMP3orWMAmode FOLDER REPEAT - This feature, when activated, replays all files in the selected folder in the order they are compressed. To activate folder repeat, press and hold the RPT button (preset 1) for 2 seconds. You will see ‘‘FOLDER REPEAT’’ in the display. The system continuously replays the current folder. Press the RPT button again to turn it off. Selecting a different folder with the TUNE FOLDER bar also turns off folder repeat. TRACK RANDOM (Random within a disc/folder) - This feature plays the tracks/files within a disc in random order. To activate track random, press the RDM button (preset 2). You will see ‘‘TRACK RANDOM’’ in the display. Press the RDM button again to return to normal play.
CONTINUED
153
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a Disc (Models with navigation system)
SCAN (TRACK/FILE SCAN) - The scan function samples all tracks (files in MP3 or WMA) in the order they were recorded. To activate scan, press the SCAN button. You will see ‘‘TRACK SCAN’’ in the display. You will get a 10 second sampling of each track/file on the disc. Press the SCAN button to get out of scan mode and play the last track/file sampled. Pressing either SKIP button (preset 5 or 6) also turns off scan.
InMP3orWMAmode
FOLDER SCAN - This feature,
when activated, samples all the first
files in each folder on the disc in
order. To activate folder scan, press
and hold the SCAN button for 2
seconds. You will see ‘‘FOLDER
SCAN’’ in the display.
The system plays the first file in each
folder for about 10 seconds. If you do
nothing, the system then plays the
first file in each folder for 10 seconds
each. After playing the first file of the
last folder, the system goes to normal
play.
Pressing either SKIP button (preset
5 or 6), or selecting a different folder
with the TUNE FOLDER bar, or
pressing the SCAN button, also turns
off folder scan.
UsingaTrackList
FOLDER ICON
TRACK/FILE ICON
RETURN ICON
FOLDER NUMBER You can also select a track/file directly from a track list on the audio display. Press the AUDIO button to show the audio display, then touch the Track List icon. The track list menu appears on the display.
154
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a Disc (Models with navigation system)
Select the desired track/file by touching the icon on the display. The selected icon will be highlighted in blue. The system begins to play the selected track/file. With a disc in MP3 or WMA, touch the folder icon on the upper left of the screen to move to the root folder. The current folder is highlighted in blue.
When playing a CD recorded with text data, each track name is shown on the audio display. With a disc recorded in MP3 or WMA, the folder number and the location are also displayed. If the disc was not recorded with text data, only the track number is shown. To scroll through the display, touch icon on the side of the the screen. To go back to the previous display, touch the Return icon on the screen.
or
To Stop Playing a Disc To play the radio when a disc is playing, press the AM/FM button or touch the FM1, FM2, or AM icon. If a PC card is in the audio unit, touch the CARD icon to play the PC card. Press the CD/AUX button again or touch the CD icon to switch back to the in-dash disc player. If you turn the system off while a disc is playing, either with the power/ volume knob or by turning off the ignition switch, the disc will stay in the drive. When you turn the system back on, the disc will begin playing where it left off.
CONTINUED
155
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a Disc (Models with navigation system)
Protecting Discs For information on how to handle and protect discs, see page 187.
RemovingaDisc To remove a disc from the audio unit, fold back the screen by pressing the OPEN button (see page 151). Press ) to remove the disc eject button ( the disc. If you eject the disc, but do not remove it from the slot, the system will automatically reload it after 10 seconds and put it in pause mode. To begin playing, press the CD/AUX button. To return the screen to the upright position, press the CLOSE button. You cannot close the screen if a disc is partially inserted into its slot. You can also eject the disc when the ignition switch is off.
156
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Disc Player Error Messages (Models with navigation system)
If you see an error message in the display while playing a disc, find the cause in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. The chart on the right explains the error messages you may see in the display while playing a disc. If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again. The audio system will try to play the disc. If there is still a problem, the error message will reappear. Press the eject button, and pull out the disc. Insert a different disc. If the new disc plays, there is a problem with the first disc. If the error message cycle repeats and you cannot clear it, take your vehicle to a dealer.
Error Message
Cause
Solution
CHECK DISC
FOCUS Error
MECH ERROR
Mechanical Error
CHECK DISC
Disc Format Error
HEAT ERROR
High Temperature
Press the eject button, and pull out the disc. Make sure it is inserted correctly in the disc player. Make sure the disc is not scratched or damaged. Press the eject button, and pull out the disc. Check the disc for damage or deformation. If the disc cannot be pulled out, or the error message does not disappear after the disc is ejected, see your dealer. Press the eject button, and pull out the disc. Check the disc for damage or deformation. Will disappear when the temperature returns to normal.
157
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a PC card (Models with navigation system)
POWER/VOLUME KNOB
PC CARD ICON
TRACK LIST ICON
JOYSTICK
PLAY MODE ICON
OPEN BUTTON
CD/AUX BUTTON AUDIO BUTTON
SCAN BUTTON
TUNE FOLDER BAR
158
REPEAT BUTTON
REWIND BUTTON
SKIP - BUTTON
RANDOM BUTTON
FAST FORWARD BUTTON
SKIP + BUTTON
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a PC card (Models with navigation system)
To Play a PC card
You operate the PC card player with
the same controls used for the radio
and the in-dash disc player. To load
or play a card, the ignition switch
must be in the ACCESSORY (I) or
ON (II) position.
The PC card player reads and plays
cards in MP3 or WMA formats.
Depending on the format, the screen
will indicate ‘‘MP3’’ or ‘‘WMA’’ when
a card is playing. The card limit of
the player is 255 folders and 999
tracks. If the card has a complex
structure, it takes some time for the
system to begin playing it.
Based on PCMCIA 2.1/JEIDA 4.2,
the recommended PC cards for the
PC card reader are:
CompactFlash
Flash ATA
SD memory card
Always use the recommended memory card with the appropriate adapter (if an adapter is needed). Some memory cards will not work in this unit. NOTE: ● When you insert a PC card into the
slot, make sure you put it in straight. If you cannot insert it, remove it, and insert again. ● Do not keep PC cards in the
vehicle. Direct sunlight and high heat will damage them.
● To avoid damaging the card
reader, do not insert hard disc drive cards into the PC card slot.
● You cannot close the screen (move it to the upright position) until the PC card is inserted all the way into its slot or removed.
● Never insert foreign objects into
the PC card slot.
● Depending on the type of
encoding and writing software used, there may be causes where character information does not display properly.
CONTINUED
159
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a PC card (Models with navigation system)
In WMA format, DRM (digital rights management) files cannot be played. If the system finds a DRM file, it skips that file and plays the next available folder or file.
LoadingaPCCard
PC CARD SLOT
The PC card slot is behind the navigation screen. To use the PC card player, press the OPEN button beside the screen. The screen folds back, and the PC card slot appears.
Insert a PC card straight into the slot. The drive will read the PC card and begin to play it. Return the screen to the upright position by pressing the CLOSE button on the edge of the screen panel. Press the AUDIO button beside the screen to show the audio display and operate the PC card player. You can also operate the audio system without using the control icons on the audio screen. Press any of the appropriate control buttons. The status bar appears on the bottom of the screen. On the navigation screen, you can see the audio information whenever you touch the AUDIO INFO icon on the screen.
160
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a PC card (Models with navigation system)
ToSelectaPlayMode
PLAY MODE ICON
FOLDER MODE
MODE INDICATOR
PLAY MODE ICON
PLAY MODE ICON
ARTIST MODE
ALBUM MODE
There are three play modes: Folder, Artist, and Album. Touch the PLAY MODE icon, then choose one of the modes by touching its icon. When a mode is selected, it is highlighted in blue. ● Folder mode plays tracks in the
order they were added to the card.
● Artist mode plays tracks in
alphabetical order, by artist and song title.
● Album mode plays albums
(folders) in alphabetical order. If play mode information was not included in the tracks/files when they were added to the card, it will not be displayed on the screen.
MODE INDICATOR
MODE INDICATOR
CONTINUED
161
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a PC card (Models with navigation system)
PLAY MODE ICON
To select a play mode, push the AUDIO button to show the audio display, then touch the PLAY MODE icon on the display.
Select the desired mode by touching the appropriate icon, or move the joystick, then press the ENT.
After you select the play mode, the display changes to the selectable playing menu. If you select ‘‘Continue playing the current song,’’ the system goes into the selected play mode after playing the current file.
162
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
If you select ‘‘Play a new track list,’’ the system goes into the selected play mode immediately and begins to play the new track list. To go back to the previous screen, press the CANCEL button on the right side of the screen. To exit the play mode screens, press the AUDIO button.
Playing a PC card (Models with navigation system)
ToChangeorSelectTracks/Files
PRESET BUTTON'S FUNCTION
Icons on the screen can also be selected with the joystick. Move the joystick left or right and up or down until the icon is highlighted, then press the ENT on the top of the joystick to select the icon.
PRESET BUTTONS
You can use the preset buttons while a card is playing to select or change files. Each preset button's function is shown on the bottom of the screen.
CONTINUED
163
10/08/06 13:54:35 11 FIT MMC North America Owner's Manual 50 31TK6620 enu
Playing a PC card (Models with navigation system)
(preset 5), to skip
SKIP - Each time you press (preset 6), the player skips forward to the beginning of the next file. Press backward to the beginning of the current file. Press it again to skip to the beginning of the previous file. FF/REW - To move rapidly within (preset 4) a file, press and hold or FOLDER SELECTION - To select a different folder, press either side of the TUNE FOLDER bar to move to the beginning of the next folder. Press the FOLDER bar to skip to the next side to move to folder, and to the the beginning of the current folder. Press it again to skip to the beginning of the previous folder.
side of the TUNE
(preset 3).
TRACK REPEAT (FILE REPEAT)
- To continuously replay a file,
press the RPT button (preset 1). You
will see ‘‘TRACK REPEAT’’ in the
display. Press the RPT button again
to turn it off.
FOLDER/ARTIST/ALBUM
REPEAT - This feature, when
activated, replays all the files in the
selected folder/artist/album in the
order they are recorded or listed. To
activate each repeat mode, press and
hold the RPT button (preset 1) for 2
seconds. You will see ‘‘FOLDER
REPEAT, ARTIST REPEAT or
ALBUM REPEAT’’ in the display.
The system continuously replays the
current folder/artist/album. Press
and hold the RPT button again to
turn it off. Pressing the RDM button,
or selecting a different folder/artist/
album with the TUNE FOLDER bar