Login- 2009 Dodge Challenger SRT8 Owners Manuals
- Dodge Challenger SRT8 Owners Manuals
- 2013 Dodge Challenger SRT8 Owners Manuals
- Dodge Challenger SRT8 Owners Manuals
- 2010 Dodge Challenger SRT8 Owners Manuals
- Dodge Challenger SRT8 Owners Manuals
- 2012 Dodge Challenger SRT8 Owners Manuals
- Dodge Challenger SRT8 Owners Manuals
- 2008 Dodge Challenger SRT8 Owners Manuals
- Dodge Challenger SRT8 Owners Manuals
- 2011 Dodge Challenger SRT8 Owners Manuals
- Dodge Challenger SRT8 Owners Manuals
- Download PDF Manual
-
350 MAINTAINING YOUR VEHICLE
reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water. When refilling the washer fluid reservoir, apply some washer fluid to a cloth or towel and wipe the wiper blades clean. This will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. The fluid reservoir will hold nearly 1 gal (4 l) of washer fluid when the message “Low Washer Fluid” appears in the Electronic Vehicle Information Center (EVIC).
WARNING!
Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition,
inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required.
CAUTION!
MAINTAINING YOUR VEHICLE 351
WARNING!
Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Exhaust Gas” under “Safety Tips” in Section 2.
The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device. Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
NOTE: systems can result against you.
Intentional tampering with emissions control in civil penalties being assessed
352 MAINTAINING YOUR VEHICLE
WARNING!
A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.
In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating. If this should occur, safely bring the vehicle to a complete stop, shut the engine OFF, and allow the vehicle to cool. Thereafter, obtain service, including a tune-up to manufacturer’s specifications immediately.
To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idling or malfunctioning operating conditions.
vehicle.
Cooling System
WARNING!
• When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the LOCK position. The fan is tempera- ture controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot.
Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the
MAINTAINING YOUR VEHICLE 353
system should be drained, flushed, and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the coolant recovery bottle tubing for brittle rub- ber, cracking, tears, cuts, and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks. With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of coolant from the radiator drain cock. If the cap is sealing properly, the engine coolant (antifreeze) will begin to drain from the coolant recovery bottle. DO NOT RE- MOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT.
354 MAINTAINING YOUR VEHICLE
Cooling System — Drain, Flush, and Refill If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old antifreeze solution. Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals. Selection of Coolant Use only the manufacturer’s recommended coolant. Re- fer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.
CAUTION!
• Mixing of coolants other than specified HOAT engine coolants may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the speci- fied coolant as soon as possible. • Do not use plain water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • This vehicle has not been designed for use with propylene glycol-based coolants. Use of propylene glycol-based coolants is not recommended.
Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to five years or 102,000 miles (170 000 km) before replacement. To prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) coolant. When adding coolant: • The manufacturer
recommends using MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology). • Mix a minimum solution of 50% HOAT engine coolant and distilled water. Use higher concentrations (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C) are anticipated.
MAINTAINING YOUR VEHICLE 355
• Use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system.
Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing coolant types will decrease the life of the engine coolant and will require more frequent coolant changes. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of coolant and to ensure that coolant will return to the radiator from the coolant recovery bottle.
356 MAINTAINING YOUR VEHICLE
The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
WARNING!
• The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scald- ing or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or en- gine damage may result.
Disposal of Used Coolant Used ethylene glycol-based engine coolant is a regulated substance requiring proper disposal. Check with your
local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol-based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine OFF and cold, the level of the coolant in the bottle should be between the ranges indicated on the bottle. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for coolant freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month.
When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the front of the engine compartment. This is nor- mally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot coolant to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle.
MAINTAINING YOUR VEHICLE 357
• Check the coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, the contents of the coolant recovery bottle must also be protected against freezing. • If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pres- sure tested for leaks. • Maintain coolant concentration at 50% HOAT engine coolant (minimum) and distilled water for proper corrosion protection of your engine, which contains aluminum components. • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean.
358 MAINTAINING YOUR VEHICLE
• Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions.
Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals.
WARNING!
Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency.
Master Cylinder - Brake Fluid Level Check Check the fluid level in the master cylinder immediately if the “Brake Warning Light” indicates system failure. Check the fluid level in the master cylinder when per- forming underhood services. Clean the top of the master cylinder area before removing the cap. Add fluid to bring the level up to the “MAX” mark on the side of the master cylinder reservoir. Overfilling of fluid is not recommended because it may cause leaking in the system. Add enough fluid to bring the level up to the require- ments described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed.
Use only manufacturer’s recommended brake fluid. Re- fer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.
WARNING!
• Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • Use of a brake fluid that may have a lower initial boiling point, or is unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident.
Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture.
MAINTAINING YOUR VEHICLE 359
CAUTION!
Do not allow petroleum-based fluid to contaminate the brake fluid. Seal damage may result.
Clutch Hydraulic System (Manual Transmission) — If Equipped The clutch hydraulic system is fed by a segregated volume of fluid within the brake system master cylinder reservoir. In the event of leakage or wear, use only the manufacturer’s recommended brake fluid. Refer to “Flu- ids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Manual Transmission — If Equipped
Fluid Level Check Check the fluid level by removing the fill plug on the left side of the transmission. The fluid level should be at the bottom of the fill hole. Add fluid, if necessary, to maintain
360 MAINTAINING YOUR VEHICLE
the proper level. Refer to “Fluids, Lubricants, and Genu- ine Parts” in this section for the correct fluid type.
CAUTION!
Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or damage to the transmission. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.
Change Transmission Fluid If contaminated with water, change the fluid immedi- ately. See your authorized dealer for service. Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals.
Automatic Transmission — If Equipped
Fluid Level Check Regular automatic transmission fluid level checks are not required. For this reason, the dipstick is omitted. If you notice fluid loss or gear shift malfunction, have your authorized dealer check the transmission fluid level.
CAUTION!
• Using a transmission fluid other than the manu- facturer’s recommended fluid may cause deterio- ration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genu- ine Parts” in this section for the correct fluid type. (Continued)
CAUTION! (Continued)
• The fluid level is preset at the factory and it does not require adjustment under normal operating conditions. If a transmission fluid leak occurs, visit your authorized dealer immediately. Severe damage to the transmission may occur. Your au- thorized dealer has the proper tools to adjust the fluid level accurately.
Fluid and Filter Changes Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals. If the transmission is disassembled for any reason, the fluid and filter should be changed.
MAINTAINING YOUR VEHICLE 361
Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only manufacturer’s recommended transmis- sion fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. No chemical flushes should be used in any transmission; only the approved lubricant may be used. Special Additives Automatic Transmission Fluid (ATF) is an engineered product and its performance may be impaired by supple- mental additives. Therefore, do not add any fluid addi- tives to the transmission. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks. In addition, avoid using transmission sealers as they may adversely affect seals.
362 MAINTAINING YOUR VEHICLE
Rear Axle
Fluid Level Check Check the fluid level by removing the fill plug on the axle. The fluid level should be at the bottom of the fill hole. Add fluid, if necessary, to maintain the proper level. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Change Axle Fluid Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals. Appearance Care and Protection from Corrosion
Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and chemicals that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. Outside
parking, which exposes your vehicle to airborne contami- nants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme condi- tions will have an adverse effect on paint, metal trim, and underbody protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt, and moisture accumulation. • Stone and gravel impact. • Insects, tree sap, and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants.
Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using MOPAR威 Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumu- lated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover to remove. • Use MOPAR威 Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
MAINTAINING YOUR VEHICLE 363
CAUTION!
Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces.
Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner.
364 MAINTAINING YOUR VEHICLE
• If your vehicle is damaged due to an accident or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as pos- sible. The cost of such repairs is considered the respon- sibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider • Use MOPAR威 Touch Up Paint or equivalent on scratches as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle.
mud or stone shields behind each wheel.
Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove
heavy soil and/or excessive brake dust, use MOPAR威 Wheel Cleaner (05066247AB) or equivalent or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Only MOPAR威 or equivalent is recommended. Do not use oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. Interior Care Use MOPAR威 Fabric Cleaner or equivalent to clean fabric upholstery and MOPAR威 Carpet Cleaner for carpeting. Interior Trim should be cleaned starting with a damp cloth, or MOPAR威 Satin Select. Do not use harsh cleaners or Armorall. Use MOPAR威 Total Clean to clean vinyl upholstery. MOPAR威 Total Clean is specifically recommended for leather upholstery.
Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and MOPAR威 Total Clean or equivalent. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean your leather upholstery. Application of a leather condi- tioner is not required to maintain the original condition.
WARNING!
Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.
MAINTAINING YOUR VEHICLE 365
Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass; and therefore, different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or the right rear
366 MAINTAINING YOUR VEHICLE
quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments that may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag or micro-fiber towel. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue.
Seat Belt Maintenance Do not bleach, dye, or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use MOPAR威 Total Clean, a mild soap solution, or lukewarm water. Do not remove the belts from the vehicle to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly. Cleaning The Center Console Cupholders Clean with a damp cloth or towel using a mild detergent with the cupholder in the center console. NOTE: The cupholder cannot be removed.
FUSES
Integrated Power Module (IPM) The Integrated Power Module (IPM) is located in the engine compartment. This module contains fuses and relays.
Integrated Power Module
MAINTAINING YOUR VEHICLE 367
CAUTION!
• When installing the integrated power module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the integrated power module and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected.
368 MAINTAINING YOUR VEHICLE
Cavity Car-
tridge Fuse —
Cavity Car-
Mini- Fuse
15 Amp Blue 25 Amp Neutral 25 Amp Neutral 25 Amp Neutral — 25 Amp Neutral — 25 Amp Neutral —
Description
Washer Motor
Powertrain Control Module (PCM) Ignition Run/Start
EGR Solenoid/ Alternator — Ignition Coils/Injectors
— Starter
—
10
11
12
13
14
1516
17
18
19tridge Fuse 30 Amp Pink 30 Amp Pink 40 Amp Green 50 Amp Red — 50 Amp Red — — — —
Mini- Fuse
Description
—
—
—
—
— —
— — — —
Windshield Wiper
Anti-Lock Brake System (ABS) Valves Radiator Fan Lo/High
Anti-Lock Brake System (ABS) Pump Motor — Radiator Fan
— — — —
—
—
—
— —
— —
—
Mini- Fuse
Description
MAINTAINING YOUR VEHICLE 369
Cavity Car-
tridge Fuse — — —
— — —
— — —
20
21
22
Rear Power Distribution Center There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays.Access Panel
370 MAINTAINING YOUR VEHICLE
Rear Power Distribution Center
CAUTION!
• When installing the power distribution center cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected.
Cavity Car-
tridge Fuse 60 Amp Yellow 40 Amp Green — 40 Amp Green 30 Amp Pink —
—
Mini- Fuse
Description
—
—
— —
—
20 Amp Yellow 15 Amp Blue
Ignition Off Draw (IOD)
Integrated Power Mod- ule (IPM) — Integrated Power Mod- ule (IPM) Heated Seats - if equipped Fuel Pump
Sub Amp - if equipped
Cavity Car-
tridge Fuse —
10
11 * 12 * 13 * 1415
—
— — — — —
—
MAINTAINING YOUR VEHICLE 371
Mini- Fuse
15 Amp Blue
20 Amp Yellow — — — — 10 Amp Red
—
Description
Diagnostic Link Connec- tor (DLC)/Wireless Con- trol Module (WCM)/ Wireless Ignition Node (WIN) Power Outlet
— — — — AC Heater Control/ Cluster/Security Mod- ule - if equipped —
372 MAINTAINING YOUR VEHICLE
Cavity Car-
tridge Fuse — —
16
1718
19
20
21
22
23
24
25
26—
—
— — — — — — —
Mini- Fuse
— 20 Amp Yellow 20 Amp Yellow 10 Amp Red — — — — — — —
Description
— Cluster
Selectable Power Outlet
Stop Lights
— — — — — — —
Cavity Car-
tridge Fuse —
27
28
29
30
31
32
33
34—
—
—
— — — —
Mini- Fuse
10 Amp Red 10 Amp Red 5 Amp Orange
10 Amp Red
— — — —
Description
Occupant Restraint Con- troller (ORC) Ignition Run
Cluster/Electronic Sta- bility Program (ESP)/ Powertrain Control Module (PCM)/STOP LIGHT Switch Door Modules/Power Mirrors/Steering Con- trol Module (SCM) — — — —
Cavity Car-
tridge Fuse —
35
36
37
38
39
40
—
—
—
—
—
Mini- Fuse
5 Amp Orange
25 Amp Clear 15 Amp Blue 10 Amp Red
10 Amp Red 5 Amp Orange
Description
Antenna Module - if equipped/Power Mir- rors Hands-Free Phone - if equipped//Radio Transmission
Cargo Light/Vehicle In- formation Module - if equipped Heated Mirrors - if equipped Auto Inside Rearview Mirror/Heated Seats - if equipped/Switch Bank
Cavity Car-
tridge Fuse —
Mini- Fuse
10 Amp Red
41
42
43
44
30 Amp Pink 30 Amp Pink 20 Amp Blue
—
—
—
MAINTAINING YOUR VEHICLE 373
Description
AC Heater Control/ Headlights/Tire Pres- sure Monitoring - if equipped Front Blower Motor
Rear Window Defroster
Amplifier - if equipped/ Sunroof - if equipped
* Cavities 11, 12, and 13 contain self-resetting fuses (circuit breakers) that are only serviceable by an autho- rized dealer. The cluster and the driver seat switch are fused by the 25 Amp circuit breaker in cavity 11. The passenger seat switch is fused by the 25 Amp circuit breaker in cavity 12. The door modules, the driver power
374 MAINTAINING YOUR VEHICLE
window switch, and the passenger power window switch are fused by the 25 Amp circuit breaker in cavity 13. If you experience temporary or permanent loss of these systems, see your authorized dealer for service.
VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • Disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.
REPLACEMENT LIGHT BULBS
LIGHT BULBS — Interior Bulb Number Rear Courtesy/Reading Lights. . . . . . . . . . . . . . W5W Rear Compartment (Trunk) Light . . . . . . . . . . . . . 562
Overhead Console Reading Lights. . . . . . . . . . . . . 578
Visor Vanity Lights . . . . . . . . . . . . . . . . . . . . . A6220
Glove Box Light . . . . . . . . . . . . . . . . . . . . . . . . . 194
Door Courtesy . . . . . . . . . . . . . . . . . . . . . . . . . . 562
Shift Indicator Light . . . . . . . . . . . . . . . . . JKLE14140
Optional Door Map Pocket / Cupholder Lighting. . . . . . . . . . . . . . LED (Serviced at Authorized Dealer)NOTE: For lighted switches, see your authorized dealer for replacement instructions. All of the interior bulbs are glass wedge base or glass cartridge types. Aluminum base bulbs are not approved and should not be used for replacement.
Bulb Number
LIGHT BULBS — Exterior Low Beam Headlight – High Intensity Discharge (HID) . . . . . . . . . . . . . . . . D1S (Serviced at Authorized Dealer) High Beam Headlight. . . . . . . . . . . . . . . . . . . . . 9005
Front Park/Turn Light . . . . . . . . . . . . . . . . . . . 3157A Front Fog Light . . . . . . . . . . . . . 9145/H10 (Serviced at Authorized Dealer) Front Side Marker . . . . . . . . . . . . . . . . . . . . . . . . 168
Tail Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3057K Tail/Stop/Turn Light . . . . . . . . . . . . . . . . . . . . 3057K Rear Side Marker . . . . . . . . . . . . . . . . . . . . . . . . 168
Backup Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 921
Center High-Mount Stop Light (CHMSL) . . . . . . . . . . . . . . . . . LED (Serviced at Authorized Dealer) License. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168MAINTAINING YOUR VEHICLE 375
BULB REPLACEMENT
Low Beam Headlight, High Beam Headlight, Park/Turn Light — Models with Halogen Headlights — If Equipped See your authorized dealer for bulb replacement. Low Beam Headlight, High Beam Headlight, and Park/Turn Light — Models with High Intensity Discharge (HID) Headlights — If Equipped
HID Headlights The headlights are a type of high voltage discharge tube. High voltage can remain in the circuit even with the HEADLIGHT switch off and the key removed. Because of this, you should not attempt to service a headlight bulb yourself. If a headlight bulb fails, take your vehicle to an authorized dealer for service.
376 MAINTAINING YOUR VEHICLE
WARNING!
A transient high tension occurs at the bulb sockets of HID headlights when the headlight switch is turned ON. It may cause serious electrical shock or electro- cution if not serviced properly. See your authorized dealer for service.
NOTE: On vehicles equipped with HID headlights, when the headlights are turned on, there is a blue hue to the lights. This diminishes and becomes more white after approximately 10 seconds, as the system charges. Front/Rear Side Marker Light
1. Remove the front/rear side marker. Use a fiber stick or similar tool to gently pry the light on the outboard side to disengage the clip.
NOTE: • If a screwdriver is used, make sure a soft material is placed between the vehicle body and tool so not to scratch the paint.
2. Rotate the bulb’s socket counterclockwise, and remove the bulb and socket assembly from the housing. 3. Pull the bulb out of the socket and insert the replace- ment bulb. 4. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place. 5. Reinstall the front/rear side marker. Tail/Turn/Stop Light
1. Open the trunk. 2. Using a screwdriver, remove the tail light retainer.
MAINTAINING YOUR VEHICLE 377
3. Remove the fasteners from the back of the tail light assembly.
4. Pull back the trunk liner. 5. Remove the remaining fasteners from the back of the tail light assembly.
378 MAINTAINING YOUR VEHICLE
6. Pull the tail light assembly clear from the vehicle to access the bulbs.
7. Push the electrical connector locking tab to the side. 8. Disconnect the electrical connector. 9. Turn the appropriate bulb and socket assembly coun- terclockwise to remove it from the tail light assembly. 10. Disconnect the bulb from the socket assembly and install the replacement bulb. 11. Reinstall the bulb and socket assembly into the tail light assembly, and then turn it clockwise. 12. Reinstall the tail light assembly, fasteners, electrical connector, and trunk liner.
13. Reinstall tail light retainer.
14. Close the trunk.
MAINTAINING YOUR VEHICLE 379
Center Tail/Backup Light See your authorized dealer for bulb replacement. Center High-Mounted Stop Light (CHMSL) The CHMSL uses LED lights that are not serviceable separately. The CHMSL must be replaced as an assembly, see your authorized dealer. License Light
1. Remove the screws securing the light to the rear fascia. 2. Remove the bulb and socket assembly.
380 MAINTAINING YOUR VEHICLE
3. Disconnect the bulb from the socket assembly and install the replacement bulb.
4. Reinstall the bulb and socket assembly. 5. Reattach the light to the rear fascia, and then install the screws.
1 — License Light Bulb 2 — Socket
FLUID CAPACITIES
Fuel (Approximate) Engine Oil with Filter 6.1 Liter Engine (SAE 0W-40) Cooling System * 6.1 Liter Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level.
MAINTAINING YOUR VEHICLE 381
U.S.
19 Gallons
7 Quarts
Metric 72 Liters
6.6 Liters
15 Quarts
14.4 Liters
382 MAINTAINING YOUR VEHICLE
FLUIDS, LUBRICANTS, AND GENUINE PARTS
Engine Component Engine Coolant
Engine Oil (6.1L)
Oil Filter (6.1L) Spark Plugs (6.1L) Fuel Selection (6.1L)
Fluids, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) For best performance and maximum protection under all types of operat- ing conditions, the manufacturer only recommends full synthetic engine oils that meet the American Petroleum Institute (API) categories of SM or SM/CF, and meet the requirements of Chrysler Material Standard MS- 10725. The manufacturer recommends the use of a full synthetic engine oil, such as Mobil 1威 SAE 0W-40 or equivalent. For additional information, re- fer to the “Engine Oil Selection” and “Engine Oil Viscosity (SAE Grade)” in the “Maintenance Procedures” section of this manual. MOPAR威 Engine Oil Filter (P/N 04884899AB) or equivalent PLZTR5A-13 (Gap 0.050 in [1.27 mm]) Premium Unleaded 91 Octane Only or higher
Chassis Component Manual Transmission Automatic Transmission Brake Master Cylinder
Power Steering Reservoir
Rear Axle
MAINTAINING YOUR VEHICLE 383
Fluids, Lubricant, or Genuine Part MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. MOPAR威 Power Steering Fluid + 4, MOPAR威 ATF+4 Automatic Transmis- sion Fluid MOPAR威 Synthetic Gear Lubricant SAE 75W90 (API GL-5) or equivalent (with MOPAR威 Friction Modifier — Hypoid Gear Additive)
MAINTENANCE SCHEDULES
CONTENTS
䡵 Emission Control System Maintenance
. . . . . 386
䡵 Maintenance Schedule
▫ Required Maintenance Intervals
. . . . . . . . . . . . . . . . . 386
. . . . . . . . . 388M
386 MAINTENANCE SCHEDULES
EMISSION CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emission Control System. These, and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating conditions, such as dusty areas and very short trip driving. Inspection and service should also be done anytime a malfunction is suspected. NOTE: Maintenance, replacement, or repair of the emis- sions control devices and systems on your vehicle may be performed by any automotive repair establishment or individual using any automotive part that has been certified pursuant to U.S. EPA or in the State of Califor- nia, California Air Resources Board regulations.
Information Center
MAINTENANCE SCHEDULE The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. On Electronic Vehicle (EVIC) equipped vehicles, “Oil Change Required” will be dis- played in the EVIC and a single chime will sound, indicating that an oil change is necessary. On Non-EVIC equipped vehicles, “Change Oil” will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary. Based on engine operation conditions, the oil change indicator message will illuminate. This means that ser- vice is required for your vehicle. Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).
NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or six months, which- ever comes first.
vehicle off-road for an extended period of time.
Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by referring to the steps described under “Oil Change Re- quired” under “Electronic Vehicle Information Center (EVIC)” in Section 4 or under “Odometer/Trip Odometer” under “Instrument Cluster Descriptions” in Section 4.
MAINTENANCE SCHEDULES 387
At Each Stop for Fuel • Check the engine oil level. Refer to “Engine Oil” under • Check the windshield washer solvent and add if
“Maintenance Procedures” in Section 7.
required.
damage.
Once a Month • Check tire pressure and look for unusual wear or • Inspect the battery, and clean and tighten the terminals • Check the fluid levels of coolant reservoir, brake master cylinder, power steering, and transmission, and add as needed. • Check all lights and other electrical items for correct
as required.
operation.
Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the required maintenance intervals.
388 MAINTENANCE SCHEDULES
At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines.
CAUTION!
Failure to perform the required maintenance items may result in damage to the vehicle.
6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
MAINTENANCE SCHEDULES 389
12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner
filter, and replace if necessary.
❏ Replace the air conditioning filter. ❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the CV joints. Perform the first inspection at 12,000 miles (20 000 km) or
12 months.
❏ Inspect the exhaust system. Perform the first inspection at 12,000 miles (20 000 km) or
12 months.
❏ Inspect the manual transmission fluid (if equipped), add as necessary.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
M
390 MAINTENANCE SCHEDULES
18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires. ❏ Inspect the rear axle fluid.
24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner
filter, and replace if necessary.
❏ Replace the air conditioning filter. ❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the CV joints. ❏ Inspect the exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals, and replace if necessary. ❏ Change the manual transmission fluid (if equipped) if using your vehicle for any of the
following: Most of your driving is at sustained high speeds during hot weather, above 90°F (32°C), driving in dusty conditions, or stop and go driving.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Adjust parking brake on vehicles
equipped with four-wheel disc brakes.
36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary.
❏ Replace the air conditioning filter. ❏ Inspect the brake linings, and replace if
necessary.
❏ Inspect the rear axle fluid. ❏ Inspect the manual transmission fluid (if
equipped), add as necessary.
MAINTENANCE SCHEDULES 391
42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
Odometer Reading
Date
Odometer Reading
Date
Odometer Reading
Repair Order #
Dealer Code
Repair Order #
Dealer Code
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
M
392 MAINTENANCE SCHEDULES
48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner
filter, and replace if necessary.
❏ Replace the air conditioning filter. ❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the CV joints. ❏ Inspect the exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals, and replace if necessary. ❏ Change the rear axle fluid if using your vehicle for any of the following: police, taxi, fleet,
or frequent trailer towing.
❏ Change the manual transmission fluid (if equipped) if using your vehicle for any of the
following: Most of your driving is at sustained high speeds during hot weather, above 90°F (32°C), driving in dusty conditions, or stop and go driving.
54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires. ❏ Inspect the rear axle fluid.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the air conditioning filter. ❏ Inspect the brake linings, and replace if necessary. ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ Inspect the manual transmission fluid (if equipped), add as necessary. ❏ Change the automatic transmission fluid and filter if using your vehicle for any of the
following: police, taxi, fleet, or frequent trailer towing.
❏ Flush and replace the engine coolant at 60 months if not done at 102,000 miles
(170 000 km).
MAINTENANCE SCHEDULES 393
66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
M
394 MAINTENANCE SCHEDULES
72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner
filter, and replace if necessary.
❏ Replace the air conditioning filter. ❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the CV joints. ❏ Inspect the rear axle fluid. ❏ Inspect the exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals, and replace if necessary. ❏ Change the manual transmission fluid (if equipped) if using your vehicle for any of the
following: Most of your driving is at sustained high speeds during hot weather, above 90°F (32°C), driving in dusty conditions, or stop and go driving.
78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner
filter, and replace if necessary.
❏ Replace the air conditioning filter. ❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the manual transmission fluid (if equipped), add as necessary.
MAINTENANCE SCHEDULES 395
90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Inspect and replace the PCV Valve if
necessary.*
❏ Inspect the rear axle fluid. ❏ Adjust parking brake on vehicles
equipped with four-wheel disc brakes.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
M
396 MAINTENANCE SCHEDULES
96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner
filter, and replace if necessary.
❏ Replace the air conditioning filter. ❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the CV joints. ❏ Inspect the exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals, and replace if necessary. ❏ Change the rear axle fluid if using your vehicle for any of the following: police, taxi, fleet,
or frequent trailer towing.
❏ Change the manual transmission fluid (if equipped).
102,000 Miles (170,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires. ❏ Replace the spark plugs. ❏ Flush and replace the engine coolant if
not done at 60 months.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner
filter, and replace if necessary.
❏ Replace the air conditioning filter. ❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the rear axle fluid. ❏ Inspect the manual transmission fluid (if equipped), add as necessary.
MAINTENANCE SCHEDULES 397
114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
Repair Order #
Date
Dealer Code
Signature Authorized Chrysler Dealer
Signature Authorized Chrysler Dealer
M
398 MAINTENANCE SCHEDULES
120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the air conditioning filter. ❏ Inspect the brake linings, and replace if necessary. ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ Inspect the CV joints. ❏ Inspect the exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals, and replace if necessary. ❏ Change the automatic transmission fluid and filter. ❏ Change the manual transmission fluid (if equipped) if using your vehicle for any of the
following: Most of your driving is at sustained high speeds during hot weather, above 90°F (32°C), driving in dusty conditions, or stop and go driving.
126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil
filter.
❏ Rotate tires. ❏ Inspect the rear axle fluid.
Odometer Reading
Repair Order #
Date
Dealer Code
Odometer Reading
