2008 Ford F 150 Owners Manual

Use only soft cups in the cupholder. Hard objects can injure you in a collision.

OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package. The overhead console can come on rails, which can be removed by the customer, or it can come as a non-rail component of the headliner, which cannot be removed. If your vehicle is equipped with a overhead console rail system, there are several features that can be operated. 1. To open the bins, move the center latch forward which will allow the door to be opened. 2. The latches on the side of the bins are to enable the user to remove the bin or add a dealer purchased feature. Sliding the bins on the rails may cause damage to the headliner. The removable bins are to be snapped into place not slid.

104

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Storage compartment Press the release on the door to open the storage compartment. The storage compartment may be used to secure sunglasses or a similar object. The front bin may be used to store small objects.

Overhead Storage Bins

• When on the overhead rail, adjacent bins must be pinned together. Bins adjacent to the End Cap must be pinned to the End Cap. Bins without pin attachments should not be placed on the overhead rail.

Failure to pin the bins together can allow the bins to become separated from the rail under certain conditions.

105

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Bin Removal Attach and remove bins from the rail using the following instructions: Place both palms on the underside of the storage bin, avoiding the storage bin door.

Push upwards with palms.

106

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

While pushing upwards with palms, grip the side latches with fingers and squeeze.

Driver Controls

With pressure applied with palms and side latches squeezed down, pull downward on the entire storage bin and remove.

107

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power point is located on the instrument panel. Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W. If the power point or cigar lighter socket is not working, a fuse may have blown. Refer to Fuses and relays in the Roadside Emergencies chapter for information on checking and replacing fuses. To have full capacity usage of your power point, the engine is required to be running (in a safe manner) to avoid unintentional discharge of the battery. To prevent the battery from being discharged: • do not use the power point longer than necessary when the engine is • do not leave battery chargers, video game adapters, computers and other devices plugged in overnight or when the vehicle is parked for extended periods.

not running,

An additional auxiliary power point is located on the lower rear side of the center console. The power point is accessible from the rear seats. Always keep the power point caps closed when not being used.

108

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Cigarette/Cigar lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by your warranty.

Cupholder/Ashtray (if equipped) The cupholder/ashtray is located on the instrument panel. To open cupholder/ashtray, push in on the door and release. The door will spring out 1/4+ inches. Then pull cupholder/ashtray assembly out the remaining distance to utilize. To close, push assembly in completely and release. Ashtray (if equipped) The ashtray is located on the instrument panel. To open ashtray, push in on the door and release. The ashtray assembly will tip out. To close, push assembly in completely and release.

109

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

POWER WINDOWS (IF EQUIPPED)

Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure

themselves.

When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in

the proximity of the window openings.

Press and hold the bottom part of the rocker switch to open the window. Press and hold the top part of the rocker switch to close the window.

Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise. This noise can be alleviated by lowering a front window approximately two to three inches.

One touch down Allows the driver’s window to open fully without holding the control down. Press completely down on the bottom part of the rocker switch and release quickly. Press the rocker switch again to stop.

Window lock (if equipped) The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the left side of the control.

110

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Note: The rear window switches will not illuminate when the window control is in the LOCKED position. Press the right side to restore the window controls.

Power Sliding Back Window (if equipped) To operate the power sliding back window, the ignition switch must be in the Run or Accessory position. • Press and hold the bottom part of the rocker switch to open window all the way to the full open position.

• Press and hold the top part of the

rocker switch to close the window.

When operating the power sliding back window you must ensure all rear seat occupants and/or cargo are not in the proximity of

the back window.

Do not leave children unattended in the vehicle and do not let children play with the power sliding back window. They may

seriously injure themselves.

Accessory delay (if equipped) With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened.

INTERIOR MIRROR The interior rear view mirror has two pivot points on the support arm which lets you adjust the mirror UP or DOWN and from SIDE to SIDE.

Do not adjust the mirror while the vehicle is in motion.

111

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Automatic dimming interior rear view mirror (if equipped) Your vehicle may be equipped with an interior rear view mirror that has an auto-dimming function (optional on the driver’s side exterior mirror). The electronic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the interior mirror. When the interior mirror detects bright light from behind the vehicle, the interior rear view mirror and the driver’s side exterior mirror (if equipped) will automatically adjust (darken) to minimize glare. The mirrors will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up. Do not block the sensors on the front and back of the interior rear view mirror since this may impair proper mirror performance. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. Note: If equipped with a Reverse Camera System, a video image will display in the mirror when the vehicle is put in (R) reverse. As you shift into any other gear from (R) Reverse, the image will remain for a few seconds and then turn off. Refer to Reverse Camera System in the Driving chapter.

EXTERIOR MIRRORS

Power side view mirrors (if equipped) To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place.

112

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Telescoping trailer tow mirrors (if equipped) The telescoping feature allows the mirror to extend approximately 3.5 inches (90 mm). This feature is especially useful to the driver when towing a trailer. Pull the mirrors inward carefully when driving through a narrow space.

Fold-away mirrors (if equipped) Fold the side mirrors in carefully before driving through a narrow space, like an automatic car wash. Powerfold mirrors (if equipped) With powerfold mirrors, you can fold the side mirrors using the power mirror switch. 1. Rotate the switch to the center/neutral position. 2. Momentarily pull the switch rearward to auto fold in. 3. Momentarily pull the switch rearward again to fold back to design position. The powerfold mirrors may be moved inward/outward manually. However, if a mirror is moved manually, it will need to be reset. A mirror which has not been reset may appear to be loose. To reset: with the switch in the center position, momentarily pull the switch rearward to fold the mirrors in. An audible ⬙click⬙ will be heard indicating re-synchronization. If the click is not heard, use the switch to fold the mirrors out, then in, until the click is heard. After that, the mirrors will operate normally until they are again moved manually. Note: Ten or more switch activations within 1 minute, or repeated folding/unfolding of the mirrors while holding the switch rearward during the full travel may cause the system to disable the fold/unfold function to protect motors from overheating. Should this occur, wait approximately 3 minutes for the system to reset and function to return to normal.

113

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Heated outside mirrors (if equipped) Heated mirrors remove ice, mist and fog. To activate the heated mirrors, press the rear defrost button R located on the climate control panel. Refer to Rear window defrost in the Climate Controls chapter for more information.

On vehicles not equipped with rear defrost, press the heated mirror control located on the climate control panel, refer to the Climate Controls chapter for more information. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.

Exterior mounted mirror turn signal indicator (if equipped) When the vehicle turn signal is activated, the lower portion of the mirror housing will blink. This feature provides an indicator to the driver that the vehicle turn signal is working properly.

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal. • Press the bottom of the control to • Press the top of the control to adjust the pedals away from you. The adjustment allows for approximately 3 inches (76 mm) of maximum travel.

adjust the pedals toward you.

114

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.

SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal.

Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.

Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed.

3. Press the SET control and release it. 4. Take your foot off the accelerator pedal. 5. The indicator instrument cluster will turn on.

light on the

steep hill.

Note: • Vehicle speed may vary momentarily when driving up and down a • If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 10 mph (16 km/h) below

may want to apply the brakes to reduce the speed.

your set speed on an uphill, your speed control will disengage.

115

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Resuming a set speed Press the RES/RESUME control and release it. This will automatically return the vehicle to the previously set speed.

Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET control until you get to the desired speed, then release the control. You can also use the SET control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h).

• Use the accelerator pedal to get to the desired speed. When the

vehicle reaches that speed press and release the SET control.

Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the CST (coast) control until you get to the desired speed, then release the control. You can also use the CST control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 km/h).

116

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

• Depress the brake pedal until the desired vehicle speed is reached, press the SET control.

Driver Controls

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or the clutch pedal (if equipped). This will not erase your vehicle’s previously set speed, if RES/RESUME is then selected, the vehicle will return to the previously set speed.

• Press the speed control OFF control. This will erase your vehicle’s previously set speed.

Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.

STEERING WHEEL CONTROLS (IF EQUIPPED)

Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take their focus off the road. The drivers primary responsibility is the safe operation of their vehicle. Only use steering wheel controls and other devices not essential to the driving task when it is safe to do so.

These controls allow you to operate some radio and climate control features.

117

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

to select:

Audio control features Press • AM, FM1, FM2 (if equipped) • CD (if equipped) • FES/DVD (if equipped) • SAT1, SAT2 or SAT3 (Satellite • AUX (IN LINE) (if equipped) In AM, FM1, or FM2 mode: • Press and release SEEK to select the next preset station or press and hold SEEK to select the next strong station within the selected radio band.

Radio mode if equipped).

In Satellite Radio mode (if equipped): • Press and release SEEK to advance through preset channels or press

and hold SEEK to increment to the next subscribed channel.

In CD mode: • Press and release SEEK to select the next track selection on the CD or press and hold SEEK to fast forward in the current track selection.

In any mode: • Press VOL + or − to adjust

volume.

Climate control features Press TEMP + or - to adjust temperature.

118

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Press FAN + or - to adjust fan speed.

Driver Controls

MOON ROOF (IF EQUIPPED) The moon roof control is located on the overhead console.

Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves.

When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the

proximity of the moon roof opening.

control. The moon roof

Note: The moon roof will open to the “comfort” position first before opening all the way. The “comfort” position helps to alleviate rumbling wind noise which may happen in the vehicle with the roof fully opened. To open the moon roof: The moon roof is equipped with a one-touch open feature. Press and release the will open to the “comfort” position. Press and release the control again to fully open. To stop the one-touch open feature press either the or To close the moon roof: The moon roof is equipped with an automatic, one-touch, express closing feature. Press and release the motion at any time during the one-touch closing, press the control again. control. The moon To vent the moon roof: Press and hold the roof must be in the closed position in order to move it into the vent position. To close, press and hold the panel stops moving.

front portion of the control. To stop

control until the glass

control again.

119

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

The moon roof has a built-in sliding shade that can be manually opened or closed when the glass panel is shut. To close the shade, pull it toward the front of the vehicle.

HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink威 Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.

When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and objects are out of

the way to prevent potential harm or damage.

Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink威 at: www.homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink威 buttons be erased for security purposes, refer to Programming in this section.

Programming Do not program HomeLink威 with the vehicle parked in the garage. Note: Your vehicle may require the ignition switch to be turned to the ACC position for programming and/or operation of the HomeLink威. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for quicker training and accurate transmission of the radio-frequency signal.

120

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

1. Position the end of your hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink威 button you wish to program (located on your visor) while keeping the indicator light in view. 2. Simultaneously press and hold both the chosen HomeLink威 and hand-held transmitter buttons until the HomeLink威 indicator light changes from a slow to a rapidly blinking light. Now you may release both the HomeLink威 and hand-held transmitter buttons. Note: Some entry gates and garage door openers may require you to replace Step 2 with procedures noted in the “Gate Operator and Canadian Programming” in this section for Canadian residents. 3. Firmly press, hold for five seconds and release the programmed HomeLink威 button up to two separate times to activate the door. If the door does not activate, press and hold the just-trained HomeLink威 button and observe the indicator light. • If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink威 button is pressed and released. • If the indicator light blinks rapidly for two seconds and then turns to a constant light continue with “Programming” Steps 4 through 6 to complete programming of a rolling code equipped device (most commonly a garage door opener). 4. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). 5. Firmly press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 6. 6. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink威 button. Repeat the press/hold/release sequence again and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink威 should now activate your rolling code equipped device. To program additional HomeLink威 buttons begin with Step 1 in the “Programming” section. For questions or comments, please contact HomeLink威 at www.homelink.com or 1–800–355–3515.

121

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing Step 1 outlined in the “Programming” section, replace Step 2 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating. • Continue to press and hold the HomeLink威 button (note Step 2 in the

“Programming” section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink威. The indicator light will flash slowly and then rapidly after HomeLink威 accepts the radio frequency signal.

• Proceed with Step 3 in the “Programming” section.

Operating the HomeLink姞 Wireless Control System To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

122

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.

HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with Step 1 in the “Programming” section. Reprogramming a single HomeLink姞 button To program a device to HomeLink威 using a HomeLink威 button previously trained, follow these steps: 1. Press and hold the desired HomeLink威 button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink威 button, follow Step 1 in the “Programming” section. For questions or comments, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

MINI MESSAGE CENTER ELECTRONIC COMPASS/TEMPERATURE DISPLAY (IF EQUIPPED) Outside air temperature The outside temperature display is contained in the instrument cluster and displays all the time, except when a warning message is present. To turn the display off or change the display from English to Metric see your authorized dealer. Compass The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antennas. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy.

123

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass calibration adjustment. Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone adjustment. Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Turn ignition to the ON position. 3. Start the engine.

23

15

14
13
12

7 8 9 1011

4. Press the ODO reset button in the cluster, hold for six seconds and release. You will see that ZONE appears in the instrument cluster display. 5. Press and release the button until the desired zone number appears. Note: The range of zone values are from 01 to 15 and “wraps” back to 01. 6. When you get to the desired ZONE number, hold the button down to “lock in” the new value. The cluster display will return to the “normal” mode when the button has not been pressed for 6 seconds. Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut.

124

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

1. Start the vehicle. 2. To enter the compass calibration mode, press and hold the button for greater than eight seconds. The display will then show CAL in the display window. 3. Drive the vehicle slowly (less than 3 mph [5 km/h]) in circles until CAL indicator turns off. As many as 5 complete circles may be required. 4. The compass is now calibrated.

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status preceded by a brief indicator chime. The system will also notify you of potential vehicle problems with a display of system warnings followed by a long indicator chime. If equipped with an outside temperature display, it will display in the instrument cluster all the time, except when a warning message is present.

Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu.

Info menu This control displays the following control displays: • Odometer/Compass • Trip odometer/Odometer/Compass • Distance to Empty

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

125

Driver Controls • Average Fuel Economy • Trip Elapsed Drive Time Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter.

Compass display The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy. Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass zone/calibration adjustment. Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone/calibration adjustment. Compass zone/calibration adjustment 1. Determine your magnetic zone by referring to the zone map. 2. Turn ignition to the ON position. 3. Start the engine. 4. From Info menu, select the Compass/Odometer function. (Do not select Trip, DTE, or AFE. The top of the message center must be blank).

23

14
13
12

15

7 8 9 1011

5. Press and hold the SETUP and RESET controls until the message center display changes to show the current zone setting (XX).

126

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

6. Press the RESET, then press SETUP control repeatedly until the correct zone setting for your geographic location is displayed on the message center. The range of zone values are from 01 to 15 and “wraps” back to 01. 7. To exit the zone setting mode, and to “lock in” your change, press and release the RESET control.

Perform compass calibration in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 8. Press the RESET control to start the compass calibration function. 9. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CIRCLE SLOWLY TO CALIBRATE display changes to CALIBRATION COMPLETED. It will take up to five circles to complete calibration. 10. The compass is now calibrated.

Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. The DTE function will display LOW FUEL LEVEL and sound a tone for one second when you have approximately 50 miles (80 km) to empty. If you RESET this warning message, this display and tone will return within 10 minutes.

127

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is reinitialized to a factory default value if the battery is disconnected.

Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/ 100 km. If you calculate your average fuel economy by dividing 100 miles traveled by gallons of fuel used (kilometers traveled by liters used), your figure may be different than displayed for the following reasons: • Your vehicle was not perfectly level during fill-up • Differences in the automatic shut-off points on the fuel pumps at • Variations in top-off procedure from one fill-up to another • Rounding of the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the RESET control after setting the speed control to get accurate highway fuel economy readings.

service stations

Trip elapsed drive time Select this function from the INFO menu to display a timer. To operate the Trip Elapsed Drive Time perform the following: 1. Press and release RESET in order to start the timer. 2. Press and release RESET to pause the timer. 3. Press and hold RESET for 2 seconds in order to reset the timer.

128

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Setup menu Press this control for the following displays: • System Check • Units (English/Metric) • Autolock • Autolamp Delay • Language System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for three seconds. Pressing the RESET control cycles the message center through each of the systems being monitored. The sequence of the system check report and how it appears in the message center is as follows: 1. FUEL LEVEL 2. ENGINE TEMP 3. OIL PRESSURE 4. BRAKE FLUID LEVEL 5. CHARGING SYSTEM Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric. Autolocks This feature automatically locks all vehicle doors when the vehicle is shifted into any gear, putting the vehicle in motion.

129

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

1. To disable/enable the autolock feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the autolocks ON or OFF. Autolamp delay This feature keeps your headlights on for up to three minutes after the ignition is switched off. 1. To disable/enable the autolamp delay feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to select the new Autolamp delay values of >0, >10, >20, >30, >60, >90, >120 or >180. Language 1. Select this function from the SETUP menu for the current language to be displayed.

2. Pressing the RESET control cycles the message center through each of the language choices.

3. Press and hold the RESET control to set the language choice.

System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4
seconds.

130

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message. Warning messages that have been reset are divided into two categories: • They will reappear on the display ten minutes from the reset. • They will not reappear until an ignition OFF-ON cycle has been

completed.

Status Warning can be reset Warning returns after 10 minutes

This acts as a reminder that these warning conditions still exist within the vehicle. Warning display Door ajar Low fuel level Check charging system Check traction control™ Low brake fluid level Low oil pressure Check engine temperature Reduced engine power Stop engine safely Check fuel cap Transmission malfunction Low tire pressure (if equipped) Tire pressure monitor fault (if equipped) Tire pressure sensor fault (if equipped) Engine failsafe mode DOOR AJAR. Displayed when a door is not completely closed. TRANSMISSION MALFUNCTION. Displayed when the transmission is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.

Warning returns after the ignition key is turned from OFF to ON.

131

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

CHECK ENGINE TEMPERATURE. Displayed when the engine coolant is overheating. Stop the vehicle as soon as safely possible, turn off the engine and let it cool. Check the coolant and coolant level. Refer to Engine coolant in the Maintenance and Specifications chapter. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.

Never remove the coolant reservoir cap while the engine is running or hot.

REDUCED ENGINE POWER. Displayed when the engine is overheating. Stop the vehicle as soon as safely possible, turn off the engine. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. STOP ENGINE SAFELY. Displayed when the engine is overheating. Stop the vehicle as soon as safely possible, turn off the engine. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. LOW FUEL LEVEL. Displayed as an early reminder of a low fuel condition. CHECK CHARGING SYSTEM. Displayed when the electrical system is not maintaining proper voltage. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as soon as possible. If the warning stays on or comes on when the engine is operating at normal speeds, have the electrical system checked as soon as possible. CHECK TRACTION CONTROL™. Displayed when the Traction Control™ system is not operating properly. If this message is displayed on the message center the Traction Control™ system will be partially operable. If this warning stays on, contact your authorized dealer for service as soon as possible. For further information, refer to Traction control™ in the Driving chapter. LOW BRAKE FLUID LEVEL. Indicates the brake fluid level is low and the brake system should be inspected immediately. Refer to Brake fluid reservoir in the Maintenance and Specifications chapter. LOW OIL PRESSURE. Displayed when the engine oil pressure is low. If this warning message is displayed, check the level of the engine oil. Refer to Engine oil in the Maintenance and Specifications chapter for information about adding engine oil. If the oil level is OK and this warning persists, shut down the engine immediately and contact your authorized dealer for service.

132

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

CHECK FUEL CAP. Displayed when the fuel filler cap is not properly installed. Check the fuel filler cap for proper installation. Refer to Fuel filler cap under the Fuel information section in the Maintenance and Specifications chapter. LOW TIRE PRESSURE (if equipped). Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. TIRE PRESSURE MONITOR FAULT (if equipped). Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. TIRE PRESSURE SENSOR FAULT (if equipped). Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to Understanding Your Tire Pressure Monitoring System in the Tires, Wheels and Loading chapter. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. ENGINE FAILSAFE MODE. Displayed when the engine has defaulted to a ’limp-home’ operation. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. DATA ERR. These messages indicate improper operation of the vehicle network communication between electronic modules. • Fuel computer • Charging system • Autolamp delay • Auto locks • Brake fluid • Compass • Outside temperature • Engine sensor Contact your authorized dealer as soon as possible if these messages occur on a regular basis.

133

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

POSITIVE RETENTION FLOOR MAT

Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the

brake pedals.

Position the floor mat so that the eyelet is over the pointed end of the retention post. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.

TAILGATE LOCK (IF EQUIPPED) Your vehicle may be equipped with a tailgate lock designed to help prevent theft of the tailgate. • Insert ignition key and turn to the • Turn ignition key to the left to

right to engage lock.

unlock.

134

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Tailgate removal Your tailgate is removable to allow more room for loading. Note: If equipped with a Reverse Camera System (RCS), do steps 1
through 3 before removing the tailgate. 1. Before removal of the tailgate, locate and disconnect the tailgate in-line connector under the pickup box on the right-hand side of the vehicle near the spare tire 2. Install a protective cap (located in the glove box) onto the vehicle in-line RCS connector. 3. Partially lower tailgate and carefully feed tailgate harness up through the truck box and the bumper. Secure the tailgate harness onto the vehicle box. 4. Lower the tailgate. 5. Use a screwdriver to pry the spring clip (on each connector) past the head of the support screw. Disconnect cable. 6. Disconnect the other cable. 7. Lift tailgate to a 45-degree angle from horizontal. 8. Lift right side off of its hinge. 9. Lift tailgate to a 80-degree angle from horizontal. 10. Remove tailgate from left side hinge by sliding tailgate to the right. To install, follow the removal procedures in reverse order.

135

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

BED EXTENDER (IF EQUIPPED) Your vehicle may be equipped with a bed extender designed to extend the pickup box for larger loads. To extend the bed extender: 1. Lower tailgate. 2. Pull the lever on each side of the bed extender to release it from the pickup box. 3. Lift the bed extender over onto the tailgate.

4. Evenly push down on the bed extender and push the lever in on each side locking it in place. To stow the bed extender, follow steps one through four in reverse order. The bed extender may be used to secure a load of up to 100 lb (46 kg) on the tailgate. The bed extender should always be kept in the stowed position with the tailgate closed when not in use. Activating bed extender Theft Deterrent Device: The following procedure can be done with the bed extender in the stowed or extended position. 1. Locate the Phillips head screw in the middle of the vertical brace in front of the locking clip. 2. Turn the screw counterclockwise until you hear an audible click. 3. To deactivate, turn the screw clockwise until the locking clip moves freely.

136

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

To remove the bed extender: 1. Extend the bed extender. 2. Pull the lever on each side of the bed extender to unlock it. Make sure the locking clip screws are loose before removing the bed extender. 3. Press the locking clips below the middle bar and lift the bed extender out of the channels on the “D” pillar. To install the bed extender, follow the removal procedure in reverse order.

CARGO AREA FEATURES (IF EQUIPPED)

Cargo management system (if equipped) The cargo management system consists of the Cargo rail package with the following as optional accessories: • Front header bar (if equipped) • Cross bars (if equipped) • Bed divider (if equipped) • Side mounted tool bins (if equipped)

137

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Cargo rail package: The strong extruded aluminum double channel rails and four adjustable cleats are designed to hold loads up to 600 lb (272 kg) per cleat (maximum of two cleats per rail).

• Cleat positions are adjusted by pulling the knob and turning slightly to lock open. The cleat can then be moved along the rail. Once the desired position is reached, return the knob to the horizontal position. Pull the cleat side-to-side to ensure it has locked into the next available hole location.

• To remove cleat from rail, release rail endcap by pulling inboard and towards the end of the rail on the two plastic tabs located inside the tracks at each end of the rails. The plastic endcap will then release and may be removed. The cleat can then be slid out the end of the rail.

When installing cleat, reverse instructions above. Note: When replacing a cleat into the rail, make sure the oval embossed on the knob is not upside down. This will ensure that the cleat is properly oriented to accept accessory attachments.

138

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Front header bar: Spans the header area of the pickup box, providing the function of a header rail.

Driver Controls

• Attachment cleats from side rails or other attachments may be positioned in the front header bar to secure loads up to 600 lb (272 kg) per cleat (maximum of two cleats).

• Cleats and other attachments may be inserted through the access window located in the center of the header bar. These items can then be slid to either side, and secured the same way as the side rails.

139

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Cross bars: Aluminum cross bars with T-slot channels in all four sides, and a latch mechanism that allows the end supports to snap over the existing cleats. Cross bars are rated to hold loads up to 100 lb (45 kg) load evenly distributed between the two crossbars, and the T-slots are sized to accept industry-standard roof rack accessories.

shroud off of the cleat.

• To remove cross bar, lift handle on each side and lift end support • To install cross bar, align cleats directly across from each other on the same rail (upper or lower). Then place crossbar end support onto cleat and press down on each side until the latch handle cycles up and then press the handle down to secure (pull up on the bars to ensure they are securely attached). • To install accessories into T-slots, remove cross bar and turn upside down, then find the slip joint end, indicated with an arrow embossed on the bottom of the support. Using a T25 Torx driver, remove two Torx head bolts from bottom, and slide end support off of aluminum extrusion. Insert accessory into desired T-slot, and install end support. When tightening Torx head bolts, hand tightening with a Torx driver is sufficient, DO NOT over torque by using a ratchet.

140

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Bed divider: This panel will keep small items up to 400 lb (180 kg) in position in the pickup box. Also includes T-slots to allow attachment of industry-standard roof rack accessories.

Driver Controls

shroud off of the cleat.

• To remove bed divider, lift handle on each side and lift end support • To install bed divider, align cleats directly across from each other on the lower rail. Then place divider end support onto the cleats and press down on each side until the latch handle cycles up then press the handle down to secure (pull up on the divider to ensure they are securely attached). • To install accessories into T-slots, remove bed divider, then find the slip joint end, indicated with an arrow embossed on the support. Using a T25 Torx driver, remove two Torx head bolts and slide end support off of the aluminum extrusion. Insert accessory into desired T-slot and install end support. When tightening Torx head bolts, hand tightening with a Torx driver is sufficient, DO NOT over torque by using a ratchet.

141

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Side mounted tool bins: Watertight bins can be positioned at any point along the side rails and can be easily removed (even when full), and carried to wherever the contents are needed. Each bin will hold up to 60 lb (27 kg) of cargo, and has a drain plug for use as a cooler. Note: When multiple bins are placed on one side of the pickup box, the total cargo weight in all bins on that side of the pickup box cannot exceed 60 lb (27 kg).

• To access the lock, pull the tab at the base of the rubber cap to

uncover the lock. When you are done with the lock always reinstall the rubber cap on the lock to ensure proper sealing. When the bin is unlocked the rubber cap does not need to be removed to open the bin, just press the rubber cap to unlatch the lid.

• The lock cylinder is keyed to the first ignition key to be turned in the

lock. This allows one key to work all bins, even if more are ordered through the dealer. The dealer will usually key the locks during pre-delivery, but if necessary, simply remove the sticker covering the keyhole, insert ignition key and turn to the extent of travel in each direction. This key will then be the only key to unlock the bin.

• Once the key has been set, simply turn the key to the right to lock, or

to the left to unlock. When locked, the push-button will not depress when pushed. • To remove the bin from the rail, open lid and pull up on both levers located on the outboard edge (next to the pickup box top rail) until the handles are all the way up (approximately 90 degrees). Once both handles are raised, the lid may be closed. Note: Windows in the lid

142

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

will allow the handles to stick up above the lid (with the lid closed). After closing the lid, simply lift up and inboard away from the pickup box side to release bin from rail.

• To install, reverse the above instructions. Note: Remove the bins during severe off road driving to avoid damage to the cargo bins and pickup box.

If any levers are visible above the lid of the bin, the bin is not securely attached to the rail, and may become detached from the

vehicle if driven in that configuration.

143

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to the SecuriLock™ passive anti-theft system section in this chapter for more information.

POWER DOOR LOCKS (IF EQUIPPED) The power door lock controls are located on the driver and front passenger door panels. Press control to unlock all vehicle doors.

Press control to lock all vehicle doors.

Smart unlocking feature The smart unlocking feature helps prevent you from locking yourself out of your vehicle. With the key in any ignition position: • The driver’s door will

automatically unlock if it is locked by the driver’s power lock control while the driver’s door is open.

The vehicle may still be locked with the key in the ignition, and performing one of the following actions: • Pressing the manual lock button on the door. • Operating the remote entry transmitter. • Operating the keyless entry keypad. • Operating the driver’s door with a key.

144

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Autolock (if equipped) The autolock feature is available on automatic transmission vehicles with power locking. This feature will lock all the doors when: • all the doors are closed, • the ignition is in the 3 (ON) position, • you shift into any gear putting the vehicle in motion, and • the brake pedal is released and the vehicle attains a speed greater

than 5 mph (8 km/h).

The autolock feature repeats when: • any door is opened then closed while the ignition is in the 3 (ON) • the brake pedal is released and the vehicle attains a speed greater

position, and

than 5 mph (8 km/h).

Deactivating/activating autolock There are four methods to enable/disable this feature: One is through your authorized dealer, the second with a power door unlock/lock sequence, the third with the keypad, and the fourth using the message center (if equipped). Before following the activation or deactivation procedures, unlock all doors using the power door lock/unlock control and ensure all vehicle doors are closed. Power door unlock/lock procedure You must complete Steps 1–5 within 30 seconds, or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait a minimum of 30
seconds to begin again. 1. Turn the ignition to the 3 (ON) control position, then press the three times. 2. Turn the ignition to the 1 (OFF/LOCK) position, then press the control three times. 3. Turn the ignition to the 3 (ON) position; the horn will chirp to indicate the driver configuration mode has been activated. 4. Within five seconds, press chirp should be heard, indicating the system has been disabled.

control. Note: One horn

then the

145

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

control then the

control will turn the

Conversely, a horn chirp followed by a honk will indicate the system is enabled. Pressing the feature ON if it was previously OFF, or OFF if it was previously ON. The horn will chirp once if autolock was deactivated or twice (one short chirp and one long honk) if autolock was activated. 5. Turn the ignition to the 1 (OFF/LOCK) position to exit programming. Note: After exiting the driver configuration mode, the horn will chirp once to indicate a feature has been activated/deactivated. Keyless entry key pad procedure 1. Turn the ignition to the 1 (OFF/LOCK) position. 2. Close all the doors. 3. Enter 5–digit entry code 4. Press and hold the 7 • 8. While holding the 7 • 8 press the 3 • 4. 5. Release the 3 • 4. 6. Release the 7 • 8. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled. Message center procedure For information regarding the activation and deactivation of the autolocks feature using the message center, refer to Message center in the Driver Controls chapter.

CHILDPROOF DOOR LOCKS (ON VEHICLES WITH REAR DOORS) • When these locks are set, the

rear doors cannot be opened from the inside.

• The rear doors can be opened

from the outside when the doors are unlocked.

The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. • Move lock control up to engage the childproof lock. • Move control down to disengage childproof locks. 146

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The typical operating range for your remote entry transmitter is approximately 33 feet (10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle. Your vehicle is equipped with a remote entry system which allows you to: • unlock the vehicle doors without • lock all the vehicle doors without • activate the personal alarm.

a key.

a key.

If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to your authorized dealer in order to aid in troubleshooting the problem. Unlocking the doors 1. Press lamps will illuminate. 2. Press doors. Locking the doors 1. Press

and release to unlock the driver’s door. Note: The interior

and release to lock all the doors. The parklamps will flash.

and release again within three seconds to unlock all the

147

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

and release again within three seconds to confirm that all the

2. Press doors are closed and locked. Note: The doors will lock again, the horn will chirp once, and the parklamps will flash once more. If any of the doors are not properly closed the horn will make two quick chirps and the parklamps will not flash. Power door lock/unlock disable feature (if equipped) The not work from inside the vehicle when: • the ignition has been turned to the 1 (OFF/LOCK) position, and • 20 seconds elapse after all vehicle doors are closed and locked using

(unlock) features on your power door locks will

(lock) and

the remote entry transmitter, the keyless entry pad, or the power door lock control (while the accompanying door is open).

(unlock) features will work again after:

(lock) and

The • a door has become ajar, • the ignition is turned to the 3 (ON) position, or • using the UNLOCK

control on your remote entry transmitter or

unlocking via the keyless entry keypad.

button

Deactivating/activating power door lock/unlock disable feature All vehicle doors must be closed before beginning the procedure. You must complete Steps 1–5 within 30 seconds, or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait a minimum of 30 seconds to begin again. 1. Turn the ignition to the 3 (ON) position, then press the three times. 2. Turn the ignition to the 1 (OFF/LOCK) position, then press the button three times. 3. Turn the ignition to the 3 (ON) position; the horn will chirp to indicate the driver configuration mode has been activated. 4. Within five seconds, press the chirp should be heard, indicating the system has been disabled. 5. Turn the ignition to the 1 (OFF/LOCK) position to exit programming. Note: After exiting the driver configuration mode, the horn will chirp once to indicate a feature has been activated/deactivated. Car finder twice within three seconds. The horn will chirp and the turn Press lamps will flash. It is recommended that this method be used to locate your vehicle, rather than using the panic alarm.

control two times. Note: One horn

148

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

to activate the alarm. Press again or turn the ignition to 2

Sounding a panic alarm Press (ACCESSORY) or 3 (ON) to deactivate. Note: The panic alarm will only operate when the ignition is in the 1
(OFF/LOCK) position.

control will automatically move the seat and adjustable pedals to

Memory seat/adjustable pedals feature (if equipped) The remote entry system can also control the memory feature. Press the control once to unlock the driver’s door. Pressing the the desired memory position (the memory position corresponds to the transmitter being used). Activating the memory feature To activate this feature: 1. Position the seat and adjustable pedals to the positions you desire. 2. Press the SET control on the driver’s seat. 3. Within five seconds, press one control on the remote transmitter and then press the 1 or 2 control on the driver’s door panel to which you would like to associate with Driver 1
or Driver 2 positions. 4. Repeat this procedure for another remote transmitter if desired. Deactivating the memory feature To deactivate this feature: 1. Press the SET control on the driver’s door seat. 2. Within five seconds, press any control on the remote transmitter which you would like to deactivate and then press the SET control on the driver’s door panel. 3. Repeat this procedure for another remote transmitter if desired.

Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent.

149

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER.

2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board.

3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the two halves back together. Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.

Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: • Take all your vehicle’s transmitters to your authorized dealer for • Perform the programming procedure yourself. 150

programming, or

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Programming remote transmitters It is necessary to have all (maximum of six — original and/or new) of your remote transmitters available prior to beginning this procedure. If all remote entry transmitters are not present during the programming procedure, the transmitters that are not present during programming will no longer operate the vehicle. To program the transmitters yourself: Note: Ensure the brake pedal is not depressed during this sequence. • Unlock all doors using the power door lock/unlock control. Insert a key and turn the ignition from the 1 (OFF/LOCK) to the 3 (ON) position and cycle between 1
(OFF/LOCK) and 3 (ON) eight times in rapid succession (within 10 seconds) with the eighth turn ending in the 3 (ON) position. The locks will cycle to confirm that the programming mode has been entered.

• Within 20 seconds, program a remote transmitter by pressing any

button on a transmitter. The locks will cycle once to confirm that the remote transmitter has been programmed. (If more than 20 seconds pass before pressing a remote transmitter button, the programming mode will exit and the procedure will have to be repeated.) • Repeat the previous step to program additional remote transmitters. The locks will cycle once to confirm that each remote transmitter has been programmed. • When you have completed programming the remote transmitters, turn the ignition to the 1 (OFF/LOCK) position or wait 20 seconds. Again the doors will lock/unlock to confirm programming has been completed.

Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm, or when the factory set 5-digit code or your personal code are correctly entered into the keyless keypad. The illuminated entry system will turn off the interior lights if: • the ignition switch is turned to the 3 (ON) position, or

151

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security • the remote transmitter lock control is pressed, or • after 25 seconds of illumination. The dome lamp control (if equipped) must not be set to the off position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 30 minutes after the last door is closed, even if the dimmer control is on. Perimeter lighting feature (if equipped) The perimeter lighting feature illuminates the exterior of the vehicle in order to provide better visibility to the user while he or she approaches and enters the vehicle. The perimeter lighting feature activates when: • the ignition is in the 1 (OFF/LOCK) position, • the autolamp sensor determines that it is dark, and • the user activates an unlock feature, using either the remote keyless

transmitter or the keypad.

The perimeter lighting feature will illuminate the headlamps and parking lamps for 25 seconds, or until: • the ignition is turned to any position other than the 1 (OFF/LOCK) • the user activates a lock feature, using either the remote keyless

position, or

transmitter or the keypad.

Enabling/disabling the perimeter lighting feature Your vehicle comes with the perimeter lighting feature enabled. All vehicle doors must be closed before beginning the procedure. You must complete Steps 1–5 within 30 seconds, or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait a minimum of 30 seconds to begin again. 1. Turn the ignition to the 3 (ON) position, then press the three times. 2. Turn the ignition to the 1 (OFF/LOCK) position, then press the control three times. 3. Turn the ignition to the 3 (ON) position; the horn will chirp to indicate the driver configuration mode has been activated.

control

152

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

control two times. Note: One horn

4. Within five seconds, press the chirp should be heard, indicating the system has been disabled. Conversely, a horn chirp followed by a honk will indicate the system is enabled. Pressing the power door control two times again will turn the feature ON if it was previously OFF, or OFF if it was previously ON. Every two consecutive presses of the entering the configuration mode will change the enable/disable condition of the feature. 5. Turn the ignition to the 1 (OFF/LOCK) position to exit programming. Note: After exiting the driver configuration mode, the horn will chirp once to indicate a feature has been activated/deactivated.

control after successfully

KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entry keypad to: • lock all vehicle doors. • unlock only the driver’s door. • unlock all vehicle doors. • program/erase the customer keycode. • enable/disable the autolocking feature. The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’s wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer. You can also create your own 5–digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.

Anti-scan feature The keyless entry keypad is equipped with an anti-theft function called “antiscan.” The antiscan feature provides a one-minute lockout feature, where the user is unable to enter the vehicle using the keypad; this lockout occurs when a valid entry code has not been entered by the user within 7 attempts (35 consecutive button presses). During the lockout, the keypad will flash and pressing the controls on the keypad will be ignored, except for pressing the 7 • 8 and the 9 • 0 controls simultaneously, which will still lock the vehicle. The anti-scan feature will be turned off after: • one minute, when the anti-scan feature times out.

153

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security • one minute of keypad inactivity. • the • the ignition is turned from the 1 (OFF/LOCK) position to the 3 (ON) position, or from the 3 (ON) position to the 1 (OFF/LOCK) position.

control is pressed on the remote entry transmitter.

Programming a personal entry code To create your own personal entry code: 1. Enter the factory set code (keypad will illuminate when pressed). 2. Within five seconds press the 1 • 2 on the keypad. 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other. 4. After the code is entered, the locks will cycle, confirming that the new code has been set. Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personal • If you set a second personal code it will erase your first personal code. Erasing personal code 1. Enter the factory set 5–digit code. 2. Press and release 1 • 2 then, 3. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing Step 1. Your personal code is now erased and only the factory set 5–digit code will work.

code.

Unlocking and locking the doors using keyless entry keypad To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of each other. Note: The driver’s door will unlock and the interior lamps will illuminate after the factory set 5-digit code or your personal code are correctly entered. To unlock all doors, press the 3 • 4 control within five seconds. To lock all doors, press the 7 • 8 and the 9 • 0 at the same time. You do not need to enter the keypad code first. Note: The interior lamps will turn off.

154

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

SECURILOCK™ PASSIVE ANTI-THEFT SYSTEM SecuriLock™ passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Your vehicle comes with two coded keys; additional coded keys may be purchased from your authorized dealer. The authorized dealer can program your spare keys to your vehicle or you can program the keys yourself. Refer to Programming spare keys for instructions on how to program the coded key. Note: The SecuriLock™ passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded key while starting the engine. These objects will not cause damage to the coded key, but may cause a momentary issue if they are too close to the key when starting the engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded key and restart the engine.

Anti-theft indicator The anti-theft indicator is located on top of the instrument panel. • When the ignition is in the 1 (OFF/LOCK) position, the indicator will

flash once every 2 seconds to indicate the SecuriLock™ system is functioning as a theft deterrent.

• When the ignition is in the 3 (ON) position, the indicator will glow for

3 seconds to indicate normal system functionality.

If a problem occurs with the SecuriLock™ system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (ON) position. If this occurs, the vehicle should be taken to an authorized dealer for service.

155

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Automatic arming The vehicle is armed immediately after switching the ignition to the 1 (OFF/LOCK) position.

Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle.

Replacement keys If your keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to an authorized dealer. The key codes need to be erased from your vehicle and new coded keys will need to be programmed. Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys.

Programming spare keys A maximum of eight keys can be coded to your vehicle. Only SecuriLock™ keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure. If two previously programmed coded keys are not available, you must bring your vehicle to your authorized dealer to have the spare coded key(s) programmed. Please read and understand the entire procedure before you begin.

156

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

1. Insert the first previously programmed coded key into the ignition and turn the ignition from the 1 (OFF/LOCK) position to the 3 (ON) position (maintain ignition in the 3 (ON) position for at least one second, but no more than ten seconds). 2. Turn ignition from the 3 (ON) position back to the 1 (OFF/LOCK) position in order to remove the first coded key from the ignition. 3. Within ten seconds of removing the first coded key, insert the second previously programmed coded key into the ignition and turn the ignition from the 1 (OFF/LOCK) position to the 3 (ON) position (maintain ignition in the 3 (ON) position for at least one second but no more than ten seconds). 4. Turn the ignition from the 3 (ON) position back to the 1 (OFF/LOCK) position in order to remove the second coded key from the ignition. 5. Within 10 seconds of removing the second coded key, insert the new unprogrammed key (new key/valet key) into the ignition and turn the ignition from the 1 (OFF/LOCK) position to the 3 (ON) position (maintain ignition in the 3 (ON) position for at least one second, but no more than ten seconds). This step will program your new key to a coded key. 6. To program additional new unprogrammed key(s), repeat Steps 1
through 5. If successful, the new coded key(s) will start the vehicle’s engine and the theft indicator will illuminate for three seconds and then go out. If not successful, the new coded key(s) will not start the vehicle’s engine and the theft indicator will flash on and off and you may repeat Steps 1
through 5. If failure repeats, bring your vehicle to your authorized dealer to have the new spare key(s) programmed.

157

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

SEATING Notes:

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.

After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.

Adjustable head restraints Head restraints help to limit head motion in the event of a rear collision. Adjust your head restraint so that it is located directly or as close as possible behind your head. The head restraints can be moved up and down.

Push control to lower head restraint.

158

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Front seat • Lift the track release bar to move

the seat forward or rearward. Make sure that the seat is relatched into place.

• Pull the release lever handle

located on the side of the seat up to move the seatback forward or backward.

Using the armrest (if equipped) Push the release control to move the armrest up or down.

Using the manual lumbar support For more lumbar support, turn the lumbar support control toward the front of vehicle. For less lumbar support, turn the lumbar support control toward the rear of vehicle.

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

159

Seating and Safety Restraints

Adjusting the front power seat (if equipped)

Never adjust the driver’s seat or seatback when the vehicle is moving.

Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor.

To reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in the seatback map pocket (if

equipped) when a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the “passenger airbag off” or “pass airbag off” indicator lamp for proper airbag status. Refer to Front passenger sensing system section for additional details. Failure to follow these instructions may interfere with the front passenger seat sensing system.

160

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

The control is located on the outboard side of the seat cushion. Press the front or rear portion to tilt the seat.

Press the control to move the seat forward, backward, up or down.

Memory seats/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat and adjustable pedals to two programmable positions. The memory seat control is located on the driver’s seat. • To program position one, move the driver seat and adjustable pedals to the desired position. Press the SET control. The SET control indicator light will briefly illuminate. While the light is illuminated, press control 1.

• To program position two, repeat the previous procedure using control 2. A position can only be recalled when the transmission gearshift is in Park. A memory position may be programmed at any time.

161

2008 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Heated seats (if equipped)

Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury,

medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion, because this may cause the seat heater to overheat. Do not puncture the seat with pins, needles, or other pointed objects because this may damage the heating element which may cause the seat heater to overheat. An overheated seat may cause serious personal injury.

Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on the

seat. Allow the seat to dry thoroughly.

To operate the heated seats, do the following: • Push control located on the

instrument panel to set at high heat.

• Push control again to set at low heat. • Push again to deactivate. The indicator light on the control will illuminate when activated. The system automatically shuts off after 10 minutes.

REAR SEATS

Head restraints The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the