2010 Chrysler TOWN and Country Owners Manual

Turn Signals

If either light remains on and does not flash, or NOTE: there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, the indicator bulb is defective.

it would suggest

that

166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. Turn Signal Warning If the vehicle electronics sense that the vehicle has traveled at over 18 mph (29 km/h) for approximately 1 mile (1.6 km) with the turn signals on, a chime will sound to alert the driver. High/Low Beam Switch When the headlights are turned on, pushing the multi- function lever toward the instrument panel will switch from low beams to high beams. Pulling back to the neutral position returns the headlights to the low beam operation.

Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will turn on the high beam headlights until the lever is released. SmartBeam™ — If Equipped The SmartBeam™ system provides increased forward lighting at night by automating high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera detects vehicle spe- cific light and automatically switches from high beams to low beams until the approaching vehicle is out of view. To Activate 1. Select “Automatic High Beams — ON” through the EVIC. Refer to “Electronic Vehicle Information Center (EVIC)/Customer-Programmable Features” in “Under- standing Your Instrument Panel” for further information.

2. Rotate the headlight switch counterclockwise to the AUTO (A) position. 3. Push the multifunction lever away from you to switch the headlights to the high beam position. Refer to “Mul- tifunction Lever” in this section for further information. NOTE: This system will not activate until the vehicle is at, or above, 25 mph (40 km/h). To Deactivate Perform either of the following steps to deactivate the SmartBeam™ system. 1. Pull the multifunction lever toward you to switch the headlights from the high beam to the low beam position. 2. Rotate the headlight switch clockwise from the AUTO (A) to the on position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167
NOTE: Broken, muddy or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film and other obstructions on the windshield or camera lens will cause the system to function improperly.

WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch within the multifunction lever. Rotate the end of the multifunc- tion lever to select the desired wiper speed.

168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Always remove any buildup of snow that pre- vents the windshield wiper blades from returning to the off position. If the windshield wiper switch is turned off and the blades cannot return to the off position, damage to the wiper motor may occur.

Washer And Wiper Controls

1 — Front Mist/Washer 2 — Wiper Speeds

3 — Rear Wiper/Washer

1. Mist, Front Wiper and Washer Press the end of the multifunction lever inward to the first detent and release to clear the windshield. Pressing the multifunction lever inward to the second detent will cause the washers to spray for a maximum of 10 seconds, or until the multifunction lever is released, and the wipers will cycle three times. NOTE: • If the multifunction lever is pressed while in the delay range, the wipers will operate for several seconds after the multifunction lever is released, and then resume the intermittent interval previously selected. • If the multifunction lever is pressed while in the off position, the wipers will operate for approximately two or three wipe cycles and automatically turn off.

2. Intermittent, Low and High Speed Wipers Use the intermittent wipers when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Rotate the end of the multifunc- tion lever to the first detent position, then turn the end of the multifunction lever to select the desired delay inter- val. The delay can be regulated from approximately two seconds, to a maximum of 20 seconds between cycles. The time delay will be doubled if the vehicle speed is less than 10 mph (16 km/h). Low-speed is achieved by rotating the multifunction lever past the intermittent settings, to the first detent. High-speed is achieved by rotating the multifunction lever past the intermittent settings, to the second detent.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169

3. Rear Wiper and Washer Rotating the rotary ring to the first detent activates the rear intermittent wipers. To activate the washers, rotate the rotary ring fully forward and the washers will spray until the ring is released, and then resume the intermit- tent interval. NOTE: Rear window wipers function in the intermittent wiper speed only.

WARNING!

Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.

170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. This feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of the five intermittent wiper sensitivity settings to activate this feature. The sensitivity of the system is adjustable from the multifunction lever. Wiper sensitivity position 3 has been calibrated for best overall wiping sensitivity. If the opera- tor desires more wiping sensitivity, they may select sensitivity positions 4 or 5. If the operator desires less wiping sensitivity, they may select sensitivity positions 2
or 1. Place the multifunction lever in the OFF position when not using the system.

wiper speed is in the low or high position.

NOTE: • The Rain Sensing feature will not operate when the • The Rain Sensing feature may not function properly when ice or dried saltwater is present on the wind- shield. • Use of Rain-X威 or products containing wax or silicone • The Rain Sensing feature can be turned on and off through the EVIC (if equipped). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Understand- ing Your Instrument Panel” for further information.

may reduce rain sensor performance.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171

• Remote Start Mode Inhibit — On vehicles equipped with Remote Starting system, Rain Sensing wipers are not operational when the vehicle is in the remote start mode. Once the operator is in the vehicle and has placed the ignition switch in the RUN position, rain sensing wiper operation can resume, if it has been selected, and no other inhibit conditions (mentioned previously) exist.

TILT STEERING COLUMN This feature allows you to tilt the steering column upward or downward. The tilt control lever is located on the steering column, below the steering wheel.

The Rain Sensing system has protective features for the wiper blades and arms. It will not operate under the following conditions: • Low Temperature Wipe Inhibit — The Rain Sensing feature will not operate when the ignition is first switched ON, and the vehicle is stationary, and the outside temperature is below 32°F (0°C), unless the wiper control on the multifunction lever is moved, or the vehicle speed becomes greater than 0 mph (0 km/h), or the outside temperature rises above freezing. • Neutral Wipe Inhibit — The Rain Sensing feature will not operate when the ignition is ON, and the trans- mission shift lever is in the NEUTRAL position, and the vehicle speed is less than 5 mph (8 km/h), unless the wiper control on the multifunction lever is moved or the shift lever is moved out of the NEUTRAL position.

172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To tilt the column, push the lever downward to the unlocked position. Move the steering column up or down, as desired. Pull the lever upward to the locked position to lock the steering column firmly in place.

Tilt Steering Column Lever

1 — Locked Position 2 — Unlocked Position

WARNING!

Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle. Failure to follow this warning may result in serious injury or death.

ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward, or away, from the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat positions. The switch is located on the left side of the steering column.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173

• The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control Sys- tem is on. The following messages will be displayed on vehicles equipped with the Electronic Vehicle In- formation System (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjust- able Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”.

CAUTION!

Do not place any article under the adjustable pedals or impede its ability to move, as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path.

Adjustable Pedal Switch

Press the button forward to move the pedals forward (toward the front of the vehicle). Press the button rearward to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF.

174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident. Always adjust the pedals while the vehicle is parked.

ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h).

Electronic Speed Control Lever

In order to ensure proper operation, the Elec- NOTE: tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control

System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button (located in the end of the lever) once, and the cruise indicator light (located in the mes- sage window of the odometer) will illuminate, showing that the Electronic Speed Control system is on. To turn the Electronic Speed Control system off, push the ON/ OFF button a second time, and both the Electronic Speed Control system and indicator will turn off.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175

WARNING!

Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the Electronic Speed Control system off when you are not using it.

To Set At A Desired Speed Turn the Electronic Speed Control ON. When the vehicle has reached the desired speed, press the SET lever downward and then release. Lift your foot off the accel- erator and the vehicle will operate at the selected speed.

176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Deactivating Electronic Speed Control A soft tap on the brake pedal or pulling the Electronic Speed Control lever (CANCEL) toward you will deacti- vate the Electronic Speed Control without erasing the set speed memory. Pushing the ON/OFF button to the OFF position or turning OFF the ignition erases the set speed memory. Resuming Speed To resume a previously set speed, raise the Electronic Speed Control lever (RESUME ACCEL) upward, and release. Resume can be used at any speed above 25 mph (40 km/h). Varying The Speed Setting When the Electronic Speed Control is set, you can in- crease speed by pushing up and holding the RESUME ACCEL lever. If the lever is continually held in the

RESUME ACCEL position, the set speed will continue to increase until the lever is released, then the new set speed will be established. Tapping the Electronic Speed Control lever to RESUME ACCEL once will result in a 1 mph (1.6 km/h) speed increase. Each time the lever is tapped speed increases, so tapping the lever three times will increase speed by 3 mph (4.8 km/h), etc. To decrease speed while Electronic Speed Control is set, push down and hold the Electronic Speed Control lever in SET DECEL. If the lever is continually held in the SET DECEL position, the set speed will continue to decrease until the lever is released. Release the lever when the desired speed is reached, and a new set speed will be established. Tapping the Electronic Speed Control lever to SET DE- CEL once will result in a 1 mph (1.6 km/h) speed decrease. Each time the lever is tapped, speed decreases.

Accelerating To Pass Press the accelerator as you normally would. When the pedal is released, the vehicle will return to the set speed. NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal. Your vehicle may experience a downshift (automatic transmissions only) while climbing uphill or descending downhill. This downshift is necessary to maintain vehicle set speed. On steep hills, a greater speed loss or gain may occur, so it may be preferable to drive without Electronic Speed Control.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177

WARNING!

Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.

PARKSENSE姞 REAR PARK ASSIST — IF EQUIPPED The ParkSense威 Rear Park Assist system provides visual and audible indications of the distance between the rear fascia and the detected obstacle when backing up. Refer to ParkSense威 System Usage Precautions for limitations of this system and recommendations.

178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense威 will remember the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the RUN/ON position. ParkSense威 can be active only when the shift lever is in REVERSE. If ParkSense威 is enabled at this shift lever position, the system will be active until the vehicle speed is increased to approximately 11 mph (18 km/h) or above. The system will be active again if the vehicle speed is decreased to speeds less than approximately 10 mph (16 km/h). ParkSense姞 Sensors The ParkSense威 sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is within the sensors’ field of view.

The sensors can detect obstacles from approximately 12 in (30 cm) up to 79 in (200 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle. ParkSense姞 Warning Display The ParkSense威 Warning screen will only be displayed if Sound and Display is selected from the Customer- Programmable Features section of the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer- Programmable Features)” in “Understanding Your In- strument Panel” for further information.

The ParkSense威 Warning Display is located in the Instru- ment cluster’s EVIC display. It provides both visual and audible warnings to indicate the distance between the rear fascia/bumper and the detected obstacle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179

ParkSense姞 Display When the vehicle is in REVERSE, the warning display will turn ON indicating the system status.

ParkSense威 Warning Display

Park Assist ON

180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

The system will indicate a detected obstacle by showing three solid arcs and will produce a 1⁄2 second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.

Park Assist Disabled

Slow Tone

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181

Fast Tone

Continuous Tone

The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone. The following chart shows the warning display operation when the system is detecting an obstacle:

182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING DISPLAY DISTANCES

DISPLAY MESSAGE

OBSTACLE DISTANCE FROM:

ARC’s

AUDIBLE SIGNAL

Park Assist ON

Warning Object Detected Warning Object Detected Warning Object Detected Warning Object Detected Warning Object Detected Warning Object Detected Warning Object Detected

REAR CORNERS

REAR CENTER

27.5 in (70 cm) 25.5 in (65 cm) 19.7 in (50 cm) 15.7 in (40 cm) 11.8 in (30 cm)

78.7 in (200 cm) 39.3 in (100 cm) 31.4 in (80 cm) 25.5 in (65 cm) 19.7 in (50 cm) 15.7 in (40 cm) 11.8 in (30 cm)

None 3 Solid

3 Flashing 3 Flashing 2 Flashing 2 Flashing 2 Flashing 1 Flashing

None

Yes, 1/2 second

Slow Tone Slow Tone Fast Tone Fast Tone Fast Tone

Continuous Tone

NOTE: ParkSense威 will MUTE the radio, if on, when the system is sounding an audio tone.

Enabling/Disabling ParkSense姞 You can turn ParkSense威 ON or OFF through the EVIC. The available choices are: OFF, Sound Only, or Sound and Display. Refer to “Electronic Vehicle Information Center

(EVIC)/Personal Settings (Customer-Programmable Fea- tures)” in “Understanding Your Instrument Panel” for further information. As soon as the system is disabled, the instrument cluster will display the “PARK ASSIST DISABLED” message,

refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further in- formation. When the shift lever is moved to REVERSE and the system is disabled, the EVIC will display the “PARK ASSIST DISABLED” message for as long as the vehicle is in REVERSE. Service ParkSense姞 When the ParkSense威 system is malfunctioning, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the “SERVICE PARK ASSIST SYSTEM” message. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. When the shift lever is moved to REVERSE and the system has detected a faulted condition, the EVIC will display the “SERVICE PARK ASSIST SYSTEM” message for as long as the vehicle is in REVERSE. Under this condition ParkSense威 will not operate.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183
If “SERVICE PARK ASSIST SYSTEM” appears in the Electronic Vehicle Information Center (EVIC) after mak- ing sure the rear fascia/bumper is free from snow, ice, mud, dirt and debris, see your authorized dealer. Cleaning ParkSense姞 Clean the ParkSense威 sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could dam- age the sensors. ParkSense姞 System Usage Precautions NOTE: • Ensure that the rear bumper is free of dirt and debris to keep the ParkSense威 Rear Park Assist system oper- ating properly. • Jackhammers, large trucks, and other vibrations could

affect the performance of the ParkSense威 system.

184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

• When you turn ParkSense威 off, the instrument cluster will display “PARK ASSIST DISABLED.” Further- more, once you turn ParkSense威 off, it remains off until you turn it on again, even if you cycle the ignition key. • When you move the shift lever to the REVERSE position and ParkSense威 is turned off, the instrument cluster will display “PARK ASSIST DISABLED” mes- sage for as long as the vehicle is in REVERSE. • ParkSense威, when on, will MUTE the radio when it is • If a ParkSense威 system malfunction occurs, a single chime will sound once per ignition cycle. In addition, the Electronic Vehicle Information Center (EVIC) will display “SERVICE PARK ASSIST SYSTEM”. If this occurs making sure the rear fascia/bumper is free from snow, ice, mud, dirt and debris, see your autho- rized dealer.

sounding a tone.

• Clean the ParkSense威 sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt, or debris. Failure to do so can result in the ParkSense威 system not working properly. The ParkSense威 system might not detect an obstacle behind the fascia/bumper, or it could provide a false indication that an obstacle is behind the fascia/bumper. • Objects must not be within 12 in (30 cm) from the rear fascia/bumper while driving the vehicle. Failure to do so can result in the system misinterpreting a close object as a sensor problem, causing the “SERVICE PARK ASSIST SYSTEM” message to be displayed in the instrument cluster.

CAUTION!

• ParkSense威 is only a parking aid and it is unable to recognize every obstacle, including small ob- stacles. Parking curbs might be temporarily de- tected or not detected at all. Obstacles located above or below the ParkSense威 sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using ParkSense威 to be able to stop in time when the obstacle is detected. It is recommended that the driver looks over his/her shoulder when using ParkSense威.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185

WARNING!

• Drivers must be careful when backing up even when using the ParkSense威 Rear Park Assist sys- tem. Always check carefully behind your vehicle, look behind you, and be sure to check for pedes- trians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.

(Continued)

186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING! (Continued)

• Before using the ParkSense威 Rear Park Assist system, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns on the single flashing arc and sounds the continuous tone. Also, the sensors could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle.

PARKVIEW姞 REAR BACK UP CAMERA — IF EQUIPPED Your vehicle may be equipped with the ParkView威 Rear Back Up Camera that allows you to see an on-screen image of the rear of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed on the Navigation/Multimedia radio display screen. The Park- View威 camera is located in the light bar over the rear license plate.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187

CAUTION! (Continued)

• To avoid vehicle damage, the vehicle must be driven slowly when using ParkView威 to be able to stop in time when an obstacle is seen. It is recom- mended that the driver look frequently over his/ her shoulder when using ParkView威.

If snow, ice, mud, or anything else builds up on NOTE: the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens.

WARNING!

Drivers must be careful when backing up even when using the ParkView威 Rear Back Up Camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.

CAUTION!

• To avoid vehicle damage, ParkView威 should only be used as a parking aid. The camera is unable to view every obstacle or object in your drive path.

(Continued)

188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning ParkView姞 On or Off — With Navigation/Multimedia Radio

1. Press the “menu” hard key. 2. Select ⬙system setup⬙ soft key. 3. Press the “camera setup” soft key. 4. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key. 5. Press the “save” soft key. 6. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with a caution note to “check entire surroundings” displayed across the top of the screen. After five seconds this note will disappear. 7. When the vehicle is shifted out of REVERSE, the rear camera mode is exited and the navigation or audio screen appears again.

Turning ParkView姞 On or Off — Without Navigation/Multimedia Radio

1. Press the “menu” hard key. 2. Select “system setup” soft key. 3. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key. 4. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with a caution note to “check entire surroundings” displayed across the top of the screen. After five seconds this note will disappear. 5. When the vehicle is shifted out of REVERSE, the rear camera mode is exited and the audio screen appears again.

OVERHEAD CONSOLES

Front Overhead Console Two versions of the overhead console are available. The base front overhead console model featured fixed incan- descent courtesy/reading lights, flip-down sunglass stor- age and conversation mirror. The premium front over- head console model features a LED focused light that illuminates the instrument panel cupholders, Infrared Automatic Temperature Control Sensor (ATC equipped only), two swiveling LED lights, flip-down sunglass storage, conversation mirror, optional power sliding door switches and an optional power liftgate switch. NOTE: Premium sunroof console models include all of above except sunglass storage.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189

Front Premium Overhead Console Features

4 — Storage/Mirror 5 — Switch Bank

1 — Cupholder LED 2 — ATC Sensor 3 — Interior Lights Courtesy/Interior Lighting At the forward end of the console are two courtesy lights (standard dome light has two buttons). The lights turn on

190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle. Press a second time to turn each light off. You may adjust the direction of these lights by pressing the outside ring, which is identified with four directional arrows (LED lamps only). The area around the instrument panel cupholders is also illuminated from a light in the overhead console (pre- mium console only). This light is turned on when the headlight switch is on, and will adjust in brightness when the dimmer control is rotated up or down. Sunglass Storage (non-sunroof only) At the rear of the front overhead console, a compartment is provided for the storage of two pairs of sunglasses.

From the closed position, press the door over-travel latch to open the compartment. The door will slowly rotate to the full open position. From this position, the door can be fully closed or, by rotating upward about 3/4 of the way and releasing, positioned for conversation mirror use. From the ⬙conversation mirror⬙ position, the door can only be closed. To return to the full open position, the door must first be closed and then opened by pressing the over-travel latch again to release. NOTE: The front overhead console supplied with fac- tory sunroof, incorporates a sunroof switch. Rear Overhead Consoles — If Equipped The rear overhead storage system is available in two versions: with or without sunroof. An additional LED at the front of the rear console shines down on the front foot-well area while in courtesy mode, for added convenience.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191

Rear Courtesy/Reading Lights — If Equipped The overhead console has two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE) the lights will also turn on when the UNLOCK button on the RKE transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle. Press the lens a second time to turn each light off. You may adjust the direction of these lights by pressing the outside ring, which is identified with four directional arrows.

Overhead Compartment Features

1 — DVD 1
2 — Rear HVAC 3 — Interior Lights 4 — Storage 1 If equipped, otherwise storage.

5 — Storage 6 — DVD 1
7 — Interior Lights 8 — Halo Lighting

192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Console Halo Lighting The rear overhead console has recessed halo lighting around the perimeter of the console base. This feature provides additional lighting options while traveling and is controlled by the headlight switch. Refer to “Lights/ Halo Lights — If Equipped” in “Understanding the Features Of Your Vehicle” for further information.

GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink威 unit operates off your vehicle’s battery. The HomeLink威 buttons that are located in the headliner or sun visor designate the three different HomeLink威 channels.

HomeLink威 Buttons

NOTE: HomeLink威 is disabled when the Vehicle Secu- rity Alarm is active.

WARNING!

• Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for safety infor- mation or assistance. • Vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause serious injury or death.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193

Programming HomeLink姞

Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for up to 20 seconds until the red indicator flashes. It is recommended that a new battery be placed in the handheld transmitter of the device that is being copied to HomeLink威 for more efficient training and accurate transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage when programming. Begin Programming 1. Turn the ignition switch to the ON/RUN position. 2. Hold the battery side of the handheld transmitter away from the HomeLink威 button you wish to program.

194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Place the handheld transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink威 button you wish to program while keeping the indicator light in view. 3. Simultaneously press and hold both the chosen HomeLink威 button and the handheld transmitter button until the HomeLink威 indicator changes from a slow to a rapidly blinking light, then release both the HomeLink威 and handheld transmitter buttons. Watch for the HomeLink威 indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds or longer in rare cases. The garage door may open and close while you train. NOTE: • Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section.

• After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the ga- rage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, proceed to Step 5 “Programming A Rolling Code System.”

4. Press and hold the just-trained HomeLink威 button and observe the indicator light. If the indicator light stays on constantly, programming is complete and the garage door (or device) should activate when the HomeLink威 button is pressed. If the indicator light blinks rapidly for two seconds and then turns to a constant light, proceed to Step 5 “Pro- gramming A Rolling Code System.” 5. Programming A Rolling Code System At the garage door opener motor (in the garage), locate the “Learn” or “Training” button.

This can usually be found where the hanging antenna wire is attached to the garage door opener motor. It is NOT the button normally used to open and close the door.

Training The Garage Door Opener

1 — Door Opener 2 — Training Button

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195
6. Firmly press and release the LEARN or TRAINING button. The name and color of the button may vary by manufacturer. NOTE: You have 30 seconds in which to initiate the next step after the LEARN button has been pressed. 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. To program the remaining two HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels.

and release

196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink威 To operate, press the programmed HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The handheld transmitter of the device may also be used at any time. Reprogramming a Single HomeLink威 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button, proceed with Program- ming HomeLink威 Step 2 and follow all remaining steps.

Gate Operator/Canadian Programming Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace “Programming HomeLink威” Step 3, with the following: 3. Continue to press and hold the HomeLink威 button, while you press and release (“cycle”), your handheld transmitter every two seconds until HomeLink威 has

successfully accepted the frequency signal. The indica- tor light will flash slowly and then rapidly when fully trained. If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Programming HomeLink威,” earlier in this section. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The HomeLink威 Universal Transceiver is disabled when the Vehicle Security Alarm is active.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197

Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the LEARN button on the Garage Door Opener • Did you unplug the device for training, and remember

to complete the training for a Rolling Code.

to plug it back in?

If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference.

198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for com- pliance could void the user’s authority to operate the device. • The term IC before the certification/registration num- Industry Canada technical

ber only signifies that specifications were met.

POWER SUNROOF — IF EQUIPPED The power sunroof control switch is located in the front overhead console. The sunroof panel tilts upward at the rear for ventilation or slides rearward under the roof.

Power Sunroof Operation

Opening the Sunroof Manually Press the switch rearward and hold, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. During this opera- tion, any release of the sunroof switch will stop the sunroof.

WARNING!

In an accident, there is greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured.

Closing the Sunroof Manually To close the sunroof from an open or vent position, press and hold the switch forward. The sunroof will close fully and stop automatically. Release the switch to stop sun- roof travel at any point. Sunroof Sunshade Operation The sunroof sunshade can be opened manually. How- ever, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199

WARNING!

Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sun- roof while operating the power sunroof switch. Such entrapment may result in serious injury or death.

Express Open Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Express Vent Press and release the ⬙V⬙ button, and the sunroof will automatically open to the vent position. This is called “Express Vent”.

200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Express Close Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully, then stop automatically. This is called “Express Close”. During Express Close operation, any movement of the sunroof switch will stop the sunroof.

WARNING!

Do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object to project through the sunroof opening. Injury may result.

Ignition Off Operation The power sunroof switch will remain active for 10 min- utes after the ignition switch is turned OFF. Opening either front door will cancel this feature.

Auto-Express with Anti-Pinch Protection During express closing, anytime an obstacle that restricts glass movement is detected, the motor will stop and reverse travel to avoid pinching the object. Auto Express will stop and reverse travel up to three times in succession. After the third time, Auto Express will enter a manual operation mode. This allows the operator to manually control the power switch, in order to close or open the sunroof in case of a malfunction. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs

with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel.

ELECTRICAL POWER OUTLETS — IF EQUIPPED Two 12 Volt (13 Amp) power outlets are located on the lower instrument panel, next to the open storage bin. The upper power outlet is controlled by the ignition switch and the lower power outlet is connected directly to the battery. The upper power outlet will also operate a conventional cigar lighter unit (if equipped with an optional Smoker’s Package). NOTE: • To ensure proper operation a MOPAR威 cigar knob and

element must be used.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201

• Do not exceed the maximum power of 160 Watts (13
Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced.

12 Volt Power Outlets

202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE One outlet in the removable floor console shares a fuse with the lower outlet in the instrument panel and is also connected to the battery. Do not exceed a maximum power of 160 Watts (13 Amps) shared between the lower panel outlet and the removable floor console outlet. The outlet in the rear quarter panel near the liftgate and the upper outlet in the instrument panel are both con- trolled by the ignition switch. Each of these outlets can support 160 Watts (13 Amps). Do not exceed 160 Watts (13 Amps) for each of these outlets. The power outlets include tethered caps, labeled with a key or battery symbol indicating the power source. The power outlet, located on the lower instrument panel, is powered directly from the battery. Items plugged into this power outlet may discharge the battery and/or prevent the engine from starting.

WARNING!

To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving • If this outlet is mishandled, it may cause an

the vehicle.

electric shock and failure.

CAUTION!

• Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly. Only use these inter- mittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery.

(Continued)

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203

CAUTION! (Continued)

• Power outlets are designed for accessory plugs only. Do not hang any type of accessory or acces- sory bracket from the plug. Improper use of the power outlet can cause damage.

POWER INVERTER — IF EQUIPPED A 110 Volt, 150 Watt inverter outlet (if equipped) converts DC current to AC current, and is located on the left rear trim panel immediately behind the second row left passenger seat. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Playstation3 and XBox360 will exceed this power limit, as will most power tools.

204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter may have to be reset manually. To reset the inverter manually press the power inverter button OFF and ON. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter.

Power Inverter Outlet

The power inverter switch is located near the center of the instrument panel below the two 12 Volt power outlets.

To turn on the power outlet, press the switch once. Press the switch a second time to turn the power outlet off.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205

CUPHOLDERS There are nine cupholders in the interior. Two cupholders in the center front instrument panel, four in the floor consoles and three more are located in the third row quarter trim panel. All liners are removable for cleaning. Pull the flexible liner from the cupholder drawer or tray starting at one edge for easy removal. Refer to “Cleaning The Instru- ment Panel Cupholders” in “Maintaining Your Vehicle” for further information.

Power Inverter Switch

206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Instrument Panel Cupholders The instrument panel cupholders are located in a pull-out drawer just above the lower storage bin.

Front Cupholders

Pull the drawer out firmly until it stops, and place the container to be held in either one of the cupholder wells. The cupholders are designed to accommodate a wide

variety of container types and sizes. Press down on the container to engage the cupholder retention features. Interior Bottle Holders There are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel. Each holder accommo- dates up to a 20 oz (.6 L) plastic bottle.

WARNING!

If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burn- ing the occupants. Be careful when closing the doors to avoid injury.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207
of the two cupholders in the center front instrument panel. To install the ash receiver, align the receiver so the thumb grip on the lid is facing rearward. Press the ash receiver into either of the cup wells to secure. Pull upward on the ash receiver to remove for cleaning and/or storage. The left rear trim panel cupholder is designed to accom- modate a second ash receiver, if desired.

STORAGE

Glove Compartments

Upper Glove Compartment To open the upper compartment, press inward on the release button (2). The door will spring open about 1 in (2.54 cm). Manually lift the front edge of the door upward, until fully opened, and the detent is engaged.

Interior Bottle Holder

Two outboard mesh pockets are on intermediate seating. The mesh pockets are flexible enough to hold juice boxes, toys, games or MP3 players, etc. Smoker’s Package Kit — If Equipped With the optional authorized dealer-installed Smoker’s Package Kit, a removable ash receiver is inserted into one

208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To close the compartment door, push firmly downward on the door’s surface to release the detent and latch the door closed.

Lower Glove Compartment To open the lower compartment, pull out on the release handle (3). The lower compartment handle is also equipped with a lock (3).

Glove Compartment Features

1 — Upper Compartment 2 — Upper Latch

3 — Lower Latch/Lock 4 — Lower Compartment

Door Trim Panel Storage

Front Door Storage Both interior front door panels have multiple pockets for storage.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209

WARNING!

If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burn- ing the occupants. Be careful when closing the doors to avoid injury.

Front Door Storage Features

1 — Storage Pocket 2 — Map Pocket

3 — Bottle Holder 4 — Map Pocket

210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver Seatback Storage — If Equipped The drivers seatback has a primary storage pocket on all models and an optional secondary mesh pocket.

Umbrella Holder An umbrella holder has been conveniently molded into the left front door entry scuff molding.

Driver’s Seatback Storage

Umbrella Holder

1 — Bag Holder 2 — Standard Pocket 3 — Mesh Pocket

Second Row Floor Storage Bins The area below the floor covers, located in front of the second row seats, is available for storage.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211

CAUTION!

The storage bin cover must lay flat and be locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.

WARNING!

covers open.

In an accident, serious injury could result if the seat storage bin covers are not properly latched. • Do not drive the vehicle with the storage bin • Keep the storage bin covers closed and latched • Do not operate the storage bin covers while the • Do not use a storage bin latch as a tie down.

while the vehicle is in motion.

vehicle is in motion.

Storage Bin Cover Lock Release

Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the ⬙unlocked⬙ position to allow greater access to the storage bin.

212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage Bin Safety Warning Carefully follow these warnings to help prevent personal injury or damage to your vehicle:

WARNING!

vehicle is unattended.

• Always close the storage bin covers when your • Do not allow children to have access to the second row seat storage bins. Once in the storage bin, young children may not be able to escape. If trapped in the storage bin, children can die from suffocation or heat stroke. • In an accident, serious injury could result if the seat storage bin covers are not properly latched. • Do not drive the vehicle with the storage bin covers open. Keep the storage bin covers closed and latched while the vehicle is in motion.

(Continued)

WARNING! (Continued)

• Do not operate the storage bin covers while the • Do not use a storage bin latch as a tie down.

vehicle is in motion.

CAUTION!

The storage bin cover must be flat and locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.

Seat Storage Bin Cover Emergency Release Lever As a security measure, your vehicle may be built with a Storage Bin Cover Emergency Release is built into the storage bin cover latching mechanism.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213
In the event of an individual being locked inside NOTE: the storage bin, the storage bin cover can be opened from inside of the bin by pushing on the glow-in-the-dark lever attached to the storage bin cover latching mechanism. Center And Rear Overhead Console Storage — If Equipped The overhead storage system comes in several options.

Storage Bin Cover Emergency Release Lever

214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Overhead Console Features

1 — DVD 1
2 — Rear HVAC 3 — Courtesy Lights 4 — Storage 1 If equipped, otherwise storage.

5 — Storage 6 — DVD 1
7 — Courtesy Lights 8 — Halo Lighting

Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle. Cargo Area Storage The liftgate sill plate has a raised line with the statement “Load To This Line”. This line indicates how far rearward cargo can be placed without interfering with liftgate closing.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215

easily pass through the first row to the second.

Basic Console Basic Console features consist of the following: • The basic console profile allows vehicle occupants to • Four cupholders accept up to extra large size beverage cups or 20 oz (.6 L) plastic bottles. Cupholders are dishwasher safe for cleaning. • The cupholders are removable to access a large storage • The basic console is removable from the vehicle for additional floor space by removing the cap and clip at the console base.

bin.

To Remove The Basic Floor Console 1. Remove the front anchor cup plug and clip. 2. Slide the console base forward while lifting slightly to clear the rear load floor hook.

Rear Cargo Area Loading Limit

NOTE: With all rear seats stowed or removed, 4 x 8foot sheets of building material will fit on the vehicle floor with the liftgate closed. The front seats must be moved slightly forward of the rearmost position.

CONSOLE FEATURES There are two consoles available: Basic and Premium.

216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Remove the console. To Reinstall The Basic Floor Console 1. Position the console at a slight angle (front slightly higher than the rear). 2. Slide the console rearward into the floor bracket/ hook. 3. Align the console until the front anchor cup plug hole is centered on the winch hole. 4. Reinstall the clip first and then while pushing down- ward on the console with slight pressure, reinstall the cover plug. 5. Pull up on the console to be sure it is firmly latched.

WARNING!

In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.

Premium Console — If Equipped The three-compartment console with sliding storage bin, sliding upper tray with storage and large console storage bin offers multiple configurations. • Four cupholders with dishwasher safe liners for clean- ing. The cupholders can accept plastic bottles, large cups or mugs with handles.

• Top tray storage • Upper storage bin can hold nine regular or 18 thin CDs

or other items

• Large console center storage will store headphones for the available rear DVD entertainment system or other items • 12 Volt DC power outlet provides continuous power inside the console for cell phones or other electronics. • Rear occupant accessible • Multiple adjustments • Removable from vehicle for additional floor space.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217

Premium Console Features

1 — Top Release 2 — Center Release The top and center console sections slide forward and rearward to provide added user comfort. A one-piece cup

3 — Console Release

218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE holder insert for both cavities can easily be removed for cleaning. The cupholders will also accommodate large size cups and 20 oz (.6 L) bottles. Position 1 shows the console closed with four cupholders and a convenient storage tray.

Position 2 shows the raised storage tray revealing a large storage area below.

Console Position 1

Console Position 2

Dual Storage Bins Position 3 shows the top portion of the console in a rearward position. This is accomplished by lifting the upper most latch at the front of the console. This provides

easy access to the storage area below and provides two of the four cupholders for the second row passengers.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219

Console Position 4

Console Position 3

Position 4 shows the complete console in its rearmost position. Again, lifting second latch handle at the front of the console, allows complete access to a lower storage bin and provides additional cupholders for rear passengers.

To Remove The Premium Floor Console 1. Pull up on the bottom release handle in the front of the console. 2. Lift centimeters.

the console up several

the rear of

inches/

220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull rearward to disengage from floor and remove console. To reinstall the console: 1. Position the console at a slight angle (rear slightly higher than the front). 2. Slide the console forward into the floor bracket. 3. Rotate the rear of the console down until it is resting on the floor bracket. 4. Push down on the rear of the console until it is seated in the rear floor bracket. 5. Pull up on the console to be sure it is firmly latched.

WARNING!

In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.

REAR WINDOW FEATURES

Rear Window Defroster

The rear window defroster button is located on the climate control (Mode) knob. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after ap- proximately 10 minutes. For an additional five minutes of operation, press the button a second time.

NOTE: • You can turn off the heated mirror feature at anytime by pressing the rear window defroster switch a second time. • To prevent excessive battery drain, use the rear win-

dow defroster only when the engine is operating.

CAUTION!

Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water.

(Continued)

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221

CAUTION! (Continued)

• Do not use scrapers, sharp instruments, or abra- sive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window.

LOAD-LEVELING SYSTEM The automatic load-leveling system will provide a level riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6 km) of driving for the leveling to complete depending on road surface conditions. If the leveled vehicle is not moved for approximately 15 hours, the leveling system will bleed itself down. The vehicle must be driven to reset the system.

222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and side rails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity. To move the crossbars, loosen the thumb screws located at the upper edge of each crossbar approximately six turns, then move the crossbar to the desired position, keeping the crossbars parallel to the rack frame. Once the crossbar is in place, retighten the thumb screws to lock the crossbar into position.

Crossbar

Attempt to move the crossbar again to ensure that it has properly locked into position.

NOTE: To help control wind noise when installing the crossbars ensure the embossed arrow is facing the front of the vehicle. When the crossbars are not in use, the front crossbar should be fastened just forward of the middle support and the rear crossbar should be fastened at the rearmost position of the side rails. This will help reduce the amount of wind noise when the crossbars are not in use. The tie down holes on the crossbar ends should always be used to tie down the load. Check the straps frequently to be sure that the load remains securely attached.

CAUTION!

• Crossbars should remain equally spaced or paral- lel at any luggage rack position for proper func- tion. Noncompliance could result in damage to the luggage rack, cargo and/or vehicle.

(Continued)

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223

CAUTION! (Continued)

• To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropri- ately. • Long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. • Travel at reduced speeds and turn corners care- fully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift to a load. This is especially true on large flat loads and may result in damage to the cargo or your vehicle.

224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.

SUN SCREENS — IF EQUIPPED Sun screens are available for second and third row seating windows. The screens store in the sill trim panels, and the tops of the windows are equipped with hooks that the sun screens attach to when pulled out.

Sun Screen Retracted

Gently pull up on the tab to raise the sun screen. Continue pulling the sun screen until the tab is near the top of the window.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225

Sun Screen Attaching To Retainer Clips

Once the screen is completely to the top of the window, extend the top bar of the sun screen over the two hooks attached to the top of the window.

Sun Screen Extended

To lower the sun screen, gently lift the tab upward to disengage the hooks, and feed the screen back into the base sill.

UNDERSTANDING YOUR INSTRUMENT PANEL

CONTENTS

䡵 Instrument Panel Features 䡵 Instrument Cluster 䡵 Instrument Cluster Descriptions 䡵 Compass Mini-Trip Computer (CMTC) —

. . . . . . . . . . . . . . . 231
. . . . . . . . . . . . . . . . . . . . 232
. . . . . . . . . . . 233

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 247
▫ CMTC Reset Buttons . . . . . . . . . . . . . . . . . . 247
▫ Compass/Temperature Display . . . . . . . . . . 249

䡵 Electronic Vehicle Information Center (EVIC) —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 250

▫ Electronic Vehicle Information Center (EVIC)

Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
. . . . . . . . . . . . . . . . . . . . . . 254

▫ Trip Functions ▫ Compass Display / ECO (Fuel Saver Mode)

— If Equipped . . . . . . . . . . . . . . . . . . . . . . 256

▫ Personal Settings

(Customer-Programmable Features)

. . . . . . . 258

䡵 Media Center 730N/430 (RER/RBZ) —

AM/FM Stereo Radio And CD/DVD/HDD/ NAV — If Equipped . . . . . . . . . . . . . . . . . . . . 263

228 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions — Voice Command

System (VR) — If Equipped . . . . . . . . . . . . . 263

▫ Operating Instructions — Uconnect™ Phone

— If Equipped . . . . . . . . . . . . . . . . . . . . . . 263
▫ Clock Setting Procedure — RBZ Radio . . . . . 263
▫ Clock Setting Procedure — RER Radio . . . . . 265

䡵 Media Center 130 (RES) — AM/FM Stereo

Radio With CD Player (MP3 AUX Jack). . . . . . . 267
▫ Operating Instructions — Radio Mode . . . . . 268
▫ Operation Instructions — CD Mode For CD

And MP3 Audio Play . . . . . . . . . . . . . . . . . 271
▫ Notes On Playing MP3 Files . . . . . . . . . . . . 273
▫ Operation Instructions - Auxiliary Mode . . . . 276

䡵 Media Center 130 (RES/RSC) — AM/FM

Stereo Radio With CD Player (MP3 AUX Jack) And Sirius Radio . . . . . . . . . . . . . . . . . . . . . . 276
▫ Operating Instructions — Radio Mode . . . . . 277
▫ Operation Instructions — CD Mode For CD

And MP3 Audio Play . . . . . . . . . . . . . . . . . 282
▫ Notes On Playing MP3 Files . . . . . . . . . . . . 284
▫ List Button (CD Mode For MP3 Play) . . . . . . 287
▫ Info Button (CD Mode For MP3 Play) . . . . . . 287

䡵 Universal Consumer Interface (UCI) 0.5 —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 289
▫ Connecting The iPod威 . . . . . . . . . . . . . . . . . 289
▫ Using This Feature . . . . . . . . . . . . . . . . . . . 290
▫ Controlling The iPod威 Using Radio

Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . 290

▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 290
▫ List Or Browse Mode . . . . . . . . . . . . . . . . . 292

䡵 Uconnect™ Multimedia (Satellite Radio) — If Equipped (REN/RER/RBZ/RES Radios Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
▫ System Activation . . . . . . . . . . . . . . . . . . . . 294
▫ Electronic Serial Number/Sirius

Identification Number (ESN/SID) . . . . . . . . . 294

▫ Selecting Uconnect™ Multimedia (Satellite)

Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295
▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . 295
▫ Reception Quality . . . . . . . . . . . . . . . . . . . . 295
▫ Operating Instructions - Uconnect™

Multimedia (Satellite) Mode . . . . . . . . . . . . . 296

UNDERSTANDING YOUR INSTRUMENT PANEL 229

▫ Operating Instructions - Uconnect™ Phone

(If Equipped)

. . . . . . . . . . . . . . . . . . . . . . . 298

䡵 Uconnect™ Multimedia (Sirius Backseat TV™)

— If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 298

䡵 Video Entertainment System (VES)™ —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 298

䡵 Remote Sound System Controls —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 300
▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . 301
▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . 301
䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . 302
䡵 Radio Operation And Cellular Phones . . . . . . . 302
䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 303

▫ Manual Heating And Air Conditioning

System — If Equipped . . . . . . . . . . . . . . . . . 303

230 UNDERSTANDING YOUR INSTRUMENT PANEL

▫ Three-Zone Temperature Control —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 307

▫ Rear Manual Climate Control —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 309

▫ Automatic Temperature Control (ATC) —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 312
▫ Summer Operation . . . . . . . . . . . . . . . . . . . 320

▫ Winter Operation . . . . . . . . . . . . . . . . . . . . 321
▫ Vacation/Storage . . . . . . . . . . . . . . . . . . . . 321
▫ Window Fogging . . . . . . . . . . . . . . . . . . . . 321
▫ Outside Air Intake . . . . . . . . . . . . . . . . . . . 321
▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . 322
▫ A/C Air Filter— If Equipped . . . . . . . . . . . . 322

INSTRUMENT PANEL FEATURES

UNDERSTANDING YOUR INSTRUMENT PANEL 231

1 — Air Vents 2 — Instrument Cluster 3 — Shift Lever 4 — Radio

5 — Analog Clock 6 — Upper Glove Compartment 10 — Cup Holders 7 — Lower Glove Compart- ment 8 — Climate Controls

11 — Storage Bin 12 — Power Supply – 12V

9 — DVD – If Equipped

13 — Switch Bank 14 — Ignition Switch 15 — Dimmer Switch 16 — Headlight Switch

232 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER

INSTRUMENT CLUSTER DESCRIPTIONS

1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. Low Fuel Light

When the fuel level reaches approximately 2.0 gal (7.8 L) this light will turn on, and remain on until fuel is added.

3. Electronic Throttle Control (ETC) Light

This light informs you of a problem with the Electronic Throttle Control (ETC) system. The light will come on when the ignition is first turned ON and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the

UNDERSTANDING YOUR INSTRUMENT PANEL 233
vehicle has completely stopped and the shift lever is placed in the PARK position, the light should turn off. If the light remains lit with the engine running, your vehicle will usually be drivable; however, see an autho- rized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. 4. Charging System Light

This light shows the status of the electrical charg- ing system. The light should come on when the ignition switch is first turned ON and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the

234 UNDERSTANDING YOUR INSTRUMENT PANEL vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an autho- rized dealer. If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”. 5. Tire Pressure Monitoring Telltale Light — If Equipped

Each tire, including the spare (if provided), should be checked monthly, when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System

(TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the

system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.

UNDERSTANDING YOUR INSTRUMENT PANEL 235

CAUTION!

The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can, or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.

236 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Oil Pressure Warning Light

This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood. 7. Engine Temperature Warning Light

This light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches H , this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass H , the indicator will continuously flash and a continuous chime will occur until the engine is allowed to cool.

If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “If Your Engine Overheats” in “What To Do In Emergencies” for further information. 8. Speedometer Indicates vehicle speed. 9. Turn Signal Indicators

The arrow will flash with the exterior turn signal when the turn signal lever is operated.

If the vehicle electronics sense that the vehicle has traveled about 1 mile (1.6 km) with the turn signals on, a continuous chime will sound to alert you to turn the signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb.

10. Electronic Stability Program (ESP) Indicator Light / Brake Assist System (BAS) Warning Light

The malfunction light for the Electronic Stabil- ity Program (ESP) is combined with Brake Assist System (BAS). The yellow “ESP/BAS Warning Light” comes on when the ignition switch is turned to the “ON” position. They should go out with the engine running. If the “ESP/BAS Warning Light” comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible.

UNDERSTANDING YOUR INSTRUMENT PANEL 237

WARNING!

If a warning light remains on the system may not be working and you will not have the benefit of ESP or BAS. Under certain driving conditions, where ESP or BAS would be beneficial, you - if you have not adjusted your driving speeds and stopping in or to account for the lack of the feature, may be in acci- dent.

11. Brake Warning Light

This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.

238 UNDERSTANDING YOUR INSTRUMENT PANEL If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Program (ESP) sys- tem. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.

NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces- sary.

WARNING!

Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately.

Vehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required.

Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approxi- mately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 12. Vehicle Security Light — If Equipped

This light will flash at a fast rate for approxi- mately 15 seconds, when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed.

UNDERSTANDING YOUR INSTRUMENT PANEL 239

13. Anti-Lock Brake (ABS) Light

This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds.

If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not turn on when the Ignition switch is turned to the ON position, have the light inspected by an authorized dealer.

240 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Electronic Stability Program (ESP) Indicator Light / Traction Control System (TCS) Indicator Light

If this indicator light flashes during accelera- tion, apply as little throttle as possible. While driving, ease up on the accelerator. Adapt your speed and driving to the prevailing road con- ditions, and do not switch off the Electronic Stability Program (ESP), or Traction Control System (TCS). 15. Tachometer The red segments indicate the maximum permissible engine revolutions per minute (RPM x 1000) for each gear range. Before reaching the red area, ease up on the accelerator. 16. High Beam Indicator

This indicator shows that the high beam head- lights are on. Push the multifunction lever forward to switch the headlights to high beam, and pull toward yourself (normal position) to return to low beam.

17. Front Fog Light Indicator — If Equipped

This indicator will illuminate when the front fog lights are on.

18. Seat Belt Reminder Light

When the ignition switch is first turned ON, this light will turn on for five to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver’s seat belt remains unbuckled, the Seat Belt Reminder Light will illuminate and the chime will sound. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information. 19. Malfunction Indicator Light (MIL)

The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system, called OBD, that monitors engine and automatic transmission con- trol systems. The light will illuminate when the key is in

the ON position, before engine start. If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the MIL after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require towing.

CAUTION!

Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.

UNDERSTANDING YOUR INSTRUMENT PANEL 241

WARNING!

A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants or wood or cardboard, etc. This could result in death or serious injury to the driver, occu- pants or others.

20. Airbag Warning Light

This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is either not on during starting, stays on, or turns on while driving, then have the system inspected at an authorized dealer as soon as possible. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information.

242 UNDERSTANDING YOUR INSTRUMENT PANEL 21. Temperature Gauge The temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range.

CAUTION!

Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately, and call an authorized deal- ership for service.

WARNING!

A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer- ship for service if your vehicle overheats. If you decide to look under the hood yourself, see “Main- taining Your Vehicle”. Follow the warnings under the Cooling System Pressure Cap paragraph.

22. Odometer / Trip Odometer / ECO (Fuel Saver Indicator) Button — If Equipped Press this button to change the display from odometer to either of two trip odometer settings or the ECO display. The letter “A” or “B” will appear when in the trip odometer mode. Push in and hold the button for two seconds to reset the trip odometer to 0 miles (km). The odometer must be in TRIP mode to reset it.

NOTE: On the Base cluster, the reset button toggles between odometer, Trip A, Trip B, ECO and outside temperature. To reset a message display on Base Cluster (gATE, gASCAP, noFUSE, CHangE OIL, LoCOOL, Lo- WASH, etc.), push and hold the button until the display resets (approximately two seconds). 23. Shift Lever Indicator The Shift Lever Indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. NOTE: You must apply the brakes before shifting from PARK. 24. Message Display Area When the appropriate conditions exist, the following odometer messages will display:

ECO . . . . . . . . . . . . . . . . . . . Fuel Saver Indicator Off