2016 Ford Fiesta Owners Manual

You will find a Tire Label containing tire inflation pressure by tire size and other important information located on the B-Pillar or the edge of the driver’s door. Inflating Your Tires Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company.

T type tires have some additional information beyond those of P type tires; these differences are described below: A. T: Indicates a type of tire, designated by the Tire and Rim Association (T&RA), that is intended for temporary service on cars, SUVs, minivans and light trucks. B. 145: Indicates the nominal width of the tire in millimeters from sidewall edge to sidewall edge. In general, the larger the number, the wider the tire.

217

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

ABCDEE142545Wheels and Tires

(affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label which is located on the B-Pillar or the edge of the driver’s door. Failure to follow the tire pressure recommendations can cause uneven treadwear patterns and adversely affect the way your vehicle handles Maximum Inflation Pressure is the tire manufacturer's maximum permissible pressure and the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or Tire Label which is located on the B-Pillar or the edge of the driver’s door. The cold inflation pressure should never be set lower than the recommended pressure on the Safety Compliance Certification Label or Tire Label.

You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate. Ford recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge. Use the recommended cold inflation pressure for optimum tire performance and wear. Under-inflation or over-inflation may cause uneven treadwear patterns

WARNING

Under-inflation is the most common cause of tire failures

and may result in severe tire cracking, tread separation or blowout, with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It also may result in unnecessary tire stress, irregular wear, loss of vehicle control and accidents. A tire can lose up to half of its air pressure and not appear to be flat!

Always inflate your tires to the Ford recommended inflation pressure even if it is less than the maximum inflation pressure information found on the tire. The Ford recommended tire inflation pressure is found on the Safety Compliance Certification Label

218

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Wheels and Tires

3. Add enough air to reach the recommended air pressure. Note: If you overfill the tire, release air by pressing on the metal stem in the center of the valve. Then recheck the pressure with your tire gauge. 4. Replace the valve cap. 5. Repeat this procedure for each tire, including the spare. Note: Some spare tires operate at a higher inflation pressure than the other tires. For T type mini-spare tires (refer to the Dissimilar spare wheel and tire assembly information for a description): Store and maintain at 60 psi (4.15
bar). For full-size and dissimilar spare tires (refer to the Dissimilar spare wheel and tire assembly information for a description): Store and maintain at the higher of the front and rear inflation pressure as shown on the Tire Label. 6. Visually inspect the tires to make sure there are no nails or other objects embedded that could poke a hole in the tire and cause an air leak. 7. Check the sidewalls to make sure there are no gouges, cuts or bulges.

When weather temperature changes occur, tire inflation pressures also change. A 10°F (6°C) temperature drop can cause a corresponding drop of 1
psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or Tire Label. To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. Note: If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never bleed or reduce air pressure. The tires are hot from driving and it is normal for pressures to increase above recommended cold pressures. A hot tire at or below recommended cold inflation pressure could be significantly under-inflated. Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve and measure the pressure.

219

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Wheels and Tires

Inspecting Your Tires and Wheel Valve Stems Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check the tire and valve stems for holes, cracks, or cuts that may permit air leakage and repair or replace the tire and replace the valve stem. Inspect the tire sidewalls for cracking, cuts, bruises and other signs of damage or excessive wear. If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced. For your safety, tires that are damaged or show signs of excessive wear should not be used because they are more likely to blow out or fail. Improper or inadequate vehicle maintenance can cause tires to wear abnormally. Inspect all your tires, including the spare, frequently, and replace them if one or more of the following conditions exist:

Tire Wear

When the tread is worn down to one sixteenth of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydroplaning. Built-in treadwear indicators, or wear bars, which look like narrow strips of smooth rubber across the tread will appear on the tire when the tread is worn down to one sixteenth of an inch (2 mm) When the tire tread wears down to the same height as these wear bars, the tire is worn out and must be replaced. Damage Periodically inspect the tire treads and sidewalls for damage (such as bulges in the tread or sidewalls, cracks in the tread groove and separation in the tread or sidewall). If damage is observed

220

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

E142546Wheels and Tires

or suspected have the tire inspected by a tire professional. Tires can be damaged during off-road use, so inspection after off-road use is also recommended. Age

WARNING

Tires degrade over time depending on many factors such as weather, storage conditions, and conditions of use (load, speed, inflation pressure, etc.) the tires experience throughout their lives. In general, tires should be replaced after six years regardless of tread wear. However, heat caused by hot climates or frequent high loading conditions can accelerate the aging process and may require tires to be replaced more frequently. You should replace your spare tire when you replace the road tires or after six years due to aging even if it has not been used. U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and

describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters DOT and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317 mean the 31st week of 1997. After 2000
the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are identification codes used for traceability. This information is used to contact customers if a tire defect requires a recall. Tire Replacement Requirements Your vehicle is equipped with tires designed to provide a safe ride and handling capability. WARNINGS

Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford. The recommended tire and wheel size

221

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Wheels and Tires

WARNINGS

may be found on either the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver's seating position), or the Tire Label which is located on the B-Pillar or edge of the driver’s door. If this information is not found on these labels then you should contact your authorized dealer as soon as possible. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. Additionally the use of non-recommended tires and wheels could cause steering, suspension, axle, transfer case or power transfer unit failure. If you have questions regarding tire replacement, contact your authorized dealer as soon as possible.

When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If the beads do not seat at the maximum pressure indicated, re-lubricate and try again.

WARNINGS

When inflating the tire for mounting pressures up to 20 psi (1.38 bar) greater than the maximum pressure on the tire sidewall, the following precautions must be taken to protect the person mounting the tire: 1. Make sure that you have the correct tire and wheel size. 2. Lubricate the tire bead and wheel bead seat area again. 3. Stand at a minimum of 12 ft (3.66 m) away from the wheel and tire assembly. 4. Use both eye and ear protection. For a mounting pressure more than 20 psi (1.38 bar) greater than the maximum pressure, a Ford dealer or other tire service professional should do the mounting. Always inflate steel carcass tires with a remote air fill with the person inflating standing at a minimum of 12 ft (3.66 m) away from the wheel and tire assembly

Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle

222

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Wheels and Tires

*Avoid potholes and objects on the road *Do not run over curbs or hit the tire against a curb when parking Highway Hazards No matter how carefully you drive there’s always the possibility that you may eventually have a flat tire on the highway. Drive slowly to the closest safe area out of traffic. This may further damage the flat tire, but your safety is more important. If you feel a sudden vibration or ride disturbance while driving, or you suspect your tire or vehicle has been damaged, immediately reduce your speed. Drive with caution until you can safely pull off the road. Stop and inspect the tires for damage. If a tire is under-inflated or damaged, deflate it, remove wheel and replace it with your spare tire and wheel. If you cannot detect a cause, have the vehicle towed to the nearest repair facility or tire dealer to have the vehicle inspected.

It is recommended that the two front tires or two rear tires generally be replaced as a pair. The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Company may affect the operation of your tire pressure monitoring system. If the TPMS indicator is flashing, your TPMS is malfunctioning. Your replacement tire might be incompatible with your TPMS, or some component of the TPMS may be damaged. Safety Practices

WARNINGS

If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds.

Do not spin the wheels at over 35 mph (56 km/h). The

tires may fail and injure a passenger or bystander.

Driving habits have a great deal to do with your tire mileage and safety. *Observe posted speed limits *Avoid fast starts, stops and turns

223

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Wheels and Tires

Tire and Wheel Alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment. Have an authorized dealer check the wheel alignment periodically. Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by an authorized dealer. Front-wheel drive vehicles and those with an independent rear suspension (if equipped) may require alignment of all four wheels. The tires should also be balanced periodically. An unbalanced tire and wheel assembly may result in irregular tire wear. Tire Rotation Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.

Note: Your vehicle may be equipped with a dissimilar spare wheel and tire assembly. A dissimilar spare wheel and tire assembly is defined as a spare wheel and tire assembly that is different in brand, size or appearance from the road tires and wheels. If you have a dissimilar spare wheel and tire assembly it is intended for temporary use only and should not be used in a tire rotation. Note: After having your tires rotated, inflation pressure must be checked and adjusted to the vehicle requirements. Rotating your tires at the recommended interval (as indicated in the Scheduled Maintenance chapter) will help your tires wear more evenly, providing better tire performance and longer tire life. Front-wheel drive vehicles (front tires on the left side of the diagram)

224

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

E142547Wheels and Tires

Sometimes irregular tire wear can be corrected by rotating the tires. USING SUMMER TIRES Summer tires provide superior performance on wet and dry roads. Summer tires do not have the Mud and Snow (M+S or M/S) tire traction rating on the tire side wall. Since summer tires do not have the same traction performance as All-season or Snow tires, we do not recommend using summer tires when temperatures drop to about 45°F (7°C) or below (depending on tire wear and environmental conditions) or in snow and ice conditions. Like any tire, summer tire performance is affected by tire wear and environmental conditions. If you must drive in those conditions, we recommend using Mud and Snow (M+S, M/S), All-season or Snow tires. Always store your summer tires indoors at temperatures above 19°F (-7°C). The rubber compounds used in these tires lose flexibility and may develop surface cracks in the tread area at temperatures below 19°F (-7°C). If the tires have been subjected to 19°F (-7°C) or less, warm them in a heated space to at least 41°F (5°C) for at least 24 hours before installing them on a vehicle, or moving the vehicle with the tires installed, or checking tire inflation. Do not place tires near heaters or heating devices used to warm the room where the tires are stored. Do not apply heat or blow heated air directly on the tires. Always inspect the tires after storage periods and before use.

USING WINTER TIRES

WARNING

When you use winter tires on your vehicle, you must make sure that you use the correct lug nuts.

If winter tires are used, you must make sure that you use the correct tire pressures. USING SNOW CHAINS

WARNING

Your vehicle is not approved for use with snow chains.

TIRE PRESSURE MONITORING SYSTEM

WARNING

The tire pressure monitoring system is not a substitute for manually checking tire pressure. The tire

pressure should be checked periodically (at least monthly) using a tire gauge, see Inflating your tires in this chapter. Failure to properly maintain your tire pressure could increase the risk of tire failure, loss of control, vehicle rollover and personal injury.

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.)

225

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Wheels and Tires

The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changing Tires With a Tire Pressure Monitoring System

Note: Each road tire is equipped with a tire pressure sensor located inside the wheel and tire assembly cavity. The pressure sensor is attached to the valve stem. The pressure sensor is covered by the tire and is not visible unless the tire is removed. Take care when changing the tire to avoid damaging the sensor You should always have your tires serviced by an authorized dealer. Check the tire pressure periodically (at least monthly) using an accurate tire gauge. See Inflating Your Tires in this chapter.

As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.

226

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

E142549Wheels and Tires

Understanding Your Tire Pressure Monitoring System The tire pressure monitoring system measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The low tire pressure warning light will turn on if the tire pressure is significantly low. Once the light is illuminated, your tires are under-inflated and need to be inflated to the manufacturer’s recommended tire pressure. Even if the light turns on and a short time later turns off, your tire pressure still needs to be checked.

When Your Temporary Spare Tire is Installed When one of your road tires needs to be replaced with the temporary spare, the system will continue to identify an issue to remind you that the damaged road wheel and tire assembly needs to be repaired and put back on your vehicle. To restore the full function of the tire pressure monitoring system, have the damaged road wheel and tire assembly repaired and remounted on your vehicle. When You Believe Your System is Not Operating Properly The main function of the tire pressure monitoring system is to warn you when your tires need air. It can also warn you in the event the system is no longer capable of functioning as intended. See the following chart for information concerning your tire pressure monitoring system:

227

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Wheels and Tires

Low tire pressure

warning light

Possible cause

Customer action required

Make sure tires are at the proper pres- sure. See Inflating your tires in this chapter. After inflating your tires to the manufacturer’s recommended pressure as shown on the Tire Label (located on the edge of driver’s door or the B-Pillar), the vehicle must be driven for at least two minutes over 20 mph (32 km/h) before the light turns off. Repair the damaged road wheel and tire assembly and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When your temporary spare tire is installed in this section. If the tires are properly inflated and the spare tire is not in use but the light remains on, contact your authorized dealer as soon as possible. Repair the damaged road wheel and tire assembly and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When your temporary spare tire is installed in this section. If the tires are properly inflated and the spare tire is not in use but the light remains on, contact your authorized dealer as soon as possible.

It may take up to two minutes of driving over 20 mph (32 km/h) for the light to turn off after you have filled your tires to the recommended inflation pressure

Solid warning light

Tire(s) under-inflated

Spare tire in use

TPMS malfunction

Flashing warning

light

Spare tire in use

TPMS malfunction

When Inflating Your Tires When putting air into your tires (such as at a gas station or in your garage), the tire pressure monitoring system may not respond immediately to the air added to your tires.

228

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Wheels and Tires

How Temperature Affects Your Tire Pressure The tire pressure monitoring system monitors tire pressure in each pneumatic tire. While driving in a normal manner, a typical passenger tire inflation pressure may increase about 2 to 4 psi (14 to 28
kPa) from a cold start situation. If the vehicle is stationary overnight with the outside temperature significantly lower than the daytime temperature, the tire pressure may decrease about 3 psi (21
kPa) for a drop of 30°F (17°C) in ambient temperature. This lower pressure value may be detected by the tire pressure monitoring system as being significantly lower than the recommended inflation pressure and activate the system warning light for low tire pressure. If the low tire pressure warning light is on, visually check each tire to verify that no tire is flat. If one or more tires are flat, repair as necessary. Check the air pressure in the road tires. If any tire is under-inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure. CHANGING A ROAD WHEEL

WARNINGS

The use of tire sealants may damage your tire pressure monitoring system and should only be used in roadside emergencies. If you must use a sealant, the Ford Tire Mobility Kit sealant should be used. The tire pressure monitoring system sensor and valve stem on the wheel must be replaced by an authorized dealer after use of the sealant.

See Tire Pressure Monitoring System (page 225). If the tire pressure monitor sensor becomes damaged, it will no longer function.

Note: The tire pressure monitoring system indicator light will illuminate when the spare tire is in use. To restore the full functionality of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on the vehicle. If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Have a flat serviced by an authorized dealer in order to prevent damage to the tire pressure monitoring system sensors. See Tire Pressure Monitoring System (page 225). Replace the spare tire with a road tire as soon as possible. During repairing or replacing of the flat tire, have an authorized dealer inspect the tire pressure monitoring system sensor for damage. Dissimilar Spare Wheel and Tire Assembly Information WARNING

Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.

If you have a dissimilar spare wheel and tire, then it is intended for temporary use only. This means that if you need to use it, you should replace it as soon as possible with a road wheel and tire assembly that is the same size and type as the road tires and wheels that were originally provided by Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired. A dissimilar spare wheel and tire assembly is defined as a spare wheel and tire assembly that is different in brand, size or appearance from the road tires and wheels and can be one of three types:

229

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Wheels and Tires

The usage of a full-size dissimilar spare wheel and tire assembly can lead to impairment of the following: • Handling, stability and braking

performance.

• Comfort and noise. • Ground clearance and parking at curbs. • Winter weather driving capability. • Wet weather driving capability. • All-wheel driving capability. When driving with the full-size dissimilar spare wheel and tire assembly additional caution should be given to: • • Driving vehicles equipped with a

Towing a trailer.

camper body.

• Driving vehicles with a load on the

cargo rack.

Drive cautiously when using a full-size dissimilar spare wheel and tire assembly and seek service as soon as possible. Tire Change Procedure WARNINGS

When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from

moving or slipping off the jack, even if the transmission selector lever is in park (P). To help prevent your vehicle from moving when you change a tire, be sure to place the transmission

selector lever in park (P), set the parking brake and block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.

Never get underneath a vehicle that is supported only by a jack. If your vehicle slips off the jack, you or

someone else could be seriously injured.

1. T-type mini-spare: This spare tire begins with the letter T for tire size and may have Temporary Use Only molded in the sidewall. 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: THIS WHEEL AND TIRE ASSEMBLY FOR TEMPORARY USE ONLY. When driving with one of the dissimilar spare tires listed above, do not: Exceed 50 mph (80 km/h). • Load the vehicle beyond maximum • vehicle load rating listed on the Safety Compliance Label. Tow a trailer.

• • Use more than one dissimilar spare tire

at a time.

• Use commercial car washing

equipment. Try to repair the dissimilar spare tire.

• Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking

performance.

• Comfort and noise. • Ground clearance and parking at curbs. • Winter weather driving capability. • Wet weather driving capability. • All-wheel driving capability (if

applicable).

3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare wheel and tire assembly, do not: • • Use more than one dissimilar spare wheel and tire assembly at a time.

Exceed 70 mph (113 km/h).

• Use commercial car washing

equipment.

230

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Wheels and Tires

WARNINGS

Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.

Always use the jack provided as original equipment with your vehicle. If using a jack other than the one

provided as original equipment with your vehicle, make sure the jack capacity is adequate for the vehicle weight, including any vehicle cargo or modifications.

Make sure there is no lubrication (grease or oil) on the threads or the surface between the wheel lugs and nuts. This can cause the lug nuts to loosen while driving.

Note: Passengers should not remain in the vehicle when the vehicle is being jacked. 1. Park on a level surface, set the parking brake and activate the hazard flashers.

2. Place the transmission in park (P)

(automatic transmission) or reverse (R) (manual transmission) and turn the engine off.

3. Remove the carpeted wheel cover. 4. Remove the spare tire bolt securing the

spare tire by turning it counterclockwise.

5. Remove the spare tire from the spare

tire compartment.

6. Remove the retaining bolt securing the

jack by turning it counterclockwise.

7. Remove the jack.

231

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

8. To remove the wrench from the jack,

turn the hex nut on the jack counterclockwise. This will lower the jack and loosen the mechanical lock.

9. Block the diagonally opposite wheel. Loosen each wheel lug nut one-half 10. turn counterclockwise but do not remove them until the wheel is raised off the ground.

Note: Jack at the specified locations to avoid damage to the vehicle. 11.

The vehicle jacking points are shown here, and are depicted on the yellow warning label on the jack.

E175694E142551Wheels and Tires

12.

Indentations in the sills show the location of the jacking points.

13. Remove the lug nuts with the lug

wrench.

14. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. Lower the wheel by turning the jack handle counterclockwise.

15.

16. Remove the jack and fully tighten the

lug nuts in the order shown. See Technical Specifications (page 233).

Stowing the Flat Tire The full-size road wheel can be stowed in the spare tire compartment. 1. Lift the carpeted wheel cover at an

angle to access the spare tire compartment.

2. Place the wheel in the spare tire well with the valve stem facing down. Use the mini-spare bolt to secure the wheel.

3. Place the jack and tools back into the

spare tire compartment.

4. Replace the carpeted wheel cover.

232

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

E145908E1425531234E90589Wheels and Tires

TECHNICAL SPECIFICATIONS Wheel Lug Nut Torque Specifications

WARNING

When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Make sure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while your vehicle is in motion, resulting in loss of control.

Bolt size M12 x 1.5

Ib-ft (Nm)* 100 (135)

*Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. Retighten the lug nuts to the specified torque within 100 miles (160 kilometers) after any wheel disturbance (such as tire rotation, changing a flat tire, wheel removal).

Wheel pilot bore

Inspect the wheel pilot bore and mounting surface prior to installation. Remove any visible corrosion or loose particles.

233

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

E145950Capacities and Specifications

ENGINE SPECIFICATIONS 1.0L EcoBoost

Engine

Cubic inches Required fuel Compression

ratio

Spark plug gap

1.6L Duratec-16V Ti-

VCT 98

1.6L EcoBoost

98

61

Minimum 87 octane

Minimum 87 octane

Minimum 87 octane

10:1

11:1

10:1

0.026–0.030 in (0.65–0.75 mm)

0.028–0.031 in (0.7–0.8 mm)

0.028–0.031 in (0.7–0.8 mm)

Drivebelt Routing 1.0L EcoBoost

1.6L Duratec-16V Ti-VCT

1.6L EcoBoost

234

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

E163197E163198E161372Capacities and Specifications

MOTORCRAFT PARTS Component

1.0L EcoBoost

Air filter element1

Oil filter2
Battery

Spark plugs3
Cabin air filter Windshield wiper blade

SP-538A

1.6L Duratec-16V Ti-

VCT FA-1914

1.6L EcoBoost

FL-910S

BXT-96R-500

SP-525

FP-69

SP-532

WW-2430 (driver side)

WW-1613 (passenger side)

WW-1204 (rear)

We recommend Motorcraft replacement parts available at your Ford dealer or at fordparts.com for scheduled maintenance. These parts meet or exceed Ford Motor Company’s specifications and are engineered for your vehicle. Use of other parts may impact vehicle performance, emissions and durability. Your warranty may be void for any damage related to use of other parts. If a Motorcraft oil filter is not available, use an oil filter that meets industry performance specification SAE/USCAR-36. For spark plug replacement, contact an authorized dealer. Replace the spark plugs at the appropriate intervals. See Normal Scheduled Maintenance (page 319).

235

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Capacities and Specifications

VEHICLE IDENTIFICATION NUMBER The vehicle identification number is located on the left-hand side of the instrument panel.

World manufacturer identifier Brake system, Gross Vehicle Weight Rating, Restraint Devices and their locations Make, vehicle line, series, body type Engine type Check digit Model year Assembly plant Production sequence number

Please note that in the graphic, XXXX is representative of your vehicle identification number. The Vehicle Identification Number contains the following information:

236

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

E142476E142477Capacities and Specifications

VEHICLE CERTIFICATION LABEL

TRANSMISSION CODE DESIGNATION

The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label shall be affixed to either the door hinge pillar, the door latch post, or the edge of the door near the door latch, next to the driver's seating position.

Description

Six-speed automatic transmission Six-speed manual transmission Five-speed manual transmission

The transmission code is on the Safety Compliance Certification Label. The following table shows the transmission code along with the transmission description.

Code

237

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

E167469E142806Capacities and Specifications

CAPACITIES AND SPECIFICATIONS - 1.0L ECOBOOST™ Capacities

WARNING

The air conditioning refrigerant system contains refrigerant R-134a under high pressure. Opening the air conditioning refrigerant system can cause personal injury. Have the air conditioning refrigerant system serviced only by qualified personnel.

Item

Engine oil Engine coolant Brake fluid

Capacity

4.3 qt (4.1 L) 6.1 qt (5.8 L)

Between MIN and MAX on brake fluid

reservoir

Manual transmission fluid (ib5) Windshield washer fluid Fuel tank A/C refrigerant A/C refrigerant compressor oil * Approximate dry fill capacity. Actual amount may vary during fluid changes.

2.2 qt (2.1 L)* Fill as required 12.4 gal (47 L)

24.0 oz (0.68 kg) 4.2 fl oz (125 ml)

Specifications Materials

Name Recommended motor oil (U.S.): Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil XO-5W20-QSP Recommended motor oil (Canada): Motorcraft SAE 5W-20 Super Premium Motor Oil CXO-5W20-LSP12
Recommended motor oil (Mexico): Motorcraft SAE 5W-20 Synthetic Motor Oil MXO-5W20-QSP Optional motor oil (U.S. and Mexico):

Specification

WSS-M2C945-A

WSS-M2C945-A

WSS-M2C945-A

WSS-M2C945-A

238

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Capacities and Specifications

Name

Specification

Motorcraft SAE 5W-20 Full Synthetic Motor Oil XO-5W20-QFS Optional motor oil (Canada): Motorcraft SAE 5W-20 Synthetic Motor Oil CXO-5W20-LFS12
Engine coolant (U.S. and Mexico): Motorcraft Orange Antifreeze/Coolant Prediluted VC-3DIL-B Engine coolant (Canada): Motorcraft Orange Antifreeze/Coolant Prediluted CVC-3DIL-B Brake fluid: Motorcraft DOT 4 Low Viscosity (LV) High Performance PM-20
Manual transmission fluid: Motorcraft Full Synthetic Manual Transmission Fluid XT-M5-QS Windshield washer fluid (U.S. and Mexico): Motorcraft Premium Windshield Wash Concentrate with Bitterant ZC-32-B2
Windshield washer fluid (Canada): Motorcraft Premium Quality Windshield Washer Fluid CXC-37-(A, B, D, F) A/C refrigerant (U.S.): Motorcraft R-134a Refrigerant YN-19
A/C refrigerant (Canada): Motorcraft R-134a Refrigerant CYN-16-R A/C refrigerant (Mexico): Motorcraft R-134a Refrigerant MYN-19
A/C refrigerant compressor oil: Motorcraft PAG Refrigerant Compressor Oil YN-12-D Multi-purpose grease:

WSS-M2C945-A

WSS-M97B44-D2

WSS-M97B44-D2

WSS-M6C65-A2

WSD-M2C200-C

WSS-M14P19-A

WSS-M14P19-A

WSH-M17B19-A

WSH-M17B19-A

WSH-M17B19-A

WSH-M1C231-B

CRCSL3151ESB

239

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Capacities and Specifications

Specification

ESB-M1C93-B

--

--

--

An oil that displays this symbol conforms to current engine, emission system and fuel economy performance standards of the International Lubricants Specification Advisory Council (ILSAC). Do not use supplemental engine oil additives because they are unnecessary and could lead to engine damage that may not be covered by your vehicle warranty.

Name

Motorcraft Multi-Purpose Grease Spray XL-5
Lock cylinders (U.S.): Penetrating and Lock Lubricant XL-1
Lock cylinders (Canada): Penetrating Fluid CXC-51-A Lock cylinders (Mexico): Penetrating and Lock Lubricant MXL-1

If you use oil and fluids that do not meet the defined specification and viscosity grade, this may lead to: • Component damage which is not covered by the vehicle warranty. Longer engine cranking periods. Increased emission levels.

• • • Reduced engine performance. • Reduced fuel economy. • Degraded brake performance. We recommend Motorcraft motor oil for your vehicle. If Motorcraft oil is not available, use motor oils of the recommended viscosity grade that meet API SN requirements and display the API Certification Mark for gasoline engines. Do not use oil labeled with API SN service category unless the label also displays the API certification mark.

240

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

E142732Capacities and Specifications

Note: Ford recommends using Motorcraft DOT 4 Low Viscosity (LV) High Performance or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the recommended fluid may cause degraded brake performance and not meet the Ford performance standards. Keep brake fluid clean and dry. Contamination with dirt, water, petroleum products or other materials may result in brake system damage and possible failure. CAPACITIES AND SPECIFICATIONS - 1.6L ECOBOOST™ Capacities

WARNING

The air conditioning refrigerant system contains refrigerant R-134a under high pressure. Opening the air conditioning refrigerant system can cause personal injury. Have the air conditioning refrigerant system serviced only by qualified personnel.

Item

Engine oil Engine coolant Brake fluid

Capacity

4.3 qt (4.1 L) 6.1 qt (5.8 L)

Between MIN and MAX on brake fluid

reservoir

Manual transmission fluid (B6) Windshield washer fluid Fuel tank A/C refrigerant A/C refrigerant compressor oil * Approximate dry fill capacity. Actual amount may vary during fluid changes.

1.7 qt (1.6 L)* Fill as required 12.4 gal (47 L)

24.0 oz (0.68 kg) 5.1 fl oz (150 ml)

241

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Capacities and Specifications

Specifications Materials

Name Recommended motor oil (U.S.): Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil XO-5W20-QSP Recommended motor oil (Canada): Motorcraft SAE 5W-20 Super Premium Motor Oil CXO-5W20-LSP12
Recommended motor oil (Mexico): Motorcraft SAE 5W-20 Synthetic Motor Oil MXO-5W20-QSP Optional motor oil (U.S. and Mexico): Motorcraft SAE 5W-20 Full Synthetic Motor Oil XO-5W20-QFS Optional motor oil (Canada): Motorcraft SAE 5W-20 Synthetic Motor Oil CXO-5W20-LFS12
Engine coolant (U.S. and Mexico): Motorcraft Orange Antifreeze/Coolant Prediluted VC-3DIL-B Engine coolant (Canada): Motorcraft Orange Antifreeze/Coolant Prediluted CVC-3DIL-B Brake fluid: Motorcraft DOT 4 Low Viscosity (LV) High Performance PM-20
Manual transmission fluid: Motorcraft Dual Clutch Transmission Fluid XT-11-QDC Windshield washer fluid (U.S. and Mexico): Motorcraft Premium Windshield Wash Concentrate with Bitterant ZC-32-B2
Windshield washer fluid (Canada): Motorcraft Premium Quality Windshield Washer Fluid CXC-37-(A, B, D, F)

Specification

WSS-M2C945-A

WSS-M2C945-A

WSS-M2C945-A

WSS-M2C945-A

WSS-M2C945-A

WSS-M97B44-D2

WSS-M97B44-D2

WSS-M6C65-A2

WSS-M2C200-D2

WSS-M14P19-A

WSS-M14P19-A

242

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Capacities and Specifications

Specification

WSH-M17B19-A

WSH-M17B19-A

WSH-M17B19-A

WSH-M1C231-B

CRCSL3151ESB ESB-M1C93-B

--

--

--

We recommend Motorcraft motor oil for your vehicle. If Motorcraft oil is not available, use motor oils of the recommended viscosity grade that meet API SN requirements and display the API Certification Mark for gasoline engines. Do not use oil labeled with API SN service category unless the label also displays the API certification mark.

Name

A/C refrigerant (U.S.): Motorcraft R-134a Refrigerant YN-19
A/C refrigerant (Canada): Motorcraft R-134a Refrigerant CYN-16-R A/C refrigerant (Mexico): Motorcraft R-134a Refrigerant MYN-19
A/C refrigerant compressor oil: Motorcraft PAG Refrigerant Compressor Oil YN-12-D Multi-purpose grease: Motorcraft Multi-Purpose Grease Spray XL-5
Lock cylinders (U.S.): Penetrating and Lock Lubricant XL-1
Lock cylinders (Canada): Penetrating Fluid CXC-51-A Lock cylinders (Mexico): Penetrating and Lock Lubricant MXL-1

If you use oil and fluids that do not meet the defined specification and viscosity grade, this may lead to: • Component damage which is not covered by the vehicle warranty. Longer engine cranking periods. Increased emission levels.

• • • Reduced engine performance. • Reduced fuel economy. • Degraded brake performance.

243

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Capacities and Specifications

Do not use supplemental engine oil additives because they are unnecessary and could lead to engine damage that may not be covered by your vehicle warranty. Note: Ford recommends using Motorcraft DOT 4 Low Viscosity (LV) High Performance or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the recommended fluid may cause degraded brake performance and not meet the Ford performance standards. Keep brake fluid clean and dry. Contamination with dirt, water, petroleum products or other materials may result in brake system damage and possible failure.

An oil that displays this symbol conforms to current engine, emission system and fuel economy performance standards of the International Lubricants Specification Advisory Council (ILSAC). CAPACITIES AND SPECIFICATIONS - 1.6L DURATEC-16V TI-VCT (SIGMA) Capacities

WARNING

The air conditioning refrigerant system contains refrigerant R-134a under high pressure. Opening the air conditioning refrigerant system can cause personal injury. Have the air conditioning refrigerant system serviced only by qualified personnel.

Item

Engine oil Engine coolant Brake fluid

Capacity

4.3 qt (4.1 L) 6.1 qt (5.8 L)

Between MIN and MAX on brake fluid

reservoir

Automatic transmission fluid (DPS6) Manual transmission fluid (ib5) Windshield washer fluid Fuel tank

1.8 qt (1.7 L)* 2.2 qt (2.1 L)* Fill as required 12.4 gal (47 L)

244

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

E142732Capacities and Specifications

Item

Capacity

A/C refrigerant A/C refrigerant compressor oil * Approximate dry fill capacity. Actual amount may vary during fluid changes.

21.2 oz (0.6 kg) 5.1 fl oz (150 ml)

Specifications Materials

Name Recommended motor oil (U.S.): Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil XO-5W20-QSP Recommended motor oil (Canada): Motorcraft SAE 5W-20 Super Premium Motor Oil CXO-5W20-LSP12
Recommended motor oil (Mexico): Motorcraft SAE 5W-20 Synthetic Motor Oil MXO-5W20-QSP Optional motor oil (U.S. and Mexico): Motorcraft SAE 5W-20 Full Synthetic Motor Oil XO-5W20-QFS Optional motor oil (Canada): Motorcraft SAE 5W-20 Synthetic Motor Oil CXO-5W20-LFS12
Engine coolant (U.S. and Mexico): Motorcraft Orange Antifreeze/Coolant Prediluted VC-3DIL-B Engine coolant (Canada): Motorcraft Orange Antifreeze/Coolant Prediluted CVC-3DIL-B Brake fluid: Motorcraft DOT 4 Low Viscosity (LV) High Performance PM-20
Automatic transmission fluid: Motorcraft Dual Clutch Transmission Fluid XT-11-QDC

Specification

WSS-M2C945-A

WSS-M2C945-A

WSS-M2C945-A

WSS-M2C945-A

WSS-M2C945-A

WSS-M97B44-D2

WSS-M97B44-D2

WSS-M6C65-A2

WSS-M2C200-D2

245

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Capacities and Specifications

Name

Manual transmission fluid: Motorcraft Full Synthetic Manual Transmission Fluid XT-M5-QS Windshield washer fluid (U.S. and Mexico): Motorcraft Premium Windshield Wash Concentrate with Bitterant ZC-32-B2
Windshield washer fluid (Canada): Motorcraft Premium Quality Windshield Washer Fluid CXC-37-(A, B, D, F) A/C refrigerant (U.S.): Motorcraft R-134a Refrigerant YN-19
A/C refrigerant (Canada): Motorcraft R-134a Refrigerant CYN-16-R A/C refrigerant (Mexico): Motorcraft R-134a Refrigerant MYN-19
A/C refrigerant compressor oil: Motorcraft PAG Refrigerant Compressor Oil YN-12-D Multi-purpose grease: Motorcraft Multi-Purpose Grease Spray XL-5
Lock cylinders (U.S.): Penetrating and Lock Lubricant XL-1
Lock cylinders (Canada): Penetrating Fluid CXC-51-A Lock cylinders (Mexico): Penetrating and Lock Lubricant MXL-1

Specification

WSD-M2C200-C

WSS-M14P19-A

WSS-M14P19-A

WSH-M17B19-A

WSH-M17B19-A

WSH-M17B19-A

WSH-M1C231-B

CRCSL3151ESB ESB-M1C93-B

--

--

--

246

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Capacities and Specifications

Note: Ford recommends using Motorcraft DOT 4 Low Viscosity (LV) High Performance or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the recommended fluid may cause degraded brake performance and not meet the Ford performance standards. Keep brake fluid clean and dry. Contamination with dirt, water, petroleum products or other materials may result in brake system damage and possible failure.

If you use oil and fluids that do not meet the defined specification and viscosity grade, this may lead to: • Component damage which is not covered by the vehicle warranty. Longer engine cranking periods. Increased emission levels.

• • • Reduced engine performance. • Reduced fuel economy. • Degraded brake performance. We recommend Motorcraft motor oil for your vehicle. If Motorcraft oil is not available, use motor oils of the recommended viscosity grade that meet API SN requirements and display the API Certification Mark for gasoline engines. Do not use oil labeled with API SN service category unless the label also displays the API certification mark.

An oil that displays this symbol conforms to current engine, emission system and fuel economy performance standards of the International Lubricants Specification Advisory Council (ILSAC). Do not use supplemental engine oil additives because they are unnecessary and could lead to engine damage that may not be covered by your vehicle warranty.

247

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

E142732Audio System

GENERAL INFORMATION Radio Frequencies and Reception Factors

Distance and Strength

Terrain

Station overload

Radio reception factors

The further you travel away from an FM station, the weaker the signal and the weaker the reception. Hills, mountains, tall buildings, bridges, tunnels, freeway overpasses, parking garages, dense tree foliage and thunderstorms can interfere with the reception. When you pass near a radio transmission tower, a stronger signal can override a weaker signal and can cause interfer- ence in the audio system.

MP3 and WMA Track and Folder Structure Audio systems capable of recognizing and playing MP3 and WMA individual tracks and folder structures work as follows: •

There are two different modes for MP3
and WMA disc playback: MP3 and WMA track mode (system default) and MP3 and WMA folder mode.

• MP3 and WMA track mode ignores any folder structure on the MP3 and WMA disc. The player numbers each MP3
and WMA track on the disc (noted by the MP3 or WMA file extension) from T001 to a maximum of T255. The maximum number of playable MP3 and WMA files may be less depending on the structure of the CD and exact model of radio present.

CD and CD Player Information Note: CD units play commercially pressed 4.75-inch (12 centimeter) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Note: Do not insert CDs with homemade paper (adhesive) labels into the CD player as the label may peel and cause the CD to become jammed. You should use a permanent felt tip marker rather than adhesive labels on your homemade CDs. Ballpoint pens may damage CDs. Please contact an authorized dealer for further information. Note: Do not use any irregularly shaped discs or discs with a scratch protection film attached. Always handle discs by their edges only. Clean the disc with an approved CD cleaner only. Wipe it from the center of the disc toward the edge. Do not clean in a circular motion. Do not expose discs to direct sunlight or heat sources for extended periods.

248

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Audio System

• MP3 and WMA folder mode represents

a folder structure consisting of one level of folders. The CD player numbers all MP3 and WMA tracks on the disc (noted by the MP3 or WMA file extension) and all folders containing MP3 and WMA files, from F001 (folder) T001 (track) to F253 T255.

• Creating discs with only one level of

folders helps with navigation through the disc files.

If you are burning your own MP3 and WMA discs, it is important to understand how the system reads the structures you create. While various files may be present, (files with extensions other than MP3 and WMA), only files with the MP3 and WMA extension are played; other files are ignored by the system. This enables you to use the same MP3 and WMA disc for a variety of tasks on your work computer, home computer and your in-vehicle system.

In track mode, the system displays and plays the structure as if it were only one level deep (all MP3 and WMA files play, regardless of being in a specific folder). In folder mode, the system only plays the MP3 and WMA files in the current folder. AUDIO UNIT - VEHICLES WITH: AM/FM/CD

WARNING

Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.

249

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Audio System

Eject: Press the button to eject a CD. Cursor arrows: Press a button to scroll through on-screen choices. CD slot: Where you insert a CD. OK: Press the button to confirm on-screen selections. Clock: Press to set the time. Use the H and M buttons outside the audio display to adjust the hours and minutes. Press OK to finish. (The clock can also be set by pressing MENU, then scrolling to the clock settings menu.) Tune: Press the button to manual tune on AM and FM wavebands. Numeric keypad: Press the button to recall a previously stored station. To store a favorite station press and hold until the sound returns. Seek up: Press the button to go to the next station up the radio frequency band or the next track on a CD.

250

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

E156613EDOFGKLMNJHICABAudio System

On, Off and Volume: Press the button to switch the audio system on or off. Turn the dial to adjust the volume. Seek down: Press the button to go to the next station down the radio frequency band or the previous track on a CD. MENU: Press the button to access different audio system features. INFO: Press the button to access radio or CD information. SOUND: Press the button to adjust the sound settings for bass, treble, middle, balance and fade. MEDIA: Press the button to access the AUX and SYNC features, it will also cancel the menu or list browsing. RADIO: Press the button to select different radio bands, it will also cancel the menu or list browsing.

Station Tuning Control Seek Tuning Select a waveband and briefly press one of the seek buttons. The unit will stop at the first station it finds in the direction you have chosen. Manual Tuning 1. Press the MENU button. 2. Select RADIO mode and then Manual. 3. Use the left and right arrow buttons to tune down or up the waveband in small increments or press and hold to increment quickly, until you find a station you want to listen to.

4. Press OK to continue listening to a

station.

Scan Tuning Scan allows you to listen to a few seconds of each station detected. 1. Press the MENU button. 2. Select RADIO mode and then Scan. 3. Use the seek buttons to scan up or

down the selected waveband.

Sound Button This will allow you to adjust the sound settings (for example bass, middle and treble). 1. Press the SOUND button. 2. Use the up and down arrow buttons to

select the required setting.

3. Use the left and right arrow buttons to make the necessary adjustment. The display indicates the level selected. 4. Press the OK button to confirm the

new settings.

Waveband Button Press the RADIO button to select from the wavebands available. You can use the selector to return to radio reception when you have been listening to another source. Alternatively, press the left arrow button to display the available wavebands. Scroll to the required waveband and press OK.

251

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Audio System

2. Select Spd. Comp. Vol. 3. Use the left or right arrow button to

adjust the setting.

4. Press the OK button to confirm your

selection.

5. Press the MENU button to return. Alternative Frequencies The majority of programs that broadcast on the FM waveband have a program identification code that can be recognized by audio units. When your vehicle moves from one transmission area to another with the alternative frequencies tuning switched on, this function will search for the strongest station signal. Under certain conditions, alternative frequencies tuning may temporarily disrupt normal reception. When selected, the unit continually evaluates signal strength and if a better signal becomes available, the unit will switch to that alternative. It mutes while it checks a list of alternative frequencies and if necessary, it will search once across the selected waveband for a genuine alternative frequency. It will restore radio reception when it finds one or if one is not found, the unit will return to the original stored frequency. When selected, AF will be shown in the display. 1. Press the MENU button. 2. Select Audio Settings. 3. Scroll to Alternat. freq. or Alt.

Frequency and turn on or off with the OK button.

4. Press the MENU button to return.

4. Press OK to continue listening to a

station.

Station Preset Buttons This feature allows you to store your favorite stations, they can be recalled by selecting the appropriate waveband and pressing one of the preset buttons. 1. Select a waveband. 2. Tune to the station required. 3. Press and hold one of the preset

buttons. A progress bar and message will appear. When the progress bar completes the station has been stored. The audio unit will also mute momentarily as confirmation.

You can repeat this on each waveband and for each preset button. Note: When you drive to another part of the country, stations that broadcast on alternative frequencies and are stored on preset buttons, may be updated with the correct frequency and station name for that area. Autostore Control Note: This will store up to a maximum of the six strongest signals available, either from the AM or the FM waveband and overwrite the previously stored stations. You can also store stations manually in the same way as other wavebands. • Press and hold the RADIO button. • When the search is complete, sound is restored and the strongest signals are stored on the autostore presets.

Automatic Volume Control When available, automatic volume control adjusts the volume level to compensate for engine noise and road speed noise. 1. Press the MENU button and select

Audio Settings.

252

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

Audio System

Note: An integrated multi function display is situated above the unit. This shows important information regarding control of your system. Additionally, there are various icons placed around the display screen which light up when a function is active, for example CD, Radio or Aux.

AUDIO UNIT - VEHICLES WITH: AM/FM/CD/SYNC WARNING

Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.

253

Fiesta (CCT) Canada/United States of America, enUSA, First Printing

E156629KJEDUFHIGQRSTNOPLMCABAudio System