Login- Download PDF Manual
-
QRG
TOC
Index
Home
Continued
281
2013 CR-Z 13 CR-Z-31SZT6200.book 282 ページ ２０１２年１０月２５日 木曜日 午後９時９分
uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire
■ Distributing the Sealant in the Tire
Speed Restriction Label
1. Apply the speed restriction label to the
location as shown.
2. Drive the vehicle for about 10 minutes.
u Do not exceed 50 mph (80 km/h).
3. Stop the vehicle in a safe place.
1Distributing the Sealant in the Tire
Stop and recheck the air pressure after every 10 minutes of driving as necessary until you reach the nearest service station where you should have the tire permanently repaired or replaced.
Air Only Hose
4. Unscrew the air only hose (black) to remove
it from the sealant bottle.
Sealant Bottle
QRG
TOC
Index
Home
282
2013 CR-Z 13 CR-Z-31SZT6200.book 283 ページ ２０１２年１０月２５日 木曜日 午後９時９分
QRG
Air Only Hose (Black)
uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire
5. Recheck the air pressure using the air only
1Distributing the Sealant in the Tire
hose (black) on the compressor. u Do not turn the air compressor on to
check the pressure.
2 Inflating An Under-inflated Tire
P. 284
See the driver’s doorjamb or the specifications in this manual for the required air pressure.
2 Specifications P. 306
3WARNING
Running the engine with the vehicle in an enclosed or even partly enclosed area can cause a rapid build-up of toxic carbon monoxide. Breathing this colorless, odorless gas can cause unconsciousness and even death. Only run the engine to power the air compressor with the vehicle outdoors.
6. If the air pressure is:
u Less than 19 psi (130 kPa):
Do not add air or continue driving. The leak is too severe. Call for help and have your vehicle towed.
2 Emergency Towing P. 301
u The required air pressure or more:
Continue driving for another 10 minutes or until you reach the nearest service station. Do not exceed 50 mph (80 km/h).
u If the air pressure does not go down after the 10 minutes driving, you do not
need to check the pressure any more.
u Greater than 19 psi (130 kPa), but less than the required air pressure: Use the air compressor to inflate the tire to the required air pressure.
2 Inflating An Under-inflated Tire P. 284
Then drive carefully for 10 more minutes or until you reach the nearest service station. Do not exceed 50 mph (80 km/h).
u You should repeat this procedures as long as the air pressure is within this
range.
7. Repackage and properly stow the kit.
TOC
Index
Home
Continued
283
2013 CR-Z 1Inflating An Under-inflated Tire
NOTICE Do not operate the temporary tire repair kit compressor for more than 15 minutes. The accessory power socket and compressor can overheat and become permanently damaged.
13 CR-Z-31SZT6200.book 284 ページ ２０１２年１０月２５日 木曜日 午後９時９分
uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire
■ Inflating An Under-inflated Tire You can use the kit to inflate a non-punctured under-inflated tire. Air Only Hose (Black)
1. Pull the strap on the cargo area floor lid
and open the lid.
2 Getting Ready to Temporarily Repair
the Flat Tire P. 277
2. Remove the kit from the case.
3. Place the kit upright on flat ground near the tire to be inflated, away from traffic. Do not place the kit on its side.
4. Unscrew the air only hose (black) to
remove it from the sealant bottle.
5. Remove the valve cap.
Valve Cap
Air Only Hose (Black)
6. Attach the air only hose onto the tire valve
stem. Screw it until it is tight.
Valve Stem
QRG
TOC
Index
Home
284
2013 CR-Z 13 CR-Z-31SZT6200.book 285 ページ ２０１２年１０月２５日 木曜日 午後９時９分
uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire
Power Plug
Side Cover
Inflator Switch
7. Remove the side cover, then pull out the
1Inflating An Under-inflated Tire
power plug.
8. Plug in the compressor to the accessory
power socket. u Be careful not to pinch the cord in a
door or window.
9. Start the engine.
u Keep the engine running while injecting
air.
2 Carbon Monoxide Gas P. 62
10. Press the inflator switch to turn on the
compressor. u The compressor starts to inject air into
the tire.
11. Inflate the tire to the specified air pressure.
3WARNING
Running the engine with the vehicle in an enclosed or even partly enclosed area can cause a rapid build-up of toxic carbon monoxide. Breathing this colorless, odorless gas can cause unconsciousness and even death. Only run the engine to power the air compressor with the vehicle outdoors.
QRG
TOC
Pressure Relief Button
Index
Home
Inflator Switch
12. Turn off the inflator switch.
u Check the pressure gauge on the air
u If overinflated, press the pressure relief
compressor.
button.
13. Unplug the compressor from the
accessory power socket.
14. Unscrew the air only hose from the tire
valve stem. Reinstall the valve cap.
15. Press the pressure relief button until the
gauge returns to 0 psi (0 kPa).
16. Repackage and properly stow the kit.
285
2013 CR-Z 13 CR-Z-31SZT6200.book 286 ページ ２０１２年１０月２５日 木曜日 午後９時９分
Engine Does Not Start
QRG
Checking the Engine If the engine does not start, turn the ignition switch to START (e and check the starter.
1Checking the Engine
If you must start the vehicle immediately, use an assisting vehicle to jump start it.
2 Jump Starting P. 287
Starter condition
Starter doesn’t turn or turns over slowly. The 12 volt battery may be dead. Check each of the items on the right and respond accordingly.
Checklist
Check brightness of the interior light. Turn on interior lights and check brightness. ● If the interior lights are dim or do not come on at all
2 Checking the 12 Volt Battery P. 262
● If the interior lights come on normally
2 Inspecting and Changing Fuses P. 300
The starter turns over normally but the engine doesn’t start. There may be a problem with the fuse. Check each of the items on the right and respond accordingly.
Review the engine start procedure. Follow its instructions, and try to start the engine again. 2 Starting the Engine P. 178
Check the immobilizer system indicator. When the immobilizer system indicator is blinking, the engine cannot be started.2 Immobilizer System P. 106
Check the fuel level. There should be enough fuel in the tank. 2 Fuel Gauge P. 81
Check the fuse. Check all fuses, or have the vehicle checked by a dealer.2 Inspecting and Changing Fuses P. 300
If the problem continues:
2 Emergency Towing P. 301
TOC
Index
Home
286
2013 CR-Z 13 CR-Z-31SZT6200.book 287 ページ ２０１２年１０月２５日 木曜日 午後９時９分
Jump Starting
■ Jump Starting Procedure Turn off the power to electric devices, such as audio and lights. Turn off the engine, then open the hood.
Booster Battery
1. Connect the first jumper cable to your
vehicle's + terminal.
2. Connect the other end of the first jumper
cable to the booster battery + terminal. u Use a 12 volt booster battery only.
3. Connect the second jumper cable to the
booster battery - terminal.
4. Connect the other end of the second
jumper cable to the grounding strap as shown. Do not connect this jumper cable to any other part.
5. If your vehicle is connected to another
vehicle, start the assisting vehicle's engine and increase its rpm slightly.
6. Attempt to start your vehicle's engine. If it
turns over slowly, check that the jumper cables have good metal-to-metal contact.
1Jump Starting
3WARNING
A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby.
Keep all sparks, open flames, and smoking materials away from the battery.
Securely attach the jumper cables clips so that they do not come off when the engine vibrates. Also be careful not to tangle the jumper cables or allow the cable ends to touch each other while attaching or detaching the jumper cables.
Battery performance degrades in cold conditions and may prevent the engine from starting.
QRG
TOC
Index
Home
Continued
287
2013 CR-Z 13 CR-Z-31SZT6200.book 288 ページ ２０１２年１０月２５日 木曜日 午後９時９分
uuJump Startingu
■ What to Do After the Engine Starts Once your vehicle's engine has started, remove the jumper cables in the following
order.
1. Disconnect the jumper cable from your vehicle's ground.
2. Disconnect the other end of the jumper cable from the booster
battery - terminal.
3. Disconnect the jumper cable from your vehicle's + terminal.
4. Disconnect the other end of the jumper cable from the booster
battery + terminal.
Have your vehicle inspected by a nearby service station or a dealer.
QRG
TOC
Index
Home
288
2013 CR-Z 13 CR-Z-31SZT6200.book 289 ページ ２０１２年１０月２５日 木曜日 午後９時９分
Shift Lever Does Not Move
Automatic transmission (CVT) models Follow the procedure below if you cannot move the shift lever out of the (P position.
■ Releasing the Lock
1. Set the parking brake.
2. Remove the key from the ignition switch.
3. Wrap a cloth around the tip of a small flat-
tip screwdriver. Put it into the shift lock release slot as shown in the image, and remove the cover.
4. Insert the key into the shift lock release slot.
5. While pushing the key down, press the shift lever release button and place the shift lever into (N. u The lock is now released. Have the shift
lever checked by a dealer as soon as possible.
Slot
Cover
Release Button
Shift Lock Release Slot
QRG
TOC
Index
Home
289
2013 CR-Z 1How to Handle Overheating
3WARNING
Steam and spray from an overheated engine can seriously scald you.
Do not open the hood if steam is coming out.
NOTICE Continuing to drive with the high temperature indicator on may damage the engine.
13 CR-Z-31SZT6200.book 290 ページ ２０１２年１０月２５日 木曜日 午後９時９分
Overheating
QRG
How to Handle Overheating Overheating symptoms are as follows: • The high temperature indicator comes on or the engine suddenly loses power.
• Steam or spray comes out of the engine compartment.
■ First thing to do 1. Immediately park the vehicle in a safe place.
2. Turn off all accessories and turn on the hazard warning lights.
u No steam or spray present: Keep the engine running and open the hood. u Steam or spray is present: Turn off the engine and wait until it subsides.
Then open the hood.
TOC
Index
Home
290
2013 CR-Z 13 CR-Z-31SZT6200.book 291 ページ ２０１２年１０月２５日 木曜日 午後９時９分
QRG
■ Next thing to do
MAX
Reserve Tank
MIN
uuOverheatinguHow to Handle Overheating
1How to Handle Overheating
3WARNING
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.
If the coolant is leaking, contact a dealer for repairs.
Use water as an emergency/temporary measure only. Have a dealer flush the system with proper antifreeze as soon as possible.
1. Check that the cooling fan is operating and stop the engine once the high temperature indicator goes off. u If the cooling fan is not operating,
immediately stop the engine.
2. Once the engine has cooled down, inspect
the coolant level and check the cooling system components for leaks. u If the coolant level in the reserve tank is
low, add coolant until it reaches the MAX mark.
u If there is no coolant in the reserve tank, check that the radiator is cool. Cover the radiator cap with a heavy cloth and open the cap. If necessary, add coolant up to the base of the filler neck, and put the cap back on.
■ Last thing to do Once the engine has cooled sufficiently, restart it and check the high temperature indicator.
If the high temperature indicator is off, resume driving. If it stays on, contact a dealer for repairs.
TOC
Index
Home
291
2013 CR-Z 1If the Low Oil Pressure Indicator Comes On
NOTICE Running the engine with low oil pressure can cause serious mechanical damage almost immediately.
13 CR-Z-31SZT6200.book 292 ページ ２０１２年１０月２５日 木曜日 午後９時９分
Indicator, Coming On/Blinking
QRG
If the Low Oil Pressure Indicator Comes On
■ Reasons for the indicator to come on Comes on when the engine oil pressure is low.
■ What to do as soon as the indicator comes on 1. Immediately park the vehicle on level ground in a safe place.
2. If necessary, turn the hazard warning lights on.
■ What to do after parking the vehicle 1. Stop the engine and let it sit for about three minutes.
2. Open the hood and check the oil level.
u Add oil as necessary. 2 Oil Check P. 232
3. Start the engine and check the low oil pressure indicator.
u The light goes out: Start driving again. u The light does not go out within 10 seconds: Stop the engine and
contact a dealer for repairs immediately.
TOC
Index
Home
292
2013 CR-Z 13 CR-Z-31SZT6200.book 293 ページ ２０１２年１０月２５日 木曜日 午後９時９分
uuIndicator, Coming On/BlinkinguIf the Charging System Indicator Comes On
If the Charging System Indicator Comes On
QRG
■ Reasons for the indicator to come on Comes on when the 12 volt battery is not being charged.
■ What to do when the indicator comes on Turn off the climate control system, rear defogger, and other electrical systems, and immediately contact a dealer for repairs.
TOC
Index
Home
1If the Charging System Indicator Comes On
If you need to stop temporarily, do not turn off the engine. Restarting the engine may rapidly discharge the 12 volt battery.
Manual transmission models This indicator may also come on when the Auto Idle Stop function is activated for a while. Restart the engine.
2 Auto Idle Stop P. 194
Automatic transmission (CVT) models This indicator may also come on when the IMA battery charge drops below a desired level. The engine starts to recharge the battery.
2 Auto Idle Stop P. 191
The indicator goes off when the battery is being charged normally.
This indicator may blink after starting when the outside temperature is below -20°F (-30°C). It will stop blinking after the IMA battery warms up.
293
2013 CR-Z 1If the Malfunction Indicator Lamp Comes On or Blinks
NOTICE If you drive with the malfunction indicator lamp on, the emissions control system and the engine could be damaged.
If the malfunction indicator lamp blinks again when restarting the engine, drive to the nearest dealer at 31 mph (50 km/h) or less. Have your vehicle inspected.
13 CR-Z-31SZT6200.book 294 ページ ２０１２年１０月２５日 木曜日 午後９時９分
uuIndicator, Coming On/BlinkinguIf the Malfunction Indicator Lamp Comes On or Blinks
QRG
If the Malfunction Indicator Lamp Comes On or Blinks
■ Reasons for the indicator lamp to come on or blink • Comes on when there is a problem with the engine emissions control
system, or the fuel fill cap is missing, or loose.
• Blinks when engine misfiring is detected. ■ What to do when the indicator lamp comes on Avoid high speeds and immediately get your vehicle inspected at a dealer. ■ What to do when the indicator lamp blinks Park the vehicle in a safe place with no flammable items and wait at least ten minutes or more with the engine stopped until it cools.
■ Tighten Fuel Cap Message ■ The message appears on when: An evaporative system leak is detected. This may be caused by the fuel fill cap being loose or not being installed.
■ What to do when the message appears: 1. Stop the engine.
2. Check that the fuel fill cap is fully installed.
u If not, loosen the cap, and then retighten it until it clicks at least once.
3. Drive for several days of normal driving.
u The message should go off.
■ When the malfunction indicator lamp comes on Malfunction indicator lamp comes on if the system continues to detect a leak of gasoline vapor. If this happens, check the fuel fill cap using the procedures described above.
TOC
Index
Home
294
2013 CR-Z 13 CR-Z-31SZT6200.book 295 ページ ２０１２年１０月２５日 木曜日 午後９時９分
uuIndicator, Coming On/BlinkinguIf the Brake System Indicator (Red) Comes On
If the Brake System Indicator (Red) Comes On
QRG
U.S.
■ Reasons for the indicator to come on • The brake fluid is low.
• There is a malfunction in the brake system.
Canada
■ What to do when the indicator comes on while driving Press the brake pedal lightly to check pedal pressure. • If normal, check the brake fluid level the next time you stop.
• If abnormal, take immediate action. If necessary, downshift the
transmission to slow the vehicle using engine braking.
1If the Brake System Indicator (Red) Comes On Have your vehicle repaired immediately. It is dangerous to drive with low brake fluid. If there is no resistance from the brake pedal, stop immediately in a safe place. If necessary downshift the gears.
If the brake system indicator and ABS indicator come on simultaneously, the electronic brake distribution system is not working. This can result in vehicle instability under sudden braking. Have your vehicle inspected by a dealer immediately.
TOC
Index
Home
If the EPS System Indicator Comes On
1If the EPS System Indicator Comes On
■ Reasons for the indicator to come on • Comes on when there is a problem with EPS system.
• If you depress the accelerator pedal repeatedly to increase the engine
speed while the engine is idling, the indicator comes on, and sometimes the steering wheel becomes harder to operate.
■ What to do when the indicator comes on Stop the vehicle in a safe place and restart the engine. If the indicator comes on and stays on, immediately have your vehicle inspected by a dealer.
NOTICE If you repeatedly turn the steering wheel at an extremely low speed, or hold the steering wheel on the full left or right position for a while, the system heats up. The system goes into a protective mode, and limits its performance. The steering wheel becomes harder and harder to operate. Once the system cools down, EPS is restored. Repeated operation under these conditions can eventually damage the system.
295
2013 CR-Z 13 CR-Z-31SZT6200.book 296 ページ ２０１２年１０月２５日 木曜日 午後９時９分
uuIndicator, Coming On/BlinkinguIf the IMA Indicator Comes On
QRG
If the IMA Indicator Comes On
■ Reasons for the indicator to come on Comes on when there is a problem with the IMA system.
■ What to do when the indicator come on Avoid high speeds and immediately get your vehicle inspected by a dealer.
U.S. models If the Low Tire Pressure/ TPMS Indicator Comes On or Blinks
TOC
Index
Home
296
■ Reasons for the indicator to come on or blink A tire pressure is significantly low. If there is a problem with the TPMS or the compact spare tire * is installed, the indicator blinks for about one minute, and then stays on.
■ What to do when the indicator comes on Drive carefully and avoid abrupt cornering and hard braking. Stop your vehicle in a safe place. Check the tire pressure and adjust the pressure to the specified level. The specified tire pressure is on a label on the driver side doorjamb. ■ What to do when the indicator blinks, then remains on Have the tire inspected by a dealer as soon as possible. If the compact spare tire * causes the indicator to blink, change the tire to a full-size tire. The indicator goes off after driving for a few miles (kilometers).
* Not available on all models
1If the Low Tire Pressure/TPMS Indicator Comes On or Blinks
NOTICE Driving on an extremely underinflated tire can cause it to overheat. An overheated tire can fail. Always inflate your tires to the prescribed level.
2013 CR-Z 13 CR-Z-31SZT6200.book 297 ページ ２０１２年１０月２５日 木曜日 午後９時９分
Fuses
QRG
Fuse Locations If any electrical devices are not working, turn the ignition switch to LOCK (0 and check to see if any applicable fuse is blown.
■ Engine Compartment Fuse
Box
Located near the + terminal on the 12 volt battery.
1. Pull on the tab to release the front of the
cover.
2. Pull up the cover by pushing the two tabs
as shown. Replacement of engine compartment fuses should be done by a dealer.
■ Circuit protected and fuse rating
Circuit Protected
Battery
EPS
Horn, Stop, Hazard
Amps 100 A 70 A 20 A
Fuse Box
Fuse locations are shown on the fuse box cover.
Locate the fuse in question by the fuse number and box cover number.
Continued
297
TOC
Index
Home
2013 CR-Z 13 CR-Z-31SZT6200.book 298 ページ ２０１２年１０月２５日 木曜日 午後９時９分
uuFusesuFuse Locations
■ Interior Fuse Box Located under the driver side dashboard.
Cover
Fuse Box
Fuse Label
Fuse locations are shown on the label on the back side of the cover.
Locate the fuse in question by the fuse number and label number.
* Not available on all models
QRG
TOC
Index
Home
298
■ Circuit protected and fuse rating
Circuit Protected
Amps 15 A 7.5 A 20 A
−
−
SRS
SRS
Fog Light*
Back-Up Light
Back UP TPMS*1
Transmission SOL*2
Driver’s Power Window
10 A 10 A 10 A 7.5 A 20 A 10
7.5 A 11
7.5 A 12
10 A 13
20 A 14
7.5 A 15
7.5 A 16
10 A 17 Passenger’s Power Window 20 A 18
19
20Accessory Power Socket
Daytime Running Lights
Rear Wiper
Fuel Pump
ABS/VSA®
Radio
15 A
IMA
A/C
− −
− −
Amps 15 A 7.5 A 10 A 10 A 20 A 10 A 20 A 20 A 10 A 30 A 7.5 A 10 A 15 A 15 A 10 A 10 A 7.5 A 10 A 30 A
−
Circuit Protected
Washer Meter Hazard Stop/Horn
Audio AMP *
LAF
Door Lock Main Headlight Main
Small Light
Main Fan Motor
IGPS
Right Headlight Low*3
Right Headlight Low (HID)*4
Ignition Coil
Left Headlight Low*3
Left Headlight High*4Door Lock Door Lock
ABS FSR/VSA® FSR
−
21
22
23
24
25
26
27
28
29
30
3132
33
34
35
36
37
38*1:U.S. models only *2:Automatic transmission (CVT) *3:Vehicle with halogen bulb low beam
headlights
*4:Vehicle with discharge headlights
2013 CR-Z 13 CR-Z-31SZT6200.book 299 ページ ２０１２年１０月２５日 木曜日 午後９時９分
uuFusesuFuse Locations
QRG
■ Circuit protected and fuse rating
Amps 10 A 30 A 30 A 30 A 40 A*3
30 A*4
50 A− −
Circuit Protected
Heated Mirror *
Front Wiper Blower Motor ABS/VSA® MTR
Rear Defogger
IG Main
− −
55
56
57
5859
60
61
62*1:Vehicle with halogen bulb low beam
headlights
*2:Vehicle with discharge headlights *3:With heated door mirror *4:Without heated door mirror
Circuit Protected
IGP
Heated Seat *
−*1
Daytime Running Lights*2
IMA 1
MG Clutch
STS
Door Lock
−
Sub Fan Motor
Left Headlight High*1
Left Headlight Low (HID)*2
Door Lock Motor 2
(UNLOCK)
−
Right Headlight High
DBW IMA 2
−
39
4041
42
43
44
45
46
4748
49
50
51
52
53
54Amps 15 A 10 A
−
7.5 A 7.5 A 7.5 A 7.5 A 20 A
−
30 A 10 A 15 A
7.5 A
−
10 A 15 A 15 A
−
TOC
Index
Home
* Not available on all models
299
2013 CR-Z 13 CR-Z-31SZT6200.book 300 ページ ２０１２年１０月２５日 木曜日 午後９時９分
uuFusesuInspecting and Changing Fuses
QRG
Inspecting and Changing Fuses
Fuse
Fuse Puller
1. Turn the ignition switch to LOCK (0. Turn
1Inspecting and Changing Fuses
headlights and all accessories off.
2. Check the fuses in the engine
compartment. u If the fuse is blown, have it replaced by a
Blown Fuse
dealer.
3 . Inspect the sm all fuses in the
vehicle interior. u If there is a burned out fuse, remove it
with the fuse puller and replace it with a new one.
NOTICE Replacing a fuse with one that has a higher rating greatly increases the chances of damaging the electrical system.
Replace fuse with a spare fuse of the same specified amperage. Confirm the specified amperage using the charts on P. 297 to P. 298.
There is a fuse puller on the fuse box.
TOC
Index
Home
300
2013 CR-Z 13 CR-Z-31SZT6200.book 301 ページ ２０１２年１０月２５日 木曜日 午後９時９分
Emergency Towing
Call a professional towing service if you need to tow your vehicle.
1Emergency Towing
■ Flat bed equipment The operator loads your vehicle on the back of a truck. This is the best way to transport your vehicle.
■ Wheel lift equipment The tow truck uses two pivoting arms that go under the front tires and lift them off the ground. The rear tires remain on the ground. This is an acceptable way to tow your vehicle.
NOTICE Trying to lift or tow your vehicle by the bumpers will cause serious damage. The bumpers are not designed to support the vehicle's weight.
NOTICE Improper towing such as towing behind a motorhome or other motor vehicle can damage the transmission.
Never tow your vehicle with just a rope or chain. It is very dangerous, since ropes or chains may shift from side to side or break.
QRG
TOC
Index
Home
Continued
301
2013 CR-Z 13 CR-Z-31SZT6200.book 302 ページ ２０１２年１０月２５日 木曜日 午後９時９分
uuEmergency Towingu
■ Towing Hook For very short distances, such as freeing the vehicle, you can use the detachable towing hook that mounts on the anchor in the front bumper.
Cover
1. Push the right edge of the cover with your
finger, then remove it.
2. Take the towing hook and the wheel nut
wrench out of the cargo area.
1Towing Hook
NOTICE To avoid damage to your vehicle, use the towing hook for straight, flat ground towing only. Do not tow at an angle. This hook should not be used to tow the vehicle onto a flat bed. Do not use it as a tie down.
Make sure to use the properly-designed and attached towing equipment.
NOTICE Do not slip the clutch for a long time to get unstuck. This may overheat and damage the transmission.
Wheel Nut Wrench
3. Screw the towing hook into the hole, and
tighten it with the wheel nut wrench.
Towing Hook
QRG
TOC
Index
Home
302
2013 CR-Z 13 CR-Z-31SZT6200.book 303 ページ ２０１２年１０月２５日 木曜日 午後９時９分
When You Cannot Open the Hatch
■ What to Do When Unable to Open the Hatch If you cannot open the hatch, use the following procedure.
1. Remove the cover on the back of the hatch
by prying it off with a small flat-tip screwdriver. uWrap the flat-tip screwdriver with a cloth
to prevent scratches.
1What to Do When Unable to Open the Hatch
After taking these steps, contact a dealer to have the vehicle checked.
When you open the hatch from inside, make sure there is enough space around the hatch, and it does not hit anyone or any object.
Unlock (Open)
2. Push the release lever until the hatch unlocks. Push the hatch up to open.
QRG
TOC
Index
Home
303
2013 CR-Z 13 CR-Z-31SZT6200.book 304 ページ ２０１２年１０月２５日 木曜日 午後９時９分
QRG
Index
Home
304
2013 CR-Z 13 CR-Z-31SZT6200.book 305 ページ ２０１２年１０月２５日 木曜日 午後９時９分
QRG
Index
Home
Information
This chapter includes your vehicle's specifications, locations of identification numbers, and other information required by regulation.
Specifications .................................... 306
Identification NumbersVehicle Identification Number (VIN).. 308
Engine Number and Transmission Number...................................... 308
Devices that Emit Radio Waves ....... 309
Reporting Safety Defects ................. 310Emissions Testing
Testing of Readiness Codes.............. 311
Warranty Coverages ........................ 313
Authorized Manuals......................... 315
Customer Service Information......... 316305
2013 CR-Z 13 CR-Z-31SZT6200.book 306 ページ ２０１２年１０月２５日 木曜日 午後９時９分
Specifications
QRG
■ Engine Specifications Displacement
Spark Plugs
91 cu-in (1,497 cm3) NGK DENSO
DIFR6D13
DK20PR-D13■ Fuel Fuel: Type Fuel Tank Capacity ■ 12 Volt Battery
Unleaded gasoline, Pump octane number of 87 or higher 10.6 US gal (40 L)
Capacity/Type
■ Washer Fluid
Tank Capacity
32AH(5)/40AH(20) 34AH(5)/40AH(20)
U.S.: 2.6 US qt (2.5 L) Canada: 5.12 US qt (4.85 L)
■ Light Bulbs
Headlights (Low Beam)
Headlights (High Beam) Fog Lights * Front Turn Signal/Parking/Side Marker Lights Rear Side Marker Lights Brake/Taillights Side Turn Signal Lights (on Door Mirrors) Back-Up Lights Rear Turn Signal Lights High-Mount Brake Lights License Plate Light Cargo Area Light Interior Lights
35W (D4S)*1
55W (H11)*2
60W (HB3) 35W (H8)28W/8W
3CP LED
LED
16W 21W (Amber) LED 5W 5W
8W 3.4W
Front Rear Vanity Mirror Lights * 2W Glove Box Light Courtesy Lights
1.4W 2CP (3.8W)
*1: Vehicle with discharge headlights *2: Vehicle with halogen bulb low beam headlights
CR-Z
■ Vehicle Specifications Model No. of Passengers: Front Rear Total Weights: Gross Vehicle Weight Rating Gross Axle Weight Rating (Front)
U.S.: 3,263 lbs (1,480 kg) Canada: 1,480 kg
U.S.: 1,819 lbs (825 kg) Canada: 825 kg
Gross Axle Weight Rating (Rear)
Air Conditioning: Refrigerant Type Charge Quantity Lubricant Type
U.S.: 1,455 lbs (660 kg) Canada: 660 kg
HFC-134a (R-134a) 15.8 – 17.6 oz (450 – 500 g) SP-10
TOC
Index
Home
306
* Not available on all models
2013 CR-Z 13 CR-Z-31SZT6200.book 307 ページ ２０１２年１０月２５日 木曜日 午後９時９分
■ Engine Oil
Capacity
Recommended
3.6 US qt (3.4 L)
·Genuine Honda Motor Oil 0W-20
·API Premium-grade 0W-20 detergent oil Change Change including filter ■ Engine Coolant Specified Ratio3.8 US qt (3.6 L)
Honda Long-Life Antifreeze/Coolant Type2
50/50 with distilled water 1.17 US gal (4.42 L)*1
1.15 US gal (4.35 L)*2
(change including the remaining 0.116 US gal (0.44 L) in the reserve tank)Capacity
*1: Manual transmission models *2: Automatic transmission (CVT) models
uuSpecificationsu
P195/55R16 86V 205/45R17 84W*3
30 psi (210 kPa [2.1 kgf/cm2]) 32 psi (220 kPa [2.2 kgf/cm2])*4
30 psi (210 kPa [2.1 kgf/cm2]) 30 psi (210 kPa [2.1 kgf/cm2])*4
T135/80D15 99M 60 psi (420 kPa [4.2 kgf/cm2]) 16 x 6J 17 x 6.5J*315 x 4T
■ Tire
Size
Regular
Pressure
Front
Rear
Compact Spare *
Wheel Size
Size
Pressure
Regular
Compact Spare *
*3: Optional on Canadian models *4: 205/45R17 tires
QRG
■ Brake Fluid Honda Heavy Duty Brake Fluid DOT 3
Specified ■ Automatic Transmission (CVT) FluidSpecified
Honda CVTF (continuously variable transmission fluid) Change
Capacity ■ Manual Transmission Fluid
3.0 US qt (2.8 L)
Specified
Capacity
Honda Manual Transmission Fluid Change
1.5 US qt (1.4 L)
TOC
Index
Home
* Not available on all models
