2008 Chrysler TOWN and Country Owners Manual

To open the hood, two latches must be released. 1. Pull the hood release lever located on the instrument panel, below the steering column. 2. Move to the front of the vehicle and look inside the center of the hood opening. Locate then push the safety catch lever to the right while raising the hood at the same time.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157

Hood Release Front View

Hood Safety Catch

Use the hood prop rod to secure the hood in the open position.

158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 12
in (30 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.

WARNING!

If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving.

HOOD SAFETY SWITCH — IF EQUIPPED If the vehicle is equipped with the Electronic Vehicle Information Center (EVIC), and the hood is not latched, the EVIC will display “Hood Ajar” in the instrument cluster EVIC display window. If the vehicle is equipped with the Compass Mini-Trip Computer (CMTC) and the hood is not latched, a “hood” will be displayed in the PRNDL/Odometer window of the instrument cluster.

LIGHTS All of the lights, except the hazard warning lights, headlamp high beams and flash to pass, are controlled by switches to the left of the steering column on the instru- ment panel.

Headlight Switch Assembly

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159

Interior Lighting Interior lights are turned on when a door or liftgate is opened, the keyless entry transmitter is activated, or when the dimmer control is moved to the extreme top. The interior lights will automatically turn off in about 10
minutes for the first activation and 90 seconds every activation thereafter until the engine is started, if one of the following occur: † A door, sliding door or the liftgate is left open † Any overhead reading light is left on † If the dimmer control is in the extreme top position NOTE: The key must be out of the ignition switch or the ignition switch must be in the OFF position for this feature to operate.

160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Dome Light Positions

Rotate the dimmer control completely upward to the second detent (extreme top position) to turn on the interior lights, reading/ courtesy lights. The interior lights will remain on when the dimmer control is in this position.

except

front

the

Parade Mode (Daytime Brightness Feature)

feature brightens

Rotate the dimmer control to the first detent. This the odometer, radio and overhead dis- plays when the park lights or head- lights are on.

Interior Lighting Defeat (Off)

Rotate the dimmer control to the off position (extreme bottom). The inte- rior lights will remain off when the doors or liftgate are open.

Dimmer Control

With the park lights or headlights on, rotating the dimmer control for the interior lights on the instrument panel upward will increase the brightness of the instrument panel lights.

HALO Lights — If Equipped Halo Lights are strategically-placed, soft lighting that helps to illuminate specific areas to aid the occupants in locating specific features while driving at night.

To activate the Halo lights, push in on the Halo switch located below the dimmer control. Pressing the switch in a second time, will turn the Halo lights off.

Exterior Lights

Parking Lights

Turn the headlight switch knob to the first detent to turn the park lights on. This also turns on all

instrument panel lighting.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161

Daytime Running Lights (Canada/Fleet Vehicles Only) The headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except PARK. This provides a constant lights on condi- tion until the ignition is turned OFF. The lights illuminate at less than 50% of normal intensity. If the parking brake is applied the Daytime Running Lights (DRL) will turn off. Also, if a turn signal is activated, the DRL lamp on the same side of the vehicle will turn off for the duration of the turn signal activation. Once the turn signal is no longer active, the DRL lamp will illuminate. Headlights

Turn the headlight switch knob to the 2nd detent to turn the headlights and park lights on. This also turns on all instrument panel lighting.

To change the brightness of the instrument panel lights, rotate the dimmer control up or down.

162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Automatic Headlights — If Equipped This system automatically turns your headlights on or off based on ambient light levels. To turn the system on, turn the headlight switch to the extreme counterclockwise position aligning the indicator with the “A” on the headlight switch. When the system is on, the Headlight Time Delay feature is also on. This means your headlights will stay on for up to 90 seconds after you turn the ignition switch OFF. To turn the Automatic System off, turn the headlight switch clockwise to the “O” off position.

Automatic Headlights

NOTE: The engine must be running before the head- lights will come on in the Automatic mode.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163

The driver can choose, when exiting the vehicle, to have the headlights remain on for 30, 60, or 90 seconds, or not remain on. To change the timer setting see your autho- rized Dealer. If the headlights are turned off before the ignition, they will turn off in the normal manner. NOTE: The headlights must be turned off within 45
seconds of turning the ignition OFF to activate this feature.

Headlights On with Wipers — If Equipped If your vehicle is equipped with Automatic Headlights it also has this customer programmable feature. When your headlights are in the automatic mode, and the engine is running, the headlights will automatically turn on when the wiper system is on. Headlight Delay — If Equipped This feature provides the safety of headlight illumination for up to 90 seconds after exiting your vehicle. To activate the delay feature, turn OFF the ignition switch while the headlights are still on. Then turn off the headlights within 45 seconds. The 90 second delay inter- val begins when headlight switch is turned off. If the headlights or park lights are turned back on or the ignition switch is turned on, the delay will be cancelled.

164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Front Fog Lights — If Equipped

To activate the front fog lights, turn on the park lights or the low beam headlights and push in the headlight switch control knob. Pressing the head- light switch control knob in a second time, will turn the front fog lights off.

Fog Light Switch

Lights-On Reminder If the headlights or the park lights are left on, or if the dimmer control is in the extreme top position after the ignition switch is turned OFF, a chime will sound when the driver’s door is opened. Battery Protection This feature provides battery protection to avoid wearing down the battery if the headlights, park lights, or front fog lights are left on for extended periods of time when the ignition switch is in the LOCK position. After eight minutes of the ignition switch being in the LOCK posi- tion and the headlight switch in any position other than OFF or AUTO, the lights will turn off automatically until the next cycle of the ignition switch or headlight switch. The battery protection feature will be disabled if the ignition switch is turned to any other position other than LOCK during the three minute delay.

MULTIFUNCTION LEVER The multifunction control lever is located on the left side of the steering column. The Multifunction Lever assembly controls: † Turn Signals † Headlight Low and High Beams † Flash-to-Pass (Optical Horn) † Front and Rear Wiper And Washer Functions Turn Signals Move the multifunction lever up or down to signal a right-hand or left-hand turn. The arrow on either side of the instrument cluster flashes to indicate the direction of the turn, and proper operation of the front and rear turn signal lights.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165

If either indicator flashes at a rapid rate, check for a defective outside turn signal light bulb. If one of the indicators fails to light when the lever is moved, it would suggest that the indicator light is defective. You may manually signal a lane change by moving the lever partially up or down.

Turn Signal Switch

166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Turn Signal Auto-Mode Tap the multifunction control lever once and the turn signal (left or right) will flash three times, and automati- cally turn off. Turn Signal Warning If the vehicle electronics sense that the vehicle has traveled at over 18 mph (29 km/h) for about 1 mi (1.6
km) with the turn signals on, a chime will sound to alert the driver. Windshield Wiper and Washer Functions The wipers and washers are operated by a switch within the multifunction lever. Rotate the end of the lever to select the desired wiper speed. NOTE: Always remove any buildup of snow that pre- vents the windshield wiper blades from returning to the off position. If the windshield wiper switch is turned off and the blades cannot return to the off position, damage to the wiper motor may occur.

Multifunction Lever Features

3 - Rear Wiper/Washer 4 - Low/High Beam and Flash

1 - Front Mist/Washer 2 - Wiper Speeds 1. Multifunction Lever — Mist, Front Wiper and Washer Press the end of the multifunction lever inward to the first detent and release to clear the windshield. Pressing

the multifunction lever inward to the second detent will cause the washers to spray for a maximum of 10 seconds, or until the lever is released, and the wipers will cycle three times. If the multifunction lever is depressed while in NOTE: the delay range, the wipers will operate for several seconds after the lever is released, and then resume the intermittent interval previously selected. If the multifunction lever is depressed while in the off position, the wipers will operate for approximately two wipe cycles and automatically turn off. 2. Intermittent, Low and High Speed Wipers Use the intermittent wipers when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Rotate the end of the multifunc- tion lever to the first detent position, then turn the end of the lever to select the desired delay interval. The delay can be regulated from a maximum of about 20 seconds

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167

between cycles, to a cycle every 2 seconds. The time delay will be doubled if the vehicle speed is less than 10 mph (16 km/h). Low Speed is achieved by rotating the multifunction lever past the intermittent settings, to the first detent. High Speed is achieved by rotating the multifunction lever past the intermittent settings, to the second detent. 3. Rotary Ring — Rear Wiper and Washer Rotating the rotary ring to the first detent activates the rear intermittent wipers. To activate the washers, rotate the rotary ring fully forward and the washers will spray until the ring is released, and then resume the intermit- tent interval. NOTE: Rear window wipers function in the intermittent wiper speed only.

168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

4. Headlight Low/High Beam Select Switch and Flash-to-Pass Headlight Low/High Beam Select Switch When the headlights are turned on, pushing the lever assembly toward the instrument panel will switch from low beams to high beams. Pulling back to the neutral position returns to low beam headlights. Flash-to-Pass (Optical Horn) You can signal another vehicle with your headlights by lightly pulling the mul- tifunction lever toward you. This will cause the head- lights to turn on at high beam and remain on until the lever is released.

WARNING!

Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.

Headlights On When Wipers Are On — If Equipped Headlights on when windshield wipers are on may be found on vehicles equipped with automatic headlight system. Refer to the Electronic Vehicle Information Cen- ter (EVIC) in Section 4 under “PERSONAL SETTINGS (CUSTOMER PROGRAMMABLE FEATURES)” for more information.

the small

the column, pull

TILT STEERING COLUMN — IF EQUIPPED To tilt lever downward (located on the steering column and below the steering wheel) to the open position. You may then position the steering wheel up or down, as desired. Pull the small lever upward to the closed position to lock the steering wheel firmly in place.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169

WARNING!

Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.

Tilt Steering Column Control

170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

REAR PARK ASSIST SYSTEM — IF EQUIPPED The Rear Park Assist System provides visual and audible indications of the distance between the rear fascia and the detected obstacle when backing up. When backing up the driver should also use the inside rearview and outside mirrors. The Rear Park Assist System will remember the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the RUN/ON position. The Rear Park Assist System can be active only when the transaxle gear selector lever is in REVERSE. When in REVERSE, the system scans for objects behind the vehicle using four sensors located in the rear bumper.

NOTE: The system will be active until the vehicle speed is increased to approximately 11 mph (18 km/h) or above. The system will be active again if the vehicle speed is decreased to speeds less than approximately 10
mph (16 km/h). Rear Park Assist Sensors The four Rear Park Assist Sensors, located in the rear fascia, monitor the area behind the vehicle that is within the sensors’ field of view. The monitored area seems oval in shape. The sensors can detect obstacles from approxi- mately 11.8 in (30 cm) up to 78.7 in (200 cm) from the rear fascia in the horizontal direction, depending on the location and orientation of the obstacle and the type of obstacle.

Rear Park Assist Warning Display The Rear Park Assist Warning Display, located in the headliner near the liftgate glass, provides both visual and audible warnings to indicate the distance between the rear fascia and the detected obstacle.

Rear Park Assist LED Lights

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171

When the ignition switch is turned to the RUN/ON position, the warning display will turn on all of its LEDs for about one second. Each side of the warning display has six yellow and two red LED lights, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle. The vehicle is close to the obstacle when the red LED is illuminated. The driver can view the LEDs either through the rear- view mirror or by looking directly at the display above the rear window. The system dimly illuminates the two outer most yellow LEDs when it is on and detects no obstacles. The follow- ing chart shows the warning display operation when the system is detecting an obstacle.

172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

PARK ASSIST WARNING DISPLAY DISTANCES

DISPLAY LED

OBSTACLE DISTANCE FROM:

1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED

8th LED

REAR CORNERS

31.5 in (80 cm) 25.5 in (65 cm) 20 in (50 cm) 16 in (40 cm)

REAR CENTER 78.7 in (200 cm) 51.1 in (130 cm) 45.2 in (115 cm) 39.3 in (100 cm) 33.5 in (85 cm) 27.6 in (70 cm) 19.7 in (50 cm)

6 in (15 cm)

11.81 in (30 cm)

REAR CENTER

AUDIBLE SIGNAL

Yellow Yellow Yellow Yellow Yellow Yellow Red

Red

Yes, Half Second

None None None None None

at 12 in (30 cm)

Intermittent at 8 in (20 cm)

Continuous

NOTE: The Rear Park Assist System will MUTE the radio, if on, when the audible warning is activated.

WARNING!

Drivers must be careful when backing up even when using the Rear Park Assist System. Always check care- fully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death. Before using the Rear Park Assist System, it is strongly recommended that the ball mount and hitch ball assembly be disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns the red LEDs on. Also, the sensors could detect the ball mount and hitch ball assem- bly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173

CAUTION!

† To avoid vehicle damage the Rear Park Assist System should only be used as a parking aid and is unable to recognize every obstacle, including small objects. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity to the rear of the vehicle. † To avoid vehicle damage the vehicle must be driven slowly when using the Rear Park Assist System to be able to stop in time when an obstacle is detected. It is recommended that the driver look over his/her shoulder when using the Rear Park Assist System.

174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE: † Ensure that the rear bumper is free of dirt and debris † Jackhammers, large trucks, and other vibrations could

to keep the system operating properly.

affect the performance of the system.

Enabling and Disassembling The Rear Park Assist System There are times when you may want to disable the Rear Park Assist System, such as when towing a trailer. NOTE: The manufacturer suggests disabling the Rear Park Assist System when towing a trailer. Refer to the following procedures. Vehicles Equipped With the Electronic Vehicle Information Center (EVIC) You can turn the Rear Park Assist System on or off through the EVIC. For details, refer to “Personal Settings

(Customer Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. Vehicles Equipped With the Compass Mini-Trip Computer (CMTC) You can turn the Rear Park Assist System ON or OFF through the CMTC by pressing the left reset button in the instrument cluster. Turn the ignition switch to the ON position, then press and hold the rest button for approxi- mately two seconds. Service The Rear Park Assist System If the Rear Park Assist System malfunctions, the instru- ment cluster will actuate a single chime, once per ignition cycle, and it will display the (SERVICE PARK ASSIST SYSTEM( message. Refer to “Compass Mini Trip Com- puter (CMTC) or “Electronic Vehicle Information Center (EVIC)” — as equipped, in Section 4 of this manual.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175

ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjustable pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat positions. The switch is located on the left side of the steering column.

If (SERVICE PARK ASSIST SYSTEM( appears in the Electronic Vehicle Information Center (EVIC), after mak- ing sure the rear bumper is clean, please see your authorized dealer.

Should this wrench symbol display with the letter P next to it, your Park Sense System needs servicing. Contact your authorized dealer.

Cleaning The Rear Park Assist System Clean the Rear Park Assist Sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors, otherwise, you could damage the sensors.

Adjustable Pedal Switch

176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Press the button forward to move the pedals forward (toward the front of the vehicle). Press the button rearward to move the pedals rearward (toward the driver). † The pedals can be adjusted with the ignition OFF. † The pedals can be adjusted while driving. † The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control Sys- tem is ON. The following messages will be displayed on vehicles equipped with the Electronic Vehicle In- formation System (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjust- able Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”).

CAUTION!

Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path.

ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h).

Electronic Speed Control Switches

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177

Activating Electronic Speed Control Push the ON/OFF button (located in the end of the lever) once and the CRUISE indicator light (located in the message window of the odometer) will illuminate show- ing the electronic speed control system is on. To turn the system OFF, push the ON/OFF button again and the system and indicator will turn off.

WARNING!

Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently SET the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you aren’t using it.

178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Setting Electronic Speed Control at a Desired Speed When the vehicle has reached the desired speed, press the SET lever downward and then release. Lift your foot off the accelerator and the vehicle will operate at the selected speed. Deactivating Electronic Speed Control A soft tap on the brake pedal or pulling the lever CANCEL toward you, will deactivate the speed control without erasing the set speed memory. Pushing the ON/OFF button to the OFF position or turning OFF the ignition erases the set speed memory. Resuming Speed To resume a previously set speed, raise the lever RESUME/ACCEL upwards and release. Resume can be used at any speed above 25 mph (40 km/h).

Varying The Speed Setting When the speed control is SET, speed can be increased by raising and holding the RESUME/ACCEL lever up- wards. When released, a new set speed will be estab- lished. Raising the lever RESUME/ACCEL upwards once will result in a 1 mph (1 km/h) speed increase. Each time the lever is tapped upwards, speed increases so that tapping the lever three times will increase speed by 3 mph (5
km/h), etc. To decrease speed while speed control is SET, press the lever SET/DECEL downward and hold. Release the lever when the desired speed is reached, and the new speed will be SET. Tapping the lever SET/DECEL downward once will result in a 1 mph (1 km/h) speed decrease. Each time the lever is tapped downward, speed decreases.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179

On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.

WARNING!

Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.

NOTE: The Electronic Speed Control system has been designed to shut down if multiple speed control switch functions are operated simultaneously in order to ensure proper operation. If this occurs, the system can be reactivated by pushing the speed control switch ON/ OFF button and resetting the desired vehicle SET speed. Accelerating To Pass Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: The speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. Your vehicle may experience a downshift (automatic transmissions only) while climbing uphill or descending downhill. This downshift is necessary to maintain vehicle set speed.

180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

OVERHEAD CONSOLES

Front Overhead Console — If Equipped Two versions of the overhead console are available. The base front overhead console models feature fixed incan- descent courtesy/reading lights, flip-down sunglass stor- age and conversation mirror. Premium front overhead console models feature an LED focused light that illuminates the instrument panel cup holders, Infrared Automatic Temperature Control Sensor (ATC equipped only), two swiveling LED lights, flip- down sunglass storage, conversation mirror, optional power sliding door switches and an optional power liftgate switch.

Front Premium Overhead Console Features

1 - Cupholder LED 2 - ATC Sensor 3 - Interior Lights

4 - Storage/Mirror 5 - Switch Bank

Courtesy/Interior Lighting At the forward end of the console are two courtesy lights (standard dome light has two buttons). The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry, the lights will also turn on when the unlock button on the transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle. Press a second time to turn the each light off. You may adjust the direction of these lights by pressing the outside ring which is identified with four directional arrows. The area around the instrument panel cupholders is also illuminated from a light in the overhead console. This light is turned on when the headlight switch is on and will adjust in brightness when the dimmer control is rotated up or down.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181

Sunglass Storage At the rear of the front overhead console, a compartment is provided for the storage of two pairs of sunglasses. Press the door latch to open the compartment. The door will slowly rotate to an open position. NOTE: The front overhead console used with factory sunroof incorporates a sunroof switch. Rear Overhead Consoles — If Equipped The rear overhead storage system is available in two versions: with or without sunroof. An additional LED at the front of the rear console shines down on the second row footwell area while in courtesy mode, for added convenience.

182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Overhead Compartment Features

1 — DVD 1
2 — Rear HVAC 3 — Interior Lights 4 — Storage 1 If equipped, otherwise storage.

5 — Storage 6 — DVD 1
7 — Interior Lights 8 — Halo Lighting

Rear Courtesy/Reading Lights — If Equipped The overhead console had two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry, the lights will also turn on when the unlock button on the transmitter is pressed. The courtesy lights also function as reading lights. Press in on each lens to turn these lights on while inside the vehicle. Press a second time to turn the each light off. You may adjust the direction of these lights by pressing the outside ring which is identified with four directional arrows. Rear Console Halo Lighting — If Equipped The rear overhead console features recessed halo lighting around the perimeter of the console base. This feature provides additional lighting options while traveling and is controlled by the headlight switch. Refer to “Halo

Lighting - If Equipped” under “Lighting” in “Under- standing The Features Of Your Vehicle” in Section 3.

GARAGE DOOR OPENER — IF EQUIPPED HomeLinkt replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLinkt unit operates off your vehicle’s battery. The HomeLinkt buttons that are located in the headliner or sun visor designate the three different HomeLinkt channels.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183

HomeLinkt Buttons

NOTE: HomeLinkt is disabled when the Vehicle Secu- rity Alarm is active.

184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

WARNING!

Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety stan- dards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1–800–355–3515
at www.HomeLink.com for safety information or assistance.

Internet

the

on

or,

Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause seri- ous injury or death.

PROGRAMMING HOMELINKT

Before You Begin If you have not trained any of the HomeLinkt buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for 20
seconds until the red indicator flashes. It is recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLinkt for more efficient training and accurate transmission of the radio-frequency signal.

Your vehicle should be parked outside of the garage when programming. Begin Programming 1. Turn the ignition switch to the ON/RUN position. 2. Hold the battery side of the hand-held transmitter away from the HomeLinkt button you wish to program. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLinkt button you wish to program while keeping the indicator light in view. 3. Simultaneously press and hold both the chosen HomeLinkt button and the hand-held transmitter button until the HomeLinkt indicator changes from a slow to a rapidly blinking light, then release both the HomeLinkt and hand-held transmitter buttons.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185

Watch for the HomeLinkt indicator to change flash rates. When it changes, it is programmed. It may take up to 30
seconds, or longer in rare cases. The garage door may open and close while you train. NOTE: Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. NOTE: After training a HomeLinkt channel, if the garage door does not operate with HomeLinkt and the garage door opener was manufactured after 1995, the garage door opener may have a rolling code. If so, proceed to Step 5 “Programming A Rolling Code Sys- tem.” 4. Press and hold the just-trained HomeLinkt button and observe the indicator light.

186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

If the indicator light stays on constantly, programming is complete and the garage door (or device) should activate when the HomeLinkt button is pressed. If the indicator light blinks rapidly for two seconds, and then turns to a constant light, proceed to Step 5 “Pro- gramming A Rolling Code System.” 5. Programming A Rolling Code System At the garage door opener motor (in the garage), locate the “Learn” or “Training” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door).

GARAGE DOOR OPENER TRAIN BUTTON

1 — Door Opener

2 — Training Button

6. Firmly press and release the “Learn” or “Training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmed HomeLinkt button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. To program the remaining two HomeLinkt buttons, repeat each step for each remaining button. DO NOT erase the channels.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187

Using HomeLinkt To operate, simply press and release the programmed HomeLinkt button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc. The hand-held transmitter of the device may also be used at any time. Reprogramming a Single Homelinkt Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLinkt button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button, proceed with Program- ming Homelinkt Step 2 and follow all remaining steps.

188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

GATE OPERATOR/CANADIAN PROGRAMMING Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission – which may not be long enough for HomeLinkt to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor. If you are having difficulties programming a garage door opener or a gate operator, replace “Programming HomeLinkt” Step 3, with the following: 3. Continue to press and hold the HomeLinkt button while you press and release - every two seconds (“cycle”) your hand-held transmitter until HomeLinkt

has successfully accepted the frequency signal. The indicator light will flash slowly and then rapidly when fully trained. If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Programming HomeLinkt,” earlier in this section. SECURITY It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20
seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The HomeLinkt Universal Transceiver is disabled when the Vehicle Security Alarm is active.

TROUBLESHOOTING TIPS If you are having trouble programming HomeLinkt, here are some of the most common solutions: † Replace the battery in the original transmitter. † Press the “Learn” button on the Garage Door Opener † Did you unplug the device for training, and remember

to complete the training for a Rolling Code.

to plug it back in?

If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. GENERAL INFORMATION This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189

2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the device. The term IC before the certification/registration number only signifies that Industry Canada technical specifica- tions were met.

POWER SUNROOF — IF EQUIPPED The power sunroof control switch is located in the front overhead console. The sunroof panel tilts upward at the rear for ventilation or slides rearward under the roof.

190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Power Sunroof Operation

Opening the Sunroof Manually Press the switch rearward and hold, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. During this opera- tion, any release of the sunroof switch will stop the sunroof.

WARNING!

In an accident, there is greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too.

Closing the Sunroof Manually To close the sunroof from an open or vent position, press and hold the switch forward. The sunroof will close fully and stop automatically. Release the switch to stop sun- roof travel at any point. Sunroof Sunshade Operation The sunroof sunshade can be opened manually. How- ever, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open.

WARNING!

Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.

Express-Open Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called Express-Open. During Express-Open operation, any movement of the sunroof switch will stop the sunroof.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191

Express-Vent Press and release the 9V9 button, and the sunroof will automatically open to the vent position. This is called Express-Vent. Express-Close Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully, then stop automatically. This is called Express-Close. During Express-Close operation, any movement of the sunroof switch will stop the sunroof.

WARNING!

Do not allow small children to operate the sunroof. Never allow fingers or other body parts, or any object to project through the sunroof opening. Injury may result.

192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Ignition OFF Operation The power sunroof switch will remain active for 10
minutes after the ignition switch is turned OFF. Opening either front door will cancel this feature. Auto-Express with Anti–Pinch Protection During express closing, anytime an obstacle that restricts glass movement is detected, the motor will stop and reverse travel to avoid pinching the object. Auto Express will stop and reverse travel up to three times in succession. After the third time, Auto Express will enter a manual operation mode. This allows the operator to manually control the power switch in order to close or open the sunroof in case of a malfunction.

Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel.

ELECTRICAL POWER OUTLETS — IF EQUIPPED Two 12 volt power outlets are located in the center lower instrument panel next to the open storage bin. The upper outlet is controlled by the ignition switch and the lower outlet is connected directly to the battery. The upper outlet will also operate a conventional cigar lighter unit (if equipped with an optional Smoker’s Package).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193

The outlets include tethered caps labeled with a key or battery symbol indicating the power source. The lower instrument panel outlet is powered directly from the battery, items plugged into this outlet may discharge the battery and/or prevent engine starting. The lower outlet is protected by an automatic reset circuit breaker. The automatic circuit breaker restores power when the overload is removed. The circuit breaker also supplies power to the outlet in the removable floor console, when in the front position. Refer to section 3
“Removable Floor Console” in this manual. A third outlet is located on the driver’s side, just to the rear of the sliding door and is also controlled by the ignition switch. The lower and rear outlets will not accommodate a conventional cigar lighter unit. If desired, all of the power outlets can be NOTE: converted by your authorized dealer to provide power with the ignition switch in the OFF position.

194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

POWER INVERTER — IF EQUIPPED A 110 volt, 150 watt inverter outlet (if equipped) converts DC current to AC current and is located on the left rear trim panel immediately behind the second row left passenger seat. This outlet can be used to power small appliances and electronics.

The Power Inverter switch is located near the center of the instrument panel below the two 12 volt power outlets. Press the switch to turn the power on for the outlet, press the switch a second time to turn the power off.

110 Volt Power Inverter

Inverter Outlet Power Switch

NOTE: † When the Inverter Switch is pressed, there will be a delay of approximately one second before the inverter status indicator turns ON. The status indicator of the AC power inverter indicates whether the inverter is producing AC power. † Due to built-in overload protection the inverter will

shut down if the power rating is exceeded.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195

WARNING!

To Avoid Serious Injury or Death: † Do not use a Three–Prong Adaptor. † Do not insert any objects into the receptacles. † Do not touch with wet hands. † Close the lid when not in use. † If this outlet is mishandled it may cause an electric

shock and failure.

196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

ELECTRICAL OUTLET USE WITH ENGINE OFF

CAUTION!

† Many accessories that can be plugged in draw power from the

vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.

† Accessories that draw higher power (i.e., coolers, vacuum

cleaners, lights, etc.), will degrade the battery even more quickly. Only use these intermittently and with greater cau- tion.

† After the use of high power draw accessories, or long periods

of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the alternator to recharge the vehicle’s battery.

† Power outlets are designed for accessory plugs only. Do not

hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage.

SUN SCREENS— IF EQUIPPED Sun Screens are available for second and third row seating windows. The screens store in the sill trim panels and the tops of the windows are equipped with hooks that the Sun Screen attaches to when pulled out.

Sun Screen Retracted

Gently pull up on the tab to raise the sun screen. Continue pulling the sun screen until the tab is near the top of the window.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197

Sun Screen Attaching To Retainer Clips

Once the screen is completely to the top of the window, extend the top bar of the sun screen over the two hooks attached to the top of the window.

Sun Screen Extended

To lower the sun screen, gently lift the tab upwards to disengage the hooks and feed the screen back into the base sill.

198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CUP HOLDERS AND CONVENIENCE TRAY DRAWER There are nine cup holders in the interior. Two cup holders in the center front instrument panel, four in the floor consoles and three more are located in the third row quarter trim panel. All liners are removable for cleaning. Pull the flexible liner from the cup holder drawer or tray; starting at one edge to ease removal. Refer to “Cleaning The Instrument Panel Cup Holders” in Section 7. Instrument Panel Cup Holders The instrument panel cup holders are located in a pull out drawer just above the lower storage bin.

Front Cup Holders

Pull the drawer out firmly until it stops, and place the container to be held in either one of the cup holder wells. The cup holders are designed to accommodate a wide variety of container types and sizes. Press down on the container to engage the cup holder retention fingers.

Interior Bottle Holders There are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel. Each holder accommo- dates up to 20 oz. (.6 L) size plastic bottles. Two outboard mesh pockets on intermediate seating. The mesh pockets are flexible enough to hold juice boxes, toys, games or MP3 players, etc.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199

Smokers Package Kit — If Equipped With the optional authorized dealer-installed Smokers Package Kit, a removable ash receiver is inserted into one of the two cup holders in the center front instrument panel. To install the ash receiver, align the receiver so the thumb grip on the lid is facing rearward. Press the ash receiver into either of the cup wells to secure. Pull upward on the ash receiver to remove for cleaning and/or storage. The left rear trim panel cup holder is designed to accommodate a second ash receiver if desired.

200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

easily pass through the first row to the second.

CONSOLE FEATURES There are two consoles available: Basic and Premium. Basic Console Basic Console features consist of the following: † The basic console profile allows vehicle occupants to † Four cup holders can accept extra large size beverage cups or 20 oz (.6 L) plastic bottles. The cup holders are dishwasher safe for cleaning. To remove, pull the flexible liner from the cup holder drawer or tray; starting at one edge. Refer to “Cleaning The Instru- ment Panel Cup Holders” in Section 7 for more detailed information. † A Top Storage Tray. † The cup holder/tray top is removable to access a large

storage bin.

† The Basic Console is removable from the vehicle for additional floor space by removing the cap at the console base.

Basic Console Features

1 - Console Anchor 2 - Top Tray

3 - Front Cup holders 4 - Rear Cup holders

clear the rear load floor hook.

To Remove The Basic Floor Console † Remove the front anchor cup plug and clip. † Slide the console base forward while lifting slightly to † Remove the console. To Reinstall The Basic Floor Console † Position the console at a slight angle (front slightly † Slide the console rearward into the floor bracket/hook. † Align the console until the front anchor cup plug hole † Reinstall the clip first and then while pushing down- ward on the console with slight pressure, reinstall the cover plug. † Pull up on the console to be sure it is firmly latched.

is centered on the winch hole.

higher than the rear.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201

WARNING!

In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.

Premium Console – If Equipped The three-compartment console with sliding storage bin, sliding upper tray with storage and large console storage bin offers multiple configurations. † Four cup holders can accept large cups or mugs with handles or 20 oz (.6 L) plastic bottles. The cup holders are dishwasher safe for cleaning. To remove, pull the flexible liner from the cup holder drawer or tray; starting at one edge. Refer to “Cleaning The Instru- ment Panel Cup Holders” in Section 7 for more detailed information.

202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CD’s or other items

† Top Tray Storage † Upper Storage Bin can hold nine regular or 18 thin † Large Console Center Storage will store headphones for the available rear DVD entertainment system or other items † 12–Volt DC Power Outlet provides continuous power inside the console for cell phones or other electronics. † Rear Occupant Accessible † Multiple Adjustments † Removable from vehicle for additional floor space.

Premium Console Features

3 - Console Release

1 - Top Release 2 - Center Release The top and center console sections slide forward and rearward to provide added user comfort. Four cup hold- ers, each of which can accommodate large sized beverage containers. A one-piece cup holder insert for both cavities

can easily be removed for cleaning. The cup holders will also accommodate large size cups and 20 oz (.6 L) bottles. Position 1 shows the console closed with four cup holders and a convenient storage tray.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203

Position 2 shows the raised storage tray revealing a large storage area below.

Console Position 1

Console Position 2

204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Dual Storage Bins Position 3 shows the top portion of the console in a rearward position. This is accomplished by lifting the upper most latch at the front of the console. This provides easy access to the storage area below and provides two of the four cup holders for the second row passengers.

Position 4 shows the complete console in its rearmost position. Again, lifting second latch handle at the front of the console, allows complete access to a lower storage bin and provides additional cup holders for rear passengers.

Console Position 3

Console Position 4

console

To Remove The Premium Floor Console † Pull up on the bottom release handle in the front of the † Lift the rear of the console up several inches † Pull rearward to disengage from floor and remove

console

To reinstall the console: † Position the console at a slight angle (rear slightly † Slide the console forward into the floor bracket

higher than the front

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205

on the floor bracket

† Rotate the rear of the console down until it is resting † Push down on the rear of the console until it is seated † Pull up on the console to be sure it is firmly latched

in the rear floor bracket

WARNING!

In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.

206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

STORAGE

Glove Compartments

There are both upper and lower glove compartments. Upper Glove Compartment To open the upper compartment (1), press inward on the release button (2). The door will spring open about one in (2.54 cm). Manually lift the front edge of the door upward, until fully opened, and the detent is engaged.

Glove Compartment Features

3 - Lower Latch/Lock 4 - Lower Compartment

1 - Upper Compartment 2 - Upper Latch To close the compartment door, push firmly downward on the door’s surface to release the detent and latch the door closed.

Lower Glove Compartment To open the lower compartment (4) pull out on the release handle (3). The lower compartment handle is also equipped with a lock. Door Trim Panel Storage

Front Door Storage Both interior front door panels have multiple pockets for storage.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207

Front Door Storage

1 - Storage Pocket 2 - Rear Map Pocket

3 - Bottle Holder 4 - Front Map Pocket

208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Sliding Side Door Bottle Holder Both sliding doors have a bottle holder molded right into the trim.

Driver Seatback Storage — If Equipped The Driver’s Seat Back has a Primary Storage Pocket on all models and an optional Secondary Mesh Pocket.

Sliding Door Bottle Holder

Driver’s Seatback Storage

1 - Standard Pocket 2 - Mesh Pocket 3 - Bag Holder

4 - Bottle Holder 5 - Side Mesh Pocket

Second Row Floor Storage Bins — If Equipped The Second Row Seat Storage Bins are located on the floor in front of the second row seats. The area below the floor covers can be used for storage when the second row seat is in the upright position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209

Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the 9unlocked9
position to allow greater access to the storage bin.

CAUTION!

The storage bin cover must lay flat and be locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.

Storage Bin Cover Lock Release

210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!

covers open.

In an accident, serious injury could result if the seat storage bin covers are not properly latched. † DO NOT drive the vehicle with the storage bin † Keep the storage bin covers closed and latched † DO NOT use a storage bin latch as a tie down.

while the vehicle is in motion.

Removing The Floor Console With Stow ’n Go Seating — If Equipped The removable floor console has two power outlets, storage tray, light, removable cell phone holder, tissue holder, pen holder and a map holder. It can be removed from the vehicle by pulling the release handle inside the floor console.

To remove the console use the following procedure: 1. Open the console lid and remove the storage tray. 2. Pull up on the release handle located inside the floor console, and slide the console rearward to disengage from the floor. 3. Remove the floor console. To reinstall the console use the following procedure: 1. Open the console lid and remove the storage tray. 2. Pull up on the release handle and slide the console forward to engage the front of the console into the floor tray. 3. Pivot the floor console down until it is seated on the floor tray and release the handle.

4. Pull up on the console to be sure it is firmly attached.

WARNING!

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211

In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched.

Removable Floor Console Features

1 - Removal Latch 2 - Lower Latch 3 - Upper Latch

4 - Front Cupholders 5 - Top Tray 6 - Rear Cupholders

212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Rear Compartment Storage Your vehicle is equipped with open storage areas located in each rear trim panel.

Third Row Rear Seat and Rear Compartment Features 1 — Tie Down 2 — Rear Switches 3 — Tire Jack/Handle 4 — Cubby/Speaker

5 — Liftgate Close 6 — Bag Holders 7 — LATCH Anchor 8 — Flash Light

Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle. Cargo Area Storage The seats in your vehicle are in-line which enables you to stow long objects, such as lumber or skis, on the floor without moving the seats. NOTE: With all rear seat backs folded, a 4 ft x 8 ft (1.2 m x 2.4 m) sheet of building material may be stored on top of the folded seats with the liftgate closed. The front seats must be moved slightly forward of the rearmost position. If the rear seats are removed no front seat adjustment is needed and more than one 4 ft x 8 ft (1.2 m x 2.4 m) sheet of building material may be stored.

The liftgate sill plate has a raised line with the statement “Load To This Line”. This line indicates how far rearward cargo can be placed without interfering with liftgate closing.

Rear Cargo Area Loading Limit

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213

ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity. To move the crossbars, loosen the thumb screws located at the upper edge of each crossbar approximately six turns, then move the crossbar to the desired position, keeping the crossbars parallel to the rack frame. Once the crossbar is in place, retighten the thumb screws to lock the crossbar into position.

214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Attempt to move the crossbar again to ensure that it has properly locked into position. NOTE: To help control wind noise when installing the crossbars make sure the arrows marked on the underside of the crossbars are facing the front of the vehicle. When the crossbars are not in use, the front crossbar should be fastened just forward of the middle support and the rear crossbar should be fastened at the rearmost position of the side rails. This will help reduce the amount of wind noise when the crossbars are not in use. The tie down holes on the crossbar ends should always be used to tie down the load. Check the straps frequently to be sure that the load remains securely attached.

CAUTION!

† Crossbars should remain equally spaced or paral- lel at any luggage rack position for proper func- tion. Noncompliance could result in damage to the luggage rack, cargo and/or vehicle. † To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150
lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215

WARNING!

Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.

CAUTION!

† Long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle. † Travel at reduced speeds and turn corners care- fully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift to a load. This is especially true on large flat loads and may result in damage to the cargo or your vehicle.

216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

UMBRELLA HOLDER An umbrella holder has been conveniently molded into the left front door entry scuff molding.

LOAD-LEVELING SYSTEM — IF EQUIPPED The automatic load-leveling system will provide a level riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6 km) of driving for the leveling to complete depending on road surface conditions. If the leveled vehicle is not moved for approximately 15
hours, the leveling system will bleed itself down. The vehicle must be driven to reset the system.

Umbrella Holder

WARNING!

Do not install the load-leveling system on vehicles that are not equipped with Anti-Lock Brakes. Ve- hicles without Anti-Lock Brakes (ABS) have a height- sensing proportioning valve. Installing a leveling system will render this system ineffective, inappro- priately reducing rear brake pressure, resulting in increased stopping distances. You could have a seri- ous accident.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217

UNDERSTANDING YOUR INSTRUMENT PANEL

CONTENTS

m Instrument Panels And Controls . . . . . . . . . . . . 223
m Base Instrument Cluster . . . . . . . . . . . . . . . . . . 224
m Premium Instrument Cluster . . . . . . . . . . . . . . . 225
m Instrument Cluster Descriptions . . . . . . . . . . . . 226
m Compass Mini-Trip Computer (CMTC) —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
N Compass Mini-Trip Computer (CMTC)

Odometer Displays . . . . . . . . . . . . . . . . . . . . 239

N Compass Mini-Trip Computer (CMTC)

Reset Buttons . . . . . . . . . . . . . . . . . . . . . . . . 240

N Compass/Temperature Display . . . . . . . . . . . 241

m Electronic Vehicle Information Center (EVIC) —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
N EVIC Displays . . . . . . . . . . . . . . . . . . . . . . . 244
N Trip Functions . . . . . . . . . . . . . . . . . . . . . . . 246
N Compass Display . . . . . . . . . . . . . . . . . . . . . 247
N Personal Settings (Customer Programmable

Features)

. . . . . . . . . . . . . . . . . . . . . . . . . . . 249
m Radio General Information . . . . . . . . . . . . . . . . 252
N Radio Broadcast Signals . . . . . . . . . . . . . . . . . 252

220 UNDERSTANDING YOUR INSTRUMENT PANEL

m Sales Code REQ — AM/FM Stereo Radio And

6–Disc CD/DVD Changer (MP3/WMA AUX Jack) . . . . . . . . . . . . . . . . . . 254
N Operating Instructions - Radio Mode . . . . . . . 254
N Operation Instructions - (Disc Mode For CD

And MP3/WMA Audio Play, DVD-Video) . . . . 262
N Notes On Playing MP3/WMA Files . . . . . . . . 264
N List Button

(Disc Mode For MP3/WMA Play) . . . . . . . . . . 267

N Info Button

(Disc Mode For MP3/WMA Play) . . . . . . . . . . 267

m Sales Code RES — AM/FM Stereo Radio

With CD Player (MP3 AUX Jack) . . . . . . . . . . . . 269
N Operating Instructions - Radio Mode . . . . . . . 270

N Operation Instructions - CD Mode For CD

And MP3 Audio Play . . . . . . . . . . . . . . . . . . 275
N Notes On Playing MP3 Files . . . . . . . . . . . . . 277
N List Button (CD Mode For MP3 Play) . . . . . . . 280
N Info Button (CD Mode For MP3 Play) . . . . . . . 280

m Sales Code REN — Multimedia System —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
N Operating Instructions — Satellite Radio

(If Equipped)

. . . . . . . . . . . . . . . . . . . . . . . . 282

N Operating Instructions — Voice Recognition

System (VR) (If Equipped) . . . . . . . . . . . . . . . 283

N Operating Instructions — Hands-Free

Communication (UConnectt) (If Equipped) . . . 283
N Clock Setting Procedure . . . . . . . . . . . . . . . . . 283

m Sales Code RER — Multimedia System —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
N Operating Instructions — Satellite Radio . . . . . 286
N Operating Instructions — Hands-Free

Communication (UConnectt) (If Equipped) . . . 286
N Clock Setting Procedure . . . . . . . . . . . . . . . . . 286

m Satellite Radio — If Equipped

(REN/REQ/RER/RES/REU Radios Only) . . . . . 288
N System Activation . . . . . . . . . . . . . . . . . . . . . 289
N Electronic Serial Number/Sirius Identification

Number (ESN/SID) . . . . . . . . . . . . . . . . . . . . 289
N Selecting Satellite Mode . . . . . . . . . . . . . . . . . 290
N Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . 290
N Reception Quality . . . . . . . . . . . . . . . . . . . . . 290

UNDERSTANDING YOUR INSTRUMENT PANEL 221

N Operating Instructions - Satellite Mode . . . . . . 290
N Operating Instructions - Hands-Free Phone

(If Equipped)

. . . . . . . . . . . . . . . . . . . . . . . . 293

N Operating Instructions - Video Entertainment

System (VESt) (If Equipped)

. . . . . . . . . . . . . 293

m Universal Consumer Interface (UCI) —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
N Connecting The iPodt Device . . . . . . . . . . . . 294
N Controlling The iPodt Using Radio Buttons . . . 294
N Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 295
N List Or Browse Mode . . . . . . . . . . . . . . . . . . 296
m Sirius Backseat TV&Trade; — If Equipped . . . . . 298
m Video Entertainment System (VESt) —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 299

222 UNDERSTANDING YOUR INSTRUMENT PANEL

m Radio Operation And Cellular Phones . . . . . . . . 300
m Remote Sound System Controls — If Equipped . . 300
N Radio Operation . . . . . . . . . . . . . . . . . . . . . . 301
N CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . 301
m CD/DVD Maintenance . . . . . . . . . . . . . . . . . . . 301
m Climate Controls . . . . . . . . . . . . . . . . . . . . . . . 302

N Manual Heating, Ventilation And Air

Conditioning (HVAC) System . . . . . . . . . . . . . 302

N Rear Manual Climate Control Zone —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 308

N Automatic Temperature Control (ATC) —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 311

N Summer Operation . . . . . . . . . . . . . . . . . . . . 319
N Winter Operation . . . . . . . . . . . . . . . . . . . . . 319
N Vacation/Storage . . . . . . . . . . . . . . . . . . . . . 320
N Window Fogging . . . . . . . . . . . . . . . . . . . . . 320
N Outside Air Intake . . . . . . . . . . . . . . . . . . . . 320
N Operating Tips . . . . . . . . . . . . . . . . . . . . . . . 321
N A/C Air Filter — If Equipped . . . . . . . . . . . . 321

m Electric Rear Window Defroster —

If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 321

INSTRUMENT PANELS AND CONTROLS

UNDERSTANDING YOUR INSTRUMENT PANEL 223

1 - Air Vents 2 - Instrument Cluster 3 - Gear Selector Lever 4 - Radio 5 - Analog Clock

6 - Upper Glove Compartment 7 - Lower Glove Compartment 8 - Climate Controls 9 - Storage or DVD— If Equipped 10 - Cup Holders

11 - Storage Bin 12 - Power Supply 12V 13 - Hazard Switch 14 - Ignition Switch 15 - Dimmer Switch

16 - Head Light Switch 17 - Power Inverter Switch

224 UNDERSTANDING YOUR INSTRUMENT PANEL

BASE INSTRUMENT CLUSTER

PREMIUM INSTRUMENT CLUSTER

UNDERSTANDING YOUR INSTRUMENT PANEL 225

226 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTER DESCRIPTIONS

1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. Low Fuel Light

When the fuel level reaches approximately 2.0 gals (7.8 L) this light will turn on and remain on until fuel is added.

3. Electronic Throttle Control (ETC.) Light

This light informs you of a problem with the Electronic Throttle Control system. If a prob- lem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the gear selector is placed in the PARK position. The light should turn off. If the light remains lit with the engine running your vehicle will usually be drivable, however, see your authorized dealer for service as soon as possible. If the

light is flashing when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. The light will come ON when the ignition is first turned on and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. 4. Voltage Light

This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained.

5. Tire Pressure Monitoring Telltale Lamp — If Equipped

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to

UNDERSTANDING YOUR INSTRUMENT PANEL 227

overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. NOTE: Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsi- bility to maintain correct tire pressure, even if underin- flation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure

228 UNDERSTANDING YOUR INSTRUMENT PANEL

as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. NOTE: Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.

CAUTION!

The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use aftermarket tire sealants or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.

For additional information on TPMS, refer to Section 5 — Starting and Operating, “Tire Pressure Monitoring Sys- tem” of this manual.

For additional information on Tire Pressures, refer to Section 5 — Starting and Operating, “Tire Inflation Pressures” of this manual. 6. Oil Pressure Warning Light

This light shows low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. 7. Engine Temperature Warning Light

This light warns of an overheated engine condi- tion. If the engine is critically hot, a continuous

UNDERSTANDING YOUR INSTRUMENT PANEL 229

chime will sound for four minutes. After the chime turns off, the engine will still be critically hot until the light turns off. 8. Speedometer Indicates vehicle speed. 9. Turn Signal Indicators

The arrow will flash with the exterior turn signal when the turn signal lever is operated.

If the vehicle electronics sense that the vehicle has traveled about one mile with the turn signals on, a continuous chime will sound to alert you to turn the signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. 10. Electronic Stability Program (ESP) Indicator Light The malfunction lamp for the ESP is combined with BAS. The yellow “ESP/BAS Warning Lamp” comes on when the ignition switch is

230 UNDERSTANDING YOUR INSTRUMENT PANEL

turned to the “ON” position. They should go out with the engine running. If the “ESP/BAS Warning Lamp” comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible. 11. Brake System Warning Light

This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system (if equipped). The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. Failure of either half of the dual brake system is

indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected. NOTE: The light may flash momentarily during sharp cornering maneuvers which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces- sary.

WARNING!

Driving a vehicle with the brake light on is danger- ous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately.

Vehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. The operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approxi- mately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application.

UNDERSTANDING YOUR INSTRUMENT PANEL 231

12. Vehicle Security Light — If Equipped

This light will flash at a fast rate for approxi- mately 16 seconds when the vehicle security alarm is arming and then will flash slowly until the system is disarmed. 13. Anti-Lock Brake System Light

This light monitors the Anti-Lock Brake Sys- tem. The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds.

If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock

232 UNDERSTANDING YOUR INSTRUMENT PANEL

brakes. If the ABS light does not turn on when the Ignition switch is turned to the ON position, have the light inspected by an authorized dealer. 14. Electronic Stability Program (ESP) Indicator Light/Traction Control System (TCS) Indicator Light

If this indicator light flashes during accelera- tion, apply as little throttle as possible. While driving, ease up on the accelerator. Adapt your speed and driving to the prevailing road con-

ditions, and do not switch off the ESP, or TCS. 15. Tachometer The red segments indicate the maximum permissible engine revolutions per minute (RPM x 1000) for each gear range. Before reaching the red area, ease up on the accelerator.

16. High Beam Light

the turn signal

This light shows that the headlights are on high beam. Pull lever towards the steering wheel to switch the headlights from high or low beam. 17. Front Fog Light Indicator — If Equipped

This light shows when the front fog lights are ON.

18. Seat Belt Reminder Light

When the ignition switch is first turned ON, this light will turn on for five to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver’s seat belt remains unbuckled, the Seat Belt Reminder Light will illuminate and the chime will sound. Refer to the Occupant Re- straints section for more information.

19. Malfunction Indicator Light

This light is part of an onboard diagnostic system called OBD that monitors engine and automatic transmission control systems. The light will illu- minate when the key is in the ON position before engine start. If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing. If the Malfunction Indicator Light flashes when the engine is running, serious conditions may exist that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs.

UNDERSTANDING YOUR INSTRUMENT PANEL 233

20. Airbag Light

This light turns on and remains on for seven seconds as a bulb check when the ignition switch is first turned ON. If the light is not on during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible. 21. Temperature Gauge

The temperature gauge shows engine coolant tem- perature. Any reading within the normal range indicates that the engine cooling system is operat-

ing satisfactorily. The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range.

234 UNDERSTANDING YOUR INSTRUMENT PANEL

CAUTION!

WARNING!

Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “H“, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, and you hear continuous chimes, turn the engine off immediately, and call your autho- rized dealership for service.

A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer- ship for service if your vehicle overheats. If you decide to look under the hood yourself, see Section 7
of this manual. Follow the warnings under the Cool- ing System Pressure Cap paragraph.

22. Trip/Odometer Display Reset Button — Base Cluster To reset a trip odometer, display the trip odometer to be reset then push and hold the button until the display resets (approximately two seconds). The odometer must be in TRIP mode to reset it.

To reset a message display (gATE, gASCAP, noFUSE, CHAngE OIL, LoCOOL, LoWASH), push and hold the button until the display resets (approximately two sec- onds). Trip/Odometer Display Reset Button — Premium Cluster Press this button to change the display from odometer to either of two trip odometer settings. The letter “A” or “B” will appear when in the trip odometer mode. Push in and hold the button for two seconds to reset the trip odometer to 0 mi (km). The odometer must be in TRIP mode to reset it. 23. Transmission Range Indicator This display indicator shows the automatic transaxle gear selection. NOTE: You must apply the brakes before shifting from PARK.

UNDERSTANDING YOUR INSTRUMENT PANEL 235

24. Odometer Display Area When the appropriate conditions exist, the following odometer messages will display:

CHAngE OIL . . . . . . . . . . . . . . . Oil Change Required CRUISE. . . . . . . . . . . . . . . . . . . . . Cruise Control On door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Ajar ESPOFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . ESP Off gATE . . . . . . . . . . . . . . . . . . . . . . . . . . Lift Gate Ajar gASCAP . . . . . . . . . . . . . . . . . . . . . . . Fuel Cap Fault hood* . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hood Ajar noFUSE . . . . . . . . . . . . . . . . . . . . . . . . . . Fuse Fault LoCOOL . . . . . . . . . . . . . . . . . . . . . . . . Low Coolant LoWASH . . . . . . . . . . . . . . . . . . . . Low Washer Fluid If your vehicle is equipped with a hood switch, NOTE: in the case of hood ajar, a warning message will be displayed in either the PRNDL/Odometer display as “hood” or “Hood Ajar” in the EVIC display.

236 UNDERSTANDING YOUR INSTRUMENT PANEL

NOTE: Some of the above warnings will be displayed in the Compass Mini-Trip Computer / Electronic Vehicle Information Center Display Area under the Speedometer. Refer to” Compass Mini-Trip Computer (CMTC) — If Equipped”, later in this section for more information. CHAngE OIL Your vehicle is equipped with an engine oil change indicator system. The CHAngE OIL message will flash in the instrument cluster odometer for approximately 12
seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle-based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and

release the Trip / Odometer Display reset button on the instrument cluster. To reset the oil change indicator system (after performing the scheduled maintenance) refer to the following procedure. 1. Turn the ignition switch to the ON position (Do not start the engine). 2. Fully depress the accelerator pedal slowly three times within 10 seconds.