2004 Dodge RAM Diesel Owners Manual

Download PDF Manual
SECTION TABLE OF CONTENTS PAGE INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317 MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383 IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401 10 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411 10 INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m A Message From DaimlerChrysler Corporation . . . 4 m How To Use This Manual . . . . . . . . . . . . . . . . . . 5 m Warnings And Cautions . . . . . . . . . . . . . . . . . . . 5 m Van Conversions/Campers . . . . . . . . . . . . . . . . . 6 m Vehicle Identification Number . . . . . . . . . . . . . . . 6 m Vehicle Modifications / Alterations . . . . . . . . . . . 7 4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instruc- tions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle. NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold, so that the new owner will be aware of all safety warnings. When it comes to service, remember that your dealer knows your vehicle best, has the factory-trained techni- cians and genuine Mopart parts, and is interested in your satisfaction. WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. A MESSAGE FROM DAIMLERCHRYSLER CORPORATION DaimlerChrysler Corporation and Cummins welcome you as a new Dodge Ram Cummins Turbo Diesel- powered truck owner. Almost 100% of the heavy duty trucks in the United States are diesel powered because of the fuel economy, rugged durability, and high torque which permits pulling heavy loads. Cummins engines power well over half of these trucks. Now this same technology and proven performance is yours in your new Dodge Ram truck equipped with the Cummins 5.9 liter, Turbocharged, Charge Air Cooled, Diesel engine. Your diesel truck will sound, feel, drive, and operate differently from a gasoline-powered truck. It is important that you read and understand this manual. You may find that some of the starting, operating, and maintenance procedures are different. However, they are simple to follow and careful adherence to them will ensure that you take full advantage of the features of this engine. Thank you for choosing the Dodge Ram truck with Cummins Turbo Diesel power. INTRODUCTION 5 HOW TO USE THIS MANUAL Consult the table of contents to determine which section contains the information you desire. The detailed index, at the rear of this manual, contains a complete listing of all subjects. WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions. 6 INTRODUCTION VAN CONVERSIONS/CAMPERS The Manufacturer’s Warranty does not apply to body modifications or special equipment installed by van conversion/camper manufacturers/ body builders. Such equipment includes video monitors, VCRs, heaters, stoves, refrigerators, etc. For warranty coverage and service on these items, contact the applicable manufac- turer. Operating instructions for the special equipment in- stalled by the conversion/camper manufacturer should also be supplied with your vehicle. If these instructions are missing, please contact your selling dealer for assis- tance in obtaining replacement documents from the applicable manufacturer. VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on a stamped plate located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment. VEHICLE MODIFICATIONS / ALTERATIONS INTRODUCTION 7 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. NOTE: It is illegal to remove the VIN plate. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . .11 N Key-In-Ignition Reminder . . . . . . . . . . . . . . . .11 N Sentry Key — If Equipped . . . . . . . . . . . . . . . .11 m Ignition And Steering Lock . . . . . . . . . . . . . . . . .14 N Manual Transmissions . . . . . . . . . . . . . . . . . . .14 N Automatic Transmissions . . . . . . . . . . . . . . . . .15 m Door Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 m Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 N Manual Locks . . . . . . . . . . . . . . . . . . . . . . . . .16 N Power Door Locks — If Equipped . . . . . . . . . .17 N Child Protection Door Lock . . . . . . . . . . . . . . .21 m Remote Keyless Entry — If Equipped . . . . . . . . .22 N To Unlock The Doors . . . . . . . . . . . . . . . . . . .23 N To Lock The Doors . . . . . . . . . . . . . . . . . . . . .24 N Using The Panic Alarm . . . . . . . . . . . . . . . . . .25 N Programming Additional Transmitters . . . . . . . .26 N General Information . . . . . . . . . . . . . . . . . . . .27 N Transmitter Battery Service . . . . . . . . . . . . . . .28 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE m Windows m Security Alarm System — If Equipped . . . . . . . . .29 N Rearming Of The System . . . . . . . . . . . . . . . . .29 N To Set The Alarm . . . . . . . . . . . . . . . . . . . . . .29 N To Disarm The System . . . . . . . . . . . . . . . . . . .30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 N Power Windows—If Equipped . . . . . . . . . . . . .31 N Sliding Rear Window—If Equipped . . . . . . . . .32 N Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . .33 m Occupant Restraints . . . . . . . . . . . . . . . . . . . . . .33 N Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . .34 N Adjustable Upper Shoulder Belt Anchorage . . . .41 N Automatic Locking Mode (If Equipped) . . . . . .41 N Center Lap Belts . . . . . . . . . . . . . . . . . . . . . . .42 N Seat Belt Pretensioners . . . . . . . . . . . . . . . . . . .42 N Enhanced Driver Seat Belt Reminder System (BeltAlert) . . . . . . . . . . . . . . . . . . . . . . . . . . .43 N Seat Belts And Pregnant Women . . . . . . . . . . . .44 N Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .44 N Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbag . . . . . . . . . . . .45 N Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .55 m New Engine Break-In . . . . . . . . . . . . . . . . . . . . .67 m Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 N Transporting Passengers . . . . . . . . . . . . . . . . .68 N Lock Your Vehicle . . . . . . . . . . . . . . . . . . . . . .69 N Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .69 N Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 N Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith. If you received your keys without the bag, ask your dealer to give you the number. Key-In-Ignition Reminder If you open the driver’s door when the key is in the ignition switch, a chime will sound to remind you to remove the key. CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 SENTRY KEY — IF EQUIPPED With this system, an electronically coded ignition key sends a signal to the vehicle electronics. If the electronics recognizes the signal, the vehicle will start and continue to run. If the system does not recognize the signal the vehicle will start and run for a maximum of 2 seconds after the initial key ON. After six unsuccessful attempts at starting, the system will shut down until the correct key is used. NOTE: The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Additional Sentry Keys or Mobil Speed-pass™ devices held against or immediately adjacent to the ignition key when starting the engine may cause vehicle starting problems. If a problem occurs, remove the Sentry Key from the key-ring and attempt to start the vehicle again. Pagers, cell phones, walkman, etc. will have no effect on this system. 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The 9Security Light9, located in the instrument cluster, will illuminate for about 2 seconds when the ignition switch is first turned to the ON position. If the vehicle electronics do not receive a valid signal from the ignition key, the 9Security Light9 will flash continuously to signal that the vehicle has been immobilized. If the 9Security Light9 remains on during vehicle operation, it indicates a fault in the system electronics. If this option was ordered, all of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it cannot be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed and needs to be cut. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer. Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1. Insert the first valid key into the ignition and turn the ignition to the ON position for at least 3 seconds but no longer than 15 seconds. Turn the ignition back to the OFF position and remove the first key. 2. Insert the second valid key and switch the ignition to the ON position within 15 seconds. After 10 seconds the 9Security Light9 will begin to flash. Turn the ignition back to the OFF position and remove the second key. 3. Insert a blank Sentry Key into the ignition and switch the ignition to the ON position within 60 seconds of having removed the second key. After 10 seconds the 9Security Light9 will stop flashing, then turn on for 3 seconds; then turn off. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 The new Sentry Key has been programmed. Repeat this process to program up to an additional 6 keys. A maxi- mum of 8 keys can be programmed to the system, including the original keys provided with the vehicle. General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE IGNITION AND STEERING LOCK Manual Transmissions When the steering wheel is in the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily. To remove the key, depress and hold the release button located between the ignition switch and the instrument panel. Turn the igni- tion key to LOCK and remove the key. Manual Transmissions Automatic Transmissions In the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your ve- hicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily. The key can be inserted or withdrawn only in the LOCK position. Push in on the key in the ignition lock cylinder to rotate to the LOCK position. NOTE: The steering wheel will the lock when the key is removed, and the steering wheel is turned around 115 degrees from center clockwise and around 65 degrees counter-clockwise. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Automatic Transmissions NOTE: On vehicles equipped with an automatic trans- mission, the key cannot be turned to LOCK until the selector is in the PARK position. Do not attempt to pull the shift lever out of PARK after the key is in the LOCK position. 16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR KEY The same key used to start the vehicle is also used to unlock the doors. To unlock the vehicle doors, insert the key into the lock and turn. To lock the doors, insert the key and turn. DOOR LOCKS Manual Locks Front and Rear doors may be locked, by moving the lock plunger up or down. All doors may be opened with the inside door handle without lifting the lock plunger. Doors locked before closing will remain locked when closed. The ignition key will unlock all the locks on your vehicle. WARNING! For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal inju- ries and death. Power Door Locks — If Equipped NOTE: Vehicles equipped with remote keyless entry do not have a passenger side door lock cylinder. Vehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pressing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob (if equipped). THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a safety feature the doors will not lock when using the door lock switches during the following condition: 1. The driver’s door is open while the key is in the ignition. Central Locking — If Equipped Vehicles with security will have a feature called 9Central Locking9. When the key is placed in the door cylinder and turned to the 9Unlock9 position, the security will be disarmed, the illuminated entry will be turned on and that door will be mechanically unlocked. If the key is once again turned to the unlock position within 5 seconds of the first unlock, the remaining doors will unlock. If the key is turned to the 9Lock9 position while all doors are closed, illuminated entry will be canceled, security will begin arming, and all doors will lock. Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph. This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 4. Within 10 seconds cycle the key from the OFF position to the ON position four times; ending in the ON position ( Do not start the engine ). 5. Within 30 seconds, press the driver’s door lock switch in the LOCK direction. 6. A single chime will be heard to indicate the feature has been disabled. 7. To reactivate this feature, repeat the above steps. 8. If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat the above procedure. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Auto Unlock Feature This feature unlocks all the doors of the vehicle when the driver’s door is opened first. The following conditions must be met: † The driver’s door must be opened first. † The Automatic Door Lock feature must be enabled. † The doors of the vehicle must be locked automatically † The vehicle is in P (Park) and the ignition switch is in by the Automatic Door Lock feature. the Off position. This feature will not operate if any of the conditions above are not met or following has occurred: † Any manual operation of a door lock switch has occurred. 20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock Feature Programming This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: Customer Programming sequence to disable or enable: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may be confusing during this program- ming procedure). 3. Insert the key into the ignition. 4. Within 4 seconds, cycle the key from the OFF position to the ON position four times ending in the ON position (do not start the engine). 5. Within 30 seconds, press the driver’s door lock switch in the UNLOCK direction. 6. A single chime will sound to indicate the feature has been changed. 7. To reactivate the feature, repeat the above steps. 8. If a chime is not heard, program mode was canceled before the feature could be changed. If necessary repeat the above procedure. Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the child- protection door lock system. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position. 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! REMOTE KEYLESS ENTRY — IF EQUIPPED Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position. NOTE: For emergency exit with the system engaged, move the door lock switch to the UNLOCK position, roll down the window and open the door with the outside door handle. This system allows you to lock or unlock the doors from distances up to about 23 feet (7 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system. To unlock the doors: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and if installed, the cargo lamp will turn on for 30 seconds. The system can be programmed to unlock all the doors upon the first UNLOCK button press by using the following procedure: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt.(Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 4. Turn the ignition to the ON position ( Do not start the engine ). 5. Press and hold the UNLOCK button on a programmed (i.e. functional) key fob. 6. Continue to hold the UNLOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the LOCK button. 7. When a single chime is heard, release both buttons. 8. Turn the ignition to the OFF position or wait 60 seconds. 9. To reactivate this feature, repeat the above steps. 10. If a chime is not heard, program mode was canceled before the feature could be changed. If necessary, repeat the above procedure. 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To lock the doors: Press and release the LOCK button on the transmitter to lock all doors. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once. The horn chirp feature will be shipped from the assembly plants activated. If desired this feature can be disabled by using the following procedure: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this program- ming procedure). 3. Place the key into the ignition. 4. Turn the ignition to the ON position ( Do not start the engine ). 5. Press and hold the LOCK button on a programmed (i.e. functional) key fob. 6. Continue to hold the LOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the UNLOCK button. 7. When a single chime is heard, release both buttons. 8. Turn the ignition to the OFF position or wait 60 seconds. 9. Test the horn chirp feature by pressing the LOCK button on the key fob with the ignition in the OFF position, or the key removed. 10. To reactivate this feature, repeat the above steps. Vehicles will be shipped from the assembly plants with the park lamp flash feature activated. If desired, this feature can be disabled by using the following procedure: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this program- ming procedure). 3. Place the key into the ignition. 4. Turn the ignition to the ON position ( Do not start the engine ). 5. Press and hold the LOCK button on a programmed (i.e. functional) key fob. 6. Continue to hold the LOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the PANIC button. 7. When a single chime is heard, release both buttons. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 8. Turn the ignition to the OFF position or wait 60 seconds. 9. Test the park lamp flash feature by pressing the LOCK button on the key fob with the ignition in the OFF position or the key removed. 10. To reactivate this feature, repeat the above steps. 11. If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat the above procedure. Using the Panic Alarm To activate the Panic mode while the ignition is OFF press and release the PANIC button on the transmitter once. When the Panic mode is activated, the interior lights will illuminate, the headlamps and parking lights will flash, and the horn will sound. To cancel the Panic mode press and release the PANIC button on the transmitter a second time. Panic mode will 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE automatically cancel after 3 minutes or if the vehicle is started and exceeds 15 mph. During the Panic Mode, the door locks and remote keyless entry systems will func- tion normally. Panic mode will not disarm the security system on vehicles so equipped. Programming Additional Transmitters Vehicles with the keyless entry option will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle. A total of four fobs can be programmed for your vehicle. Additional fobs can be programmed to your vehicle through the use of a cur- rently programmed fob. NOTE: When entering program mode using that fob, ALL currently programmed fobs will be erased and you will have to reprogram them for your vehicle. However, if program mode is entered and no action is performed, the previously programmed fobs will continue to func- tion. 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this program- ming procedure). 3. Place the key into the ignition. 4. Turn the ignition to the ON position ( Do not start the engine ). 5. Press and hold the UNLOCK button on a programmed (i.e. functional) key fob. 6. Continue to hold the UNLOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the PANIC button. 7. When a single chime is heard, release both buttons. The chime indicates that the system is in program mode. 8. Press and release both the LOCK and UNLOCK buttons, simultaneously on the fob to be programmed. 9. A single chime will be heard. The chime indicates that the fob has been recognized. 10. Within 4 seconds of hearing the chime, press and release any button on the fob being programmed. 11. A single chime will be heard. The chime indicates that the fob has been programmed. 12. Repeat steps 8 to 11 for a total of 4 fobs. 13. Turn the ignition to the OFF position or wait 60 seconds to exit program mode. 14. Your vehicle will remain in program mode for up to 60 seconds from when the original chime (i.e. Step #7) was heard. After 60 seconds, all programmed fobs will function normally. NOTE: contact your dealer for details. If you do not have a programmed transmitter, THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. If your Keyless Entry Transmitter fails to operate from a normal distance, check for these two conditions. 1. Weak batteries in transmitter. The expected life of the batteries is from one to two years. 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. Transmitter Battery Service The recommended replacement battery is a 3V lithium 2016 cell. This transmitter requires two batteries. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. With transmitter buttons facing down, use a flat blade or dime to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal. 2. Remove and replace the batteries. Be careful not to disturb the metal terminal near the batteries. Install the batteries with the positive terminal up, reference the note 9+ SIDE UP9 on the inside of the bottom half of the transmitter case. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To reassemble the transmitter case snap the two halves together. Make sure there is an even gap between the two halves. Test transmitter operation. SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals. For the first 3 minutes the horn will sound and the headlights and security telltale will flash repeatedly. For an addi- tional 15 minutes only the headlights and security telltale will flash. The engine will run only if a valid Sentry Key is used to start the vehicle. Use of the Sentry Key will disable the alarm. Rearming of the System: The security system will rearm itself after the 15 addi- tional minutes of headlights and security telltale flashing, if the system has not been disabled. If the condition which initiated the alarm is still present, the system will ignore that condition and monitor the remaining doors and ignition. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To Set the Alarm: The alarm will set when you use the power door locks, turn the key in the driver’s door lock cylinder, or use the Keyless Entry transmitter to lock the doors. After all the doors are locked and closed the SECURITY light in the instrument cluster will flash rapidly to signal that the system is arming. The security light in the instrument panel cluster will flash rapidly for about 16 seconds to indicate that the alarm is being set. After the alarm is set, the security light will flash at a slower rate to indicate that the system is armed. If the SECURITY light stays on continuously NOTE: during vehicle operation, have the system checked by your dealer. 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm the System: Use the Keyless Entry transmitter or the key to turn the driver’s door lock to the unlock position. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds. Check the vehicle for tampering. The Security system will also disarm, if the vehicle is started with a programmed Sentry Key. If an unpro- grammed Sentry Key is used to start a vehicle, the engine will run for 2 seconds and then the security alarm will be initiated. To exit alarming mode, press the transmitter Unlock button, unlock the driver’s door using the key cylinder, or start the vehicle with a programmed Sentry Key. The Security Alarm System is designed to protect your vehicle; however, you can create conditions where the system will arm unexpectedly. If you remain in the vehicle and lock the doors with the transmitter, the alarm will sound when you pull the door handle to exit. You may also accidentally disarm the system by unlocking the driver’s door with the door key and then locking it manually with the lock plunger. The door will be locked but the Security Alarm will not arm. WINDOWS Power Windows—If Equipped THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab models. The windows will operate only when the ignition switch is turned to the ON or ACC (Accessory) position. 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. Window Lockout Switch (4 Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lock button. To enable the window controls, press the window control button again. Sliding Rear Window—If Equipped A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. WIND BUFFETING Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger and, if so equipped, window bags for the driver and passengers seated next to a window. If you will be carrying children too small for adult-size belts, your seat belts also can be used to hold infant and child restraint systems. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions except the Quad Cab front center seating position have combination lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out. WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a seat belt properly. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. WARNING! † Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instruc- tions to wear your seat belt safely and to keep your passengers safe, too. † Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! † A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. † A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increas- ing the possibility of injury. Wear your seat belt snugly. † A belt that is worn under your arm is very danger- ous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. And a belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. † A shoulder belt placed behind will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! † A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. † A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed. 5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.) or if the airbag deployed. Standard Cab Front Center Three Point Belt 1. The front center seat belt on the Standard Cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger seat. Insert the vehicle ignition key into the center white slot on the black buckle. The black buckle latch plate can be removed when the key is pressed into the buckle. Allow the retractor to take up the surplus webbing, and the buckles will hang vertically from the cab back exit bezel, thus freeing up all the area behind the front seats. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! † If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. † When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted. If the webbing is twisted, follow the preceding procedure to detach the black latch and black buckle, untwist the webbing, and reattach the black latch and black buckle. Detaching Buckle with Key 2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage. 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Inserting Latch Plate In Use Position WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly. Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that serves you best. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Automatic Locking Mode (if Equipped) In this mode, the shoulder belt is automatically pre- locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is only available on the front passenger side belt. When To Use The Automatic Locking Mode Anytime a child safety seat is installed in a passenger front seating position. Children 12 years old and under should be properly restrained in the rear seat whenever possible. How To Use The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How To Disengage The Automatic Locking Mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic lock- ing mode and activate the vehicle sensitive (emergency) locking mode. Center Lap Belts The center seating position for the Quad Cab front seat has a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a 9click.9 To lengthen the lap belt, tilt the latch plate and pull. To remove slack, pull the loose end of the webbing. Wear the lap belt snug against the hips. Sit back and erect in the seat, then adjust the belt as tightly as is comfortable. WARNING! and under the belt in a collision. † A lap belt worn too loose or too high is dangerous. † A belt worn too loose can allow you to slip down † A belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones. In either case, the risk of internal injuries is greater. Wear a lap belt low and snug. Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove any slack from the seat belt system in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints. NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the airbag control module. Like the airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced. Enhanced Driver Seat Belt Reminder System (BeltAlert) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts. Once the warning is triggered, the Enhanced Warning System (BeltAlert) will continue to chime and flash the Seat Belt Warning Light for 96 seconds or until the driver’s seat belt is buckled. The THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Enhanced Warning System (BeltAlert) will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). The Enhanced Warning System (BeltAlert) can be en- abled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. DaimlerChrysler does not recom- mend deactivating the Enhanced Warning System (BeltAlert). 1. Turn the ignition switch to the OFF position and buckle the driver’s seat belt. 2. Start the engine and wait for the Seat Belt Warning Light to turn off. 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the pro- gramming. The Enhanced Warning System (BeltAlert) can be reacti- vated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltA- lert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s seat belt remains unbuckled. Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Seat Belt Extender If a seat belt is too short, even when fully extended, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the ex- tender and store it. WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbag This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 These airbags are certified to the new Federal regulations that allow less forceful deployments. This vehicle may also be equipped with window bags to protect the driver and passengers in the first and second row sitting next to a window. If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also labeled SRS AIRBAG. 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! † Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. † Do not mount any aftermarket equipment such as trailer brake controllers, snowplow controllers, auxiliary light switches, radios, etc. on or behind the knee bolster. Knee bolsters are designed to work with the air bag and seat belt to protect you. Mounting any additional equipment on or behind the knee bolster can cause injury during a crash. † If your vehicle is equipped with window bags, do not stack luggage or other cargo up high enough to block the location of the window bag. The area where the window bag is located should remain free from any obstructions. † If your vehicle is equipped with window bags, do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that require permanent attachments (bolts or screws) for installation on the vehicle roof. Do not drill into the roof of the vehicle for any reason. Airbags inflate in moderate to high speed impacts. Along with the seatbelts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions. If your vehicle is so equipped, the window bag on the crash side of the vehicle is triggered in moderate to severe side collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can follow to minimize the risk of harm from a deploying airbag. † Children 12 years and under should ride buckled up in a rear seat, if available. † Infants in rear facing child restraints must NEVER ride in the front seat of a vehicle with a passenger front airbag unless the airbag is turned off (Standard Cab Vehicles Only). An airbag deployment can cause se- vere injury or death to infants in that position. See the Passenger Airbag On/Off Switch section. † If your vehicle does not have a rear seat, see the † Children that are not big enough to properly wear the vehicle seat belt (see section on Child Restraints) should be secured in the rear seat in child restraints or belt-positioning booster seats. Older children who do not use child restraints or belt-positioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. Passenger Airbag On/Off Switch section. † All occupants should use their seat belts properly. † The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 WARNING! † Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. † Being too close to the steering wheel or instru- ment panel during airbag deployment could cause serious injury. Airbags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. † If the vehicle has window airbags, they also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The airbag system consists of the following: † Airbag Control Module † AIRBAG Readiness Light † Driver Airbag † Passenger Airbag † Steering Wheel and Column † Instrument Panel † Crash Sensor † Interconnecting Wiring † Knee Impact Bolsters † Passenger Side Frontal Airbag ON/OFF Switch (Stan- dard Cab Vehicles Only) system) system) The Window Airbag System, on vehicles equipped, consists of the following: † AIRBAG Readiness Light (shared with the front airbag † Window Bags Above the Side Windows. † Airbag Control Module (shared with the front airbag † Side impact sensors † Interconnecting Wiring How The Airbag System Works † The airbag control module determines if a frontal collision is severe enough to require the airbags to inflate. † The airbag control module will not detect roll over, or rear collisions. † The airbag control module also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the knee bolsters, the instrument panel, and the steering wheel and column. If the key is in the 9Off9 position, in the ACC position or not in the ignition, the airbags are not on and will not inflate † The airbag control module also turns on the AIR BAG light in the instrument panel for 6 to 8 seconds when the ignition is first turned on, then turns the light off. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 † If it detects a malfunction in any part of the system, it turns on the light either momen- tarily or continuously. The instrument cluster will flash the seat belt indicator if it detects a fault with the airbag indicator. WARNING! Ignoring the AIR BAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE † When the airbag control module detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags. The airbag covers separate and fold out of the way as the airbags inflate to their full size. The airbags fully inflate in milliseconds. This is less time than it takes you to blink your eyes. The airbags then quickly deflate while helping to restrain the driver and front passenger. The driver’s front airbag deflates through vents towards the instrument panel. The passenger’s front airbag is deflated through vent holes in the sides of the airbag. In this way the airbags do not interfere with your control of the vehicle. † The knee impact bolsters help protect the knees and position you for the best interaction with the front airbag. Passenger Airbag On/Off Switch – (Standard Cab Vehicles Only) The passenger front airbag is to be turned off only if the passenger: † is an infant (less than 1 year old) who must ride in the front seat because there is no rear seat, because the rear seat is too small for a rear-facing infant restraint or because the infant has a medical condition which makes it necessary for the driver to be able to see the infant, † is a child, age 1 to 12 who must ride in the front seat because there is no rear seat, because there is no rear seat position available, or because the child has a medical condition which makes it necessary for the driver to be able to see the child, † has a medical condition which makes passenger airbag inflation (deployment) a greater risk for the passenger than the risk of hitting the dashboard (instrument panel) or windshield in a crash. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death. To Shut Off the Passenger Airbag (Standard Cab Ve- hicles Only) Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn clockwise, and remove the key from the switch. This will shut off the passenger side airbag. The “Off” light near the switch will illumi- nate when the ignition switch is turned to the ON position. 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Turn On the Passenger Airbag (Standard Cab Ve- hicles Only) Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn counterclockwise, and remove the key from the switch. This will turn on the passenger airbag. The “Off” light near the switch will be off when the ignition switch is turned to the ON position. If A Deployment Occurs The airbag system is designed to deploy when the air bag control module detects a moderate-to-severe frontal col- lision, and then immediately to deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: † The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. † As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instruc- tions for cleaning. † It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you. WARNING! Deployed airbags can’t protect you in another colli- sion. Have the airbags replaced by an authorized dealer as soon as possible. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Window Airbags Supplemental Restraint System (SRS)—If Equipped The window airbag control module determines if a side collision is severe enough to require the side airbags to inflate. The window airbag control module will not detect roll over, front or rear collisions. The airbag control module monitors the readiness of the electronic parts of the system whenever the ignition switch is in the 9START9 or 9RUN9 positions. These include all of the items listed above. The airbag control module also turns on the AIRBAG light in the instrument panel for 6 to 8 seconds when the ignition is first turned on as a diagnostic or system check, then turns the light off. If it detects a malfunction in any part of the system, it turns on the light either momentarily or continuously. The side (window) impact SRS Airbags are designed to activate only in certain side collisions. When the airbag control module detects a collision requiring the window 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE bags to inflate, it signals the inflators on the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the window bag. The inflating window bag pushes the side pillar molding out of the way and covers the window. The airbag inflates in about 30 milliseconds (about one-quarter of the time it takes to blink your eyes) with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the window bag inflates. This especially applies to children. The window bag is only about 3 1⁄2 inches (8.9 cm) thick when it is inflated. Enhanced Accident Response System If the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically. In addition, approximately 10 seconds after the vehicle has stopped moving, the interior lights will light until the ignition switch is turned off. Maintaining Your Airbag Systems WARNING! † Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body struc- ture, or frame. † You need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee bolster. † It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has airbags. Airbag Light You will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system promptly: † The airbag light does not come on or flickers during the 6 to 8 seconds when the ignition switch is first turned on. † The light remains on or flickers after the 6 to 8 second † The light flickers or comes on and remains on while interval. driving. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 If the speedometer, tachometer or any engine NOTE: related gauges are not working, the airbag control mod- ule may also be disabled. The airbags may not be ready to inflate for your protection. Promptly check fuse num- bers 52 and 53 in the fuse and relay center. See your dealer if the fuse is good. Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buck- led up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size. Infants and Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Use the restraint that is correct for your child: † Safety children ride rearward-facing in the vehicle until they are at least recommend that experts one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and 9convertible9 child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt. † The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). 9Convertible9 child seats can be used either rearward-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs (9 kg) but are less than one year old. † Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. † Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt. † The belt-positioning booster seat is for children weigh- ing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seat back, they should use a belt-positioning-booster seat. The child and booster seat are held in the vehicle by the lap/shoulder belt. (Some booster seats are equipped THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 with a front shield and are held in the vehicle by the lap portion.) For to www.seatcheck.org. information refer further WARNING! † Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. † A rearward facing child restraint should only be used in a rear seat, or in the front seat if the passenger’s front airbag is Off. If the airbag is left On, a rearward facing child restraint in the front seat may be struck by a deploying passenger airbag which may cause severe or fatal injury to the infant. 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child restraint: † Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it. † The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. † Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it. † The passenger seat belts are equipped with either cinching latch plates or switchable seat belt retractors, which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. If the seat belt has a switchable retractor, it will have a distinctive label: Pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then pull on the belt until it is all removed from the retractor. Allow the belt to return to the retractor, pulling on the excess webbing to tighten the lap portion about the child restraint. Refer to the 9Automatic Locking Mode9 earlier in this section. † In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. † If the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. † Buckle the child into the seat according to the child † When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. restraint manufacturer’s directions. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seat backs and cause serious personal injury. WARNING! Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when install- ing an infant or child restraint. Lower Anchors and Tether for CHildren (LATCH) Each vehicle is equipped with the child restraint anchor- age system called LATCH, which stands for Lower Anchors and Tether for CHildren. LATCH child restraint anchorage systems are installed in the Standard Cab passenger seat position and the Quad Cab rear seat 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE outboard positions and also feature tether strap anchor- ages, which must be used, located behind the seatback (refer to Child Restraint Tether Anchor later in this section). Identification dots are located above the standard cab front seat lower anchorages as a guide for locating lower anchors. NOTE: For children riding in the front seat of a Stan- dard Cab model refer to the “Passenger Airbag On/Off Switch” located in this section. Standard Cab Passenger Seat 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor- ages will continue to have features for installation in vehicles using the lap or lap/shoulder belt. They will also have tether straps, and you are urged to take advantage of all of the available attachments provided with your child restraint in any vehicle. If your child restraint seat is not LATCH com- NOTE: patible, install the restraint using the vehicle seat belting. Quad Cab Outboard Seat 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the Child Restraint System WARNING! Do not install child restraint systems equipped with LATCH attachments in the center position of a Quad Cab model rear seat. The LATCH anchorages in this seat are designed for the two outboard seating posi- tions only. A child may be placed in the rear center seating position of a Quad Cab model using the seat belt and child tether anchorage. Failure to follow this may result in serious or fatal injury. We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Many, but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector and a means for adjusting the tension in the strap. Forward-facing toddler restraints and some rearward-facing infant restraints will also be equipped with a tether strap, a hook and means for adjusting the tension in the strap. In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages. Then tighten all three straps as you push the child restraint rearward and downward into the seat. Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions that come with the child restraint system. WARNING! WARNING! THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Child Restraint Tether Anchor Child restraints having tether straps and hooks for con- nection to tether anchors have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for their older products. Regular Cab models of Ram Pickups have two tether anchorages, one each behind the front center and right seats. Quad Cab models have three anchorages, one behind each of the rear seats. An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Follow the instructions below. See your dealer for help if nec- essary. 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tether Anchorage Points at the Right and Center Front Seat (Regular Cab - All Seats) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat. 2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. 3. Install the child restraint and remove the slack in the tether strap according to the manufacturer’s instructions. Regular Cab With Any Bench Seat Multiple Child Restraint Installation Sequence - (Quad Cab Rear Seats) 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly improved by raising the seat cushion to the “up” position. Remove the elastic before use. 2. Place a child restraint on each outboard rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and then to the anchor directly behind the center rear seat. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 3. Pass each tether strap hook under the head restraint and through the loop of webbing behind the child seat. 4. Route each tether strap to the anchor behind the center seat, and attach the hooks to the metal ring. 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and to the anchor directly behind the right seat. 6. Install each child restraint and remove the slack in the tether strap according to the child restraint manufactur- er’s instructions. 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Multiple Child Restraints Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. † Make sure that the child is upright in the seat. † The lap portion should be low on the hips and as snug † Check belt fit periodically. A child’s squirming or as possible. slouching can move the belt out of position. If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 NEW ENGINE BREAK-IN Your Cummins 24 Valve Turbo Diesel engine does not require a normal break-in period due to its construction. Normal operation is allowed, provided the following recommendations are followed: NOTE: Light duty operation such as light trailer towing or no load operation, will extend the time before the engine is at full efficiency. Reduced fuel economy and power may be seen at this time. † Warm up the engine before placing it under load. † Do not operate the engine at idle for prolonged † Use the appropriate transmission gear to prevent † Observe vehicle oil pressure and temperature indica- engine lugging. periods. tors. 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE † Check the coolant and oil levels frequently. † Vary throttle position at highway speeds when carry- ing or towing significant weight. Because of the construction of the Cummins Diesel engine, engine run-in is enhanced by loaded operating conditions which allow the engine parts to achieve final finish and fit during the first 6,000 miles (10 000 km). CAUTION! † During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer. Doing so may damage your vehicle. † Limit your speed to 50 mph (80 km/h) during the first 500 miles (805 km) of towing. SAFETY TIPS Transporting Passengers This vehicle is designed to carry passengers in the cab only. For safety reasons, NEVER TRANSPORT PASSEN- GERS IN THE CARGO AREA. WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a seat belt properly. Lock Your Vehicle Always remove the keys from the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. Try to park your vehicle in a well-lighted area and never invite theft by leaving ar- ticles of value exposed. Exhaust Gas WARNING! Exhaust gases contain carbon monoxide, a poten- tially toxic gas that by itself is colorless and odorless. To avoid inhaling these gases, the following precau- tions should be observed: † Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 † If it is necessary to sit in a parked vehicle with the engine running for more than a short period, adjust your climate control system to force outside air into the vehicle. Set the blower at high speed and the controls in any position except OFF or MAX A/C. † The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Be aware of changes in the sound of the exhaust system; exhaust fumes detected inside the vehicle; or damage to the underside or rear of the vehicle. Have a competent mechanic inspect the complete exhaust system and adja- cent body areas for broken, damaged, deteriorated or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace or adjust as required. 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Safety Checks You Should Make Outside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.) or if the front airbags have deployed. If there is any question regarding belt or retractor condition, replace the belt. Airbag Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see you authorized dealer. If the light stays on, flickers or comes on while driving, have the system checked by an autho- rized dealer. If there is a problem with the airbag light the seatbelt light will flash. Tires Examine tires for tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks. Check wheel nuts for tightness and tires for proper pressure. Lights Check the operation of all exterior lights. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if fuel fumes are detected the cause should be located and corrected. UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 N Inside Mirror . . . . . . . . . . . . . . . . . . . . . . . . .75 N Automatic Dimming Mirror— If Equipped . . . .76 N Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .76 N Exterior Mirrors Folding Feature . . . . . . . . . . .77 N Electronic Power Mirrors — If Equipped . . . . . .77 N Electric Rear Window Defroster And Heated Sideview Mirrors — If Equipped . . . . . . . . . . .78 N Trailer Towing Mirrors — If Equipped . . . . . . .79 m Hands–Free Communication (UConnect™) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 N Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 N Phone Call Features . . . . . . . . . . . . . . . . . . . .85 N Advanced Phone Connectivity . . . . . . . . . . . . .87 N UConnect™ System Features . . . . . . . . . . . . . .89 m Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 N 40-20-40 Front Seat . . . . . . . . . . . . . . . . . . . . .92 N Reclining Seats . . . . . . . . . . . . . . . . . . . . . . . .93 72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE N Adjustable Head Restraints . . . . . . . . . . . . . . .93 N Manual Rotary Lumbar Support Adjustment — If Equipped . . . . . . . . . . . . . . .94 N Power Seats — If Equipped . . . . . . . . . . . . . . .95 N Heated Seats — If Equipped . . . . . . . . . . . . . .96 m To Open And Close The Hood . . . . . . . . . . . . . .97 m Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 N Interior Lights . . . . . . . . . . . . . . . . . . . . . . . .99 N Battery Saver . . . . . . . . . . . . . . . . . . . . . . . . 100 N Headlamp Delay — If Equipped . . . . . . . . . . 101 N Headlights, Parking Lights, Panel Lights . . . . . 101 N Daytime Running Lights (Canada And Fleet Vehicles Only) . . . . . . . . . . . . . . . . . . . . . . . 102 N Lights-On Reminder . . . . . . . . . . . . . . . . . . . 102 N Fog Lights — If Equipped . . . . . . . . . . . . . . . 102 N Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . 103 m Multifunction Control Lever . . . . . . . . . . . . . . . 103 N Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 103 N Passing Light . . . . . . . . . . . . . . . . . . . . . . . . 104 N High Beam / Low Beam Select Switch . . . . . . 104 N Windshield Wipers . . . . . . . . . . . . . . . . . . . . 105 N Windshield Washers . . . . . . . . . . . . . . . . . . . 106 m Tilt Steering Column . . . . . . . . . . . . . . . . . . . . 107 m Driver Adjustable Pedals — If Equipped . . . . . . 108 . . . . . . . . . . . . . . . . . . . . . . . . . 108 m Electronic Speed Control — If Equipped . . . . . . 109 N To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . 109 N Adjustment N To Set At A Desired Speed . . . . . . . . . . . . . . . 110 N To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . 110 N To Resume Speed . . . . . . . . . . . . . . . . . . . . . 110 N To Vary The Speed Setting . . . . . . . . . . . . . . . 111 N To Accelerate For Passing . . . . . . . . . . . . . . . 111 m Overhead Console— If Equipped . . . . . . . . . . . 112 N Courtesy/Reading Lights . . . . . . . . . . . . . . . . 113 m Overhead Console With Compass/Temperature Mini-Trip Computer — If Equipped . . . . . . . . . . 113 N US/M Button . . . . . . . . . . . . . . . . . . . . . . . . 114 N Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . 114 N Global Reset . . . . . . . . . . . . . . . . . . . . . . . . . 115 N Step Button . . . . . . . . . . . . . . . . . . . . . . . . . 115 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 N Average Fuel Economy (AVG ECO) . . . . . . . . 115 N Distance To Empty (DTE) . . . . . . . . . . . . . . . 115 N Trip Odometer (ODO) . . . . . . . . . . . . . . . . . . 116 N Elapsed Time (ET) . . . . . . . . . . . . . . . . . . . . . 116 N C/T Button . . . . . . . . . . . . . . . . . . . . . . . . . 117 N Automatic Compass Calibration . . . . . . . . . . . 117 N Manual Compass Calibration . . . . . . . . . . . . . 118 N To Put Into a Calibration Mode . . . . . . . . . . . 118 N Outside Temperature . . . . . . . . . . . . . . . . . . . 119 m Garage Door Opener — If Equipped . . . . . . . . . 120 N Programming Homelink . . . . . . . . . . . . . . . . 121 N Canadian Programming/Gate Programming . . 123 N Using Homelink . . . . . . . . . . . . . . . . . . . . . . 124 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE N Erasing Homelink Buttons . . . . . . . . . . . . . . . 124 N Reprogramming a Single Homelink Button . . . 125 N Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 m Electrical Power Outlets . . . . . . . . . . . . . . . . . . 126 m Cigar Lighter And Ash Receiver . . . . . . . . . . . . 127 m Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 N Front Instrument Panel Cupholders — Automatic Transmission Only . . . . . . . . . . . . 128 N Rear Cupholder — Quad Cab — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 m Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 N Center Storage Compartment — If Equipped . . 129 N Storage And Seats — If Equipped . . . . . . . . . . 130 m Fold Flat Load Floor — If Equipped . . . . . . . . . 130 N Fold Flat Load Floor — If Equipped . . . . . . . . 130 m Pickup Box . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 m Slide-In Campers . . . . . . . . . . . . . . . . . . . . . . . 135 N Camper Applications . . . . . . . . . . . . . . . . . . . 135 m Easy-Off Tailgate . . . . . . . . . . . . . . . . . . . . . . . 135 MIRRORS Inside Mirror The mirror should be adjusted to center on the view through the rear window. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield). UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 Electronic Power Mirrors — If Equipped WARNING! Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side convex mirror. Some vehicles will not have a convex right side mirror. Exterior Mirrors Folding Feature All exterior mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions; full forward, full rearward, and normal. 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The controls for the power mirrors are located on the driver’s door trim panel. Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror. To adjust a mirror, select left or right with the top switch, and press one of the four arrows for the direction you want the mirror to move. Electric Rear Window Defroster and Heated Sideview Mirrors — If Equipped The Electric Rear Window Defroster and Heated side view mirrors are activated by pressing the heated grid button, located on the Climate Control panel, with the ignition On. Turning Off the ignition will deactivate the Electric Rear Window Defroster and Heated side view mirrors feature. These features also turn off after activation, when 15 minutes have elapsed. To reactivate, simply press the button again. Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or out- board, the mirror head should be rotated (flipped Out or In). A small blindspot mirror is integrated onto the main mirror surface. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in-vehicle communications system. UConnect™; allows you to dial your cellular phone using simple voice commands (e.g., phones to be linked to the system, and it is available in English, French, or Spanish formats (as equipped). The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. The diagram below shows the mirror with the appropriate buttons. Individual button behavior is discussed in the “Operation” Section. 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE “Call” or “Dial”). Your cellular phone’s audio is trans- mitted through your vehicle’s stereo system; the system will automatically mute your radio before receiving or sending a call. UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversations. The UConnect™; phone book enables you to store up to 32 names and four numbers per name. This system is driven through your Bluetooth™ Hands-Free Profile cellular phone. UConnect™ features Bluetooth™ technol- ogy - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so UConnect™ works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase). UConnect™ allows up to seven cellular The UConnect™ system can be used with any Hands Free Profile certified Bluetooth™ cellular phone. If your cellular phone has a different profile (i.e. headset profile), you will not be able to use any UConnect™ features. The UConnect™ system is fully integrated into your vehicle, including your vehicle’s stereo system. All voice prompts as well as the other party’s voice in a conversa- tion will be played over your vehicle’s stereo system. The volume of the UConnect™ system can be controlled through your normal stereo controls. The radio display will be used for visual prompts from the UConnect™ system such as caller ID. Operation Voice commands can be used in the operation of the UConnect™ system and to navigate through the UCon- nect™ menu structure. Voice commands should be given after each UConnect™ system prompt. You will be UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 prompted for a specific command and then guided through the available options. There are two ways to give commands to the UConnect™ system: † You can say 9Dial9 at the 9Ready9 prompt. When prompted for the phone number you wish to dial, say the phone number (9123 456 78909). Pairing a Cellular Phone to the UConnect™ System To begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone. To complete the registration process, you will need to refer- ence your cellular phone owner’s manual. † Press the ’Phone’ button to begin. † After the 9Ready9 prompt, say 9Setup9. † When prompted, say “ Phone Pairing”. 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE † You will be asked to say a four-digit pin number into the UConnect™ system which you will later need to enter into your cellular phone during the cellular phone pairing process. You can enter any four-digit pin number. You will not need to remember this pin number after the initial registration process. † The UConnect™ system will then prompt you to begin the cellular phone pairing process on your cellular phone. Please see your cellular phone user’s manual for instructions on how to complete this step. † For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. † You will then be asked to give your cellular phone a priority level between 1 and 7, 1 having the highest priority. You can connect up to seven cellular phones to your UConnect™ system and the priority allows the UConnect™ system to know which cellular phone to use if multiple cellular phones are in the vehicle at the same time. For example, if a priority 3 and priority 5 cellular phone are both in the vehicle, the UConnect™ system will use the priority 3 cellular phone when you make a call. You can select to use a lower priority

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2004 Dodge RAM Diesel Owners Manual