Download PDF Manual

Seat-back Adjustment Lever


To access the rear cargo console, open the door, slide the seat by pulling up on the bar, then pull up on the seat-back adjustment lever.


Bar


Release Handle


Separator


■ Separator Folding down the separator will create more cargo area.


1. Remove any items from the rear trays. 2. Pull up the release handle on the top of the


separator.


128


1Rear Cargo Console


3WARNING


This vehicle is not equipped with rear seats or seatbelts.


Sitting in this area may result in injury or death, and may violate state laws.


Only the driver and one front seat passenger may be safely seated in this vehicle.


Make sure all items on the rear trays are secured. They could be thrown around and cause injury during a crash.


To return the separator upright, push it backwards until it locks.


Make sure that the folded separator does not press against the passenger seat, as this could cause the weight sensors to work improperly.


2 Side Airbag Off Indicator P. 50


Make sure all items in the cargo area are secured. Loose items can fly forward if you have to brake hard.


12 CR-Z-31SZT610.book 129 ページ 2011年8月29日 月曜日 午後8時8分


uuInterior Lights/Interior Convenience ItemsuInterior Convenience Items


The tonneau cover can be used to conceal your parcels and protect them from direct sunlight.


■ To extend: Pull the handle on the center edge, then clip the mounting rods in the hooks on both sides of the hatch opening.


■ To retract: Slip the rods out of the hooks, then slowly roll it back until it is completely retracted.


1Tonneau Cover


Do not access parcels in the cargo area while driving. This may cause injury if you have to brake hard.


Do not stack objects higher than the top of the seat in the cargo area. They could block your view and be thrown about the vehicle during a sudden stop.


To prevent tonneau cover damage: • Do not place items on the tonneau cover. • Do not put weight on the tonneau cover.


■ Tonneau Cover


Handle


Mounting Rod


Hook


■ To remove: Push either end of the housing inward, then lift it out of its position.


Continued


129


12 CR-Z-31SZT610.book 130 ページ 2011年8月29日 月曜日 午後8時8分


uuInterior Lights/Interior Convenience ItemsuInterior Convenience Items


■ To store: The housing unit can be stored on the cargo area floor to make more space available.


Push one end of the unit into the hole on one side panel, then insert the other end into the hole on the other side.


After storing the unit, rock it up and down to make sure it is securely placed.


Reverse this procedure to install the housing unit in place.


■ To separate the cargo area into two: 1. Pull out the tonneau cover from its housing


while it is stored on the cargo area floor.


2. Clip the mounting rods in the hooks at both


sides of the hatch opening.


130


12 CR-Z-31SZT610.book 131 ページ 2011年8月29日 月曜日 午後8時8分


uuInterior Lights/Interior Convenience ItemsuInterior Convenience Items


■ Seat Heaters*


The ignition switch must be in ON (w to use the seat heaters. The HI setting heats the seats faster than the LO setting.


There is no heater in the passenger's seat- back due to the side airbag cutoff system.


While in HI, the heater cycles on and off. uThe appropriate indicator will be on


while the seat heater is on. Briefly press the switch on the opposite side to turn the heater off. The indicator will be off. When a comfortable temperature is reached, select LO to keep the seat warm.


Seat Heater Switch


1Seat Heaters*


3WARNING


Heat induced burns are possible when using seat heaters.


Persons with a diminished ability to sense temperature (e.g., persons with diabetes, lower-limb nerve damage, or paralysis) or with sensitive skin should not use seat heaters.


Do not use the seat heaters even in LO when the engine is off. Under such conditions, the battery may be weakened, making the engine difficult to start.


In the LO setting, the heater runs continuously and does not automatically turn off.


* Not available on all models


131


12 CR-Z-31SZT610.book 132 ページ 2011年8月29日 月曜日 午後8時8分


Climate Control System


Using Automatic Climate Control The automatic climate control system maintains the interior temperature you select. The system also selects the proper mix of heated or cooled air that will as quickly as possible, raise or lower the interior temperature to your preference.


(Windshield Defogger) Button


MODE Button


A/C (Air Conditioning) Button AUTO Button


Temperature Control Dial


(ON/OFF) Button


Floor and defroster vents


Floor vents


Dashboard and floor vents Dashboard vents


(Fan Control) Button


(Recirculation) Button


Use the system when the engine is running. 1. Press the AUTO button. 2. Adjust the interior temperature using the temperature control dial. 3. Press the


button to cancel.


■ Switching between the recirculation and fresh air modes Press the button and switch the mode depending on environmental conditions. Recirculation Mode (indicator on): Recirculates air from the vehicle’s interior through the system. Fresh Air Mode (indicator off): Maintains outside ventilation. Keep the system in fresh air mode in normal situations.


132


1Using Automatic Climate Control


If any buttons are pressed while using the climate control system in AUTO, the function of the button that was pressed will take priority. The AUTO indicator will go off, but functions unrelated to the button that was pressed will be controlled automatically.


During the Auto Idle Stop, the air conditioning system will be turned off. If the ECON mode is selected, the fan may also be turned off. To prevent cold air from blowing in from outside, the fan may not start immediately when the AUTO button is pressed.


Once you have set the desired temperature, do not use the temperature control dial more than necessary. Doing so may delay the time it takes to reach the set temperature. If the interior is very warm, you can cool it down more rapidly by partially opening the windows, turning the system on AUTO, and setting the temperature to low. Change the fresh air mode to recirculation mode until the temperature cools down.


When you set the temperature to the lower or upper limit, Lo or Hi is displayed.


Pressing the control system between on and off. When turned on, the system returns to your last selection.


button switches the climate


12 CR-Z-31SZT610.book 133 ページ 2011年8月29日 月曜日 午後8時8分


uuClimate Control SystemuUsing Automatic Climate Control


■ Defrosting the Windshield and Windows


button turns the air


Pressing the conditioning system on and automatically switches the system to fresh air mode.


Press the system returns to the previous settings.


button again to turn off, the


■ To rapidly defrost the windows


1. Press the 2. Press the


button.


button (the indicator on).


1Defrosting the Windshield and Windows


For your safety, make sure you have a clear view through all the windows before driving.


Do not set the temperature near the upper or lower limit. When cold air hits the windshield, the outside of the windshield may fog up.


If the side windows fog up, adjust the vents so that the air hits the side windows.


1To rapidly defrost the windows


After defrosting the windows, switch over to fresh air mode. If you keep the system in recirculation mode, the windows may fog up from humidity. This impedes visibility.


Automatic transmission (CVT) models Pressing the automatically during the auto idle stop.


button restarts the engine


Manual transmission models To defog during the auto idle stop, restart the engine as follows. 1. Make sure the shift lever is in (N. 2. Depress the clutch pedal fully. 3. Press the


button.


133


12 CR-Z-31SZT610.book 134 ページ 2011年8月29日 月曜日 午後8時8分


uuClimate Control SystemuAutomatic Climate Control Sensors


Automatic Climate Control Sensors


Sunlight Sensor


The automatic climate control system is equipped with a sunlight sensor, an interior temperature and humidity sensor. Do not cover or spill any liquid on them.


Temperature and Humidity Sensor


134


12 CR-Z-31SZT610.book 135 ページ 2011年8月29日 月曜日 午後8時8分


This chapter describes how to operate the audio system and other technology features.


Features


Audio System


About Your Audio System................ 136
USB Adapter Cable .......................... 137
Auxiliary Input Jack .......................... 138
Audio System Theft Protection ......... 139
Audio Remote Controls.................... 140


Audio without Navigation System


Audio System Basic Operation.......... 141
Playing the AM/FM Radio................. 143
Playing a CD .................................... 145
Playing an iPod®............................... 147
Playing a USB Flash Drive ................. 149


Audio with Navigation System *


Audio System Basic Operation.......... 151
Playing the AM/FM Radio................. 154
Playing a CD .................................... 156
Playing a PC Card ............................ 158
Playing an iPod®............................... 162
Playing a USB Flash Drive ................. 165


Audio Error Messages


CD Player......................................... 167
iPod®/USB Flash Drive....................... 168


General Information on the Audio System Recommended CDs ......................... 169
Compatible iPod® and USB Flash Drives...171
Recommended PC Card................... 172


Bluetooth® HandsFreeLink®


Using HFL ........................................ 173
HFL Menus ...................................... 175


* Not available on all models


135


12 CR-Z-31SZT610.book 136 ページ 2011年8月29日 月曜日 午後8時8分


Audio System


About Your Audio System The audio system features AM/FM radio. It can also play audio CDs, WMA/MP3/AAC files, iPods®, and USB flash drives.


You can operate the audio system from the buttons and switches on the panel or the remote controls on the steering wheel, or icons on the navigation screen.


USB Adapter Cable


iPod®


USB Flash Drive


Models with navigation system


Auxiliary Input Jack


Models without navigation system


Remote Control


Auxiliary Input Jack


136


1About Your Audio System


Video CDs, DVDs, and 3-inch (8-cm) mini CDs are not supported.


iPod® is a registered trademark owned by Apple Inc.


MP3 and AAC are standard audio compression formats. WMA is an audio compression format developed by Microsoft Corporation.


Models with navigation system You can operate the audio system by voice commands. See the navigation system manual for full details.


12 CR-Z-31SZT610.book 137 ページ 2011年8月29日 月曜日 午後8時8分


USB Adapter Cable


USB Adapter Cable


1. Pull up the center pocket lid. 2. Unclip the USB connector and loosen the adapter cable. 3. Install the iPod® dock connector or the USB flash drive to the USB connector.


uuAudio SystemuUSB Adapter Cable


1USB Adapter Cable


• Do not leave the iPod® or USB flash drive in the


vehicle. Direct sunlight and high temperatures may damage it.


• Do not use an extension cable with the USB


adapter cable.


• Do not connect the iPod® or USB flash drive using a


hub.


• Do not use a device such as a card reader or hard


disk drive, as the device or your files may be damaged.


• We recommend backing up your data before using


the device in your vehicle.


• Displayed messages may vary depending on the


device model and software version.


If the audio system does not recognize the iPod®, try reconnecting it a few times or reboot the device. To reboot, follow the manufacturer's instructions provided with the iPod® or visit www.apple.com/ ipod.


137


1Auxiliary Input Jack


To switch the mode, press any of the audio mode buttons. You can return to the AUX mode by pressing the AUX button.


Models with navigation system Press either the AM/FM button or the CD/AUX button, or touch the icon to switch the mode.


You cannot use the auxiliary input jack if you replace the audio system.


State or local laws may limit the circumstances in which you can launch or control your attached audio device.


12 CR-Z-31SZT610.book 138 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio SystemuAuxiliary Input Jack


Auxiliary Input Jack Use the jack to connect standard audio devices.


Models without navigation system


Cover


1. Open the AUX cover. 2. Connect a standard audio device to the


input jack using a 1/8 inch (3.5 mm) stereo miniplug. u The audio system automatically switches


to the AUX mode.


Models with navigation system


Cover


138


12 CR-Z-31SZT610.book 139 ページ 2011年8月29日 月曜日 午後8時8分


Audio System Theft Protection The audio system is disabled when it is disconnected from the power source, such as when the 12 volt battery is disconnected or goes dead.


■ Reactivating the audio system 1. Turn the ignition switch to ON (w, and turn on the audio system.


u If you turn the ignition switch to ACCESSORY (q, you will be requested to


2.


enter the audio security code. Models without navigation system Enter the audio security code using the preset buttons. Models with navigation system Touch the icon to enter the code, then touch the Done icon to set it.


If you enter an incorrect digit, continue to the last digit, then try again. If you do not enter the code correctly after 10 tries, leave the system for one hour before trying again, or visit a dealer to have the system reset.


uuAudio SystemuAudio System Theft Protection


1Audio System Theft Protection


Find the audio system's security code and serial number label in your owner’s manual kit.


We recommend that you write down the serial number in this owner’s manual.


Do not store the label in your vehicle. If you lose the label, you must first retrieve the serial number, and then obtain the code.


You can find out about your serial number and security code from a dealer.


U.S. models You can register the security code at Owner Link (owners.honda.com.), and find information on how to retrieve the serial number and obtain the code at radio-navicode.honda.com.


139


12 CR-Z-31SZT610.book 140 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio SystemuAudio Remote Controls


Audio Remote Controls Allows you to operate the audio system while driving. MODE Button Cycles through the audio modes as follows: Models without navigation system FM1 FM2 AM CD AUX


MODE Button


CH (Channel) Button


VOL (Volume) Button


Models with navigation system FM1 FM2 AM CD PC Card AUX


1Audio Remote Controls


When in the AUX mode, the following is operable from the remote controls: • iPod®/USB flash drive connected to the USB


adapter cable


VOL Button Press Press


: Increases the volume. : Decreases the volume.


CH Button • When listening to the radio


Press (+ : Selects the next preset radio station. Press (- : Selects the previous preset radio station. Press and hold (+ : Selects the next strong station. Press and hold (- : Selects the previous strong station.


• When listening to a CD, iPod® or USB flash drive, or PC Card


Press (+ : Skips to the next song. Press (- : Goes back to the beginning of the current or previous song.


• When listening to a CD or USB flash drive


Press and hold (+ : Skips to the next folder. Press and hold (- : Goes back to the previous folder.


140


12 CR-Z-31SZT610.book 141 ページ 2011年8月29日 月曜日 午後8時8分


Audio without Navigation System


Audio System Basic Operation To use the audio system function, the ignition switch must be in ACCESSORY (q or ON (w.


Button


Use the selector knob to access some audio functions.


Selector knob: Rotate left or right to scroll through the available choices. Press to set your selection.


button: Press to select the Sound


Setting mode.


button: Press to go back to the


previous display.


Selector Knob


1Audio System Basic Operation


These indications are used to show how to operate the selector knob. Rotate Press


to ENTER.


to select.


Press the MODE, (+, (-, steering wheel to change any audio setting.


3 4


or


button on the


2 Audio Remote Controls P. 140


Continued


141


12 CR-Z-31SZT610.book 142 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio without Navigation SystemuAudio System Basic Operation


■ Adjusting the Sound


Selector Knob


Press the adjust the setting.


button, and rotate


to


Each time you press the mode switches as follows.


button, a sound


1Adjusting the Sound


When the adjustment level reaches the center, you will see "C" in the display.


The SVC has four modes: OFF, LOW, MID, and HIGH. SVC adjusts the volume level based on the vehicle speed. As you go faster, audio volume increases. As you slow down, audio volume decreases.


(Sound) Button


142


* Not available on all models


Subwoofer *


Speed-sensitive Volume Compensation


12 CR-Z-31SZT610.book 143 ページ 2011年8月29日 月曜日 午後8時8分


Playing the AM/FM Radio


uuAudio without Navigation SystemuPlaying the AM/FM Radio


Button Press to display and select an RDS category.


FM/AM Button Press to select a band.


(Power) Button


Press to turn the audio system ON and OFF.


Selector Knob Turn to adjust the volume. Press and turn to tune the radio frequency.


SEEK Buttons


● Press to change a station. ● Press and hold to search up and


down the selected band for a station with a strong signal.


SCAN Button Press to sample each of the strongest stations on the selected band for 10 seconds. To turn off scan, press the button again.


Preset Buttons (1-6) To store a station: 1. Tune to the selected station. 2. Pick a preset button and hold it


until you hear a beep.


To listen to a stored station, select a band, then press the preset button.


TITLE Button Press to switch the RDS name on and off.


A.SEL (Auto Select) Button Press to scan both bands and store the strongest station in each preset. To turn off auto select, press the button again. This restores the presets you originally set.


Continued


143


12 CR-Z-31SZT610.book 144 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio without Navigation SystemuPlaying the AM/FM Radio


■ Auto Select (A.SEL) Use the auto select feature to scan both bands and store the strongest station in each preset.


1Playing the AM/FM Radio


The ST indicator appears on the display indicating stereo FM broadcasts. Stereo reproduction in AM is not available.


Press the A.SEL button to activate the feature.


To turn off auto select, press the A.SEL button again. This restores the presets you originally set.


■ Radio Data System (RDS) Provides text data information related to your selected RDS capable FM station.


■ RDS INFO ON Press the TITLE button while listening to an RDS capable station. “RDS INFO ON” appears, and the station name is displayed.


■ To find an RDS station from your selected program category


1. Press the


button to


display and select an RDS category.


2. Use SEEK or SCAN to select an RDS station.


Switching the Audio Mode Press the MODE button on the steering wheel.


2 Audio Remote Controls P. 140


You can store six AM stations and twelve FM stations into the preset button memory. FM1 and FM2 let you store six stations each.


Auto Select function scans and stores up to six AM stations and twelve FM stations with a strong signal into the preset button memory.


If you do not like the stations auto select has stored, you can manually store your preferred frequencies.


1Radio Data System (RDS)


The display shows up to 31 characters of text data. Press and hold the TITLE button to see additional characters. indicates that the text data continues. The display goes back to the previous screen if you press and hold the button again.


RDS Category


144


12 CR-Z-31SZT610.book 145 ページ 2011年8月29日 月曜日 午後8時8分


Playing a CD Your audio system supports audio CDs, CD-Rs and CD-RWs in either MP3 or WMA format. With the CD loaded, press the CD button.


uuAudio without Navigation SystemuPlaying a CD


Selector Knob Turn to adjust the volume. Press and turn to select an item, then press to set your selection.


(CD Eject) Button


Press to eject a CD.


(Power) Button


Press to turn the audio system ON and OFF.


Press (files in MP3 or WMA).


SEEK Buttons or


to change tracks


SCAN Button You will get a 10-second sampling of each song. ● Press to sample all tracks on the CD (all files in


the current folder in MP3 or WMA).


● Press two times to sample the first file in each


of the main folders (MP3 or WMA).


● To turn off scan, press and hold the button.


Button


Press the beginning of the previous folder in MP3 or WMA.


to skip to the next folder, and


to skip to


CD Slot Insert a CD about halfway into the CD slot.


CD Button Press to play a CD.


TITLE Button Press to display the text data on a CD (if it was recorded with text data).


RDM (Random) Button ● Press to play all tracks/files on a CD


in random order.


● Press two times to play all files in


the current folder (MP3 or WMA) in random order.


● To turn off random, press and hold


the button.


RPT (Repeat) Button ● Press to replay a track/file continuously. ● Press two times to replay all files in the current folder. ● To turn off repeat, press and hold the button.


Continued


145


12 CR-Z-31SZT610.book 146 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio without Navigation SystemuPlaying a CD


■ How to Select a File from a Folder with the Selector Knob


(MP3/WMA)


1. Press 2. Rotate uPress


to switch the display to a folder list.


to select a folder.


button to play the first file on the selected folder.


3. Press 4. Rotate


to change the display to a list of files in that folder.


to select a file, then press


146


1Playing a CD


NOTICE Do not use CDs with adhesive labels. The label can cause the CD to jam in the unit.


WMA files protected by digital rights management (DRM) cannot be played. The audio system displays “UNSUPPORTED,” then skips to the next file.


Text data appears on the display under the following circumstances: • When you select a new folder, file, or track. • When you change the audio mode to CD. • When you insert a CD.


The display shows up to 31 characters of text data. Press and hold the TITLE button to see additional characters. indicates that the text data continues. The display goes back to the previous screen if you press and hold the button again.


If you eject the CD but do not remove it from the slot, the system reloads the CD automatically after several seconds.


12 CR-Z-31SZT610.book 147 ページ 2011年8月29日 月曜日 午後8時8分


Playing an iPod® Connect the iPod® using your dock connector to the USB adapter cable, then press the AUX button.


2 USB Adapter Cable P. 137


uuAudio without Navigation SystemuPlaying an iPod®


Button


Press previous display.


to go back to the


Selector Knob Turn to adjust the volume. Press and turn to select an item, then press to set your selection.


(Power) Button


Press to turn the audio system ON and OFF.


Press


SEEK Buttons or


to change songs.


Button


Press to set your selection.


USB Indicator Comes on when an iPod® is connected.


AUX Button Press to select iPod® (if connected).


TITLE Button Press to display the text data.


RDM (Random) Button ● Press to play all available files in a


selected list (playlists, artists, albums or songs) in random order.


● Press two times to play all available


albums in a selected list (playlists, artists, albums or songs) in random order.


● To turn off shuffle mode, press and


hold the button.


Continued


147


RPT (Repeat) Button ● Press to replay a file continuously. ● To turn off repeat, press the button


again.


12 CR-Z-31SZT610.book 148 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio without Navigation SystemuPlaying an iPod®


to display the iPod® menu.


■ How to Select a File from the iPod® Menu 1. Press 2. Rotate 3. Press 4. Rotate


to display the items on that menu.


to select an item, then press


to select a menu.


1Playing an iPod®


Available operating functions vary on models or versions. Some functions may not be available on the vehicle's audio system.


If there is a problem, you may see an error message on the display.


2 iPod®/USB Flash Drive P. 168


148


12 CR-Z-31SZT610.book 149 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio without Navigation SystemuPlaying a USB Flash Drive


Playing a USB Flash Drive Your audio system reads and plays sound files on a USB flash drive in either MP3, WMA or AAC*1 format. Connect your USB flash drive to the USB adapter cable, then press the AUX button.


2 USB Adapter Cable P. 137


Button


Press


to skip to the next folder, and


to skip to the beginning of the


previous folder.


USB Indicator Comes on when a USB flash drive is connected.


Selector Knob Turn to adjust the volume. Press and turn to select an item, then press to set your selection.


(Power) Button


Press to turn the audio system ON and OFF.


Press


SEEK Buttons or


to change files.


SCAN Button You will get a 10-second sampling of each file. ● Press to sample all files in the current folder. ● Press two times to sample the first file in each of


the main folders.


● To turn off scan, press and hold the button.


*1:Only AAC format files recorded with iTunes® are playable on this unit.


AUX Button Press to select USB flash drive (if connected).


TITLE Button Press to display the text data.


RDM (Random) Button ● Press to play all files in random order. ● Press two times to play all files in the


current folder in random order.


● To turn off random, press and hold


the button.


RPT (Repeat) Button ● Press to replay a file continuously. ● Press two times to replay all files in the current folder. ● To turn off repeat, press and hold the button.


Continued


149


1Playing a USB Flash Drive


Use the recommended USB flash drives.


2 USB Flash Drives P. 171


Files in WMA format protected by digital rights management (DRM) are not played. The audio system displays “UNPLAYABLE FILE,” and then skips to the next file.


If there is a problem, you may see an error message on the display.


2 iPod®/USB Flash Drive P. 168


12 CR-Z-31SZT610.book 150 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio without Navigation SystemuPlaying a USB Flash Drive


■ How to Select a File from a Folder with the Selector Knob 1. Press 2. Rotate uPress


button to play the first file on the selected folder.


to switch the display to a folder list.


to select a folder.


3. Press 4. Rotate


to change the display to a list of files in that folder.


to select a file, then press


150


12 CR-Z-31SZT610.book 151 ページ 2011年8月29日 月曜日 午後8時8分


Audio with Navigation System *


Audio System Basic Operation To use the audio system function, the ignition switch must be in ACCESSORY (q or ON (w.


■ Operation with the Control Icons To operate the audio system, press the control buttons on the side of the screen or touch the control icons on the audio screen.


Press the AUDIO button to show the audio screen.


To select any function, touch the appropriate icon on the screen.


AUDIO Button


■ How to access the disc slot or PC card slot


Press the OPEN button.


The screen folds back, and the CD and PC card slots appears.


* Not available on all models


Continued


1Audio System Basic Operation


Voice Control System The audio system is voice operable. See the navigation system manual for details.


1Operation with the Control Icons


AUDIO INFO Icon


On the navigation screen, touch the AUDIO INFO icon to see the selected audio information. Press any of the audio buttons to display the audio status bar at the bottom of the screen.


151


12 CR-Z-31SZT610.book 152 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio with Navigation System *uAudio System Basic Operation


PC Card Slot


(CD Eject) Button


Press to eject a CD.


Push the CLOSE button to return the screen to the upright position.


CD Slot


CLOSE Button


(PC Card Eject) Button


Press to eject a PC card.


■ Adjusting the sound


1Operation with the Control Icons


If you eject the CD but do not remove it from the slot, the system reloads the CD automatically after several seconds.


Do not use the folded down screen as a tray.


Press the AUDIO button, then touch the Sound icon.


1Adjusting the sound


When the adjustment level reaches the center, you will see "C" in the display.


Adjustable Settings:


Sound Mode


Sound Icon


Speaker Setting


The SVC has four modes: OFF, LOW, MID, and HIGH. SVC adjusts the volume level based on the vehicle speed. As you go faster, audio volume increases. As you slow down, audio volume decreases.


The system automatically returns to the selected audio mode several seconds after you stop adjusting a setting.


Bass/Treble Setting


Speed-sensitive Volume Compensation


To adjust each setting, touch any setting icon such as FR or RR on the fader setting.


152


12 CR-Z-31SZT610.book 153 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio with Navigation System *uAudio System Basic Operation


■ Selecting the Background There are three backgrounds to choose from when displaying sound levels: Level: The sound level is shown with the vertical bars.


Spectrum Analysis: The sound level appears as ripples of water.


Off


Each time you touch the Background icon, the screen changes.


■ Operation with the Joystick


Joystick


Use the joystick to select an icon on the screen and access some audio functions.


Push left, right, up, or down to select an item.


Press to set your selection.


153


12 CR-Z-31SZT610.book 154 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio with Navigation System *uPlaying the AM/FM Radio


Playing the AM/FM Radio


VOL/PWR (Volume/Power) Knob Press to turn the audio system ON and OFF. Turn to adjust the volume.


FM1/FM2/AM Icon Touch to select a band.


Navigation Display


Joystick


AUTO SEL (Auto Select) Button Touch to scan both bands and store the strongest station in each preset. To turn off auto select, touch it again. This restores the presets you originally set.


TUNE Bar ● Press either side to select a station. ● Press and hold to search up and down the selected band for a station with a strong signal.


Preset Buttons (1-6) To store the station: 1. Tune to the selected station. 2. Pick a preset button and hold it


until you hear a beep.


To listen to a stored station, select a band, then press the preset button.


AM/FM Button Press to select a band. AUDIO Button Press to display the audio mode on the navigation screen.


SCAN Button Press to sample each of the strongest stations on the selected band for 10 seconds. To turn off scan, press the button again.


154


12 CR-Z-31SZT610.book 155 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio with Navigation System *uPlaying the AM/FM Radio


■ Auto Select Use the auto select feature to scan both bands and store the strongest station in each preset.


1Playing the AM/FM Radio


The STEREO indicator appears on the display indicating stereo FM broadcasts. Stereo reproduction in AM is not available.


Touch AUTO SEL to activate the feature.


To turn off auto select, touch AUTO SEL again.


Switching the Audio Mode Press the MODE button on the steering wheel.


2 Audio Remote Controls P. 140


You can store six AM stations and twelve FM stations into the preset button memory. FM1 and FM2 let you store six stations each.


Auto Select function scans and stores up to six AM stations and twelve FM stations with a strong signal into the preset button memory.


If you do not like the stations auto select has stored, you can manually store your preferred frequencies.


155


12 CR-Z-31SZT610.book 156 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio with Navigation System *uPlaying a CD


Playing a CD Your audio system supports audio CDs, CD-Rs and CD-RWs in either MP3 or WMA format. With the CD loaded, press the CD/AUX button or touch the CD icon.


VOL/PWR (Volume/Power) Knob Press to turn the audio system ON and OFF. Turn to adjust the volume.


CD Icon Touch to play a CD.


Navigation Display


Joystick


CD/AUX Button Press to play a CD. AUDIO Button Press to display the audio mode on the navigation screen.


SCAN Button You will get a 10-second sampling of each song. ● Press to sample all tracks on


the CD (all files in the current folder in MP3 or WMA).


● Press two times to sample the first file in each folder on the CD (MP3 or WMA).


● To turn off scan, press and


hold the button.


156


(Rewind/Fast


Forward) Buttons Press and hold to move rapidly within a track/file.


Press to change tracks (files in MP3 or WMA).


(Skip) Buttons or


RDM (Random) Button ● Press to play all tracks/files on a CD


in random order.


● Press and hold to play all files in


the current folder (MP3 or WMA) in random order.


● To turn off random, press the


button again.


RPT (Repeat) Button ● Press to replay a track/file


continuously.


● Press and hold to replay all


files in the current folder (MP3 or WMA).


● To turn off repeat, press the


button again.


FOLDER Bar to skip to the Press next folder, and to skip to the beginning of the previous folder in MP3 or WMA.


12 CR-Z-31SZT610.book 157 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio with Navigation System *uPlaying a CD


■ How to Select a File from a List


1Playing a CD


NOTICE Do not use CDs with adhesive labels. The label can cause the CD to jam in the unit.


WMA files protected by digital rights management (DRM) cannot be played. The audio system displays FILE ERROR, then skips to the next file.


1. Touch Track List to display a folder list.


Track List Icon


Folder List


2. Touch


3 4


to scroll through the list, and


touch an icon to select a folder.


Folder Icon


3. Scroll through the list and touch an icon to


select a file. uTouch Return to go back to the previous


screen.


uTouch the folder icon on the upper left to


move to the parent folder.


Return Icon


• Any songs not in a folder will automatically be added to the “Root” folder, which


is then displayed at the top of the Folder List.


• If the root folder has some additional folders in the lower layer, they will be listed


on the screen.


• To exit the list, press the AUDIO button.


157


12 CR-Z-31SZT610.book 158 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio with Navigation System *uPlaying a PC Card


Playing a PC Card Your audio system reads and plays audio files on a PC card in either MP3 or WMA format. Insert a PC card into the PC card slot, then press the CD/AUX button, or touch the AUX icon.


2 How to access the disc slot or PC card slot P. 151


VOL/PWR (Volume/Power) Knob Press to turn the audio system ON and OFF. Turn to adjust the volume.


Navigation Display


CD/AUX Button Press to play the PC card. AUDIO Button Press to display the audio mode on the navigation screen.


SCAN Button You will get a 10-second sampling of each song. ● Press to sample all files. ● Press and hold to sample the first file in each folder/artist/ album.


● To turn off scan, press the


button.


158


AUX Icon Touch to play the PC card.


PLAY MODE Icon Touch to select any of three modes (FOLDER, ARTIST, ALBUM).


Joystick


(Rewind/Fast


Forward) Buttons Press and hold to move rapidly within a track/file.


Press files.


(Skip) Buttons or


to change


RPT (Repeat) Button ● Press to replay a file


continuously.


● Press and hold to replay all


files in the current folder.


● To turn off repeat, press the


button again.


RDM (Random) Button ● Press to play all files in the current


folder in random order.


● Press and hold to play all files in


each folder/artist/album in random order.


● To turn off random, press the


button again.


FOLDER Bar to skip to the Press next folder, and to skip to the beginning of the previous folder.


12 CR-Z-31SZT610.book 159 ページ 2011年8月29日 月曜日 午後8時8分


■ How to Select a Play Mode


PLAY MODE Icon


1. Touch PLAY MODE.


Folder mode is shown.


There are three play modes: Folder mode: Plays files in the order they are recorded to the PC card. Artist mode: Plays files in alphabetical order, by artist and song title. Album mode: Plays albums (folders) in alphabetical order.


2. Touch the play mode icon.


3. Touch either playing menu.


u Continue playing the current song goes into the selected play mode after playing the current file.


uuAudio with Navigation System *uPlaying a PC Card


1How to Select a Play Mode


Pressing the CANCEL button goes back to the previous screen. To exit the play mode screen, press the AUDIO button.


WMA format protected by digital rights management (DRM) cannot be played. The audio system skips to the next file.


If there is a problem with the PC card player, see a dealer.


Continued


159


12 CR-Z-31SZT610.book 160 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio with Navigation System *uPlaying a PC Card


■ How to Select a File from a List


1. Touch Track List.


1How to Select a File from a List


In artist mode, artist name list is shown.


Track List Icon


Folder mode is shown.


2. Touch an icon to select a file.


uTouch Return to go back to the previous


In album mode, album name list is shown.


screen.


uIn folder mode, touch the folder icon on


the upper left to move to the parent folder. uTouch


to scroll through the list.


3 4


160


12 CR-Z-31SZT610.book 161 ページ 2011年8月29日 月曜日 午後8時8分


■ Song search You can search for a file with any of three modes: Title by Keyword, Artist, and Album. 1. Touch Song Search.


uuAudio with Navigation System *uPlaying a PC Card


1Song search


• Touch Return to go back to the previous screen. • In folder mode, touch the folder icon on the upper


left to move to the parent folder.


• Touch


3 4


to scroll through the list.


Folder mode is shown.


Return Icon Song Search Icon


In Title by Keyword mode, touch the letter icons to enter the title name or any keyword. Touch List to begin the song search.


2. Touch any icon from the three song search


items.


3. Select a song from the list, then touch an


icon.


Delete icon: Touch to cancel the selected letter. More icon: Touch to show the other character list.


Press the CANCEL button to exit the song search mode.


161


12 CR-Z-31SZT610.book 162 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio with Navigation System *uPlaying an iPod®


Playing an iPod® Connect the iPod® using your dock connector to the USB adapter cable, then press the CD/AUX button or touch the USB icon.


2 USB Adapter Cable P. 137


VOL/PWR (Volume/Power) Knob Press to turn the audio system ON and OFF. Turn to adjust the volume.


CD/AUX Button Press to play an iPod®. AUDIO Button Press to display the audio mode on the navigation screen. The display shows the current file number and total of playable files.


USB Icon Touch to play an iPod®.


Navigation Display


Joystick


(Rewind/Fast


Forward) Buttons Press and hold to move rapidly within a track/file.


Press files.


(Skip) Buttons or


to change


RPT (Repeat) Button ● Press to replay a file continuously. ● To turn off repeat, press the


button again.


RDM (Random) Button ● Press to play all available files in a selected list


(playlists, artists, albums or songs) in random order.


● Press and hold to play all available albums in a


selected list (playlists, artists, albums or songs) in random order.


● To turn off shuffle mode, press the button again.


162


12 CR-Z-31SZT610.book 163 ページ 2011年8月29日 月曜日 午後8時8分


■ How to Select a File from the iPod Menu 1. Touch iPod MENU.


iPod MENU Icon


2. Touch any of the mode icons (Playlists,


Artists, Albums, and Songs).


uuAudio with Navigation System *uPlaying an iPod®


1Playing an iPod®


Available operating functions vary on models or versions. Some functions may not be available on the vehicle’s audio system.


If there is a problem, you may see an error message on the display.


2 iPod®/USB Flash Drive P. 168


Voice Control System You can select the AUX mode by using the navigation system voice control buttons, but you cannot operate the play mode functions by voice.


Pressing the CANCEL button goes back to the previous screen. To exit the play mode screen, press the AUDIO button.


3. Touch an item on the displayed list.


uTouch Return to go back to the previous


screen. uTouch


3 4


to scroll through the list.


Continued


163


12 CR-Z-31SZT610.book 164 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio with Navigation System *uPlaying an iPod®


■ How to Select a File from a Track List


1. Touch Track List.


2. Touch an item on the displayed list.


uTouch Return to go back to the previous


screen. uTouch


3 4


to scroll through the list.


Track List Icon


164


12 CR-Z-31SZT610.book 165 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio with Navigation System *uPlaying a USB Flash Drive


Playing a USB Flash Drive Your audio system reads and plays sound files on a USB flash drive in either MP3, WMA or AAC*1 format. Connect your USB flash drive to the USB adapter cable, then press the CD/AUX button or touch the USB icon. 2 USB Adapter Cable P. 137


VOL/PWR (Volume/Power) Knob Press to turn the audio system ON and OFF. Turn to adjust the volume.


Navigation Display


CD/AUX Button Press to play a USB flash drive. AUDIO Button Press to display the audio mode on the navigation screen.


SCAN Button You will get a 10-second sampling of each song. ● Press to sample all files in the


current folder.


● Press to sample the first file in


main folder.


● To turn off scan, press the


button again.


USB Icon Touch to play a USB flash drive.


Joystick


(Rewind/Fast


Forward) Buttons Press and hold to move rapidly within a track/file.


Press files.


(Skip) Buttons or


to change


RDM (Random) Button ● Press to play all files in random order. ● Press and hold to play all files in the


current folder in random order.


● To turn off random, press the button


again.


RPT (Repeat) Button ● Press to replay a file


continuously.


● Press and hold to replay all


files in the current folder.


● To turn off repeat, press the


button again.


FOLDER Bar to skip to the Press next folder, and to skip to the beginning of the previous folder.


*1: Only AAC format files recorded with iTunes® are playable on this unit.


Continued


165


1Playing a USB Flash Drive


Use the recommended USB flash memory devices.


2 USB Flash Drives P. 171


Files in WMA format protected by digital rights management (DRM) are not played. The audio system displays UNPLAYABLE FILE, and then skips to the next file.


If there is a problem, you may see an error message on the display.


2 iPod®/USB Flash Drive P. 168


12 CR-Z-31SZT610.book 166 ページ 2011年8月29日 月曜日 午後8時8分


uuAudio with Navigation System *uPlaying a USB Flash Drive


■ How to Select a File from a List


1. Touch Track List.


Track List Icon


Folder List


2. Touch


3 4


to scroll through the list, and


touch an icon to select a folder.

Loading...
x