2000 Ford Expedition Owners Manual

† Top 40
Show † With RDS activated, press the

RDS control until SHOW is displayed.

† Use the SEL control to select

TYPE, NAME or NONE.

Mutemode Press the control to mute the playing media. Press the control again to return to the playing media.

Controls and features

(cid:83)(cid:69)(cid:76)

RDS

(cid:83)(cid:69)(cid:76)

MUTE

43

Controls and features

Settingtheclock Press the RDS control until SELECT HOUR or SELECT MINS is displayed.

Use the SEL control to manually set the time. † Press † Press

hours/minutes.

to decrease

to increase

hours/minutes.

RDS

(cid:83)(cid:69)(cid:76)

Rear seat controls (if equipped) The rear seat controls allow the middle seat passengers to operate the radio, tape, CD or CD changer (if equipped).

- VOLUME +

MODE

SEEK

MEMORY

FF

SIDE 1-2

REW

To turn on the rear seat controls, press the memory preset controls 3
and 5 at the same time. The will appear in the display. Pressing 3 and 5 at the same time again will turn the rear seat controls off. If there is a discrepancy between the rear seat and the front audio controls, (such as both trying to listen to the same playing media), the front audio system will receive the desired selection.

COMP

SHUFFLE

44

Adjustingthevolume Press the + control to increase volume. Press the - control to decrease volume.

Controls and features

- VOLUME +

MODE

SEEK

MEMORY

From the rear seat controls, volume control can be set no higher than the current radio setting unless the speakers are turned off. Refer to Turning speakers on and off. Turningthespeakersonandoff Press to turn all speakers on or off.

- VOLUME +

MODE

SEEK

MEMORY

Usingheadphones Plug a 3.5 mm headphone (not included) into the speaker on/off control to operate the headphones. The speakers will cut out once the speaker on/off control is pressed. Press the control again to deactivate the headphones.

jack. Press the

45

Controls and features

Modeselect Push the MODE control to toggle between AM, FM1, FM2, tape, CD or CD changer (if equipped).

Memorypresetcontrol Push the MEMORY control successively to allow rear seat passengers to scroll through the 6
memory presets in AM, FM1 or FM2. Push the MEMORY control in CD changer mode (if equipped) to advance to the next disc.

Seekfunction † In radio mode, press to find the next listenable station down the frequency band. † In radio mode, press

to find the next listenable station up the frequency band.

† In tape mode, use the SEEK function to access the next previous

selection.

† In CD mode (if equipped), use

or

the SEEK function to access the next

46

- VOLUME +

MODE

SEEK

MEMORY

- VOLUME +

MODE

SEEK

MEMORY

- VOLUME +

MODE

SEEK

MEMORY

or previous

selection.

Controls and features

CD changer (if equipped) Your CD changer is located in the center console. Slide the door to access the CD changer magazine.

Press

to eject the magazine.

1. Pull the lever to remove a CD tray from the magazine.

47

Controls and features

2. Insert one disc into each CD tray of the magazine (up to 6 discs). Ensure that the label side is facing up. If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine.

3. Insert each CD tray, with the disc loaded, all the way into the CD magazine.

4. Insert the CD magazine into the changer.

5. Slide the door to the left to close.

Use only compact discs containing this mark.

The magazine does not need to be full for the changer to operate.

48

Controls and features

Radio power must be turned on to play the CDs in the changer. The magazine may be stored in the glove compartment when not being used. The CD magazine may be inserted or ejected with the radio power off. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty. Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD changer as that jamming may occur.

Troubleshooting the CD changer (if equipped)

The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case.

If sound skips: † You may be traveling on a rough road, playing badly scratched discs or

the disc may be dirty. Skipping will not scratch the discs or damage the player.

If your changer does not work, it may be that: † A disc is already loaded where you want to insert a disc. † The disc is inserted with the label surface downward. † The disc is dusty or defective. † A disc with format and dimensions not within industry standards is

inserted.

Cleaning compact discs Inspect all discs for contamination before playing. If necessary, clean discs only with an approved CD cleaner and wipe from the center out to the edge. Do not use circular motion.

CD and CD changer care † Handle discs by their edges only. Never touch the playing surface. † Do not expose discs to direct sunlight or heat sources for extended † Do not insert more than one disc into each slot of the CD changer

periods of time.

magazine.

49

Controls and features

Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order to maintain the best sound and operation.

Cassette and cassette player care † Use only cassettes that are 90 minutes long or less. † Do not expose tapes to direct sunlight, high humidity, extreme heat or

extreme cold. Allow tapes that may have been exposed to extreme temperatures to reach a moderate temperature before playing. † Tighten very loose tapes by inserting a finger or pencil into the hole † Remove loose labels before inserting tapes. † Do not leave tapes in the cassette player for a long time when not

and turning the hub.

being played.

Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all frequencies are used in a given area. Radioreceptionfactors Three factors can affect radio reception: † Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations.

† Terrain. Hills, mountains and tall buildings between your vehicle’s antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms. Moving away from an interfering structure (out of its “shadow”) returns your reception to normal.

50

Controls and features † Station overload. Weak signals are sometimes captured by stronger signals when you pass a broadcast tower. A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed.

The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo.

Audio system warranties and service Refer to the “Warranty Guide” for audio system warranty information. If service is necessary, see your dealer or a qualified technician.

CLIMATE CONTROL SYSTEM

Manual heating and air conditioning system

LO

HI

PANEL

OFF

PANEL & FLOOR

A/C

MAX A/C

FLOOR

FLR & DEF

DEF

COOL

WARM

Fanspeedcontrol Controls the volume of air circulated in the vehicle.

Temperaturecontrolknob Controls the temperature of the airflow inside the vehicle.

Modeselectorcontrol Controls the direction of the airflow to the inside of the vehicle.

LO

HI

COOL

WARM

PANEL

OFF

PANEL & FLOOR

A/C

MAX A/C

FLOOR

FLR & DEF

DEF

51

Controls and features

The air conditioning compressor will operate in all modes except PANEL and FLOOR. However, the air conditioning will only function if the outside temperature is about 10°C (50°F) or higher. Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. † MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster. Airflow will be from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle.

† A/C-Uses outside air to cool the vehicle. It is quieter than MAX A/C

but not as economical. Airflow will be from the instrument panel registers. Air conditioning and heating capabilities are provided in this mode. † PANEL -Distributes outside air through the instrument panel registers.

However, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode. † OFF-Outside air is shut out and the fan will not operate. For short

periods of time only, use this mode to prevent undesirable odors from entering the vehicle.

† PANEL & FLOOR - Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers. † FLOOR -Allows for maximum heating by distributing outside air

through the floor ducts. However, the air will not be cooled below the outside temperature because the air conditioning does not operate in this mode. † FLR & DEF-Distributes outside air through the windshield defroster

ducts and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air

52

Controls and features

† DEF

sent to the windshield defroster ducts. If the temperature is about 10°C (50°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging.

-Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the temperature is about 10°C (50°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging.

To aide in defogging and demisting (removing condensation on the inside of the windshield) in cool weather: 1. Select PANEL & FLOOR 2. Set the temperature control to full heat 3. Select A/C 4. Set the fan speed to HI 5. Direct the outer panel vents towards to side windows To increase airflow to the outer panel vents, close the central panel vents. Operatingtips † In humid weather, select DEF

climate control system in the OFF or MAX A/C position.

before driving. This will reduce fogging on your windshield. After a few minutes, select any desired position. † To reduce humidity buildup inside the vehicle, don’t drive with the † Don’t put objects under the front seat that will interfere with the † Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield under the hood).

airflow to the back seats.

53

Controls and features † If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Then operate your air conditioner as you would normally. † Do not place objects over the defroster outlets. These objects can block airflow and reduce your ability to see through your windshield. Also, avoid placing small objects on top of your instrument panel. These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system.

Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop.

Electronic Automatic Temperature Control (EATC) system (if equipped) The EATC system will maintain a selected temperature and automatically control airflow. You can override automatic operation with any of the override controls, the fan speed control or steering wheel controls (if equipped). TurningtheEATCon Press AUTOMATIC, any of the override controls or the fan speed control. The EATC will only operate when the vehicle is running.

OUTSIDE TEMP

OUTSIDE TEMP

PNL • FLR

PNL • FLR

FLR • DEF

MAX A/C

FLR • DEF

MAX A/C

AUTO

AUTO

FLOOR

FLOOR

VENT

VENT

OFF

AUTOMATIC

DEF

OFF

DEF

AUTOMATIC

HI

LO

HI

LO

54

TurningtheEATCoff Press OFF. The Outside Temperature function will continue to operate until the ignition is turned off.

Controls and features

OFF

AUTOMATIC

FLR • DEF

DEF

HI

LO

Automaticoperation Press AUTOMATIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window. The EATC system will either heat or cool to achieve the selected temperature. The system will automatically determine fan speed, airflow location and if outside air or recirculated air is required. Fan speed remains automatic unless the fan speed thumbwheel is turned or the steering wheel fan speed control is pressed (if equipped). When in AUTOMATIC and weather conditions require heat, air will be sent to the floor. However, if the engine is not warm enough to provide heat, the fan will be at a low speed and the air will be directed to the windshield. In 31⁄2 minutes or less, the fan speed will start to increase and the airflow location will change to the floor area. If unusual conditions exist (i.e.-window fogging, etc.), the manual override controls allow you to select airflow locations and the fan control allows you to adjust fan speed as necessary. Temperatureselection The display window indicates the selected temperature, function (AUTO or one of the override controls) and manual control of fan speed (

) if automatic fan speed is not desired.

˚F AUTO

55

Controls and features

To control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons.

OUTSIDE TEMP

MAX A/C

VENT

PNL • FLR

OUTSIDE TEMP

For continuous maximum cooling, push the blue button until 16°C (60°F) is shown in the display window. The EATC will continue maximum cooling (disregarding the displayed temperature) until a warmer temperature is selected by pressing the red button. For continuous maximum heating, push the red button until 32°C (90°F) is shown in the display window. The EATC will continue maximum heating (disregarding the displayed temperature) until a cooler temperature is selected by pressing the blue button. Temperatureconversion Press MAX A/C and DEF at the same time (for one second) to switch between Fahrenheit and Celsius. The English/Metric (E/M) control on the trip computer and message center (if equipped) will not change temperature display. Fanspeed( When AUTOMATIC is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, use the thumbwheel or steering wheel control to cancel automatic fan speed operation. Rotate the thumbwheel up for higher fan speed or down for lower fan speed. Press the steering wheel control (if equipped) up for higher fan speed or down for lower fan speed.

AUTOMATIC

FLR • DEF

DEF

OFF

AUTOMATIC

LO

PNL • FLR

FLR • DEF

MAX A/C

HI

AUTO

FLOOR

VENT

DEF

OFF

LO

HI

56

Controls and features

The display will show manual fan operation.

to indicate

To return to automatic fan operation, press AUTOMATIC. Manualoverridecontrols The override controls are located at the bottom of the EATC and allow you to determine where airflow is directed. To return to full automatic control, press AUTOMATIC.

OUTSIDE TEMP

PNL • FLR

MAX A/C

AUTO

FLOOR

VENT

˚F AUTO

OFF

AUTOMATIC

FLR • DEF

DEF

HI

LO

The air conditioning compressor can operate in all modes except FLOOR and VENT. It will also operate only when required when AUTOMATIC has been selected. However, the air conditioning will only function if the outside temperature is about 10°C (50°F) or higher. Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. Under normal conditions, your vehicle’s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. † MAX A/C-Uses recirculated air to cool the vehicle. The temperature

will display 16°C (60°F). To exit, press AUTOMATIC or any other override controls. MAX A/C is noisier than normal A/C but more economical and will cool the inside of the vehicle faster. Airflow is from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle. † VENT-Distributes outside air through the instrument panel registers.

However, the air cannot be cooled below the outside temperature because the air conditioning does not operate in this mode.

† PNL†FLR-Distributes outside air through the instrument panel

registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. The air will be heated or cooled based on the temperature selection. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers.

57

Controls and features † FLOOR-Allows for maximum heating by distributing outside air

through the floor ducts. However, the air cannot be cooled below the outside temperature because the air conditioning does not operate this mode.

† FLR†DEF-Distributes outside air through the windshield defroster ducts and the floor ducts. Heating and air conditioning capabilities are provided in this mode. The air will be heated or cooled based on the temperature selection. For added customer comfort, the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defroster ducts. If the temperature is about 10°C (50°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging.

-Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the outside air temperature is about 10°C (50°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging. † OFF-Outside air is shut out and the fan will not operate. For short

periods of time only, use this mode to reduce undesirable odors from entering the vehicle.

† DEF

Displayingoutsidetemperature Press OUTSIDE TEMP to display the outside air temperature. It will be displayed until OUTSIDE TEMP is pressed again.

OUTSIDE TEMP

MAX A/C

VENT

PNL • FLR

If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to the window. If a manual override function is selected while the outside temperature is displayed, the new function will be displayed for four seconds after it is changed, then the outside temperature will return to the window along with the override selection.

58

Controls and features

The outside temperature reading is most accurate when the vehicle is moving. Higher readings may be obtained when the vehicle is not moving. The readings that you get may not agree with temperatures given on the radio due to differences in vehicle and station locations. Operatingtips † In humid weather, select DEF

before driving. This will reduce fogging on your windshield. After a few minutes, select any desired position. † To reduce humidity buildup inside the vehicle, don’t drive with the † Don’t put objects under the front seat that will interfere with the † Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield).

climate control system in the OFF position.

airflow to the back seats.

† If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Then operate the air conditioner as you would normally.

† When placing objects on top of your instrument panel, be careful to not place them over the defroster outlets. These objects can block airflow and reduce your ability to see through your windshield. Also, avoid placing small objects on top of your instrument panel. These objects can fall down into the defroster outlets and block airflow and possibly damage your climate control system.

Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop.

59

Controls and features

Auxiliary A/C-heater controls (if equipped) The auxiliary A/C-heater feature provides increased capacity to quickly heat or cool the vehicle. Besides the driver’s control panel for the front seat occupants, the second row auxiliary A/C-heater controls allow the rear passengers to control the temperature in the rear of the vehicle through a second control panel above the second row, or in the floor console. Your auxiliary A/C controls may be located in the floor console,

FLO O R

PANEL

W A R M

R E A

O F F

HI

O L

C O

60

or located in the overhead console.

Controls and features

In order for the auxiliary A/C-heater controls to function, the driver’s auxiliary A/C-heater control must be set to REAR.

OFF

REAR

The instrument panel climate controls must be on in order for the auxiliary A/C-heater to operate.

LO

HI

HI

COOL

WARM PANEL

FLOOR

PANEL

OFF

PANEL & FLOOR

A/C

MAX A/C

FLOOR

FLR & DEF

DEF

COOL

WARM

When the auxiliary A/C-heater control is set to FLOOR, airflow only occurs from the third row seat floor vent located in the driver’s side rear quarter trim panel. When the auxiliary A/C-heater control is set to PANEL, airflow occurs from the overhead 2nd and 3rd row vents. Turn the fan speed control knob to the desired speed.

OFF

LO

HI

61

Controls and features

Turn the temperature control to the desired temperature. You can get warm or cool air through either the overhead registers or floor vent by turning the auxiliary mode selector: † Far left for airflow to the overhead registers. † Far right for airflow to the rear floor vent. † Anywhere between PANEL and FLOOR to vary airflow between the outlets.

COOL

WARM

PANEL

FLOOR

POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF, shuts off the engine and all accessories without locking the steering wheel. 4. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 5. START, cranks the engine. Release the key as soon as the engine starts.

62

Controls and features

TURN SIGNAL CONTROL † Push down to activate the left † Push up to activate the right turn

turn signal.

signal.

SPEED CONTROL

To turn speed control on † Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph).

ON

OFF

Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.

Do not shift the gearshift lever into N (Neutral) with the speed control on.

63

Controls and features

To turn speed control off † Press OFF or † Turn off the vehicle ignition.

ON

OFF

Once speed control is switched off, the previously programmed set speed will be erased.

To set a speed † Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).

RES

SET

ACCEL

COAST

If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill. If your vehicle speed is faster than the set speed while driving on a downhill, you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed. If your vehicle slows down more than 16 km/h (10 mph) below your set speed on an uphill, your speed control will disengage. This is normal. Pressing RES/RSM/RESUME will re-engage it.

Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.

64

To set a higher set speed † Press and hold SET/SET ACC/

SET ACCEL. Release the control when the desired vehicle speed is reached or † Press and release SET/SET ACC/

SET ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or

Controls and features

RES

SET

ACCEL

† Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release SET/SET ACC/SET ACCEL.

COAST

You can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed.

To set a lower set speed † Press and hold CST/COAST. Release the control when the desired speed is reached or † Press and release CST/COAST. Each press will decrease the set speed by 1.6 km/h (1 mph) or

† Depress the brake pedal. When the desired vehicle speed is reached, press SET/SET ACC/ SET ACCEL.

RES

SET

ACCEL

COAST

RES

SET

ACCEL

COAST

65

Controls and features

To disengage speed control † Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed.

Pressing OFF will erase the previously programmed set speed.

To return to a previously set speed † Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph).

66

ON

OFF

RES

SET

ACCEL

COAST

Controls and features

TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control.

Never adjust the steering wheel when the vehicle is moving.

HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter.

WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals.

67

Controls and features

Push (tap) the end of the stalk briefly for a single swipe (no wash). Push and hold for three swipes with wash. Push and hold for a longer wash (up to ten seconds).

Rear window wiper/washer controls For rear wiper operation, rotate the rear window wiper and washer control to the desired position. Select: INT 2 — One second interval rear wiper. INT 1 — Ten second interval rear wiper. OFF — Rear wiper and washer off. For rear wash cycle, rotate (and hold as desired) the rear wiper/washer control to either From either position, the control will automatically return to the INT2 or OFF position.

position.

Speed dependent wipers When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle’s speed changes.

OVERDRIVE CONTROL

Activating overdrive

(Overdrive) is the normal drive position for the best fuel economy.

The overdrive function allows automatic upshifts and downshifts through all available gears.

68

Controls and features

OVERDRIVE

Deactivating overdrive Press the Transmission Control Switch (TCS) located on the end of the gearshift lever. The Transmission Control Indicator Light (TCIL) (the word OFF) will illuminate on the end of the gearshift lever. The transmission will operate in all gears except overdrive. To return to normal overdrive mode, press the Transmission Control Switch again. The TCIL (the word OFF) will no longer be illuminated. When you shut off and re-start your vehicle, the transmission will automatically return to normal For additional information about the gearshift lever and the transmission control switch operation refer to the Automatic Transmission Operation section of the Driving chapter.

(Overdrive) mode.

OVERDRIVE OFF

OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according to your option package.

Forward storage bin (if equipped) Press the release control to open the storage compartment. The door will open slightly and can be moved to full open. The storage compartment may be used to secure sunglasses or a similar object.

69

Controls and features

Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers:

of actuator control.

† Place Velcroy hook onto back side of aftermarket transmitter opposite † Place transmitter into storage compartment, control down. † Place the provided height adaptors onto the back of the storage bin † Press the storage compartment door to activate the transmitter. One-touch moon roof (if equipped) With trip computer

door as needed.

VENT

ROOF

VENT

70

Without trip computer

Controls and features

AUTO

ROOF

to close.

† Press and release the rear portion of the moon roof control to open. † Press and hold (as desired) the front portion of the moon roof control † To halt motion at any point during one-touch opening, press the † The moon roof has a sliding shade that can be manually opened or † To close the shade, pull it toward the front of the vehicle.

closed when the glass panel is shut.

control a second time.

Do not let children play with the moon roof. They may seriously hurt themselves.

Trip computer For information on the trip computer, refer to Trip computer in the Instrumentation chapter. Electronic compass (if equipped) The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antennas. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy. Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass calibration adjustment.

71

Controls and features

Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone adjustment. Compasszoneadjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map.

8 9

15

14

13

12

11

10

With trip computer 2. Locate the compass module mounted on the center rear view mirror post. 3. Turn ignition to the ON position. 4. Press and hold the RESET button on top of the compass module until the message display in the trip computer shows the current zone setting. 5. Release the RESET button. 6. Press the RESET button until the correct zone is displayed on the trip computer.

72

Controls and features

Without trip computer 1. Press and hold the SELECT control until VAR appears in the display, then release. The display should show the current zone number. 2. Press the SELECT control until the desired zone number appears. The display will flash and then return to normal operation. The zone is now updated.

AUTO

ROOF

CAL

Compasscalibrationadjustment Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Start the vehicle. With trip computer 2. Press and hold the RESET button on the compass module until CAL indicator is displayed in the trip computer. 3. Release pressure from the RESET button. 4. Slowly drive the vehicle in a circle (less than 5 km/h [3 mph]) until the CAL indicator turns off. This will take three to five circles to complete calibration. 5. The compass is now calibrated.

73

Controls and features

Without trip computer 1. Press and hold the SELECT control until CAL appears in the display (approximately eight seconds) and release. 2. Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles until CAL indicator turns off in about 2–3
complete circles. 3. The compass is now calibrated.

Power quarter rear windows (if equipped) † With out a moon roof

† With a moon roof

74

AUTO

ROOF

CAL

VENT

VENT

MODE

E/M

RESET

VENT

ROOF

VENT

Controls and features

Press the quarter windows. Press the quarter windows.

portion of the VENT control to open the power rear

portion of the VENT control to close the power rear

Interior Lamps Maplamps With trip computer

Without trip computer

VENT

ROOF

VENT

AUTO

ROOF

To turn on the map lamps, press the control next to each lamp.

75

Controls and features

Reardomelamp The dome lamp lights when: † any door is opened. † the instrument panel dimmer

switch is held up until the courtesy lamps come on.

† any of the remote entry controls are pressed and the ignition is OFF.

With the ignition key in the ACC or ON position, the rear dome lamp can be turned ON or OFF by sliding the control.

AUTOMATIC DIMMING REAR VIEW MIRRORS (IF EQUIPPED) Your vehicle is equipped with an inside rear view mirror with an auto-dimming function. The electronic day/night mirror will change from the normal state to the non-glare state when bright lights (glare) reach the inside rear view mirror. When the inside rear view mirror detects bright light from in front of or behind the vehicle, the inside rear view mirror will automatically adjust (darken) to minimize glare. Do not block the sensor on the backside of the inside rear view mirror since this may impair proper system performance. Press the control to turn the mirror OFF or AUTO. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse)(when the mirror is on) to ensure a bright clear view when backing up.

AUTO

OFF

ILLUMINATED VISOR MIRROR (IF EQUIPPED) To turn on the visor mirror lamps, slide the mirror cover open. To turn off the visor mirror lamps, slide the mirror cover closed.

76

Controls and features

POWER WINDOWS Press and hold the rocker switches to open and close windows. † Press the top portion of the

rocker switch to close.

† Press the bottom portion of the

rocker switch to open.

One touch down † Press AUTO completely down and

release quickly. The driver’s window will open fully. Depress again to stop window operation.

One touch down can be deactivated during operation by pushing up on the power window control.

AUTO

AUTO

AUTO

77

Controls and features

Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls.

WINDOW LOCK

Accessory delay With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened.

POWER DOOR LOCKS Press U to unlock all doors and L to lock all doors.

CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. Move lock control up to engage the childproof lock. Move control down to disengage childproof locks.

78

Controls and features

POWER SIDE VIEW MIRRORS The ignition can be in any position to adjust the power side view mirrors. To adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror.

MIRRORS L R

2. Move the control in the direction you wish to tilt the mirror.

MIRRORS L R

3. Return to the center position to lock mirrors in place.

Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.

79

Controls and features

Signal mirrors (if equipped) When the turn signal is activated, the outer portion of the appropriate mirror housing will blink red. This provides an additional warning to other drivers that your vehicle is about to turn.

Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash.

CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: † Utility compartment † Cupholders † Coin holder slots † Compact disc changer (if equipped)

Use only soft cups in the cupholder. Hard objects can injure you in a collision.

80

Controls and features

Rear center console features (if equipped) The rear center console incorporates the following features: † utility compartment † cupholders POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.

LIFTGATE To open the rear window, turn the liftgate handle to the right. To open the liftgate, turn the liftgate handle to the left. † Do not open the liftgate or

DOOR

GLASS

liftgate glass in a garage or other enclosed area with a low ceiling. If the liftgate glass is raised and the liftgate is also opened, both liftgate and glass could be damaged against a low ceiling. † Do not leave the liftgate or liftgate glass open while driving. Doing so could cause serious damage to the liftgate and its components as well as allowing carbon monoxide to enter the vehicle.

81

Controls and features

Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This

will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle.

SECURILOCKY PASSIVE ANTI-THEFT SYSTEM Your vehicle is equipped with a coded-key anti-theft system. Only the correct key will be able to start your vehicle. If your keys are lost or stolen, you must take your vehicle to your dealership for key reprogramming. This system provides an advanced level of vehicle theft protection. Your vehicle’s engine can only be started with the two coded keys provided with your vehicle. Each time you start your vehicle, the coded key is read by the anti-theft system. If the key identification code matches the code stored in the anti-theft system, the vehicle’s engine is allowed to start. If the key identification code does not match the code stored in the system or if a coded key is not detected (vehicle theft situation), the vehicle’s engine will not operate. If there is any anti-theft problem with your vehicle, ensure ALL coded keys for that vehicle are brought to the dealership, to aid in troubleshooting. The SecuriLocky passive anti-theft system is not compatible with aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Large metallic objects, electronic devices on the key chain that can be used to purchase gasoline or similar items, or a second key on the same key ring as the PATS ignition key may cause vehicle starting concern and record DTC’s under certain conditions. If present, you need to keep these objects from touching the PATS ignition key while starting the engine. These objects and devices cannot damage the PATS ignition key, but can cause a momentary concern if they are too close to the key during engine start. If a problem occurs, turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the encoded ignition key is an approved Ford encoded ignition key.

82

Controls and features

Spare coded keys can be purchased from your dealership and programmed to your anti-theft system. Refer to Programming spare SecuriLocky keys for more information. If one or both of your coded keys are lost or stolen and you want to ensure the lost or stolen key will not operate your vehicle, bring your vehicle and all available coded keys to your dealership for reinitialization.

Theft indicator The theft indicator in the instrument cluster will operate as follows: † When the ignition is OFF, the theft indicator will flash briefly every

two seconds to indicate the anti-theft system is protecting your vehicle.

† When the ignition is turned to ON or START, the theft indicator will light for three seconds and then go out. If the theft indicator stays on for an extended period of time or flashes rapidly, have the system serviced by your dealership or a qualified technician.

Programming spare SecuriLockY keys Spare coded keys can be purchased from your dealership and programmed to your anti-theft system (up to a total of eight keys). Your dealership can program your new coded key(s) to your vehicle or you can do it yourself using the following simple procedure. To program a new coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine). If two previously programmed coded keys are not available (one or both of your original keys were lost or stolen), you must bring your vehicle to your dealership to have the spare coded key(s) programmed.

Procedure to program spare SecuriLockY keys to your vehicle New coded keys must have the correct mechanical key cut for your vehicle. Conventional (non-coded) keys cannot be programmed to your vehicle. You will need to have two previously programmed coded keys and the new unprogrammed SecuriLocky key readily accessible for timely implementation of each step in the procedure. Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition and turn the ignition from OFF to ON (maintain ignition in ON for at least one second).

83

Controls and features

2. Turn ignition to OFF and remove the first coded key from the ignition. 3. Within five seconds of turning the ignition to OFF, insert the second previously programmed coded key into the ignition and turn the ignition from OFF to ON (maintain ignition in ON for at least one second but no more than five seconds). 4. Turn the ignition to OFF and remove the second coded key from the ignition. 5. Within 10 seconds of turning the ignition to OFF, insert the new unprogrammed key (new key/valet key) into the ignition and turn the ignition from OFF to ON (maintain ignition in ON for at least one second). This step will program your new key to a coded key. 6. To program additional new unprogrammed key(s), repeat this procedure from step 1. If the programming procedure was successful, the new coded key(s) will start the vehicle’s engine. The theft indicator (located on the instrument panel) will light for three seconds and then go out. If the programming procedure was not successful, the new coded key(s) will not operate the vehicle’s engine. The theft indicator will flash on and off. Wait at least one minute and then repeat the procedure from step 1. If failure repeats, bring your vehicle to your dealership to have the new spare key(s) programmed.

REMOTE ENTRY SYSTEM Your vehicle is equipped with a remote entry system which allows you to: † unlock the vehicle doors without a key. † lock all the vehicle doors without a key. † activate the personal alarm. The remote entry features only operate with the ignition in the OFF position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting.

84

Controls and features

Unlocking the doors Press this control to unlock the driver door. The interior lamps and running board lamps (if equipped) will illuminate. The memory mirrors/seat (if equipped) will also be moved to position 1, 2 or 3 depending upon which remote entry transmitter (1, 2 or 3) is used. Press the control a second time within three seconds to unlock all doors.

Locking the doors Press this control to lock all doors. To confirm doors are closed and locked, press this control a second time within three seconds. The door(s) will lock again, the horn will chirp once and the lamps will flash. If any of the doors are open or ajar, the horn will make two quick chirps, reminding you to properly close the doors.

Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

85

Controls and features

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Replacing the battery The remote transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle. A decrease in operating range can be caused by: † weather conditions † nearby radio towers † structures around the vehicle † other vehicles parked next to the vehicle To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the transmitter unit. 3. Snap the two halves back together. Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.

86

Controls and features

Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: † Take all your vehicle’s

transmitters to your dealer for programming, or

† Perform the programming

procedure yourself

Programmingremotetransmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: † Insert a key in the ignition and turn from 3 (OFF) to 4 (ON) eight times in rapid succession (within 10 seconds) with the eighth turn ending in the 4 (ON) position. The doors will lock/unlock to confirm that programming mode has been entered. † Within 20 seconds, program a remote transmitter by pressing any button on a transmitter. The doors will lock/unlock to confirm that the remote transmitter has been programmed. (If more than 20
seconds pass before pressing a remote transmitter button, the programming mode will exit and the procedure will have to be repeated.)

† Repeat the previous step to program additional remote transmitters.

The doors will lock/unlock to confirm that each remote transmitter has been programmed. † When you have completed programming the remote transmitters, turn

the ignition to 3 (OFF) or wait 20 seconds. Again the doors will lock/unlock to confirm programming has been completed.

87

Controls and features

Illuminated entry The illuminated entry system will turn on the interior lights when the remote transmitter unlock control is pressed. The illuminated entry system will turn off the interior lights if the ignition switch is turned to the ON position, or if the remote transmitter lock control is pressed, or after 25 seconds of illumination. The inside lights will not turn off if: † they have been turned on with the dimmer control or † any door is open. The battery save feature will turn off the interior lights 45 minutes after the last door is closed, even if the dimmer control is on.

Memory seat/mirrors/adjustable pedal feature (if equipped) The memory feature allows automatic positioning of the driver seat, side mirrors and adjustable pedals to three programmable positions. † To program position one, move the driver seat, both side mirrors, and adjustable pedals to the desired positions. Press the SET control. The SET control indicator light will briefly illuminate. While the light is illuminated, press control 1.

† To program position two, repeat the previous procedure using control † To program position three, repeat the previous procedure but press

2.

controls 1 and 2 simultaneously.

The memory feature also allows you to recall previously stored positions with your remote transmitter(s). Up to three remote transmitters can be activated to utilize the memory recall positions. Press the memory feature control to move to the previously stored seat/mirror/adjustable pedal positions. Activating/deactivatingthememoryfeatureonyourremote transmitter The memory feature from the remote transmitter can be turned off/on, however, the memory control buttons will continue to operate. Before following the procedure, make sure that the ignition is OFF and all doors and the liftgate window are closed. You must complete steps 1–7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds.

88

Controls and features

1. Turn the ignition key to ON. 2. Press the power door unlock control three times. 3. Turn the ignition key from ON to OFF. 4. Press the power door unlock control three times. 5. Turn the ignition back to ON. The horn will chirp. 6. Press the power door unlock control two times, then press the power lock control once. The horn will chirp twice if the memory feature was deactivated or three times (two short and one long) if the memory feature was activated. 7. Turn ignition to OFF. The horn will chirp once to confirm the procedure is complete.

Autolock (if equipped) This feature automatically locks all doors when: † all vehicle doors, liftgate and liftgate window are closed † the ignition is in the ON position † you shift into or through R (Reverse) † the brake pedal is released Relock The autolock feature repeats when: † any door is opened and closed † the ignition switch is in the ON position, and † the brake pedal is released Deactivating/activatingtheautolockfeature Before following the procedure, make sure that the ignition is OFF and all vehicle doors and the liftgate window are closed. You must complete steps 1-7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. 1. Turn the ignition key to ON. 2. Press the power door unlock control three times. 3. Turn the ignition key from ON to OFF. 4. Press the power door unlock control three times.

89

Controls and features

5. Turn the ignition back to ON. The horn will chirp. 6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. Turn the ignition to OFF. The horn will chirp once to confirm the procedure is complete.

Keyless entry system With the keyless entry keypad, you can: † lock or unlock the vehicle doors without using the key. Your vehicle has a factory set 5 digit code that operates the keyless entry system. You can also program your own 5 digit personal entry code. The factory-set code is located: † on the owner’s wallet card in the glove compartment † taped to the computer module. When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation. Programmingyourownpersonalentrycode To program your own code: 1. Enter factory set code (keypad will illuminate when pressed). 2. Press 1/2 control within five seconds of step 1. 3. Enter your personal 5 digit code. Enter each digit within five seconds of previous one. Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes. Your personal code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase it in favor of the new code. If you wish to erase your personal code, use the following instructions: 1. Enter factory set code.

9 0

3 4

5 6

7 8

1 2

90

Controls and features

1 2

3 4

5 6

7 8

9 0

2. Press 1/2 control within five seconds of step one. 3. Press 7/8 control and 9/0 control at the same time within five seconds of step 2. The system will now only respond to the factory set code.

Unlocking the doors with the keyless entry system To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will also illuminate. To unlock all doors, enter the factory set code or personal code (driver door unlocks) and press the 3/4 control within five seconds. Lockingthedoorswiththekeylessentrysystem It is not necessary to enter the factory or personal code prior to locking all doors. To lock the doors: † Press the 7/8 control and the 9/0 control at the same time. Activating/deactivatingautolockwiththekeylessentrysystem Before following the activation or deactivation procedures, make sure that the anti-theft system (if equipped) is not armed, ignition is off, and all vehicle doors and liftgate window are closed. 1. Enter 5 digit entry code 2. Press and hold 7/8 control 3. Press and release 3/4 control while holding 7/8 control 4. Release 7/8 control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. To re-activate autolock, repeat steps 1–4.

91

Seating and safety restraints

SEATING

Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints. The head restraints can be moved up and down.

Using the manual lumbar support Turn the lumbar support control toward the front of vehicle to move the lumbar support forward for more direct support. Turn the lumbar support control toward the rear of vehicle to move the lumbar support back for less direct support.

Adjusting the front manual seat

Never adjust the driver’s seat or seatback when the vehicle is moving.

Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop.

92

Before driving

Introduction

Instrumentation

Controls and features

Seating and safety restraints

Starting and driving

Starting

Driving

Roadside emergencies

Servicing

Maintenance and care

Capacities and specifications

Customer assistance

Reporting safety defects

Index

Contents

19

92

129

134

159

181

226

235

247

248

All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation. Copyright © 1999 Ford Motor Company

Introduction

The following warning may be required by California law: CALIFORNIA Proposition 65 Warning

Engine exhaust, some if its constituents, and certain vehicle components contain or emit chemicals known to the State of

California to cause cancer, or birth defects or other reproductive harm.

ICONS Indicates a safety alert. Read the following section on Warnings.

Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. Indicates a message regarding child safety restraints. Refer to Seating and safety restraints for more information.

Indicates that this Owner Guide contains information on this subject. Please refer to the Index to locate the appropriate section which will provide you more information.

WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment.

Introduction

BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently. This is necessary to give the moving parts a chance to break in.

INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation.

SPECIAL NOTICES

Using your vehicle as a snowplow

Do not use this vehicle for snowplowing.

Using your vehicle as an ambulance

Do not use this vehicle as an ambulance.

Your vehicle is not equipped with the Ford Ambulance Preparation Package.

Notice to owners of pickup trucks and utility type vehicles

Utility vehicles have a significantly higher rollover rate than other types of vehicles.

Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or an accident. Be sure to read Driving off road in the Driving chapter as well as the “Four Wheeling” supplement included with 4WD and utility type vehicles.

Introduction

These are some of the symbols you may see on your vehicle.

Vehicle Symbol Glossary

Safety Alert

See Owner’s Guide

Fasten Safety Belt

Air Bag-Front

Air Bag-Side

Child Seat

Child Seat Installation Warning

Child Seat Tether Anchorage

Brake System

Anti-Lock Brake System

Brake Fluid - Non-Petroleum Based

Traction Control

Master Lighting Switch

Hazard Warning Flasher

Fog Lamps-Front

Fuse Compartment

Fuel Pump Reset

Windshield Wash/Wipe

Rear Window Defrost/Demist

Power Window Lockout

Windshield Defrost/Demist

Power Windows Front/Rear

Introduction

Vehicle Symbol Glossary

Child Safety Door Lock/Unlock

Interior Luggage Compartment Release Symbol

Panic Alarm

Engine Oil

Engine Coolant

Engine Coolant Temperature

Do Not Open When Hot

Battery

Avoid Smoking, Flames, or Sparks

Battery Acid

Explosive Gas

Fan Warning

Power Steering Fluid

Maintain Correct Fluid Level

MAX MIN