2003 Ford F 150 Owners Manual

position and

Foglamp control (if equipped) The foglamps can be turned on only when the headlamp control is in the beams are not turned on. Pull headlamp control towards you to turn foglamps on. The foglamp will illuminate. indicator light

position and the high

44

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Lights

Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position and • the headlamp control is in the OFF, parking lamp or autolamp

position.

Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system does not activate with your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.

High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate.

Flash to pass Pull toward you slightly to activate and release to deactivate.

45

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Lights

PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps. Move the control to the full down position, past detent, to turn off the interior lamps.

AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician.

TURN SIGNAL CONTROL • Push down to activate the left • Push up to activate the right turn

turn signal.

signal.

46

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Lights

INTERIOR LAMPS

Map lamps To turn on the map lamps, press the control next to each lamp.

If equipped with a moon roof, press the control next to the map lamp to illuminate the lamp.

AUTO

ROOF

Rear dome lamp (if equipped) The dome lamp lights when the control is in the DOOR (left) position, any door is open, the instrument panel switch is pushed past the detent and when any of the remote entry controls are pressed while the ignition is off. The rear dome lamp can be turned ON (center) or OFF (right) by sliding the control.

47

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Lights

Courtesy/reading lamps The dome lamp lights when the control is in the DOOR (left) position, any door is open, the instrument panel switch is pushed past the detent and when any of the remote entry controls are pressed while the ignition is off. The reading lamps can be turned on by pressing the rocker controls next to each lamp.

Rear door lamps (if equipped) The dome lamp lights when the control is in the DOOR (left) position, any door is open, the instrument panel switch is pushed past the detent and when any of the remote entry controls are pressed while the ignition is off. The rear door lamps can be turned on by pressing the rocker controls next to each lamp.

BULBS

Replacing exterior bulbs Check the operation of all the bulbs frequently.

Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.

48

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Function

Number of

Trade number

bulbs

Lights

Headlamps Front park/turn lamps Foglamps Backup lamp Rear stop/turn/sidemarker/tail lamp High-mount brakelamp Cargo lamp License plate lamp Signal mirror lamp (if equipped) Running board lamp (if equipped) All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer 1Harley Davidson package uses bulb number H1 12V

9007
3157K 91451
3156K 3457K

912
912
168

168

906/921

Replacing headlamp bulbs 1. Make sure that the headlamp control is in the OFF position and open the hood. 2. At the back of the headlamp, pull clips rearward and up (about 3⁄4
inch) to release the headlamp assembly. 3. Slide headlamp assembly forward and disconnect the electrical connector from the bulb by pulling rearward.

49

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Lights

4. Remove bulb retainer ring by turning it counterclockwise, then slide the ring off the plastic base. 5. Carefully pull bulb assembly out of headlamp assembly and replace.

Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

Install the new bulb in reverse order. Replacing front parking lamp/turn signal bulbs 1. Make sure the headlamp control is in the OFF position and open the hood. 2. Remove screw from the lamp assembly and disengage lamp assembly by pulling straight forward, to disengage two hidden snap-in retainers.

50

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Lights

3. Remove bulb socket from the parking lamp assembly by turning it counterclockwise. 4. Pull bulb straight out of socket and press in the new bulb.

Install the new bulb(s) in reverse order. Replacing tail/brake/turn signal/backup lamp bulbs 1. Make sure the headlamp control is in the OFF position. 2. Open the liftgate to expose the lamp assembly screws and remove the two bolts from the tail lamp assembly. 3. Carefully pull the lamp assembly straight rearward from the tailgate pillar to disengage two hidden snap-in retainers. (Flare side and Super Crew tail lamps are not equipped with snap-in retainers.) 4. Remove bulb socket from the lamp assembly by turning it counterclockwise. 5. Pull bulb straight out of socket and press in the new bulb. Install the new bulb(s) in reverse order.

51

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Lights

Replacing high-mount brake and cargo lamp bulbs Make sure the headlamp control is in the OFF position. 1. Remove the two screws and move the lamp assembly away from the vehicle to expose the bulb sockets. 2. Remove the bulb socket by rotating counterclockwise and pulling it out of the lamp assembly. 3. Pull the bulb straight out of the socket and push in the new bulb. Install the new bulbs in reverse order. Replacing foglamp bulbs (if equipped) 1. Make sure the headlamp control is in the OFF position. 2. Remove the bulb socket from the foglamp by turning counterclockwise. 3. Disconnect the electrical connector from the foglamp bulb. Install the new bulb in reverse order. Replacing signal mirror lamp bulbs (if equipped) For bulb replacement, see a dealer or qualified technician. Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper. To change the license plate lamp bulbs: 1. Reach behind the rear bumper to locate the bulb. 2. Twist the bulb socket counterclockwise and carefully pull to remove it from the lamp assembly. 3. Pull out the old bulb from the socket and push in the new bulb. 4. Install the bulb socket in lamp assembly by turning it clockwise.

52

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Lights

Replacing running board lamp bulbs (if equipped) The running board bulbs are located behind the running board. 1. Reach behind the center bracket of the running board to locate the bulb. 2. Twist the bulb socket counterclockwise and carefully pull to remove it from the lamp assembly. 3. Pull out the old bulb from the socket and push in the new bulb. Install the new bulb in reverse order.

53

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

Driver Controls

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Speed dependent wipers: When the wiper control is on, the speed of the wipers will automatically adjust with the vehicle speed. The faster your vehicle is travelling the faster the wipers will go. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers

will swipe three times with washer fluid.

up to ten seconds.

• a long push and hold: the wipers and washer fluid will be activated for

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from the vehicle. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 2. Attach the new wiper to the wiper arm and press it into place until a click is heard. 3. Replace wiper blades every 6 months for optimum performance.

54

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

TILT STEERING WHEEL (IF EQUIPPED) To adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position.

Never adjust the steering wheel when the vehicle is moving.

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamps.

OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package.

Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open. The storage compartment may be used to secure sunglasses or a similar object.

55

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: 1. Place Velcro hook onto side of aftermarket transmitter opposite of actuator control. 2. Place the transmitter into storage compartment, control down.

3. Place the provided height adaptors onto the back of the garage control as needed. 4. Press the garage control to activate the transmitter.

Electronic compass/temperature display (if equipped) Outside air temperature The outside temperature display is contained in the overhead console unless the vehicle is equipped with an EATC system. Refer to Electric automatic temperature control in the Climate controls chapter. The temperature display can be turned off and on by pressing the SELECT control on the overhead console. The temperature can be displayed in Centigrade or Fahrenheit by pressing the SELECT control. The ignition key must be in the ON or ACC position.

73˚ NW

56

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

If the outside temperature falls below 3°C (38°F), the display will alternate from “ICE” to the outside temperature at a two second rate for one minute. Compass The compass display is contained in the overhead console. The vehicle heading is displayed as one of N, NE, E, SE, S, SW, W and NW. The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in or on the vehicle may also affect compass accuracy. Adjustments may need to be made to the zone and calibration of the compass. Compass zone adjustment 1. Determine which magnetic zone you are in by referring to the zone map. 2. Turn the ignition to the ON position.

23

15

14
13
12

7 8 9 1011

3. Press and hold the SELECT control until VAR appears in the display, then release. The display should show the current zone number. 4. Press the SELECT control until the desired zone number appears. The display will flash and then return to normal operation. The zone is now updated.

9 VAR

57

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines: • Press and hold the SELECT control until CAL appears in the display (approximately eight seconds) and release. • Drive the vehicle slowly (less

CAL

than 5 km/h [3 mph]) in circles until CAL indicator turns off in about 2–3 complete circles.

• The compass is now calibrated.

AUXILIARY POWER POINT Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power point is located on the instrument panel. Do not plug optional electrical accessories into the cigarette lighter. Use the power point.

Auxiliary power point (Harley-Davidson F-150 only) A additional auxiliary power point is located on the lower rear side of the console. The power point is accessible from the rear seats.

58

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

Auxiliary power point (SuperCrew only) An additional auxiliary power point is located on the right side rear trim panel next to the rear seat.

CENTER CONSOLE (IF EQUIPPED) The center console offers several useful storage features. These include: • Large utility compartment • Cupholders • Coin holder slots • PalmPilot娂/PDA holder • Pen holder • Power point • Tissue holder • Cassette/CD organizer slots

Use only soft cups in the cupholder. Hard objects can injure you in a collision.

CELL PHONE USE The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However, drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits. Mobile Communication Equipment includes, but is not limited to cellular phones, pagers, portable email devices, in vehicle communications systems, telematics devices and portable two-way radios.

59

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

A driver’s first responsibility is the safe operation of the vehicle. The most important thing you can do to prevent a crash is to

avoid distractions and pay attention to the road. Wait until it is safe to operate Mobile Communications Equipment.

POWER WINDOWS (IF EQUIPPED)

When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings.

Press and hold the bottom part of the rocker switch to open the window. Press and hold the top part of the rocker switch to close the window.

One touch down Allows the driver’s window to open fully without holding the control down. Press completely down on AUTO and release quickly. Press again to stop.

Accessory delay (if equipped) With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened.

60

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

Power rear slider window (if equipped) • Press and hold the open arrow side of control to open window. • Press and hold the closed arrow side of control to close window.

MIRRORS

Automatic dimming rear view mirrors (if equipped) Your vehicle is equipped with an inside rear view mirror with an auto-dimming function. The electronic day/night mirror will change from the normal state to the non-glare state when bright lights (glare) reach the inside rear view mirror. When the inside rear view mirror detects bright light from behind the vehicle, the inside rear view mirror will automatically adjust (darken) to minimize glare. Do not block the sensor on the backside of the inside rear view mirror since this may impair proper system performance. Press the control to turn the mirror OFF or AUTO. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse)(when the mirror is on) to ensure a bright clear view when backing up.

AUTO

OFF

Power side view mirrors (if equipped) To adjust your mirrors 1. Select L to adjust the left mirror or R to adjust the right mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to disable the adjust function.

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

61

Driver Controls

(if equipped)

Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog. The mirrors are activated when the vehicle is running and the glass is below freezing. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors. Signal mirrors (if equipped) When the turn signal is activated, the outer portion of the appropriate mirror housing will blink red. This provides an additional warning to other drivers that your vehicle is about to turn.

Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash.

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal PEDALS should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal toward you or away from you. The adjustment allows for approximately 76 mm (3 inches) of maximum travel.

62

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.

SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 48 km/h (30 mph) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 48 km/h (30 mph).

Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.

Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed.

3. Press the SET ACCEL control and release it. 4. Take your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on.

ON

OFF

ON

OFF

RES

SET

ACCEL

COAST

RSM

SET

ACCEL

COAST

steep hill.

Note: • Vehicle speed may vary momentarily when driving up and down a • If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 16 km/h (10 mph) below

may want to apply the brakes to reduce the speed.

your set speed on an uphill, your speed control will disengage.

63

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

Resuming a set speed Press the RES/RSM (resume) control and release it. This will automatically return the vehicle to the previously set speed. The RES/RSM control will not work if the vehicle speed is not faster than 48 km/h (30 mph).

RES

SET

ACCEL

COAST

RSM

SET

ACCEL

COAST

RES

Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET ACCEL control until you get to the desired speed, then release the control. You can also use the SET ACCEL control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1.6 km/h (1 mph).

• Use the accelerator pedal to get to the desired speed. When the

vehicle reaches that speed press and release the SET ACCEL control.

ACCEL

COAST

COAST

ACCEL

RSM

SET

SET

Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the COAST control until you get to the desired speed, then release the control. You can also use the COAST control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1.6 km/h (1 mph).

ACCEL

COAST

COAST

ACCEL

RSM

RES

SET

SET

64

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

• Depress the brake pedal until the desired vehicle speed is reached, press the SET ACCEL control.

Driver Controls

RES

SET

ACCEL

COAST

RSM

SET

ACCEL

COAST

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or the clutch pedal (if equipped). This will • Press the speed control OFF

not erase your vehicle’s previously set speed.

control.

Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.

ON

OFF

ON

OFF

Indicator light This light comes on when either the SET ACCEL or RES controls are pressed. The vehicle speed must be at or above 48 km/h (30 mph). It turns off when the speed control OFF control is pressed, the brake or clutch is applied, or the ignition is turned to the OFF position.

CRUISE

ONE-TOUCH MOON ROOF (IF EQUIPPED) • To open, press and release the rear portion of the moon roof control. • To close, press and hold (as

desired) the front portion of the moon roof control.

• To halt motion at any point during one-touch opening, press the control a second time.

AUTO

ROOF

65

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls • To tilt into the vent position (when the glass panel is closed), press and hold the front portion of the moon roof control. To close from the vent position, press and hold the rear portion of the control until the glass panel stops moving.

• The moon roof has a sliding shade that can be manually opened or • To close the shade, pull it toward the front of the vehicle.

closed when the glass panel is shut.

Do not let children play with the moon roof. They may seriously hurt themselves.

HOMELINK姞 WIRELESS CONTROL SYSTEM WITH TRAVELNOTE姞 (IF EQUIPPED) The HomeLink威 Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most current transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.

When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and objects are out of

the way to prevent potential harm or damage.

Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink威 at: www.homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink威 buttons be erased for security purposes, refer to Programming in this section.

Programming Do not program HomeLink威 with the vehicle parked in the garage. Note: Your vehicle may require the ignition switch to be turned to the ACC position for programming and/or operation of the HomeLink威. It is

66

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

DEL

REC

PLAY

also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for quicker training and accurate transmission of the radio-frequency signal. 1. Press and hold the two outside buttons releasing only when the red light begins to flash after 20
seconds. Do not repeat step one to program additional hand-held transmitters to the remaining two HomeLink威 buttons. This will erase previously programmed hand-held transmitter signals into HomeLink威. 2. Position the end of your hand-held transmitter 2–8 cm (1–3 inches) away from the HomeLink威 button you wish to program (located on your visor) while keeping the red light in view. 3. Simultaneously press and hold both the HomeLink威 and hand-held transmitter button. Do not release the buttons until step 4 has been completed. Some entry gates and garage door openers may require you to replace step 3 with procedures noted in the “Gate Operator and Canadian Programming” section for Canadian residents. 4. The red light will flash slowly and then rapidly. Release both buttons when the red light flashes rapidly. (The rapid flashing light indicates acceptance of the hand-held transmitters’ radio frequency signals.) 5. Press and hold the just-trained HomeLink威 button and observe the red light. If the light is a constant red, programming is complete and your device should activate when the HomeLink威 button is pressed and released. Note: To program the remaining two HomeLink威 buttons, begin with step 2 in the “Programming” section — do not repeat step 1. Note: If the red light blinks rapidly for two seconds and then turns to a continuous red, proceed with steps 6 through 8 to complete programming of a rolling code equipped device. 6. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit).

PLAY

REC

DEL

67

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

7. Press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate step eight. 8. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink威 button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink威 should now activate your rolling code equipped device. To program additional HomeLink威 buttons begin with step 2 in the “Programming” section. For questions or comments, please contact HomeLink at www.homelink.com or 1–800–355–3515.

Operating the HomeLink姞 Wireless Control System To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

PLAY

REC

DEL

Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer

HomeLink威 buttons until the red indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.

REC

DEL

PLAY

HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with step 2 in the “Programming” section.

68

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

Reprogramming a single HomeLink姞 button To program a device to HomeLink威 using a HomeLink威 button previously trained, follow these steps: 1. Press and hold the desired HomeLink威 button. Do NOT release the button. 2. The red indicator light will begin to flash after 20 seconds. Without releasing the HomeLink威 button, follow step 2 in the “Programming” section. For questions or comments, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing steps 1 and 2
outlined in the “Programming” section, replace step 3 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating. • Continue to press and hold the HomeLink威 button (note step 3 in the

PLAY

REC

DEL

“Programming” section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink威. The red indicator light will flash slowly and then rapidly after HomeLink威 accepts the radio frequency signal.

• Proceed with step 4 in the “Programming” section. Operating TravelNote姞 TravelNote威 records and stores messages for up to three minutes in total length with simple controls. When you get an idea or remember something important while you’re driving, you don’t have to try to scribble it down or pull off the side of the road. All you have to do is push a button and begin speaking.

69

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

DEL

REC

PLAY

To record a message: 1. Press and release the REC button one time to start recording. (An audible tone will sound, confirming the onset of recording). 2. Press and release the REC button a second time to end recording. (An audible tone will sound again, confirming the end of recording and the red indicator light will turn off.) 3. While a message is being recorded, the indicator light will be a solid red. 4. If the message exceeds the available memory space, two tones will sound, the indicator light will flash amber and recording will end. The indicator light will flash amber and an “error” tone will sound if the REC button is pressed when memory is full. To play a message: 1. Press and release the PLAY button to play the message. 2. Press and hold the PLAY button to hear all the messages in consecutive order starting with the most recent. 3. If the PLAY button is pressed while a message is being listened to, TravelNote威 will skip to the beginning of the next message. 4. During all PLAY functions, the indicator light will be a solid green. The indicator light will flash amber and an “error” tone will sound if the PLAY button is pressed but no message is currently in memory. To delete a message: 1. Press and release the DEL button while listening to a message or shortly after. The indicator light will flash green twice. 2. To delete all recorded messages, simultaneously press and release the PLAY and REC buttons at the same time. The indicator light will flash green twice.

PLAY

PLAY

REC

REC

DEL

DEL

70

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

If the DEL button is inadvertently pressed or the time allotted (five seconds) has passed, the indicator light will flash amber and an “error” tone will sound.

Driver Controls

POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.

TAILGATE LOCK (IF EQUIPPED) Your vehicle may be equipped with a tailgate lock designed to prevent theft of the tailgate. • Insert ignition key and turn to the • Turn ignition key to the left to

right to engage lock.

unlock.

71

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

TAILGATE REMOVAL Your tailgate is removable to allow more room for loading. 1. Lower the tailgate. 2. Use a screwdriver to pry the spring clip (on each connector) past the head of the support screw. Disconnect cable. 3. Disconnect the other cable. 4. Lift tailgate to a 45 degree angle. 5. Lift right side off of its hinge. 6. Lift left side off of its hinge. To install, follow the removal procedures in reverse order. BED EXTENDER (IF EQUIPPED) Your vehicle may be equipped with a bed extender designed to extend the pickup box for longer loads. To extend the bed extender: 1. Lower tailgate. 2. Pull the round knobs on each side of the extender to release it from the pickup box. 3. Pivot extender on to the tailgate.

4. Evenly push down on the extender and push the round knobs in on each side locking it in place. Green markings on the shaft indicate the locked position. The locking clip screws below the middle bar can be tightened counterclockwise for extra security. Note: If the red marking on the shaft is visible, the bed extender is not locked or properly secured.

72

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

To stow the bed extender, follow steps one through four in reverse order. The bed extender may be used to secure a load of up to 46 kg (100 lbs.) on the tailgate. The bed extender should always be kept in the stowed position with the tailgate closed when not in use. When driving the vehicle off road, the bed extender should be removed and the tailgate closed. To remove the bed extender: 1. Extend the bed extender. 2. Pull the round knobs on each side of the extender to unlock it. Make sure the locking clip screws are loose before removing the extender. 3. Press the locking clips below the middle bar on each side and lift the extender out of the bed. To install the bed extender, follow the removal procedure in reverse order.

TONNEAU COVER (IF EQUIPPED) The tonneau cover has been designed to maximize fuel economy and should be fully installed whenever possible. The cover can be rolled up and stowed behind the cab, or removed completely from the vehicle. • To avoid damage to the cover, do not operate the vehicle unless the cover is fully installed, or securely stowed. The removal and stowage for styleside and flareside vehicles are basically the same except where noted. To remove or stow the cover: 1. Styleside only: In cold weather lower tailgate and release the levers on each side of the rear rail to release tension on the cover.

73

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

2. Pull the rear corner assist loops of the cover, outward, then upward to release the tension. Lift up on the rear edge of the cover to remove it from the rear rail. 3. Pull one side of the cover outward and upward away from the side rail working from the rear to the front.

4. Starting from the opposite side of the vehicle, pull cover away from the side rail and roll the cover from rear to front. 5. Secure the cover behind the cab with two straps. The cover may be removed from the vehicle by sliding it sideways out of the front rail.

74

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

Flareside only: • Remove two cross bars from pickup box by pushing towards either • Lower tailgate, depress the levers on each side of the rear rail and

side to release tension.

remove rear rail from pickup box.

Styleside only: • Remove three cross bars from pickup box by pushing towards either side to release tension. Stow the cross bars in the notches behind the rolled cover in the pickup box. • Lower tailgate, depress the levers on each side of the rear rail and push rear rail towards the front of the pickup box securing it behind the cross bars and cover.

For installation of the cover, follow the removal procedure in reverse order. Make sure the crossbows are locked in the notches in the side rails and the rear rails are locked in position prior to cover installation.

75

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

HARD TONNEAU COVER (IF EQUIPPED) The tonneau cover has been designed to maximize fuel economy. • To avoid damage to the cover, do not operate the vehicle unless the cover is fully secured.

To open the cover: • Unlock the cover (with the key) and lift the cover up for access to the pickup box. To close the cover: • Close the cover on pickup box.

76

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

Locks and Security

KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to SecuriLock娂 Passive Anti-Theft System for more information.

POWER DOOR LOCKS (IF EQUIPPED) If the door does not unlock when the U is pressed, see Interior power door disable feature in the Remote entry section in this chapter. Press U to unlock all doors and L to lock all doors.

77

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

Childproof door locks (if equipped) When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. Move lock control up to engage the childproof lock. Move control down to disengage childproof locks.

INTERIOR TONNEAU COVER RELEASE (IF EQUIPPED) Your vehicle is equipped with a mechanical interior tonneau cover release handle that provides a means of escape for children and adults in the event they become locked inside the pickup box. Adults are advised to familiarize themselves with the operation and location of the release handle.

78

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

To open the tonneau cover from the inside, pull the “T” shaped handle and push up on the tonneau cover panel. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light. The “T” shaped handle is located on the tonneau cover panel.

Keep vehicle doors and tonneau cover locked and keep keys and remote transmitters out of a child’s reach. Unsupervised children

could lock themselves in the box and risk injury. Children should be taught not to play in vehicles.

On hot days, the temperature in the pickup box can rise very quickly. Exposure of people or animals to these high

temperatures for even a short time can cause death or serious heat-related injuries, including brain damage. Small children are particularly at risk.

REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

79

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

a key.

Your vehicle is equipped with a remote entry system which allows you to: • unlock the vehicle doors without • lock all the vehicle doors without • activate the personal alarm.

a key.

If there is any potential remote keyless entry problem with your vehicle, ensure ALL remote entry transmitters are taken to the dealership, to aid in troubleshooting.

Unlocking the doors 1. Press lamps will illuminate. 2. Press doors.

and release to unlock the driver’s door. Note: The interior

and release again within three seconds to unlock all the

and release to lock all the doors. The headlamps will flash. and release again within three seconds to confirm that all the

Locking the doors 1. Press 2. Press doors are closed and locked. Note: the doors will lock again, the horn will chirp once, and the headlamps will flash once more. If any of the doors are not properly closed the horn will make two quick chirps and the headlamps will not flash.

Power door lock disable feature (if equipped) The UNLOCK inside the vehicle when: • the ignition has been turned to the OFF position, and • 20 seconds elapse after all vehicle doors are closed and locked using

feature on your power door locks will not work from

the remote entry transmitter, the keyless entry pad, or the power door lock control (while the accompanying door is open).

80

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

feature will work again after:

The UNLOCK • a door has become ajar, • the ignition is turned to the ON position, or • using the UNLOCK

control on your remote entry transmitter or

unlocking via the keyless entry keypad.

Power door lock disable feature — activation/deactivation Please see your dealer in order to activate/deactivate this feature.

to activate the alarm. Press again or turn the ignition to ACC

Sounding a panic alarm Press or ON to deactivate. Note: The panic alarm will only operate when the ignition is in the OFF position.

Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. The typical operating range for your remote entry transmitter is approximately 10 meters (33 feet). A decrease in the operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle and • other vehicles parked next to the vehicle. To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER.

81

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board.

3. Remove the old battery. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the two halves back together. Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.

Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming. How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure.

82

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

To reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 2 (LOCK) position to 3 (OFF). 4. Cycle, eight times, rapidly (within 10 seconds) between the 3 (OFF) position and 4 (ON). Note: The eighth turn must end in the 4 (ON) position. 5. The doors will lock, then unlock, to confirm that the programming mode has been activated. 6. Within 20 seconds press any button on the remote entry transmitter. Note: If more than 20 seconds have passed you will need to start the procedure over again. 7. The doors will lock, then unlock, to confirm that this remote entry transmitter has been programmed. 8. Repeat Step 6 to program each additional remote entry transmitter. 9. Turn the ignition to the 3 (OFF) position after you have finished programming all of the remote entry transmitters. Note: After 20
seconds have passed, you will automatically exit the programming mode. 10. The doors will lock, then unlock, to confirm that the programming mode has been exited.

Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm. The illuminated entry system will turn off the interior lights if: • the ignition switch is turned to the ON position, or • the vehicle is locked using the keyless entry keypad, • the remote transmitter lock control is pressed, or • after 25 seconds of illumination. The dome lamp control (if equipped) must not be set to the OFF position for the illuminated entry system to operate.

83

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 30 minutes after the last door is closed, even if the dimmer control is on.

Autolock (if equipped) This feature will automatically lock all the doors when: • all the doors are closed, • the ignition key is in the ON position, • the gearshift lever is shifted into R reverse or a forward gear and • the brake pedal is released. This feature will also automatically relock all the doors when: • the ignition is running and any door is opened then closed, and • you put the vehicle in motion by releasing the brake pedal. Deactivating/activating the autolock feature Before following the procedure, make sure that the ignition is OFF and all vehicle doors are closed. You must complete steps 1-7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. 1. Turn the ignition key to ON. 2. Press the power door unlock control three times. 3. Turn the ignition key from ON to OFF. 4. Press the power door unlock control three times. 5. Turn the ignition back to ON. The horn will chirp. 6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. Turn the ignition to OFF. The horn will chirp once to confirm the procedure is complete.

84

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entry keypad to: • lock or unlock the doors without • activate or deactivate the

using a key.

autolock feature.

The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’s wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer. You can also create your own 5–digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation. Programming a personal entry code To create your own personal entry code: 1. Enter the factory set code. 2. Within five seconds press the 1 • 2 on the keypad. 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other. 4. The doors will again lock then unlock to confirm that your personal keycode has been programmed to the module. Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personal • If you set a second personal code it will erase your first personal code. Erasing personal code 1. Enter the factory set 5–digit code. 2. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing step 1. Your personal code is now erased and only the factory set 5–digit code will work. Anti-scan feature If an incorrect code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash during this time.

code.

85

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

control on the remote entry transmitter.

The anti-scan feature will turn off after: • one minute of keypad inactivity. • pressing the • the ignition is turned to the ON position. Unlocking and locking the doors using keyless entry To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of each other. The interior lamps will illuminate after pressing the first control on the keypad. To unlock all doors, press the 3 • 4 control within five seconds. To lock all doors, press the 7 • 8 and the 9 • 0 at the same time. You do not need to enter the keypad code first. Note: The interior lamps will turn off. Activating/deactivating autolock with the keyless entry system Before following the activation or deactivation procedures, make sure that the anti-theft system (if equipped) is not armed, the ignition is off, and all vehicle doors are closed. 1. Turn the ignition to the OFF position. 2. Close all vehicle doors. 3. Enter the five-digit entry code. 4. Press and hold the 7 • 8 control. While holding the 7 • 8 control, press and hold the 3 • 4 control. 5. Release the 3 • 4 control. 6. Release the 7 • 8 control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. To re-activate autolock, repeat steps 1–6.

SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock娂 passive anti-theft system is an engine immobilization system. This system is designed to prevent the engine from being started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Your vehicle comes with two coded keys; additional coded keys may be purchased from your dealer. The dealer can program your spare keys to

86

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

your vehicle or you can program the keys yourself. Refer to Programming spare keys for instructions on how to program the coded key. Note: The SecuriLock娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded key while starting the engine. These objects will not cause damage to the coded key, but may cause a momentary issue if they are too close to the key when starting the engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded key and restart the engine.

Theft indicator The theft indicator is located in the instrument cluster. • When the ignition is in the OFF position, the indicator will flash once every 2 seconds to indicate the SecuriLock娂 system is functioning as a theft deterrent. • When the ignition is in the ON position, the indicator will glow for 3

seconds, then turn off, to indicate normal system functionality.

If a problem occurs with the SecuriLock娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the ON position. If this occurs, the vehicle should be taken to an authorized dealer for service.

Automatic arming The vehicle is armed immediately after switching the ignition to the 3
(OFF) position. The THEFT indicator will flash every two seconds when the vehicle is armed.

Automatic disarming Switching the ignition to the 4 (ON) position with a coded key disarms the vehicle.

87

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security • The THEFT indicator will illuminate for three seconds and then go • If the THEFT indicator stays on for an extended period of time or

out.

flashes rapidly, have the system serviced by your dealer.

Replacement keys If your keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to a dealership. The key codes need to be erased from your vehicle and new coded keys will need to be programmed. Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys. Programming spare keys You can program your own coded keys to your vehicle. Please read and understand the entire procedure before you begin. Tips: • A maximum of eight keys can be coded to your vehicle. • Only use Securilock娂 keys. • You must have two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible.

• If two previously programmed coded keys are not available, you must

take your vehicle to your dealer to have the spare key(s) programmed.

1. Insert a previously programmed coded key into the ignition.

2. Turn the ignition from the 3 (OFF) position to the 4 (ON) position. Keep the ignition in the 4 (ON) position for at least one second, but no more than 10 seconds.

88

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

3. Turn the ignition to the 3 (OFF) position. 4. Remove the previously programmed coded key from the ignition. 5. Within ten seconds of removing the previously programmed coded key, insert the other previously programmed coded key into the ignition. 6. Turn the ignition from the 3 (OFF) position to the 4 (ON) position. Keep the ignition in the 4 (ON) position for at least one second but not more than 10 seconds. 7. Turn the ignition to the 3 (OFF) position. 8. Remove the previously programmed coded key from the ignition. 9. Within twenty seconds of removing the previously programmed coded key, insert the unprogrammed key (new/valet key) into the ignition. 10. Turn the ignition from the 3 (OFF) position to the 4 (ON) position. Keep the ignition in the 4 (ON) position for at least one second, but no more than 10 seconds. 11. Your new, unprogrammed key is now programmed. If the key has been successfully programmed it will start the vehicle’s engine and the theft indicator light will illuminate for three seconds and then go out. If the key was not successfully programmed, it will not start your vehicle’s engine and the theft indicator light will flash on and off, or stay on for more than three seconds. If failure repeats, bring your vehicle to your dealer to have the new key(s) programmed. To program additional new unprogrammed key(s), repeat this procedure from step 1 for each additional key.

89

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Seating and Safety Restraints

SEATING Notes:

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.

Adjustable head restraints (if equipped) Head restraints help to limit head motion in the event of a rear collision. Adjust your head restraint so that it is located directly or as close as possible behind your head. The head restraints can be moved up and down.

Push control to lower head restraint.

90

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Full bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure that the seat is relatched into place. • Pull up on the lever located at the bottom of the seatback to quickly fold the seatback forward.

60/40 split bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure the seat is relatched into place. • Pull the seatback handle up to move the seat back forward or backward. • Push down the release lever (if equipped) located on the back of the seat to quickly fold the seatback forward.

91

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Captain’s chair (if equipped) • Lift the track release bar to move

the seat forward or rearward. Make sure that the seat is relatched into place.

• Pull the release lever handle

located on the side of the seat up to move the seat back forward or backward. • Push down the release lever (if equipped) located at the bottom of the seatback to quickly fold the seatback forward.

Using the manual lumbar support For more lumbar support, turn the lumbar support control toward the front of vehicle. For less lumbar support, turn the lumbar support control toward the rear of vehicle.

Adjusting the front power seat (if equipped) The control is located on the outboard side of the seat cushion. Your vehicle will only be equipped with one of the two controls shown.

92

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Press to raise or lower the front portion of the seat cushion. • Type A

• Type B

Press to raise or lower the rear portion of the seat cushion. • Type A

• Type B

93

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Press the control to move the seat forward, backward, up or down. • Type A

• Type B

Heated seats (if equipped) To operate the heated seats: • Push control located on the side • Push again to deactivate.

of the seat to activate.

The indicator light on the control will illuminate when activated.

REAR SEATS

Folding up the rear seats (if equipped — SuperCab only) The rear seatback has a split 60/40 seat. Each seat cushion can be flipped up into the seatback position. 1. Pull control to release seat cushion. 2. Rotate seat cushion up until it locks into vertical storage position.

94

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Returning the seat to seating position

Always be sure that the seat is in a latched position, whether the seat is occupied or empty. If not latched, the seat may cause

injury during a sudden stop.

1. Pull control on the side of the seat to release seat cushion from storage position. 2. Push seat cushion down until it locks into horizontal position. Folding down the rear seats (SuperCrew only) The rear seatback has a split 60/40 seat. Each seat can be folded down into the load floor position. 1. Remove the head restraint. Push the release button at the base of the head restraint post and pull the head restraint up and out.

2. Pull control to release seat.

95

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

3. Pull seatback toward front seat and down into load floor position.

4. Make sure seat is pushed all the way down and locks into position.

Returning the seat to seating position

Always be sure that the seat is in a latched position, whether the seat is occupied or empty. If not latched, the seat may cause

injury during a sudden stop.

1. Pull control on the side of the seat to release seat cushion from the load floor position.

96

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

2. Lift seatback up until it locks into vertical position.

3. Return the head restraint to its original position. If the head restraint is inserted backwards, it may lock and not be removable by using the release button. If this happens use a stiff piece of wire such as a paper clip, and insert the wire into the hole on the opposite side of the release button. Depress the release button and remove the head restraint.

Using the armrest (if equipped) Push the release control to move the armrest up or down.

97

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

SAFETY RESTRAINTS Safety restraints precautions

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

To reduce the risk of injury, make sure children sit where they can be properly restrained.

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from

injury in a collision.

All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag (SRS) is

provided.

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas

are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.

In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt.

Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that

are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.

98

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check

seat covers and buckles before you place a child anywhere near them.

Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. • Front seats

• Rear seats (if equipped)

2. To unfasten, push the release button and remove the tongue from the buckle.

99

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints • Front seats

• Rear seats (if equipped)

The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below:

Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. The front seat belt system can also be made to lock manually by quickly pulling on the shoulder belt. Rear seat belts (if equipped) cannot be made to lock up by pulling quickly on the belt.

Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt.

100

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

When to use the automatic locking mode • Anytime a child safety seat is installed in a passenger front or outboard rear seating position with Regular Cab or SuperCab. SuperCrew models include the center seating position of the second row. Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety Restraints for Children or Safety Seats for Children later in this chapter.

How to use the automatic locking mode 1. Buckle the combination lap and shoulder belt. • Front seats

• Rear seats (if equipped)

101

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

2. Grasp the shoulder portion and pull downward until the entire belt is extracted.

3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.

After any vehicle collision, the safety belt systems at all outboard seating positions (except the driver position, which does not

have this feature) must be checked by a qualified technician to verify that the automatic locking retractor feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function.

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual. Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.

Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver and front outboard passenger seating positions. The Seat Integrated Restraints (SIR) seat (which has shoulder belts attached to the corners of the front seat back) is equipped with a buckle pretensioner. Do NOT place objects between the seats, this could interfere with the functioning of the pretensioner. For the SuperCab and

102

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

CrewCab base bench seats and all Regular Cab seating positions, the safety belts are equipped with a retractor pretensioner. The driver and front outboard passenger safety belt pretensioners are designed to activate only during certain frontal or near-frontal collisions with sufficient longitudinal deceleration. A safety belt pretensioner is a device which tightens the webbing of the lap and shoulder belts during some collisions in such a way that they fit more snugly against the body. The driver and front outboard passenger safety belt system (including retractors, buckles and height adjusters) must be replaced if the vehicle is involved in a collision that results in the activation of the safety belt pretensioners. Refer to the Safety belt maintenance section in this chapter.

Failure to replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of

a collision.

Front safety belt height adjustment (if equipped) If your shoulder belts come out of the front seat back, you will not have a safety belt height adjuster. Regular Cab and SuperCab vehicles have safety belt height adjustments for the driver and front passenger. SuperCrew vehicles have these adjustments for the driver, front passenger and rear outboard passengers. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. • Regular Cab/4–door SuperCrew

103

2003 F150 (f12) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints • 4–door SuperCab (Bench seats

only)

To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place.

Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety

belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision.

Lap belts