2000 Ford Escort Owners Manual

To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wiper arm and press it into place until a click is heard.

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: † Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set.

149

Maintenance and care

Tire Quality Grades apply to new pneumatic tires for use on passenger cars. They do not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it.

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.

Traction AA A B C The traction grades, from highest to lowest are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include

acceleration, cornering, hydroplaning or peak traction characteristics.

Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

150

Maintenance and care

The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed,

underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

SERVICING YOUR TIRES

Checking the tire pressure † Use an accurate tire pressure gauge. † Check the tire pressure when tires are cold, after the vehicle has been

parked for at least one hour or has been driven less than 5 km (3
miles). † Adjust tire pressure to recommended specifications found on the

Certification Label.

Improperly inflated tires can affect vehicle handling and can fail suddenly, possibly resulting in loss of vehicle control.

Tire rotation Because your vehicle’s tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the Scheduled Maintenance Guide. If you notice that the tires wear unevenly, have them checked. † Four tire rotation

151

Maintenance and care

Replacing the tires Replace the tires when the wear band is visible through the tire treads.

When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the

Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the label. If you do not follow these precautions, your vehicle may not drive properly and safely.

Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.),

as originally offered by Ford.

Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose

control and roll over.

Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer.

SNOW TIRES AND CHAINS

Snow tires must be the same size and grade as the tires you currently have on your vehicle.

The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains. If you need to use snow tires and chains, it is

152

Maintenance and care

wheels.

recommended that steel wheels are used of the same size and specifications as those originally installed. Follow these guidelines when using snow tires and chains: † Do not use tire chains on aluminum wheels. Chains may chip the † Use only SAE Class S chains. † Install chains securely, verifying that the chains do not touch any † Drive cautiously. If you hear the chains rub or bang against your

wiring, brake lines or fuel lines.

vehicle, stop and re-tighten the chains. If this does not work, remove the chains to prevent damage to your vehicle.

† If possible, avoid fully loading your vehicle. † Do not use tire chains with 38 cm (15 inch) wheel/tire options. Using

chains on this size tire may cause damage to steering, suspension and/or body components.

tire chains on dry roads.

† Remove the tire chains when they are no longer needed. Do not use † The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains.

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS

Important safety precautions

Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.

The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops

before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others.

153

Maintenance and care

If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel system to work improperly in a collision, which may result in possible personal injury.

Automotive fuels can cause serious injury or death if misused or mishandled.

Gasoline may contain benzene, which is a cancer-causing agent.

Observe the following guidelines when handling automotive fuel: † Extinguish all smoking materials

and any open flames before fueling your vehicle.

fueling.

† Always turn off the vehicle before † Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours. † Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind

can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury.

† Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury.

† Fuels can also be harmful if absorbed through the skin. If fuel is

splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation.

154

Maintenance and care † Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result. If fuel is splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction.

When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while

refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes.

The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an

ungrounded fuel container.

Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: † Place approved fuel container on the ground. † DO NOT fill a fuel container while it is in the vehicle. † Keep the fuel pump nozzle in contact with the fuel container while † DO NOT use a device that would hold the fuel pump handle in the fill

filling.

position.

Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1/8 turn on/off feature. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on the filler pipe. 5. Turn the filler cap clockwise 1/8 of a turn until it stops.

155

Maintenance and care

If the “Service Engine Soon/Check Engine” indicator comes on and stays on when you start the engine, the fuel filler cap may not be properly installed. Turn off the engine, remove the fuel filler cap, align the cap properly and reinstall it. If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used.

The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops

before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others.

If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel system to work improperly in a collision, which may result in possible personal injury.

Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. Do not use fuel containing methanol. It can damage critical fuel system components. Your vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based compounds containing MMT. Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty.

Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with an (R+M)/2 octane rating of 87. We do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are using fuel

87(R+M)/2 METHOD

156

Maintenance and care

with the recommended octane rating, see your dealer or a qualified service technician to prevent any engine damage.

Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular” unleaded gasoline. “Premium” unleaded gasoline is not recommended (particularly in the United States) because it may cause these problems to become more pronounced. If the problems persist, see your dealer or a qualified service technician. It should not be necessary to add any aftermarket products to your fuel tank if you continue to use high quality fuel of the recommended octane rating. Aftermarket products could cause damage to the fuel system. Repairs to correct the effects of using an aftermarket product in your fuel may not be covered by your warranty. Many of the world’s automakers issued the World-wide Fuel Charter that recommends gasoline specifications to provide improved performance and emission control system protection for your vehicle. Gasolines that meet the World-wide Fuel Charter should be used when available. Ask your fuel supplier about gasolines that meet the World-wide Fuel Charter.

Cleaner air Ford approves the use of reformulated “cleaner-burning” gasolines to improve air quality. These gasolines may contain oxygenates up to 10% ethanol or 15% MTBE.

Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: † You may need to cycle the ignition from OFF to ON several times after

refueling, to allow the fuel system to pump the fuel from the tank to the engine.

† Your “Service Engine Soon” indicator may come on. For more information on the “Service Engine Soon” indicator, refer to the Instrumentation chapter.

157

Maintenance and care

Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician. Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used.

ESSENTIALS OF GOOD FUEL ECONOMY

Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1 600 km (1 000
miles) of driving (engine break-in period). You will get a more accurate measurement after 3 000 km–5 000 km (2 000 miles-3 000 miles).

Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill Capacities section of the Capacities and specifications chapter. The advertised capacity is the amount of the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty. Empty reserve is the small amount of usable fuel remaining in the fuel tank after the fuel gauge indicates empty. The amount of empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty, you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank. For consistent results when filling the fuel tank: † Use the same filling rate setting (low — medium — high) each time † Allow three automatic click-offs when filling. † Always use fuel with the recommended octane rating.

the tank is filled.

158

Maintenance and care

† Use a known quality gasoline, preferably a national brand. † Use the same side of the same pump and have the vehicle facing the † Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent.

same direction each time you fill up.

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5. Follow one of the simple calculations in order to determine fuel economy: Multiply liters used by 100, then divide by total kilometers traveled. Divide total miles traveled by total gallons used. Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’s fuel economy under current driving conditions. Additionally, keeping records during summer and winter will show how temperature impacts fuel economy. In general, lower temperatures give lower fuel economy.

Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy. Habits † Smooth, moderate operation can yield up to 10% savings in fuel. † Steady speeds without stopping will usually give the best fuel † Idling for long periods of time (greater than one minute) may waste

economy.

fuel.

159

Maintenance and care † Anticipate stopping; slowing down may eliminate the need to stop. † Sudden or hard accelerations may reduce fuel economy. † Slow down gradually. † Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15% † Revving the engine before turning it off may reduce fuel economy. † Using the air conditioner or defroster may reduce fuel economy. † You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy.

less fuel than traveling at 105 km/h [65 mph]).

reduce fuel economy.

† Warming up a vehicle on cold mornings is not required and may † Resting your foot on the brake pedal while driving may reduce fuel † Combine errands and minimize stop-and-go driving. Maintenance † Keep tires properly inflated and use only recommended size. † Operating a vehicle with the wheels out of alignment will reduce fuel † Use recommended engine oil. Refer to Lubricant Specifications. † Perform all regularly scheduled maintenance items. Follow the

economy.

economy.

recommended maintenance schedule and owner maintenance checks found in your vehicle Scheduled Maintenance Guide.

at any speed.

Conditions † Heavily loading a vehicle or towing a trailer may reduce fuel economy † Carrying unnecessary weight may reduce fuel economy (approximately † Adding certain accessories to your vehicle (for example bug

0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried).

deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy.

† Using fuel blended with alcohol may lower fuel economy.

160

driving on hilly terrain.

12–16 km (8–10 miles) of driving.

cruise gear and with steady pressure on the gas pedal.

Maintenance and care † Fuel economy may decrease with lower temperatures during the first † Driving on flat terrain offers improved fuel economy as compared to † Transmissions give their best fuel economy when operated in the top † Close windows for high speed driving. EPA window sticker Every new vehicle should have the EPA window sticker. Contact your dealer if the window sticker is not supplied with your vehicle. The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles. It is important to note the box in the lower left corner of the window sticker. These numbers represent the Range of L/100 km (MPG) expected on the vehicle under optimum conditions. Your fuel economy may vary depending upon the method of operation and conditions.

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: † Use only the specified fuel listed. † Avoid running out of fuel. † Do not turn off the ignition while your vehicle is moving, especially at † Have the items listed in your Scheduled Maintenance Guide performed

high speeds.

according to the specified schedule.

The scheduled maintenance items listed in the Scheduled Maintenance Guide are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.

161

Maintenance and care

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine

compartment and exhaust system, which can start a fire.

Illumination of the “Service Engine Soon” light, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power, could indicate that the emission control system is not working properly.

Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment.

Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine. This decal identifies engine displacement and gives some tune up specifications. Please consult your “Warranty Guide” for complete emission warranty information.

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If your “Check Engine/Service Engine Soon” light is on, refer to the description in the Warning Lights and Chimes section of the Instrumentation chapter. Your vehicle may not pass the I/M test with the “Check Engine/Service Engine Soon” light on. If the vehicle’s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition. To ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: † First, at least 10 minutes of driving on an expressway or highway. † Next, at least 20 minutes driving in stop-and-go, city-type traffic with

at least four idle periods.

Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The

162

Maintenance and care

engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete.

BULBS

Replacing exterior bulbs It is a good idea to check the operation of the following lights frequently: † Headlamps † Turn signals † Foglamps (if equipped) † High-mount brakelamp † Tail lamps † Brakelamps † Backup lamps † License plate lamp † Hazard flashers Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance.

Replacing headlamp bulbs 1. Make sure that the headlamps are turned OFF. 2. Open the hood and disconnect the headlamp wiring socket from the in-line connector. This will make it easier to change the bulb. 3. Remove the protective dust shield from the housing by turning the dust shield counterclockwise (when viewed from the rear).

4. Disconnect the electrical connector from the bulb by pulling rearward.

163

Maintenance and care

5. Remove the bulb retaining ring by rotating it counterclockwise.

6. Without turning, remove the old bulb from the lamp assembly by pulling it straight back out of the lamp assembly and replace.

Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

7. Install the new bulb in lamp assembly by pushing straight in with the bulb’s plastic base facing upward. Turn the bulb slightly to align the grooves in the plastic base with the tabs in the lamp assembly. 8. Install the bulb retaining ring over the plastic base and lock the ring by rotating it clockwise until it snaps into place. 9. Connect the electrical connector into the plastic base until it “snaps.” 10. Install the protective dust shield and lock the shield by rotating it clockwise until it locks into position. 11. Connect the headlamp wiring socket to the in-line connector. 12. Turn the headlamps on and make sure they work properly. If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again.

164

Maintenance and care

Replacingfoglampbulbs 1. Remove the bulb socket from the foglamp by turning counterclockwise. 2. Disconnect the electrical connector from the foglamp bulb. 3. Connect the electrical connector to the new foglamp bulb. 4. Install the bulb socket in the foglamp turning clockwise.

Replacinghigh-mountbrakelampbulbs To remove the brakelamp bulb: 1. Push the center of the push pins in to release tension. 2. Pull the push pins out of the cover and slide the cover away from the package tray. 3. Remove the bulb by rotating it counterclockwise and pulling it out of the lamp assembly. 4. Carefully pull out the bulb straight out of the socket and push in new bulb. To install the brakelamp bulb: 1. Install the bulb into the lamp assembly and rotate clockwise. 2. Install the push pins in the cover far enough that the pins protrude outside of the cover about 6 mm (1/4 inch). 3. Install the cover and secure with the push pins.

165

Maintenance and care

Taillamp/turnsignal/backuplampbulbs The tail/turn signal lamp and backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb. 1. Open trunk to expose the tail lamp assembly. Remove the two screws from the front of the lamp. 2. The tail lamp has hidden fasteners which can be disengaged by hitting the lamp, with the side of your hand, toward the side of the vehicle. 3. Pull lamp assembly away from vehicle for access to bulbs. 4. Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly. 5. Pull the bulb from the socket and push in the new bulb. 6. Install the bulb socket into the lamp by rotating it clockwise. 7. Position the tail lamp on the vehicle and gently tap the lens to engage the clips. Install the screws.

166

Maintenance and care

Licenseplatelamps To change the license plate bulbs: 1. Remove two screws and the license plate lamp assembly from the rear bumper. 2. Carefully pull the bulb out from the lamp assembly and push in the new bulb. 3. Install the lamp assembly on rear bumper with two screws.

Replacingbackuplampbulbs For bulb replacement, see a dealer or qualified technician.

INTERIOR BULBS Domelamp 1. Remove the lamp lens by applying pressure to both tabs at the top of the lamp and pulling lens downward. 2. Pull out the burned-out bulb and install a new one. 3. Install the lamp lens by applying pressure to both sides of the lamp lens and popping the lamp lens up on the assembly.

OFF DOOR ON

Maplamps For bulb replacement, see a qualified service technician or your dealer.

167

Maintenance and care

Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time. Function Front park/turn lamps Foglamps (if equipped) Headlamps-aero high and low beam Rear license plate lamps High-mount brake lamp Backup lamps Brake lamps Interior overhead lamp All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer

Trade Number 3457 NAK (amber) 881
9007
168
921
3156K 3157K 12V/10W

AIMING THE HEADLAMPS Your vehicle is equipped with a Vehicle Headlamp Aim Device (VHAD) on each headlamp. Each headlamp may be properly aimed in the vertical (up/down) and the horizontal (left/right) directions using your VHAD system. The headlamps on your vehicle are properly aimed at the assembly plant. A bubble (vertical indicator) that is not centered between the two red lines does not necessarily indicate out-of-aim headlamps. If your vehicle is not positioned on a level surface, the slope will be included in the vertical indication. Therefore, vertical and horizontal headlamp adjustment should be performed only when the beam direction appears to be incorrect. You will need one 4 mm wrench or socket to make the adjustments. If the vehicle has been in an accident, the vehicle’s front structure should be properly aligned before aiming the headlamps.

168

Maintenance and care

Horizontal aim adjustment 1. Park the vehicle on a level surface. 2. With the hood open, locate the horizontal indicator and the adjusting screw. They are located below the viewing window at the rear of the headlamp assembly.

3. The “L” and “R” under the viewing window on the top of the headlamp refer to the directional change (left or right) of the horizontal aim. 4. Use a 4 mm wrench or socket to turn the horizontal adjusting screw until the forward edge of the knurled portion of the screw is aligned with the “0” reference mark (as shown) on the plastic slider when viewed directly from above.

Vertical aim adjustment 1. Park the vehicle on a level surface. 2. With the hood open, locate the bubble level and the vertical adjustment screw. The adjustment screw is located on the outboard side of the headlamp below the headlamp upper attachment.

DN

UP

169

Maintenance and care

3. The “UP” and “DN” on the bubble indicate the directional change (up or down) of the vertical aim. 4. Use a 4 mm wrench or socket to turn the vertical adjusting screw clockwise or counterclockwise until the bubble is centered between the lines.

DN

UP

Repeat the above process to the other headlamp, if necessary.

CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes.

Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results. To avoid spots, avoid washing when the hood is still warm, immediately after or during exposure to strong sunlight. During winter months, it is especially important to wash the vehicle on a regular basis. Large quantities of dirt and road salt are difficult to remove and also cause damage to the vehicle. Any gasoline spilled on the vehicle or deposits such as bird droppings should be washed and sponged off as soon as possible. Deposits not removed promptly can cause damage to the vehicle’s paintwork. Remove any exterior accessories, such as antennas, before entering a car wash. If you have wax applied to the vehicle at a commercial car wash, it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield. After washing, apply the brakes several times to dry them.

170

Maintenance and care

Waxing your vehicle Waxing your vehicle on a regular basis will reduce minor scratches and paint damage. Wax when water stops beading on the surface. This could be every three or four months, depending on operating conditions. Use only carnauba or synthetic-based waxes. Use a cleaning fluid with a clean cloth to remove any bugs before waxing your vehicle. Use tar remover to remove any tar spots. Avoid getting wax on the windshield, or on any surfaces which appear coarse or bumpy. If you have wax applied at a commercial car wash, it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield.

Repairing paint chips Minor scratches or paint damage from road debris may be repaired with the Ultra Touch Prep and Finishing Kit (#F7AZ-19K507–BA), Lacquer Touch-up Paint (#ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (#ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle’s specific coloring. Observe the application instructions on the products. Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately.

Cleaning the wheels Wash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents. Never use abrasives that will damage the finish of special wheel surfaces. Use a tar remover to remove grease and tar. The brushes used in some automatic car washes may damage the finish on your wheels. Before going to a car wash, find out if the brushes are abrasive.

Cleaning non-painted plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners.

171

Maintenance and care

Underbody Flush the complete underside of vehicle frequently. Keep body drain holes unplugged. Inspect for road damage.

Cleaning mirrors Do not clean your mirrors with a dry cloth or abrasive materials. Use a soft cloth and mild detergent and water. Be careful when removing ice from outside mirrors because you may damage the reflective surface.

Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. If necessary, use a tar remover such as Ford Extra Strength Tar and Road Oil Remover (B7A-19520–AA). To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners.

Cleaning the wiper blades, windshield and rear window If the wiper blades do not wipe properly, clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents. If the wiper still does not wipe properly, this could be caused by substances on the windshield or rear window such as tree sap and some hot wax treatments used by commercial car washes. Clean the outside of the windshield or rear window with a non-abrasive cleaner such as Ford Ultra-Clear Spray Glass Cleaner, (E4AZ-19C507–AA), available from your Ford Dealer. Do not use abrasive cleansers on glass as they may cause scratches. The windshield or rear window is clean if beads do not form when you rinse it with water. The windshield, rear window and wiper blades should be cleaned on a regular basis, and blades or rubber elements replaced when worn.

Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: † Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage. † Do not spray with cold water to avoid cracking the engine block or

other engine components.

172

† Never apply anything to the drive belt (including belt dressing).

Maintenance and care

† Cover the highlighted areas to prevent water damage when cleaning † Never wash or rinse the engine while it is running; water in the

the engine.

running engine may cause internal damage.

Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.

Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of

the air bag system.

Cleaningtheinstrumentclusterlens Clean with a damp cloth, then dry with a dry cloth. Do not use household or glass cleaners as these may damage the lens.

Cleaning seats equipped with side air bags Remove dust and loose dirt with a whisk broom or a vacuum cleaner. Remove fresh spots immediately. Follow the directions that come with the cleaner. Do not saturate the seat cover with upholstery cleaner.

173

Maintenance and care

Do not use chemical solvents or strong detergents when cleaning the seat mounted side air bag. Such products could contaminate the side air bag system and affect performance of the side air bag in a collision.

Woodtone trim Wipe stains with a soft cloth and a multi-purpose cleaning solution.

Inside windows Use Ultra-Clear Spray Glass Cleaner (E4AZ-19C507–AA) for the inside windows if they become fogged.

Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, wear or cuts. If your vehicle has been involved in an accident, refer to the Safety belt maintenance section in the Seating and safety restraints chapter.

Cleaning leather seats (if equipped) To clean, simply use a soft cloth dampened with water and a mild soap. Wipe the leather again with a damp cloth to remove soap residue. Dry with a soft cloth. For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label. Regular cleaning of your leather upholstery helps maintain its resiliency and color. Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber, vinyl or plastics.

Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner. Remove fresh spots immediately. Do not use household or glass cleaners. These agents can stain and discolor the fabric. Use a mild soap and water solution if necessary.

174

Capacities and specifications

MOTOCRAFT PART NUMBERS Component

2.0L SOHC I4
engine FA-1643
FG-862
BXT-58
FL-400–S EV-244
AGSF-34EE**

2.0L DOHC Zetec engine FA-1643
FG-862
BXT-58
FL-2005
EV-224
AZFS-32FE**

Air filter element Fuel filter Battery Oil filter PCV valve Spark plugs* * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. ** If a spark plug is removed for inspection, it must be reinstalled in the same cylinder.If a spark plug needs to be replaced, use only spark plugs with the same service part number suffix letter as shown on the engine decal.

REFILL CAPACITIES

Fluid

Brake fluid

Ford Part Name High Performance DOT 3 Motor Vehicle Brake Fluid

Application

Capacity

All

Fill to line on reservoir

Engine coolant1 Premium Engine

Coolant

Engine oil (includes filter change)

Fuel tank capacity

Motorcraft SAE 5W-30 Super Premium Motor Oil N/A

Automatic transaxles Manual transaxles ZX2

Sedan

All

6.0L (6.3 quarts) 5.0L (5.3 quarts) 4.25L (4.5 quarts) 3.8L (4.0 quarts) 48.5L (12.8 gallons)

175

Capacities and specifications

Fluid

Power steering fluid Transmission fluid

Windshield washer fluid

Ford Part Name Motorcraft MERCONt ATF

Motorcraft MERCONt ATF

Ultra-Clear Windshield Washer Concentrate

Application

Capacity

All

Automatic transaxles Manual transaxles All

Fill to line on reservoir 3.9L (4.1 quarts) 3.35L (3.55 quarts) 2.2L (2.32 quarts)

1 Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter.

LUBRICANT SPECIFICATIONS

Ford Part Name or Equivalent High Performance DOT 3 Motor Vehicle Brake Fluid Multi-Purpose Grease

Ford Part Number

Ford Specification

C6AZ-19542-AB ESA-M6C25-A

and DOT 3

DOAZ-19584-AA or F5AZ-19G209-AA

ESB-M1C93-B or ESR-M1C159-A

Penetrating and Lock Lubricant Motorcraft MERCONt ATF

E8AZ-19A501-B none

XT-2-QDX

MERCONt

Item

Brake fluid

Door latch, hood latch, auxiliary hood latch, trunk latch, seat tracks. Lock cylinder

Automatic transaxle

176

Capacities and specifications

Item

Ford Part Name or Equivalent

Manual transaxle Motorcraft

Engine oil

MERCONt ATF Motorcraft SAE 5W-30 Super Premium Motor Oil CV Joint Grease Constant velocity joints (High Temp.) Engine coolant1 Ford Premium Engine Coolant

Power steering fluid Windshield washer fluid

Motorcraft MERCONt ATF Ultra-clear Windshield Washer Concentrate

Ford Part Number

XT-2-QDX

Ford Specification

MERCONt

XO-5W30-QSP WSS-M2C153-G

and API Certification Mark ESP-M1C207-A

ESE-M97B44-A

MERCONt

E43Z-19590-A

E2FZ-19549-AA (in Canada, Motorcraft CXC-8-B) XT-2-QDX

C9AZ-19550-AC ESR-M17P5-A

1 DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544-AA, meeting Ford specification WSS-M97B44-D (orange in color) Refer to Adding engine coolant, in the Maintenance and Care chapter.

ENGINE DATA Engine

Cubic inches Required fuel Firing order Spark plug gap

Ignition system Compression ratio

2.0L SOHC I4
engine 121
87 octane 1-3-4-2
1.3-1.4 mm (0.052-0.056 inch) DIS 9.35:1

2.0L DOHC Zetec engine 121
87 octane 1-3-4-2
1.22-1.32 mm (0.048-0.052 inch) DIS 9.6:1

177

Capacities and specifications

VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear

Coupe mm (in) 4 451.0 (175.2) 1 712.0 (67.4) 1 328.4 (52.3) 2 499.0 (98.4) 1 435.1 (56.5) 1 435.1 (56.5)

Sedan mm (in) 4 432.3 (174.5) 1 681.0 (66.2) 1 351.0 (53.2) 2 499.0 (98.4) 1 435.1 (56.5) 1 435.1 (56.5)

55

† Coupe and Sedan models

178

Capacities and specifications

55

† Coupe model

† Coupe model

179

Capacities and specifications

† Sedan model IDENTIFYING YOUR VEHICLE

Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side.

180

MFD. BY FORD MOTOR CO. IN U.S.A.

DATE: XXXXX FGAWR: XXXXXX/XXXXXXX

GVWR:XXXXX LB/ XXXXX KG RGAWR: XXXXXXX/XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE.

VIN: XXXXXXXXXXXXXXXXX

TYPE: XXXXXXXXXXXXXXX

MAXIMUM LOAD=OCCUPANTS + LUGGAGE=XXXKG/XXXXLB OCCUPANTS: X TOTAL X FR X 2ND X RR OCCUPANTS LUGGAGE XX XXXKG/XXXXLB X XXXKG/XXXXLB

TIRE: XXXX/XXXXX XXX PRESSURE (FR) XXX kPa/33 PSI COLD PRESSURE (RR) XXX kPa/33 PSI COLD TRAILER TOWING - SEE OWNER GUIDE

EXT PNT: XXXXXX XXXXXX RC: XX DSO: XXXX F0000
BAR INT TR TP/PS R AXLE TR SPR T0000
X XX XXX X XX X XXXX

UTC (cid:209) FOHT-15294A10-GA

Capacities and specifications

Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.)

XXXXXXXXXXXXXXXXX

Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block and transmission.

181

Customer assistance

Ford Extended Service Plan You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada). It provides the following: † benefits during the warranty period depending on the plan you

purchase (such as: reimbursement for rentals; coverage for certain maintenance and wear items)

† protection against repair costs after your Bumper to Bumper Warranty

expires

You may purchase Ford ESP from any participating Ford and Lincoln/ Mercury and Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage. (In Hawaii, rules vary. See your dealer for details.) When you buy Ford ESP, you receive Peace-of-Mind protection throughout the United States and Canada, provided by a network of more than 5,000 participating Ford or Lincoln/Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Please contact your dealer for further information. Since this information is subject to change, please ask your dealer for complete details about Ford Extended Service Plan coverage options.

Getting the service you need

At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. When you need warranty repairs your selling dealer would like you to return to it for that service, but you may also take your vehicle to another Ford Motor Company or Ford of Canada dealership authorized for warranty repairs. Certain warranty repairs require special training though, so not all dealers are authorized to perform all warranty repairs. That means that depending on the warranty repair needed, the vehicle may need to be taken to another dealer. If a particular dealership can not assist you, then contact the Customer Assistance Center.

182

Customer assistance

If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership. 3. If the inquiry or concern cannot be resolved at the dealership level, please contact the Ford Customer Assistance Center. Ford Motor Company and Ford of Canada dealerships also carry quality parts and accessories, providing you with equipment reliability.

Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P.O. Box 6248
Dearborn, Michigan 48121
1-800-392-3673 (FORD) (TDD for the hearing impaired: 1-800-232-5952) In Canada: Customer Assistance Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
1-800-565-3673 (FORD)

183

Customer assistance

If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P.O. Box 6248
Dearborn, Michigan 48121
1-800-521-4140
(TDD for the hearing impaired: 1-800-232-5952) In Canada: Customer Assistance Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
1-800-565-3673 (FORD) In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Assistance Center: † Your telephone number (home and business) † The name of the dealer and the city where the dealership is located † The year and make of your vehicle † The date of vehicle purchase † The current odometer reading † The vehicle identification number (VIN) If you still have a complaint involving a warranty dispute, you may wish to contact the Dispute Settlement Board (U.S.) or the Mediation/Arbitration Program (Canada). In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This

184

Customer assistance

dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws. THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: † an independent, third-party arbitration program for warranty disputes † available free to owners and lessees of qualifying Ford Motor Company

vehicles

The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law. What kinds of cases does the Board review? Unresolved warranty repair concerns or vehicle performance as designed concerns on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any applicable written new vehicle warranty are eligible for review, except those involving: † a non-Ford product † a non-Ford dealership † sales disputes between customer and dealer except those associated with warranty repairs or concerns with the vehicle’s performance as designed

maintenance and wear items)

service or product concern is being reviewed

† a request for reimbursement of consequential expenses unless a † items not covered by the New Vehicle Limited Warranty (including † alleged personal injury/property damage claims † cases currently in litigation † vehicles not used primarily for family, personal or household purposes (except in states where the Dispute Settlement Board is required to review commercial vehicles)

† vehicles with non-U.S. warranties Concerns are ineligible for review if the New Vehicle Limited Warranty has expired at receipt of your application and, in certain states eligibility is dependent upon the customer’s possession of the vehicle.

185

Customer assistance

Eligibility may differ according to state law. For example, see the unique brochures for California, West Virginia, Georgia and Wisconsin purchasers/lessees.

Board membership The Board consists of: † three consumer representatives † a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. WhattheBoardneeds To have your case reviewed you must complete the application in the DSB brochure and mail it to the address provided on the application form. Some states will require you to use certified mail, with return receipt requested. Your application is reviewed and, if it is determined to be eligible, you will receive an acknowledgment indicating: † the file number assigned to your application † the toll-free phone number of the DSB’s independent administrator Your dealership and a Ford Motor Company representative will then be asked to submit statements. To properly review your case, the Board needs the following information: † legible copies of all documents and maintenance or repair orders † the year, make, model, and Vehicle Identification Number (VIN) listed † the date of repair(s) and mileage at the time of occurrence(s) † the current mileage † the name of the dealer(s) who sold or serviced the vehicle † a brief description of your unresolved concern † a brief summary of the action taken by the dealer(s) and Ford Motor

on your vehicle ownership license

relevant to the case

Company

186

Customer assistance

dealership(s)

† the names (if known) of all the people you contacted at the † a description of the action you expect to resolve your concern You will receive a letter of explanation if your application does not qualify for Board review. Oralpresentations If you would like to make an oral presentation, indicate YES to question #6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. Oral presentation may be requested by the Board as well. Makingadecision Board members review all available information related to each complaint, including oral presentations, and arrive at a fair and impartial decision. Board review may be terminated at any time by either party. Every effort is made to decide the case within 40 days of the date that all requested information is received by the Board. Since the Board generally meets once a month, it may take longer for the Board to consider some cases. After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.

To Request a DSB Brochure/Application For a brochure/application, speak to your dealer or write/call to the Board at the following address/phone number: Dispute Settlement Board P.O. Box 5120
Southfield, MI 48086–5120
1–800–428–3718

187

Customer assistance

You may also contact the North American Customer Assistance Center at 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 or by writing to the Center at the following address: Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P.O. Box 6248
Dearborn, Michigan 48121

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings. In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final; the arbitrator’s award is binding both to you and Ford of Canada. CAMVAP services are available in all territories and provinces, except Quebec. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685.

GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact a district or owner relations/customer assistance office.

188

Customer assistance

The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. In the United States, using leaded fuel may also result in difficulty importing your vehicle back into the U.S. If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A. Telephone: (313) 594-4857
FAX: (313) 390-0804
If you are in another foreign country, contact the nearest Ford dealership. If the dealership employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S. or Canada, register your vehicle identification number (VIN) and new address with Ford Motor Company Worldwide Direct Market Operations.

FORD CAR CARE PRODUCTS FOR YOUR VEHICLE Ford has many quality products available from your dealer to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials and that meet or exceed Ford’s rigid specifications. For best results, use the following or products of equivalent quality: Ford Custom Clearcoat Polish* Ford Custom Silicone Gloss Polish Ford Custom Vinyl Protectant* (not available in Canada) Motorcraft Vinyl Conditioner (Canada only)

189

Customer assistance

Ford Deluxe Leather and Vinyl Cleaner (not available in Canada) Motorcraft Vinyl Cleaner (Canada only) Ford Extra Strength Tar and Road Oil Remover* (not available in Canada) Ford Extra Strength Upholstery Cleaner (Canada only) Ford Extra Strength Upholstery Cleaner (not available in Canada) Ford Metal Surface Cleaner Ford Multi-Purpose Cleaner* Motorcraft Car Wash Concentrate Motorcraft Carlite Glass Cleaner Ford Spot and Stain Remover* Ford Super Premium Tire and Trim Dressing Ford Triple Clean Ford Ultra-Clear Spray Glass Cleaner (not available in Canada) * May be sold with the Motorcraft name FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford accessories are available for your vehicle through your local authorized Ford, Lincoln Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle. In addition, each accessory is made from high quality materials and meets or exceeds Ford’s rigid engineering and safety specifications. Ford accessories are warranted for up to 12 months or 20 000 km (12 000 miles) on all cars and light trucks and 12 months with unlimited distance on medium/heavy duty trucks unless the accessory is installed on a new vehicle, then the warranty becomes the balance of the new vehicle’s warranty or the accessories warranty, whichever is greater. See your dealer for complete warranty information and availability. Not all accessories are available for all models.

Vehicle Security Styled wheel protector locks Vehicle security systems

190

Customer assistance

Comfort and convenience Air conditioner Cargo nets Cargo organizers Engine block heaters

Travel equipment Auto headlamps with daytime running lights (DRL) Console armrest Daytime running lights (DRL) Electrochromic inside mirror with compass Electrochromic inside mirror with compass and temperature display Heavy-duty battery Removable luggage rack Removable luggage rack adapters Soft luggage cover Speed control

Protection and appearance equipment Air bag anti-theft locks Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front end covers (full) Lubricants and oils Molded splash guards Molded vinyl floor mats Rear decklid spoilers Touch-up paint Universal floor mats For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle:

191

Customer assistance † When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety compliance certification label). Consult your dealer for specific weight information. † The Federal Communications Commission (FCC) and Canadian Radio Telecommunications Commission (CRTC) regulate the use of mobile communications systems - such as two-way radios, telephones and theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician.

† Mobile communications systems may harm the operation of your

vehicle, particularly if they are not properly designed for automotive use or are not properly installed. When operated, such systems may cause the engine to stumble or stall. In addition, such systems may be damaged or their performance may be affected by operating your vehicle. (Citizens band [CB] transceivers, garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect your vehicle’s operation.) † Ford cannot assume responsibility for any adverse effects or damage

that may result from the use of such equipment.

ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio: Make checks payable to: HELM, INCORPORATED P.O. Box 07150
Detroit, Michigan 48207
For a free publication catalog, order toll free: 1-800-782-4356
Monday-Friday 8:00 a.m. - 6:00 p.m. EST, for credit card holders only

Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3.

192

Reporting safety defects

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company.

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C. area) or write to: NHTSA U.S. Department of Transportation 400 Seventh Street Washington D.C. 20590
You can also obtain other information about motor vehicle safety from the Hotline.

193

Index

Air bag supplemental restraint system ..........................72
and child safety seats ..............74
description ................................72
disposal ......................................76
driver air bag ............................74
indicator light ......................10,76
operation ...................................74
passenger air bag .....................74
Air cleaner filter ................148,175
Air conditioning ..........................36
Antifreeze (see Engine coolant) ................137
Anti-lock brake system (see Brakes) ...........................89,90
Anti-theft system ...................57,58
arming the system ....................58
disarming a triggered system ...............58,59
disarming an untriggered system ...................58
warning light .............................11
Audio system (see Radio) .........18
Automatic transaxle ...................92
driving with ...............................94
fluid, adding ............................143
fluid, checking ........................143
fluid, refill capacities ..............175
fluid, specification ..................177

Axle

lubricant specifications ..........176
Battery .......................................146
acid, treating emergencies .....146
charging system warning light ................11
jumping a disabled battery ....119
maintenance-free ....................146
replacement, specifications ...175
servicing ..................................146
Belt minder .................................68
Brakes ..........................................89
anti-lock ................................89,90

194

anti-lock brake system (ABS) warning light ........................11,90
brake warning light ..................10
fluid, checking and adding ....135
fluid, refill capacities ..............175
fluid, specifications ..........176,177
lubricant specifications ...176,177
parking ......................................90
shift interlock ............................92
Break-in period .............................3
Capacities for refilling fluids ....175
Certification Label ....................180
Child safety restraints ................77
child safety belts ......................77
Child safety seats ........................78
attaching with tether straps ....82
in front seat ..............................79
in rear seat ................................79
Cleaning your vehicle ...............170
engine compartment ..............172
exterior .............................171,172
exterior lamps .........................172
instrument panel ....................173
instrument panel lens ............173
interior ..............................173,174
mirrors .....................................172
plastic parts ............................171
safety belts ..............................174
washing ....................................170
waxing .....................................171
wheels ......................................171
windows ..................................174
wiper blades ............................172
woodtone trim ........................174

Climate control (see Air conditioning or Heating) ............36
Clock .......................................24,32
Clutch

fluid ..........................................136
operation while driving ............97
recommended shift speeds ......99

Coolant

checking and adding ..............137
refill capacities .................141,175
specifications ...................176,177

Cruise control (see Speed control) ....................43
Customer Assistance ................105

Ford accessories for your vehicle ......................189
Ford Extended Service Plan ............................182
Getting assistance outside the U.S. and Canada ..............188
Getting roadside assistance ...105
Getting the service you need ....................182
Ordering additional owner’s literature ...................192
The Dispute Settlement Board ...................185
Utilizing the Mediation/ Arbitration Program ...............188

Daytime running lamps (see Lamps) ................................41
Defrost

rear window ..............................40

Dipstick

Doors

automati c transmission fluid ................143
engine oil .................................132

lubricant specifications ..........176

Driving under special conditions

through water .........................104

Emergencies, roadside

jump-starting ..........................119
Emission control system ..........161
Engine .................................177,178

check engine/ service engine soon light ...........9
cleaning ...................................172

Index

coolant .....................................137
idle speed control ...................146
lubrication specifications ...................176,177
refill capacities ........................175
service points ...................130,131
starting after a collision .........106
Engine block heater ...................87
Engine oil ..................................132
checking and adding ..............132
dipstick ....................................132
filter, specifications .........134,175
recommendations ...................134
refill capacities ........................175
specifications ...................176,177
Exhaust fumes ............................88
Floor mats ...................................52
Fluid capacities .........................175
Foglamps .....................................42
Fuel ............................................153
calculating fuel economy .......158
cap ...........................................155
capacity ...................................175
choosing the right fuel ...........156
comparisons with EPA fuel economy estimates .................161
detergent in fuel .....................157
filling your vehicle with fuel .......153,155,158
filter, specifications .........158,175
fuel pump shut-off switch .....106
gauge .........................................13
improving fuel economy ........158
low fuel warning light ................8
octane rating .............156,177,178
quality ......................................157
running out of fuel .................157
safety information relating to automotive fuels .....................153
Fuses ...................................108,110
Gas cap (see Fuel cap) ............155

195

Index

Gas mileage (see Fuel economy) .................158
Gauges ....................................12,13

engine coolant temperature gauge ...................13
fuel gauge ..................................13
odometer ...................................14
speedometer .............................14
tachometer ................................15
trip odometer ............................14

GAWR (Gross Axle Weight Rating) .....100
definition .................................100
driving with a heavy load ......100
location ....................................100

GVWR (Gross Vehicle Weight Rating) .............100
calculating ...............................100
definition .................................100
driving with a heavy load ......100
location ....................................100
Hazard flashers .........................106
Head restraints ...........................60
Headlamps ...................................41
aiming ...............................168,169
bulb specifications ..................168
daytime running lights .............41
flash to pass ..............................42
high beam ............................11,42
replacing bulbs .......................163
turning on and off ....................41
warning chime ..........................12
Heating ........................................36
heater only system ...................36
heating and air conditioning system ............37
Hood ..........................................129
Ignition ................................177,178
positions of the ignition ...........41
Infant seats (see Safety seats) ..78
Inspection/maintenance (I/M) testing ..............................162

196

Instrument panel

..........................8
cleaning ...................................173
cluster ...................................8,173
lighting up panel and interior .....................16
location of components ..............8
Jump-starting your vehicle ......119
Keys

key in ignition chime ...............12
positions of the ignition ...........41

Lamps

bulb replacement specifications chart ................168
cargo lamps ...............................16
daytime running light ...............41
fog lamps ...................................42
headlamps ..........................41,163
headlamps, flash to pass ..........42
instrument panel, dimming .....16
interior lamps ....................49,167
replacing bulbs ..163,165,166,167

Lane change indicator (see Turn signal) ........................43
Lights, warning and indicator ......8
air bag ........................................10
anti-lock brakes (ABS) .......11,90
anti-theft ...................................11
brake ..........................................10
charging system ........................11
high beam .................................11
low fuel ........................................8
oil pressure ...............................12
safety belt .................................10
service engine soon ....................9
turn signal indicator .................11
Load limits .................................100
GAWR ......................................100
GVWR ......................................100
trailer towing ..........................100

Locks

childproof ..................................50
Lubricant specifications ....176,177

Manual transaxle .........................97
fluid capacities ........................175
lubricant specifications ..........177
reverse .......................................99

Mirrors

cleaning ...................................172
side view mirrors (power) .......17
Moon roof ....................................49
Motorcraft parts .................158,175
Octane rating ............................156
Odometer .....................................14
Oil (see Engine oil) ..................132
Panic alarm feature, remote entry system ................................55
Parking brake ..............................90
Parts (see Motorcraft parts) ....175
Power distribution box (see Fuses) ...............................113
Power door locks ........................50
Power steering ............................91
fluid, checking and adding ....142
fluid, refill capacity ................175
fluid, specifications ..........176,177
Radio ............................................18
Relays .................................108,115
Remote entry system ............53,55
illuminated entry ......................57
locking/unlocking doors ...........54
opening the trunk .....................55
panic alarm ...............................55
replacement/additional transmitters ...............................56
replacing the batteries .............55
Roof rack ...................................104
Safety belts (see Safety restraints) ................12,63,64,65,66
Safety defects, reporting ..........193
Safety restraints ...........63,64,65,66
belt minder ...............................68
cleaning the safety belts ...71,174
extension assembly ..................67
for adults .........................64,65,66

Index

for children ..........................76,77
lap belt ......................................66
warning light and chime ...................10,12,67,68
Safety seats for children ............78
Seat belts (see Safety restraints) ...............63
Seats ............................................60
child safety seats ......................78
cleaning ............................173,174
Servicing your vehicle ..............125
Spark plugs, specifications ...............175,177,178
Specification chart, lubricants ............................176,177
Speed control ..............................43
Speedometer ...............................14
Starting your vehicle .............84,87
jump starting ..........................119

Steering wheel

tilting .........................................47
Tachometer .................................15
Temperature control (see Climate control) .................36
Tires ......................115,149,150,151
changing ...........................115,116
checking the pressure ............151
replacing ..................................152
rotating ....................................151
snow tires and chains ............152
tire grades ...............................150
treadwear ................................150
Towing .......................................151
wrecker ....................................124

Transaxle

automatic operation .................92
fluid, refill capacities ..............175
lubricant specifications ..........177
manual operation ......................97

Transmission

fluid, checking and adding (automatic) .............................143

197

Warning lights (see Lights) .........8
Washer fluid ..............................136
Water, Driving through .............104
Windows

power .........................................51

Windshield washer fluid and wipers

checking and adding fluid .....136
checking and cleaning ............149
operation ...................................48
replacing wiper blades ...........149
Wrecker towing .........................124

Index

fluid, checking and adding (manual) .................................145
lubricant specifications ..........176
Trip odometer .............................14
Trunk ...........................................52
remote release .....................17,55
Turn signal .............................11,43
Vehicle dimensions ...................178
Vehicle Identification Number (VIN) ..........................................181
Vehicle loading ..........................100
Ventilating your vehicle .............88
Warning chimes ...........................12

198

199

Filling station information

Item Required fuel Fuel tank capacity Tire size and pressure

Hood release

Oil capacity (includes filter change) Engine oil

Coolant capacity 1

Information Unleaded fuel only - 87 octane 48.5L (12.8 gallons) Refer to the Certification Label inside of driver’s door. Pull handle under the left side of the instrument panel. Sedan/wagon-3.8L (4.0 quarts) ZX2-4.25L (4.5 quarts) Use Motorcraft SAE 5W-30 Super Premium Motor Oil, Ford specification WSS-M2C153-G Automatic transaxle-6.0L (6.3 quarts) Manual transaxle-5.0L (5.3 quarts) Fill to line on reservoir. 3.9L (4.1 quarts) 3.35L (3.55 quarts)

Power steering fluid capacity Automatic transaxle capacity Manual transaxle capacity 1 Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter.

200

Before driving

Introduction

Instrumentation

Controls and features

Seating and safety restraints

Starting and driving

Starting

Driving

Roadside emergencies

Servicing

Maintenance and care

Capacities and specifications

Customer assistance

Reporting safety defects

Index

Contents

16

60

84

89

105