2009 Dodge Caravan Owners Manual

• A side storage pocket that will accommodate a phone

or handheld game

Swivel ’n Go Seating Features

1 — Moveable Armrest 2 — Seatback Release 3 — Swivel Release

4 — Fore-Aft Adjustment 5 — Seat Release

To swivel the seat: Pull the lower handle on the outboard side of the seat and push the side of the seatback to begin

rotation. Once the seat begins to rotate, the handle may be released. The seat locks in position once reaching the forward or rearward positions only.

Swivel Release

Seatbacks fold forward on an angle, not flat. This allows the seats to swivel when the seatbacks are folded.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155

WARNING!

Failure to comply with the following conditions could result in serious injury or even death. • NEVER place any child seat or infant carrier in the Swivel ’n Go seat while it is in the rearward facing position. • The swivel seat should be locked in the forward position when using any child seat or infant carriers, with the vehicle in motion.

WARNING!

Failure to comply with the following conditions could result in serious injury or even death.

(Continued)

156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING! (Continued)

• Occupants riding in Swivel ’n Go seating must be wearing their seat belt and the seat must be locked in either the forward-facing or rearward-facing position. • Make sure the Swivel ’n Go seat is in a locked position with the release handle fully engaged. Test the seat after it is locked to see that it doesn’t swivel.

Removing Swivel ’n Go Premium Seating — If Equipped 1. Remove any obstructions from the floor behind the seat, and stow the third row seat. 2. Pull up on the release bar located at the bottom front edge of the swivel seat.

Release Bar

3. From behind the seat, lift up on the rear of the seat cushion while pulling the seat in a rearward direction. 4. Remove the seat from vehicle through the liftgate. Rollers are part of the seat frame and will ease the removal process.

5. Lower the release handle located at the bottom front edge of the seat. Each seat weighs about 90 lbs (81 kg). NOTE: Electrical contacts for the available heated seats automatically disengage or engage as the seat is removed or installed. The contacts slide past each other as the seat is rolled to and from the strikers. When reinstalling the seat, make certain to lower the release handle to ensure the seat is latched securely.

WARNING!

In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157

Swivel ’n Go Premium Seating Table — If Equipped The Swivel ’n Go Seating Table consists of an easily assembled post and top.

Second Row Seating and Table

158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

The table and leg are stored beneath the floor when not in use. To install the table follow these steps: 1. Open the floor storage cover in front of the second row seats.

3. Swivel the second row seats so they are facing the rear. 4. Insert pole into base by aligning the lock button into notch of the base.

Table and Leg Storage

2. Remove the pole and table top by loosening the hook and loop straps.

Installing Table Leg Into Base

1 — Table Base

2 — Lock/Release Button

5. Twist the pole in a clockwise rotation until it stops.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159

WARNING! (Continued)

• DO NOT place liquid drinks on the table, use • Second row seats must be locked in the rearward

available cupholders.

facing position before installing the table.

To separate the table top from the pole, follow these steps: 1. Locate the release latch on the underside of the table top.

NOTE: You will hear an audible “click” when the lock button engages the base. 6. Place the table top over the installed pole aligning with the mating feature of the underside of the table top. Apply pressure on the table top and press downward. NOTE: You will hear an audible “click” when the table latch engages the pole.

WARNING!

Failure to comply with the following conditions could result in serious injury or even death. • DO NOT install the table while vehicle is in • NEVER drive the vehicle with only the pole in- • DO NOT place heavy or sharp objects on table.

motion.

stalled.

(Continued)

160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Table Top Release

2. Pull horizontally on the latch to activate the release from the pole. 3. While pulling on the latch, pull upward to remove the table top from the pole.

NOTE: The table top should be removed from the leg prior to removing the leg from its mounting base. 4. Locate the release button on the pole. Press the release button firmly to activate the release from the base. 5. While pressing the release button, twist the pole in a counterclockwise rotation until it stops. Pull upward to remove the pole from the base. 6. Place the pole on the underside of the table top and secure with the hook and loop straps. 7. Once the pole and table top are secured, you may place them in the floor storage bin in front of the second row seats. NOTE: Always store the table and pole in the floor storage bin when not in use.

Plastic Grocery Bag Retainer Hooks Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all rear seats and some front seats. The floor supports the partial weight of the bagged goods. Second Row Bench Seat — If Equipped While the bench seat does not stow in the floor, it is removable for added cargo space. Release levers are located on the rear leg assemblies, near the floor. To remove the seat, squeeze each release handle and rotate downwards to deploy the wheels. A lock indicator button pops up when the seat is unlocked. The seat assembly can now be removed from the vehicle and moved on its Easy Out威 Rollers.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161

Release Handles

To reinstall the seat, align the seat into the detent posi- tions on the floor. Squeeze the release handle and rotate upward until the lock indicator button returns into the handle.

162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

If not properly latched, the bench seats could become loose. Personal injuries could result. After reinstall- ing these seats, be sure the red indicator button on the release handles return into the handles.

Third Row Power Seat — If Equipped The third row power seat offers the following features: • The seatbacks can be folded forward for additional • Head restraints can be stowed with the seat. • Tailgate mode flips the seat rearward to face out the

cargo space if needed.

tailgate.

The power recline feature, located on the side of the seat cushion, adjusts the seatback angle forward/rearward for occupant comfort.

Third Row Power Seat Switch

Third Row Power Seat Switch — If Equipped A one-touch power folding seat switch is located in the left rear trim panel as part of a switch bank.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163

One Touch Folding Seat Third Row

The rear switch bank allows multiple power folding and unfolding positions for the third row seats. Left and right third row seats can be folded individually or together. The third row power folding seat adjusts to the following positions using the switch bank located on the left rear trim panel:

Rear Panel Power Switch Bank

1 — Open to Normal 2 — Stow 3 — Tailgate

4 — Fold Flat 5 — Right/Left Seats 5 — Both Seats

NOTE: The third row power seat system includes obstacle detection for safe operation. When the system detects an obstacle, the motors will stop and reverse the

164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

motion for a brief period. Should this occur, remove the obstacle and press the button again, for the desired position. To Fold Third Row Seats Manually — If Equipped 1. Lower the head restraint to its full down position. 2. Pull release strap marked “1” located on the rear of the seat to lower the seatback. 3. Pull release strap marked “2” to release the anchors.

Folding Third Row Seat Strap

4. Pull release strap marked “3” and tumble the seat rearward into the storage bin.

To Unfold Third Row Seats 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch. 2. Pull release strap marked “1” to unlock the recliner. 3. Pulling strap “3” releases the seatback to return to its full upright position. 4. Adjust the head restraint to the desired position.

WARNING!

In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165

Tailgate Mode 1. Pull release strap “2”, then pull release strap “3” to rotate the entire seat rearward.

Tailgate Positioning Release Straps 2 and 3

2. To restore the seat to its upright position, lift up on the seatback and push forward until the anchors latch.

166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

To avoid serious injury or death, NEVER operate the vehicle with occupants in the third row seat while in the tailgate mode.

DRIVER MEMORY SEAT SYSTEM — IF EQUIPPED Once programmed the Memory Buttons 1 and 2 on the driver’s door panel can be programmed to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings. Your Remote Keyless Entry (RKE) transmitters can also be programmed to recall the same positions when the UNLOCK button is pressed.

Driver Memory Seat Switch

Your vehicle may have been delivered with two RKE transmitters. Only one RKE transmitter can be linked to each of the memory positions.

Setting Memory Positions And Linking RKE Transmitter To Memory

NOTE: Each time the SET (S) button and a numbered button (1 or 2) is pressed, you erase the memory settings for that button and store a new one. 1. Insert the ignition key and turn the ignition switch to the ON position. 2. Press the driver door Memory button number 1 if you are setting the memory for driver 1, or button number 2
if you are setting the memory for driver 2. The system will recall any stored settings. Wait for the system to complete the memory recall before continuing to Step 3. 3. Adjust the driver’s seat, recliner, and driver’s side- view mirror to the desired positions. 4. Adjust the brake and accelerator pedals to the desired positions.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167

5. Turn on the radio and set the radio station presets (up to 10 AM and 10 FM stations can be set). 6. Turn the ignition switch to the OFF position and remove the key. 7. Press and release the SET (S) button located on the driver’s door. 8. Within five seconds, press and release Memory button 1 or 2 on the driver’s door. The next step must be performed within 10 seconds if you desire to also use a RKE transmitter to recall memory positions. 9. Press and release the LOCK button on one of the RKE transmitters. 10. Insert the ignition key and turn the ignition switch to the ON position.

168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

(EVIC). Refer

Information Center

11. Select ⬙Remote Linked to Memory⬙ in the Electronic Vehicle to the “Customer-Programmable Features” in the “Electronic Vehicle Information Center (EVIC)” section for more information. 12. Repeat the above steps to set the next Memory position using the other numbered Memory button or to link another RKE transmitter to memory. Memory Position Recall NOTE: The vehicle must be in PARK to recall memory positions. If a recall is attempted when the vehicle is not in PARK, a message will be displayed in the EVIC. To recall the memory settings for driver one, press Memory button 1 on the driver’s door or the UNLOCK button on the RKE transmitter linked to memory position 1.

To recall the memory setting for driver two, press Memory button 2 on the driver’s door or the UNLOCK button on the RKE transmitter linked to Memory Position 2. A recall can be cancelled by pressing any of the memory buttons on the driver’s door during a recall (S, 1, or 2). When a recall is cancelled, the driver’s seat, driver’s mirror, and the pedals stop moving. A delay of one second will occur before another recall can be selected. To Disable RKE Transmitter Linked to Memory 1. Turn the ignition switch to the OFF position and remove the key. 2. Press and release Memory button 1. The system will recall any memory settings stored in position 1. Wait for the system to complete the memory recall before continu- ing to Step 3.

3. Press and release the memory SET (S) button located on the driver’s door. A chime will sound signaling that you are in the memory set mode. 4. Within five seconds, press and release Memory button 1 on the driver’s door. A chime will sound signaling to you that the driver memory has been set. 5. Within five seconds, press and release the UNLOCK button on the RKE transmitter. A chime will sound signaling to you that the RKE transmitter link has been successfully disabled. To disable another RKE transmitter linked to either Memory Position, repeat Steps 1 to 5 for each RKE transmitter. NOTE: Once programmed, all RKE transmitters linked to memory can be easily enabled or disabled at one time.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169

Refer to the Remote Linked to Memory ⬙Customer- Programmable Features⬙ in the Electronic Vehicle Infor- mation Center (EVIC) for more information. Easy Entry/Exit Seat (Available with Memory Seat ONLY) This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. The distance the driver seat moves depends on where you have the driver seat positioned when you remove the key from the ignition switch. • When you remove the key from the ignition switch, the driver seat will move about 2.4 in (60 mm) rearward if the driver seat position is greater than or equal to 2.7 in (67.7 mm) forward of the rear stop. The seat will return to its previously set position when you insert the key into the ignition switch and turn it out of the LOCK position.

170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

• When you remove the key from the ignition switch the driver seat will move to a position 0.3 in (7.7 mm) forward of the rear stop if the driver seat position is between 0.9 – 2.7 in (22.7 – 67.7 mm) forward of the rear stop. The seat will return to its previously set position when you insert the key into the ignition switch and turn it out of the LOCK position. • The Easy Entry/Easy Exit feature is disabled when the driver seat position is less than 0.9 in (22.7 mm) forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for Easy Exit or Easy Entry.

Each stored memory setting will have an associated Easy Entry and Easy Exit Position.

NOTE: The Easy Entry/Easy Exit feature can be en- abled or disabled through the programmable features in the Electronic Vehicle Information Center (EVIC). If your vehicle is not equipped with an EVIC, your dealership can activate/deactivate this feature for you. For details, refer to “Automatically Move Seat Back on Exit,” section of this manual.

TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the hood release lever located on the instrument panel, below the steering column.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171

Hood Release Lever

Safety Lever Location

2. Move to the front of the vehicle and look inside the center of the hood opening. Locate, then push the safety catch lever to the right while raising the hood at the same time.

Use the hood prop rod to secure the hood in the open position. To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately

172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

12 in (30 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.

WARNING!

If the hood is not fully latched, it could open when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving.

LIGHTS All of the lights, except the Hazard warning lights, headlight high beams and flash-to-pass, are controlled by switches to the left of the steering column on the instru- ment panel.

Headlight Switch With Halo Control

Interior Lighting Interior lights are turned on when a door or liftgate is opened, the Remote Keyless Entry (RKE) transmitter is activated, or when the dimmer control is moved to the extreme top.

The interior lights will automatically turn off in approxi- mately 10 minutes for the first activation and 90 seconds every activation thereafter until the engine is started, if one of the following occur: • A door, sliding door or the liftgate is left open • Any overhead reading light is left on NOTE: The key must be out of the ignition switch or the ignition switch must be in the OFF position for this feature to operate. Dome Light Positions

Rotate the dimmer control completely upward to the second detent (extreme top position) to turn on the interior lights, reading/ courtesy lights. The interior lights will remain on when the dimmer control is in this position.

except

front

the

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173

Interior Lighting Defeat (Off)

Rotate the dimmer control to the off position (extreme bottom). The inte- rior lights will remain off when the doors or liftgate are open.

Parade Mode (Daytime Brightness Feature)

feature brightens

Rotate the dimmer control to the first detent. This the odometer, radio and overhead dis- plays when the parking lights or head- lights are on.

174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Dimmer Control

With the parking lights or headlights on, rotating the dimmer control for the interior lights on the instrument panel upward will increase the brightness of the instrument panel lights.

Halo Lights — If Equipped Halo lights are strategically placed soft lighting that help to illuminate specific areas to aid the occupants in locating specific features while driving at night.

To activate the Halo lights, push in the Halo switch control knob. Pressing the switch con- trol knob in a second time will turn the Halo lights off.

Parking Lights

Turn the headlight switch knob to the first detent to turn on the parking lights. This also turns on all

instrument panel lighting. Headlights

Turn the headlight switch knob to the second detent to turn the headlights and parking lights on. This also turns on all instrument panel lighting.

To change the brightness of the instrument panel lights, rotate the dimmer control up or down. Automatic Headlights — If Equipped This system automatically turns your headlights on or off based on ambient light levels. To turn the system on, turn the headlight switch to the extreme counterclockwise position aligning the indicator with the “A” on the headlight switch. When the system is on, the Headlight Time Delay feature is also on. This means your headlights

will stay on for up to 90 seconds after you turn the ignition switch OFF. To turn the Automatic System off, turn the headlight switch clockwise to the “O” off position.

Automatic Headlights

NOTE: The engine must be running before the head- lights will come on in the Automatic mode.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175

Headlights On With Wipers — If Equipped When your headlights are in the Automatic mode and the engine is running, the headlights will automatically turn on when the wiper system is also turned on. Headlights on when windshield wipers are on may be found on vehicles equipped with an automatic headlight system. Refer to the Electronic Vehicle Information Center (EVIC) in Section 4 under “Personal Settings (customer- programmable features)” for more information. Headlight Delay — If Equipped This feature provides the safety of headlight illumination for up to 90 seconds after exiting your vehicle. To activate the delay feature, turn OFF the ignition switch while the headlights are still on. Then turn off the headlights within 45 seconds. The 90 second delay inter- val begins when headlight switch is turned off. If the headlights or parking lights are turned back on or the ignition switch is turned ON, the delay will be cancelled.

176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

When exiting the vehicle the driver can choose to have the headlights remain on for 30, 60, or 90 seconds or not remain on. To change the timer setting, see your autho- rized dealer. The headlight delay time is programmable on vehicles equipped with an EVIC. Refer to “Delay Turning Head- lights Off,” under (Customer- Programmable Features)” under “Electronic Vehicle In- formation Center (EVIC)” in Section 4. If the headlights are turned off before the ignition, they will turn off in the normal manner. NOTE: The headlights must be turned off within 45 sec- onds of turning the ignition OFF to activate this feature.

“Personal Settings

Lights-On Reminder If the headlights or the parking lights are left on, or if the dimmer control is in the extreme top position after the ignition switch is turned OFF, a chime will sound when the driver’s door is opened. Daytime Running Lights (Canada/Fleet Vehicles Only) The headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except PARK. This provides a constant lights on condi- tion until the ignition is turned OFF. The lights illuminate at less than 50% of normal intensity. If the parking brake is applied, the Daytime Running Lights (DRL) will turn off. Also, if a turn signal is activated, the DRL lamp on the same side of the vehicle will turn off for the duration of the turn signal activation. Once the turn signal is no longer active, the DRL lamp will illuminate.

Front Fog Lights — If Equipped

To activate the front fog lights, turn on the parking lights or the low beam headlights and push in the headlight switch control knob. Pressing the head- light switch control knob in a second time will turn the front fog lights off. Battery Protection This feature provides battery protection to avoid wearing down the battery if the headlights, parking lights, or front fog lights are left on for extended periods of time when the ignition switch is in the LOCK position. After eight minutes of the ignition switch being in the LOCK position and the headlight switch in any position other than OFF or AUTO, the lights will turn off automatically until the next cycle of the ignition switch or headlight switch.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177

The battery protection feature will be disabled if the ignition switch is turned to any other position other than LOCK during the three minute delay. Multifunction Lever The multifunction lever is located on the left side of the steering column. The multifunction lever controls the: • Turn Signals • Headlight Beams Low/High • Flash-To-Pass (Optical Horn) • Front and Rear Wipers — Washer Functions

178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Turn Signals Move the multifunction lever up or down to signal either a right or left turn.

Turn Signals

The arrow on either side of the instrument cluster flashes to indicate the direction of the turn and proper operation of the front and rear turn signal lights.

If either indicator flashes at a rapid rate, check for a defective outside turn signal light bulb. If one of the indicators fails to light when the lever is moved, it would suggest that the indicator light is defective. You may manually signal a lane change by moving the lever partially up or down. Turn Signal Auto-Mode Tap the multifunction lever once and the turn signal (left or right) will flash three times and automatically turn off. Turn Signal Warning If the vehicle electronics sense that the vehicle has traveled at over 18 mph (29 km/h) for about 1 mile (1.6 km) with the turn signals on, a chime will sound to alert the driver.

High Beam/Low Beam Select Switch When the headlights are turned on, pushing the multi- function lever toward the instrument panel will switch from Low beams to High beams. Pulling back to the neutral position returns the headlights to the Low beam operation. Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will cause the headlights to turn on at High beam and remain on until the multifunction lever is released.

WINDSHIELD WIPER AND WASHERS The wipers and washers are operated by a switch within the multifunction lever. Rotate the end of the multifunc- tion lever to select the desired wiper speed. NOTE: Always remove any buildup of snow that pre- vents the windshield wiper blades from returning to the

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179

off position. If the windshield wiper switch is turned off and the blades cannot return to the off position, damage to the wiper motor may occur.

Washer And Wiper Controls

1 — Front Mist/Washer 2 — Wiper Speeds

3 — Rear Wiper/Washer

180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

1. Mist, Front Wiper and Washer Press the end of the multifunction lever inward to the first detent and release to clear the windshield. Pressing the multifunction lever inward to the second detent will cause the washers to spray for a maximum of 10 seconds, or until the multifunction lever is released, and the wipers will cycle three times. NOTE: • If the multifunction lever is depressed while in the delay range, the wipers will operate for several sec- onds after the multifunction lever is released, and then resume the intermittent interval previously selected. • If the multifunction lever is depressed while in the off position, the wipers will operate for approximately two wipe cycles and automatically turn off.

2. Intermittent, Low and High Speed Wipers Use the intermittent wipers when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Rotate the end of the multifunc- tion lever to the first detent position, then turn the end of the multifunction lever to select the desired delay inter- val. The delay can be regulated from approximately 2 seconds, to a maximum of 20 seconds between cycles. The time delay will be doubled if the vehicle speed is less than 10 mph (16 km/h). Low Speed is achieved by rotating the multifunction lever past the intermittent settings, to the first detent. High Speed is achieved by rotating the multifunction lever past the intermittent settings, to the second detent.

3. Rear Wiper and Washer Rotating the rotary ring to the first detent activates the rear intermittent wipers. To activate the washers, rotate the rotary ring fully forward and the washers will spray until the ring is released, and then resume the intermit- tent interval. NOTE: Rear window wipers function in the intermittent wiper speed only.

WARNING!

Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181

TILT STEERING COLUMN — IF EQUIPPED To tilt the column, pull the lever downward (located on the steering column and below the steering wheel) to the open position. You may then position the steering wheel up or down, as desired. Pull the small lever upward to the closed position to lock the steering wheel firmly in place.

WARNING!

Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.

182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat positions. The switch is located on the left side of the steering column.

Tilt Steering Column Lever

1 — Closed 2 — Opened

ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward, or away, from the driver to provide

Adjustable Pedal Switch

Press the button forward to move the pedals forward (toward the front of the vehicle). Press the button rearward to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF. • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control Sys- tem is on. The following messages will be displayed on vehicles equipped with the Electronic Vehicle In- formation System (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjust- able Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183

CAUTION!

Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path.

ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h).

184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Electronic Speed Control Switches

To Activate Push the ON/OFF button (located in the end of the lever) once, and the cruise indicator light (located in the mes- sage window of the odometer) will illuminate showing that the Electronic Speed Control system is on. To turn the Electronic Speed Control system off, push the ON/

OFF button a second time, and both the Electronic Speed Control system and indicator will turn off.

WARNING!

Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the Electronic Speed Control system off when you are not using it.

To Set At A Desired Speed When the vehicle has reached the desired speed, press the SET lever downward and then release. Lift your foot off the accelerator and the vehicle will operate at the selected speed.

Deactivating Electronic Speed Control A soft tap on the brake pedal or pulling the Electronic Speed Control lever (CANCEL) toward you will deacti- vate the Electronic Speed Control without erasing the set speed memory. Pushing the ON/OFF button to the OFF position or turning OFF the ignition erases the set speed memory. Resuming Speed To resume a previously set speed, raise the Electronic Speed Control lever (RESUME/ACCEL) upward, and release. Resume can be used at any speed above 25 mph (40 km/h). Varying The Speed Setting When the Electronic Speed Control is SET, speed can be increased by raising and holding the RESUME/ACCEL lever upwards. When released, a new set speed will be established.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185

Raising the RESUME/ACCEL lever upward, once, will result in a 1 mph (1 km/h) speed increase. Each time the lever is tapped upward speed increases, so tapping the Electronic Speed Control lever three times will increase speed by 3 mph (5 km/h), etc. To decrease speed while speed control is set, press the SET/DECEL lever downward, and hold. Release the Electronic Speed Control lever when the desired speed is reached, and the new speed will be set. Tapping the SET/DECEL lever downward, once, will result in a 1 mph (1 km/h) speed decrease. Each time the Electronic Speed Control lever is tapped downward, speed decreases. In order to ensure proper operation the Elec- NOTE: tronic Speed Control system has been designed to shut down if multiple speed control switch functions are operated simultaneously. If this occurs, the Electronic

186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Speed Control system can be reactivated by pushing the Electronic Speed Control switch ON/OFF button and resetting the desired vehicle set speed. Accelerating To Pass Depress the accelerator as you normally would. When the pedal is released, the vehicle will return to the set speed. NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal. Your vehicle may experience a downshift (automatic transmissions only) while climbing uphill or descending downhill. This downshift is necessary to maintain vehicle set speed. On steep hills, a greater speed loss or gain may occur, so it may be preferable to drive without Electronic Speed Control.

WARNING!

Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.

REAR PARK ASSIST SYSTEM — IF EQUIPPED The Rear Park Assist system provides visible and audible indications of the distance between the rear fascia and the detected obstacle, when backing up. When backing up, you should also use the inside rearview and outside mirrors.

The Rear Park Assist system will remember the last system state (enabled or disabled) from the last ignition cycle, when the ignition is changed to the RUN/ON position. The Rear Park Assist system can be active only when the shift lever is in REVERSE. When in REVERSE, the system scans for objects behind the vehicle, using four sensors located in the rear bumper. NOTE: The system will be active until the vehicle speed is increased to approximately 11 mph (18 km/h) or above. The system will be active again if the vehicle speed is decreased to speeds less than approximately 10 mph (16 km/h).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187

Rear Park Assist Sensors The four rear park assist sensors, located in the rear fascia, monitor the area behind the vehicle that is within the sensors’ field of view. The monitored area seems oval in shape. The sensors can detect obstacles from approxi- mately 11.8 in (30 cm) up to 78.7 in (200 cm) from the rear fascia in the horizontal direction, depending on the location and orientation of the obstacle and the type of obstacle. Rear Park Assist Warning Display The Rear Park Assist Warning Display, located in the headliner near the liftgate glass, provides both visible and audible warnings to indicate the distance between the rear fascia and the detected obstacle.

188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Rear Park Assist LED Lights

When the ignition switch is turned to the RUN/ON position, the warning display will turn on all of its LEDs

for about one second. Each side of the warning display has six yellow and two red LED lights, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle. The vehicle is close to the obstacle when the red LED is illuminated. The driver can view the LEDs either through the rear- view mirror or by looking directly at the display above the rear window. The system dimly illuminates the two innermost yellow LEDs when it is on and detects no obstacles. The follow- ing chart shows the warning display operation when the system is detecting an obstacle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189

WARNING DISPLAY DISTANCES

DISPLAY

INDICATOR

Inner LED 1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED

OBSTACLE DISTANCE FROM:

REAR CORNERS

31.5 in (80 cm) 25.5 in (65 cm) 20 in (50 cm) 16 in (40 cm) 6 in (15 cm)

REAR CENTER 59 in (150 cm) 51.2 in (130 cm) 45.3 in (115 cm) 39.3 in (100 cm) 33.5 in (85 cm) 27.6 in (70 cm) 19.7 in (50 cm) 11.8 in (30 cm)

INDICATOR

COLOR Yellow Yellow Yellow Yellow Yellow Yellow Red Red

AUDIBLE SIGNAL

Yes, Half Second

No No No No No

Yes, Intermittent Yes, Continuous

NOTE: The Rear Park Assist system will MUTE the radio, if on, when the audible warning is activated.

190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

• Drivers must be careful when backing up, even when using the Rear Park Assist System. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.

(Continued)

WARNING! (Continued)

• Before using the Rear Park Assist system, it is strongly recommended that the ball mount and hitch ball assembly be disconnected from the vehicle, when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles, because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns the red LEDs on. Also, the sensors could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle.

CAUTION!

• To avoid vehicle damage, the Rear Park Assist system should only be used as a parking aid and is unable to recognize every obstacle, including small objects. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity to the rear of the vehicle. • To avoid vehicle damage, the vehicle must be driven slowly when using the Rear Park Assist system, to be able to stop in time when an obstacle is detected. It is recommended that you look over your shoulder when using the Rear Park Assist system.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191

NOTE: • Ensure that the rear bumper is free of dirt and debris • Jackhammers, large trucks, and other vibrations could

to keep the system operating properly.

affect the performance of the system.

Enabling and Disabling The Rear Park Assist System There are times when you may want to disable the Rear Park Assist System, such as when towing a trailer. Vehicles Equipped With the Electronic Vehicle Information Center (EVIC) You can turn the Rear Park Assist System ON or OFF through the EVIC. For details, refer to “Personal Settings (Customer Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4.

192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Vehicles Equipped With the Compass Mini-Trip Computer (CMTC) You can turn the Rear Park Assist system ON or OFF through the CMTC by pressing the left reset button in the instrument cluster. Turn the ignition switch to the ON position, then press and hold the RESET button for approximately two seconds. Service The Rear Park Assist System If the Rear Park Assist system malfunctions, the instru- ment cluster will actuate a single chime, once per ignition cycle, and it will display the ⴖSERVICE PARK ASSIST SYSTEMⴖ message. Refer to “Compass Mini Trip Com- puter (CMTC) or “Electronic Vehicle Information Center (EVIC) — If Equipped”, in Section 4. If ⴖSERVICE PARK ASSIST SYSTEMⴖ appears in the Electronic Vehicle Information Center (EVIC), after mak- ing sure the rear bumper is clean, please see your authorized dealer.

Should this wrench symbol display with the letter P next to it, your Park Sense system needs servicing. Contact your authorized dealer.

Cleaning The Rear Park Assist System Clean the Rear Park Assist sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors, otherwise, you could damage them.

REAR BACKUP CAMERA SYSTEM — IF EQUIPPED Your vehicle may be equipped with a Rear Camera System that allows you to see an on-screen image of the rear of your vehicle whenever the shift lever is put into REVERSE. The Rear camera image will be displayed on the radio display screen, located on the center stack of the instrument panel. The camera is located in the light bar over the rear license plate.

NOTE: The Rear Camera system can be enabled and disabled, refer to your Radio/Navigation/Multimedia manual. Use the following steps to access the Rear Backup Cam- era feature: 1. Start the engine. 2. Place the shift lever into REVERSE. 3. Wait one to two seconds, and the camera view will display on the radio display screen. NOTE: The camera view will display only while the vehicle is in REVERSE. 4. Perform a thorough visual check of the rear area.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193

5. Backup as necessary. 6. Place the shift lever in PARK or DRIVE to exit the Rear Backup Camera system.

WARNING!

Drivers must be careful when backing up even when using the Rear Backup Camera System. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.

194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!

• To avoid vehicle damage the Rear Backup Camera System should only be used as a parking aid and is unable to view every obstacle, or object in your drive path. • To avoid vehicle damage the vehicle must be driven slowly when using the Rear Backup Cam- era System to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/her shoulder.

If snow, ice, mud, or anything else builds up on NOTE: the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens.

OVERHEAD CONSOLES

Front Overhead Console Two versions of the overhead console are available. The base front overhead console model featured fixed incan- descent courtesy/reading lights, flip-down sunglass stor- age and conversation mirror. The premium front over- head console model features a LED focused light that illuminates the instrument panel cupholders, Infrared Automatic Temperature Control Sensor (ATC equipped only), two swiveling LED lights, flip-down sunglass storage, conversation mirror, optional power sliding door switches and an optional power liftgate switch. NOTE: Premium sunroof console models include all of above except sunglass storage.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195

when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE), the lights will also turn on when the UNLOCK button on the transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle. Press a second time to turn each light off. You may adjust the direction of these lights by pressing the outside ring, which is identified with four directional arrows. (LED lamps only). The area around the instrument panel cupholders is also illuminated from a light in the overhead console (Pre- mium console only). This light is turned on when the headlight switch is on, and will adjust in brightness when the dimmer control is rotated up or down. Sunglass Storage (non-sunroof only) At the rear of the front overhead console, a compartment is provided for the storage of two pairs of sunglasses.

Front Premium Overhead Console Features

1 — Cupholder LED 2 — ATC Sensor 3 — Interior Lights

4 — Storage/Mirror 5 — Switch Bank

Courtesy/Interior Lighting At the forward end of the console are two courtesy lights (standard dome light has two buttons). The lights turn on

196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Press the door latch to open the compartment. The door will slowly rotate to an open position. Rotating bin upward to partial open, positions lid for conversation mirror use. NOTE: The front overhead console supplied with fac- tory sunroof, incorporates a sunroof switch. Rear Overhead Consoles — If Equipped The rear overhead storage system is available in two versions: with or without sunroof. An additional LED at the front of the rear console shines down on the front foot-well area while in courtesy mode, for added convenience.

Overhead Compartment Features

1 — DVD 1
2 — Rear HVAC 3 — Interior Lights 4 — Storage 1 If equipped, otherwise storage.

5 — Storage 6 — DVD 1
7 — Interior Lights 8 — Halo Lighting

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197

Lights — If Equipped” under “Lighting” in the “Under- standing The Features Of Your Vehicle” in Section 2.

GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLink威 unit operates off your vehicle’s battery. The HomeLink威 buttons that are located in the headliner or sun visor designate the three different HomeLink威 channels.

Rear Courtesy/Reading Lights — If Equipped The overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with RKE, the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle. Press the lens a second time to turn each light off. You may adjust the direction of these lights by pressing the outside ring, which is identified with four directional arrows. Rear Console Halo Lighting The rear overhead console has recessed halo lighting around the perimeter of the console base. This feature provides additional lighting options while traveling and is controlled by the headlight switch. Refer to ”Halo

198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

HomeLink威 Buttons

NOTE: HomeLink威 is disabled when the Vehicle Secu- rity Alarm is active.

WARNING!

• Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this trans- ceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety information or as- sistance. • Vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death.

Programming Homelink姞

Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for up to 20 seconds until the red indicator flashes. It is recommended that a new battery be placed in the handheld transmitter of the device being programmed to HomeLink威 for more efficient training and accurate transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage when programming. Begin Programming 1. Turn the ignition switch to the ON/RUN position. 2. Hold the battery side of the handheld transmitter away from the HomeLink威 button you wish to program.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199

Place the handheld transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink威 button you wish to program while keeping the indicator light in view. 3. Simultaneously press and hold both the chosen HomeLink威 button and the handheld transmitter button until the HomeLink威 indicator changes from a slow to a rapidly blinking light, then release both the HomeLink威 and handheld transmitter buttons. Watch for the HomeLink威 indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds, or longer in rare cases. The garage door may open and close while you train. NOTE: • Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section.

200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

• After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the ga- rage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, proceed to Step 5 “Programming A Rolling Code System.”

4. Press and hold the just-trained HomeLink威 button and observe the indicator light. If the indicator light stays on constantly, programming is complete and the garage door (or device) should activate when the HomeLink威 button is pressed. If the indicator light blinks rapidly for two seconds and then turns to a constant light, proceed to Step 5 “Pro- gramming A Rolling Code System.” 5. Programming A Rolling Code System At the garage door opener motor (in the garage), locate the “Learn” or “Training” button.

This can usually be found where the hanging antenna wire is attached to the garage door opener motor. It is NOT the button normally used to open and close the door.

Training The Garage Door Opener

1 — Door Opener 2 — Training Button

6. Firmly press and release the “Learn” or “Training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. To program the remaining two HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201

Using HomeLink威 To operate, simply press and release the programmed HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc. The handheld transmitter of the device may also be used at any time. Reprogramming a Single Homelink威 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button, proceed with Program- ming Homelink威 Step 2 and follow all remaining steps.

202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Gate Operator/Canadian Programming Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace “Programming HomeLink威” Step 3, with the following: 3. Continue to press and hold the HomeLink威 button while you press and release - every two seconds (“cycle”) your handheld transmitter until HomeLink威

has successfully accepted the frequency signal. The indicator light will flash slowly and then rapidly when fully trained. If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Programming HomeLink威,” earlier in this section. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The HomeLink威 Universal Transceiver is disabled when the Vehicle Security Alarm is active.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203

2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for com- pliance could void the user’s authority to operate the device. • The term IC before the certification/registration num- Industry Canada technical

ber only signifies that specifications were met.

Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the “Learn” button on the Garage Door Opener • Did you unplug the device for training, and remember

to complete the training for a Rolling Code.

to plug it back in?

If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference.

204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

POWER SUNROOF — IF EQUIPPED The power sunroof control switch is located in the front overhead console.The sunroof panel tilts upward at the rear for ventilation or slides rearward under the roof. Power Sunroof Operation

Opening the Sunroof Manually Press the switch rearward and hold, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. During this opera- tion, any release of the sunroof switch will stop the sunroof.

WARNING!

In an accident, there is greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured.

Closing the Sunroof Manually To close the sunroof from an open or vent position, press and hold the switch forward. The sunroof will close fully and stop automatically. Release the switch to stop sun- roof travel at any point. Sunroof Sunshade Operation The sunroof sunshade can be opened manually. How- ever, the sunshade will open automatically as the sunroof opens.

NOTE: The sunshade cannot be closed if the sunroof is open.

WARNING!

Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sun- roof while operating the power sunroof switch. Such entrapment may result in serious injury or death.

Express-Open Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called Express-Open. During Express-Open operation, any movement of the sunroof switch will stop the sunroof.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205

Express-Vent Press and release the ⬙V⬙ button, and the sunroof will automatically open to the vent position. This is called Express-Vent. Express-Close Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully, then stop automatically. This is called Express-Close. During Express-Close operation, any movement of the sunroof switch will stop the sunroof.

WARNING!

Do not allow small children to operate the sunroof. Never allow fingers or other body parts, or any object to project through the sunroof opening. Injury may result.

206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Ignition OFF Operation The power sunroof switch will remain active for 10 min- utes after the ignition switch is turned OFF. Opening either front door will cancel this feature. Auto-Express with Anti–Pinch Protection During express closing, anytime an obstacle that restricts glass movement is detected, the motor will stop and reverse travel to avoid pinching the object. Auto Express will stop and reverse travel up to three times in succession. After the third time, Auto Express will enter a manual operation mode. This allows the operator to manually control the power switch, in order to close or open the sunroof in case of a malfunction. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain

open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel.

ELECTRICAL POWER OUTLETS — IF EQUIPPED Two 12-Volt power outlets are located on the lower instrument panel next to the open storage bin. The upper outlet is controlled by the ignition switch and the lower outlet is connected directly to the battery. The upper outlet will also operate a conventional cigar lighter unit (if equipped with an optional Smoker’s Package).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207

The lower outlet is protected by an automatic reset circuit breaker. The automatic circuit breaker restores power when the overload is removed. The circuit breaker also supplies power to the outlet in the removable floor console, when in the front position. Refer to Section 3, “Removable Floor Console” in this manual. If desired, all of the power outlets can be NOTE: converted by your authorized dealer to provide power with the ignition switch in the OFF position.

CAUTION!

• Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.

(Continued)

12-Volt Power Outlets

The outlets include tethered caps labeled with a key or battery symbol indicating the power source. The lower instrument panel outlet is powered directly from the battery. Items plugged into this outlet may discharge the battery and/or prevent engine starting.

POWER INVERTER — IF EQUIPPED A 110-Volt, 150-Watt inverter outlet (if equipped) con- verts DC current to AC current, and is located on the left rear trim panel immediately behind the second row left passenger seat. This outlet can be used to power small appliances and electronics.

208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION! (Continued)

• Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery. • Power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug. Improper use of the power outlet can cause damage.

Power Inverter Outlet

The Power Inverter switch is located near the center of the instrument panel below the two 12-Volt power out- lets. Press the switch to turn the power on for the outlet, press the switch a second time to turn the power off.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209

CUPHOLDERS There are nine cupholders in the interior. Two cupholders in the center front instrument panel, four in the floor consoles and three more are located in the third row quarter trim panel. All liners are removable for cleaning. Pull the flexible liner from the cupholder drawer or tray starting at one edge for easy removal. Refer to “Cleaning The Instru- ment Panel Cupholders” in Section 7. Instrument Panel Cupholders The instrument panel cupholders are located in a pull-out drawer just above the lower storage bin.

Power Inverter Switch

210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Front Cupholders

Pull the drawer out firmly until it stops, and place the container to be held in either one of the cupholder wells. The cupholders are designed to accommodate a wide variety of container types and sizes. Press down on the container to engage the cupholder retention features.

Interior Bottle Holders There are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel. Each holder accommo- dates up to a 20 oz (1 L) plastic bottle. Two outboard mesh pockets are on intermediate seating. The mesh pockets are flexible enough to hold juice boxes, toys, games or MP3 players, etc. Smoker’s Package Kit — If Equipped With the optional authorized dealer-installed Smoker’s Package Kit, a removable ash receiver is inserted into one of the two cupholders in the center front instrument panel. To install the ash receiver, align the receiver so the thumb grip on the lid is facing rearward. Press the ash receiver into either of the cup wells to secure. Pull upward on the ash receiver to remove for cleaning and/or storage.

The left rear trim panel cupholder is designed to accom- modate a second ash receiver, if desired.

STORAGE

Glove Compartments There are both upper and lower glove compartments. Upper Glove Compartment To open the upper compartment, press in on the upper latch. The door will spring open about 1 in (2.54 cm). Manually lift the front edge of the door upward until fully opened and the detent is engaged. To close the compartment door, firmly push downward on the door’s surface to release the detent and latch the door closed.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211

1 — Lower Compartment 2 — Lower Latch/Lock

Glove Compartment Features 3 — Upper Latch 4 — Upper Compartment

212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Lower Glove Compartment To open the lower compartment pull out on the release handle. NOTE: The lower compartment is equipped with a lock that is part of the compartment handle (2). Door Trim Panel Storage

Front Door Storage Both interior front door panels have multiple pockets for storage.

Front Door Storage

1 — Rear Map Pocket 2 — Storage Pocket

3 — Bottle Holder 4 — Front Map Pocket

Sliding Side Door Bottle Holder Both sliding doors have a bottle holder molded right into the trim.

Driver Seatback Storage — If Equipped The driver’s seatback has a primary storage pocket on all models and an optional secondary mesh pocket.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213

Sliding Door Bottle Holder

Driver’s Seatback Storage

1 — Standard Pocket 2 — Mesh Pocket 3 — Bag Holder

4 — Bottle Holder 5 — Side Mesh Pocket

214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Second Row Seat Storage Bins — If Equipped The seat storage bins are located on the floor in front of the second row seats. The area below the covers can be used for storage when the second row seat is in the upright position. Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the ⬙Lock⬙ position to allow greater access to the storage bin.

Storage Bin

CAUTION!

NOTE: The storage bin cover must be locked and flat to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.

WARNING!

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215

In an accident, serious injury could result if the seat storage bin covers are not properly latched. • DO NOT drive the vehicle with the storage bin • Keep the storage bin covers closed and latched • DO NOT use a storage bin latch as a tie down.

while the vehicle is in motion.

covers open.

Rear Compartment Storage Bins Your vehicle is equipped with open storage areas located in each rear trim panel.

Rear Compartment Details

1 — Tie Down 2 — Switch Bank 3 — Tire Jack/Handle 4 — Cubby/Speaker

5 — Liftgate Close Switch 6 — Bag Holders 7 — Child Seat LATCH Anchor 8 — Rechargeable Flash Light

216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle. Cargo Area Storage The liftgate sill plate has a raised line with the statement “Load To This Line”. This line indicates how far rearward cargo can be placed without interfering with liftgate closing.

Rear Cargo Area Loading Limit

NOTE: With all rear seats stowed or removed, 4 x 8 foot sheets of building material will fit on the vehicle floor with the liftgate closed. The front seats must be moved slightly forward of the rearmost position.

easily pass through the first row to the second.

CONSOLE FEATURES There are two consoles available: Basic and Premium. Basic Console Basic Console features consist of the following: • The basic console profile allows vehicle occupants to • Four cupholders accept up to extra large size beverage cups or 20 oz (.6 L) plastic bottles. Cupholders are dishwasher safe for cleaning. • The cupholders are removable to access a large storage • The basic console is removable from the vehicle for additional floor space by removing the cap and clip at the console base.

bin.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217

Basic Console Features

1 — Console Anchor 2 — Top Tray

3 — Front Cupholders 4 — Rear Cupholders

To Remove The Basic Floor Console 1. Remove the front anchor cup plug and clip.

218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

2. Slide the console base forward while lifting slightly to clear the rear load floor hook. 3. Remove the console. To Reinstall The Basic Floor Console 1. Position the console at a slight angle (front slightly higher than the rear). 2. Slide the console rearward into the floor bracket/ hook. 3. Align the console until the front anchor cup plug hole is centered on the winch hole. 4. Reinstall the clip first and then while pushing down- ward on the console with slight pressure, reinstall the cover plug. 5. Pull up on the console to be sure it is firmly latched.

WARNING!

In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.

Premium Console — If Equipped The three-compartment console with sliding storage bin, sliding upper tray with storage and large console storage bin offers multiple configurations. • Four cupholders with dishwasher safe liners for clean- ing. The cupholders can accept plastic bottles, large cups or mugs with handles.

• Top tray storage • Upper storage bin can hold nine regular or 18 thin CDs

or other items

• Large console center storage will store headphones for the available rear DVD entertainment system or other items • 12-Volt DC power outlet provides continuous power inside the console for cell phones or other electronics. • Rear occupant accessible • Multiple adjustments • Removable from vehicle for additional floor space.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219

Premium Console Features

1 — Top Release 2 — Center Release

3 — Console Release

220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

The top and center console sections slide forward and rearward to provide added user comfort. A one-piece cup holder insert for both cavities can easily be removed for cleaning. The cupholders will also accommodate large size cups and 20 oz (.6 L) bottles. Position 1 shows the console closed with four cupholders and a convenient storage tray.

Console Position 1

Position 2 shows the raised storage tray revealing a large storage area below.

easy access to the storage area below and provides two of the four cupholders for the second row passengers.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221

Console Position 2

Console Position 3

Dual Storage Bins Position 3 shows the top portion of the console in a rearward position. This is accomplished by lifting the upper most latch at the front of the console. This provides

Position 4 shows the complete console in its rearmost position. Again, lifting second latch handle at the front of the console, allows complete access to a lower storage bin and provides additional cupholders for rear passengers.

222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Console Position 4

To Remove The Premium Floor Console 1. Pull up on the bottom release handle in the front of the console 2. Lift centimeters

the console up several

the rear of

inches/

3. Pull rearward to disengage from floor and remove console To reinstall the console: 1. Position the console at a slight angle (rear slightly higher than the front) 2. Slide the console forward into the floor bracket 3. Rotate the rear of the console down until it is resting on the floor bracket 4. Push down on the rear of the console until it is seated in the rear floor bracket 5. Pull up on the console to be sure it is firmly latched

WARNING!

In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.

ELECTRIC REAR WINDOW DEFROSTER — IF EQUIPPED

Press the rear window defroster button (located on your front climate control) to turn on the rear window defroster and the optional heated mirrors. A light will illuminate to show that the defroster is on. The defroster automatically turns off after approximately ten minutes of operation, as long as the ignition switch is in the ON position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223

After the initial time interval has expired, if the rear window defogger switch is pressed to the on position again (during the same ignition cycle), the system will automatically turn off after approximately five minutes. NOTE: You may turn off the heated mirror feature at anytime by pressing the rear window defogger switch a second time.

CAUTION!

To avoid damaging the electrical conductors of the rear window defroster, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. Labels can be peeled off after soaking with warm water.

224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

UMBRELLA HOLDER An umbrella holder has been conveniently molded into the left front door entry scuff molding.

LOAD-LEVELING SYSTEM The automatic load-leveling system will provide a level riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6 km) of driving for the leveling to complete depending on road surface conditions. If the leveled vehicle is not moved for approximately 15 hours, the leveling system will bleed itself down. The vehicle must be driven to reset the system.

Umbrella Holder

WARNING!

Do not install the load-leveling system on vehicles that are not equipped with Anti-Lock Brakes. Ve- hicles without Anti-Lock Brakes (ABS) have a height- sensing proportioning valve. Installing a leveling system will render this system ineffective, inappro- priately reducing rear brake pressure, resulting in increased stopping distances. You could have a seri- ous accident.

ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and side rails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225

inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity. To move the crossbars, loosen the thumb screws located at the upper edge of each crossbar approximately six turns, then move the crossbar to the desired position, keeping the crossbars parallel to the rack frame. Once the crossbar is in place, retighten the thumb screws to lock the crossbar into position. Attempt to move the crossbar again to ensure that it has properly locked into position. NOTE: To help control wind noise when installing the crossbars make sure the arrows marked on the underside of the crossbars are facing the front of the vehicle. When the crossbars are not in use, the front crossbar should be fastened just forward of the middle support and the rear crossbar should be fastened at the rearmost position of the side rails. This will help reduce the amount of wind noise when the crossbars are not in use.

226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

The tie down holes on the crossbar ends should always be used to tie down the load. Check the straps frequently to be sure that the load remains securely attached.

CAUTION!

• Crossbars should remain equally spaced or paral- lel at any luggage rack position for proper func- tion. Noncompliance could result in damage to the luggage rack, cargo and/or vehicle. • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropri- ately.

(Continued)

CAUTION! (Continued)

• Long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. • Travel at reduced speeds and turn corners care- fully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift to a load. This is especially true on large flat loads and may result in damage to the cargo or your vehicle.

WARNING!

Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.

SUN SCREENS — IF EQUIPPED Sun screens are available for second and third row seating windows. The screens store in the sill trim panels, and the tops of the windows are equipped with hooks that the sun screens attach to when pulled out.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227

Sun Screen Retracted

Gently pull up on the tab to raise the sun screen. Continue pulling the sun screen until the tab is near the top of the window.

228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Sun Screen Attaching To Retainer Clips

Sun Screen Extended

Once the screen is completely to the top of the window, extend the top bar of the sun screen over the two hooks attached to the top of the window.

To lower the sun screen, gently lift the tab upward to disengage the hooks, and feed the screen back into the base sill.

UNDERSTANDING YOUR INSTRUMENT PANEL

CONTENTS

䡵 Instrument Panel Features . . . . . . . . . . . . . . . . 233
䡵 Instrument Cluster – Base . . . . . . . . . . . . . . . . 234
䡵 Instrument Cluster – Premium . . . . . . . . . . . . 235
䡵 Instrument Cluster Descriptions . . . . . . . . . . . . 236
䡵 Compass Mini-Trip Computer (CMTC) — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
▫ CMTC Odometer Display . . . . . . . . . . . . . . . 249
▫ CMTC Reset Buttons . . . . . . . . . . . . . . . . . . 249

▫ Compass/Temperature Display . . . . . . . . . . . 250

䡵 Electronic Vehicle Information Center (EVIC) —

If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . . . 252
▫ EVIC Displays . . . . . . . . . . . . . . . . . . . . . . . 254
▫ Trip Functions . . . . . . . . . . . . . . . . . . . . . . . 255
▫ Compass Display . . . . . . . . . . . . . . . . . . . . . 257
▫ Personal Settings (Customer-Programmable

Features) . . . . . . . . . . . . . . . . . . . . . . . . . . . 259

230 UNDERSTANDING YOUR INSTRUMENT PANEL

䡵 AM/FM/CD/DVD Multimedia System Radio

(RER/REN) – If Equipped . . . . . . . . . . . . . . . . 263
▫ Operating Instructions — Voice Recognition

System (VR) — If Equipped . . . . . . . . . . . . . 263

▫ Operating Instructions — Hands-Free

Communication (UConnect威) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 263
▫ Clock Setting Procedure . . . . . . . . . . . . . . . . 263

䡵 Sales Code RES — AM/FM Stereo Radio With

CD Player (MP3 AUX Jack). . . . . . . . . . . . . . . . 266
▫ Operating Instructions — Radio Mode . . . . . . 266
▫ Operation Instructions — CD Mode For CD

And MP3 Audio Play . . . . . . . . . . . . . . . . . . 269
▫ Notes On Playing MP3 Files . . . . . . . . . . . . . 271
▫ Operation Instructions - Auxiliary Mode . . . . 274

䡵 Sales Code RES/RSC — AM/FM Stereo Radio

With CD Player (MP3 AUX Jack) And Sirius Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
▫ Operating Instructions — Radio Mode . . . . . . 275
▫ Operation Instructions — CD Mode For CD

And MP3 Audio Play . . . . . . . . . . . . . . . . . . 280
▫ Notes On Playing MP3 Files . . . . . . . . . . . . . 282
▫ List Button (CD Mode For MP3 Play) . . . . . . 285
▫ Info Button (CD Mode For MP3 Play) . . . . . . 285

䡵 Universal Consumer Interface (UCI) — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
▫ Connecting The iPod威 . . . . . . . . . . . . . . . . . 287
▫ Using This Feature . . . . . . . . . . . . . . . . . . . 287
▫ Controlling The iPod威 Using Radio

Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288

▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 288
▫ List Or Browse Mode . . . . . . . . . . . . . . . . . . 289

䡵 Satellite Radio — If Equipped

(REN/REQ/RER/RES/REU Radios Only). . . . . 291
▫ System Activation . . . . . . . . . . . . . . . . . . . . 292
▫ Electronic Serial Number/Sirius

Identification Number (ESN/SID) . . . . . . . . . 292
▫ Selecting Satellite Mode . . . . . . . . . . . . . . . . 293
▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . 293
▫ Reception Quality . . . . . . . . . . . . . . . . . . . . 293
▫ Operating Instructions — Satellite Mode . . . . 293
▫ Operating Instructions — Hands-Free Phone

(If Equipped). . . . . . . . . . . . . . . . . . . . . . . . 296

UNDERSTANDING YOUR INSTRUMENT PANEL 231

▫ Operating Instructions — Video Entertainment System (VES)™ (If Equipped). . . . . . . . . . . . . . . . . . . . . . . . 296
䡵 Sirius Backseat TV™ — If Equipped . . . . . . . . 297
䡵 Video Entertainment System (VES)™ — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297

䡵 Remote Sound System Controls —

If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . . . 299
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . 299
▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . 300
䡵 CD/DVD Maintenance . . . . . . . . . . . . . . . . . . 300
䡵 Radio Operation And Cellular Phones . . . . . . . 301

232 UNDERSTANDING YOUR INSTRUMENT PANEL

䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 301

▫ Manual Heating, Ventilation And Air

Conditioning (HVAC) System . . . . . . . . . . . . 301

▫ Rear Manual Climate Control Zone — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 308

▫ Automatic Temperature Control (ATC) — If

Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 310
▫ Summer Operation . . . . . . . . . . . . . . . . . . . 318

▫ Winter Operation . . . . . . . . . . . . . . . . . . . . . 319
▫ Vacation/Storage . . . . . . . . . . . . . . . . . . . . . 319
▫ Window Fogging . . . . . . . . . . . . . . . . . . . . . 319
▫ Outside Air Intake . . . . . . . . . . . . . . . . . . . . 319
▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . 320
▫ A/C Air Filter— If Equipped . . . . . . . . . . . . 320

INSTRUMENT PANEL FEATURES

UNDERSTANDING YOUR INSTRUMENT PANEL 233

1 - Air Vent 2 - Instrument Cluster 3 - Shift Lever 4 - Radio

5 - Storage Bin 6 - Upper Glove Compartment 7 - Lower Glove Compartment 8 - Climate Controls

9 - Storage or DVD 10 - Cup Holders 11 - Storage Bin 12 - Power Supply – 12V

13 - Hazard Switch 14 - Ignition Switch 15 - Dimmer Switch 16 - Headlight Switch

234 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTER – BASE

INSTRUMENT CLUSTER – PREMIUM