1993 Honda Accord Wagon Owners Manual

Download PDF Manual
US Cars The tires on all Honda cars meet Federal Safety Requirements. All tires on to Department of Transportation (DOT) standards for tread wear, traction and temperature. the Accord are also "graded" according Three grades are shown on the tire side wall. TIRE WHEEL RIM Tread Wear The tread wear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one half (1-1/2 ) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate. Traction The traction grades, from highest to lowest, are A, B, and C, and they represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. The traction grades assigned are based on braking (straight ahead) traction tests and do not include cornering (turning) traction. Temperature The temperature grades are A (the highest), B and C representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. The tire temperature grade is established for a tire that is properly inflated and not overloaded. Excessive speed, under- inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. Emission Controls Sources of Emissions The combustion process produces carbon monoxide (CO), oxides of nitrogen (NO ) and hydrocarbons. The evaporation of fuel in the fuel tank also produces hydrocarbons. Control of oxides of nitrogen and hydrocarbons is very important since, under certain conditions, when subjected to sunlight, they react to form photochemical smog. Carbon monoxide does not react to form smog, but it is toxic. The Clean Air Act The Clean Air Act* requires all vehicle manufacturers to explain in writing the operation and maintenance of their emission control systems. Maintenance instructions are included on pages 103-108; the opera- tion of each system is explained below and on the following page. Replacement Parts The emission control systems on your new Honda were designed, built and certified to conform with the Federal regulations implementing the Clean Air Act. Honda recommends only the use of new, Genuine Honda parts or their equivalent. The use of other replacement parts, which are not of equivalent quality, may impair the effectiveness of your car's emission control systems. Evaporative Emission Control System The Evaporative Emission Control System is designed to prevent fuel vapors from escaping into the atmosphere. Fuel vapors from the fuel tank are directed into the charcoal canister where they are adsorbed and stored while the engine is stopped or idling. When the coolant temperature rises to a certain value, the vapors are drawn into the engine through the throttle body and the intake manifold during normal engine operation. *ln Canada, Honda vehicles comply with the Canadian Motor Vehicle Safety Standards (CMVSS) on Emissions valid at the time they are manufactured. Crankcase Emission Control System To prevent crankcase emissions, your car is equipped with a Positive Crankcase Ventilation (PCV) System, which routes blowby gases from the crankcase. through the PCV valve and intake manifold, into the combustion chamber. Engine Exhaust Controls The engine exhaust emission control systems are designed to control combustion during idle, acceleration, cruise, and deceleration. These systems are entirely separate from the crankcase and evaporative emission control systems described previously. PGM-FI System The PGM-FI System on this model is a sequential multiport fuel injection. It consists of three independent subsystems; Air Intake. Electronic Control and Fuel Control, thus allowing more accurate control of air/fuel ratios under all operating conditions. The Electronic Control Module (ECM) detects the amount of air drawn into the cylinders and determines the amount of fuel to be injected to provide the optimum air/fuel ratio for all engine needs. Ignition Timing Control System This system automatically controls the ignition timing to reduce the amount of HC and NO Three-way Catalytic Converter The three-way catalytic converter is used to convert hydrocarbons (HC), carbon monoxide (CO) and oxides of nitrogen (NO ) in the ) and water vapor. exhaust gas, to carbon dioxide (CO ), dinitrogen (N Exhaust Gas Recirculation (EGR) The EGR system is designed to control the formation of oxides of ) caused when nitrogen (NO the fuel mixture burns at high It works by recirculating exhaust gas through the temperature. Exhaust Gas Recirculation valve and into the combustion chambers where it reduces peak temperature by diluting the air/fuel mixture. intake manifold Three-way Catalytic Converter A three-way catalytic converter is installed in the exhaust system to help clean up the harmful exhaust gases that can cause air pollution. To be effective, the converter must work at high temperature, so don't park your car over dry grass, leaves or anything else that could burn easily. To stay effective, the converter must not be contaminated by leaded gasoline; use only unleaded gas as explained on page 84. CATALYTIC CONVERTER CAUTION: The converter can be overheated and damaged if it's fed too much unburned fuel mixture from the engine, so: Don't push or tow the car to start it; it the battery is dead, jump start the car as shown on pages 145-146. Don't turn the key oft while the engine is running above idle speed. Don't change the ignition timing, or remove any emission control parts. Use only the spark plugs specified in this manual. Don't keep driving your car if it isn't running properly, or if its CHARGE warning light or check engine light comes on; have it checked by your Honda dealer. Warranty Service Warranty (US Cars) The following warranties are provided with every new vehicle. 1. New Car Limited Warranty 2. Emissions-Related Defects Warranty 3. Emissions Performance Warranty 4. Original Equipment Battery Limited Warranty 5. Rust Perforation Limited Warranty 6. Accessory Limited Warranty 7. Replacement Parts Limited Warranty 8. Replacement Muffler Lifetime Limited Warranty 9. Seat Belt Limited Warranty 10. Replacement Battery Limited Warranty Your car's original tires are covered by their manufacturer. Tire warranty information is in a separate tire warranty booklet. The details of all warranties pertaining to your car can be found in the Warranty booklet provided with your new car. The required maintenance schedule is contained in this Owner's Manual. If you are unable to obtain warranty service or are dissatisfied with the warranty decision or service you received at an authorized Honda dealership, you should review the matter with that dealership's Service Manager. This will normally resolve your problem. If it does not, you should appeal the decision with the owner of the dealership. Please bear in mind that your problem will likely be resolved in the dealership, using the dealer's facilities, equipment, and personnel. So it is very important that your initial contact be with the dealer or his management. After following these steps, if you wish to have the matter reviewed by American Honda you should contact the Zone Office serving your area, as shown on the map on the inside of the back cover. When contacting American Honda, please provide the Zone Office with the following information: Vehicle Identification Number Servicing Dealer Name and Address Date of Purchase Mileage on Your Car Your Name, Address, and Phone Number Nature of Problem Selling Dealer After a review of the facts, you will be advised of what can be done. (Canada Cars) Please refer to the 1993 Warranty and Maintenance Guide that came with your car. Reporting Safety Defects (US Cars) If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co, Inc. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or American Honda Motor Co., Inc. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in the Washington, D.C. area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C.20590. You can also obtain other information about motor vehicle safety from the Hotline. Index Body Repair, 140 Brake Lamp Monitor Light, 46 Brakes Anti-lock Brakes, 38 Anti-lock Brake System (ABS) Light, 45 Anti-lock Brake Fluid, 120 Brake Failure Light, 43 Brake Fluid, 119 Brake System Design, 118 Brake Wear, 118 Brake Wear Indicators, 119 Lamp Monitor Light, 46 Parking Brake, 57 Parking Brake Light, 43 Break-in Period, 2 Bulb Replacements, 129-130 Specifications, 150 Capacities, 149 Care and Cleaning, 137-139 Cargo, Storing Safely, 30 Cargo Area, 13 Storage Compartments, 13 Tonneau Cover, 13 Cargo Area Light, 54 Certification Label, 151 Chains, Tire, 132 Check Engine Indicator Light (Canada), 44 Child Proof Door Locks, 7 Child Safety, 31 General Guidelines for Restraining Children Under 40 Pounds, 32 Important Safety Reminders, 32 Air Cleaner Element, 123 Air Conditioning Care, 135-136 Operation, 65 Recycled Refrigerant, 136 Air Pressure, Tires, 131 Airbag (SRS), 24 - 27 Aluminum Alloy Wheels, 138 Antenna, 72 Anti-lock Brake System (ABS) Light, 45 Anti-lock Brakes, 38 Anti-lock Brake Fluid, 120 Anti-theft Steering Column Lock, 88 Antifreeze. See "Radiator Coolant" Appearance Care, 137 Ashtrays, 61 Audio System, 72 Automatic Transmission Driving Technique, 96 Fluid, 114 Operation, 95 Shift Lever Position Indicator, 94 Battery Charging System Light, 44 Jump Starling, 145 Maintenance, 126 Specifications, 150 Beeper System Fasten Seat Belt Beeper, 17 Key Reminder, 88 Light Reminder Chime, 52 Beverage Holder, 60 Index (cont'd) Restraining a Child Who Weighs Between 20 and 40 Pounds, 34 Restraining a Child Who Weighs Over 40 Pounds, 35 Restraining an Infant Who Weighs Less than 20 Pounds, 33 Storing a Child Seat, 37 Using a Seat Belt Locking Clip, 36 Using Child Restraints With Tethers, 37 Where Should Children Sit? 31 Cigarette Lighter, 61 Clock, 59 Clutch Fluid, 121 Coolant Temperature Gauge, 41 Cooling (with A/C), 66 Cooling System, 115-117 Crankcase Emission Control System, 155 Cruise Control Indicator, 42 To Cancel the Cruise Control, 56 To Set the Cruise Control, 55 D4 Indicator Light, 42 - 46 Daytime Running Lights (DRL), 54 DRL Indicator Light, 45 Defrost Defog, 68 Dimensions, Specifications, 149 Doors Child Proof Door Lock, 7 Locks, 6 Power Door Locks, 6 Warning Lights, 46 Emergency Changing a Flat Tire, 141 -144 Hazard Warning System, 53 It Your Car Gets Stuck, 148 Indicator Lights, 42 - 45 Jump Starting, 145 Towing, 147 Emission Controls, 154 - 155 Engine Coolant, 115 Coolant Temperature Gauge, 41 Exhaust Controls, 155 Identification Number, 151 Low-oil Pressure Light, 43 Oil and Filter, 110-112 Specifications, 150 Engine Exhaust Gas Warning, 91 Evaporative Emission Control System, 154 Exhaust Gas Recirculation (EGR), 155 Exterior Care, 137-138 Aluminum Alloy Wheels, 138 Preventive Service (Rust), 139 Rust Prevention, 138 Washing, 137 Waxing, 138 Filters Air, 123 Engine Oil, 111 Fuel, 123 Fluid. See "Oil" Foreign Countries. Operation in, 85 Fuel Filter, 123 Fuel Fill Door and Cap, 86 Gasohol, 84 Gauge, 40 Low Fuel Light, 43 Oxygenated Fuels, 84 Requirement, 84 Fuse Checking and Replacing, 127-128 Specifications, 150 Gas Station Information, back cover Gasoline, 84 Gauges, 40 - 41 Glove Box, 59 Hazard Warning System, 53 Head Restraints, 9 Headlights Flasher, 52 High Beam Indicator Light, 42, 52 High/Low Beam Switch, 52 Reminder Chime, 52 Switch, 52 Heating, 67 Hood, 57 Hood Latch, 57 Identification Numbers, 151 Ignition Switch Anti-theft Lock, 88 Daytime Running Lights (DRL), 54, 88 Key, 88 Light, 53 Reminder Beeper (Key), 88 Indicator Lights, 42- 46 Inflation Pressure, Tires, 131 Instrument Panel, 39 Interior Lights, 54 Interior Trim Care, 137 Jack, 141 - 143 Jump Starting, 145-146 Keyless Entry System, 3 Keys Automatic Shift Lock, 94 Glove Box, 59 Ignition, 88 Keyless Entry System, 3 Reminder Beeper, 88 Remote Access Key, 3 Using the, 3 Tailgate, 3, 4 Lap/Shoulder Belts, See "Seat Belts" Lights Anti-lock Brake System (ABS) Light, 45 Bulb Replacement, 129 -130 Cargo Area Light, 54 Daytime Running Lights (DRL), 54 DRL Indicator Light, 45 Fuse Replacement, 127 Hazard Warning System, 53 Headlight Switch, 52 Index (cont'd) Ignition Switch, 53 Indicator Lights, 42 - 46 Interior Lights, 54 Light Reminder Chime, 52 Operation of, 52 - 54 Turn Signals, 52 Loading the Car, 12 Lockout Prevention, 7 Locks Anti-theft Steering Column Lock, 88 Child Proof Door Locks, 7 Door, 6 Fuel Fill Door, 86 Glove Box, 59 Lockout Prevention, 7 Power Door Locks, 6 Tailgate, 4 Plunger, 6 Using Power Door Locks, 6 Using Remote Access Key, 3 Lumbar Support, 8 Maintenance Record, 106 Schedule, 103-105 Maintenance Indicator, 47 Malfunction Indicator Lamp (US), 44 Manual Transmission Maximum Allowable Speed, 93 Oil, 113 - 114 Recommended Shift Speeds, 93 Shifting, 92 Meters, Gauges. See "Gauges" Mirrors Power Mirrors, 51 Rearview Mirrors, 51 Moonroof If the Moonroof Won't Close, 71 Maintenance, 71 Operation, 70 Sunshade, 70 Numbers, Vehicle Identification, 151 Octane Rating, Gasoline, 84 Occupant Protection System, 15 Odometer, 40 Oil Clutch Fluid, 121 Engine Oil, 110- 112 Fluid Locations, 109 Low-oil Pressure Light, 43 Power Steering Fluid, 122 Transmission Oil/Fluid, 114 Operation in Foreign Countries, 85 Panel Brightness Control, 53 Parking Brake, 57 Parking Brake/Brake Failure Light, 43 Pets, Driving With, 30 Power Door Locks, 6 Mirrors, 51 Steering, 122 Windows, 58 Pregnant Women, 23 Pressures, Tire Inflation, 131 Preventive Service, 139 Radiator, Coolant, 115 - 117 Radio Operation, 72, 74 Rear Seat Arm Rest, 9 Rear Window Defogger, 50 Remote Access Key, 3 Using the, 3 Glove Box, 59 Tailgate, 3 Replacement Air Cleaner Element, 123 Bulbs, 129 - 130 Engine Oil, 111 Fuel Filter, 123 Oil Filter, 112 Radiator Coolant, 116 - 117 Spark Plugs, 124 Tires, 133 Wiper Blades, 125 Rearview Mirrors, 51 Rust Prevention, 138 Safety Defects, Reporting, 158 Safety Information, 20 - 30 Door Locks, 30 Driving With Pets, 30 Head Restraint Position, 29 Seat Back Position, 29 Storing Cargo Safely, 30 Safety Items, 90 Seat Belts, 16 - 23 Child Restraint, 32 - 35 Fasten Seat Belt Beeper, 17 Important Safety Reminders, 16 Lap Belt, 18 Wearing the, 21 - 22 Lap/Shoulder Belt, 17 Wearing a, 19 - 21 Maintenance, 23 Pregnant Women, 23 Replacement, 23 Seat Belt Warning Light, 43 Shoulder Anchor Height Adjusting Mechanism, 20 System Components, 17 Wearing Seat Belts Properly, 18 Why Wear Seat Belts, 16 Seats Driver's Lumbar Support, 8 Folding Rear Seat, 10 Front Seat, 8 Head Restraints, 9 Rear Seat Arm Rest, 9 Shift Lever Position Indicator, 42 Shifting 5-Speed Manual Transmission, 92 Automatic Transmission, 94 Spare Tire, 133 Changing a Flat Tire, 141, 144 Specifications, 149 Spark Plugs, 124 Specifications, 149 - 150 Speedometer, 40 SRS Indicator Light, 45 Starting the Engine, 89 Steering Anti-theft Column Lock, 88 Power Steering, 122 Tilt Steering, 48 Stereo Sound System, Operation, 72 Storage Compartments, 13 Stuck Car, 148 Sunshade, 70 Supplemental Restraint System (SRS), 24 - 27 Warranty Service, 157 Washer Rear Window Washer, 49 Reservoir Capacity, 50 Windshield Washer, 49 Washing, 137 Waxing, 138 Wheels, 138 Windows Appearance Care, 137 Power Windows, 58 Windshield Defogger, 50 Windshield Washer, 49 Windshield Wipers, 49 Wipers Blades, 125 Rear Window Wiper, 49 Windshield Wipers, 49 Index (cont'd) Tachometer, 40 Tailgate, 4 - 7 Tape Operation, 77 Temperature Gauge, Coolant, 41 Three-way Catalytic Converter, 155, 156 Tilt Steering, 48 Tire Air Pressure, 131 Balancing, 134 Chains, 132 Changing a Flat Tire, 141 DOT Tire Quality Grades, 152 - 153 Inflation Pressure, 131 Requirement, 152 Rotation, 134 Snow Tires, 132 Spare Tire, 133 Specifications, 149 Tonneau Cover, 13 Tools, 141 Towing, 147 Towing a Trailer, 97 - 102 Transmission Capacity, 149 Identification Number, 151 Oil/Fluid, 113 Shifting the Automatic, 94 - 96 Shifting the Manual, 92 - 93 Tread Wear, 152 Trip Meter, 40 Turn Signals, 42, 52 Vehicle Identification Number, 151 Ventilation, 62 Gas Station Information Gasoline: UNLEADED only Pump octane of 86 or higher Fuel Tank Capacity: 17.0 US gal (64.5 ,14.2 Imp gal) Reserve Capacity: 2.6 US gal (10.0 Tire Information: See label on driver's doorjamb. Hood Release: Pull handle under left side of dash. Engine Oil: Use "Energy Conserving II" SG grade oil. 5W-30 preferred (see pages 110-111 for viscosity recommendations). Capacity (Including filter): 4.0 US qt (3.8 Manual Transmission Oil: , 1.8 Imp gal) , 3.3 Imp qt) Use SF or SG grade oil. 10W-30 or 10W-40 preferred (see pages 113-114 for complete viscosity recommendations). Capacity (Including differential): 2.0 US qt (1.9 ,1.7 lmp qt) Automatic Transmission Fluid: Automatic Transmission Fluid: Honda Premium Formula Automatic Transmission Fluid or an equivalent DEXRON® II type Automatic Transmission Fluid (ATF). Capacity (Including differential): 2.5 US qt (2.4 ,2.1 Imp qt) Power Steering Fluid: Use only Honda power steering fluid: Do not use ATF or any other brand of power steering fluid because it will damage the system. AMERICAN HONDA MOTOR CO., INC. 1919 Torrance Blvd., Torrance, CA 90501-2746 HONDA CANADA INC. 715 MILNER AVE. SCARBOROUGH, ONTARIO M1B2K8 1992 American Honda Motor Co., Inc. - All Rights Reserved. 31SM5630 00X31-SM5-6300 15509305P Printed in U.S.A. 1993 Accord Wagon Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com. Contents Owner's Identification Form Features & Safety ............................................................................................................................... 2 What you should know before driving your car. Starting & Driving............................................................................................................................. What gas to use, how to change gears, etc. Maintenance ....................................................................................................................................... 103 The Required Maintenance Schedule and some items you can service. Emergency Service .......................................................................................................................... Changing a flat, jump starting, towing. Specifications ................................................................................................................................... 149 Dimensions, weights and capacities. Consumer Information .................................................................................................................... 151 Reporting Safety Detects, warranty service, vehicle identification numbers, etc. Index ................................................................................................................................................ Gas Station Information 159 141 84 Introduction This manual contains important information about the safe operation and maintenance of your car. We urge you to read this manual carefully, become familiar with the controls it describes, and follow its recommendations, to help make your driving trouble free and enjoyable. Statements or labels on the product preceded by the following words are of special significance: indicates severe personal injury or death will result if instructions are not followed. indicates a strong possibility of severe personal injury or death if instructions are not followed. means hazards or unsafe practices which could cause minor personal injury or product or property damage. NOTE: gives helpful information. Break-in Period During the first 600 miles (1,000 km) of driving, avoid full-throttle starts and cruising for extended periods at a constant speed. NOTE: This break-in procedure also applies to exchanged or overhauled engines. During and after the break-in period, drive the car at moderate speeds until the engine is fully warmed up. During the first 200 miles (300 km), try to avoid severe braking. Brake misuse during this period will reduce future braking efficiency. Remember, your Honda Automobile dealer knows your car best and should be consulted for service assistance and advice. Keys and Locks Remote Access Key (US: EX, Canada: EX-R) Your car is supplied with a battery-operated remote access key. The battery in the remote access key recharges whenever the key is in the ON (I I) position in the ignition. Use the remote access key as your main ignition key. This will allow the battery to be regularly recharged. Keyless Entry System (US: EX, Canada: EX-R) Use the remote access key to activate the keyless entry system. The keyless entry system enables you to operate the locks from outside the car without inserting the key in the keyhole. locks the door Using the Remote Access Key (US: EX, Canada: EX-R) To operate from outside the car using the remote access key, aim the key blade at the keyless entry window located to the left of the keyhole in the driver's door or tailgate, and press the button in the key. Keep the key blade within 18 inches (50 cm) and in line with the keyless entry window. When the remote access key is used on the driver's door, all doors and the tailgate will lock; but only the driver's door will unlock. If the remote access key is used on the tailgate, the tailgate and all doors will lock and unlock. KEYLESS ENTRY WINDOW KEYLESS ENTRY WINDOW Keys and Locks (cont'd) Master and Valet Keys (All Models) Your car is supplied with a master key that fits the ignition and all locks, and a valet key that fits the ignition and doors, but not the glove box or tailgate. The valet key is provided for times when you must leave the key with a parking attendant or repair person, but still want safely locked-up in the glove box. valuables keep to VALET KEY MASTER KEY Write down the numbers stamped on all of the keys and keep the information in your wallet or purse in case you ever need to have duplicates made. All keys are double-edged so you can insert them into the locks with either side up. Locking and Unlocking If a key is used to lock the driver's side door, all doors and the tailgate will lock, but the key will only unlock the driver's door. If a key is used in the front passenger door lock, all doors and the tailgate will lock and unlock. Using the key in the tailgate lock will lock and unlock the tailgate and all doors. To open the tailgate, pull the handle, then lift up. Lock Unlock Unlock Lock Care of the Remote Access Key (US: EX, Canada: EX-R) The electronics in your remote access key are sensitive and can be damaged by rough handling. Once a remote access key is damaged, it will not work. Keep the key out of direct sunlight and areas of high temperature, or high humidity. Avoid dropping the key or placing heavy objects on the key. This key should not be disassembled. Keep the key away from water. If the key gets wet. carefully wipe it with a soft cloth. Operating Problems If the remote access key does not work, do not try to disassemble it. Check for moisture on the key or dirt on the keyless entry window. Carefully wipe up any damp or soiled areas with a soft cloth. The key's battery may be discharged from lack of use. The battery in the key will recharge after 15 minutes of driving. Replacement Key If you lose or damage your remote access key, you can order a replacement from your Honda dealer Inside the key are some expensive electronic parts, therefore replacement can be costly. You will need the five-digit code number on the aluminum plate that came with your key. You will also need the four-digit number on the key blade. Keep these numbers stored in a safe but accessible place. Keys and Locks (cont'd) Door Plunger From inside the car, each door and the tailgate can be locked by pushing the plunger down; each door can be unlocked by pulling the plunger up. Pushing down the plunger on the driver's door locks all doors and the tailgate, but pulling up the plunger unlocks only the driver's door. Pushing down on the tailgate plunger locks the tailgate and all doors. The plunger on the tailgate is not designed to be pulled up manually for unlocking. Unlock Lock Unlock Lock Power Door Locks All doors and the tailgate can be simultaneously locked and unlocked by operating the master door lock switch on the inside of each front door. Unlock Lock Lockout Prevention Lockout Prevention keeps you from locking the driver's door or the tailgate when the key is in the ignition and the driver's door or tailgate is open. If you try to lock the driver's door by pushing down the plunger, the tailgate plunger and all other door plungers will pop back up. If you push down the tailgate plunger when the key is in the ignition and the tailgate is open, the tailgate plunger and all other door plungers will pop back up. Also, both master door lock switches will not lock the doors if either front door is open and the key is in the ignition. The system can be overridden if the outside or inside door handle is held in the open position while the plunger is pushed down. The lock cycles several times and may lock all doors and the tailgate after the door is closed . Lockout Prevention does not affect the operation of any passenger door lock. (US: EX, Canada: EX-R) Lockout Prevention does not affect the operation of the Remote Access Key. Child Proof Door Locks The child proof door locks are designed to prevent accidental opening of the rear doors from inside the car. To activate the locks, push down the lock tabs located on each rear door, then close the doors. When the rear doors are locked in this way, they can only be opened from the outside. LOCK TAB Lock Seats Front Seat Adjust the seat position by pulling up on the adjustment lever under the front edge of the seat cushion and sliding the seat to the desired position. Then release the lever and make sure the seat is locked in position by moving it back and forth. Pull up Pull up The angle of the seat-back can be changed by pulling up on the lever at the outside edge of the seat and leaning forward or back. Release the lever and let the seat lock into place when it reaches the desired angle. Seat belts are most effective when the driver and passengers are sitting up straight and well back in each seat. Do not adjust the driver's seat while the car is moving; the seat could move suddenly, causing loss of vehicle control. To reduce the risk of sliding under the seat belts in a collision, the seat-backs should be upright and you should sit well back in the seat. Driver's Lumbar Support (US: EX, CANADA: EX-R) To adjust for more or less support of the driver's lower seat-back cushion, turn the knob on the inner side of the seat-back. Do not try to adjust the lumbar support while driving. Make the adjustment while sitting in your normal driving position before driving away. Head Restraints The head restraints are designed to help reduce injuries due to whiplash. They are located at the top of each seat-back and have several height positions. The restraints can be adjusted by pulling up to the recommended position. To lower them, slide the button next to the restraint's height adjustment bar while pushing the restraint down. Adjust so the top of the restraint is approximately level with the tops of your ears. If a head restraint must be removed (for cleaning, fabric repair, etc.) pull the restraint up to its highest position, then slide the button while pulling the restraint out. To reinstall, reverse the above procedure. Slide Do not drive the car with head restraints removed. Do not try to adjust head restraints while driving. Rear Seat Arm Rest The rear seat arm rest located at the rear seat-back can be used by pulling the tab. Seats (cont'd) Folding Rear Seat Each rear seat-back can be folded down to provide more cargo space. Folding both rear seat-backs down will provide maximum cargo space. 1. Pull on the strap at the center of the seat to lift up the seat cushion. STRAP 2. Remove the head restraint from the rear seat-back by sliding the button next to the head restraint's height adjustment bar and lifting the head restraint out. Slide 3. Pull up the release knob at the top of the seat-back and fold the seat forward. Pull up 4. Store the head restraint in the holes provided in the seat cushion. Weight limits shown on the label attached to the driver's doorjamb must be observed. The total weight of passengers and cargo must not exceed the total weight limit on the label. Make sure the rear seat-back latches engage securely when the seat-back is returned to its normal position. Always replace the head restraints when the seat-back is returned to its upright position. When transporting luggage or other cargo do not pile it higher than the front seats. This precaution will help prevent such items from becoming dangerous projectiles in an accident. Cargo weight should be distributed as far forward as possible for better vehicle handling. Loading the Car The maximum your car can carry, including passengers, cargo, and trailer tongue weight, is 950 Ibs (431 kg). This is the Vehicle Capacity Weight noted on the tire label attached to the driver's doorjamb. To calculate the car's load capacity, start with 950 Ibs (431 kg). First subtract 150 Ibs (68 kg) for each person, including the driver. For example, if there will be five people in the car (750 Ibs, 340 kg), you can carry up to 200 Ibs (91 kg) of cargo. If you are towing a trailer, remember to also subtract the trailer tongue weight (see page 97 ) from the 950 Ibs (431 kg) capacity. After you have determined how much cargo you can carry, remember that where you put cargo is also important. Do not load cargo above the top of the rear seat-back. The maximum you can carry behind the rear seat is 200 Ibs (91 kg). To maintain a better weight distribution, place heavier items toward the center of the car. CAUTION: Do not exceed the maximum weight capacity for your car; overloading may affect vehicle handling and tire life. Load cargo so it will not contact the printed defroster wires in the rear window. The wires may be damaged if the cargo rubs against them. Cargo Area A passenger should never sit in the open cargo area while the car is mov- ing. They should sit in one of the seats and wear their seat belt. With the rear seats folded, the length of the cargo area is 72 in. (1850 mm). The width at the tailgate opening is 36 in. (915 mm). The width between the wheel wells is 30 in. (775 mm). The height of the rear opening is 28 in. (725 mm). 28 in. (725 mm) STORAGE COMPARTMENT LOCATIONS Storage Compartments You can store smaller items in any of the three storage compartments in the cargo area. Two compartments are under the carpet, on either side of the tire compart- ment. The third is in the right side panel. Tonneau Cover When extended, the tonneau cover con- ceals your parcels and protects them from direct sunlight. To extend the tonneau cover, pull the cover's leading edge out of its housing and slip the brackets over the hooks provided at both sides of the tail- gate opening. To retract the cover, slip the brackets off the hooks and guide the cover so it rolls back fully into its housing. CAUTION: Do not store parcels on the tonneau cover. The tonneau cover may break if weight is placed on it. TONNEAU COVER Cargo Area (cont'd) Package Net The package net is intended to restrain only light, soft items, such as clothing which do not exceed a total weight of 10 Ibs (4.5 kg). Grasp the net's leading edge and pull it out of the tonneau cover housing. Lock the prongs at both ends of the net into either the floor or ceiling latches. To store the net, release both prongs from the latches and let it roll back into the tonneau cover housing. NET Depress. You can select from either of two locations to position the tonneau cover housing unit. One position is directly behind the rear seat and the other is halfway between the rear seat and the tailgate. To remove the housing unit, depress the latch on the right end of the unit and pull the unit out of the bracket, then pull the op- posite end out of its bracket. CAUTION: Make sure all objects in the cargo area are secured, otherwise they may become projectiles in an accident. HOUSING UNIT LOCATIONS Secure the tonneau cover housing unit when you are not using it. Use the two straps located in the right side floor storage compartment and strap it to the two floor hooks closest to the tailgate opening in the cargo area. If it is not secured, it may be- come a dangerous projectile in an accident. 1. Take one strap and loop the free end through a floor hook. D-RING FLOOR HOOK STORAGE COMPARTMENT 2. Place the housing unit on the strap and wrap the strap completely around it. 3. Slip the free end through the "D" rings, then separate the rings and slip the strap over one ring and under the other and pull tight. Repeat this procedure for the other strap and hook. Your Occupant Protection System Your Accord is equipped with seat belts and other features that work together to protect you and your passengers during a crash. Seat belts are the most important part of your occupant protection system. When worn properly, seat belts can reduce the chance of serious injury or death in a crash. For added protection during a severe frontal collision, your Accord has a Supplemental Restraint System (SRS) with a driver's airbag. Two indicator lights are also part of your safety system. One reminds you to make sure you and your passengers wear your seat belts. The other alerts you to a possible problem with your supplemental restraint system (see page 27). The seats, head restraints, and door locks also play a role in occupant safety. For example, the effectiveness of your seat belt. Head restraints can help protect your neck and head, especially during rear-end impacts. Door locks help keep your doors from being accidentally opened during a crash. To get the maximum protection from your occupant protection system, check the following before you drive away: the seat-back can decrease reclining Everyone in the car is wearing a seat belt properly (see page 18). Infants and small children are properly secured in child safety seats (see page 31). All doors are closed and locked (see page 30). Seat-backs are upright and head restraints are properly adjusted (see page 29). There are no loose items that could be thrown around and hurt someone during a crash or sudden stop (see page 30). By following these guidelines, you can reduce injuries to yourself and your passengers in many crash situations. Remember, however, that no safety system can prevent all injuries or deaths that can occur in severe crashes. The Seat Belt System and How It Works Why Wear Seat Belts Wearing seat belts, and wearing them properly, is fundamental to your safety and the safety of your passengers. During a crash or emergency stop, seat belts can help keep you from being thrown against the inside of the car, against other occupants, or out of the car. Of course, seat belts cannot completely protect you in every crash. But. in most cases, seat belts reduce your chance of serious injury. They can even save your life. That is why many states and all Canadian provinces require you to wear seat belts. Not wearing a seat belt increases the chance of being killed or seriously hurt in a crash. Be sure you and your passengers always wear seat belts and wear them properly. Important Safety Reminders Seat belts are designed for adults and larger children. All infants and small children must be properly restrained in child safety seats (see page 31). A pregnant woman needs to wear a seat belt to protect herself and her unborn child (see page 23). Two people should never use the same seat belt. If they do, they could be very seriously injured in a crash. Do not place the shoulder portion of a lap/shoulder belt under your arm or behind your back. This could increase the chance of serious injuries in a crash. Do not put shoulder belt pads or other accessories on seat belts. They can reduce the effectiveness of the belts and increase the chance of injury. Seat Belt System Components Your Accord has seat belts in all five seating positions. The front seats and the outside positions of the rear seats have lap/shoulder belts. The center position of the rear seat has a lap belt. Your seat belt system also includes a light on the instrument panel to remind you to fasten your seat belt, and to make sure your passengers fasten theirs. This light comes on when you turn on the ignition if you have not fastened your seat belt. A beeper also sounds for several seconds (see page 43). The following pages cover more about the seat belt components and how they work. Lap/Shoulder Belt This style of seat belt has a single belt that goes over your shoulder, across your chest, and across your hips. Each lap/shoulder belt has an emergency locking retractor. In normal driving, the retractor lets you move freely in your seat while it keeps some tension on the belt. During a collision or sudden stop, the retractor automatically locks the belt to help restrain your body. SHOULDER PORTION LATCH PLATE BUCKLE UPPER SEAT BELT ANCHOR To retractor LAP PORTION The Seat Belt System & How It Works (cont'd) Lap Belt The lap belt has one manually-adjusted belt that fits across the hips. It is similar to safety belts used in airplanes. LATCH PLATE BUCKLE Wearing Seat Belts Properly You can increase the effectiveness of your seat belts if you take a little time to read the following pages and make sure you know how to wear seat belts properly. Not wearing a seat belt properly increases the chance of serious injury or death in a crash. Be sure you and your passengers always wear seat belts and wear them properly. Wearing a Lap/Shoulder Belt Before putting on a front seat belt, be sure your seat is adjusted forward or backward to a good driving or riding position and the back of your seat is upright (see page 29). 1. Pull the latch plate across your body and insert it into the buckle. Tug on the belt to make sure the latch is securely locked. 2. Check that the belt is not twisted. 3. Position the lap portion of the belt as low as possible across your hips, not across your stomach. This lets your strong pelvic bones take the force of a crash. The Seat Belt System & How It Works (cont'd) 4. Pull up on the shoulder part of the belt to remove any slack. Make sure the belt goes over your collarbone and across your chest. 5. If the belt crosses your neck, you need to adjust the belt anchor height or your seating position. Front seats: Adjust the belt anchor by squeezing the two buttons and sliding the anchor up or down (it has four positions). Rear seat: Move toward the center of the seat until the belt fits over your collarbone. RELEASE BUTTON RELEASE BUTTON To unlatch the seat belt, push the red PRESS button on the buckle. Guide the belt across your body to the door pillar. If the belt doesn't retract easily, pull it out and check for twists or kinks. Wearing The Lap Belt 1. Pull the latch plate across your hips and insert it into the buckle marked CENTER. If the belt is too short, hold the latch plate at a right angle and pull to extend the belt. Insert the latch plate into the buckle. The Seat Belt System & How It Works (cont'd) 2. Position the belt as low as possible across your hips and pelvic bones, not across your stomach. Pull the loose end of the belt to adjust for a snug but comfortable fit. To unlatch the belt, push the red PRESS button on the buckle. Advice For Pregnant Women Protecting the mother is the best way to protect her unborn child. Therefore, a pregnant woman should wear a properly-positioned seat belt whenever she drives or rides in a car. If possible, use a lap/shoulder seat belt, remembering to keep the lap portion as low as possible (see page 19). Each time you have a check-up, ask your doctor if its okay for you to drive and how you should position a lap/shoulder seat belt. Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. Pull out each belt fully and look for frays, cuts, burns, and wear. Check that the latches work smoothly and the lap/shoulder belts retract easily. Any belt not in good condition or not working properly should be replaced. If a seat belt is worn during a crash, have your dealer replace the belt and check the anchors for damage. If your seat belts get dirty, you can use a soft brush to clean them with a mixture of mild soap and warm water. Do not use bleach, dye, or cleaning solvents. They can weaken the belt material. Let the belts air-dry before you use the car. SEAT BELT ANCHOR METAL LOOP Dirt build-up in the metal loops of the seat belt anchors can cause the belts to retract slowly. Wipe the inside of the loops with a clean cloth dampened in mild soap and water. Supplemental Restraint System FRONTAL COLLISION RANGE All Accords are equipped with a Supplemental Restraint System (SRS) to help protect your head and chest during a severe frontal collision. This system does not replace seat belts. It supplements, or adds to, the protection offered by your seat belt. Not wearing a seat belt increases the chance of serious injury or death in a crash, even if you have an airbag. Be sure you and your passengers always wear seat belts and wear them properly. SRS DRIVER'S AIRBAG SENSOR SENSOR SRS CONTROL UNIT The main components in your SRS are: An airbag in the steering wheel for the driver. A diagnostic system that when the ignition is ON (I I) continually monitors the sensors, control unit, airbag activator, and all related wiring. An indicator light to warn you of a possible problem with the system. Emergency power backup in case your car's electrical system is disconnected in a crash. Important Safety Reminder Even with an airbag, you need to wear a seat belt. The reasons are: Airbags only inflate in severe frontal collisions. They offer no protection in rear impacts, side impacts, rollovers, or moderate frontal collisions. An airbag inflates and deflates very quickly. It cannot protect you during any additional impacts that can occur during a crash. A seat belt helps keep you in the proper position when an airbag inflates. An airbag opens with considerable force, and it can hurt you if you are not in the proper position. Supplemental Restraint System (cont'd) How the Airbag Works If you ever have a severe frontal collision, your airbag will instantly inflate to help protect your head and chest. When the airbag inflates, you may hear a fairly loud noise and you might see smoke and powder. This is normal; it is caused by the inflation of the airbag. To do its job, the airbag inflates with considerable force. So, while it can reduce serious injuries and even save your life, the airbag might cause some facial or other abrasions. After the bag completely inflates, it immediately starts deflating so it won't interfere with your visibility, ability to steer, or ability to operate other controls. The airbag is stored in the center of the steering wheel. For safety, do not attach any items to the steering wheel. They could interfere with the proper operation of the airbag. Or, if the airbag inflates, they could be propelled inside the car and hurt someone. How the SRS Indicator Light Works SRS The purpose of the SRS light on your instrument panel is to alert you of a potential problem with your supplemental restraint system. Have the system checked if: The light does not come on when you turn the ignition ON (I I). The light stays on after the engine starts. The light comes on or flashes while you are driving. Supplemental Restraint System (cont'd) System Service Your supplemental restraint system is virtually maintenance free. There are no parts you can safely service. You must have the system serviced by an authorized Honda dealer: If your airbag ever inflates. The bag must be replaced. Do not try to remove or discard the airbag by yourself. This must be done by a Honda dealer. If the SRS indicator light alerts you of a problem. Have the supplemental restraint system checked as soon as possible. Otherwise, your airbag might not inflate when you need it. When the car is 10 years old. Get the system inspected. The production date is on the left rear doorjamb for your convenience. System Service Precautions Do not modify your steering wheel or any other part of the supplemental restraint system. Modifications could make the system ineffective. Do not tamper with the system components or wiring. This could cause the airbag to inflate inadvertently, possibly injuring someone very seriously. Tell anyone who works on your car that you have a supplemental restraint system. Failure to follow the procedures and precautions in the official Honda service manual could result in personal injury or damage to the system. Scrapping an entire car that has an uninflated airbag can be dangerous. Get assistance from a Honda dealer if your car must be scrapped. If you sell your car, please be sure to tell the new owner that the car has a supplemental restraint system. Alert them to the information and precautions in this part of the Owner's Manual. Additional Safety Information Your seat belt and airbag are obviously important parts of your occupant protection system. In addition, you should know that sitting upright, adjusting the head restraints to the proper positions, locking the doors, and stowing things properly can increase your safety and possibly even save your life. Seat-back Position The seat-backs should be in an upright position for you and your passengers to get the most protection from the seat belts. If you recline a seat-back, you reduce the protective capability of your seat belt. The farther a seat-back is reclined, the greater the risk that you will slide under the belt in a severe crash and be very seriously injured. For information on how to adjust the seat-back, see page 8. Head Restraint Position The head restraint can help protect you from whiplash and other injuries. For the best protection, the top of the head rest should be even with the top of your ears, or as high as possible. For instructions on how to adjust the head restraints, see page 9. Additional Safety Information (cont'd) Door Locks It is not safe to leave your car doors unlocked. A passenger, especially a child, could open a door and accidentally fall out. Also, there is a greater chance of being thrown out of the car during a crash when the doors are not locked. Storing Cargo Safely Before you drive, make sure you first securely store or tie down any items that could be thrown around the car and hurt someone, or interfere with your ability to operate the controls. Do not put any items on top of the tonneau cover. They can block your view and they could be thrown about the car in a crash. Be sure to keep compartment doors closed when the car is moving. If a front passenger hits the door of an open glove box, for example, he could injure his knees. Driving With Pets Loose pets can be a hazard while you are driving. An unrestrained pet can interfere with your ability to drive the car. In a crash or sudden stop, loose pets or cages can be thrown around inside the car and hurt you or your passengers. It is also for their safety that pets should be properly restrained in your car. The recommended way to restrain a medium-sized or larger dog is with a special traveling harness. This harness can be secured to the rear seat with a seat belt. Travel harnesses are available at pet stores. A small dog, cat, or other small animal will be safest in a rigid-sided pet carrier. Choose a style that allows you to secure it to the car's seat by routing a seat belt through the carrier's handle. For further information, contact your veterinarian or local animal protection society. Child Safety Child Safety Children depend on adults to protect them. To help make sure we do, every state and Canadian province has laws requiring infants and young children to be properly restrained whenever they ride in a car. An infant or child who is not properly restrained can be killed or seriously injured in a crash. Be sure any child too small for seat belts is properly secured in a child restraint. Where Should Children Sit? According to accident statistics, children of all sizes and ages are safer when they are properly restrained in the rear seat rather than the front seat. We recommend that, whenever possible, you secure your child's infant or toddler seat in the center position of the rear seat with the lap belt. We also recommend that any child who is too large to use an infant or toddler seat ride in one of the outside positions of the rear seat. The child should then wear the lap/shoulder belt properly for protection. Child Safety (cont'd) Important Safety Reminders Never hold a baby or child on your lap when riding in a car. If you are wearing your seat belt, the violent forces created during a crash will tear the child from your arms. The child could be seriously hurt or killed. If you are holding a child and not wearing a seat belt in a crash, you could crush the child against the inside of the car. Never put your seat belt over yourself and a child. During a crash, the belt could press deep into the child, and cause serious internal injuries. Two children should never use the same seat belt. If they do, they could be very seriously injured in a crash. If you are driving with small children in the car, you should use the childproof door locks to prevent them from opening the rear doors (see page 7). General Guidelines for Restraining Children Under 40 Pounds Use an approved child seat. The seat must meet Federal Motor Vehicle Safety Standard 213 (FMVSS-213) or Canadian Motor Vehicle Safety Standards. Look for the manufacturer's statement of compliance on the box and seat. Use a seat of the right size. Make sure the seat fits your child. Check the seat manufacturer's instructions and labels for height and weight limits. Secure the child seat to the car. All approved child seats are designed to be secured in the car seat by the lap belt or the lap belt portion of a lap/shoulder belt. A child whose seat is not properly secured to the car can be endangered in a crash. To properly route a seat belt through a child seat, follow the seat maker's instructions. If you use a lap/shoulder belt, be sure you install a locking clip on the belt (see page 36). Secure the child in the child seat. Make sure the infant or child is firmly secured to the child seat. Use the straps provided, and carefully follow the manufacturer's instructions. Restraining an Infant Who Weighs Less Than 20 Pounds (9kg) An infant up to about 20 pounds (9 kg) must be restrained in an infant seat or a convertible seat designed for a baby. Because infants must ride in a reclining position, be sure the infant seat always faces the REAR of the car as shown. We recommend that, whenever possible, you put the infant seat in the center position of the rear seat and secure it to the car with the lap belt. If you decide to put an infant seat in any other seating position, you must use a locking clip with the car's lap/shoulder belt (see page 36). Child Safety (cont'd) Restraining a Child Who Weighs Between 20 and 40 Pounds (9-18 kg) Toddler seats are designed for children who weigh between 20 and 40 pounds (9-18 kg). The preferred place to put a toddler seat is in the center position of the rear seat. Use the car's lap belt to secure the seat to the car. If you decide to put a toddler seat in any other seating position, you must use a locking clip on the car's lap/shoulder belt (see page 36). Restraining a Child Who Weighs Over 40 Pounds (18 kg) We recommend that, whenever possible, a child who has outgrown a toddler seat ride in one of the outside positions of the rear seat and use a lap/shoulder belt. Put the lap/shoulder belt on your child and check its fit. The shoulder belt should fit over the collarbone and across the chest. The lap belt should sit low on your child's hips, not across the stomach. If the shoulder belt crosses the neck, have your child move toward the center of the rear seat until the belt fits properly. If the belt still crosses the child's neck, you should use a booster seat. Several styles of booster seats are available. We recommend a design that allows the child to use the car's lap/shoulder belt. Whichever style you select, follow the booster seat manufacturer's instructions. Child Safety (cont'd) Using a Seat Belt Locking Clip Always use a seat belt locking clip when you secure a child seat to your car with a lap/shoulder belt. This helps prevent the child seat from shifting position or overturning. A locking clip is usually included with the child seat. If you need a clip, contact the seat's manufacturer or a store that sells child restraints. To install a locking clip, do the following: 1. Place the child restraint in the desired position. Route the the restraint according to the seat lap/shoulder belt through manufacturer's instructions. Insert the latch plate into the buckle. Pull on the shoulder part of the belt to make sure there is no slack in the lap portion. 2. 3. Tightly grasp the belt near the latch plate. Pinch both parts of the belt together so they won't slip through the latch plate. Unbuckle the seat belt. 4. 5. Install the locking clip as shown. Position the clip as close as possible to the latch plate. Insert the latch plate into the buckle. Push and pull on the child seat to verify that it is held firmly in place. If it is not, repeat these steps until the restraint is secure. Using Child Restraints With Tethers Your Honda has three attachment points for tether-style child seats. Remove the cover from the desired attachment point, shown the illustration, then install the tether hardware that came with the child seat. Tighten the bolt to: in 16 lb.ft (22 N.m, 2.2 kg.m) If you are not sure how to install the bracket, have it installed by your Honda dealer. If you need an anchor plate and mounting hardware, you can obtain them by writing to: American Honda Motor Co., Inc. Consumer Affairs 1919 Torrance Blvd. Torrance, CA 90501-2746 Canadian Cars The anchor plate and mounting hardware for a top tether are supplied with the car. When installing, make sure the toothed washer is on the bottom of the bolt. The supplied anchor plate is designed only for mounting a child restraint. Do not use it for any other purpose. TETHER ATTACHMENT POINTS CHILD SEAT ANCHOR PLATE Storing a Child Seat When you are not using an infant seat or other child restraint, either remove it or make sure it is properly secured so it cannot be thrown around the car during a crash. Anti-lock Brake System (ABS) Anti-lock Brakes (US:EX, Canada: EX-R) Your car is equipped with an Anti-lock Braking System (ABS). This system helps you to maintain stopping and steering control. It does this by helping to prevent the wheels from locking up during hard braking. The ABS is always "ON." It requires no special effort or driving technique. You will feel a pulsation in the brake pedal when the ABS activates. Activation varies with the amount of traction your tires have. On dry pavement, you will need to press on the brake pedal very hard before you feel the pedal pulsation, that means the ABS has activated. However, you may feel the ABS activate immediately if you are trying to stop on snow or ice. Under all conditions, the ABS is helping to prevent the wheels from locking during hard braking so you can maintain steering control. You should continue to press on the brake pedal with the same force. You may feel a slight movement of the brake pedal just after you start the engine. This is the ABS working. The ABS is self-checking. If anything goes wrong, the ABS indicator on the instrument panel comes on (see page 45). This means the Anti-lock function of the braking system has shut down. The brakes still work like a conventional system providing normal stopping ability. You should have the dealer inspect your car as soon as possible. The ABS works by comparing the speed of the wheels. When replacing tires, use the same size originally supplied with the car. Tire size and construction can affect wheel speed and may cause the system to work inconsistently. A car with an ABS may require a longer distance to stop on loose or uneven surfaces than an equivalent car without ABS. The ABS cannot make up for road conditions or bad judgment. It is still your responsibility to drive at reasonable speeds for weather and traffic conditions and to leave a margin of safety. CAUTION: Be careful not to damage the wiring or the speed sensors at the back of each wheel when removing mud or snow from the wheel housings. ABS CRUISE CONTROL MASTER SWITCH WIPER/ WASHER SWITCH MOONROOF SWITCH HAZARD WARNING SWITCH Instrument Panel DIGITAL CLOCK REAR WINDOW DEFOGGER SWITCH IGNITION SWITCH COIN BOX FUSE BOX HOOD RELEASE HANDLE TILT STEERING ADJUSTMENT LEVER US Car shown: TACHOMETER SPEEDOMETER FUEL GAUGE ASHTRAY' PANEL BRIGHTNESS CONTROL KNOB HEATING/ COOLING CONTROL PANEL CIGARETTE LIGHTER GLOVE BOX SRS INDICATOR LIGHT ABS INDICATOR LIGHT SHIFT LEVER POSITION INDICATOR (Automatic Trans. only) COOLANT TEMPERATURE GAUGE MAINTENANCE INDICATOR LIGHT TRIP METER MAINTENANCE INDICATOR RESET ODOMETER TRIP METER RESET BUTTON DOOR AND LAMP MONITOR LIGHT Gauges Speedometer US Cars: The speed is indicated in miles per hour (outer scale) and kilometers per hour (inner scale). Canada Cars: The speed is indicated in kilometers per hour (outer scale) and miles per hour (inner scale). Odometer The numbers on the odometer indicate miles (US cars) or kilometers (Canada cars). The odometer registers total distance traveled and serves as your guide for determining when periodic maintenance is due. US Cars: Federal law makes it illegal to alter the odometer of any motor vehicle with the intent to change the number of miles indicated. Trip Meter The numbers on the trip meter indicate miles (US cars) or kilometers (Canada cars). The trip meter can be returned to zero by pushing in the reset button. Use the trip meter to check fuel consumption or distance traveled per trip. Tachometer The tachometer indicates engine speed in revolutions per minute. The beginning of the RED ZONE indicates the maximum allowable engine R.P.M. Do not run the engine with the tachometer indicator needle in the RED ZONE. Fuel Gauge FUEL TANK CAPACITY: Approx. 17.0 US gal (64.5 As a convenience, the gauge continues to show the same fuel level as when the ignition was last on. After refueling, the gauge will slowly change to the new fuel level when the ignition is switched on. When the needle indicates E (empty), a usable reserve of about 1.1 US gal (4 , 0.9 Imp. gal) remains in the tank. , 14.2 Imp. gal) Coolant Temperature Gauge Do not remove the radiator cap when the engine is hot. The coolant is under pressure and may blow out and scald you. This gauge shows the temperature of the engine coolant. During normal operation, the needle should stay in the middle of the white range. Under severe driving conditions, such as hot weather or driving uphill for a long period, the needle may rise toward the upper section of the white range. If the needle reaches the red line at "H" (Hot), pull safely off the road and stop the engine. Wait until the engine is cool and check the coolant level in the reserve tank on the passenger side of the radiator under the hood (see pages 115-116). Indicator Lights US Car Shown: Shift Lever Position Indicator (Automatic Transmission Only) A lighted indicator between the fuel and water temperature gauges shows which gear you have selected. D4 Indicator Light (Automatic Transmission Only) The D4 indicator light in the instrument panel also serves a second function. If the light flashes while driving (in any gear range) it indicates a possible malfunction in the transmission; avoid rapid acceleration and have the transmission checked by an authorized Honda dealer as soon as possible. Turn Signal/Hazard Indicator Lights When the turn signal lever is pushed for left or right turns, the appropriate green indicator arrow on the instrument panel will blink along with the signal. Turning on the hazard warning switch makes all turn signals and both arrows blink (see page 53). Headlight High Beam Indicator Light This blue indicator light will go on whenever the high beams are switched on (see page 52). Canada Cars: It will also go on with a reduced brightness when Daytime Running Lights (DRL) are on (see pages 45 and 54). Cruise Control Indicator Light CRUISE CONTROL When the cruise control system is engaged, this indicator light is on (see page 55). Low Fuel Light If the light glows, it means you have about 2.6 US gal (10.0 , 2.2 Imp. gal) or less fuel remaining and should refuel. US Canada BRAKE Parking Brake/Brake Failure Light Check the brake light every time you start the car. With the parking brake set. the warning light should go on when the ignition switch is turned to the "I I" or "I I I" position. With the parking brake released, the light should go on when the ignition switch is turned to "I I I". If the light goes on at any other time, it means the brake fluid level in the master cylinder reservoir is too low; add fluid (see page 119) and have your dealer check for leaks immediately. Make sure the parking brake is released and the light is off before driving away. Seat Belt Warning Light The seat belt warning light comes on when the ignition switch is turned on and the driver's belt is not fastened. The light will turn off only when the driver's belt is fastened. Low Oil Pressure Light A severe fluctuation in engine oil pressure will cause this light to flash on and off. The low oil pressure light will come on, and remain on, if there is insufficient oil pressure or when the ignition switch is turned on with the engine not running. If the light should come on while driving pull off the road safely and stop the car. When the engine has cooled down, check the oil level, and add oil if necessary (see page 110). Even if the oil level is correct, the engine should be checked by a Honda dealer before the car is driven again. CAUTION: Running the engine while the low oil pressure light is on constantly may cause immediate and severe engine damage. NOTE: The low oil pressure light will only light as a result of low oil pressure. It is not directly an oil level indicator. Indicator Lights (cont'd) Charging System Light The charging system warning light comes on when there is a problem with the electrical charging system or when the ignition switch is turned on with the engine not running. If the light comes on while driving, stop the car, turn off the engine and check the alternator belt for proper tension. With the engine turned off, push down on the middle of the belt as shown; it should have 0.4 - 0.5 in. (10-12 mm) deflection under a force of 22 Ib (98 N). If the engine has been running, some engine components may be hot enough to burn you. Keep hands away from the radiator fan. The fan may start automatically without warning and run for up to 15 minutes, even after the engine is turned off. NOTE: If necessary, have the charging system checked by an authorized Honda dealer. US Canada US: Malfunction Indicator Lamp Canada: Check Engine Indicator Light This light comes on for a couple of seconds each time the ignition is turned on. It will also come on, and remain on, if there is a malfunction in the emission control system. If the light comes on while driving, avoid driving at high speed, and have the system checked by a Honda dealer as soon as possible. SRS Supplemental Restraint System Indicator Light When the key is turned to the "II" position, the SRS indicator light will come on for about six seconds, to show normal system operation, and then turn off. See Supplemental Restraint System section on pages 24 - 27. Canada DRL Daytime Running Lights (DRL) Indicator Light This light comes on when the ignition switch is ON (position 11), the headlight switch OFF and the parking brake set. This indicates that the "Daytime Running Lights" are off. The indicator light goes off when the parking brake is released. If the parking brake is reapplied without switching the ignition off, the indicator light will remain off. See page 54. If the light does not go off when the parking brake is released with the ignition ON, or if it comes on while driving, it indicates a burned out high-beam bulb. Have the bulb checked and replaced by your Honda dealer. A BS Anti-lock Brake System (ABS) Light (US: EX, Canada: EX-R) The ABS warning light will come on, and remain on, if there is a malfunction in the ABS or when the ignition switch is turned on with the engine not running. If the light comes on while driving, stop the car at a safe place and shut off the engine. If the light does not go out or lights again while driving, have the system checked by an authorized Honda dealer as soon as possible. NOTE: The light does not indicate a failure of the normal brake system. The light only indicates a malfunction in the ABS. In such a case, the ABS is automatically shut down but normal braking capability continues. After jump starting the car, there is a possibility that the ABS warning light may come on due to insufficient battery voltage. After the battery is sufficiently recharged and the engine is turned off and restarted, the ABS warning light should indicate that the ABS is OK, by coming on for a few seconds each time the engine is started. If the light remains on after recharging, have it checked by a Honda dealer. Indicator Lights (cont'd) Door and Lamp Monitor Lights Door and Tailgate Monitor Lights If a door or the tailgate is open when the ignition is switched on, the appropriate indicator will light, and stay lit, until the door or tailgate is closed. BRAKE LAMP Brake Lamp Monitor Light If a brake light does not work, the BRAKE LAMP indicator will go on when you push the brake pedal while the ignition is ON; the indicator will stay on until you have the light repaired or replaced. Have the brake lights checked as soon as possible. It is dangerous to drive your car with a problem in either the brake electrical or hydraulic systems; have your dealer check both systems if you suspect brake trouble. Checking the Door and Lamp Monitor Light The door, tailgate, and brake lamp monitor lights should come on for about two seconds when the ignition switch is turned on. If they don't, have the system checked by a Honda dealer. Maintenance Indicator the total mileage of your car approaches When the specified maintenance interval for engine oil and filter change or other required service, the indicator will change from green to yellow. The indicator will change to red if it is not reset before you reach the mileage interval. The indicator marked MAINTENANCE REQUIRED is to be used as a reminder that there are items in addition to the engine oil and filter that require service each 7,500 miles (12,000 km). See the maintenance schedule on page 106. After the maintenance is done, be sure to reset the indicator by inserting the ignition key in the slot. The color of the indicator will change to green and repeat its cycle. Do not reset the maintenance indicator while driving; your hand may impair steering, which can result in an accident. Tilt Steering The steering wheel position can be adjusted to suit the driver's preference. 1. Push the lever located under the dash, on the left side of the steering column, all the way down and hold it while adjusting the steering wheel to the desired position. 2. Hold the steering wheel in the desired position and pull the lever all the way up to lock it in place. Push down Pull up Do not adjust the steering wheel position while driving. After adjusting the steering wheel position, make sure it is securely locked in place by "rocking" it up and down slightly. Windshield Wipers/Washer Windshield Wipers Turn the switch to INT for intermittent operation; LO for low speed operation and HI for high speed operation. In fog or very light rain, push the lever down to the MIST position for temporary high speed operation of the wipers. The wipers will return to the rest position and the motor will shut off as soon as you release the lever. Windshield Washer Pull the wiper switch lever toward you to turn on the washer. The windshield wipers will sweep when the washer is operated. REAR WINDOW WIPER/ WASHER SWITCH WINDSHIELD WIPER SWITCH TURN FOR WINDSHIELD WIPER OPERATION Pull FRONT WASHER OPERATION ONLY PUSH DOWN FOR MIST OPERATION In freezing weather, warm the windshield with the defrosters before using the washer. This will help prevent icing which could seriously impair visibility. Rear Window Wiper/Washer Turn the switch "ON" to activate the rear windshield wiper. To use the wiper and washer, turn and hold the switch one position up from ON. To use only the washer, turn and hold the switch one position down from OFF. The rear window washer uses the same fluid reservoir as the front washer. Rear Washer Only OFF ON Rear Wiper Only Rear Wiper and Washer Windshield Washer Fluid/Defogger Check the washer fluid regularly, especially during bad weather, or whenever the washer has been in frequent use. The float in the neck of the reservoir indicates the fluid level. WINDSHIELD WASHER RESERVOIR CAPACITY: 4.4 US qt (4.2 Use a good quality commercial washer fluid for all-weather cleaning. ,3.7 Imp qt). WASHER FLUID RESERVOIR FLOAT CAUTION: Do not use radiator antifreeze in the windshield washer; it will damage the paint. Do not use a vinegar/water combination in the windshield washer; it will damage the pump. Prolonged operation of the washer without fluid may damage the pump. Rear Window Defogger Push the switch to turn the defogger on or off. The indicator will light when the defogger is on. defogger will The off automatically 25 minutes after it is turned on. turn Push CAUTION: When cleaning the inside of the rear window, be careful not to damage the printed heater wires on the rear window. Wipe the window horizontally along the wires, not up and down. Load cargo so it does not contact the printed heater wires on the rear window. The wires may be damaged if cargo rubs against them. Rearview Mirrors Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust mirror angles before you start driving. The inside mirror has day and night positions.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

1993 Honda Accord Wagon Owners Manual