1996 Honda Accord Wagon Owners Manual

which would not be covered by your warranty. Improperly designed accessories can adversely affect your car's handling and stability.

Your car has several computer-controlled systems,

Accessories

including the SRS system, the engine's fuel injection, and the anti-lock brake system. Strong electronic interference can affect their operation.

accessories installed by qualified technicians who are familiar with your Honda. If possible, have your Honda dealer inspect the final installation.

Electronic communications equipment, such as cellular telephones and two-way radios are regulated by the FCC and should not interfere with your car's systems. Improper installation or using electrical equipment not intended for mobile use may interfere with your car's operation. If you want to install a cellular telephone, other mobile communications equipment, or even add-on stereo amplifiers, please discuss it first with your Honda dealer.

In many cases, improper installation is the real cause of problems with aftermarket accessories. Have these

Before Driving

This section gives you tips on starting the engine under various conditions and how to operate the 5-speed manual and automatic transmissions. It also includes important information on your car's braking system and facts you need if you are planning to tow a trailer.

Driving

Preparing to Drive . . . . . . . . .. 94
Starting the Engine . . . . . . . . .. 94

Starting in Cold Weather at

High Altitude . . . . . . . . . .. 95

5-Speed Manual

Transmission . . . . . . . . . . . .. 95
Recommended Shift

Points . . . . . . . . . . . . . . . . .. 96
Maximum Speeds . . . . . . . .. 97
Automatic Transmission . . . .. 97

Shift Lever Position

Indicator . . . . . . . . . . . . . .. 97
Shift Lever Positions . . . . .. 98
Maximum Speeds . . . . . . .. 100
Shift Lock Release . . . . . .. 100
The Braking System . . . . . . .. 101
Brake Wear Indicators . .. 101
Brake System Design . . . .. 101
Anti-Lock Brakes . . . . . . .. 102
Towing a Trailer . . . . . . . . . .. 103

Driving

Preparing to Drive, Starting the Engine

You should do the following checks and adjustments every day before you drive your car.

1. Make sure all windows,

mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice.

2. Check that the hood and

trunk are fully closed.

3. Visually check the tires. If a

tire looks low, use a gauge to check its pressure.

4. Check that any items you may be carrying with you inside are stored properly or fastened down securely.

5. Check the adjustment of the

seat (see page 48).

6. Check the adjustment of the

inside and outside mirrors (see page 53).

7. Check the adjustment of the steering wheel (see page 40).

Driving

8. Make sure the doors are

securely closed and locked. 9. Fasten your seat belt. Check

that your passengers have fastened their seat belts (see page 7).

10. Turn the ignition ON (II).

Check the indicator lights in the instrument panel.

11. Start the engine. 12. Check the gauges and indicator lights in the instrument panel (see page 29).

Starting the Engine 1. Apply the parking brake. 2. In cold weather, turn off all

electrical accessories to reduce the drain on the battery.

3. Manual transmission: Push

the clutch pedal all the way down. START (III) does not function unless the clutch pedal is depressed. Automatic transmission: Make sure the shift lever is in Park. Press on the brake pedal.

4. Without touching the

accelerator pedal, turn the ignition key to the START (III) position. If the engine does not start right away, do not hold the key in START (III) for more than 15 seconds at a time. Pause for at least 10
seconds before trying again. If the engine does not start within 15 seconds or starts but stalls right away, repeat step 4 with the accelerator pedal pressed. If the engine starts, release pressure on the accelerator pedal so the engine does not race.

5.

Starting the Engine, 5-Speed Manual Transmission

2. Press the accelerator pedal

halfway down, and hold it there while starting the engine. Do not hold the ignition key in START (III) for more than 15 seconds. When the engine starts, release the accelerator pedal gradually as the engine speeds up and smooths out. If the engine fails to start in step 2, press the accelerator pedal all the way down, and hold it there while you try to start the engine for no more than 15 seconds. If the engine does not start, return to step 2.

3.

6.

If the engine still does not start, press the accelerator pedal all the way down and hold it there while starting to clear any flooding. As before, keep the ignition key in the START (III) position for no more than 15 seconds. Return to step 5 if the engine does not start. If it starts, lift your foot off the accelerator pedal so the engine does not race.

Starting in Cold Weather at High Altitude (Above 8,000 Feet/2,400 Meters) An engine is harder to start in cold weather. The thinner air found at high altitude above 8,000 feet (2,400 meters) adds to the problem. Use the following procedure:

1. Turn off all electrical

accessories to reduce the drain on the battery.

5-Speed Manual Transmission The manual transmission is synchronized in all forward gears for smooth operation. It has a lockout so you cannot shift directly from Fifth to Reverse. When shifting up or down, make sure you press the clutch pedal down all the way, shift to the next gear, and let the pedal up gradually. When you are not shifting, do not rest your foot on the clutch pedal. This can cause your clutch to wear out faster.

continued

Driving

5-Speed Manual Transmission

Recommended Shift Points Drive in the highest gear that lets the engine run and accelerate smoothly. This will give you the best fuel economy and effective emissions control. The following shift points are recommended:

Rapid slowing or speeding up can cause loss of control on slippery surfaces. If you crash, you can be injured.

Use extra care when driving on slippery surfaces.

Come to a full stop before you shift into reverse. You can damage the transmission by trying to shift into reverse with the car moving. Push down the clutch pedal, and pause for a few seconds before shifting into reverse, or shift into one of the forward gears for a moment. This stops the gears so they won't "grind."

When slowing down, you can get extra braking from the engine by shifting to a lower gear. This extra braking can help you maintain a safe speed and prevent your brakes from overheating while going down a steep hill. Before downshifting, make sure engine speed will not go into the red zone in the lower gear. Refer to the Maximum Speeds chart.

Driving

5-Speed Manual Transmission, Automatic Transmission

Maximum Speeds The speeds in these tables are the maximums for the given gears. If you exceed these speeds, the engine speed will enter into the tachometer's red zone. If this occurs, you may feel the engine cut in and out. This is caused by a limiter in the engine's computer controls. The engine will run normally when you reduce the rpm below the red zone.

Automatic Transmission Your Honda's transmission has four forward speeds and is electronically controlled for smoother shifting. It also has a "lock-up" torque converter for better fuel economy. You may feel what seems like another shift when the converter locks.

Shift Lever Position Indicator This indicator between the tachometer and speedometer shows which shift position the shift lever is in. The "D4" indicator comes on for a few seconds when you turn the ignition switch ON (II). If it flashes while driving (in any shift position), it indicates a possible problem in the transmission. Avoid rapid acceleration and have the transmission checked by an authorized Honda dealer as soon as possible.

continued

Driving

Automatic Transmission

Shift Lever Positions The shift lever has seven positions. It must be in Park or Neutral to start the engine. When you are stopped in D4, D3, 2, 1 or R, press firmly on the brake pedal, and keep your foot off the accelerator pedal.

SHIFT LEVER

Driving

Park (P) — This position mechanically locks the transmission. Use Park whenever you are turning off or starting the engine. To shift out of Park, you must press on the brake pedal and have your foot off the accelerator pedal. Press the release button on the side of the shift lever to move it.

If you have done all of the above and still cannot move the lever

out of Park, see Shift Lock Release on page 100.

moving the shift lever from Neutral to another gear.

You must also press the release button to shift into Park. To avoid transmission damage, come to a complete stop before shifting into Park. The shift lever must be in Park before you can remove the key from the ignition switch.

Reverse (R) — To shift to Reverse from Park, see the explanation under Park. To shift to Reverse from Neutral, come to a complete stop and then shift. Press the release button before shifting into Reverse from Neutral.

Neutral (N) — Use Neutral if you need to restart a stalled engine or you need to stop briefly with the engine idling. Shift to Park position if you need to leave the car for any reason. Press on the brake pedal when you are

Drive (D4) — Use this position for your normal driving. The transmission automatically selects a suitable gear for your speed and acceleration. You may notice the transmission shifting up at higher speeds when the engine is cold. This helps the engine warm up faster.

Drive (D3) — This position is similar to D4, except only the first three gears may be selected. Use D3 when towing a trailer in hilly terrain or to provide engine braking when going down a steep hill. D3 can also keep the transmission from cycling between third and fourth gears in stop-and-go driving.

For faster acceleration when in D3 or D4, you can get the transmission to automatically

Automatic Transmission

downshift by pushing the accelerator pedal to the floor. The transmission will shift down one or two gears, depending on your speed. Second (2) - To shift to Second, press the release button on the side of the shift lever. This position locks the transmission in second gear. It does not downshift to first gear when you come to a stop. Second gives you more power when climbing, and increased engine braking when going down steep hills. Use second gear when starting out on a slippery surface or in deep snow. It will help reduce wheel spin.

Whenever you move the shift lever to a lower gear, the transmission downshifts only if the engine's redline will not be exceeded in the lower gear.

continued

Driving

Automatic Transmission

First (1) — To shift from Second to First, press the release button on the side of the shift lever. With the lever in this position, the transmission locks in First gear. By upshifting and downshifting through 1, 2, D3, and D4, you can operate this transmission much like a manual transmission without a clutch pedal.

Maximum Speeds The speeds in these tables are the maximums for the given position. If you exceed these speeds, the engine speed will enter into the tachometer's red zone. If this occurs, you will feel the engine cut in and out. This is caused by a limiter in the engine's computer controls. The engine will run normally when you reduce the rpm below the red zone.

Driving

5. Remove the key from the

Shift Lock Release slot. Return the key to the ignition switch, depress the brake pedal, and restart the engine.

RELEASE BUTTON

SHIFT LOCK RELEASE SLOT

If you need to use the Shift Lock Release, it could mean your car is developing a problem. Have the car checked by your Honda dealer.

Shift Lock Release This allows you to move the shift lever out of Park if the normal method of pushing on the brake pedal and pressing the release button does not work.

1. Set the parking brake. 2. Remove the key from the

3.

ignition switch. Insert the key in the Shift Lock Release slot next to the shift lever.

4. Push down on the key while you press the release button and move the shift lever out of Park to Neutral.

The Braking System Your Honda is equipped with front disc brakes. The brakes on the rear wheels may be disc or drum, depending on the model. The braking system is power assisted to reduce the effort needed on the brake pedal.

Put your foot on the brake pedal only when you intend to brake. Resting your foot on the pedal keeps the brakes applied lightly, causing them to build up heat. Heat buildup can reduce how well your brakes work. It also keeps your brake lights on all the time, confusing drivers behind you.

Constant application of the brakes when going down a long hill builds up heat and reduces their effectiveness. Use the engine to assist the brakes by downshifting to a lower gear and taking your foot off the accelerator pedal.

Brake Wear Indicators The front disc brakes and rear brakes of ABS-equipped cars have audible brake wear indicators. When the brake pads need replacing, you will hear a distinctive metallic "screeching" sound when you apply the brakes. If you do not have the brake pads replaced, they will screech all the time.

Your brakes may sometimes squeal or squeak when you apply them lightly. Do not confuse this with the brake wear indicators. They make a very audible "screeching."

Brake System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the car (the left-front brake is connected with the right-rear brake, etc.). If

The Braking System

one circuit should develop a problem, you will still have braking at two wheels.

FRONT

If this happens, you will notice that the brake pedal goes down much farther and you need to press on it much harder. A much longer distance will be needed to stop the car.

Slow the car by downshifting to a lower gear and removing your foot from the accelerator pedal. Pull to the side of the road as soon as it is safe. Because of the longer stopping distance needed, continued

Driving

The Braking System

brake system failure is very hazardous. You should have your car towed, but if you must drive the car in this condition, be extremely cautious. Have your car repaired as soon as possible.

Anti-Lock Brakes The EX Wagon has an Anti-lock Brake System (ABS) as standard equipment. ABS helps you to maintain steering control during hard braking. It does this by helping to prevent the wheels from locking up and skidding.

The ABS is always "ON." It requires no special effort or driving technique. You will feel a pulsation in the brake pedal when the ABS activates.

Activation varies with the amount of traction your tires have. On dry pavement, you will need to press on the brake pedal

Driving

very hard before you feel the pedal pulsation that means the ABS has activated. However, you may feel the ABS activate immediately if you are trying to stop on snow or ice. Under all conditions, the ABS is helping to prevent the wheels from locking so you can retain steering control. You should continue to press on the brake pedal with the same force.

You may feel a slight movement of the brake pedal just after you start the engine. This is the ABS working.

The ABS is self-checking. If anything goes wrong, the ABS indicator on the instrument panel comes on (see page 31). This means the anti-lock function of the braking system has shut down. The brakes still work like a conventional system, providing normal stopping ability. You

should have the dealer inspect your car as soon as possible.

ABS INDICATOR

*U.S. Indicator shown.

A car with ABS may require a longer distance to stop on loose or uneven surfaces than an equivalent car without anti-lock brakes. The ABS cannot make up for road conditions or bad judgment. It is still your responsibility to drive at reasonable speeds for weather and traffic conditions and to leave a margin of safety.

Towing a Trailer Your Honda is designed primarily to carry passengers and their cargo. You can use it to tow a trailer if you carefully observe some general rules.

The total weight of the trailer and everything loaded in it must not exceed 1,000 Ib (450 kg). The "tongue load" should never exceed 100 Ib (45 kg). This is the amount of weight the trailer puts on the hitch when it is fully loaded. As a rule of thumb, the tongue load should be 10% of the total trailer package.

For example, if the trailer and its load weigh 500 Ib (225 kg), the tongue load should be 50 Ib (22.5 kg). Adjust the trailer's cargo to change the tongue load. Start by putting

approximately 60% of the cargo toward the front and 40% toward the rear. Never load the trailer so the back is heavier than the front. This takes weight off your car's rear axle and reduces traction.

The combined weight of the car, all passengers and their luggage, and tongue load must not exceed the Gross Vehicle Weight Rating. The GVWR is printed on the Certification Label attached to the driver's doorjamb (see page 176). The combined weight of the car, all passengers and their luggage, and tongue load also must not exceed the Gross Axle Weight Rating. The GAWR is also shown on the Certification label. It tells you the maximum load for the front and rear axles. It is

Towing a Trailer

possible that your towing package does not exceed the GVWR but does exceed the GAWR. Improper trailer loading, and/or too much luggage in the trunk can overload the rear axle. Redistribute the load, and check the axle weights again.

Improperly loading your car and trailer can seriously affect its steering and braking performance, causing a crash in which you can be seriously injured.

Check the loading of your car and trailer carefully before starting to drive.

continued

Driving

Towing a Trailer

The best way to confirm that your total towing package is within these specifications is to get it weighed. Load the car and trailer as you normally would while towing, and take them to a public scale. Have them check the total weight and the weight at each axle, and then compare them to the specifications.

Trailer Hitches Your Honda dealer, or the Honda Customer Relations Zone Office, can give you advice on the proper hitch for your car. Never use a hitch that mounts only to the rear bumper. The bumper is not designed to handle that type of load. The hitch should bolt to the under-body of the car and distribute the load over a wide area. Always have a trailer hitch installed by a qualified technician.

Driving

NOTICE A trailer hitch that is not adequate for the size of the trailer, or a hitch that is improperly installed, can cause damage to the underside of your car.

Mirrors Many states and provinces have laws requiring special outside mirrors when you are towing a trailer. Check the laws in your area. You may want to install mirrors, even if they are not required. Hook up the trailer and see how much it obscures your ability to see behind you with the standard mirrors. If you cannot see directly behind you, or have a large blind spot next to the trailer or the car, you should install mirrors intended for towing.

Connecting the Trailer Most trailers that have a gross weight of 1,000 Ib (450 kg) do not have their own braking system. If you are thinking of getting a trailer that does have brakes, make sure they are electrically operated. There are no provisions in your car to tap into its hydraulic braking system. Any attempt to attach the trailer's brakes to your car's hydraulic system, no matter how successful it may seem, will lower braking effectiveness and create a potential hazard.

Always use a safety chain when towing a trailer. Connect the safety chain securely at both ends. Make sure the chain crosses under the tongue so it will catch the trailer if it becomes unhitched. Leave enough slack in the chain so it can't bind in a sharp turn. Do not let it drag on the ground.

Your car has a trailer lighting connector under the cargo area floor. To use the connector, lift the floor and attach the hook at the end of the strap to the roof line.

You will find the connector under the left side box. Refer to the drawing below for the wiring color code and purpose of each connector pin.

Before Starting Out As you are preparing to tow your trailer, do the following:

Measure the trailer's tongue load. You can do this with a bathroom scale. Verify that the hitch and safety chain are securely fastened. Check the condition and air pressure of all tires on the trailer and your car. Low tire

GROUND (BLACK)

LEFT TURN SIGNAL (GREEN/BLUE)

RIGHT TURN SIGNAL (GREEN/YELLOW)

BACK-UP LIGHT (GREEN/BLACK)

BRAKE LIGHT (GREEN/WHITE)

TAILLIGHT (RED/BLACK)

Towing a Trailer

pressure can seriously affect the handling. Also, check the spare tire. With everything loaded and the trailer connected, check that the rear of the car is not sagging. If so, redistribute the load in the car. Check that all lights on the car and trailer are working properly.

Towing Safety Your car will not stop as quickly with a trailer in tow. Leave extra distance between your car and other vehicles. Avoid braking or turning suddenly. This could cause the trailer to jackknife or possibly turn over.

Keep in mind that your total vehicle is now much longer. Leave more room when making continued

Driving

Towing a Trailer

turns. The trailer tracks a smaller arc than the car and can hit or run over something that the car misses. When passing another vehicle, make sure the trailer is clear before changing lanes.

The car/trailer combination is more affected by crosswinds and buffeting. When being passed by a large vehicle, keep a constant speed and steer straight ahead. If there is too much wind buffeting, slow down to get out of the other vehicle's air turbulence.

Towing a trailer puts an extra load on your car. You should have your car serviced according to the maintenance schedule under severe driving conditions on page 113.

This extra load is magnified when you are driving in hilly terrain. Watch the temperature

Driving

gauge closely when climbing hills. If it gets near the hot area, turn off the air conditioning (if it is on). If this does not reduce the heat, it may be necessary to pull to the side of the road and wait for the engine to cool. If the automatic transmission shifts frequently between 3rd and 4th gears, put it in D3 This will help prevent the transmission from overheating. Help keep the brakes from overheating by shifting to a lower gear when going downhill.

If you have to stop while going uphill, do not hold the car in place by pressing the accelerator. This can cause the automatic transmission to overheat. Use the parking brake or footbrake.

When parking your car and trailer, especially on a hill, be

sure to follow all the normal precautions. Turn your front wheels into the curb, set the parking brake firmly, and put the transmission in 1st or Reverse (manual) or Park (automatic). In addition, place wheel chocks at each of the trailer's tires.

Backing up with a trailer is difficult and takes practice. Drive slowly, make small movements with the steering wheel, and have someone stand outside to guide you. Grip the steering wheel on the bottom (rather than the usual position near the top). Move your hand to the left to get the trailer to move to the left, and right to move the trailer right.

This section explains why it is important to keep your car well maintained and to follow basic maintenance safety precautions.

This section also includes Maintenance Schedules for normal driving and severe driving conditions, a Maintenance Record, and instructions for simple maintenance tasks you may want to take care of yourself.

If you have the skills and tools to perform more complex maintenance tasks on your Honda, you may want to purchase the Service Manual. See page 191 for information on how to obtain a copy, or see your Honda dealer.

Maintenance Safety . . . . . . .. 108
Maintenance Schedule . . . .. 110
Maintenance Record . . . . . .. 114

Periodic Checks . . . . . . . . . .. 116
Fluid Locations . . . . . . . . . . .. 117
Engine Oil . . . . . . . . . . . . . . . .. 118
Adding Oil . . . . . . . . . . . . .. 118
Recommended Oil . . . . . .. 118
Synthetic Oil . . . . . . . . . . .. 119
Additives . . . . . . . . . . . . . .. 119
Changing the Oil

and Filter

. . . . . . . . . . . .. 119
Cooling System . . . . . . . . . . .. 121
Adding Engine Coolant . .. 121
Replacing Engine Coolant 122
Windshield Washers . . . . . . .. 125
Transmission Fluid . . . . . . . .. 125
Automatic Transmission . 125
5-Speed Manual

Transmission . . . . . . . . .. 126
Brake and Clutch Fluid . . . .. 127
Brake System . . . . . . . . . .. 127
Anti-Lock Brake System .. 128
Clutch System . . . . . . . . . .. 128
Power Steering . . . . . . . . . . .. 129
Air Cleaner Element . . . . . . .. 129

Maintenance

Spark Plugs . . . . . . . . . . . . . .. 131
Replacement . . . . . . . . . . .. 131
Specifications . . . . . . . . . .. 132
Battery . . . . . . . . . . . . . . . . . .. 132
Windshield Wipers . . . . . . . .. 134
Air Conditioning System . . .. 135
Drive Belts . . . . . . . . . . . . . . .. 136
Tires . . . . . . . . . . . . . . . . . . . .. 137
Inflation . . . . . . . . . . . . . . .. 137
Inspection . . . . . . . . . . . . .. 138
Maintenance . . . . . . . . . . .. 139
Tire Rotation . . . . . . . . . . .. 139
Replacing Tires

and Wheels . . . . . . . . . . .. 140
Wheels and Tires . . . . . . .. 140
Winter Driving . . . . . . . . .. 140
Snow Tires . . . . . . . . . .. 141
Tire Chains . . . . . . . . . .. 141
Lights . . . . . . . . . . . . . . . . . . .. 141
Replacing Bulbs . . . . . . . .. 142
Storing Your Car . . . . . . . . . .. 148

Maintenance

Maintenance Safety

Regularly maintaining your car is the best way to protect your investment. Proper maintenance is essential to your safety and the safety of your passengers. It will also reward you with more economical, trouble-free driving and help reduce air pollution.

Improperly maintaining this car or failing to correct a problem before driving can cause a crash in which you can be seriously hurt and killed.

Always follow the inspection and maintenance recommendations and schedules in this owner's manual.

This section includes instructions for simple maintenance tasks, such as checking and adding oil. Any service items not detailed in this section should be performed by a Honda technician or other qualified mechanic.

Some of the most important safety precautions are given below. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.

Maintenance

Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.

Always follow the procedures and precautions in this owner's manual.

Maintenance Safety

Read the instructions before you begin, and make sure you have the tools and skills required.

To reduce the possibility of fire or explosion, be careful when working around gasoline or batteries. Use a nonflammable solvent, not gasoline, to clean parts. Keep cigarettes, sparks and flames away from the battery and all fuel-related parts. You should wear eye protection and protective clothing when working near the battery or when using compressed air.

Important Safety Precautions Before you begin any maintenance, make sure that your car is parked on level ground and the parking brake is set. Also, be sure the engine is off. This will help to eliminate several potential hazards:

Carbon monoxide poisoning from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine. Burns from hot parts. Let the engine and exhaust system cool before touching any parts. Injury from moving parts. Do not run the engine unless instructed to do so.

Maintenance

Which Schedule to Follow Service your car according to the time and mileage periods on one of the Maintenance Schedules on the following pages. Select the schedule for "Severe Conditions" if most of your driving is done under one or more of the conditions listed on that page. Otherwise, follow the schedule for "Normal Conditions."

Avoid exceeding your car's load limit. This puts excess strain on the engine, brakes, and many other parts of your car. The load limit is shown on the label on the driver's doorjamb. Operate your car on reasonable roads within the legal speed limit. Drive your ear regularly over a distance of several miles (kilometers). Always use unleaded gasoline with a pump octane number of 86 or higher (see page 82).

Maintenance Schedule

Maintenance Schedule The Maintenance Schedule specifies how often you should have your car serviced and what things need attention. It is essential that your car be serviced as scheduled to retain its high level of safety, dependability, and emissions control performance.

The services and time or mileage intervals shown in the maintenance schedule assume you will use your car as normal transportation for passengers and their possessions. You should also follow these recommendations:

Maintenance

We recommend the use of Genuine Honda parts and fluids whenever you have maintenance done. These are manufactured to the same high quality standards as the original components, so you can be confident of their performance and durability.

Your authorized Honda dealer knows your car best and can provide competent, efficient service. However, service at a dealer is not mandatory to keep your warranties in effect.

Maintenance may be done by any qualified service facility or person who is skilled in this type of automotive service. Keep all the receipts as proof of completion, and have the person who does the work fill out the Maintenance Record. Check your warranty booklet for more information.

Maintenance Schedule

U.S. Cars: Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are "certified" to EPA standards.

According to state and federal regulations, failure to perform maintenance on the items marked with an asterisk (*) will not void your emissions warranties. However, Honda recommends that all maintenance services be performed at the recommended time or mileage period to ensure long-term reliability.

Maintenance

Maintenance Schedule (Normal Conditions)

Follow the Normal Conditions Maintenance Schedule if the severe driving conditions specified in the Severe Conditions Maintenance Schedule on the next page do not apply.

Maintenance

Maintenance Schedule (Severe Conditions)

Follow the Severe Conditions Maintenance Schedule if you drive your vehicle MAINLY under one or more of the following conditions:

Driving less than 5 miles (8
km) per trip or, in freezing temperatures, driving less than 10 miles (16 km) per trip. Driving in extremely hot [over 90°F (32°C)] conditions. Extensive idling or long periods of stop-and-go driving. Trailer towing, driving with a car-top carrier, or driving in mountainous conditions. Driving on muddy, dusty, or de-iced roads.

NOTE: If you only OCCASIONALLY drive under a "severe" condition, you should follow the Normal Conditions Maintenance Schedule on the previous page.

Maintenance

Required Maintenance Record

Have your servicing dealer record all Required Maintenance below. Keep receipts for all work done on your car.

Maintenance

Record additional maintenance for severe driving conditions or non-scheduled maintenance on this page (see page 113).

Non-Scheduled Maintenance Record

Maintenance

Lights - Check the operation of the headlights, parking lights, taillights, high-mount brake light, turn signals, brake lights, and license plate lights monthly. See page 141.

Periodic Checks

You should check the following items at the specified intervals. If you are unsure of how to perform any check, turn to the page given.

Engine oil level - Check every time you fill the fuel tank. See page 86. Engine coolant level - Check the radiator reserve tank every time you fill the fuel tank. See page 87. Windshield washer fluid - Check the level in the reservoir monthly. If weather conditions cause you to use the washers frequently, check the reservoir each time you stop for fuel. See page 125. Tires - Check the tire pressure monthly. Examine the tread for wear and foreign objects. See page 138.

Maintenance

BRAKE FLUID (Gray cap)

ENGINE OIL FILLER CAP

COOLANT RESERVOIR

AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loop)

Fluid Locations

CLUTCH FLUID (Gray cap) (5-Speed Manual Transmission only)

ENGINE OIL DIPSTICK (Orange loop)

ANTI-LOCK BRAKE RESERVOIR (Gray cap) (For cars equipped with ABS)

POWER STEERING FLUID (Red cap)

WASHER FLUID (Blue cap)

Maintenance

Engine Oil

Adding Oil To add oil, unscrew and remove the engine oil fill cap on top of the valve cover. Pour in the oil, and replace the fill cap. Tighten it securely. Wait a few minutes, and recheck the oil level. Do not fill above the upper mark; you could damage the engine.

ENGINE OIL FILL CAP

longevity. Always use a premium-grade detergent oil.

You can determine an oil's SAE viscosity and Service Classification from the API Service label on the oil container.

A fuel-efficient oil is recommended for your Honda. This is shown on the API Service label by the words "Energy Conserving II." This oil is formulated to help your engine use less fuel.

The oil container may also display the API Certification seal. Make sure it says "For Gasoline Engines."

API CERTIFICATION SEAL

Recommended Oil Oil is a major contributor to your engine's performance and

Maintenance

API SERVICE LABEL

requirements given for conventional motor oil: energy conserving, a service classification of SH, and the proper weight as shown on the chart. When using synthetic oil, you must follow the oil and filter change intervals given in the maintenance schedule.

Additives Your Honda does not need any oil additives. Purchasing additives for the engine or transmission will not increase your car's performance or longevity. It only increases the cost of operating your car.

The SAE numbers tell you the oil's viscosity or weight. Select the oil for your car according to this chart.

Ambient Temperature

An oil with a viscosity of 5W-30 is preferred for improved fuel economy and year-round protection in your Honda. You may use a 10W-30 oil if the temperature in your area never goes below 20 °F (-7 °C).

Synthetic Oil You may use a synthetic motor oil if it meets the same

Engine Oil

Changing the Oil and Filter Always change the oil and filter according to the time and distance (miles/kilometers) recommendations on the maintenance schedule. The oil and filter collect contaminants that can damage your engine if they are not removed regularly.

Changing the oil and filter requires special tools and access from underneath the car. The car should be raised on a service station-type hydraulic lift for this service. Unless you have the knowledge and proper equipment, you should have this maintenance done by a skilled mechanic. 1. Run the engine until it reaches normal operating temperature, and then shut it off.

continued

Maintenance

Engine Oil

2. Open the hood, and remove

the oil fill cap. Remove the oil drain bolt and washer from the bottom of the engine. Drain the oil into an appropriate container.

3. Remove the oil filter, and let

the remaining oil drain. A special wrench (available from your Honda dealer) is required to remove the filter.

OIL FILTER WRENCH

DRAIN BOLT WASHER

Maintenance

OIL FILTER

4. Install a new oil filter

according to the instructions that come with it.

5.

6.

Put a new washer on the drain bolt with the flat side toward the engine, and then reinstall the drain bolt. Tighten it to 33 Ib-ft (4.5 kg-m, 44 N.m).

Refill the engine with the recommended oil. Engine oil capacity (including filter): LX 4.0 U.S. qt (3.8 ) EX 4.5 U.S. qt (4.3 )

7. Replace the oil fill cap. Start

the engine. The indicator light should go out within five seconds. If it does not, turn off the engine and inspect your work.

8.

Let the engine run for several minutes; then, check the drain bolt and washer and the oil filter for leaks.

9. Turn off the engine, and wait

for several minutes; then, check the oil level. If necessary, add oil to bring the level to the upper mark on the dipstick.

NOTICE If you change your own oil, please dispose of the used oil properly. Put it in a sealed container, and take it to a recycling center. Do not discard it in a waste bin or dump it on the ground.

Engine Oil, Cooling System

Adding Engine Coolant If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks. This coolant should always be a mixture of 50
percent antifreeze and 50 percent water. Never add straight antifreeze or plain water.

RESERVE TANK

Always use Genuine Honda Antifreeze/Coolant. The cooling system contains many aluminum components that can corrode if an improper antifreeze is used. Some antifreeze, even though labeled as safe for aluminum parts, may not provide adequate protection.

If the reserve tank is completely empty, you should also check the coolant level in the radiator.

MAX

MIN

Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

continued

Maintenance

Cooling System

1. Make sure the engine and

radiator are cool.

2. Turn the radiator cap

counterclockwise, without pressing down on it, until it stops. This relieves any pressure remaining in the cooling system.

RADIATOR CAP

3. Remove the radiator cap by

pushing down and turning counterclockwise.

Maintenance

4. The coolant level should be

up to the base of the filler neck. Add coolant if it is low.

RESERVE TANK

5. Put the radiator cap back on.

Tighten it fully.

6. Pour coolant into the reserve

tank. Fill it to halfway between the MAX and MIN marks. Put the cap back on the reserve tank.

Do not add any rust inhibitors or other additives to your car's cooling system. They may not be compatible with the coolant or engine components.

Replacing Engine Coolant The cooling system should be completely drained and refilled with new coolant according to the time and mileage recommendations in the maintenance schedule. Only use the recommended antifreeze.

Draining the coolant requires access to the underside of the car. Unless you have the tools and knowledge, you should have this maintenance done by a skilled mechanic.

drain bolt from the engine block.

1. Turn the heater temperature

control lever to maximum heat. Open the hood. Make sure the engine and radiator are cool to the touch.

2. Remove the radiator cap.

RADIATOR CAP

DRAIN PLUG

3. Loosen the drain plug in the bottom of the radiator. The coolant will drain through the splash guard. Remove the

DRAIN BOLT

Cooling System

4. Remove the reserve tank

from its holder by pulling it straight up. Drain the coolant, and then put the tank back in its holder.

RESERVE TANK

HOLDER

RESERVE TANK CAP

5. When the coolant stops

draining, tighten the drain plug in the bottom of the radiator. Apply non-hardening sealant to the drain bolt threads, and reinstall the bolt in the engine block. Tighten the bolt to 61 Ib-ft (8.5 kg-m, 83
N.m).

continued

Maintenance

Cooling System

6. Mix the recommended

antifreeze with an equal amount of purified or distilled water in a clean container. The cooling system capacity is: With 5-speed manual transmission: 5.7 U.S. qt (5.4 ) With automatic transmission: 5.6 US. qt.(5.3 )

7. Pour coolant into the radiator

up to the base of the filler neck.

8. Loosen the bleeder bolt on top of the engine. Tighten it again when coolant comes out in a steady stream with no bubbles.

the engine, and let it run until it warms up (the radiator cooling fan comes on at least twice).

10. Turn off the engine. Check

the level in the radiator, and add coolant if needed. Install the radiator cap, and tighten it fully.

11. Fill the reserve tank to the

MAX mark. Install the reserve tank cap.

RESERVE TANK

9. Refill the radiator to the base of the filler neck. Put the cap on the radiator, and tighten it only to the first stop. Start

Maintenance

Windshield Washers, Transmission Fluid

Windshield Washers Check the level in the windshield washer reservoir at least monthly during normal usage. In bad weather, when you use the washers often, check the level every time you stop for fuel. The windshield washer reservoir is located behind the driver's side headlight. Check the reservoir's fluid level by removing the cap and looking at the dipstick.

Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather.

NOTICE Do not use engine antifreeze or a vinegar/water solution in the windshield washer reservoir.

Antifreeze can damage your car's paint, while a vinegar/water solution can damage the windshield washer pump.

Use only commercially available windshield washer fluid.

Transmission Fluid Automatic Transmission Check the fluid level with the engine at normal operating temperature.

1. Park the car on level ground.

Shut off the engine.

2. Remove the dipstick (yellow loop) from the transmission, and wipe it with a clean cloth.

LEVEL GAUGE

DIPSTICK

continued

Maintenance

Transmission Fluid

3. insert the dipstick all the way

into the transmission securely as shown in the illustration.

4. Remove the dipstick and

check the fluid level. It should be between the upper and lower marks.

UPPER MARK LOWER MARK

5.

If the level is below the lower mark, add fluid into the tube to bring it to the upper mark. Use Honda Premium Formula

Maintenance

6.

Automatic Transmission Fluid or an equivalent DEXRON II Automatic Transmission Fluid (ATF) only. Insert the dipstick all the way back in the transmission. Make sure that the notch fits in the dipstick guide and the dipstick is all the way down.

The transmission should be drained and refilled with new fluid according to the time and distance recommendations in the Maintenance Schedules.

5-Speed Manual Transmission Check the fluid level with the transmission at normal operating temperature and the vehicle sitting on level ground. Remove the transmission filler bolt and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the

bolt hole. If it is not, add Honda Manual Transmission Fluid until it starts to run out of the hole. Reinstall the filler bolt and tighten it securely.

CORRECT LEVEL

FILLER BOLT

If Honda MTF is not available, you may use an SG or SH-rated motor oil with a viscosity of 10W-30 or 10W-40 temporarily. Motor oil can cause increased transmission wear and high shifting effort, so you should

have the transmission drained and refilled with Honda MTF as soon as possible.

The transmission should be drained and refilled with new oil according to the time and distance recommendations in the Maintenance Schedules.

Transmission Oil, Brake and Clutch Fluid

Brake and Clutch Fluid Check the fluid level in the reservoirs monthly. There are up to three reservoirs, depending on which model. They are:

Brake fluid reservoir (all models) Clutch fluid reservoir (5-speed manual transmission only) ABS reservoir for cars with ABS option

The brake fluid in the brake and anti-lock brake systems should be replaced every 3 years or 45,000 miles (72,000 km), whichever comes first.

Brake System The fluid level should be between the MIN and MAX marks on the side of the reservoir. If the level is at or below the MIN mark,

your brake system needs attention. Have the brake system inspected for leaks or worn brake pads.

MAX

MIN

If you add brake fluid to bring it up to the MAX mark, use Genuine Honda Brake Fluid or an equivalent from a sealed container that is marked DOT 3
or DOT 4 only. Brake fluid marked DOT 5 is not compatible with your car's braking system.

continued

Maintenance

Brake and Clutch Fluid

Anti-Lock Brake System The fluid should be between the MIN and MAX marks on the side of the reservoir. If it is at or below the MIN mark, it may indicate a problem in ABS. Have the dealer inspect the system and add fluid.

MAX

MIN

Maintenance

If the fluid level is half an inch or more above the MAX mark, it may indicate a problem in the ABS. Have your dealer inspect the system as soon as possible.

If you add brake fluid to bring it up to the MAX mark, use the same DOT 3 or DOT 4 brake fluid specified for the brake system.

Clutch System The fluid level should be between the MIN and MAX marks on the side of the reservoir. If it is not, add brake fluid to bring it up to that level. Use the same DOT 3
or DOT 4 brake fluid specified for the brake system.

MAX

MIN

Low fluid level can indicate a leak in the clutch system. Have this system inspected as soon as possible.

Power Steering You should check the fluid level in the power steering reservoir monthly. Check the level when the engine is cold. Look at the side of the reservoir. The fluid should be between the UPPER LEVEL and LOWER LEVEL. If it is below the LOWER LEVEL, add power steering fluid to the UPPER LEVEL.

UPPER LEVEL

LOWER LEVEL

Power Steering, Air Cleaner Element

NOTICE

Using automatic transmission fluid or another brand of power steering fluid will damage the system. Use only Genuine Honda Power Steering Fluid-V.

A low power steering fluid level can indicate a leak in the system. Check the fluid level frequently and have the system inspected as soon as possible.

NOTICE

Turning the steering wheel to full left or right lock and holding it there can damage the power steering pump.

Air Cleaner Element The air cleaner element should be cleaned or replaced according to the time or distance recommendations in the Maintenance Schedules.

Cleaning (Severe Conditions) Clean the air cleaner element by blowing compressed air through it in the opposite direction to normal air flow. If you do not have access to compressed air (such as a gas station), ask your Honda dealer to do this service.

Follow the replacement procedure for removal and reinstallation.

continued

Maintenance

Air Cleaner Element

Replacement The air cleaner element is inside the air cleaner housing on the passenger's side of the engine compartment. To replace it: 1. Remove the air cleaner duct

by pulling it straight out.

DUCT

2. Loosen the screws from the battery hold-down bracket, and push the bracket away from the air cleaner.

BOLTS

4. Remove the old air cleaner element. Clean the inside of the housing with a damp rag.

AIR CLEANER ELEMENT

HOLD-DOWN BRACKET

HOLD-DOWN BRACKET

3. Loosen the four bolts, and

remove the air cleaner housing cover.

5. Place the new air cleaner

element in the housing.

6. Reinstall the housing cover

and the duct, and tighten the four bolts.

7. Resinstall the battery

hold-down bracket, and tighten the screws.

Maintenance

Spark Plugs

Tightening torque: 13 Ib-ft (1.8 kg-m, 18 N.m).

3. Remove the spark plug with

a 16 mm (5/8 inch) spark plug socket.

4. Put the new spark plug into

the socket; then screw it into the hole. Screw it in by hand so you do not crossthread it.

Spark Plugs The original spark plugs in your car need to be replaced every 2
years or 30,000 miles (48,000
km), whichever comes first.

Replacement 1. Clean up any dirt and oil that

have collected around the spark plug caps.

2. Remove the spark plug cap

by pulling it straight out.

SPARK PLUG CAP

5. Torque the spark plug. (If you do not have a torque wrench, tighten the spark plug two-thirds turn after it contacts the cylinder head.)

NOTICE

Tighten the spark plugs carefully. A spark plug that is too loose can overheat and damage the engine. Overtightening can cause damage to the threads in the cylinder head.

continued

Maintenance

Spark Plugs, Battery

6. Install the spark plug cap. 7. Repeat this procedure for the

other three spark plugs.

Spark Plug Specifications

Normal driving conditions

NGK: Nippondenso: KJ16CR-L11

ZFR5F-11

Hot climates or continuous high speed driving

NGK: Nippondenso: KJ20CR-L11

ZFR6F-11

Spark plug gap 0.039 - 0.043 in. (1.0-1.1 mm)

Battery Check the condition of the battery monthly. You should check for proper electrolyte level and corrosion on the terminals.

Maintenance

The battery contains sulfuric acid (electrolyte) which is highly corrosive and poisonous. Getting electrolyte in your eyes or on your skin can cause serious burns. Wear protective clothing and eye protection when working on or near the battery.

Emergency Procedures Eyes - Flush with water from a cup or other container for at least 15 minutes. (Water under pressure can damage the eye.) Immediately call a physician or911.

Skin - Remove contaminated clothing. Flush the skin with large quantities of water. Call a physician immediately.

Swallowing - Drink water or milk. Call your local Poison Control Center or a physician immediately.

Check the battery condition by looking at the test indicator window on the battery. The label on the battery explains the test indicator's colors.

TEST INDICATOR WINDOW

Check the battery terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When

this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel. Coat the terminals with grease to help prevent future corrosion.

If the terminals are severely corroded, clean them with baking soda and water. Then use a wrench to loosen and remove the cables from the terminals. Always disconnect the negative (-) cable first and reconnect it last.

Clean the battery terminals with a terminal cleaning tool or wire brush. Reconnect and tighten the

cables, and then coat the terminals with grease.

If you need to connect the battery to a charger, disconnect both cables to prevent damage to the car's electrical system.

The battery gives off explosive hydrogen gas during normal operation.

A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.

Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.

Battery

If your car's battery is disconnected or goes dead, the audio system will disable itself. The next time you turn on the radio you will see "Code" in the frequency display. Use the Preset buttons to enter the five-digit code (see page 79).

NOTICE Charging the battery with the cables connected can seriously damage your car's electronic controls. Detach the battery cables before connecting the battery to a charger.

Maintenance

Windshield Wipers

Windshield Wipers Check the condition of the windshield wiper blades at least every six months. Look for signs of cracking in the rubber or areas that are getting hard. Replace the blades if you find these signs, or they leave streaks and unwiped areas when used.

To replace the blade, do this: 1. Raise the wiper arm off the

windshield.

WIPER ARMS

Maintenance

2. Disconnect the blade

assembly from the wiper arm by pushing in the lock tab. Hold it in while you push the blade assembly toward the base of the arm.

3. Remove the blade from its

holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder.

BLADE

4. Examine the new wiper

blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and

Windshield Wipers, Air Conditioning

install them in the slots along the edge of the new blade.

BLADE

REINFORCEMENT

5. Slide the new wiper blade

into the holder until the tabs lock.

6. Slide the new blade assembly

onto the wiper arm. Make sure it locks in place.

7. Lower the wiper arm down

against the windshield.

Air Conditioning System Your car's air conditioning is a sealed system. Any major maintenance, such as recharging, should be done by a qualified technician. You can do a couple of things to make sure the air conditioning works efficiently.

AIR CONDITIONING CONDENSER

Periodically check the engine's radiator and air conditioning condenser for leaves, insects, and dirt stuck to the front

surface. These block the air flow and reduce cooling efficiency. Use a light spray from a hose or a soft brush to remove them.

NOTICE The condenser and radiator fins bend easily. Only use a low- pressure spray or soft-bristle brush to clean them.

Run the air conditioning at least once a week during the cold weather months. Run it for at least 10 minutes while you are driving at a steady speed with the engine at normal operating temperature. This circulates the lubricating oil contained in the refrigerant.

If the air conditioning does not get as cold as before, have your dealer check the system.

continued

Maintenance

Air Conditioning, Drive Belts

Recharge the system with Refrigerant HFC-134a (R-134a). See Specifications on page 179.

NOTICE Whenever you have the air conditioning system serviced, make sure the service facility uses a refrigerant recycling system. This system captures the refrigerant for reuse. Releasing refrigerant into the atmosphere can damage the environment.

Drive Belts Check the condition of the two