8. Shut off the engine and recheck the oil level.
NOTE: Please dispose of used motor oil in a manner that is compatible with the environment. We suggest you take it in a sealed container to your local service station for reclamation. Do not throw it in the trash or pour it on the ground.
CAUTION: Used motor oil may cause skin cancer if repeatedly left in contact with the skin for prolonged periods. Although this is unlikely unless you handle used oil on a daily basis, it is still advisable to thoroughly wash your hands with soap and water as soon as possible after handling used oil.
Transmission Oil/Fluid Check
Transmission oil/fluid must be checked with the engine off and the car on level ground.
If the engine has been running, some engine components may be hot enough to burn you. Keep hands away from the radiator fan. The fan may start automatically without warning and run for up to 15 minutes, even after the engine is turned off.
CAUTION: If the oil/fluid level is low, check for possible leaks before adding oil. Do not overfill.
Since the transmission and differential are in the same housing, you are actually checking both oil/fluid levels in one procedure. Change transmission oil/fluid according to the Maintenance Schedule on page 102.
5-Speed Remove the oil filler bolt (beside the right axle). Feel inside the bolt hole with your finger. If the oil is up to the bottom edge of the hole, the oil level is correct. If it is not, slowly add oil until it runs out of the hole, then reinstall the bolt and tighten it securely with a wrench.
OIL CHECK FILLER BOLT
CORRECT LEVEL
5-SPEED TRANSMISSION OIL CHANGE CAPACITY: 1.9
(2.0 US q t, 1.7 Imp qt)
Use only SF or SG grade motor oil when adding or changing transmis- sion oil.
Use the proper viscosity oil for the climate in which you drive:
Ambient Temperature
Automatic The automatic transmission fluid level is checked (with the engine off and the car on level ground) using the dipstick (with the yellow marking) in the right end of the transmission housing. Remove the dipstick and wipe it off.
DIPSTICK
UPPER LOWER
Insert the dipstick and remove it. The fluid level should be between the upper and lower marks. If necessary, add fluid and recheck. Use Honda Premium Formula Automatic Transmission Fluid or an equivalent DEXRON ® II Automatic Transmission Fluid (ATF) only when adding or changing fluid. After checking the fluid level, push the dipstick in securely.
AUTOMATIC TRANSMISSION FLUID CHANGE CAPACITY: 2.4
(2.5 US q t, 2.1 Imp qt)
Cooling System
The engine in your Honda contains a number of aluminum parts. Therefore, it requires an antifreeze/coolant specifically formulated to protect the aluminum parts from corrosion. Failure to use a suitable antifreeze/coolant may seriously shorten the life of the engine as the result of rapid corrosion damage. Some antifreeze/ coolants, although labeled for use in engines containing aluminum, may not provide adequate protection for your engine. Therefore, use only a Honda-recommended antifreeze/coolant. CHECK WITH YOUR AUTHORIZED HONDA DEALER. For best corrosion protection, the mixture of coolant and water must be maintained year-round at 50/50. Concentrations less than 50% coolant may not provide sufficient protection against corrosion and freezing. Concentrations of greater than 60% coolant will impair cooling efficiency and are not recommended. Low- mineral drinking water or distilled water should be mixed with the antifreeze/coolant. Coolant loss should be replenished by a mixture containing the proper concentration of antifreeze and water. Do not mix different antifreeze/coolants. Do not use additional rust inhibitors or anti-rust products, as they may not be compatible with the radiator coolant. ENGINE DAMAGE CAUSED BY IMPROPER COOLANT USAGE IS NOT COVERED BY THE NEW CAR WARRANTY.
Checking Coolant Check the coolant level in the reserve tank when the engine is at normal operating temperature.
If the level is below the MAX
mark, but still visible, add a 50/50
solution of antifreeze and water
to bring it up to MAX.
If there is no coolant in the re-
serve tank, the cooling system
should be checked for leaks and
repaired
if necessary. Coolant
must then be added to the radi-
ator.
RESERVE TANK
Do not remove the radiator cap when the engine is hot; the coolant is under pressure and could severely scald you. Keep hands away from the radiator fan. The fan may start automatically without warning and run for up to 15 minutes, even after the engine is turned off.
CAUTION: Radiator coolant will damage paint. Quickly rinse any spilled coolant from painted surfaces.
Wait until the engine is cool, then turn the radiator cap counterclock- wise until it stops. DO NOT PRESS DOWN WHILE TURNING THE CAP. After any remaining pressure has been relieved, remove the cap by pressing down and again turning it counterclockwise. Add enough coolant to fill the radiator, and reinstall the cap. Be sure to tighten it securely. Fill the reserve tank up to the MAX mark with the engine cold.
Maintenance 1. Check the freeze protection level of the coolant with a hydrome-
ter.
2. Keep the front of the radiator free of dirt and debris. 3. Check hoses and hose clamps regularly.
Replacing Coolant Replace coolant at 36 months or 45,000 miles (72,000 km), which- ever comes first. Thereafter, replace every 2 years or 30,000 miles (48,000 km), whichever comes first.
RADIATOR COOLANT REFILL CAPACITY: including reserve tank 0.6
(0.16 US gal, 0.13 Imp gal)
5-speed transmission 3.0 Automatic transmission 3.5
(0.79 US gal, 0.66 Imp gal) (0.92 US gal, 0.77 Imp gal)
(cont'd)
Cooling System (cont'd)
1. Set the heater temperature control dial/lever to maximum heat. 2. Remove the radiator cap and loosen the drain plug when the
radiator is cool, and drain the radiator.
RADIATOR CAP
BLEED BOLT
DRAIN PLUG
DRAIN BOLT
3. Remove the drain bolt from the rear side of the cylinder block, and drain the engine and heater.
4.Apply non-hardening sealant to the drain bolt threads, then rein- stall the bolt and tighten it se- curely.
5. Tighten the radiator drain plug se-
curely.
6. Mix the recommended antifreeze with an equal amount of low- mineral or distilled water and fill the to maximum, as illustrated.
reservoir
7. Loosen the air bleed bolt in the water outlet, then fill the radiator to the filler neck with the coolant mixture. Tighten the bleed bolt as soon as coolant starts to run out in a steady stream without bub- bles.
Fill to here.
FILLER NECK
Fill to here.
8. With the radiator cap off, start the engine and let it run until warmed up (fan goes on at least twice). Then, if necessary, add more coolant mix to bring the level back up to the filler neck.
9. Put the radiator cap on, then run the engine again and check for
leaks.
Brakes
Brake System Design The diagonally-separated dual serv- ice brake system is designed so half the system will still provide braking action if the other half fails. Stopping the car after losing the brake fluid from half the system will require more pedal pressure and pedal travel than normal. Also, the distance required to stop will be longer using only half the brake system. If the brakes fail suddenly, downshift to a lower gear for increased engine braking, and pull off the road as soon as possible.
It is hazardous to drive your car with a problem in either the brake electrical or hydraulic system; have your dealer check both systems if you suspect brake trouble. Do not ride the brakes. In other words, don't put your foot on the brake pedal unless you intend to brake. This causes excessive brake wear and can damage, or lead to loss of braking effectiveness through overheating. Your brake lights may also confuse drivers behind you. Driving through deep water may affect the brakes. Check their effectiveness by pressing the brake pedal gently. If the car does not slow down at the normal rate, continue gently applying the brakes, while maintaining a safe speed, until they dry out and normal performance returns.
Brake Wear Both front and rear brakes should be inspected for wear at the intervals shown in the Maintenance Schedule on page 102. When the brakes require maintenance, use only genuine Honda replacement parts or their equivalent.
Brake Wear Indicators Your car is equipped with audible brake wear indicators. When the brake pads need to be replaced, the wear indicators will make a "screeching" sound or a high pitch chirp.
NOTE: Due to some driving habits or climates, brakes may "squeal" when you first apply them or when you have them partially applied; this is normal, and does not indicate excessive wear. The wear indicator makes a "screeching" sound while the brakes are applied.
(cont'd)
Brakes (cont'd)
Brake Fluid
Check the fluid level in the brake
reservoir periodically; it should be
between the MAX and MIN marks
on the reservoir.
If the level is near the MIN mark, add
fluid to raise it to the MAX mark. Do
not overfill. Use only brake fluid
manufactured to DOT 3 or DOT 4
specifications
reservoir cap)
from a sealed container. Follow the
manufacturer's instructions printed
on the can.
(see
MAX MIN
NOTE: A low brake fluid level may be an indication of brake pad wear or of brake fluid leakage. You should have your brakes checked if the brake fluid level in the reservoir is low before re-filling it.
CAUTION: The arrow on the reservoir cap must be pointing forward after the cap is installed. Make sure the brake warning switch wiring doesn't get caught between the cap and top edge of the reservoir.
ANTI-LOCK BRAKE FLUID RESERVOIR
Anti-lock Brake Fluid
(US: EX, Canada: EX-R)
Check the fluid level in the Anti-lock
brake reservoir periodically.
To check, drive the car for a few
minutes to equalize fluid pressure in
the system.
The level should be between the
MAX and MIN marks on
the
reservoir. If the level is near the MIN
mark, add fluid to raise it to the
MAX mark.
Do not overfill. Use only brake fluid
manufactured to DOT 3 or DOT 4
specifications from a sealed container.
Follow the manufacturer's instructions printed on the can.
If the level is more than 10 mm (0.4 in) above the MAX mark, it may
indicate a malfunction of ABS. Have an authorized Honda dealer
check the system as soon as possible.
Clutch Fluid (Manual Transmission)
Check the fluid level in the clutch
reservoir periodically; it should be
between the MAX and MIN marks
on the reservoir.
If the level is near the MIN mark, add
fluid to raise it to the MAX mark. Do
not overfill. Use only brake fluid
manufactured to DOT 3 or DOT 4
specifications from a sealed con-
tainer. Follow the manufacturer's in-
structions printed on the can.
CLUTCH FLUID RESERVOIR
NOTE: A low clutch fluid level may be an indication of clutch fluid leakage. You should have your clutch checked if the clutch fluid level in the reservoir is low.
Power Steering
The power steering on your car helps provide easy handling while parking and maneuvering in traffic, without loss of road "feel" at highway speeds. An engine-driven hydraulic pump provides full power assist at low speeds and decreasing assist as the car goes faster.
CAUTION: If the power steering system should fail, or if the engine should stall, the car can still be steered. However, much greater effort will be required, particularly in sharp turns at low speed.
NOTE: You may feel a slight clunk or knock when turning the wheel with the engine off. This is a normal condition due to the design of the system.
RESERVOIR CAP
Power Steering Fluid Check the power steering fluid level with the engine cold and the car parked on level ground. Make sure the fluid level is between the upper and lower marks on the reservoir. If the level has dropped close to or below the lower mark, check for leaks before adding fluid the upper mark. Do not overfill.
to
UPPER
LOWER
CAUTION: Use only genuine Honda power steering fluid. The use of other fluids such as A.T.F. or other manufacturer's power steering fluid will damage the system.
Air and Fuel Filters
Air Filter Replace the air filter every 24 months or 30,000 miles (48,000 km), whichever comes first (more often in extremely dusty conditions). Loosen the attaching bolts, then remove the cover. Remove the air filter and replace it with a new filter. Reinstall the cover and tighten the bolts.
BOLTS
FILTER
Fuel Filters The fuel filter is located in the engine compartment, on the right center of the lower dashboard. It should be replaced at 60,000 miles (96,000 km) or 48 months whichever comes first, or any time you suspect contaminated gas may have clogged it.
Because the fuel system is under pressure, the filter should be replaced only by a qualified Honda technician.
Spark Plugs
Spark plugs should be replaced every 24 months or 30,000 miles (48,000 km), whichever comes first. Recommended spark plugs:
ZFR5F-11 (NGK) KJ16CR-L11 (NIPPONDENSO) (for all normal driving) ZFR6F-11 (NGK) KJ20CR-L11 (NIPPONDENSO) (for hot climates or continuous high speed driving)
Keep hands away from the radiator fan. The fan may start automatically without warning and run for up to 15 minutes, even after the engine is turned off.
CAUTION: Never use spark plugs with an improper heat range; they will adversely affect engine performance and durability.
Replace plugs one at a time, so you don't get the wires mixed up. 1. Clean any dirt from around the spark plug base. 2. Disconnect the plug cap, then remove and discard the old plug. 3. Check the gap of the new spark plug before installation.
Plug gap should be: 1.1 mm (0.04 in)
4. Thread the new spark plug in by hand to prevent cross-threading. 5. After the plug seats against the cylinder head, tighten 1/2 turn
with a spark plug wrench to compress the washer.
6. Reinstall the spark plug cap.
CAUTION: The spark plugs must be securely tightened, but not overtightened. A plug that's too loose can get very hot and possibly damage the engine; one that's too tight could damage the threads in the cylinder head.
Thread in by hand.
PLUG CAP
Wiper Blades
For maximum visibility, replace worn or cracked wiper blades when you notice they do not wipe the windshield cleanly or smoothly.
To Replace Worn-out Blades
1. Detach the blade assembly from the arm by pressing the lock tab in, then pushing the blade toward the base of the arm.
Push
Press Lock Tab in
2. Firmly grasp the end of the blade rubber and pull until the tabs are free of the metal support.
METAL SUPPORT
Pull out
3. Remove the metal retainers from the worn-out blade rubber and put them in a new blade rubber.
TABS
4. Insert the new blade rubber from the opposite side of the blade tabs and position the tabs in the metal support.
RETAINERS
5. Reinstall the blade assembly on
the wiper arm.
Battery
The condition of the battery can be determined by checking the test indicator. Service as required according to the label on the battery. Any corrosion around the positive and negative terminals should be washed off with a solution of baking soda and warm water. Dry the terminals and then coat them with grease.
TERMINAL
TERMINAL
TEST INDICATOR
The battery gives off explosive gases; keep sparks, flames, and cigarettes away. Provide adequate ventilation when charging or using the battery in an enclosed space. The battery contains sulfuric acid (electrolyte). Contact with skin or eyes may cause severe burns. Wear protective clothing and a face shield. — If electrolyte gets on your skin, flush with water. — If electrolyte gets in your eyes, flush with water for at least
15 minutes and call a physician immediately.
Electrolyte is poisonous. — If swallowed, drink large quantities of water or milk and follow with milk of magnesia or vegetable oil and get immediate medical assistance.
KEEP OUT OF REACH OF CHILDREN.
Fuse Replacement
One of the two fuse boxes in your car is located under the dashboard on the driver's side. The circuits protected by each fuse are listed inside the fuse box cover. To open the fuse box, turn the knob as shown.
If any of your car's lights, accessories, or controls don't work, check their fuses. If a fuse has blown, the wire inside it will be burned through.
BLOWN
FUSE REMOVER
Checking the fuses: 1. Turn off the ignition and all other switches. 2. If you find a blown or possibly faulty fuse, use the fuse remover, stored beside the spare fuse to pull the blown fuse out of its clips.
3. Check all other fuses as well as the one you suspect. 4. Push in a new fuse of the same rating, and make sure it fits tightly
in the clips. If it fits loosely, have your dealer fix it. If you don't have a spare, take a fuse of the same rating (or lower) out of a circuit you may not need, like the radio or cigarette lighter. Remember to replace the borrowed fuse and the missing spares.
(cont'd)
Fuse Replacement (cont'd)
CAUTION: A blown fuse may be just a symptom of some other problem. If a new fuse blows right away, the cause should be diagnosed and corrected by a qualified Honda technician. Never replace a fuse with anything but another fuse of the same or lower rating. A higher capacity fuse could cause damage and even start a fire.
The main fuses and some primary fuses are installed in the fuse box on the right front fender in the engine compartment. If the circuits from the battery are ever overloaded (by a short in the system drawing too much current for example), a main fuse will blow preventing damage the entire If the main fuse wiring harness. blows, have a Honda dealer check the system, repair the cause, and replace the fuse.
to
(US:EX, Canada: EX-R) The fuses for Anti-lock Brakes are installed next to the air filter.
CAUTION:
The electrical system is protected by fuses that are designed to fail and prevent damage to the wire harness. Always replace blown fuses with the same rating as specified to prevent wiring damage that can result in a possible fire. For proper electrical contact after replacing these fuses, make sure all screws are tight.
Bulb Replacement
See page 149 for bulb specifications.
Front turn signal lights
Front side marker and turn signal lights/position lights
Rear turn signal/brake and taillights
Brake and taillights/ back-up lights
License plate lights
(cont'd)
Bulb Replacement (cont'd)
Interior light
Vanity mirror light (US: LX/EX, Canada: EX-R)
Door courtesy lights (US: LX/EX, Canada: EX-R)
Trunk light
High-mount brake light
Tires
The factory installed tires on your car were selected to match the car's performance capabilities and to provide the best combination of handling, ride comfort, and tread wear. We recommend that you get the same size, type, and grade of tires when replacement is necessary. If your tires have an all-season tread design, the model name will be followed by the marking: "M + S" (mud and snow) or "all-season". If you decide not to get the same brand of tires as those originally installed, you should make sure that the replacements are the radial type, of the same size, load range, and speed rating as the original tires. If you have any questions about your car's tires, please contact your Honda dealer.
Inflation Pressures The tire label on the driver's door jamb shows recommended tire pres- sures for carrying loads up to the limit shown. These pressures were chosen to provide you with the best combi- nation of tread life, riding comfort and stability under normal driving conditions. Improper inflation can reduce both tire life and load carrying capacity. Check the tire pressures at least once a month, including the spare. Lower pressure than recommended lets the tread and sidewalls flex too much, causing increased tire temperatures, uneven wear, and poor handling. Pressure higher than recommended can make the tire too stiff, increasing the chance of damage from road hazards, and also causing uneven wear.
TIRE LABEL
CAUTION:
Check tire pressure when the tires are cold. (After the car has been parked for more than 3 hours or driven less than 1 mile/1.6 km.) Tire pressure may increase as much as 41 kPa (6 psi) when the tire is hot, so NEVER ADJUST tire pressure when the tires are hot. Never inflate load range B tires to more than 220 kPa (32 psi) cold. Cars with luggage racks or cartop carriers DO NOT have greater load limits than those on the label.
(cont'd)
Tires (cont'd)
Winter Driving Tires marked "M + S" or "all season" have an all-weather tread design and should be suitable for most driving conditions. However, snow tires and tire chains may be required under some conditions. If your tires do not have these markings, they may not be suitable for winter driving conditions. We recommend snow tires or tire chains for snow and icy conditions.
Snow Tires If you use snow tires, they should be of the same size, construction and load capacity as the original tires on your car. Snow tires must be installed in sets of four, or they may cause poor handling. Driving with snow tires on dry roads can reduce your car's performance during acceleration, turning, and stopping. If you need further information on snow tires, please contact your Honda dealer.
Tire Chains Use chains only when conditions require them. Check with local authorities or Provinces for requirements prior to installing tire chains. Make sure the chains are the right size for your tires. Install them only on the drive wheels of your car, and do so as tightly as possible, following the manufacturer's instructions. If metal chains are used, they must be SAE Class " S ." Cable type traction devices can also be used. Drive slowly with chains installed. If you hear the chains contacting your car's body or chassis, stop and tighten them.
CAUTION:
If the contact continues, slow down until it stops or your car can be damaged. Chains that are the wrong size or improperly installed can damage your car's brake lines, suspension, body, and wheels.
If you need further information on tire chains, please see your Honda dealer. Remove the chains as soon as the road is clear of ice and snow.
Tire Replacement Honda recommends that you replace tires in sets of four, or in pairs, front or rear. If you need to replace only one tire, mount the new tire opposite the tire showing the least amount of wear. For instance, if the left front tire shows the least amount of wear, mount the new tire on the front right side.
indicators to
The original tires on your car have tread wear indicate when they should be replaced. The indicators appear as bands about 12.7 mm (1/2 in) wide when the tire tread depth is less than 1.6 mm (1/16 in). When indicators appear across two or more grooves in a row, you should replace the tire.
INDICATOR LOCATION MARKS
TREAD WEAR INDICATORS
Driving on worn-out tires is very hazardous, and will reduce braking effectiveness, steering accuracy and traction.
When replacing tires, use only the recommended tire size. Wheel rim widths and offsets must be those recommended by American Honda Motor Co., Inc. Contact the Zone Office nearest you as shown on the inside of the back cover.
Tires and wheels other than those recommended may be unsafe. Do not mix radial and bias ply tires on the same car.
(cont'd)
Tires (cont'd)
Tire Balancing
Unbalanced tires may affect handling and tire wear. A tire should always be rebalanced after it has been dismounted from the wheel.
Your original tires were properly balanced before the car left the factory, but may need rebalancing at some time during the life of the tire. Tire balancing for the COMPACT spare is not necessary.
CAUTION: Use only Genuine Honda aluminum wheel weights if your car is equipped with aluminum wheels. Non genuine Honda wheel weights may corrode and damage the aluminum wheel.
Tire Rotation Tires may wear unevenly when used for a long time in the same position on the car. To avoid this, rotate the tires every 7,500 miles (12,000 km). If abnormal or uneven wear develops between rotations, the cause should be found and corrected as soon as possible. The illustration shows how the tires can be rotated. The COMPACT spare tire must not be included in tire rotation.
NOTE: Brake pads should be inspected for wear whenever the tires are rotated.
Front
Tire Traction
Worn tires or slippery road surfaces can reduce driving, cornering and braking traction. To reduce the possibility of losing traction, slow down when the road gets slippery, replace tires when wear indicators are visible, and KEEP TIRES PROPERLY INFLATED.
Air Conditioner Care
Condenser and Radiator Check the engine radiator and the air conditioner condenser (in front of the radiator) for accumulated dirt, insects or leaves. Carefully brush or hose them off to assure maximum cooling performance.
CAUTION: Radiator and condenser fins are very thin and easily damaged; do not bend them with the high water pressure or brush.
Compressor Drive Belt Check the compressor belt tension monthly, during periods when you use the air conditioner a lot.
If the engine has been running, some engine components may be hot enough to burn you.
When pushed with 98 N (22 Ib) of force midway between the alternator pulley and the engine crankshaft pulley, the belt should deflect about: 10 —12 mm (0.4 — 0.5 in)
ALTERNATOR DRIVE PULLEY
CRANKSHAFT PULLEY
COMPRESSOR DRIVE PULLEY
(cont'd)
Air Conditioner Care (cont'd)
System Maintenance Run your air conditioner at least once a week for about ten minutes, even during the off season, to lubricate the seals and the inside of the compressor and, to verify that the system is functional.
If the air conditioner is not cooling properly, it may indicate an undercharged system. Have your dealer check the system for leaks, then evacuate and charge the system with refrigerant 12. Charging quantity: 800 — 850 g (28.3 — 30.1 oz)
CAUTION: Prolonged use of an undercharged system may damage the compressor.
Appearance Care
Interior Trim Remove dust and loose dirt with a vacuum cleaner. Wipe the vinyl with a clean, damp cloth or sponge. Stains can be removed with a commercially available vinyl cleaner.
Do not use thinner, gasoline, kerosene, naphtha, or other solvents on the interior. They are toxic, flammable, and hazardous and could damage the material you're cleaning.
Windows A 10 to 1 mix of water and white vinegar, or a commercially available glass cleaner may be used to clean windows and to remove the dust film sometimes caused by the ingredients used in interior vinyls and plastics.
NOTE: Do not put this solution in the windshield washer reservoir, it will damage the windshield washer pump.
Be careful not to scratch or damage the defogger wires when clean- ing the inside of the rear window; wipe the window horizontally along the wires, not up and down. Dry the windows with a lint-free cloth or paper towel. Keep all the windows clean for maximum visibility.
(cont'd)
Appearance Care (cont'd)
Exterior Care
Washing Rinse all loose dirt off the car by spraying it with lukewarm or cold water. Do not use hot water. Wash using a soft-bristle brush, sponge, or cloth with water containing a mild detergent such as a liquid dishwashing detergent. Remove oil, tar, tree sap, etc., with tar remover or turpentine. Remove road salt, insects, etc., with mild detergent and lukewarm water. Any of these substances may damage the finish if left on painted surfaces. Rinse the car well. Promptly wipe with a chamois or soft towel to prevent water-spotting. Do not let water or soap air-dry on painted surfaces. During wiping, inspect the surface for stone chips and scratches; paint them with touch-up paint so they won't rust (touch-up paint is available through your Honda dealer). For further instructions on corrosion protection, refer to the Rust Prevention section on the next pages.
Waxing Wax the car when water will no longer "bead" on the paint. Always wash and dry the car before you wax it. Use a good quality liquid or paste wax, and follow the manufacturer's instructions. Wax all the metal trim to keep its luster.
NOTE: Removing oil, tar, etc., with a spot remover will usually strip the wax from the surrounding finish. Be sure to re-wax these areas even if the rest of the car does not yet need waxing.
Aluminum Alloy Wheels (US: EX, Canada: EX-R) CAUTION:
Wash the wheels after driving on snowy or icy roads where salt has been applied. Avoid off-road driving. Brush, rocks, dirt, and severe impact may damage the wheels. Install tire chains carefully. Improperly installed chains can cause damage to the wheels. Honda aluminum wheels are treated with a protective finish. Wash them with a low-phosphate detergent and sponge. Do not use abrasive cleaners or stiff brushes. Always install aluminum wheels in sets of four. If mixed with other types, the car's handling may be affected.
Rust Prevention Rusting is likely to occur in parts of the car where water is trapped or where there is continual dampness.
Water will collect inside doors and body panels if drain holes become clogged. Water which seeps under or soaks floor mats will subject floor sections to prolonged wetness or dampness. Road dirt or sand, which collects and fills recesses on the underside of the car, retains moisture long after the rest of the car has dried.
The removal of paint and undercoating by stones, gravel, and minor accidents immediately exposes metal to air and moisture. Rusting is increased by high humidity and by the presence of corrosive substances in the air or on the roads.
Salt used for road de-icing will coat the bottom of the car and hasten rusting. Localities with high humidity have greater potential for rust problems, especially where salt is also present on the road or in moist sea air. Industrial pollution will accelerate finishes and promote rusting.
the deterioration of paint
(cont'd)
Appearance Care (cont'd)
Preventive Service Check all drain holes in the doors and body panels for clogging and clear if necessary. When washing your car, also clean the underside of the car by using high pressure water; inside front fender, and After washing your car or after heavy rain, check for leaks. Dry any wet areas of your car's interior. Have leaks repaired as soon as possible. After driving your car, wipe off any road dirt or salt on the radio antenna, with it fully extended.
inside rear wheel housing,
under rear bumper.
above subframe,
rear suspension,
CAUTION: Cars with ABS have speed detection devices mounted at each wheel (total four detectors per vehicle). Care should be taken when clearing mud, snow, etc., from the wheels not to damage the detectors.
SPEED DETECTOR
Body Repair
Replacement Body and Fender Parts If your vehicle incurs body damage and requires replacement parts, we encourage you to use only Genuine Honda sheet metal body and fender parts. Many insurance companies are specifying imitation sheet metal parts for collision repairs in an effort to reduce claim costs; however, if imitation parts are used the following conditions may apply:
There is no assurance that imitation parts will equal the fit and finish of Genuine Honda sheet metal parts; and in our experience they often do not. There is no assurance that imitation parts will resist corrosion as well as Genuine Honda sheet metal parts. Imitation sheet metal parts are not covered by the Honda Limited Warranty.
To ensure your continued satisfaction with your Honda vehicle in the event of an accident, contact your insurance adjuster and insist on Genuine Honda parts in the repair of your vehicle.
Spare Tire
COMPACT Spare Tire Your car is supplied with a COMPACT spare tire and wheel for temporary use only in the event of a flat tire. Use the COMPACT spare only when you have to, and only to go as far as the next garage or dealer to have the regular tire repaired and reinstalled.
Because you will rarely use the COMPACT spare, be sure to regularly check its condition and air pressure (41 5 kPa, 60 psi), so it will be ready when you need it. This type of tire holds less air at higher pressure than a regular tire, so it will inflate (or deflate if there is a leak) more rapidly; check its pressure often and add air gradually if it needs any.
The COMPACT spare tire has a different tire size, air pressure re- quirement, tread life and maxi- mum speed rating than the four regular tires on your car. Disre- garding these warnings may re- sult in tire failure, loss of vehicle control and possible injury to vehicle occupants. Do not exceed 50 mph (80 km/h) under any circumstances when using the COMPACT spare. Do not mount snow chains on the COMPACT spare. They will not fit properly and will damage the tire and possibly your car. If you must use the COMPACT spare when driving on roads covered with snow or ice, use it as one of the rear tires and mount chains only on the front two regular tires.
TREAD WEAR INDICATOR
INDICATOR LOCATION MARK
The COMPACT spare tire has a much shorter tread life than regu- lar tires. Replace the tire as soon as tread wear indicators appear as solid bands across the tread. Replace with a tire of exactly the same size and construction. The COMPACT spare tire and wheel set was designed espe- cially for your car; do not use it on any other vehicle; do not in- stall any other tire on this wheel which is not identical to the original in size and construction, and do not use the COMPACT spare tire on any other wheel. Because the COMPACT spare is smaller in size and higher in air pressure than a regular tire, it will ride more harshly with less ground clearance and may have less traction on some road surfaces. Drive cautiously.
Changing a Flat Tire
Do not attempt to change a tire unless the car is on firm, level ground and well out of the flow of traffic. Park the car on a firm, level surface, apply the parking brake, turn on the hazard warning switch, turn the ignition off and put the transmission in gear (Park for automatic transmission). 1. Remove the cover. 2. Remove the jack. NOTE: Turn the connector on the end of the jack counterclockwise to loosen it from its mount.
COVER
JACK
TOOL BAG
COMPACT SPARE
3. Remove the lug wrench/jack handle and jack handle extension
from the tool bag.
4. Remove the spare tire. 5. Place blocks in front and back of the wheel diagonally opposite
the tire you are changing.
6. Use the lug wrench to loosen the wheel lug nuts counterclock-
wise one-half turn. (US: EX, Canada: EX-R) First remove the center cap from the wheel by prying it out with a common flat screwdriver (not provided in the tool bag).
CAUTION: Hold the center cap with your hand then pry it off using a rag to protect the cap and the wheel.
CENTER CAP
SCREWDRIVER
Follow tire changing preparations and procedures carefully to reduce the possibility of injury. The jack is designed for changing tires only. STAND CLEAR, DO NOT get under the car and DO NOT run the engine when the car is supported only by the jack.
7. Place the jack under the car as shown and raise the car by turning
the handle clockwise until the tire is slightly off the ground.
To reduce the possibility of injury, be sure to use the jack provided with the car and the correct jacking points; never use any other part of the car for jack support.
JACK HANDLE EXTENSION
8. Remove the lug nuts and wheel.
(US: DX/LX, Canada: EX) Remove the lug nuts, wheel cover, and wheel.
LUG WRENCH/JACK HANDLE
WHEEL COVER
LUG NUT
(cont'd)
VALVE
Changing a Flat Tire (cont'd)
9. Everytime you install the wheel on the brake hub, use a clean rag to wipe any dirt off the mounting surface of the hub and the wheel. This will assure a tight, even contact between the wheel and hub.
10. Install the spare, and lug nuts hand tight. 11. Lower the car, remove the jack, then tighten the lug nuts
securely in an " X" pattern as shown.
12. Tighten the lug nuts to the recommended torque:
110 N.m(11 kg-m,80 Ib-ft) If a torque wrench was not used, ask an authorized Honda dealer to verify the torque as soon as possible.
TIGHTENING TORQUE 110 N.m (11 kg-m,80 Ib-ft)
13.Repair or replace the damaged tire as soon as you can, reinstall it
in its original position, then put the spare back in the car.
CAUTION: Always stow the jack, tools, and tire securely to prevent them from becoming dangerous projectiles in an accident.
14.Secure the tire and the spacer as shown in the illustration.
SPACER
COMPACT SPARE TIRE
NORMAL TIRE
Jump Starting
To start a car with a dead battery, use another battery of the same voltage, and the proper jumper cables.
Procedures other than those below could cause injury or damage from battery acid spray, explosion or charging system overload. Never connect the jumper cable directly to the negative post of the "dead" battery. Never allow the two cars to touch each other. Never allow the jumper cable clamps to touch each other. Never lean over the battery when making connections. Never attempt to jump start a vehicle with a frozen battery. The battery could rupture and explode. If you suspect a frozen battery, remove the vent caps and check the fluid. If there seems to be no fluid, or if you see ice, do not attempt a jump start until the fluid thaws.
CAUTION: If jumper cables are connected backwards, the car's main fuse may blow.
1 .Turn off all lights, heater and other electrical loads, set the parking
brake, and shift the transmission to Neutral or Park.
2. Use one cable to connect the positive terminal of the booster
battery to the positive terminal of the "dead" battery.
DEAD BATTERY
Positive to positive
Do not attach cable here.
Negative to the engine, not to the battery
BOOSTER BATTERY
3. Use the other cable to connect the negative terminal of the
booster battery to the engine at the ground cable as shown.
4.To remove the cables, reverse the above procedures exactly.
DO NOT push or tow a car to start it. The forward surge when the engine starts could cause a collision. Also, under some conditions, the catalytic converter could be damaged. A car equipped with an automatic transmission cannot be started by pushing or towing.
NOTE: (US: EX, Canada: EX-R) After jump-starting the car, there is a possibility that the ABS warning light may come on due to insufficient battery voltage. After the battery is sufficiently recharged and the engine is turned off and restarted, the ABS warning light should indicate that the ABS is OK, by coming on for a few seconds each time the engine is started. If the light remains on after recharging, have it checked by a Honda dealer.
Towing
If towing is necessary, contact a professional towing service. Your authorized Honda dealer can assist you with detailed towing instructions.
Never use tow chains or rope to tow a car; your ability to safely control the car may be adversely affected.
We recommend the following: Flat Bed Equipment — Entire car is winched on a flat bed vehicle. This is the best way of transporting your Honda. Wheel Lift Type — Tow with the front wheels off the ground.
If the car can only be towed with the front wheels on the ground, make sure the transmission is full of fluid (see pages 110 — 111), and tow with the transmission in neutral (N) and the ignition key in the I position.
CAUTION: To avoid serious damage on automatic transmission cars, first start the engine and shift to D4, then to N and shut the engine off. If the engine does not run, or the transmission cannot be shifted while the engine is running, the car must be transported on flat bed equipment.
Check local regulations for towing.
CAUTION:
Do not exceed 35 mph (55 km/h) or tow for distances of more than 50 miles (80 km). If a sling type tow is used, the tow truck driver should position wood spacer blocks between your car's frame and the chains and lift straps to avoid damaging the bumper and the body. Do not use the bumpers to lift the car or to support the car's weight while towing.
If Your Car Gets Stuck
If your car gets stuck in sand, mud, or snow, call a professional towing service for assistance in getting your car out.
CAUTION:
Do not rev up the engine and allow the wheels to spin freely at high speed. Severe transmission damage may result if the wheels are allowed to spin for more than a few seconds. DO NOT try to free a car with automatic transmission from snow, etc. by rocking the car alternately between forward and reverse gears. Severe transmission damage may result from shifting into gear with the wheels moving.
Specifications
*1 Including the coolant in the reserve tank 0.6
(0.16 US gal, 0.13 Imp gal) and that
remaining in the engine.
*2 Excluding the oil remaining in the engine. *3 US Cars *4 Canada Cars
page 120.
Identification Numbers
The Vehicle Identification Number (V.I.N.) is stamped on a plate attached to the top left side of the dashboard. It also appears on the Certification label (Canada cars: Canada Motor Vehicle Safety Standard Compliance Label) attached to the driver's door jamb, as well as under the hood on the body, directly behind the engine.
NOTE: The V.I.N. is also provided in bar code on the Certification label.
VEHICLE IDENTIFICATION NUMBER
VEHICLE IDENTIFICATION NUMBER
CERTIFICATION LABEL
ENGINE NUMBER
TRANSMISSION NUMBER
The Engine Number is stamped on the right front side of the engine block. The Transmission Number appears on a label on top of the transmission.
DOT Tire Quality Grades
US Cars The tires on your car meet Federal Safety Requirements. All tires are also "graded" according to Department of Transportation (DOT) standards for tread wear, traction and temperature.
Three grades are shown on the tire sidewall.
TIRE
WHEEL RIM
Tread Wear The tread wear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one half (1-1/2) times as well on the government course as a tire graded 100. The the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.
relative performance of
tires depends upon
Traction The traction grades, from highest to lowest, are A, B, and C, and they represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
The traction grades assigned are based on braking (straight ahead) traction tests and do not include cornering (turning) traction.
(cont'd)
DOT Tire Quality Grades (cont'd)
Temperature The temperature grades are A (the highest), B and C representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.
The tire temperature grade is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
Emission Controls
Sources of Emissions The combustion process produces carbon monoxide, oxides of nitrogen, and hydrocarbons. The evaporation of fuel in the fuel tank also produces hydrocarbons. Control of oxides of nitrogen and hydrocarbons is very important since, under certain conditions, when subjected to sunlight, they react to form photochemical smog. Carbon monoxide does not react to form smog, but it is toxic.
The Clean Air Act The Clean Air Act* requires all vehicle manufacturers to explain in writing the operation and maintenance of their emission control systems. Maintenance instructions are included on pages 100 — 102; the operation of each system is explained below and on the following page.
Replacement Parts The emission control systems on your new Honda were designed, built and certified regulations implementing the Clean Air Act. Honda recommends only the use of new, Genuine Honda parts or their equivalent. The use of other replacement parts which are not of equivalent quality may impair the effectiveness of your car's emission control systems.
to conform with
the Federal
Crankcase Emission Control System To prevent crankcase emissions, your car is equipped with a Positive Crankcase Ventilation (PCV) System which routes blowby gases from the crankcase, through the PCV valve and intake manifold, into the combustion chamber.
Evaporative Emission Control System The Evaporative Emission Control System is designed to prevent fuel vapors from escaping into the atmosphere. Fuel vapors from the fuel tank are directed into the charcoal canister where they are adsorbed and stored while the engine is stopped or idling. When the coolant temperature rises to a certain value, the vapors are drawn into the engine through the throttle body and the intake manifold during normal engine operation.
* In Canada, Honda vehicles comply with the Canadian Motor Vehicle Safety Standards (CMVSS) on Emissions valid at the time they are manufactured.
(cont'd)
Emission Controls (cont'd)
Engine Exhaust Controls The engine exhaust emission control systems are designed to control combustion during idle, acceleration, cruise, and deceleration. These systems are entirely separate from the crankcase and evaporative emission control systems described previously.
PGM-FI System The PGM-FI system consists of three independent sub-systems; Air Intake, Electronic Control, and Fuel Control, thus allowing more accurate control of air/fuel ratios under all operating conditions. The Electronic Control Unit (ECU) detects the amount of air drawn into the cylinders and determines the amount of fuel to be injected to provide the optimum air/fuel ratio for all engine needs. Ignition Timing Control System This system automatically controls the ignition timing to reduce the amount of HC and NOx.
Catalytic Converter The catalyst is used to convert hydrocarbons (HC), carbon monoxide (CO) and oxides of nitrogen (NOx) in the exhaust gas, to carbon dioxide (CO
) and water vapor.
), dinitrogen (N
Exhaust Gas Recirculation (EGR) The EGR system is designed to control the formation of oxides of nitrogen fuel mixture burns at high temperature. It works by recirculating exhaust gas through the EGR valve and intake manifold into the combustion chambers where it reduces peak temperature by diluting the air/fuel mixture.
(NOx) caused when
Catalytic Converter
A catalytic converter is installed in the exhaust system to help clean-up the harmful exhaust gases that can cause air pollution. To be effective, the converter must work at high temperature, so don't park your car over dry grass, leaves or anything else that could burn easily. To stay effective, the converter must not be contaminated by leaded gasoline; use only unleaded gas as explained on page 82.
CATALYTIC CONVERTER
CAUTION: The converter can be overheated and damaged if it's fed too much unburned fuel mixture from the engine, so: — Don't push or tow the car to start it; if the battery is dead, jump
start the car as shown on page 144.
— Don't turn the key off while the engine is running above idle
speed.
parts.
— Don't change the ignition timing, or remove any emission control
— Use only the spark plugs specified in this manual. — Don't keep driving your car if it isn't running properly, or if its CHARGE warning light comes on; have it checked by your Honda dealer.
Warranty Service
Warranty (US Cars) The following warranties are provided with every new vehicle:
1. New Car Limited Warranty 2. Emission Control Systems Defects Warranty 3. Emissions Performance Warranty 4. Original Equipment Battery Limited Warranty 5. Rust Perforation Limited Warranty 6. Accessory Limited Warranty 7. Replacement Parts Limited Warranty 8. Replacement Muffler Lifetime Limited Warranty 9. Seat Belt Limited Warranty
10. Replacement Battery Limited Warranty
Your car's original tires are covered by their manufacturer. Tire warranty information is in a separate tire warranty booklet.
All warranty details pertaining to your car can be found in the Warranty booklet provided with your new car except the required maintenance schedule which is contained here in the Owner's Manual.
If you are unable to obtain warranty service or are dissatisfied with the warranty decision or service you received at an authorized Honda dealership, you should that dealership's Service Manager. This will normally resolve your problem. If it does not resolve your problem you should appeal the decision with the owner of the dealership. Please bear in mind that your problem will likely be resolved at the dealership, using the dealer's facilities, equipment, and personnel. So it is very important that your initial contact be with the dealer or his management.
the matter with
review
After following these steps, the matter reviewed by American Honda you should contact the Zone Office serving your area, as shown on the map on the inside of the back cover. When contacting American Honda, please provide the Zone Office with the following information:
if you wish
to have
Vehicle Identification Number Servicing Dealer Name and Address Date of Purchase Mileage on your Car Your Name, Address, and Phone Number Nature of Problem Selling Dealer
After a review of the facts, you will be advised of what can be done.
(Canada Cars) Please refer to the 1992 Warranty and Maintenance Guide that came with your car.
Reporting Safety Defects
(US Cars) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co., Inc.. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or American Honda Motor Co., Inc. To contact NHTSA, you may either call the Auto Safety Hotline toll- free at 1-800-424-9393 (or 366-0123 in Washington, D.C. area) or write to: NHTSA, U.S. Department of Transportation Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline.
Airbag
.......See "Supplemental
Restraint System"
Air Conditioner
Care........................................ 131
Operation.................................. 64
Air Filter........................................ 119
Air Pressure, Tires....................... 127
Aluminum Alloy Wheels.............. 135
Antenna.......................................... 71
Antifreeze .. See "Radiator coolant"
Anti-lock Brake System (ABS)..... 34
Anti-lock Brake Fluid............. 116
ABS Warning Light.................. 41
Anti-theft Steering Column Lock
System...................................... 86
Appearance Care........................ 133
Ashtrays......................................... 58
Audio System ................................ 71
Automatic Transmission
Driving Technique.................... 94
Fluid......................................... 111
Operation................................. 93
Shift Lever Position Indicator. 38
Battery
Charging System Warning Light... 39
Jump Starting........................ 144
Maintenance........................... 122
Specification.......................... 149
Beeper System
Fasten Seat Belt Beeper...........12
Key Reminder........................... 86
Light Reminder Chime............. 49
Belt, Seat
..............See "Seat Belt System"
Beverage Holder............................. 57
Body Repair.................................. 137
Brake Warning Light...................... 41
Brakes
ABS Warning Light.................. 41
Anti-lock Brake System
(ABS)..................................... 34
Anti-lock Brake Fluid............. 115
Brake Failure Warning Light.... 41
Brake Fluid.............................. 116
Brake System Design............ 115
Index
Brake Wear............................ 115
Brake Wear Indicators........... 115
Parking Brake........................... 54
Parking Brake Warning Light.. 41
Break-in Period................................. 2
Bulb
Replacement.......................... 125
Specification.......................... 149
Buzzer........... See "Beeper System"
Capacities..................................... 148
Care and Cleaning........................ 133
Catalytic Converter..................... 155
Certification Label....................... 150
Chains.Tires ................................. 128
Check Engine Warning Light........ 40
Child Safety ........................... 2 7 - 33
Child Seat Locking Clip............ 32
Child Seat Storage................... 33
Guidelines......................... 2 8 - 30
Infant Seats.............................. 29
Safety Reminders.................... 28
Seating Location...................... 27
Tethers..................................... 31
Toddler Seats........................... 30
Cigarette Lighter............................ 58
Clock............................................... 56
Clutch Fluid .................................. 117
COMPACT Spare Tire................. 138
Coolant Temperature Gauge ........ 37
Coolinglwith A/C).......................... 64
Cooling System............................ 112
Crankcase Emission Control System ...... 153
Cruise Control
Indicator.................................... 38
Operation.................................. 52
Daytime Running Light (DRL)........ 51
DRL Indicator Light.................. 42
Defogger......................................... 47
Defroster........................................ 67
Dimmer Switch, Headlights.......... 49
Doors
Locks.................................... 3, 25
Power Door Locks..................... 4
Warning Light........................... 43
(cont'd)
Index (cont'd)
Emergency
Changing Flat Tire.................. 140
Hazard Warning System ......... 50
If Your Gets Stuck................. 147
Jump Starting........................ 144
Towing.................................... 146
Warning and Indicator Lights.. 38
Emission Controls........................ 153
Engine
Coolant ................................... 112
Coolant Temperature Gauge .. 37
Exhaust Controls................... 154
Identification Number............ 150
Oil and Filter........................... 107
Oil Pressure Warning Light..... 40
Specification.......................... 149
Engine Exhaust Gas Warning........ 89
Evaporative Emission Control
System ................................... 153
Exhaust Gas Recirculation.......... 154
Exterior Care ............................... 134
Filters
Air........................................... 119
Engine Oil................................ 108
Fuel.......................................... 119
Fluid.................................... See "Oil"
Foreign Countries,Operation in .... 83
Front Seat
Adjustment................................. 6
Fuel
Filler Door and Cap................... 84
Filter........................................ 119
Gasohol..................................... 82
Gasoline..................................... 82
Gauge........................................ 36
Requirement............................. 82
Reserve Warning Light............ 41
Fuse
Checking and Replacing ........ 123
Specification.......................... 149
Gasoline........................... See "Fuel"
Gas Station Information. Back cover
Gauges............................................ 36
Glove Box....................................... 57
Hazard Warning System ............... 50
Headlights
Flasher...................................... 49
High Beam Indicator................. 38
High Beam/Low Beam Switch
.............................................. 49
Reminder Chime ..................... 49
Switch ...................................... 49
Headlight High Beam Indicator Light
.................................................. 38
Head Restraints................................ 7
Heating............................................ 65
High Beam
Indicator Light.......................... 38
Switch ...................................... 49
Hood Latch..................................... 54
Identification Numbers................ 150
Ignition
Keys............................................ 3
Switch....................................... 86
Ignition Switch Light...................... 50
Important Safety Reminders
................................... . 11, 20, 28
Indicator Lights .............................. 38
Inflation Pressures, Tire .............. 127
Instrument Panel............................ 35
Instrument Panel Brightness Control
.................................................. 50
Interior Light................................... 51
Interior Trim Care........................ 133
Jack.............................................. 140
Jump Starting.............................. 144
Keys
Door Locks................................. 3
Glove Box................................. 56
Ignition....................................... 86
Key Reminder Beeper.............. 86
Keys............................................ 3
Trunk Lock ................................. 5
Lap Belt........................................... 13
Lap/Shoulder Belt.......................... 12
Lights
Bulb Replacement.................. 125
Daytime Running Lights .......... 51
Fuse Replacement................. 123
Light Reminder Chime............. 49
Operation.................................. 49
Warning and Indicator Light.... 38
Locks
Anti-theft Steering ColumnLock
.............................................. 86
Doors........................................... 3
Fuel Filler Door......................... 84
Glove Box ................................. 56
Power Door Lock....................... 4
Trunk........................................... 5
Lumbar Support............................... 8
Maintenance
Indicator................................... 44
Records.................................. 103
Schedule................................. 100
Manual Transmission
Maximum Allowable Speeds .. 91
Oil............................................ 110
Recommended Shift Speeds.. 91
Shifting..................................... 90
Meters, Gauges......... See "Gauges"
Mirrors
Manual Mirrors......................... 48
Power Mirrors.......................... 48
Rearview Mirrors..................... 48
Moonroof
If the Moonroof Won't Close.. 70
Maintenance............................. 70
Operation.................................. 69
Numbers, Identification............... 150
Octane Rating,
Gasoline..................... See "Fuel"
Odometer....................................... 36
Oil
Clutch Fluid............................. 117
Engine Oil................................ 107
Fluid Locations....................... 106
Oil Pressure Warning Light..... 40
Power Steering Fluid ............. 118
Transmission Oil/Fluid........... 110
Operation In Foreign Countries .... 83
Panel Brightness Control............... 50
Parking Brake................................. 54
PGM-FI
Check Engine Warning Light... 40
System ................................... 154
Power
Door Locks................................. 4
Mirrors ...................................... 48
Steering .................................. 118
Windows................................... 55
Pressures, Tire Inflation.............. 127
Preventive Service...................... 136
Radiator Coolant.......................... 112
Radio............................................... 71
Rearview Mirrors........................... 48
Rear Quarter Windows................. 56
Rear Window Defogger................. 47
Reminder Lights
................... See "Warning lights"
Replacement
Air Filter.................................. 119
Bulbs........................................ 125
Engine Oil................................ 108
Fuel Fitter................................119
Fuses....................................... 123
Oil Filter................................... 108
Radiator Coolant.................... 113
Spark Plugs............................. 120
Tires........................................ 129
Wiper Blades.......................... 121
Rust Prevention........................... 135
(cont'd)
Index (cont'd)
Safety Defects, Reporting.......... 158
Safety Indicator Lights.................. 43
Safety Items................................... 88
Seat-back Position......................... 24
Seat Belt System........................... 11
Components............................. 12
Lap/Shoulder Belt.............. 12, 14
Lap Belt..............................13, 16
Maintenance............................. 18
Operation.................................. 11
Pregnant Women..................... 18
Safety Reminders .....
24 - 26
Warning Lights and Beeper..... 12
11,
Seats
Driver's Center Armrest........... 8
Driver's Lumbar Support.......... 8
Front Seat................................... 6
Head Restraints.......................... 7
To Get In/Out of Rear Seat....... 8
Trunk Access from Rear Seat.. 9
Shift Lever Position Indicator....... 38
Shifting
Automatic................................. 92
5-Speed..................................... 90
Spare Tire
Changing a Flat Tire............... 140
COMPACT Spare Tire........... 138
Specifications........................ 148
Spark Plugs .................................. 120
Specifications.............................. 148
Speedometer................................. 36
SRS Indicator Light........................ 42
Starting the Engine ........................ 87
Steering
Anti-theft Column Lock .......... 86
Power Steering...................... 118
Tilt Steering.............................. 45
Stereo Sound System
Operation.................................. 71
Stuck Car..................................... 147
Sunshade........................................ 69
Supplemental Restraint
System (SRS)...................19-23
Components............................. 20
Indicator Light........................... 22
Operation.................................. 21
Safety Reminders.............. 20, 24
System Service........................ 23
Precautions........................... 23
Tachometer.................................... 36
Temperature Gauge, Coolant....... 37
Tilt Steering.................................... 45
Tire
Air Pressure............................ 127
Balancing ................................ 130
Chains ..................................... 128
Changing a Flat Tire............... 140
COMPACT Spare .................. 138
DOT Tire Quality Grades....... 151
Inflation Pressures................. 127
Requirement........................... 151
Rotation.................................. 130
Snow Tires............................. 128
Spare Tire............................... 138
Specification.......................... 148
Tools............................................. 140
Towing ......................................... 146
Towing a Trailer............................. 95
Transmission
Capacity ................................. 148
Identification Number............ 150
Oil/Fluid................................... 110
Shifting the Automatic............ 92
Shifting the Manual.................. 90
Tread Wear.................................. 151
Trip Meter...................................... 36
Trunk
Access From Rear Seat............ 9
Lid................................................ 5
Lid Warning Light..................... 43
Turn Signals.................................... 49
Vehicle Identification Number ... 150
Ventilation...................................... 59
Warning Lights............................... 38
Warranty Service........................ 156
Washer
Reservoir Capacity.................. 46
Windshield Washer.................. 46
Washing........................................ 134
Waxing ......................................... 134
Wearing Seat Belts Properly ........ 13
Wearing the Lap Belt .................... 16
Wearing a Lap/Shoulder Belt........ 14
Wheels.......................................... 135
Windows
Appearance Care .................. 133
Power Windows ...................... 55
Windshield Defogger..................... 47
Windshield Washer....................... 46
Windshield Wipers ........................ 46
Wiper Blades................................ 121
Wipers............................................ 46
Your Occupant Protection
System...................................... 10
Authorized Manuals
Purchasing Factory Authorized Manuals (U.S. Only)
The following publications covering the operation and servicing of your vehicle can be obtained from Helm Incorporated, either by filling out the form or, for credit card holders, calling the toll free phone number on the form. For manuals prior to the year shown below, contact Helm Incorporated, P.O. Box 07280, Detroit, Michigan 48207, or call (313) 883-1430.
61SM404
61SM404EL
61SM431
31SM2620
HON-R
Service Manual: This manual covers maintenance and recommended procedures for repair to engine and chassis components. It is written for the Journeyman mechanic, but is simple enough for most mechanically- inclined owners to understand.
Electrical Troubleshooting Manual: This manual complements the Service Manual by providing in-depth troubleshooting information for each electrical circuit in your car.
Body Repair Manual: This manual describes the procedures involved in the replacement of damaged body parts.
Valid only for sales within the U.S. Canadian owners should
contact their authorized Honda Dealer.
By completing this form you can order the materials desired. You can pay by check or money order, or charge to your credit card. Mail to Helm Incorporated at the address shown on the back of the order form.
These Publications cannot be returned for credit without receiving advance authorization within 14 days of delivery. On returns, a restocking fee may be applied against the original order.
P. O. BOX 07280 DETROIT, MICHIGAN 48207 (313)883-1430
Gas Station Information
Gasoline
UNLEADED only Pump octane of 86 or higher.
Gas Tank-Capacity
64.5 l (17.04 US gal, 14.19 Imp gal)
Tire Pressure (measured cold) front/rear
US: DX/LX, Canada: LX US: EX, COMPACT spare tire, 415 kpa (60 psi) Other Tire Information Label on driver's door jamb
Canada: EX-R
200 kPa (29 psi) 220 kPa (32 psi)
Hood Release Pull handle under left side of dash.
Engine Oil
Use "Energy Conserving II " SG grade oil. 5W-30 preferred (see page 107 for complete viscosity Capacity (including filter): 3.8 l (4.0 US q t, 3.3 Imp qt)
recommendations).
Manual Transmission Oil
Use SF or SG grade oil. 10W-30 or 10W-40 preferred (see page 111 for complete viscosity recommendations). Capacity (including differential): 1.9 l (2.0 US q t, 1.7 Imp qt)
Automatic Transmission Fluid
Honda Premium Formula Automatic Transmission Fluid or an equivalent DEXRON® type Automatic Transmission Fluid (ATF). Capacity (including differential): 2.4 l (2.5 US q t, 2.1 Imp qt)
II
Power Steering Fluid
Use only Honda power steering fluid: do not use ATF or any other brand of power steering fluid because it will damage the system.
AMERICAN HONDA MOTOR CO., INC.
1919 Torrance Blvd. Torrance, CA 90501-2746
Honda Canada Inc.
715 Milner Ave. Scarborough, Ontario M1B-2K8
Honda Motor Co., Ltd. 1991 All Rights Reserved
31SM2620 OOX31-SM2-6200
175009205
Printed in U.S.A.