2009 Dodge Caravan Owners Manual

OOOOOOOWWWWWWWWNNNNNEEERRRR’’’SSS MMMMMMAAAAANNNNNNNUUUUUUUUAAAAAALLLLLLLLLL 2222200000000000009999

VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.

WARNING!

Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive.

This manual illustrates and describes the operation of features and equipment that are either standard or op- tional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this manual that are not on this vehicle. Chrysler LLC reserves the right to make changes in design and specifications, and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previ- ously manufactured.

Copyright © 2008 Chrysler LLC

SECTION

TABLE OF CONTENTS

PAGE

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97

UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229

STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321

WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .409

MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431

MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483

IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .501

10

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511

10

INTRODUCTION

CONTENTS

䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4
䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6

䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 6
䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7

HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire. The detailed Index at the back of this Owner’s Manual contains a complete listing of all subjects. Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:

4 INTRODUCTION

INTRODUCTION This Owner’s Manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle. NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold, so that the new owner will be aware of all safety warnings. When it comes to service, remember that your authorized dealer knows your vehicle best, has the factory-trained technicians and genuine Mopar威 parts, and is interested in your satisfaction.

INTRODUCTION 5

6 INTRODUCTION

WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the Auto- mobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title.

Vehicle Identification Number

NOTE:

It is illegal to remove the VIN.

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.

INTRODUCTION 7

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS

䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12
▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . . 12
䡵 Sentry Key威 Immobilizer System . . . . . . . . . . . . 15
▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . . 16
䡵 Vehicle Security Alarm System — If Equipped . . 18
▫ Rearming Of The System . . . . . . . . . . . . . . . . 18
䡵 Illuminated Entry System — If Equipped . . . . . . 20
䡵 Remote Keyless Entry (RKE) — If Equipped . . . . 21
▫ Using The RKE Transmitter . . . . . . . . . . . . . . 21

▫ How To Use Remote Start

䡵 Remote Starting System — If Equipped . . . . . . . 28
. . . . . . . . . . . . . . . 28
䡵 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
▫ Manual Door Locks . . . . . . . . . . . . . . . . . . . . 31
▫ Power Door Locks — If Equipped . . . . . . . . . . 33
䡵 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
▫ Power Vent Windows — If Equipped . . . . . . . 37
▫ Power Windows . . . . . . . . . . . . . . . . . . . . . . 38

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

䡵 Sliding Side Door . . . . . . . . . . . . . . . . . . . . . . . 42
▫ Power Sliding Side Door — If Equipped . . . . . 43
▫ Sliding Side Door Child Protection Lock . . . . . 47
䡵 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
▫ Power Liftgate — If Equipped . . . . . . . . . . . . 50
䡵 Storage Bin Safety Warning . . . . . . . . . . . . . . . . 53
▫ Safety Warning . . . . . . . . . . . . . . . . . . . . . . . 53
䡵 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . 55
▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . 56
▫ Automatic Locking Retractors (ALR) Mode

— If Equipped. . . . . . . . . . . . . . . . . . . . . . . . 62
▫ Seat Belt Pretensioners . . . . . . . . . . . . . . . . . . 62

▫ Enhanced Seat Belt Use Reminder System

(BeltAlert威) . . . . . . . . . . . . . . . . . . . . . . . . . . 63
▫ Seat Belts And Pregnant Women . . . . . . . . . . . 64
▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . 64
▫ Supplemental Restraint System (SRS) -

Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
▫ Airbag System Components . . . . . . . . . . . . . . 66
▫ Front Seat Airbag Features . . . . . . . . . . . . . . . 66
▫ Airbag Deployment Sensors And Controls . . . . 70
▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . 76
▫ Integrated Child Booster Seat — If Equipped . . 78
▫ Integrated Child Seat — If Equipped . . . . . . . . 80
▫ Child Restraints . . . . . . . . . . . . . . . . . . . . . . . 81

䡵 Rear Seat Delete Feature (Commercial Vehicles

Only) — If Equipped. . . . . . . . . . . . . . . . . . . . . 90
▫ Restraining Infants And Small Children With

Seat Delete Feature (Commercial Vehicles Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
䡵 Engine Break-In Recommendations . . . . . . . . . . 93

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11

䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

▫ Safety Checks You Should Make Inside The

Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

▫ Periodic Safety Checks You Should Make

Outside The Vehicle . . . . . . . . . . . . . . . . . . . . 95

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Remote Keyless Entry (RKE) transmitter with integrated ignition key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the double-sided key into the ignition switch with either side up. Wireless Ignition Node (WIN) The Wireless Ignition Node (WIN) operates similarly to an ignition switch. It has four operating positions, three with detents and one that is spring-loaded. The detent positions are OFF, ACC, and ON. The START position is a spring-loaded momentary contact position. When re- leased from the START position, the switch automatically returns to the ON position.

WIN Ignition Positions

1 – OFF 2 – ACC (ACCESSORY)

3 – ON 4 – START

Integrated Ignition Key The integrated ignition key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) trans- mitter and a Valet Key, which stores in the rear of the RKE transmitter. The Valet Key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead. The Valet Key is also for locking the glove box. You can keep the Valet Key with you when valet parking. To remove the Valet Key from the RKE transmitter, slide the mechanical latch at the top of the RKE transmitter sideways with your thumb and then pull the key out with your other hand.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

Valet Key Removal

NOTE: You can insert the double-sided Valet Key into the lock cylinder with either side up.

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Tip Start Feature 1. Do not press the accelerator pedal during this process. 2. Insert the integrated ignition key into the ignition switch. 3. Turn the ignition switch to the START position and release it as soon as the starter engages. The starter motor will continue to run and will disengage automatically when the engine begins running. Ignition Key Removal Place the shift lever in PARK. Turn the ignition key to the OFF position and then remove the key. NOTE: Power window switches will also remain active for up to 90 seconds after the ignition switch has been turned OFF, depending upon the accessory delay setting. Opening the front door will cancel this feature.

WARNING!

NEVER leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seri- ously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle

CAUTION!

An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all doors when leaving the vehicle unattended.

Key-In-Ignition Reminder If you open the driver’s door with the integrated ignition key in the ignition, a chime will sound to remind you to remove the key. The Key-In-Ignition reminder only sounds NOTE: when the integrated ignition key is placed in the OFF or ACC position.

SENTRY KEY姞 IMMOBILIZER SYSTEM The Sentry Key威 Immobilizer system prevents unautho- rized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses the factory-mated Remote Keyless Entry (RKE) transmitter with integrated key and Wireless Igni- tion Node (WIN) to prevent unauthorized vehicle opera- tion. Therefore, only RKE transmitters that are pro- grammed to the vehicle can be used to start and operate

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

the vehicle. The system will shut the engine off in two seconds if an invalid RKE transmitter is used to start the engine. After turning the ignition switch to the ON position, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone used an invalid RKE transmitter to start the engine. Either of these conditions will result in the engine being shut off after two seconds. If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 sec- onds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible.

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE: • The Sentry Key威 Immobilizer system is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Exxon/Mobil Speedpass™, additional RKE transmit- ters, or any other transponder-equipped components on the same key chain will not cause a fault unless the additional part is physically held against the RKE transmitter being used to start the vehicle. Cell phones, pagers, or other Radio Frequency (RF) elec- tronics will not cause interference with this system.

All of the RKE transmitters provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys

NOTE: Only RKE transmitters that are programmed to the vehicle electronics can be used to start and operate

the vehicle. Once an RKE transmitter is programmed to a vehicle, it cannot be reprogrammed to any other vehicle.

CAUTION!

Always remove the keys from the vehicle and lock all doors when leaving the vehicle unattended.

At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of RKE trans- mitters. Duplication of RKE transmitters may be per- formed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank RKE transmitter to the vehicle electronics. A blank RKE transmitter is one that has never been programmed.

NOTE: When having the Sentry Key威 Immobilizer system serviced, bring all vehicle RKE transmitters with you to the authorized dealer. Customer Key Programming If you have two valid RKE transmitters with integrated keys, you can program new RKE transmitters to the system by performing the following steps: 1. Insert the first valid integrated key into the ignition switch and turn the ignition switch to the ON position for at least three seconds, but no longer than 15 seconds. Turn the ignition switch to the LOCK position and remove the first key. 2. Insert the second valid integrated key and turn the ignition switch to the ON position within 15 seconds. After 10 seconds, a chime will sound and the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

3. Insert a blank integrated key into the ignition switch and turn the ignition switch to the ON position within 60 seconds. After 10 seconds, a single chime will sound and the Vehicle Security Light will stop flashing, turn the ignition switch ON again for three seconds, and then turn it OFF. The new integrated key is programmed. The Remote Keyless Entry (RKE) transmitter will also be pro- grammed during this procedure. Repeat the above steps to program up to eight keys. If you do not have a programmed RKE transmitter with integrated key, contact your authorized for details.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

the time of

If a programmed key is lost, see your authorized NOTE: dealer to have all remaining keys erased from the sys- tem’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to an authorized dealer at service to be reprogrammed. General Information The Sentry Key威 system complies with FCC rules Part 15
and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undes- ired operation.

VEHICLE SECURITY ALARM SYSTEM — IF EQUIPPED The Vehicle Security Alarm system monitors the vehicle doors for unauthorized entry and the ignition switch for unauthorized operation. When the alarm is activated, the system provides both audible and visible signals. For the first three minutes, the headlights and Vehicle Security Light will flash repeatedly and the horn will sound. For an additional 15 minutes, only the headlights and Vehicle Security Light will flash. The engine will run only if a valid key is used to start the vehicle. Rearming Of The System The Vehicle Security Alarm system will rearm itself after the 15 additional minutes of headlights and Vehicle Security Light flashing, if the system has not been disabled. If the condition which initiated the alarm is still present, the system will ignore that condition and moni- tor the remaining doors and ignition.

Arming The System Remove the key from the ignition switch and either press a power door lock switch while the driver or passenger door is open, or press the LOCK button on the Remote Keyless Entry (RKE) transmitter. After all the doors are locked and closed, the Vehicle Security Light in the instrument cluster will flash rapidly to signal that the system is arming. The Vehicle Security Light in the instrument panel cluster will flash rapidly for about 16 seconds to indicate that the alarm is being set. After the alarm is set, the Vehicle Security Light will flash at a slower rate to indicate that the system is armed. If the Vehicle Security Light stays on continu- NOTE: ously during vehicle operation, have the system checked by your authorized dealer. Disarm The System Either press the UNLOCK button on the RKE transmitter or insert a valid ignition key into the ignition switch.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19

NOTE: • The driver’s door key cylinder and the liftgate button on the RKE transmitter cannot arm or disarm the system. • The system remains armed during liftgate entry. Press- ing the liftgate button will not disarm the system. If someone enters the vehicle through the liftgate and opens any door the alarm will sound. • When the system is armed, the interior power door

lock switches will not unlock the doors.

The Vehicle Security Alarm System is designed to protect your vehicle; however, you can create conditions where the system will give you a false alarm. If one of the previously described arming sequences has occurred, the system will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the system.

20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

If the Vehicle Security Alarm system is armed and the battery becomes disconnected, the system will remain armed when the battery is reconnected; the exterior lights will flash, the horn will sound. If this occurs, disarm the system. Tamper Alert If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the Vehicle Security Light will flash for 30 sec- onds. Check the vehicle for tampering. Security System Manual Override The system will not arm if you lock the doors using the manual door lock plunger.

ILLUMINATED ENTRY SYSTEM — IF EQUIPPED The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter or open the doors. This feature is only available if you have RKE. The lights will fade to off after about 30 seconds or they will immediately fade to off once the ignition switch is turned ON. NOTE: • The front courtesy overhead console, door courtesy, and liftgate lights do not turn on if the dimmer control is in the interior lights ON position (extreme top position). • The Illuminated Entry System will not operate if the dimmer control is in the extreme downward position.

REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED This system allows you to lock or unlock the doors and liftgate, and activate the Panic Alarm, optional power liftgate, left power sliding door, and right power sliding door from distances up to about 23 ft (7 m) using a hand-held radio RKE transmitter. The RKE transmitter need not be pointed at the vehicle to activate the system. If the key is in the Ignition Switch, then all NOTE: buttons on that RKE transmitter will be disabled. The buttons on the remaining transmitters will work. If the shift lever is out of PARK, all the RKE transmitter buttons are disabled for all keys. Two RKE transmitters may be supplied with the vehicle. Vehicles built without the powered options will be equipped from the factory with three-button RKE trans- mitters, and those built with power options will be equipped with up to seven-button RKE transmitters.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21

Using the RKE Transmitter Three-button RKE transmitters will provide basic UN- LOCK, LOCK and PANIC functions.

Three-Button RKE Transmitter

Seven-button RKE transmitters will provide functions that allow the same basic operation as the three-button, but may also be used to operate the power liftgate

22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

(optional), power sliding doors, Remote Start feature (optional). Some features can be programmed to the customers preferences. For example, flash headlights or sound horn on LOCK.

Seven-Button RKE Transmitter

Remote Unlock Doors and Liftgate Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door or twice to unlock all doors and liftgate. The Illuminated Entry system also turns on. Remote Key Unlock on First Press This feature lets you program the system to unlock either the driver’s side door, or all doors, on the first press of the UNLOCK button on the RKE transmitter. • For vehicles equipped with an “Electronic Vehicle Information Center (EVIC),” refer to “Remote Key Unlock,” under (Customer- Settings Programmable Features)” in Section 4.

“Personal

• For vehicles not equipped with the EVIC, the Remote Unlock feature can be enabled or disabled by perform- ing the following steps:

1. Perform this operation while standing outside the vehicle. 2. Press the LOCK button for five to ten seconds. 3. While the LOCK button is pressed, (after five seconds) press the UNLOCK button. Release both buttons. The Remote Key Unlock feature can be reactivated by repeating the above steps or by performing the steps in the optional Electronic Vehicle Information Center (EVIC), Personal Settings (Customer-Programmable Fea- tures) section of this manual. Remote Lock Doors and Liftgate Press and release the LOCK button on the RKE transmit- ter to lock all doors and liftgate. The horn will chirp once to acknowledge the signal.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23

Express Down Window Feature This feature allows you to remotely lower both front door windows at the same time. To use this feature, press and release the UNLOCK button on the RKE transmitter and then immediately press and hold the UNLOCK button until the windows lower to the level desired or until they lower completely. Sound Horn with Remote Lock This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. If desired, the Sound Horn with Remote Key Lock feature can be turned on and off by performing the following steps: 1. Perform this operation while standing outside the vehicle. 2. Press the LOCK button for five to ten seconds.

24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

(EVIC), Personal Settings

3. While the LOCK button is pressed (after five seconds) press the PANIC button. Release both buttons. The Sound Horn with Remote Key Lock feature can be reactivated by repeating the above steps or by perform- ing the steps in the optional Electronic Vehicle Informa- tion Center (Customer- Programmable Features) section of this manual. Using the Panic Alarm To turn the Panic Alarm feature on or off, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on. The Panic Alarm will stay on for three minutes unless you turn it off by pressing the PANIC button a second time, or you turn the ignition switch to the ON position.

NOTE: When you turn off the Panic Alarm by pressing the PANIC button a second time, you may have to be closer to the vehicle due to the Radio Frequency (RF) noises of the system. Open/Close Power Liftgate — If Equipped Press the LIFTGATE button twice on the RKE transmitter within five seconds to Open/Close the Power Liftgate. The liftgate will beep for three seconds and then open/ close. If the button is pushed while the liftgate is being power closed, the liftgate will reverse to the full open position. If the liftgate is locked and is not equipped with a powered liftgate, pressing the LIFTGATE button twice will result in the liftgate becoming unlocked for 30 sec- onds allowing you to manually access the liftgate area. The power liftgate may also be opened and closed by pressing the LIFTGATE button located on the overhead console.

If equipped with a rear interior switch on the left rear pillar, pushing this switch once will close the liftgate only. The liftgate cannot be opened from this switch. Open/Close Power Left Power Sliding Door — If Equipped Press the LEFT Power Sliding Door button twice on the RKE transmitter within five seconds to Open/Close Power Left Power Sliding Door. If the button on the RKE transmitter is pushed while the door is being power- closed, the door will reverse to the full open position. Open/Close Power Right Power Sliding Door — If Equipped Press the RIGHT Power Sliding Door button twice on the RKE transmitter within five seconds to Open/Close Power Right Power Sliding Door. If the button on the RKE transmitter is pushed while the door is being power-closed, the door will reverse to the full open position.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25

Turn Off Flash Lights with RKE Lock — If Equipped If desired, the Flash Lights with RKE Lock feature can be turned on and off by performing the following steps: 1. Perform this operation while standing outside the vehicle. 2. Press the UNLOCK button on the RKE transmitter for five to ten seconds. 3. While the UNLOCK button on the RKE transmitter is pressed, (after five seconds) press the LOCK button. Release both buttons. The Flash Lights with Remote Key Lock feature can be reactivated by repeating the above steps or by perform- ing the steps in Section 4, “Electronic Vehicle Information Center (Customer- Programmable Features),” on vehicles so equipped.

Personal

Settings

(EVIC),

26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

The table below explains the Lamp Flash options.

Function

Number of

Flashes

Which Turn Signal Lamps All Left Side All Left Side Right Side All

Lock Unlock 1st Press Unlock All Doors Left Side Right Side Liftgate Programming Additional RKE Transmitters Refer to Sentry Key威 Immobilizer System “Customer Key Programming.” If you do not have a programmed RKE transmitter, contact your authorized dealer for details.

Replacing the RKE Transmitter Battery The recommended replacement battery is one CR2032
battery. NOTE: • Perchlorate Material — special handling may apply. See: www.dtsc.ca.gov/hazardouswaste/perchlorate. • Do not touch the battery terminals that are on the back

housing or the printed circuit board.

1. Battery access is through a door located on the back of the RKE transmitter. Insert a small, flat-bladed screw- driver into the slot and gently pry open the access door.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27

3. Reposition the access door panel over the battery opening and snap into place. General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.

If your RKE transmitter fails to operate from a normal distance, check for these two conditions. 1. A weak battery in the RKE transmitter. The expected life of the battery is approximately three years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.

RKE Transmitter Battery Replacement

1– Battery Access Door

2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch the battery, clean it with rubbing alcohol.

28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

REMOTE STARTING SYSTEM — IF EQUIPPED The Remote Starting system conveniently starts the en- gine from outside the vehicle by using the Remote Keyless Entry (RKE) transmitter while maintaining the Vehicle Security Alarm system. The Remote Starting system has a targeted range of 328 ft (100 m). In order to Remote Start your vehicle, the hood, liftgate, and all the doors must be closed and the shift lever in PARK. NOTE: The Remote Starting system is available only on vehicles with automatic transaxles. How to Use Remote Start All of the following conditions must be met before the engine will Remote Start: • Shift lever in PARK • Doors closed • Hood closed

• Trunk closed • Hazard switch off • Brake switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level, and • RKE PANIC button not pressed. To Enter Remote Start Mode

Press and release the REMOTE START button on the RKE transmitter twice within five sec- onds. The parking lights will flash and the horn will sound twice (if programmed). Then, the engine will start and the vehicle will remain in the Remote Start mode for a 15-minute cycle.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29

• For security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is in the Remote Start mode. • The engine can be started two consecutive 15-minute cycles with the RKE transmitter. However, the ignition switch must be turned to the ON position before you can repeat the start sequence.

To Enter the Vehicle After Remote Start To enter the vehicle while the engine is running during a Remote Start, you must first unlock the vehicle using the UNLOCK button on the transmitter. After the vehicle is unlocked, you can enter the vehicle, insert the key into the ignition switch and move it to the ON position, otherwise the engine will shut off at the end of 15- minute cycle.

Remote Starting Button

NOTE: • If your power door locks were unlocked, Remote Start • The park lights will turn on and remain on during

will automatically lock the doors.

Remote Start mode.

30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

To Exit Remote Start Mode and Drive the Vehicle Before the end of the 15-minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped). Then, prior to the end of the 15-minute cycle, insert the key into the ignition switch and turn the switch to the ON position. NOTE: • The ignition switch must be in the ON position in • For vehicles equipped with the Electronic Vehicle Information Center (EVIC), the message “Insert Key/ Turn to ON” will flash in the EVIC until you insert the key. Once inserted, the message “Turn to ON” will flash in the EVIC until you turn the key to ON.

order to drive the vehicle.

Cancel Remote Start Remote Starting will also cancel if any of the following occur:

• The engine stalls or engine speed exceeds 2500 rpm • Any engine warning lights come on • The hood is opened • The hazard switch is pressed • The shift lever is moved out of PARK • The brake pedal is pressed • The engine is allowed to run for the entire 15-minute

cycle

To Turn Off the Engine While in Remote Start Mode Press and release the REMOTE START button one time. NOTE: To avoid inadvertent shutdowns while in the Remote Start Mode, the system will not allow the Remote Start button to shutdown the engine for two seconds after receiving a valid Remote Start request.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31

When to Reset Remote Start The vehicle can be started remotely up to a maximum of two times. The vehicle is also allowed a maximum of one failed start, where the Remote Starting sequence was initiated but the engine stopped cranking without start- ing. After either of these conditions, or if the Vehicle Security Alarm system is alarming, or if the PANIC button was pressed, the vehicle must be reset by inserting a valid key into the ignition switch and rotating the key to the ON position, and then rotating the key back to the LOCK/OFF position.

DOOR LOCKS

Manual Door Lock

Manual Door Locks Lock the doors by pushing down on the lock plungers on each door trim panel.

If the lock plunger is down when you shut the door, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door.

32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

• For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition switch, and lock your vehicle. Do not leave unattended children in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe per- sonal injuries and death.

Sliding Door Lock

Power Door Locks — If Equipped A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33

If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate. This prevents you from acciden- tally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate. A chime will sound if the key is in the ignition switch and a door is open, as a reminder to remove the key.

Driver Power Door Lock Switch

1 - Unlock

2 - Lock

34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Front Passenger Power Door Lock Switch

1 - Window Open/Close 2 - Doors Lock

3 - Doors Unlock

If you press the power door lock switch while the sliding door is open, the sliding door will lock.

Lock Doors Automatically — If Equipped If the Lock Doors Automatically feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The Lock Doors Automatically feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: • On vehicles equipped with the optional Electronic Vehicle Information Center (EVIC), refer to ⬙Personal Settings (Customer-Programmable Features)⬙ in the EVIC section of this manual. • On vehicles not equipped with the optional EVIC

perform the following steps:

1. Enter your vehicle and close all doors. 2. Fasten your seat belt. (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure.)

3. Place the key into the ignition. 4. Within 15 seconds, cycle the ignition key from the LOCK position to the ON/RUN position a minimum of four times, ending in the LOCK position (do not start the engine). 5. Within 30 seconds, press the driver’s door lock switch in the LOCK direction. 6. A single chime will be heard to indicate the feature has been disabled. 7. To reactivate this feature, repeat the above steps. 8. If a chime is not heard, the program mode was canceled before the feature could be disabled. If neces- sary, repeat the above procedure.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35

The Lock Doors Automatically at 15 mph (24 km/h) feature can be reactivated by repeating the above men- tioned procedure or by performing the procedure in the EVIC (if equipped), Personal Settings (Customer- Programmable Features) section. Unlock Doors Automatically On Exit — If Equipped The Unlock Doors Automatically On Exit feature unlocks all of the doors of the vehicle when any door is opened. This will occur only after the shift lever has been shifted into the PARK position, after the vehicle has been driven (the shift lever has been shifted out of PARK and all doors closed). The Unlock Doors Automatically On Exit feature will not operate if there is any manual operation of the power door locks (lock or unlock).

36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

The Unlock Doors Automatically On Exit feature can be enabled or disabled by performing the following proce- dure: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt. (Fastening the seat belt will cancel any chimes that may be confusing during this programming procedure.) 3. Insert the key into the ignition switch. 4. Within 15 seconds, cycle the ignition key from the LOCK position to the ON/RUN position a minimum of four times ending in the LOCK position (do not start the engine). 5. Within 30 seconds, press the driver’s door lock switch in the UNLOCK direction. 6. A single chime will sound to indicate the feature has been changed.

7. To reactivate this feature, repeat the above steps. 8. If a chime is not heard, the program mode was canceled before the feature could be changed. If neces- sary, repeat the above procedure. The Unlock Doors Automatically On Exit feature can be reactivated by repeating the above mentioned procedure or by performing the procedure in the EVIC, Customer Programmable Features section on vehicles so equipped. NOTE: Use the Lock Doors Automatically at 15 mph (24 km/h) and Unlock Doors Automatically On Exit features in accordance with local laws. Remote Power Unlock On First Press — If Equipped The Remote Power Unlock On First Press feature lets you program the system to unlock either the driver’s side door or all doors on the first press of the UNLOCK button on the transmitter.

The Remote Power Unlock On First Press feature can be enabled or disabled by performing the following proce- dure: 1. Perform this operation while standing outside the vehicle. 2. Press the LOCK button for five to ten seconds. 3. While the LOCK button is pressed, (after five seconds) press the UNLOCK button. Release both buttons. The Remote Power Unlock On First Press feature can be reactivated by repeating the above procedure or by performing the procedure in Section Four, “Electronic Vehicle Information Center (EVIC), Personal Settings (Customer-Programmable Features)” on vehicles so equipped. For other power lock features, refer to “Remote Keyless Entry (RKE) Transmitter” earlier in this section.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37

WINDOWS

Power Vent Windows — If Equipped Switches on the driver’s door trim panel let the driver operate the two vent windows from the driver’s seat.

Power Vent Window Switches

1 – Open

2 – Close

38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Power Windows You can control either the front or rear windows using switches located on the driver’s door trim panel. The switches will operate only when the ignition switch is in the ON or ACC position and during power accessory delay.

Driver’s Power Window Switches

1 – Left Rear 2 – Right Rear

3 – Left Front 4 – Right Front

NOTE: Power Window switches will also remain active for up to 90 seconds after the ignition switch has been turned OFF, depending upon the accessory delay setting. Opening the front door will cancel this feature.

Power Window Lockout Switch — If Equipped The driver may lock out all power windows by depressing the bar switch just below the power window switches.

and locks and unlocks all doors. The switch will operate only when the ignition switch is in the ON or ACC position and during power accessory delay.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39

Power Window Lockout Switch Front Passenger Power Window Switch There is a single switch on the front passenger’s door trim panel which operates the passenger door window

Front Passenger Power Window Switches

1 - Window Open/Close 2 - Doors Lock

3 - Doors Unlock

40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Sliding Side Door Power Window Switch Second row passengers may power the sliding door window by a single switch on the door handle assembly. The switches will operate only when the ignition switch is in the ON or ACC position.

Sliding Door Power Window Switch

NOTE: Please note that the sliding door windows do not fully recline, stopping several inches above the window sill. Auto Down Feature — If Equipped The front window switches may be equipped with an auto down feature. Press the window switch past the detent, release, and the window will go down automati- cally. To open the window part way, press the window switch part way and release it when you want the window to stop. The power window switches remain active for up to 90 seconds (depending on the accessory delay setting) after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature.

Auto Up Feature With Anti–Pinch Protection — If Equipped The front Driver switch may be equipped with an Auto Up feature. Lift the window switch to the second detent, release, and the window will go up automatically. To stop the window from going all the way up during the Auto Up operation, push down on the switch briefly. To close the window part way, lift the window switch to the first detent and release when you want the window to stop. NOTE: • If the window runs into any obstacle during auto- closure, it will reverse direction and then stop. Remove the obstacle and use the window switch again to close the window.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41

• Any impact due to rough road conditions may trigger the auto reverse function unexpectedly during auto- closure. If this happens, pull the switch lightly to the first detent and hold to close window manually.

WARNING!

There is no anti-pinch protection when the window is almost closed. To avoid personal injury be sure to clear your arms, hands, fingers and all objects from the window path before closing.

Auto Up Reset — If Equipped To reactivate the Auto Up feature, perform the following steps after vehicle power is restored: 1. Pull the window switch up to close the window completely and continue to hold the switch up for an additional two seconds after the window is closed.

42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting.

SLIDING SIDE DOOR The sliding door may be opened from the inside or the outside. Pull outward on exterior handle to open the sliding door. The sliding door inside handle functions by rocking forward and back. Rocking the handle back- wards opens the door and rocking forward releases the hold open latch in order to close the door. To keep your door operating properly, observe the fol- lowing guidelines: • Always open the door smoothly. • Avoid high impacts against the door stop when open- ing the door. This is very important when your vehicle is parked on an incline as the door will slide faster in the downhill direction.

• There is a hold-open latch that is activated when the sliding door is fully opened. This latch will keep your sliding door open on any incline. To close the sliding door after the hold-open latch is activated, you must rock the inside handle forward or pull outward on the outside handle.

Always make sure that the sliding door is fully latched anytime the vehicle is in motion. NOTE: The left side sliding door cannot be opened manually while the fuel door is open. This feature operates only when the sliding door is fully closed prior to opening the fuel door. Power Sliding Side Door — If Equipped The power sliding door may be opened or closed manu- ally or by using the buttons on the RKE transmitter,

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43

overhead console switch, or rear door switch. Pulling the inside or outside power sliding door handle will also power open or close the power sliding door. Press the button on the RKE transmitter twice within five seconds to open a power sliding door. When the door is fully open, pressing the button twice within five seconds a second time will close the door. There are power sliding side door switches located on the trim panel just in front of the power sliding door for the rear seat passengers and in the overhead console for the driver and passengers. Pressing the switch once will open the power sliding door. When the door is fully open pressing the switch a second time will close the door. NOTE: The power sliding side door must be unlocked before the power sliding door switches will operate.

44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

1 — Heated Seat 2 — Power Window 3 — Manual Lock

Power Sliding Door

4 — Door Handle 5 — Power Sliding Door

If the inside or outside door handles are used while the power sliding side door is activated, the power sliding door feature will be canceled.

To avoid unintentional operation of the power sliding doors from the rear seats, press the power sliding door master lock button, located in the overhead console, to disable the switches and handles for the rear seat passen- gers. NOTE: • The power sliding side door switches will not open if the shift lever is in gear or the vehicle speed is above 0 mph (0 km/h). To close the power sliding door with the shift lever in gear and vehicle speed at 0 mph (0 km/h), the brake must be pressed • If anything obstructs the power sliding side door while it is closing or opening, the door will automati- cally reverse to the closed or open position, provided it meets sufficient resistance. • If the power sliding side door is not in the full open or close position, it will fully open when a power sliding

door switch is pressed. To close the door, wait until it is fully open and then press the switch again. • The power sliding side door switches will not operate if the shift lever is in gear or the vehicle speed is above 0 mph (0 km/h). • If the power sliding door encounters multiple obstruc- tions within the same cycle, the system will automati- cally stop and must be opened or closed manually.

WARNING!

You, or others, could be injured if caught in the path of the sliding door. Make sure the door path is clear before closing the door.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45

Power Sliding Side Door Open Flash The left and right exterior hazard lights will flash for 12 seconds when either sliding door is opened. This will alert other drivers in the area that passenger(s) could be entering or exiting the vehicle. The Sliding Side Door Open Flash can be enabled or disabled by performing the following procedure: 1. Place the key in the ignition switch. 2. Cycle the ignition switch ON/OFF four times ending in the ON position (do not start the engine). 3. Within 10 seconds of the final cycle, press the HAZ- ARD switch. 4. A single chime will sound to signify that you have successfully completed the programming. You can turn the feature back on by repeating the above mentioned procedure.

46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Power Sliding Side Door Master Lock Switch The power sliding side door may also be opened by pressing the switches on the overhead console or the switch located on the trim panel just in front of the sliding door. When the power sliding door master lock switch is in the ON position, the power sliding side door may not be opened or closed by pressing the switch located on the trim panel just in front of the sliding door or activating the inside power sliding door handle. To provide a safer environment for small children riding in the rear seats, the sliding door locks may be overrid- den by pressing the ON side of the Master Lock Out Switch located in the front overhead console.

Overhead Console Power Sliding Door Master Switch 1 — Left Door 2 — Liftgate

3 — Right Door 4 — Master Lock

Sliding Side Door Child Protection Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a Child Protection Door Lock system. NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. To Engage the Child Protection Door Lock 1. Open the sliding side door. 2. Slide the Child Protection Door Lock control inward (toward the vehicle) to engage the Child Protection Door Lock.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47

Child Protection Door Lock

3. Repeat Steps 1 and 2 on the opposite sliding door. NOTE: • After engaging the Child Protection Door Lock, al- ways test the door from the inside to make certain it is in the desired position.

48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

• When the Child Protection Door Lock system is en- gaged, (even if the inside door lock is in the unlocked position) the door can be opened only by using the outside door handle, the RKE transmitter, the switches on the overhead console or the switches located on the trim panel just in front of the power sliding door. • The power sliding side door will operate from the switches located on the trim panel just in front of the power sliding door, regardless of the Child Protection Door Lock lever position. To avoid unintentional operation of the power sliding door from the rear seats, press the ”ON” Master Lock Out Switch lo- cated in the front overhead console, next to the driver.

WARNING!

Avoid trapping anyone in the vehicle in a collision. Remember that the sliding doors can only be opened from the outside door handle or the switches located on the trim panel just in front of the power sliding door when the Child Protection Door Locks are engaged.

To Disengage the Child Protection Door Lock 1. Open the sliding side door. 2. Slide the Child Protection Door Lock control outward (away from the vehicle) to disengage the Child Protection Door Lock. 3. Repeat Steps 1 and 2 on the opposite sliding door (if equipped).

NOTE: • After setting the Child Protection Door Lock system, always test the door from the inside to make certain it is in the desired position. • The power sliding side door switches will not operate if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h). • The power sliding door will operate from the outside door handle, the RKE transmitter, the switches on the overhead console, or the switches located on the trim panel just in front of the power sliding door when the shift lever is in PARK, regardless of the child lock lever position.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49

LIFTGATE On vehicles equipped with power locks, the liftgate can be unlocked using the Remote Keyless Entry (RKE) transmitter button, or by activating the power door lock switches located on the front doors. To open the liftgate, depress the liftgate release handle located on the underside of the license plate bar and pull the liftgate open with one fluid motion.

50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the Remote Keyless Entry (RKE) transmit- ter. Press the button on the transmitter twice within five seconds, to open the power liftgate. When the liftgate is fully open, pressing the button twice within five seconds, a second time, will close the liftgate. The power liftgate may also be opened and closed by pressing the button located on the overhead console.

Liftgate Handle Location

If the liftgate is locked and is not equipped with the power liftgate feature, pressing the button on the RKE transmitter will result in the liftgate becoming unlocked for 30 seconds allowing you to manually access the liftgate area.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51

Overhead Console Master Power Switch

Liftgate Rear Switch

1 — Left Door 2 — Liftgate

3 — Right Door 4 — Master Lock

The power liftgate may be closed by pressing the button, located in the upper left trim in the liftgate opening. Pushing once will only close the liftgate. This button cannot be used to open the liftgate.

When the RKE transmitter button is pressed and the Flash Lights feature is enabled, the tail lights will flash to signal that the liftgate is opening or closing.

52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away.

NOTE: • If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically reverse to the closed or open position, provided it meets sufficient resistance. • There are also pinch sensors attached to the side of the liftgate opening. Light pressure anywhere along these strips will cause the liftgate to return to the open position.

• The power liftgate must be in the full open or close positions for any of the buttons to operate. If the liftgate is not in the full open or close positions, it must be opened or closed manually. • If the liftgate release button is activated while the power liftgate is closing, the liftgate will reverse to the full open position. • The power liftgate buttons will not operate if the shift lever is in gear or the vehicle speed is above 0 mph (0 km/h). • The power liftgate will not operate in temperatures below ⫺12°F (⫺24°C) or temperatures above 143°F (62°C). Be sure to remove any buildup of snow or ice from the liftgate before pressing any of the power liftgate buttons.

• If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually.

WARNING!

• Driving with the liftgate open can allow poison- ous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode.

Gas props support the liftgate in the open position. However, because the gas pressure drops with tempera- ture, it may be necessary to assist the props when opening the liftgate in cold weather.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53

STORAGE BIN SAFETY WARNING

Safety Warning

WARNING!

vehicle is unattended.

• Always close the storage bin covers when your • Do not allow children to have access to the second row seat storage bins. Once in the storage bin, young children may not be able to escape. If trapped in the storage bin, children can die from suffocation or heat stroke. • In an accident, serious injury could result if the seat storage bin covers are not properly latched. • Do not drive the vehicle with the storage bin • Keep the storage bin covers closed and latched

covers open.

while the vehicle is in motion.

(Continued)

54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING! (Continued)

• Do not operate the storage bin covers while the • Do not use a storage bin latch as a tie down.

vehicle is in motion.

CAUTION!

The storage bin cover must be flat and locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.

Seat Storage Bin Cover Emergency Release Lever — If Equipped As a security measure, your vehicle may be built with a Storage Bin Cover Emergency Release is built into the storage bin cover latching mechanism.

Storage Bin Cover Emergency Release Lever

In the event of an individual being locked inside NOTE: the storage bin, the storage bin cover can be opened from inside of the bin by pulling on the glow-in-the-dark lever attached to the storage bin cover latching mechanism.

positions

seat belts

OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems: • Three-point lap and shoulder belts for all seating • Pretensioning and load-limiting retractors for the front • Advanced multistage driver and new active-vent front • Supplemental side airbags that span the front, second, and third row seating for the driver and passengers seated next to a window. • An energy-absorbing steering column and steering • Knee bolsters/blockers for front seat occupants

passenger airbags

wheel

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55

• Front seat belt retractors incorporate pretensioners to enhance occupant protection by managing occupant energy during an impact event. • All seat belt systems (except the driver’s, Swivel n’ Go, and third row center position) include Automatic Locking Retractors (ALRs), which lock the seat belt webbing into position by extending the belt all the way out and then adjusting the belt to the desired length to restrain a child seat or secure a large item in a seat.

If you will be carrying children too small for adult-size seat belts, your seat belts or the Lower Anchors and Tether for CHildren (LATCH) feature also can be used to hold infant and child restraint systems. NOTE: The front airbags have a multistage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity.

56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible.

WARNING!

In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly.

Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street.

Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seats in your vehicle are equipped with lap/shoulder belts. The belt webbing in the retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out.

WARNING!

• It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. (Continued)

using a seat belt properly.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57

WARNING! (Continued)

• Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your pas- sengers safe, too. • Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or lap belt for more than one person, no matter what their size.

Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat.

58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.

Pulling Out Belt and Latch Plate

WARNING!

• A belt that is worn under your arm is very danger- ous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together.

3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59

WARNING!

• A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.

Inserting Latch Plate into Buckle

60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.

Removing Slack from Belt

WARNING!

• A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your authorized dealer and have it fixed.

5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully.

WARNING!

A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).

Third Row Center Shoulder Belt Instructions The shoulder belt for the third row center seat is located in the headliner slightly behind the third row seat. Pull the strap down and secure the small latch plate of the lap belt into the small buckle until you hear a “click”. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. When the belt

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61

is long enough to fit, insert the large latch plate into the buckle until you hear a “click.” The retractor should withdraw any slack in the belt. To release the small latch plate, position the end of the large latch plate against the red button on the small latch plate and push upward. Reinstall the latch plates into the headliner. Adjustable Upper Shoulder Belt Anchorage In the front seats and the second row outboard seats, the shoulder belt anchorage can be adjusted upward or downward to help position the belt away from your neck. The upper anchorage can be adjusted upward by pushing anywhere on the anchorage. To move the an- chorage downward, squeeze the actuation buttons while simultaneously pushing down on the anchorage assem- bly.

62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Automatic Locking Retractors (ALR) Mode — If Equipped In this mode, the shoulder belt is automatically pre- locked. The belt will still retract to remove any slack in the shoulder belt. The Automatic Locking mode is avail- able on all passenger-seating positions with a combina- tion lap/shoulder belt. When to Use the Automatic Locking Mode Use The Automatic Locking mode anytime a child safety seat is installed in a passenger seating position. Children 12 years old and younger should be properly restrained in the rear seat whenever possible.

How to Use the Automatic Locking Mode 1. Buckle the combination lap/shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the Automatic Locking mode. How to Disengage the Automatic Locking Mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the Automatic Locking mode and activate the Vehicle Sensitive (Emer- gency) Locking mode. Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt

by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints. NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the Occupant Re- straint Controller (ORC). Like the front airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced. Enhanced Seat Belt Use Reminder System (BeltAlert姞) If the occupied driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), BeltAlert威 will alert the driver to buckle the seat belt. The driver should also instruct all other occupants to buckle their seat belts.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63

Once the warning is triggered, BeltAlert威 will continue to chime and flash the Seat Belt Warning Light for 96 sec- onds or until the driver’s seat belt is buckled. BeltAlert威 will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). BeltAlert威 Programming BeltAlert威 can be enabled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. Chrysler LLC does not recommend deactivating BeltAlert威. 1. With all doors closed and the ignition switch in any position except ON or START, buckle the driver’s seat belt.

64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

2. Turn the ignition switch to the ON position (engine does not need to be running), and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of turning the ignition switch to the ON/RUN position, unbuckle and then re-buckle the driver’s seat belt at least three times within 60 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. 4. Turn the ignition switch to the OFF position. A single chime will sound to signify that you have successfully completed the programming. BeltAlert威 can be reactivated by repeating this procedure. NOTE: Although BeltAlert威 has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s seat belt remains unbuckled or unretracted.

Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the ex- tender and stow it.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65

The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size. This vehicle may also be equipped with Supplemental Seat Side Airbag Inflatable Curtains (SABIC) to protect the driver, front, and rear passengers sitting next to a window. If the vehicle is equipped with SABIC airbags, they are located above the side windows and their covers are also labeled: SRS AIRBAG. NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment.

WARNING!

Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.

Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers. NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment.

66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Airbag System Components The airbag system consists of the following: • Occupant Restraint Controller (ORC) • Airbag Warning Light • Driver Airbag • Front Passenger Airbag • Front and Side Impact Sensors • Steering Wheel and Column • Instrument Panel • Seat Belt Warning Light • Knee Impact Bolster • Front Seat Belt Retractor Pretensioners • Front Seat Track Position Sensors

• Supplemental Seat Side Airbag Inflatable Curtains

(SABIC) (if equipped)

Front Seat Airbag Features The front airbag system has dual-stage driver and front passenger airbags. This system provides output appro- priate to the level of crash severity as determined by the Occupant Restraint Controller (ORC) and the impact sensors at the front of the car. The first stage inflator is triggered immediately during an impact that requires airbag deployment. The timing of the second stage determines whether the output force is low, medium, or high. If a low output is sufficient to meet the need, the second stage is expended later in the crash event.

Driver Airbag Special Features Driver airbag deployment and force level is controlled by the driver’s seat position as well as impact severity. Use of special inflators result in a very compact driver’s side airbag. In addition to the small size, the inflating gases exit through strategically placed vents, which direct the gas away from the occupant. Front Passenger Airbag Special Features A new active venting front passenger airbag is designed to reduce the risk of occupants who may be out of position by the use of active vents positioned on each side of the airbag.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67

WARNING!

• Do not put anything on or around the airbag covers or attempt to open them manually. You may damage the airbags and you could be injured because the airbag inflation capability may be compromised. The protective covers for the airbag cushions are designed to open only when the airbags are inflating. • Do not use accessory seat covers or place objects between you and the side airbags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury.

68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC Airbags offer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries. The curtains deploy down- ward, covering both windows on the impact side. NOTE: • Should a vehicle rollover occur, the SABIC curtains on • Airbag covers may not be obvious in the interior trim;

both sides of the vehicle are deployed.

but they will open to allow airbag deployment.

The system includes sensors adjacent to both front and rear seat occupants that are calibrated to deploy during an impact severe enough to require airbag occupant protection.

WARNING!

If your vehicle is equipped with left and right Side Airbag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC. The area where the side curtain airbag is located should remain free from any obstructions.

Airbags inflate in moderate to high speed impacts. Along with seat belts and pretensioners, front airbags work with the knee bolsters to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions. If your vehicle is equipped, the side airbag on the crash side of the vehicle is triggered in moderate to severe side collisions. In certain types of

collisions, both the front and side airbags may be trig- gered. However, even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. Children 12 years old and younger should always ride buckled up in a rear seat. Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deploy- ment can cause severe injury or death to infants in that position. Children that are not big enough to wear the vehicle seat belt properly (see Section on Child Restraints should be secured in the rear seat in child restraints or belt- positioning booster seats. Older children who do not use child restraints or belt-positioning booster seats should

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69

ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint. Refer to the section on Child Restraints. You should read the instructions provided with your child restraint to make sure that you are using it properly. All occupants should wear their lap and shoulder belts properly. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. If your vehicle has side airbags, do not lean against the door, airbags will inflate forcefully into the space be- tween you and the door.

70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under ⬙If You Need Assistance⬙ in Section 9 of this manual.

WARNING!

• Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during front airbag deployment could cause serious injury. Airbags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel.

(Continued)

WARNING! (Continued)

• Side airbags also need room to inflate. Do not lean against the door. Sit upright in the center of the seat.

Airbag Deployment Sensors and Controls

Occupant Restraint Controller (ORC) The ORC is part of a Federally regulated safety system required for this vehicle. The ORC determines if a frontal or side collision is severe enough to require the airbags to inflate. Based on the impact sensors signals, a central electronic ORC deploys the front airbags, side inflatable airbag curtains, side seat thorax airbags, and front seat belt pretensioners as re- quired for each type of impact. The ORC monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START

or ON position. These include all of the components listed above except the steering wheel and column, instrument panel, and seat belt reminder light. If the key is in the OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate. The ORC contains a backup power supply system that will deploy the airbags even if the battery loses power or it becomes disconnected prior to deployment.

Also, the ORC turns on the Airbag Warning Light in the instrument panel for approxi- mately four to six seconds for a self-check when the ignition is first turned on. After the self-check, the Airbag Warning Light will turn off. If the ORC detects a malfunction in any part of the system, it turns on the Airbag Warning Light, either momentarily or continuously. A single chime will sound if the light comes on again after initial start up.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71

It also includes diagnostics that will illuminate the instru- ment cluster Airbag Warning Light if a malfunction is noted. The diagnostics also record the nature of the malfunction.

WARNING!

Ignoring the Airbag Warning Light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.

Front and Side Impact Sensors Impact Sensors trigger airbag deployment in front and side impacts, and aid the ORC in determining appropri- ate response to impact events. Additional sensors in the ORC determine the level of airbag deployment and provide verification.

72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Acceleration Sensors Acceleration Sensors trigger airbag deployment based on dramatic acceleration change of the vehicle. Pressure Sensors Pressure Sensors trigger airbag deployment based on door cavity pressure changes. Rollover Sensors Rollover Sensors trigger airbag deployment in the event of vehicle rollover and aid the ORC in deploying Side Airbag Inflatable Curtains (SABIC) for rollover events. Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped The ORC deploys the SABIC during a collision with other vehicles and during collisions where the impact is confined to a particular area of the vehicle, such as, collisions with poles, trees or similar objects. In these events, the ORC will deploy the SABIC only on the impact side of the vehicle.

NOTE: The ORC will also detect and protect for rollover when equipped with SABIC airbags. In a rollover the SABIC airbags will deploy on both sides of the vehicle. Enhanced Accident Response System In the event of an impact causing airbag deployment, and the vehicle communication network intact, and the power intact, the Enhanced Accident Response System performs the following functions: • Cuts off fuel to the engine. • Flashes hazard lights. • Turns on the interior lights, which remain on as long as the battery has power or until the ignition key is removed.

• Unlocks the doors automatically.

If A Deployment Occurs The airbag systems are designed to deploy when the Occupant Restraint Controller (ORC) detects a moderate- to-severe collision, to help restrain the driver, front passenger and rear passengers, and then immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73

They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instruc- tions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you.

74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!

Maintaining Your Airbag System

Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retractor assembly replaced by an authorized dealer as soon as possible. Also, have the Occupant Restraint Controller (ORC) system serviced as well.

WARNING!

• Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or add aftermarket side steps or running boards. • It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has an airbag system. (Continued)

WARNING! (Continued)

• Do not attempt to modify any part of your ad- vanced airbag system. The airbag may inflate accidentally or may not function properly if modi- fications are made. Take your vehicle to an autho- rized dealer for any advanced airbag system ser- vice. If your seat, including your trim cover and cushion, needs to be serviced in any way (includ- ing removal or loosening/tightening of seat attach- ment bolts), take the vehicle to your authorized dealer. Only manufacturer approved seat accesso- ries may be used. If it is necessary to modify an advanced airbag system for persons with disabili- ties, contact your authorized dealer.

NOTE: Perchlorate Material — special handling may ap- ply. See: www.dtsc.ca.gov/hazardouswaste/perchlorate.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75

Airbag Warning Light

You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be mainte- nance free, if any of the following occurs, have an authorized dealer service the system immediately. • The Airbag Warning Light does not come on for approximately four to six seconds when the ignition switch is first turned ON. • The light remains on after the approximate four to • The light comes on and remains on while driving. If the speedometer, tachometer, or any engine NOTE: related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The airbags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label

six-second interval.

76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good. Event Data Recorder (EDR) In the event of an accident, your vehicle is designed to record up to approximately five seconds of specific vehicle data parameters (see the following list) in an event data recorder prior to the moment of airbag de- ployment, or near deployment, and up to a quarter- second of high-speed deceleration data during and/or after airbag deployment. EDR data are ONLY recorded if an airbag deploys, or nearly deploys, and are otherwise unavailable. NOTE: • A near-deployment event occurs when the airbag sensor detects severe vehicle deceleration usually in- dicative of a crash, but not severe enough to warrant airbag deployment.

• Under certain circumstances, EDR data may not be

recorded (e.g., loss of battery power).

In conjunction with other data gathered during a com- plete accident investigation, the electronic data may be used by the manufacturer and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance. In addition to crash investigations initiated by the manufac- turer, such investigations may be requested by custom- ers, insurance carriers, government officials, and profes- sional crash researchers, such as those associated with universities, and with hospital and insurance organiza- tions. In the event that an investigation is undertaken by the manufacturer (regardless of initiative), the company or