of the wheel diagonal to the flat tire.
The tire to be replaced.
Wheel Blocks
QRG
TOC
Index
Home
306
13 CIVIC HYBRID-31TR26100.book 307 ページ 2012年12月18日 火曜日 午後2時59分
uuIf a Tire Goes FlatuChanging a Flat Tire
Jack Handle Bar
5. Place the compact spare tire (wheel side up)
under the vehicle body, near the tire that needs to be replaced.
6. Remove the center cap from the wheel with
the jack handle bar. u Wrap the jack handle bar with a cloth to
prevent scratches.
7. Loosen each wheel nut about one turn
using the wheel nut wrench.
Continued
QRG
TOC
Index
Home
307
13 CIVIC HYBRID-31TR26100.book 308 ページ 2012年12月18日 火曜日 午後2時59分
uuIf a Tire Goes FlatuChanging a Flat Tire
■ How to Set Up the Jack
1. Place the jack under the jacking point
closest to the tire to be changed.
2. Turn the end bracket (as shown in the
image) clockwise until the top of the jack contacts the jacking point. u Make sure that the jacking point tab is
resting in the jack notch.
3. Raise the vehicle, using the jack handle bar and the jack handle, until the tire is off the ground.
Jack Handle Bar
Wheel Nut Wrench as Jack Handle
QRG
TOC
Index
Home
308
1How to Set Up the Jack
3WARNING
The vehicle can easily roll off the jack, seriously injuring anyone underneath.
Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.
Do not use the jack with people or luggage in the vehicle.
Use the jack provided in your vehicle. Other jacks may not support the weight (“load”) or their shape may not match.
The following instructions must be followed to use the jack safely. • Do not use while the engine is running. • Use only where the ground is firm and level. • Use only at the jacking points. • Do not get in the vehicle while using the jack. • Do not put anything on top of or underneath the
jack.
13 CIVIC HYBRID-31TR26100.book 309 ページ 2012年12月18日 火曜日 午後2時59分
uuIf a Tire Goes FlatuChanging a Flat Tire
■ Replacing the Flat Tire
1. Remove the wheel nuts and flat tire.
1Replacing the Flat Tire
Do not over tighten the wheel nuts by applying extra torque using your foot or a pipe.
2. Wipe the mounting surfaces of the wheel
with a clean cloth.
3. Mount the compact spare tire.
4. Screw the wheel nuts until they touch
the lips around the mounting holes, and stop rotating.
5. Lower the vehicle and remove the jack.
Tighten the wheel nuts in the order indicated in the image. Go around, tightening the nuts, two to three times in this order.
Wheel nut torque: 80 lbf∙ft (108 N∙m, 11 kgf∙m)
Continued
QRG
TOC
Index
Home
309
13 CIVIC HYBRID-31TR26100.book 310 ページ 2012年12月18日 火曜日 午後2時59分
uuIf a Tire Goes FlatuChanging a Flat Tire
■ Storing the Flat Tire
For normal tire
Wing Bolt
Spacer Cone
For compact spare tire
1. Remove the center cap.
2. Place the flat tire face down in the compact
spare tire well.
3. Remove the spacer cone from the wing
bolt, flip it over, and insert it back on the bolt. Secure the flat tire with the wing bolt.
4. Securely put the jack and wheel nut wrench
back in the tool case. Store the case in the trunk.
■ TPMS and the Compact Spare Tire
U.S. models If you replace a flat tire with the compact spare tire, the low tire pressure/TPMS indicator comes on while you are driving. After driving for a few miles (kilometers), the indicator will start blinking for a short time and then stay on. CHECK TPMS SYSTEM appears on the intelligent multi-information display (i-MID), but this is normal.
If you replace the tire with a specified regular tire, the warning message on the i-MID and the low tire pressure/TPMS indicator will go off after a few miles (kilometers).
1Storing the Flat Tire
3WARNING
Loose items can fly around the interior in a crash and can seriously injure the occupants.
Store the wheel, jack, and tools securely before driving.
1TPMS and the Compact Spare Tire
The system cannot monitor the pressure of the compact spare tire. Manually check the compact spare tire pressure to be sure that it is correct.
Use TPMS specific wheels. Each is equipped with a tire pressure sensor mounted inside the tire behind the valve stem.
QRG
TOC
Index
Home
310
13 CIVIC HYBRID-31TR26100.book 311 ページ 2012年12月18日 火曜日 午後2時59分
Engine Does Not Start
Checking the Engine If the engine does not start, check the starter.
1Checking the Engine
If you must start the vehicle immediately, use an assisting vehicle to jump start it.
2 Jump Starting P. 312
Starter condition
Starter doesn’t turn or turns over slowly. The 12 volt battery may be dead. Check each of the items on the right and respond accordingly.
The starter turns over normally but the engine doesn’t start. There may be a problem with the fuse. Check each of the items on the right and respond accordingly.
Checklist
Check brightness of the interior light. Turn on interior lights and check brightness. ● If the interior lights are dim or do not come on at all
2 12 Volt Battery P. 288
● If the interior lights come on normally
2 Fuses P. 321
Review the engine start procedure. Follow its instructions, and try to start the engine again.
2 Starting the Engine P. 214
Check the immobilizer system indicator. When the immobilizer system indicator is blinking, the engine cannot be started.
2 Immobilizer System P. 115
Check the fuel level. There should be enough fuel in the tank.
2 Fuel Gauge P. 82
Check the fuse. Check all fuses, or have the vehicle checked by a dealer.
2 Inspecting and Changing Fuses P. 323
If the problem continues:
2 Emergency Towing P. 324
QRG
TOC
Index
Home
311
13 CIVIC HYBRID-31TR26100.book 312 ページ 2012年12月18日 火曜日 午後2時59分
Jump Starting
■ Jump Starting Procedure Turn off the power to electric devices, such as audio and lights. Turn off the engine, then open the hood.
Booster Battery
1. Connect the first jumper cable to your
vehicle’s battery + terminal.
2. Connect the other end of the first jumper
cable to the booster battery + terminal. u Use a 12-volt booster battery only.
3. Connect the second jumper cable to the
booster battery - terminal.
4. Connect the other end of the second
jumper cable to the engine mounting bolt as shown. Do not connect this jumper cable to any other part.
5. If your vehicle is connected to another
vehicle, start the assisting vehicle’s engine and increase its rpm slightly.
6. Attempt to start your vehicle’s engine. If it
turns over slowly, check that the jumper cables have good metal-to-metal contact.
1Jump Starting
3WARNING
A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby.
Keep all sparks, open flames, and smoking materials away from the battery.
Securely attach the jumper cables clips so that they do not come off when the engine vibrates. Also be careful not to tangle the jumper cables or allow the cable ends to touch each other while attaching or detaching the jumper cables.
Battery performance degrades in cold conditions and may prevent the engine from starting.
QRG
TOC
Index
Home
312
13 CIVIC HYBRID-31TR26100.book 313 ページ 2012年12月18日 火曜日 午後2時59分
uuJump Startingu
■ What to Do After the Engine Starts Once your vehicle’s engine has started, remove the jumper cables in the following order.
1. Disconnect the jumper cable from your vehicle’s ground.
2. Disconnect the other end of the jumper cable from the booster
battery - terminal.
3. Disconnect the jumper cable from your vehicle’s battery + terminal.
4. Disconnect the other end of the jumper cable from the booster
battery + terminal.
Have your vehicle inspected by a nearby service station or a dealer.
QRG
TOC
Index
Home
313
13 CIVIC HYBRID-31TR26100.book 314 ページ 2012年12月18日 火曜日 午後2時59分
Shift Lever Does Not Move
Follow the procedure below if you cannot move the shift lever out of (P position.
■ Releasing the Lock
1. Set the parking brake.
2. Remove the key from the ignition switch.
3. Wrap a cloth around the tip of a small flat-
tip screwdriver. Put it into the shift lock release slot as shown in the image, and remove the cover.
4. Insert the key into the shift lock release slot.
5. While pushing the key down, press the shift lever release button and place the shift lever into (N. u The lock is now released. Have the
shift lever checked by a dealer as soon as possible.
Slot
Cover
Shift Lock Release Slot
QRG
TOC
Release Button
Index
Home
314
13 CIVIC HYBRID-31TR26100.book 315 ページ 2012年12月18日 火曜日 午後2時59分
Overheating
How to Handle Overheating Overheating symptoms are as follows: • The high temperature indicator comes on or the engine suddenly loses power.
• Steam or spray comes out of the engine compartment.
■ First thing to do 1. Immediately park the vehicle in a safe place.
2. Turn off all accessories and turn on the hazard warning lights.
u No steam or spray present: Keep the engine running and open the hood. u Steam or spray is present: Turn off the engine and wait until it subsides.
Then open the hood.
1How to Handle Overheating
3WARNING
Steam and spray from an overheated engine can seriously scald you.
Do not open the hood if steam is coming out.
NOTICE Continuing to drive with the high temperature indicator on may damage the engine.
Continued
QRG
TOC
Index
Home
315
13 CIVIC HYBRID-31TR26100.book 316 ページ 2012年12月18日 火曜日 午後2時59分
uuOverheatinguHow to Handle Overheating
QRG
■ Next thing to do
MAX
MIN
Reserve Tank
1. Check that the cooling fan is operating and stop the engine once the high temperature indicator goes off. u If the cooling fan is not operating,
immediately stop the engine.
2. Once the engine has cooled down, inspect
the coolant level and check the cooling system components for leaks. u If the coolant level in the reserve tank is
low, add coolant until it reaches the MAX mark.
u If there is no coolant in the reserve tank, check that the radiator is cool. Cover the radiator cap with a heavy cloth and open the cap. If necessary, add coolant up to the base of the filler neck, and put the cap back on.
1How to Handle Overheating
3WARNING
Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiator cap.
If the coolant is leaking, contact a dealer for repairs.
Use water as an emergency/temporary measure only. Have a dealer flush the system with proper antifreeze as soon as possible.
■ Last thing to do Once the engine has cooled sufficiently, restart it and check the high temperature indicator.
If the high temperature indicator is off, resume driving. If it stays on, contact a dealer for repairs.
TOC
Index
Home
316
13 CIVIC HYBRID-31TR26100.book 317 ページ 2012年12月18日 火曜日 午後2時59分
Indicator, Coming On/Blinking
If the Low Oil Pressure Indicator Comes On
■ Reasons for the indicator to come on Comes on when the engine oil pressure is low. ■ What to do as soon as the indicator comes on 1. Immediately park the vehicle on level ground in a safe place.
2. If necessary, turn the hazard warning lights on. ■ What to do after parking the vehicle 1. Stop the engine and let it sit for about three minutes.
2. Open the hood and check the oil level.
u Add oil as necessary.
2 Oil Check P. 262
3. Start the engine and check the low oil pressure indicator.
u The light goes out: Start driving again. u The light does not go out within 10 seconds: Stop the engine and
contact a dealer for repairs immediately.
If the 12 Volt Battery Charging System Indicator Comes On
1If the Low Oil Pressure Indicator Comes On
NOTICE Running the engine with low oil pressure can cause serious mechanical damage almost immediately.
■ Reasons for the indicator to come on Comes on when the 12 volt battery is not being charged. ■ What to do when the indicator comes on Turn off the climate control system, rear defogger, and other electrical systems, and immediately contact a dealer for repairs.
1If the 12 Volt Battery Charging System Indicator Comes On
If you need to stop temporarily, do not turn off the engine. Restarting the engine may rapidly discharge the 12 volt battery.
This indicator may blink after starting when the outside temperature is below -20°F (-30°C). It will stop blinking after the IMA battery warms up.
QRG
TOC
Index
Home
317
1If the Malfunction Indicator Lamp Comes On or Blinks
NOTICE If you drive with the malfunction indicator lamp on, the emissions control system and the engine could be damaged.
If the malfunction indicator lamp blinks again when restarting the engine, drive to the nearest dealer at 31 mph (50 km/h) or less. Have your vehicle inspected.
13 CIVIC HYBRID-31TR26100.book 318 ページ 2012年12月18日 火曜日 午後2時59分
uuIndicator, Coming On/BlinkinguIf the Malfunction Indicator Lamp Comes On or Blinks
QRG
If the Malfunction Indicator Lamp Comes On or Blinks
■ Reasons for the indicator lamp to come on or blink • Comes on when there is a problem with the engine emissions control
system, or the fuel fill cap is missing, or loose.
• Blinks when engine misfiring is detected. ■ What to do when the indicator lamp comes on Avoid high speeds and immediately get your vehicle inspected by a dealer. ■ What to do when the indicator lamp blinks Park the vehicle in a safe place with no flammable items and wait at least ten minutes or more with the engine stopped until it cools.
■ Tighten Fuel Cap Message ■ The message appears on when: An evaporative system leak is detected. This may be caused by the fuel fill cap being loose or not being installed. ■ What to do when the message appears: 1. Stop the engine.
2. Check that the fuel fill cap is fully installed.
u If not, loosen the cap, and then retighten it until it clicks at least once.
3. Drive for several days of normal driving.
u The message should go off.
■ When the malfunction indicator lamp comes on Malfunction indicator lamp comes on if the system continues to detect a leak of gasoline vapor. If this happens, check the fuel fill cap using the procedures described above.
TOC
Index
Home
318
13 CIVIC HYBRID-31TR26100.book 319 ページ 2012年12月18日 火曜日 午後2時59分
uuIndicator, Coming On/BlinkinguIf the Brake System Indicator (Red) Comes On
If the Brake System Indicator (Red) Comes On
U.S.
■ Reasons for the indicator to come on • The brake fluid is low.
• There is a malfunction in the brake system.
Canada
■ What to do when the indicator comes on while driving Press the brake pedal lightly to check pedal pressure. • If normal, check the brake fluid level the next time you stop.
• If abnormal, take immediate action. If necessary, downshift the
transmission to slow the vehicle using engine braking.
1If the Brake System Indicator (Red) Comes On Have your vehicle repaired immediately. It is dangerous to drive with low brake fluid. If there is no resistance from the brake pedal, stop immediately in a safe place. If necessary downshift the transmission.
If the brake system indicator and ABS indicator come on simultaneously, the electronic brake distribution system is not working. This can result in vehicle instability under sudden braking.
Have your vehicle inspected by a dealer immediately.
If the EPS System Indicator Comes On
1If the EPS System Indicator Comes On
■ Reasons for the indicator to come on • Comes on when there is a problem with EPS system.
• If you depress the accelerator pedal repeatedly to increase the engine
speed while the engine is idling, the indicator comes on, and sometimes the steering wheel becomes harder to operate.
■ What to do when the indicator comes on Stop the vehicle in a safe place and restart the engine. If the indicator comes on and stays on, immediately have your vehicle inspected by a dealer.
NOTICE If you repeatedly turn the steering wheel at an extremely low speed, or hold the steering wheel on the full left or right position for a while, the system heats up. The system goes into a protective mode, and limits its performance. The steering wheel becomes harder and harder to operate. Once the system cools down, EPS system is restored. Repeated operation under these conditions can eventually damage the system.
QRG
TOC
Index
Home
319
13 CIVIC HYBRID-31TR26100.book 320 ページ 2012年12月18日 火曜日 午後2時59分
uuIndicator, Coming On/BlinkinguIf the IMA Indicator Comes On
QRG
If the IMA Indicator Comes On
■ Reasons for the indicator to come on Comes on when there is a problem with the IMA system.
■ What to do when the indicator come on Avoid high speeds and immediately get your vehicle inspected by a dealer.
U.S. models If the Low Tire Pressure/TPMS Indicator Comes On or Blinks
■ Reasons for the indicator to come on or blink A tire pressure is significantly low. If there is a problem with the TPMS or the compact spare tire is installed, the indicator blinks for about one minute, and then stays on.
■ What to do when the indicator comes on Stop your vehicle in a safe place. Check the tire pressure and adjust the pressure to the specified level. The specified tire pressure is on a label on the driver side doorjamb.
■ What to do when the indicator blinks Have the tire inspected by a dealer as soon as possible. If the compact spare tire * causes the indicator to blink, change the tire to a full-size tire. The indicator goes off after driving for a few miles (kilometers).
* Not available on all models
TOC
Index
Home
320
1If the Low Tire Pressure/TPMS Indicator Comes On or Blinks
NOTICE Driving on an extremely underinflated tire can cause it to overheat. An overheated tire can fail. Always inflate your tires to the prescribed level.
13 CIVIC HYBRID-31TR26100.book 321 ページ 2012年12月18日 火曜日 午後2時59分
Fuses
Fuse Locations If any electrical devices are not working, turn the ignition switch to LOCK (0 and check to see if any applicable fuse is blown.
■ Engine Compartment Fuse Box Located near the brake fluid reservoir. Push the tabs to open the box.
■ Circuit protected and fuse rating
Circuit Protected
EPS
Booster Motor ABS/VSA Motor ABS/VSA FSR
−
Main Fuse IG Main
Fuse Box Main
Fuse Box Main 2
Headlight Main
−
Fuse locations are shown on the fuse box cover.
Locate the fuse in question by the fuse number and box cover number.
Rear Defogger
−
Blower
−
Sub Fan Motor Main Fan Motor
−
IG Coil 2
Starter DIAG, ST MG
IG Coil 1
− − − −
10
Amps 70 A 40 A 30 A 30 A
−
100 A 50 A 60 A 60 A 30 A
−
30 A
−
40 A
−
20 A 20 A
−
15 A 7.5 A 15 A
− − − −
QRG
Amps 7.5 A
10 A
Circuit Protected
Oil Level
LED Daytime Running
11
12
Lights
IMA 1
Hazard
FI Sub
IG Coil
Stop
Horn
IMA 2
7.5 A
13
10 A
14
15 A
15
20 A
16
15 A
17
10 A
18
19
10 A
20 Right Headlight Low Beam 10 A
15 A
21
22
15 A
10 A
23
15 A
24
25
7.5 A
26
27
28
29
Booster SOL MG Clutch
Left Headlight Low Beam
20 A 7.5 A 10 A
Interior Lights
IGP DBW
Backup
SMALL
−
−
TOC
Index
Home
Continued
321
13 CIVIC HYBRID-31TR26100.book 322 ページ 2012年12月18日 火曜日 午後2時59分
uuFusesuFuse Locations
■ Interior Fuse Box Located under the dashboard.
Fuse Label
Fuse locations are shown on the label on the side panel.
Locate the fuse in question by the fuse number and label number.
■ Circuit protected and fuse rating
Circuit Protected
−
ACG SRS
Fuel Pump
8 Door Lock Motor 2 (Unlock) 9 Door Lock Motor 1 (Unlock)
Power Window
VB SOL
Meter
Amps
−
10 A 10 A 15 A 7.5 A 7.5 A (15 A) 15 A 15 A
* Not available on all models
QRG
TOC
Index
Home
322
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
− −
Accessory Power Socket
(Center Console) *
−
Seat Heaters *
Driver’s Door Lock Motor
(Unlock)
− − −
ACC
ACC Key Lock
Daytime Running Lights
HAC HAC
ABS/VSA
− −
Accessory Power Socket
(Front) Washer
ODS
Driver’s Door Lock Motor
(Lock)
31
32 Door Lock Motor 2 (Lock)
−
− −
(20 A)
−
(15 A)
(10 A)
− − −
7.5 A 7.5 A 7.5 A 7.5 A (7.5 A) 7.5 A
− −
20 A
15 A 7.5 A
(10 A)
−
15 A
Circuit Protected
Amps
Circuit Protected
Amps 15 A 7.5 A 7.5 A
− −
Small Lights Illumination
33 Door Lock Motor 1 (Lock)
34
35
36
37
38
10 A
39 Right Headlight High Beam 10 A
40
(7.5 A)
20 A
41
42
20 A
Left Headlight High Beam
Door Lock
TPMS *
Driver’s Power Window Rear Passenger’s Side
− −
43
44
45
46
Power Window
Front Passenger’s Side
Power Window
Rear Driver’s Side Power
Window Wiper
(20 A)
20 A
(20 A)
30 A
13 CIVIC HYBRID-31TR26100.book 323 ページ 2012年12月18日 火曜日 午後2時59分
uuFusesuInspecting and Changing Fuses
Inspecting and Changing Fuses
1. Turn the ignition switch to LOCK (0. Turn
1Inspecting and Changing Fuses
Blown Fuse
headlights and all accessories off.
2. Remove the fuse box cover.
3. Check the large fuse in the engine
compartment. u If the fuse is blown, use a Phillips-head
screwdriver to remove the screw and replace it with a new one.
4. Inspect the small fuses in the engine compartment and the vehicle interior. u If there is a burned out fuse, remove it
with the fuse puller and replace it with a new one.
NOTICE Replacing a fuse with one that has a higher rating greatly increases the chances of damaging the electrical system.
Replace fuse with a spare fuse of the same specified amperage. Confirm the specified amperage using the charts on P. 321 to 322.
There is a fuse puller on the back of the engine compartment fuse box cover.
Combined Fuse
Fuse Puller
QRG
TOC
Index
Home
323
13 CIVIC HYBRID-31TR26100.book 324 ページ 2012年12月18日 火曜日 午後2時59分
Emergency Towing
Call a professional towing service if you need to tow your vehicle.
1Emergency Towing
■ Flat bed equipment The operator loads your vehicle on the back of a truck. This is the best way to transport your vehicle.
■ Wheel lift equipment The tow truck uses two pivoting arms that go under the front tires and lift them off the ground. The rear tires remain on the ground. This is an acceptable way to tow your vehicle.
NOTICE Trying to lift or tow your vehicle by the bumpers will cause serious damage. The bumpers are not designed to support the vehicle’s weight.
NOTICE Improper towing such as towing behind a motorhome or other motor vehicle can damage the transmission.
Never tow your vehicle with just a rope or chain. It is very dangerous, since ropes or chains may shift from side to side or break.
QRG
TOC
Index
Home
324
13 CIVIC HYBRID-31TR26100.book 325 ページ 2012年12月18日 火曜日 午後2時59分
Information
QRG
This chapter includes your vehicle’s specifications, locations of identification numbers, and other information required by regulation.
Specifications .................................... 326
Identification Numbers
Vehicle Identification Number (VIN).. 328
Engine Number and Transmission
Number...................................... 328
Devices that Emit Radio Waves ....... 329
Reporting Safety Defects ................. 330
Emissions Testing
Testing of Readiness Codes.............. 331
Warranty Coverages ........................ 333
Authorized Manuals......................... 335
Customer Service Information......... 336
Index
Home
325
13 CIVIC HYBRID-31TR26100.book 326 ページ 2012年12月18日 火曜日 午後2時59分
Specifications
QRG
91 cu-in (1,497 cm3) NGK
DILFR6J11
■ Engine Specifications Displacement Spark Plugs ■ Fuel Fuel: Type Fuel Tank Capacity ■ 12 Volt Battery Capacity/Type ■ Washer Fluid
32AH(5)/40AH(20)
Unleaded gasoline, Pump octane number of 87 or higher 13.2 US gal (50 ℓ)
Tank Capacity
U.S.: 2.6 US qt (2.5 ℓ) Canada: 4.8 US qt (4.5 ℓ)
■ Light Bulbs Headlights (Low Beam) Headlights (High Beam) Front Turn Signal/Parking/Side Marker Lights Daytime Running Lights Rear Side Marker Lights Brake/Taillights Side Turn Signal Lights (on Door Mirrors) Back-Up Lights Taillights Rear Turn Signal Lights High-Mount Brake Light License Plate Light Trunk Light Interior Lights
51W (HB4) 60W (HB3)
28/8W
LED LED LED
LED
16W LED 21W (Amber) LED 5W 5W
Spotlight Ceiling Light
8W 8W
Honda Civic Hybrid
■ Vehicle Specifications Model No. of Passengers: Front Rear Total Weights: Gross Vehicle Weight Rating Gross Axle Weight Rating (Front)
U.S.: 3,837 lbs (1,740 kg) Canada: 1,740 kg
U.S.: 2,007 lbs (910 kg) Canada: 910 kg
Gross Axle Weight Rating (Rear)
Air Conditioning: Refrigerant Type Charge Quantity Lubricant Type
U.S.: 1,852 lbs (840 kg) Canada: 840 kg
HFC-134a (R-134a) 13.2 – 15.0 oz (375 – 425 g) SE-10Y
TOC
Index
Home
326
13 CIVIC HYBRID-31TR26100.book 327 ページ 2012年12月18日 火曜日 午後2時59分
■ Brake Fluid Specified ■ Transmission Fluid
Honda Heavy Duty Brake Fluid DOT 3
Specified
Capacity
Honda CVTF (continuously variable transmission fluid) Change
2.95 US qt (2.8 ℓ)
■ Engine Oil
Capacity
Recommended
3.6 US qt (3.4 ℓ)
·Genuine Honda Motor Oil 0W-20
·API Premium-grade 0W-20 detergent oil
Change
Change
including
filter
■ Engine Coolant
Specified
Ratio
Honda Long-Life Antifreeze/Coolant Type2
50/50 with distilled water
1.37 US gal (5.18 ℓ)
(change including the remaining
0.125 US gal (0.475 ℓ) in the reserve tank)
3.8 US qt (3.6 ℓ)
Capacity
uuSpecificationsu
QRG
■ Tire
Regular
Compact
Spare*1
Wheel Size
*1: Optional
Size
Pressure
Size
Pressure
Regular
Compact Spare*1
P195/65R15 89S 32 psi (220 kPa [2.2 kgf/cm2]) T135/80D15 99M 60 psi (420 kPa [4.2 kgf/cm2]) 15 x 6J 15 x 4T
TOC
Index
Home
327
13 CIVIC HYBRID-31TR26100.book 328 ページ 2012年12月18日 火曜日 午後2時59分
Identification Numbers
QRG
Vehicle Identification Number (VIN) Your vehicle has a 17-digit vehicle identification number (VIN) used to register your vehicle for warranty purposes, and for licensing and insuring your vehicle. See the image below for the VIN locations.
Engine Number and Transmission Number See the image below for the locations of your vehicle’s engine number and transmission number.
Engine Number
Vehicle Identification Number
IMA Motor Number
Transmission Number
Certification Label/ Vehicle Identification Number
TOC
Index
Home
328
13 CIVIC HYBRID-31TR26100.book 329 ページ 2012年12月18日 火曜日 午後2時59分
Devices that Emit Radio Waves
The following products and systems on your vehicle emit radio waves when in operation.
Audio System Bluetooth® Audio Bluetooth® HandsFreeLink® Immobilizer System Remote Transmitter Tire Pressure Monitoring System (TPMS) (U.S. models only)
Each of the above complies with the appropriate requirements or the required standards of FCC (Federal Communications Commission) and Industry Canada Standard, described below:
As required by the FCC: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Industry Canada Standard RSS-Gen/210/310. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
QRG
TOC
Index
Home
329
13 CIVIC HYBRID-31TR26100.book 330 ページ 2012年12月18日 火曜日 午後2時59分
Reporting Safety Defects
In the U.S. If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Admini stration (NHTSA) in addition to notifying American Honda Motor Co., Inc.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or American Honda Motor Co., Inc.
To contact NHTSA, you may:
call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to or write to: Administrator, NHTSA
http://www.safercar.gov;
1200 New Jersey Avenue, SE.,
Washington, DC 20590.
You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
In Canada If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform Honda Canada Inc. and you may also inform Transport Canada.
If Transport Canada receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may lead to a recall and remedy campaign. However, Transport Canada cannot become involved in individual problems between you, your dealer, or Honda Canada Inc.
To contact Transport Canada’s Defect Investigations and Recalls Division, you may call 1-800-333-0510. For more information on reporting safety defects or about motor vehicle safety, go to http://www.tc.gc.ca/ roadsafety.
QRG
TOC
Index
Home
330
13 CIVIC HYBRID-31TR26100.book 331 ページ 2012年12月18日 火曜日 午後2時59分
Emissions Testing
Testing of Readiness Codes Your vehicle uses “readiness codes,” as part of its onboard self diagnostic system. Some states refer to these codes during testing to see if your vehicle’s emissions components are working properly.
The codes may not be read if you go through the testing just after the battery has gone dead or been disconnected.
To check if they are set, turn the ignition switch to ON (w, without starting the engine. The malfunction indicator lamp will come on for several seconds. If it then goes off, the readiness codes are set. If it blinks five times, the readiness codes are not set.
If you are required to have your vehicle tested before the readiness codes are ready, prepare the vehicle for retesting by doing the following:
1. Fill the gas tank to approximately 3/4 full.
2. Park the vehicle and leave the engine off for 6 hours or more.
3. Make sure the ambient temperature is between 40 °F and 95 °F (4 °C and 35 °C).
4. Start the engine without touching the accelerator pedal, and let it idle for
20 seconds.
5. Keep the vehicle in (P. Increase the engine speed to 2,000 rpm, and hold it there
for about 3 minutes.
6. Let the engine idle with your foot off the accelerator for 20 seconds.
Continued
1Testing of Readiness Codes
The readiness codes are erased when the 12 volt battery is disconnected, and set again only after several days of driving under a variety of conditions.
If a testing facility determines that the readiness codes are not set, you may be requested to return at a later date to complete the test.
If the testing facility determines the readiness codes are still not set, see a dealer.
QRG
TOC
Index
Home
331
13 CIVIC HYBRID-31TR26100.book 332 ページ 2012年12月18日 火曜日 午後2時59分
uuEmissions TestinguTesting of Readiness Codes
7. Select a nearby, lightly traveled major highway where you can maintain a speed of 50 to 60 mph (80 to 97 km/h) for at least 20 minutes. Drive on the highway in (D. Do not use cruise control. When traffic allows, drive for 90 seconds without moving the accelerator pedal. (Vehicle speed may vary slightly; this is okay.) If you cannot do this for a continuous 90 seconds because of traffic conditions, drive for at least 30 seconds, then repeat it two more times (for a total of 90 seconds).
8. Drive in city/suburban traffic for at least 10 minutes. When traffic conditions
allow, let the vehicle coast for several seconds without using the accelerator pedal or the brake pedal.
9. Park the vehicle and leave the engine off for 30 minutes.
QRG
TOC
Index
Home
332
13 CIVIC HYBRID-31TR26100.book 333 ページ 2012年12月18日 火曜日 午後2時59分
Warranty Coverages
■ U.S. Owners Your new vehicle is covered by these warranties:
New Vehicle Limited Warranty – covers your new vehicle, except for the emissions control systems and accessories, against defects in materials and workmanship.
Emissions Control Systems Defects Warranty and Emissions Performance Warranty – these two warranties cover your vehicle’s emissions control systems. Time, mileage, and coverage are conditional. Please read your warranty booklet for exact information.
Seat Belt Limited Warranty – a seat belt that fails to function properly is covered by a limited warranty. Please read your warranty booklet for details.
Rust Perforation Limited Warranty – all exterior body panels are covered for rust-through from the inside for the specified time period with no mileage limit.
Accessory Limited Warranty – Honda accessories are covered under this warranty. Time and mileage limits depend on the type of accessory and other factors. Please read your warranty booklet for details.
Replacement Parts Limited Warranty – covers all Honda replacement parts against defects in materials and workmanship.
Continued
QRG
TOC
Index
Home
333
13 CIVIC HYBRID-31TR26100.book 334 ページ 2012年12月18日 火曜日 午後2時59分